include/configs/sbc8349.h

   1 /*
   2  * WindRiver SBC8349 U-Boot configuration file.
   3  * Copyright (c) 2006, 2007 Wind River Systems, Inc.
   4  *
   5  * Paul Gortmaker <paul.gortmaker@windriver.com>
   6  * Based on the MPC8349EMDS config.
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 /*
  12  * sbc8349 board configuration file.
  13  */
  14
  15 #ifndef __CONFIG_H
  16 #define __CONFIG_H
  17
  18 #define CONFIG_DISPLAY_BOARDINFO
  19
  20 /*
  21  * High Level Configuration Options
  22  */
  23 #define CONFIG_E300             1       /* E300 Family */
  24 #define CONFIG_MPC834x          1       /* MPC834x family */
  25 #define CONFIG_MPC8349          1       /* MPC8349 specific */
  26 #define CONFIG_SBC8349          1       /* WRS SBC8349 board specific */
  27
  28 #define CONFIG_SYS_TEXT_BASE    0xFF800000
  29
  30 /* Don't enable PCI2 on sbc834x - it doesn't exist physically. */
  31 #undef CONFIG_MPC83XX_PCI2              /* support for 2nd PCI controller */
  32
  33 /*
  34  * The default if PCI isn't enabled, or if no PCI clk setting is given
  35  * is 66MHz; this is what the board defaults to when the PCI slot is
  36  * physically empty.  The board will automatically (i.e w/o jumpers)
  37  * clock down to 33MHz if you insert a 33MHz PCI card.
  38  */
  39 #ifdef CONFIG_PCI_33M
  40 #define CONFIG_83XX_CLKIN       33000000        /* in Hz */
  41 #else   /* 66M */
  42 #define CONFIG_83XX_CLKIN       66000000        /* in Hz */
  43 #endif
  44
  45 #ifndef CONFIG_SYS_CLK_FREQ
  46 #ifdef CONFIG_PCI_33M
  47 #define CONFIG_SYS_CLK_FREQ     33000000
  48 #define HRCWL_CSB_TO_CLKIN      HRCWL_CSB_TO_CLKIN_8X1
  49 #else   /* 66M */
  50 #define CONFIG_SYS_CLK_FREQ     66000000
  51 #define HRCWL_CSB_TO_CLKIN      HRCWL_CSB_TO_CLKIN_4X1
  52 #endif
  53 #endif
  54
  55 #undef CONFIG_BOARD_EARLY_INIT_F                /* call board_pre_init */
  56
  57 #define CONFIG_SYS_IMMR         0xE0000000
  58
  59 #undef CONFIG_SYS_DRAM_TEST             /* memory test, takes time */
  60 #define CONFIG_SYS_MEMTEST_START        0x00000000      /* memtest region */
  61 #define CONFIG_SYS_MEMTEST_END          0x00100000
  62
  63 /*
  64  * DDR Setup
  65  */
  66 #undef CONFIG_DDR_ECC                   /* only for ECC DDR module */
  67 #undef CONFIG_DDR_ECC_CMD               /* use DDR ECC user commands */
  68 #define CONFIG_SPD_EEPROM               /* use SPD EEPROM for DDR setup*/
  69 #define CONFIG_SYS_83XX_DDR_USES_CS0    /* WRS; Fsl board uses CS2/CS3 */
  70
  71 /*
  72  * 32-bit data path mode.
  73  *
  74  * Please note that using this mode for devices with the real density of 64-bit
  75  * effectively reduces the amount of available memory due to the effect of
  76  * wrapping around while translating address to row/columns, for example in the
  77  * 256MB module the upper 128MB get aliased with contents of the lower
  78  * 128MB); normally this define should be used for devices with real 32-bit
  79  * data path.
  80  */
  81 #undef CONFIG_DDR_32BIT
  82
  83 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory*/
  84 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
  85 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
  86 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   (DDR_SDRAM_CLK_CNTL_SS_EN | \
  87                                 DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
  88 #define CONFIG_DDR_2T_TIMING
  89
  90 #if defined(CONFIG_SPD_EEPROM)
  91 /*
  92  * Determine DDR configuration from I2C interface.
  93  */
  94 #define SPD_EEPROM_ADDRESS      0x52            /* DDR DIMM */
  95
  96 #else
  97 /*
  98  * Manually set up DDR parameters
  99  * NB: manual DDR setup untested on sbc834x
 100  */
 101 #define CONFIG_SYS_DDR_SIZE             256             /* MB */
 102 #define CONFIG_SYS_DDR_CS2_CONFIG       (CSCONFIG_EN \
 103                                         | CSCONFIG_ROW_BIT_13 \
 104                                         | CSCONFIG_COL_BIT_10)
 105 #define CONFIG_SYS_DDR_TIMING_1 0x36332321
 106 #define CONFIG_SYS_DDR_TIMING_2 0x00000800      /* P9-45,may need tuning */
 107 #define CONFIG_SYS_DDR_CONTROL  0xc2000000      /* unbuffered,no DYN_PWR */
 108 #define CONFIG_SYS_DDR_INTERVAL 0x04060100      /* autocharge,no open page */
 109
 110 #if defined(CONFIG_DDR_32BIT)
 111 /* set burst length to 8 for 32-bit data path */
 112                                 /* DLL,normal,seq,4/2.5, 8 burst len */
 113 #define CONFIG_SYS_DDR_MODE     0x00000023
 114 #else
 115 /* the default burst length is 4 - for 64-bit data path */
 116                                 /* DLL,normal,seq,4/2.5, 4 burst len */
 117 #define CONFIG_SYS_DDR_MODE     0x00000022
 118 #endif
 119 #endif
 120
 121 /*
 122  * SDRAM on the Local Bus
 123  */
 124 #define CONFIG_SYS_LBC_SDRAM_BASE       0xF0000000      /* Localbus SDRAM */
 125 #define CONFIG_SYS_LBC_SDRAM_SIZE       64              /* LBC SDRAM is 64MB */
 126
 127 /*
 128  * FLASH on the Local Bus
 129  */
 130 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
 131 #define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
 132 #define CONFIG_SYS_FLASH_BASE           0xFF800000      /* start of FLASH   */
 133 #define CONFIG_SYS_FLASH_SIZE           8               /* flash size in MB */
 134 /* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
 135
 136 #define CONFIG_SYS_BR0_PRELIM           (CONFIG_SYS_FLASH_BASE \
 137                                         | BR_PS_16      /* 16 bit port */ \
 138                                         | BR_MS_GPCM    /* MSEL = GPCM */ \
 139                                         | BR_V)         /* valid */
 140
 141 #define CONFIG_SYS_OR0_PRELIM           (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
 142                                         | OR_GPCM_XAM \
 143                                         | OR_GPCM_CSNT \
 144                                         | OR_GPCM_ACS_DIV2 \
 145                                         | OR_GPCM_XACS \
 146                                         | OR_GPCM_SCY_15 \
 147                                         | OR_GPCM_TRLX_SET \
 148                                         | OR_GPCM_EHTR_SET \
 149                                         | OR_GPCM_EAD)
 150                                         /* 0xFF806FF7 */
 151
 152                                         /* window base at flash base */
 153 #define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
 154 #define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_8MB)
 155
 156 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 157 #define CONFIG_SYS_MAX_FLASH_SECT       64      /* sectors per device */
 158
 159 #undef CONFIG_SYS_FLASH_CHECKSUM
 160 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 161 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 162
 163 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 164
 165 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 166 #define CONFIG_SYS_RAMBOOT
 167 #else
 168 #undef  CONFIG_SYS_RAMBOOT
 169 #endif
 170
 171 #define CONFIG_SYS_INIT_RAM_LOCK        1
 172                                         /* Initial RAM address */
 173 #define CONFIG_SYS_INIT_RAM_ADDR        0xFD000000
 174                                         /* Size of used area in RAM*/
 175 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000
 176
 177 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 178                         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 179 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 180
 181 #define CONFIG_SYS_MONITOR_LEN  (256 * 1024)    /* Reserve 256 kB for Mon */
 182 #define CONFIG_SYS_MALLOC_LEN   (256 * 1024)    /* Reserved for malloc */
 183
 184 /*
 185  * Local Bus LCRR and LBCR regs
 186  *    LCRR:  DLL bypass, Clock divider is 4
 187  * External Local Bus rate is
 188  *    CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
 189  */
 190 #define CONFIG_SYS_LCRR_DBYP    LCRR_DBYP
 191 #define CONFIG_SYS_LCRR_CLKDIV  LCRR_CLKDIV_4
 192 #define CONFIG_SYS_LBC_LBCR     0x00000000
 193
 194 #undef CONFIG_SYS_LB_SDRAM      /* if board has SDRAM on local bus */
 195
 196 #ifdef CONFIG_SYS_LB_SDRAM
 197 /* Local bus BR2, OR2 definition for SDRAM if soldered on the board*/
 198 /*
 199  * Base Register 2 and Option Register 2 configure SDRAM.
 200  * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
 201  *
 202  * For BR2, need:
 203  *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
 204  *    port-size = 32-bits = BR2[19:20] = 11
 205  *    no parity checking = BR2[21:22] = 00
 206  *    SDRAM for MSEL = BR2[24:26] = 011
 207  *    Valid = BR[31] = 1
 208  *
 209  * 0    4    8    12   16   20   24   28
 210  * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861
 211  */
 212
 213 #define CONFIG_SYS_BR2_PRELIM           (CONFIG_SYS_LBC_SDRAM_BASE \
 214                                         | BR_PS_32 \
 215                                         | BR_MS_SDRAM \
 216                                         | BR_V)
 217                                         /* 0xF0001861 */
 218 #define CONFIG_SYS_LBLAWBAR2_PRELIM     CONFIG_SYS_LBC_SDRAM_BASE
 219 #define CONFIG_SYS_LBLAWAR2_PRELIM      (LBLAWAR_EN | LBLAWAR_64MB)
 220
 221 /*
 222  * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
 223  *
 224  * For OR2, need:
 225  *    64MB mask for AM, OR2[0:7] = 1111 1100
 226  *                 XAM, OR2[17:18] = 11
 227  *    9 columns OR2[19-21] = 010
 228  *    13 rows   OR2[23-25] = 100
 229  *    EAD set for extra time OR[31] = 1
 230  *
 231  * 0    4    8    12   16   20   24   28
 232  * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901
 233  */
 234
 235 #define CONFIG_SYS_OR2_PRELIM   (MEG_TO_AM(CONFIG_SYS_LBC_SDRAM_SIZE) \
 236                         | OR_SDRAM_XAM \
 237                         | ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \
 238                         | ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \
 239                         | OR_SDRAM_EAD)
 240                         /* 0xFC006901 */
 241
 242                                 /* LB sdram refresh timer, about 6us */
 243 #define CONFIG_SYS_LBC_LSRT     0x32000000
 244                                 /* LB refresh timer prescal, 266MHz/32 */
 245 #define CONFIG_SYS_LBC_MRTPR    0x20000000
 246
 247 #define CONFIG_SYS_LBC_LSDMR_COMMON     (LSDMR_RFEN \
 248                                         | LSDMR_BSMA1516 \
 249                                         | LSDMR_RFCR8 \
 250                                         | LSDMR_PRETOACT6 \
 251                                         | LSDMR_ACTTORW3 \
 252                                         | LSDMR_BL8 \
 253                                         | LSDMR_WRC3 \
 254                                         | LSDMR_CL3)
 255
 256 /*
 257  * SDRAM Controller configuration sequence.
 258  */
 259 #define CONFIG_SYS_LBC_LSDMR_1  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
 260 #define CONFIG_SYS_LBC_LSDMR_2  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
 261 #define CONFIG_SYS_LBC_LSDMR_3  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
 262 #define CONFIG_SYS_LBC_LSDMR_4  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
 263 #define CONFIG_SYS_LBC_LSDMR_5  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
 264 #endif
 265
 266 /*
 267  * Serial Port
 268  */
 269 #define CONFIG_CONS_INDEX     1
 270 #define CONFIG_SYS_NS16550_SERIAL
 271 #define CONFIG_SYS_NS16550_REG_SIZE    1
 272 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 273
 274 #define CONFIG_SYS_BAUDRATE_TABLE  \
 275                 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 276
 277 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_IMMR+0x4500)
 278 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_IMMR+0x4600)
 279
 280 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 281 #define CONFIG_AUTO_COMPLETE            /* add autocompletion support   */
 282
 283 /* I2C */
 284 #define CONFIG_SYS_I2C
 285 #define CONFIG_SYS_I2C_FSL
 286 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 287 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 288 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 289 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 290 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 291 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 292 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69}, {1, 0x69} }
 293 /* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
 294
 295 /* TSEC */
 296 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 297 #define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
 298 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 299 #define CONFIG_SYS_TSEC2        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
 300
 301 /*
 302  * General PCI
 303  * Addresses are mapped 1-1.
 304  */
 305 #define CONFIG_SYS_PCI1_MEM_BASE        0x80000000
 306 #define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BASE
 307 #define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000      /* 256M */
 308 #define CONFIG_SYS_PCI1_MMIO_BASE       0x90000000
 309 #define CONFIG_SYS_PCI1_MMIO_PHYS       CONFIG_SYS_PCI1_MMIO_BASE
 310 #define CONFIG_SYS_PCI1_MMIO_SIZE       0x10000000      /* 256M */
 311 #define CONFIG_SYS_PCI1_IO_BASE         0x00000000
 312 #define CONFIG_SYS_PCI1_IO_PHYS         0xE2000000
 313 #define CONFIG_SYS_PCI1_IO_SIZE         0x00100000      /* 1M */
 314
 315 #define CONFIG_SYS_PCI2_MEM_BASE        0xA0000000
 316 #define CONFIG_SYS_PCI2_MEM_PHYS        CONFIG_SYS_PCI2_MEM_BASE
 317 #define CONFIG_SYS_PCI2_MEM_SIZE        0x10000000      /* 256M */
 318 #define CONFIG_SYS_PCI2_MMIO_BASE       0xB0000000
 319 #define CONFIG_SYS_PCI2_MMIO_PHYS       CONFIG_SYS_PCI2_MMIO_BASE
 320 #define CONFIG_SYS_PCI2_MMIO_SIZE       0x10000000      /* 256M */
 321 #define CONFIG_SYS_PCI2_IO_BASE         0x00000000
 322 #define CONFIG_SYS_PCI2_IO_PHYS         0xE2100000
 323 #define CONFIG_SYS_PCI2_IO_SIZE         0x00100000      /* 1M */
 324
 325 #if defined(CONFIG_PCI)
 326
 327 #define PCI_64BIT
 328 #define PCI_ONE_PCI1
 329 #if defined(PCI_64BIT)
 330 #undef PCI_ALL_PCI1
 331 #undef PCI_TWO_PCI1
 332 #undef PCI_ONE_PCI1
 333 #endif
 334
 335 #define CONFIG_PCI_PNP          /* do pci plug-and-play */
 336
 337 #undef CONFIG_EEPRO100
 338 #undef CONFIG_TULIP
 339
 340 #if !defined(CONFIG_PCI_PNP)
 341         #define PCI_ENET0_IOADDR        0xFIXME
 342         #define PCI_ENET0_MEMADDR       0xFIXME
 343         #define PCI_IDSEL_NUMBER        0xFIXME
 344 #endif
 345
 346 #undef CONFIG_PCI_SCAN_SHOW             /* show pci devices on startup */
 347 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
 348
 349 #endif  /* CONFIG_PCI */
 350
 351 /*
 352  * TSEC configuration
 353  */
 354 #define CONFIG_TSEC_ENET                /* TSEC ethernet support */
 355
 356 #if defined(CONFIG_TSEC_ENET)
 357
 358 #define CONFIG_TSEC1    1
 359 #define CONFIG_TSEC1_NAME       "TSEC0"
 360 #define CONFIG_TSEC2    1
 361 #define CONFIG_TSEC2_NAME       "TSEC1"
 362 #define CONFIG_PHY_BCM5421S     1
 363 #define TSEC1_PHY_ADDR          0x19
 364 #define TSEC2_PHY_ADDR          0x1a
 365 #define TSEC1_PHYIDX            0
 366 #define TSEC2_PHYIDX            0
 367 #define TSEC1_FLAGS             TSEC_GIGABIT
 368 #define TSEC2_FLAGS             TSEC_GIGABIT
 369
 370 /* Options are: TSEC[0-1] */
 371 #define CONFIG_ETHPRIME         "TSEC0"
 372
 373 #endif  /* CONFIG_TSEC_ENET */
 374
 375 /*
 376  * Environment
 377  */
 378 #ifndef CONFIG_SYS_RAMBOOT
 379         #define CONFIG_ENV_IS_IN_FLASH  1
 380         #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + 0x40000)
 381         #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K(one sector) for env */
 382         #define CONFIG_ENV_SIZE         0x2000
 383
 384 /* Address and size of Redundant Environment Sector     */
 385 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 386 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 387
 388 #else
 389         #define CONFIG_SYS_NO_FLASH     1       /* Flash is not usable now */
 390         #define CONFIG_ENV_IS_NOWHERE   1       /* Store ENV in memory only */
 391         #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 392         #define CONFIG_ENV_SIZE         0x2000
 393 #endif
 394
 395 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 396 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 397
 398 /*
 399  * BOOTP options
 400  */
 401 #define CONFIG_BOOTP_BOOTFILESIZE
 402 #define CONFIG_BOOTP_BOOTPATH
 403 #define CONFIG_BOOTP_GATEWAY
 404 #define CONFIG_BOOTP_HOSTNAME
 405
 406 /*
 407  * Command line configuration.
 408  */
 409 #define CONFIG_CMD_MII
 410
 411 #if defined(CONFIG_PCI)
 412     #define CONFIG_CMD_PCI
 413 #endif
 414
 415 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 416
 417 /*
 418  * Miscellaneous configurable options
 419  */
 420 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 421 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 422
 423 #if defined(CONFIG_CMD_KGDB)
 424         #define CONFIG_SYS_CBSIZE       1024    /* Console I/O Buffer Size */
 425 #else
 426         #define CONFIG_SYS_CBSIZE       256     /* Console I/O Buffer Size */
 427 #endif
 428
 429                                 /* Print Buffer Size */
 430 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 431 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 432                                 /* Boot Argument Buffer Size */
 433 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 434
 435 /*
 436  * For booting Linux, the board info and command line data
 437  * have to be in the first 256 MB of memory, since this is
 438  * the maximum mapped by the Linux kernel during initialization.
 439  */
 440                                 /* Initial Memory map for Linux*/
 441 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20)
 442
 443 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
 444
 445 #if 1 /*528/264*/
 446 #define CONFIG_SYS_HRCW_LOW (\
 447         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 448         HRCWL_DDR_TO_SCB_CLK_1X1 |\
 449         HRCWL_CSB_TO_CLKIN |\
 450         HRCWL_VCO_1X2 |\
 451         HRCWL_CORE_TO_CSB_2X1)
 452 #elif 0 /*396/132*/
 453 #define CONFIG_SYS_HRCW_LOW (\
 454         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 455         HRCWL_DDR_TO_SCB_CLK_1X1 |\
 456         HRCWL_CSB_TO_CLKIN |\
 457         HRCWL_VCO_1X4 |\
 458         HRCWL_CORE_TO_CSB_3X1)
 459 #elif 0 /*264/132*/
 460 #define CONFIG_SYS_HRCW_LOW (\
 461         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 462         HRCWL_DDR_TO_SCB_CLK_1X1 |\
 463         HRCWL_CSB_TO_CLKIN |\
 464         HRCWL_VCO_1X4 |\
 465         HRCWL_CORE_TO_CSB_2X1)
 466 #elif 0 /*132/132*/
 467 #define CONFIG_SYS_HRCW_LOW (\
 468         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 469         HRCWL_DDR_TO_SCB_CLK_1X1 |\
 470         HRCWL_CSB_TO_CLKIN |\
 471         HRCWL_VCO_1X4 |\
 472         HRCWL_CORE_TO_CSB_1X1)
 473 #elif 0 /*264/264 */
 474 #define CONFIG_SYS_HRCW_LOW (\
 475         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 476         HRCWL_DDR_TO_SCB_CLK_1X1 |\
 477         HRCWL_CSB_TO_CLKIN |\
 478         HRCWL_VCO_1X4 |\
 479         HRCWL_CORE_TO_CSB_1X1)
 480 #endif
 481
 482 #if defined(PCI_64BIT)
 483 #define CONFIG_SYS_HRCW_HIGH (\
 484         HRCWH_PCI_HOST |\
 485         HRCWH_64_BIT_PCI |\
 486         HRCWH_PCI1_ARBITER_ENABLE |\
 487         HRCWH_PCI2_ARBITER_DISABLE |\
 488         HRCWH_CORE_ENABLE |\
 489         HRCWH_FROM_0X00000100 |\
 490         HRCWH_BOOTSEQ_DISABLE |\
 491         HRCWH_SW_WATCHDOG_DISABLE |\
 492         HRCWH_ROM_LOC_LOCAL_16BIT |\
 493         HRCWH_TSEC1M_IN_GMII |\
 494         HRCWH_TSEC2M_IN_GMII)
 495 #else
 496 #define CONFIG_SYS_HRCW_HIGH (\
 497         HRCWH_PCI_HOST |\
 498         HRCWH_32_BIT_PCI |\
 499         HRCWH_PCI1_ARBITER_ENABLE |\
 500         HRCWH_PCI2_ARBITER_ENABLE |\
 501         HRCWH_CORE_ENABLE |\
 502         HRCWH_FROM_0X00000100 |\
 503         HRCWH_BOOTSEQ_DISABLE |\
 504         HRCWH_SW_WATCHDOG_DISABLE |\
 505         HRCWH_ROM_LOC_LOCAL_16BIT |\
 506         HRCWH_TSEC1M_IN_GMII |\
 507         HRCWH_TSEC2M_IN_GMII)
 508 #endif
 509
 510 /* System IO Config */
 511 #define CONFIG_SYS_SICRH 0
 512 #define CONFIG_SYS_SICRL SICRL_LDP_A
 513
 514 #define CONFIG_SYS_HID0_INIT    0x000000000
 515 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK \
 516                                 | HID0_ENABLE_INSTRUCTION_CACHE)
 517
 518 /* #define CONFIG_SYS_HID0_FINAL        (\
 519         HID0_ENABLE_INSTRUCTION_CACHE |\
 520         HID0_ENABLE_M_BIT |\
 521         HID0_ENABLE_ADDRESS_BROADCAST) */
 522
 523 #define CONFIG_SYS_HID2 HID2_HBE
 524
 525 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
 526
 527 /* DDR @ 0x00000000 */
 528 #define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE \
 529                                 | BATL_PP_RW \
 530                                 | BATL_MEMCOHERENCE)
 531 #define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE \
 532                                 | BATU_BL_256M \
 533                                 | BATU_VS \
 534                                 | BATU_VP)
 535
 536 /* PCI @ 0x80000000 */
 537 #ifdef CONFIG_PCI
 538 #define CONFIG_PCI_INDIRECT_BRIDGE
 539 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_PCI1_MEM_BASE \
 540                                 | BATL_PP_RW \
 541                                 | BATL_MEMCOHERENCE)
 542 #define CONFIG_SYS_IBAT1U       (CONFIG_SYS_PCI1_MEM_BASE \
 543                                 | BATU_BL_256M \
 544                                 | BATU_VS \
 545                                 | BATU_VP)
 546 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_PCI1_MMIO_BASE \
 547                                 | BATL_PP_RW \
 548                                 | BATL_CACHEINHIBIT \
 549                                 | BATL_GUARDEDSTORAGE)
 550 #define CONFIG_SYS_IBAT2U       (CONFIG_SYS_PCI1_MMIO_BASE \
 551                                 | BATU_BL_256M \
 552                                 | BATU_VS \
 553                                 | BATU_VP)
 554 #else
 555 #define CONFIG_SYS_IBAT1L       (0)
 556 #define CONFIG_SYS_IBAT1U       (0)
 557 #define CONFIG_SYS_IBAT2L       (0)
 558 #define CONFIG_SYS_IBAT2U       (0)
 559 #endif
 560
 561 #ifdef CONFIG_MPC83XX_PCI2
 562 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_PCI2_MEM_BASE \
 563                                 | BATL_PP_RW \
 564                                 | BATL_MEMCOHERENCE)
 565 #define CONFIG_SYS_IBAT3U       (CONFIG_SYS_PCI2_MEM_BASE \
 566                                 | BATU_BL_256M \
 567                                 | BATU_VS \
 568                                 | BATU_VP)
 569 #define CONFIG_SYS_IBAT4L       (CONFIG_SYS_PCI2_MMIO_BASE \
 570                                 | BATL_PP_RW \
 571                                 | BATL_CACHEINHIBIT \
 572                                 | BATL_GUARDEDSTORAGE)
 573 #define CONFIG_SYS_IBAT4U       (CONFIG_SYS_PCI2_MMIO_BASE \
 574                                 | BATU_BL_256M \
 575                                 | BATU_VS \
 576                                 | BATU_VP)
 577 #else
 578 #define CONFIG_SYS_IBAT3L       (0)
 579 #define CONFIG_SYS_IBAT3U       (0)
 580 #define CONFIG_SYS_IBAT4L       (0)
 581 #define CONFIG_SYS_IBAT4U       (0)
 582 #endif
 583
 584 /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
 585 #define CONFIG_SYS_IBAT5L       (CONFIG_SYS_IMMR \
 586                                 | BATL_PP_RW \
 587                                 | BATL_CACHEINHIBIT \
 588                                 | BATL_GUARDEDSTORAGE)
 589 #define CONFIG_SYS_IBAT5U       (CONFIG_SYS_IMMR \
 590                                 | BATU_BL_256M \
 591                                 | BATU_VS \
 592                                 | BATU_VP)
 593
 594 /* LBC SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
 595 #define CONFIG_SYS_IBAT6L       (CONFIG_SYS_LBC_SDRAM_BASE \
 596                                 | BATL_PP_RW \
 597                                 | BATL_MEMCOHERENCE \
 598                                 | BATL_GUARDEDSTORAGE)
 599 #define CONFIG_SYS_IBAT6U       (CONFIG_SYS_LBC_SDRAM_BASE \
 600                                 | BATU_BL_256M \
 601                                 | BATU_VS \
 602                                 | BATU_VP)
 603
 604 #define CONFIG_SYS_IBAT7L       (0)
 605 #define CONFIG_SYS_IBAT7U       (0)
 606
 607 #define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
 608 #define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
 609 #define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
 610 #define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
 611 #define CONFIG_SYS_DBAT2L       CONFIG_SYS_IBAT2L
 612 #define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
 613 #define CONFIG_SYS_DBAT3L       CONFIG_SYS_IBAT3L
 614 #define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
 615 #define CONFIG_SYS_DBAT4L       CONFIG_SYS_IBAT4L
 616 #define CONFIG_SYS_DBAT4U       CONFIG_SYS_IBAT4U
 617 #define CONFIG_SYS_DBAT5L       CONFIG_SYS_IBAT5L
 618 #define CONFIG_SYS_DBAT5U       CONFIG_SYS_IBAT5U
 619 #define CONFIG_SYS_DBAT6L       CONFIG_SYS_IBAT6L
 620 #define CONFIG_SYS_DBAT6U       CONFIG_SYS_IBAT6U
 621 #define CONFIG_SYS_DBAT7L       CONFIG_SYS_IBAT7L
 622 #define CONFIG_SYS_DBAT7U       CONFIG_SYS_IBAT7U
 623
 624 #if defined(CONFIG_CMD_KGDB)
 625 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 626 #endif
 627
 628 /*
 629  * Environment Configuration
 630  */
 631 #define CONFIG_ENV_OVERWRITE
 632
 633 #if defined(CONFIG_TSEC_ENET)
 634 #define CONFIG_HAS_ETH0
 635 #define CONFIG_HAS_ETH1
 636 #endif
 637
 638 #define CONFIG_HOSTNAME         SBC8349
 639 #define CONFIG_ROOTPATH         "/tftpboot/rootfs"
 640 #define CONFIG_BOOTFILE         "uImage"
 641
 642                                 /* default location for tftp and bootm */
 643 #define CONFIG_LOADADDR         800000
 644
 645 #define CONFIG_BOOTDELAY        6       /* -1 disables auto-boot */
 646 #undef  CONFIG_BOOTARGS         /* the boot command will set bootargs */
 647
 648 #define CONFIG_BAUDRATE  115200
 649
 650 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 651         "netdev=eth0\0"                                                 \
 652         "hostname=sbc8349\0"                                            \
 653         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 654                 "nfsroot=${serverip}:${rootpath}\0"                     \
 655         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 656         "addip=setenv bootargs ${bootargs} "                            \
 657                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 658                 ":${hostname}:${netdev}:off panic=1\0"                  \
 659         "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
 660         "flash_nfs=run nfsargs addip addtty;"                           \
 661                 "bootm ${kernel_addr}\0"                                \
 662         "flash_self=run ramargs addip addtty;"                          \
 663                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 664         "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
 665                 "bootm\0"                                               \
 666         "load=tftp 100000 /tftpboot/sbc8349/u-boot.bin\0"               \
 667         "update=protect off ff800000 ff83ffff; "                        \
 668                 "era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \
 669         "upd=run load update\0"                                         \
 670         "fdtaddr=780000\0"                                              \
 671         "fdtfile=sbc8349.dtb\0"                                         \
 672         ""
 673
 674 #define CONFIG_NFSBOOTCOMMAND                                           \
 675         "setenv bootargs root=/dev/nfs rw "                             \
 676                 "nfsroot=$serverip:$rootpath "                          \
 677                 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"   \
 678                                                         "$netdev:off "  \
 679                 "console=$consoledev,$baudrate $othbootargs;"           \
 680         "tftp $loadaddr $bootfile;"                                     \
 681         "tftp $fdtaddr $fdtfile;"                                       \
 682         "bootm $loadaddr - $fdtaddr"
 683
 684 #define CONFIG_RAMBOOTCOMMAND                                           \
 685         "setenv bootargs root=/dev/ram rw "                             \
 686                 "console=$consoledev,$baudrate $othbootargs;"           \
 687         "tftp $ramdiskaddr $ramdiskfile;"                               \
 688         "tftp $loadaddr $bootfile;"                                     \
 689         "tftp $fdtaddr $fdtfile;"                                       \
 690         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 691
 692 #define CONFIG_BOOTCOMMAND      "run flash_self"
 693
 694 #endif  /* __CONFIG_H */