include/configs/omap3_logic.h

   1 /*
   2  * (C) Copyright 2011 Logic Product Development <www.logicpd.com>
   3  *      Peter Barada <peter.barada@logicpd.com>
   4  *
   5  * Configuration settings for the Logic OMAP35x/DM37x SOM LV/Torpedo
   6  * reference boards.
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /* High Level Configuration Options */
  15
  16 #define CONFIG_NR_DRAM_BANKS    2       /* CS1 may or may not be populated */
  17
  18 /*
  19  * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
  20  * 64 bytes before this address should be set aside for u-boot.img's
  21  * header. That is 0x800FFFC0--0x80100000 should not be used for any
  22  * other needs.  We use this rather than the inherited defines from
  23  * ti_armv7_common.h for backwards compatibility.
  24  */
  25 #define CONFIG_SYS_TEXT_BASE            0x80100000
  26 #define CONFIG_SPL_BSS_START_ADDR       0x80000000
  27 #define CONFIG_SPL_BSS_MAX_SIZE         (512 << 10)     /* 512 KB */
  28 #define CONFIG_SYS_SPL_MALLOC_START     0x80208000
  29 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  30
  31 #include <configs/ti_omap3_common.h>
  32
  33 /* Override default SPL info to minimize empty space and allow BCH8 in SPL */
  34 #undef CONFIG_SPL_TEXT_BASE
  35 #undef CONFIG_SPL_MAX_SIZE
  36 #define CONFIG_SPL_TEXT_BASE   0x40200000
  37 #define CONFIG_SPL_MAX_SIZE    (64 * 1024)
  38
  39 /* Display CPU and Board information */
  40
  41 #define CONFIG_DISPLAY_CPUINFO
  42 #define CONFIG_DISPLAY_BOARDINFO
  43 #define CONFIG_BOARD_LATE_INIT
  44 #define CONFIG_MISC_INIT_R              /* misc_init_r dumps the die id */
  45 #define CONFIG_CMDLINE_TAG              /* enable passing of ATAGs */
  46 #define CONFIG_SETUP_MEMORY_TAGS
  47 #define CONFIG_INITRD_TAG
  48 #define CONFIG_REVISION_TAG
  49 #define CONFIG_CMDLINE_EDITING          /* cmd line edit/history */
  50 #define CONFIG_ZERO_BOOTDELAY_CHECK     /* check keypress w/no delay */
  51
  52 /* Hardware drivers */
  53
  54 /* GPIO banks */
  55 #define CONFIG_OMAP3_GPIO_6             /* GPIO160..191 is in GPIO bank 6 */
  56
  57 #define CONFIG_USB_OMAP3
  58
  59 /* select serial console configuration */
  60 #undef CONFIG_CONS_INDEX
  61 #define CONFIG_CONS_INDEX               1
  62 #define CONFIG_SYS_NS16550_COM1         OMAP34XX_UART1
  63 #define CONFIG_SERIAL1                  1       /* UART1 on OMAP Logic boards */
  64
  65 /* commands to include */
  66 #define CONFIG_CMD_NAND
  67 #define CONFIG_CMD_CACHE
  68 #define CONFIG_CMD_EXT2
  69 #define CONFIG_CMD_FAT
  70 #define CONFIG_CMD_MTDPARTS
  71 #define CONFIG_CMD_NAND_LOCK_UNLOCK     /* nand (un)lock commands       */
  72
  73 /* I2C */
  74 #define CONFIG_SYS_I2C_OMAP34XX
  75 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50    /* EEPROM AT24C64      */
  76 #define EXPANSION_EEPROM_I2C_BUS        2       /* I2C Bus for AT24C64 */
  77 #define CONFIG_OMAP3_LOGIC_USE_NEW_PRODUCT_ID
  78
  79 /* USB */
  80 #define CONFIG_USB_MUSB_OMAP2PLUS
  81 #define CONFIG_USB_MUSB_PIO_ONLY
  82 #define CONFIG_USB_ETHER
  83 #define CONFIG_USB_ETHER_RNDIS
  84 #define CONFIG_USB_FUNCTION_FASTBOOT
  85 #define CONFIG_CMD_FASTBOOT
  86 #define CONFIG_ANDROID_BOOT_IMAGE
  87 #define CONFIG_FASTBOOT_BUF_ADDR        CONFIG_SYS_LOAD_ADDR
  88 #define CONFIG_FASTBOOT_BUF_SIZE        0x07000000
  89 #define CONFIG_SYS_CACHELINE_SIZE       64
  90
  91 /* TWL4030 */
  92 #define CONFIG_TWL4030_PWM
  93 #define CONFIG_TWL4030_USB
  94
  95 /* Board NAND Info. */
  96 #ifdef CONFIG_NAND
  97 #define CONFIG_NAND_OMAP_GPMC
  98
  99 #define CONFIG_CMD_UBI                  /* UBI-formated MTD partition support */
 100 #define CONFIG_CMD_UBIFS                /* Read-only UBI volume operations */
 101 #define CONFIG_RBTREE                   /* required by CONFIG_CMD_UBI */
 102 #define CONFIG_LZO                      /* required by CONFIG_CMD_UBIFS */
 103
 104 #define CONFIG_SYS_NAND_ADDR            NAND_BASE /* physical address */
 105                                                   /* to access nand */
 106 #define CONFIG_SYS_MAX_NAND_DEVICE      1         /* Max number of */
 107                                                   /* NAND devices */
 108 #define CONFIG_SYS_NAND_BUSWIDTH_16BIT
 109 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 110 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 111 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
 112 #define CONFIG_SYS_NAND_OOBSIZE         64
 113 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 114 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   NAND_LARGE_BADBLOCK_POS
 115 #define CONFIG_SYS_NAND_ECCPOS          {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, \
 116                                          13, 14, 16, 17, 18, 19, 20, 21, 22, \
 117                                          23, 24, 25, 26, 27, 28, 30, 31, 32, \
 118                                          33, 34, 35, 36, 37, 38, 39, 40, 41, \
 119                                          42, 44, 45, 46, 47, 48, 49, 50, 51, \
 120                                          52, 53, 54, 55, 56}
 121
 122 #define CONFIG_SYS_NAND_ECCSIZE         512
 123 #define CONFIG_SYS_NAND_ECCBYTES        13
 124 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
 125 #define CONFIG_BCH
 126 #define CONFIG_SYS_NAND_MAX_OOBFREE     2
 127 #define CONFIG_SYS_NAND_MAX_ECCPOS      56
 128 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
 129 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
 130 #define CONFIG_MTD_PARTITIONS           /* required for UBI partition support */
 131 #define MTDIDS_DEFAULT                  "nand0=omap2-nand.0"
 132 #define MTDPARTS_DEFAULT                "mtdparts=omap2-nand.0:512k(MLO),"\
 133                                         "1920k(u-boot),128k(u-boot-env),"\
 134                                         "4m(kernel),-(fs)"
 135 #endif
 136
 137 /* Environment information */
 138
 139 /*
 140  * PREBOOT assumes the 4.3" display is attached.  User can interrupt
 141  * and modify display variable to suit their needs.
 142  */
 143 #define CONFIG_PREBOOT \
 144         "echo ======================NOTICE============================;"\
 145         "echo \"The u-boot environment is not set.\";"                  \
 146         "echo \"If using a display a valid display varible for your panel\";" \
 147         "echo \"needs to be set.\";"                                    \
 148         "echo \"Valid display options are:\";"                          \
 149         "echo \"  2 == LQ121S1DG31     TFT SVGA    (12.1)  Sharp\";"    \
 150         "echo \"  3 == LQ036Q1DA01     TFT QVGA    (3.6)   Sharp w/ASIC\";" \
 151         "echo \"  5 == LQ064D343       TFT VGA     (6.4)   Sharp\";"    \
 152         "echo \"  7 == LQ10D368        TFT VGA     (10.4)  Sharp\";"    \
 153         "echo \" 15 == LQ043T1DG01     TFT WQVGA   (4.3)   Sharp (DEFAULT)\";" \
 154         "echo \" vga[-dvi or -hdmi]    LCD VGA     640x480\";"          \
 155         "echo \" svga[-dvi or -hdmi]   LCD SVGA    800x600\";"          \
 156         "echo \" xga[-dvi or -hdmi]    LCD XGA     1024x768\";"         \
 157         "echo \" 720p[-dvi or -hdmi]   LCD 720P    1280x720\";"         \
 158         "echo \"Defaulting to 4.3 LCD panel (display=15).\";"           \
 159         "setenv display 15;"                                            \
 160         "setenv preboot;"                                               \
 161         "nand unlock;"                                                  \
 162         "saveenv;"
 163
 164 #define CONFIG_EXTRA_ENV_SETTINGS \
 165         "loadaddr=0x81000000\0" \
 166         "uimage=uImage\0" \
 167         "zimage=zImage\0" \
 168         "mtdids=" MTDIDS_DEFAULT "\0"   \
 169         "mtdparts=" MTDPARTS_DEFAULT "\0" \
 170         "mmcdev=0\0" \
 171         "mmcroot=/dev/mmcblk0p2 rw\0" \
 172         "mmcrootfstype=ext4 rootwait\0" \
 173         "nandroot=ubi0:rootfs rw ubi.mtd=fs noinitrd\0" \
 174         "nandrootfstype=ubifs rootwait\0" \
 175         "autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \
 176                         "if run loadbootscript; then " \
 177                                 "run bootscript; " \
 178                         "else " \
 179                                 "run defaultboot;" \
 180                         "fi; " \
 181                 "else run defaultboot; fi\0" \
 182         "defaultboot=run mmcramboot\0" \
 183         "consoledevice=ttyO0\0" \
 184         "display=15\0" \
 185         "setconsole=setenv console ${consoledevice},${baudrate}n8\0" \
 186         "dump_bootargs=echo 'Bootargs: '; echo $bootargs\0" \
 187         "rotation=0\0" \
 188         "vrfb_arg=if itest ${rotation} -ne 0; then " \
 189                 "setenv bootargs ${bootargs} omapfb.vrfb=y " \
 190                 "omapfb.rotate=${rotation}; " \
 191                 "fi\0" \
 192         "optargs=ignore_loglevel early_printk no_console_suspend\0" \
 193         "addmtdparts=setenv bootargs ${bootargs} ${mtdparts}\0" \
 194         "common_bootargs=setenv bootargs ${bootargs} display=${display} " \
 195                 "${optargs};" \
 196                 "run addmtdparts; " \
 197                 "run vrfb_arg\0" \
 198         "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
 199         "bootscript=echo 'Running bootscript from mmc ...'; " \
 200                 "source ${loadaddr}\0" \
 201         "loaduimage=mmc rescan; " \
 202                 "fatload mmc ${mmcdev} ${loadaddr} ${uimage}\0" \
 203         "loadzimage=mmc rescan; " \
 204                 "fatload mmc ${mmcdev} ${loadaddr} ${zimage}\0" \
 205         "ramdisksize=64000\0" \
 206         "ramdiskaddr=0x82000000\0" \
 207         "ramdiskimage=rootfs.ext2.gz.uboot\0" \
 208         "loadramdisk=mmc rescan; " \
 209                 "fatload mmc ${mmcdev} ${ramdiskaddr} ${ramdiskimage}\0" \
 210         "ramargs=run setconsole; setenv bootargs console=${console} " \
 211                 "root=/dev/ram rw ramdisk_size=${ramdisksize}\0" \
 212         "mmcargs=run setconsole; setenv bootargs console=${console} " \
 213                 "${optargs} " \
 214                 "root=${mmcroot} " \
 215                 "rootfstype=${mmcrootfstype}\0" \
 216         "nandargs=run setconsole; setenv bootargs console=${console} " \
 217                 "${optargs} " \
 218                 "root=${nandroot} " \
 219                 "rootfstype=${nandrootfstype}\0" \
 220         "fdtaddr=0x86000000\0" \
 221         "loadfdtimage=mmc rescan; " \
 222                 "fatload mmc ${mmcdev} ${fdtaddr} ${fdtimage}\0" \
 223         "mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
 224                 "run mmcargs; " \
 225                 "run common_bootargs; " \
 226                 "run dump_bootargs; " \
 227                 "run loadzimage; " \
 228                 "run loadfdtimage; " \
 229                 "bootz ${loadaddr} - ${fdtaddr}\0" \
 230         "mmcramboot=echo 'Booting uImage kernel from mmc w/ramdisk...'; " \
 231                 "run ramargs; " \
 232                 "run common_bootargs; " \
 233                 "run dump_bootargs; " \
 234                 "run loaduimage; " \
 235                 "run loadramdisk; " \
 236                 "bootm ${loadaddr} ${ramdiskaddr}\0" \
 237         "mmcrambootz=echo 'Booting zImage kernel from mmc w/ramdisk...'; " \
 238                 "run ramargs; " \
 239                 "run common_bootargs; " \
 240                 "run dump_bootargs; " \
 241                 "run loadzimage; " \
 242                 "run loadramdisk; " \
 243                 "run loadfdtimage; " \
 244                 "bootz ${loadaddr} ${ramdiskaddr} ${fdtaddr}\0; " \
 245         "tftpboot=echo 'Booting kernel/ramdisk rootfs from tftp...'; " \
 246                 "run ramargs; " \
 247                 "run common_bootargs; " \
 248                 "run dump_bootargs; " \
 249                 "tftpboot ${loadaddr} ${uimage}; " \
 250                 "tftpboot ${ramdiskaddr} ${ramdiskimage}; " \
 251                 "bootm ${loadaddr} ${ramdiskaddr}\0"
 252
 253 #define CONFIG_BOOTCOMMAND \
 254         "run autoboot"
 255
 256 /* Miscellaneous configurable options */
 257 #define CONFIG_AUTO_COMPLETE
 258
 259 /* memtest works on */
 260 #define CONFIG_SYS_MEMTEST_START        (OMAP34XX_SDRC_CS0)
 261 #define CONFIG_SYS_MEMTEST_END          (OMAP34XX_SDRC_CS0 + \
 262                                         0x01F00000) /* 31MB */
 263
 264 /* FLASH and environment organization */
 265
 266 /* **** PISMO SUPPORT *** */
 267 #if defined(CONFIG_CMD_NAND)
 268 #define CONFIG_SYS_FLASH_BASE           NAND_BASE
 269 #elif defined(CONFIG_CMD_ONENAND)
 270 #define CONFIG_SYS_FLASH_BASE           ONENAND_MAP
 271 #endif
 272
 273 /* Monitor at start of flash */
 274 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_FLASH_BASE
 275
 276 #define CONFIG_ENV_IS_IN_NAND           1
 277 #define CONFIG_ENV_SIZE                 (128 << 10)     /* 128 KiB */
 278 #define ONENAND_ENV_OFFSET              0x260000 /* environment starts here */
 279 #define SMNAND_ENV_OFFSET               0x260000 /* environment starts here */
 280
 281 #define CONFIG_SYS_ENV_SECT_SIZE        (128 << 10)     /* 128 KiB */
 282 #define CONFIG_ENV_OFFSET               SMNAND_ENV_OFFSET
 283 #define CONFIG_ENV_ADDR                 SMNAND_ENV_OFFSET
 284
 285 /* SMSC922x Ethernet */
 286 #if defined(CONFIG_CMD_NET)
 287 #define CONFIG_SMC911X
 288 #define CONFIG_SMC911X_32_BIT
 289 #define CONFIG_SMC911X_BASE     0x08000000
 290 #endif /* (CONFIG_CMD_NET) */
 291
 292 /* Defines for SPL */
 293
 294 #define CONFIG_SPL_OMAP3_ID_NAND
 295
 296 /* NAND: SPL falcon mode configs */
 297 #ifdef CONFIG_SPL_OS_BOOT
 298 #define CONFIG_CMD_SPL_NAND_OFS         0x240000
 299 #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
 300 #define CONFIG_CMD_SPL_WRITE_SIZE       0x2000
 301 #endif
 302
 303 #endif /* __CONFIG_H */