include/configs/picosam9g45.h

   1 /*
   2  * Configuration settings for the mini-box PICOSAM9G45 board.
   3  * (C) Copyright 2015 Inter Act B.V.
   4  *
   5  * Based on:
   6  * U-Boot file: include/configs/at91sam9m10g45ek.h
   7  * (C) Copyright 2007-2008
   8  * Stelian Pop <stelian@popies.net>
   9  * Lead Tech Design <www.leadtechdesign.com>
  10  *
  11  * SPDX-License-Identifier:     GPL-2.0+
  12  */
  13
  14 #ifndef __CONFIG_H
  15 #define __CONFIG_H
  16
  17 #include <asm/hardware.h>
  18
  19 #define CONFIG_SYS_TEXT_BASE            0x23f00000
  20
  21 #define CONFIG_ATMEL_LEGACY             /* required until (g)pio is fixed */
  22
  23 /* ARM asynchronous clock */
  24 #define CONFIG_SYS_AT91_SLOW_CLOCK      32768
  25 #define CONFIG_SYS_AT91_MAIN_CLOCK      12000000 /* from 12 MHz crystal */
  26
  27 #define CONFIG_PICOSAM
  28
  29 #define CONFIG_CMDLINE_TAG              /* enable passing of ATAGs      */
  30 #define CONFIG_SETUP_MEMORY_TAGS
  31 #define CONFIG_INITRD_TAG
  32 #define CONFIG_SKIP_LOWLEVEL_INIT
  33
  34 /* general purpose I/O */
  35 #define CONFIG_ATMEL_LEGACY             /* required until (g)pio is fixed */
  36 #define CONFIG_AT91_GPIO
  37 #define CONFIG_AT91_GPIO_PULLUP 1       /* keep pullups on peripheral pins */
  38
  39 /* serial console */
  40 #define CONFIG_ATMEL_USART
  41 #define CONFIG_USART_BASE               ATMEL_BASE_DBGU
  42 #define CONFIG_USART_ID                 ATMEL_ID_SYS
  43
  44 /* LCD */
  45 #define LCD_BPP                         LCD_COLOR8
  46 #define CONFIG_LCD_LOGO
  47 #undef LCD_TEST_PATTERN
  48 #define CONFIG_LCD_INFO
  49 #define CONFIG_LCD_INFO_BELOW_LOGO
  50 #define CONFIG_ATMEL_LCD
  51 #define CONFIG_ATMEL_LCD_RGB565
  52 /* board specific(not enough SRAM) */
  53 #define CONFIG_AT91SAM9G45_LCD_BASE             0x23E00000
  54
  55 /* LED */
  56 #define CONFIG_AT91_LED
  57 #define CONFIG_GREEN_LED        AT91_PIN_PD31   /* this is the user1 led */
  58
  59
  60 /*
  61  * BOOTP options
  62  */
  63 #define CONFIG_BOOTP_BOOTFILESIZE
  64 #define CONFIG_BOOTP_BOOTPATH
  65 #define CONFIG_BOOTP_GATEWAY
  66 #define CONFIG_BOOTP_HOSTNAME
  67
  68 /* Enable the watchdog */
  69 #define CONFIG_AT91SAM9_WATCHDOG
  70 #define CONFIG_HW_WATCHDOG
  71
  72 /*
  73  * Command line configuration.
  74  */
  75
  76 /* SDRAM */
  77 #define CONFIG_NR_DRAM_BANKS    2
  78 #define PHYS_SDRAM_1            ATMEL_BASE_CS1  /* on DDRSDRC1 */
  79 #define PHYS_SDRAM_1_SIZE       0x08000000      /* 128 MB */
  80 #define PHYS_SDRAM_2            ATMEL_BASE_CS6  /* on DDRSDRC0 */
  81 #define PHYS_SDRAM_2_SIZE       0x08000000      /* 128 MB */
  82 #define CONFIG_SYS_SDRAM_BASE   PHYS_SDRAM_1
  83
  84 #define CONFIG_SYS_INIT_SP_ADDR \
  85         (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
  86
  87 /* MMC */
  88
  89 #ifdef CONFIG_CMD_MMC
  90 #define CONFIG_GENERIC_ATMEL_MCI
  91 #endif
  92
  93 /* Ethernet */
  94 #define CONFIG_MACB
  95 #define CONFIG_RMII
  96 #define CONFIG_NET_RETRY_COUNT          20
  97 #define CONFIG_RESET_PHY_R
  98 #define CONFIG_AT91_WANTS_COMMON_PHY
  99
 100 /* USB */
 101 #define CONFIG_USB_EHCI_ATMEL
 102 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS      2
 103
 104 #define CONFIG_SYS_LOAD_ADDR            0x22000000      /* load address */
 105
 106 #define CONFIG_SYS_MEMTEST_START        CONFIG_SYS_SDRAM_BASE
 107 #define CONFIG_SYS_MEMTEST_END          0x23e00000
 108
 109 #ifdef CONFIG_SYS_USE_MMC
 110 /* bootstrap + u-boot + env + linux in mmc */
 111 #define FAT_ENV_INTERFACE       "mmc"
 112 /*
 113  * We don't specify the part number, if device 0 has partition table, it means
 114  * the first partition; it no partition table, then take whole device as a
 115  * FAT file system.
 116  */
 117 #define FAT_ENV_DEVICE_AND_PART "0"
 118 #define FAT_ENV_FILE            "uboot.env"
 119 #define CONFIG_ENV_IS_IN_FAT
 120 #define CONFIG_FAT_WRITE
 121 #define CONFIG_ENV_SIZE         0x4000
 122
 123 #define CONFIG_BOOTARGS         "console=ttyS0,115200 " \
 124                                 "root=/dev/mmcblk0p2 rw rootwait"
 125 #define CONFIG_BOOTCOMMAND      "fatload mmc 0:1 0x21000000 dtb; " \
 126                                 "fatload mmc 0:1 0x22000000 zImage; " \
 127                                 "bootz 0x22000000 - 0x21000000"
 128 #endif
 129
 130 #define CONFIG_SYS_CBSIZE       256
 131 #define CONFIG_SYS_MAXARGS      16
 132 #define CONFIG_SYS_PBSIZE       (CONFIG_SYS_CBSIZE  \
 133                                         + sizeof(CONFIG_SYS_PROMPT) + 16)
 134 #define CONFIG_SYS_LONGHELP
 135 #define CONFIG_CMDLINE_EDITING
 136 #define CONFIG_AUTO_COMPLETE
 137
 138 /*
 139  * Size of malloc() pool
 140  */
 141 #define CONFIG_SYS_MALLOC_LEN   ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
 142
 143 /* Defines for SPL */
 144 #define CONFIG_SPL_FRAMEWORK
 145 #define CONFIG_SPL_TEXT_BASE            0x300000
 146 #define CONFIG_SPL_MAX_SIZE             0x010000
 147 #define CONFIG_SPL_STACK                0x310000
 148
 149 #define CONFIG_SYS_MONITOR_LEN          0x80000
 150
 151 #ifdef CONFIG_SYS_USE_MMC
 152
 153 #define CONFIG_SPL_BSS_START_ADDR       0x20000000
 154 #define CONFIG_SPL_BSS_MAX_SIZE         0x00080000
 155 #define CONFIG_SYS_SPL_MALLOC_START     0x20080000
 156 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x00080000
 157
 158 #define CONFIG_SPL_LDSCRIPT     arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
 159 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION      1
 160 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME         "u-boot.img"
 161
 162 #define CONFIG_SPL_ATMEL_SIZE
 163 #define CONFIG_SYS_MASTER_CLOCK         132096000
 164 #define CONFIG_SYS_AT91_PLLA            0x20c73f03
 165 #define CONFIG_SYS_MCKR                 0x1301
 166 #define CONFIG_SYS_MCKR_CSS             0x1302
 167
 168 #endif
 169 #endif