include/configs/omap3_evm.h

   1 /*
   2  * Configuration settings for the TI OMAP3 EVM board.
   3  *
   4  * Copyright (C) 2006-2011 Texas Instruments Incorporated - http://www.ti.com/
   5  *
   6  * Author :
   7  *      Manikandan Pillai <mani.pillai@ti.com>
   8  * Derived from Beagle Board and 3430 SDP code by
   9  *      Richard Woodruff <r-woodruff2@ti.com>
  10  *      Syed Mohammed Khasim <khasim@ti.com>
  11  *
  12  * Manikandan Pillai <mani.pillai@ti.com>
  13  *
  14  * SPDX-License-Identifier:     GPL-2.0+
  15  */
  16
  17 #ifndef __OMAP3EVM_CONFIG_H
  18 #define __OMAP3EVM_CONFIG_H
  19
  20 #include <asm/arch/cpu.h>
  21 #include <asm/arch/omap.h>
  22
  23 /* ----------------------------------------------------------------------------
  24  * Supported U-Boot commands
  25  * ----------------------------------------------------------------------------
  26  */
  27
  28 #define CONFIG_CMD_JFFS2
  29
  30 #define CONFIG_CMD_NAND
  31
  32 /* ----------------------------------------------------------------------------
  33  * Supported U-Boot features
  34  * ----------------------------------------------------------------------------
  35  */
  36 #define CONFIG_SYS_LONGHELP
  37
  38 /* Display CPU and Board information */
  39 #define CONFIG_DISPLAY_CPUINFO
  40 #define CONFIG_DISPLAY_BOARDINFO
  41
  42 /* Allow to overwrite serial and ethaddr */
  43 #define CONFIG_ENV_OVERWRITE
  44
  45 /* Add auto-completion support */
  46 #define CONFIG_AUTO_COMPLETE
  47
  48 /* ----------------------------------------------------------------------------
  49  * Supported hardware
  50  * ----------------------------------------------------------------------------
  51  */
  52
  53 /* MMC */
  54 #define CONFIG_MMC
  55 #define CONFIG_GENERIC_MMC
  56 #define CONFIG_OMAP_HSMMC
  57
  58 /* SPL */
  59 #define CONFIG_SPL_MMC_SUPPORT
  60 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
  61 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS      0x200 /* 256 KB */
  62 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION      1
  63 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
  64
  65 /* Partition tables */
  66 #define CONFIG_EFI_PARTITION
  67 #define CONFIG_DOS_PARTITION
  68
  69 /* USB
  70  *
  71  * Enable CONFIG_USB_MUSB_HCD for Host functionalities MSC, keyboard
  72  * Enable CONFIG_USB_MUSB_UDD for Device functionalities.
  73  */
  74 #define CONFIG_USB_OMAP3
  75 #define CONFIG_USB_MUSB_HCD
  76 /* #define CONFIG_USB_MUSB_UDC */
  77
  78 /* NAND SPL */
  79 #define CONFIG_SPL_NAND_SIMPLE
  80 #define CONFIG_SPL_NAND_SUPPORT
  81 #define CONFIG_SPL_NAND_BASE
  82 #define CONFIG_SPL_NAND_DRIVERS
  83 #define CONFIG_SPL_NAND_ECC
  84 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
  85 #define CONFIG_SYS_NAND_PAGE_COUNT      64
  86 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
  87 #define CONFIG_SYS_NAND_OOBSIZE         64
  88 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128*1024)
  89 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   0
  90 #define CONFIG_SYS_NAND_ECCPOS          {2, 3, 4, 5, 6, 7, 8, 9,\
  91                                                 10, 11, 12, 13}
  92 #define CONFIG_SYS_NAND_ECCSIZE         512
  93 #define CONFIG_SYS_NAND_ECCBYTES        3
  94 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_HAM1_CODE_HW
  95 #define CONFIG_SYS_NAND_U_BOOT_START   CONFIG_SYS_TEXT_BASE
  96 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
  97
  98 /*
  99  * High level configuration options
 100  */
 101 #define CONFIG_OMAP                     /* This is TI OMAP core */
 102 #define CONFIG_OMAP_GPIO
 103 #define CONFIG_OMAP_COMMON
 104 /* Common ARM Erratas */
 105 #define CONFIG_ARM_ERRATA_454179
 106 #define CONFIG_ARM_ERRATA_430973
 107 #define CONFIG_ARM_ERRATA_621766
 108
 109 #define CONFIG_SDRC                     /* The chip has SDRC controller */
 110
 111 #define CONFIG_OMAP3_EVM                /* This is a OMAP3 EVM */
 112 #define CONFIG_TWL4030_POWER            /* with TWL4030 PMIC */
 113
 114 /*
 115  * Clock related definitions
 116  */
 117 #define V_OSCK                  26000000        /* Clock output from T2 */
 118 #define V_SCLK                  (V_OSCK >> 1)
 119
 120 /*
 121  * OMAP3 has 12 GP timers, they can be driven by the system clock
 122  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
 123  * This rate is divided by a local divisor.
 124  */
 125 #define CONFIG_SYS_TIMERBASE            OMAP34XX_GPT2
 126 #define CONFIG_SYS_PTV                  2       /* Divisor: 2^(PTV+1) => 8 */
 127
 128 /* Size of environment - 128KB */
 129 #define CONFIG_ENV_SIZE                 (128 << 10)
 130
 131 /* Size of malloc pool */
 132 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + (128 << 10))
 133
 134 /*
 135  * Physical Memory Map
 136  * Note 1: CS1 may or may not be populated
 137  * Note 2: SDRAM size is expected to be at least 32MB
 138  */
 139 #define CONFIG_NR_DRAM_BANKS            2
 140 #define PHYS_SDRAM_1                    OMAP34XX_SDRC_CS0
 141 #define PHYS_SDRAM_2                    OMAP34XX_SDRC_CS1
 142
 143 /* Limits for memtest */
 144 #define CONFIG_SYS_MEMTEST_START        (OMAP34XX_SDRC_CS0)
 145 #define CONFIG_SYS_MEMTEST_END          (OMAP34XX_SDRC_CS0 + \
 146                                                 0x01F00000) /* 31MB */
 147
 148 /* Default load address */
 149 #define CONFIG_SYS_LOAD_ADDR            (OMAP34XX_SDRC_CS0)
 150
 151 /* -----------------------------------------------------------------------------
 152  * Hardware drivers
 153  * -----------------------------------------------------------------------------
 154  */
 155
 156 /*
 157  * NS16550 Configuration
 158  */
 159 #define V_NS16550_CLK                   48000000        /* 48MHz (APLL96/2) */
 160
 161 #define CONFIG_SYS_NS16550_SERIAL
 162 #define CONFIG_SYS_NS16550_REG_SIZE     (-4)
 163 #define CONFIG_SYS_NS16550_CLK          V_NS16550_CLK
 164
 165 /*
 166  * select serial console configuration
 167  */
 168 #define CONFIG_CONS_INDEX               1
 169 #define CONFIG_SERIAL1                  1       /* UART1 on OMAP3 EVM */
 170 #define CONFIG_SYS_NS16550_COM1         OMAP34XX_UART1
 171 #define CONFIG_BAUDRATE                 115200
 172 #define CONFIG_SYS_BAUDRATE_TABLE       {4800, 9600, 19200, 38400, 57600,\
 173                                         115200}
 174
 175 /*
 176  * I2C
 177  */
 178 #define CONFIG_SYS_I2C
 179 #define CONFIG_SYS_OMAP24_I2C_SPEED     100000
 180 #define CONFIG_SYS_OMAP24_I2C_SLAVE     1
 181 #define CONFIG_SYS_I2C_OMAP34XX
 182
 183 /*
 184  * PISMO support
 185  */
 186 /* Monitor at start of flash - Reserve 2 sectors */
 187 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_FLASH_BASE
 188
 189 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)
 190
 191 /* Start location & size of environment */
 192 #define ONENAND_ENV_OFFSET              0x260000
 193 #define SMNAND_ENV_OFFSET               0x260000
 194
 195 #define CONFIG_SYS_ENV_SECT_SIZE        (128 << 10)     /* 128 KiB */
 196
 197 /*
 198  * NAND
 199  */
 200 /* Physical address to access NAND */
 201 #define CONFIG_SYS_NAND_ADDR            NAND_BASE
 202
 203 /* Physical address to access NAND at CS0 */
 204 #define CONFIG_SYS_NAND_BASE            NAND_BASE
 205
 206 /* Max number of NAND devices */
 207 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 208 #define CONFIG_SYS_NAND_BUSWIDTH_16BIT
 209 /* Timeout values (in ticks) */
 210 #define CONFIG_SYS_FLASH_ERASE_TOUT     (100 * CONFIG_SYS_HZ)
 211 #define CONFIG_SYS_FLASH_WRITE_TOUT     (100 * CONFIG_SYS_HZ)
 212
 213 /* Flash banks JFFS2 should use */
 214 #define CONFIG_SYS_MAX_MTD_BANKS        (CONFIG_SYS_MAX_FLASH_BANKS + \
 215                                                 CONFIG_SYS_MAX_NAND_DEVICE)
 216
 217 #define CONFIG_SYS_JFFS2_MEM_NAND
 218 #define CONFIG_SYS_JFFS2_FIRST_BANK     CONFIG_SYS_MAX_FLASH_BANKS
 219 #define CONFIG_SYS_JFFS2_NUM_BANKS      1
 220
 221 #define CONFIG_JFFS2_NAND
 222 /* nand device jffs2 lives on */
 223 #define CONFIG_JFFS2_DEV                "nand0"
 224 /* Start of jffs2 partition */
 225 #define CONFIG_JFFS2_PART_OFFSET        0x680000
 226 /* Size of jffs2 partition */
 227 #define CONFIG_JFFS2_PART_SIZE          0xf980000
 228
 229 /*
 230  * USB
 231  */
 232 #ifdef CONFIG_USB_OMAP3
 233
 234 #ifdef CONFIG_USB_MUSB_HCD
 235
 236 #define CONGIG_CMD_STORAGE
 237
 238 #ifdef CONFIG_USB_KEYBOARD
 239 #define CONFIG_SYS_USB_EVENT_POLL
 240 #define CONFIG_PREBOOT                  "usb start"
 241 #endif /* CONFIG_USB_KEYBOARD */
 242
 243 #endif /* CONFIG_USB_MUSB_HCD */
 244
 245 #ifdef CONFIG_USB_MUSB_UDC
 246 /* USB device configuration */
 247 #define CONFIG_USB_DEVICE
 248 #define CONFIG_USB_TTY
 249 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 250
 251 /* Change these to suit your needs */
 252 #define CONFIG_USBD_VENDORID            0x0451
 253 #define CONFIG_USBD_PRODUCTID           0x5678
 254 #define CONFIG_USBD_MANUFACTURER        "Texas Instruments"
 255 #define CONFIG_USBD_PRODUCT_NAME        "EVM"
 256 #endif /* CONFIG_USB_MUSB_UDC */
 257
 258 #endif /* CONFIG_USB_OMAP3 */
 259
 260 /* ----------------------------------------------------------------------------
 261  * U-Boot features
 262  * ----------------------------------------------------------------------------
 263  */
 264 #define CONFIG_SYS_MAXARGS              16      /* max args for a command */
 265
 266 #define CONFIG_MISC_INIT_R
 267
 268 #define CONFIG_CMDLINE_TAG                      /* enable passing of ATAGs */
 269 #define CONFIG_SETUP_MEMORY_TAGS
 270 #define CONFIG_INITRD_TAG
 271 #define CONFIG_REVISION_TAG
 272
 273 /* Size of Console IO buffer */
 274 #define CONFIG_SYS_CBSIZE               512
 275
 276 /* Size of print buffer */
 277 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 278                                                 sizeof(CONFIG_SYS_PROMPT) + 16)
 279
 280 /* Size of bootarg buffer */
 281 #define CONFIG_SYS_BARGSIZE             (CONFIG_SYS_CBSIZE)
 282
 283 #define CONFIG_BOOTFILE                 "uImage"
 284
 285 /*
 286  * NAND / OneNAND
 287  */
 288 #if defined(CONFIG_CMD_NAND)
 289 #define CONFIG_SYS_FLASH_BASE           NAND_BASE
 290
 291 #define CONFIG_NAND_OMAP_GPMC
 292 #define CONFIG_ENV_OFFSET               SMNAND_ENV_OFFSET
 293 #elif defined(CONFIG_CMD_ONENAND)
 294 #define CONFIG_SYS_FLASH_BASE           ONENAND_MAP
 295 #define CONFIG_SYS_ONENAND_BASE         ONENAND_MAP
 296 #endif
 297
 298 #if !defined(CONFIG_ENV_IS_NOWHERE)
 299 #if defined(CONFIG_CMD_NAND)
 300 #define CONFIG_ENV_IS_IN_NAND
 301 #elif defined(CONFIG_CMD_ONENAND)
 302 #define CONFIG_ENV_IS_IN_ONENAND
 303 #define CONFIG_ENV_OFFSET               ONENAND_ENV_OFFSET
 304 #endif
 305 #endif /* CONFIG_ENV_IS_NOWHERE */
 306
 307 #define CONFIG_ENV_ADDR                 CONFIG_ENV_OFFSET
 308
 309 #if defined(CONFIG_CMD_NET)
 310
 311 /* Ethernet (SMSC9115 from SMSC9118 family) */
 312 #define CONFIG_SMC911X
 313 #define CONFIG_SMC911X_32_BIT
 314 #define CONFIG_SMC911X_BASE             0x2C000000
 315
 316 /* BOOTP fields */
 317 #define CONFIG_BOOTP_SUBNETMASK         0x00000001
 318 #define CONFIG_BOOTP_GATEWAY            0x00000002
 319 #define CONFIG_BOOTP_HOSTNAME           0x00000004
 320 #define CONFIG_BOOTP_BOOTPATH           0x00000010
 321
 322 #endif /* CONFIG_CMD_NET */
 323
 324 /* Support for relocation */
 325 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
 326 #define CONFIG_SYS_INIT_RAM_ADDR        0x4020f800
 327 #define CONFIG_SYS_INIT_RAM_SIZE        0x800
 328 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_INIT_RAM_ADDR + \
 329                                          CONFIG_SYS_INIT_RAM_SIZE - \
 330                                          GENERATED_GBL_DATA_SIZE)
 331
 332 /* -----------------------------------------------------------------------------
 333  * Board specific
 334  * -----------------------------------------------------------------------------
 335  */
 336 #define CONFIG_SYS_NO_FLASH
 337
 338 /* Uncomment to define the board revision statically */
 339 /* #define CONFIG_STATIC_BOARD_REV      OMAP3EVM_BOARD_GEN_2 */
 340
 341 /* Defines for SPL */
 342 #define CONFIG_SPL_FRAMEWORK
 343 #define CONFIG_SPL_TEXT_BASE            0x40200800
 344 #define CONFIG_SPL_MAX_SIZE             (SRAM_SCRATCH_SPACE_ADDR - \
 345                                          CONFIG_SPL_TEXT_BASE)
 346
 347 #define CONFIG_SPL_BSS_START_ADDR       0x80000000
 348 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000         /* 512 KB */
 349
 350 #define CONFIG_SPL_BOARD_INIT
 351 #define CONFIG_SPL_SERIAL_SUPPORT
 352 #define CONFIG_SPL_POWER_SUPPORT
 353 #define CONFIG_SPL_OMAP3_ID_NAND
 354 #define CONFIG_SPL_LDSCRIPT             "$(CPUDIR)/omap-common/u-boot-spl.lds"
 355
 356 /*
 357  * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
 358  * 64 bytes before this address should be set aside for u-boot.img's
 359  * header. That is 0x800FFFC0--0x80100000 should not be used for any
 360  * other needs.
 361  */
 362 #define CONFIG_SYS_TEXT_BASE            0x80100000
 363 #define CONFIG_SYS_SPL_MALLOC_START     0x80208000
 364 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
 365
 366 /* -----------------------------------------------------------------------------
 367  * Default environment
 368  * -----------------------------------------------------------------------------
 369  */
 370
 371 #define CONFIG_EXTRA_ENV_SETTINGS \
 372         "loadaddr=0x82000000\0" \
 373         "usbtty=cdc_acm\0" \
 374         "mmcdev=0\0" \
 375         "console=ttyO0,115200n8\0" \
 376         "mmcargs=setenv bootargs console=${console} " \
 377                 "root=/dev/mmcblk0p2 rw " \
 378                 "rootfstype=ext3 rootwait\0" \
 379         "nandargs=setenv bootargs console=${console} " \
 380                 "root=/dev/mtdblock4 rw " \
 381                 "rootfstype=jffs2\0" \
 382         "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
 383         "bootscript=echo Running bootscript from mmc ...; " \
 384                 "source ${loadaddr}\0" \
 385         "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
 386         "mmcboot=echo Booting from mmc ...; " \
 387                 "run mmcargs; " \
 388                 "bootm ${loadaddr}\0" \
 389         "nandboot=echo Booting from nand ...; " \
 390                 "run nandargs; " \
 391                 "onenand read ${loadaddr} 280000 400000; " \
 392                 "bootm ${loadaddr}\0" \
 393
 394 #define CONFIG_BOOTCOMMAND \
 395         "mmc dev ${mmcdev}; if mmc rescan; then " \
 396                 "if run loadbootscript; then " \
 397                         "run bootscript; " \
 398                 "else " \
 399                         "if run loaduimage; then " \
 400                                 "run mmcboot; " \
 401                         "else run nandboot; " \
 402                         "fi; " \
 403                 "fi; " \
 404         "else run nandboot; fi"
 405
 406 #endif /* __OMAP3EVM_CONFIG_H */