include/configs/rpi.h

   1 /*
   2  * (C) Copyright 2012-2016 Stephen Warren
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0
   5  */
   6
   7 #ifndef __CONFIG_H
   8 #define __CONFIG_H
   9
  10 #include <linux/sizes.h>
  11 #include <asm/arch/timer.h>
  12
  13 #if defined(CONFIG_TARGET_RPI_2) || defined(CONFIG_TARGET_RPI_3_32B)
  14 #define CONFIG_SKIP_LOWLEVEL_INIT
  15 #endif
  16
  17 /* Architecture, CPU, etc.*/
  18 #define CONFIG_ARCH_CPU_INIT
  19
  20 /* Use SoC timer for AArch32, but architected timer for AArch64 */
  21 #ifndef CONFIG_ARM64
  22 #define CONFIG_SYS_TIMER_RATE           1000000
  23 #define CONFIG_SYS_TIMER_COUNTER        \
  24         (&((struct bcm2835_timer_regs *)BCM2835_TIMER_PHYSADDR)->clo)
  25 #endif
  26
  27 /*
  28  * 2835 is a SKU in a series for which the 2708 is the first or primary SoC,
  29  * so 2708 has historically been used rather than a dedicated 2835 ID.
  30  *
  31  * We don't define a machine type for bcm2709/bcm2836 since the RPi Foundation
  32  * chose to use someone else's previously registered machine ID (3139, MX51_GGC)
  33  * rather than obtaining a valid ID:-/
  34  *
  35  * For the bcm2837, hopefully a machine type is not needed, since everything
  36  * is DT.
  37  */
  38 #ifdef CONFIG_BCM2835
  39 #define CONFIG_MACH_TYPE                MACH_TYPE_BCM2708
  40 #endif
  41
  42 /* Memory layout */
  43 #define CONFIG_NR_DRAM_BANKS            1
  44 #define CONFIG_SYS_SDRAM_BASE           0x00000000
  45 #ifdef CONFIG_ARM64
  46 #define CONFIG_SYS_TEXT_BASE            0x00080000
  47 #else
  48 #define CONFIG_SYS_TEXT_BASE            0x00008000
  49 #endif
  50 #define CONFIG_SYS_UBOOT_BASE           CONFIG_SYS_TEXT_BASE
  51 /*
  52  * The board really has 256M. However, the VC (VideoCore co-processor) shares
  53  * the RAM, and uses a configurable portion at the top. We tell U-Boot that a
  54  * smaller amount of RAM is present in order to avoid stomping on the area
  55  * the VC uses.
  56  */
  57 #define CONFIG_SYS_SDRAM_SIZE           SZ_128M
  58 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_SDRAM_BASE + \
  59                                          CONFIG_SYS_SDRAM_SIZE - \
  60                                          GENERATED_GBL_DATA_SIZE)
  61 #define CONFIG_SYS_MALLOC_LEN           SZ_4M
  62 #define CONFIG_SYS_MEMTEST_START        0x00100000
  63 #define CONFIG_SYS_MEMTEST_END          0x00200000
  64 #define CONFIG_LOADADDR                 0x00200000
  65
  66 /* Devices */
  67 /* GPIO */
  68 #define CONFIG_BCM2835_GPIO
  69 /* LCD */
  70 #define CONFIG_LCD_DT_SIMPLEFB
  71 #define CONFIG_VIDEO_BCM2835
  72
  73 #ifdef CONFIG_CMD_USB
  74 #define CONFIG_TFTP_TSIZE
  75 #define CONFIG_MISC_INIT_R
  76 #endif
  77
  78 /* Console UART */
  79 #if defined (CONFIG_BCM2837) || defined(CONFIG_TARGET_RPI_0_W)
  80 #define CONFIG_BCM283X_MU_SERIAL
  81 #else
  82 #define CONFIG_PL01X_SERIAL
  83 #endif
  84
  85 /* Console configuration */
  86 #define CONFIG_SYS_CBSIZE               1024
  87
  88 /* Environment */
  89 #define CONFIG_ENV_SIZE                 SZ_16K
  90 #define CONFIG_ENV_VARS_UBOOT_CONFIG
  91 #define CONFIG_SYS_LOAD_ADDR            0x1000000
  92 #define CONFIG_PREBOOT                  "usb start"
  93
  94 /* Shell */
  95 #define CONFIG_CMDLINE_EDITING
  96
  97 /* ATAGs support for bootm/bootz */
  98 #define CONFIG_SETUP_MEMORY_TAGS
  99 #define CONFIG_CMDLINE_TAG
 100 #define CONFIG_INITRD_TAG
 101
 102 #include <config_distro_defaults.h>
 103
 104 /* Environment */
 105 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
 106 #define ENV_DEVICE_SETTINGS \
 107         "stdin=serial,usbkbd\0" \
 108         "stdout=serial,vidconsole\0" \
 109         "stderr=serial,vidconsole\0"
 110
 111 /*
 112  * Memory layout for where various images get loaded by boot scripts:
 113  *
 114  * I suspect address 0 is used as the SMP pen on the RPi2, so avoid this.
 115  *
 116  * fdt_addr_r simply shouldn't overlap anything else. However, the RPi's
 117  *   binary firmware loads a DT to address 0x100, so we choose this address to
 118  *   match it. This allows custom boot scripts to pass this DT on to Linux
 119  *   simply by not over-writing the data at this address. When using U-Boot,
 120  *   U-Boot (and scripts it executes) typicaly ignore the DT loaded by the FW
 121  *   and loads its own DT from disk (triggered by boot.scr or extlinux.conf).
 122  *
 123  * pxefile_addr_r can be pretty much anywhere that doesn't conflict with
 124  *   something else. Put it low in memory to avoid conflicts.
 125  *
 126  * kernel_addr_r must be within the first 128M of RAM in order for the
 127  *   kernel's CONFIG_AUTO_ZRELADDR option to work. Since the kernel will
 128  *   decompress itself to 0x8000 after the start of RAM, kernel_addr_r
 129  *   should not overlap that area, or the kernel will have to copy itself
 130  *   somewhere else before decompression. Similarly, the address of any other
 131  *   data passed to the kernel shouldn't overlap the start of RAM. Pushing
 132  *   this up to 16M allows for a sizable kernel to be decompressed below the
 133  *   compressed load address.
 134  *
 135  * scriptaddr can be pretty much anywhere that doesn't conflict with something
 136  *   else. Choosing 32M allows for the compressed kernel to be up to 16M.
 137  *
 138  * ramdisk_addr_r simply shouldn't overlap anything else. Choosing 33M allows
 139  *   for any boot script to be up to 1M, which is hopefully plenty.
 140  */
 141 #define ENV_MEM_LAYOUT_SETTINGS \
 142         "fdt_high=ffffffff\0" \
 143         "initrd_high=ffffffff\0" \
 144         "fdt_addr_r=0x00000100\0" \
 145         "pxefile_addr_r=0x00100000\0" \
 146         "kernel_addr_r=0x01000000\0" \
 147         "scriptaddr=0x02000000\0" \
 148         "ramdisk_addr_r=0x02100000\0" \
 149
 150 #define BOOT_TARGET_DEVICES(func) \
 151         func(MMC, mmc, 0) \
 152         func(USB, usb, 0) \
 153         func(PXE, pxe, na) \
 154         func(DHCP, dhcp, na)
 155 #include <config_distro_bootcmd.h>
 156
 157 #define CONFIG_EXTRA_ENV_SETTINGS \
 158         "dhcpuboot=usb start; dhcp u-boot.uimg; bootm\0" \
 159         ENV_DEVICE_SETTINGS \
 160         ENV_MEM_LAYOUT_SETTINGS \
 161         BOOTENV
 162
 163
 164 #endif