include/configs/sama5d2_ptc.h

   1 /*
   2  * Configuration settings for the SAMA5D2 PTC Engineering board.
   3  *
   4  * Copyright (C) 2016 Atmel
   5  *                    Wenyou Yang <wenyou.yang@atmel.com>
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 /* No NOR flash, this definition should put before common header */
  14 #define CONFIG_SYS_NO_FLASH
  15
  16 #include "at91-sama5_common.h"
  17
  18 /* serial console */
  19 #define CONFIG_ATMEL_USART
  20 #define CONFIG_USART_BASE               ATMEL_BASE_UART0
  21 #define CONFIG_USART_ID                 ATMEL_ID_UART0
  22
  23 #define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_DDRCS
  24 #define CONFIG_SYS_SDRAM_SIZE           0x20000000
  25
  26 #ifdef CONFIG_SPL_BUILD
  27 #define CONFIG_SYS_INIT_SP_ADDR         0x210000
  28 #else
  29 #define CONFIG_SYS_INIT_SP_ADDR \
  30         (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
  31 #endif
  32
  33 #define CONFIG_SYS_LOAD_ADDR            0x22000000 /* load address */
  34
  35 #undef CONFIG_AT91_GPIO
  36 #define CONFIG_ATMEL_PIO4
  37
  38 /* SDRAM */
  39 #define CONFIG_NR_DRAM_BANKS            1
  40
  41 /* SerialFlash */
  42 #ifdef CONFIG_CMD_SF
  43 #define CONFIG_ATMEL_SPI
  44 #define CONFIG_SPI_FLASH_ATMEL
  45 #define CONFIG_SF_DEFAULT_BUS           0
  46 #define CONFIG_SF_DEFAULT_CS            0
  47 #define CONFIG_SF_DEFAULT_SPEED         30000000
  48 #endif
  49
  50 /* NAND flash */
  51 #define CONFIG_CMD_NAND
  52
  53 #ifdef CONFIG_CMD_NAND
  54 #define CONFIG_NAND_ATMEL
  55 #define CONFIG_SYS_MAX_NAND_DEVICE      1
  56 #define CONFIG_SYS_NAND_BASE            ATMEL_BASE_CS3
  57 /* our ALE is AD21 */
  58 #define CONFIG_SYS_NAND_MASK_ALE        (1 << 21)
  59 /* our CLE is AD22 */
  60 #define CONFIG_SYS_NAND_MASK_CLE        (1 << 22)
  61 #define CONFIG_SYS_NAND_ONFI_DETECTION
  62 /* PMECC & PMERRLOC */
  63 #define CONFIG_ATMEL_NAND_HWECC
  64 #define CONFIG_ATMEL_NAND_HW_PMECC
  65 #define CONFIG_CMD_NAND_TRIMFFS
  66 #endif
  67
  68 /* USB */
  69 #define CONFIG_CMD_USB
  70
  71 #ifdef CONFIG_CMD_USB
  72 #define CONFIG_USB_EHCI
  73 #define CONFIG_USB_EHCI_ATMEL
  74 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS      3
  75 #endif
  76
  77 /* USB device */
  78 #define CONFIG_USB_GADGET
  79 #define CONFIG_USB_GADGET_DUALSPEED
  80 #define CONFIG_USB_GADGET_ATMEL_USBA
  81 #define CONFIG_USB_ETHER
  82 #define CONFIG_USB_ETH_RNDIS
  83 #define CONFIG_USBNET_MANUFACTURER      "Atmel SAMA5D2_PTC"
  84
  85 #if defined(CONFIG_CMD_USB)
  86 #define CONFIG_CMD_FAT
  87 #define CONFIG_DOS_PARTITION
  88 #endif
  89
  90 /* Ethernet Hardware */
  91 #define CONFIG_MACB
  92 #define CONFIG_RMII
  93 #define CONFIG_NET_RETRY_COUNT          20
  94 #define CONFIG_MACB_SEARCH_PHY
  95
  96 #ifdef CONFIG_SYS_USE_NANDFLASH
  97 #undef CONFIG_ENV_OFFSET
  98 #undef CONFIG_ENV_OFFSET_REDUND
  99 #undef CONFIG_BOOTCOMMAND
 100 /* u-boot env in nand flash */
 101 #define CONFIG_ENV_IS_IN_NAND
 102 #define CONFIG_ENV_OFFSET               0x200000
 103 #define CONFIG_ENV_OFFSET_REDUND        0x400000
 104 #define CONFIG_BOOTCOMMAND              "nand read 0x21000000 0xb80000 0x80000;"        \
 105                                         "nand read 0x22000000 0x600000 0x600000;"       \
 106                                         "bootz 0x22000000 - 0x21000000"
 107 #endif
 108
 109 #undef CONFIG_BOOTARGS
 110 #define CONFIG_BOOTARGS                                                 \
 111         "console=ttyS0,57600 earlyprintk "                              \
 112         "mtdparts=atmel_nand:6M(bootstrap)ro, 6M(kernel)ro,-(rootfs) "  \
 113         "rootfstype=ubifs ubi.mtd=2 root=ubi0:rootfs"
 114
 115 /* SPL */
 116 #define CONFIG_SPL_FRAMEWORK
 117 #define CONFIG_SPL_TEXT_BASE            0x200000
 118 #define CONFIG_SPL_MAX_SIZE             0x10000
 119 #define CONFIG_SPL_BSS_START_ADDR       0x20000000
 120 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
 121 #define CONFIG_SYS_SPL_MALLOC_START     0x20080000
 122 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x80000
 123
 124 #define CONFIG_SPL_BOARD_INIT
 125 #define CONFIG_SYS_MONITOR_LEN          (512 << 10)
 126
 127 #ifdef CONFIG_SYS_USE_SERIALFLASH
 128 #define CONFIG_SPL_SPI_SUPPORT
 129 #define CONFIG_SPL_SPI_LOAD
 130 #define CONFIG_SYS_SPI_U_BOOT_OFFS      0x8000
 131
 132 #elif CONFIG_SYS_USE_NANDFLASH
 133 #define CONFIG_SPL_NAND_DRIVERS
 134 #define CONFIG_SPL_NAND_BASE
 135 #define CONFIG_PMECC_CAP                8
 136 #define CONFIG_PMECC_SECTOR_SIZE        512
 137 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x40000
 138 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 139 #define CONFIG_SYS_NAND_PAGE_SIZE       0x1000
 140 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 141 #define CONFIG_SYS_NAND_OOBSIZE         224
 142 #define CONFIG_SYS_NAND_BLOCK_SIZE      0x40000
 143 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   0x0
 144 #define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
 145 #endif
 146
 147 #endif