include/configs/tam3517-common.h

   1 /*
   2  * Copyright (C) 2011
   3  * Stefano Babic, DENX Software Engineering, sbabic@denx.de.
   4  *
   5  * Copyright (C) 2009 TechNexion Ltd.
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __TAM3517_H
  11 #define __TAM3517_H
  12
  13 /*
  14  * High Level Configuration Options
  15  */
  16
  17 #include <asm/arch/cpu.h>               /* get chip and board defs */
  18 #include <asm/arch/omap.h>
  19
  20 /* Clock Defines */
  21 #define V_OSCK                  26000000        /* Clock output from T2 */
  22 #define V_SCLK                  (V_OSCK >> 1)
  23
  24 #define CONFIG_MISC_INIT_R
  25
  26 #define CONFIG_CMDLINE_TAG                      /* enable passing of ATAGs */
  27 #define CONFIG_SETUP_MEMORY_TAGS
  28 #define CONFIG_INITRD_TAG
  29 #define CONFIG_REVISION_TAG
  30
  31 /*
  32  * Size of malloc() pool
  33  */
  34 #define CONFIG_ENV_SIZE                 (128 << 10)     /* 128 KiB sector */
  35 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + (128 << 10) + \
  36                                         2 * 1024 * 1024)
  37 /*
  38  * DDR related
  39  */
  40 #define CONFIG_SYS_CS0_SIZE             (256 * 1024 * 1024)
  41
  42 /*
  43  * Hardware drivers
  44  */
  45
  46 /*
  47  * NS16550 Configuration
  48  */
  49 #define CONFIG_SYS_NS16550_SERIAL
  50 #define CONFIG_SYS_NS16550_REG_SIZE     (-4)
  51 #define CONFIG_SYS_NS16550_CLK          48000000        /* 48MHz (APLL96/2) */
  52
  53 /*
  54  * select serial console configuration
  55  */
  56 #define CONFIG_CONS_INDEX               1
  57 #define CONFIG_SYS_NS16550_COM1         OMAP34XX_UART1
  58 #define CONFIG_SERIAL1                  /* UART1 */
  59
  60 /* allow to overwrite serial and ethaddr */
  61 #define CONFIG_ENV_OVERWRITE
  62 #define CONFIG_SYS_BAUDRATE_TABLE       {4800, 9600, 19200, 38400, 57600,\
  63                                         115200}
  64 /* EHCI */
  65 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO        25
  66
  67 #define CONFIG_SYS_I2C
  68 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50            /* base address */
  69 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1               /* bytes of address */
  70 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW     0x07
  71
  72 /*
  73  * Board NAND Info.
  74  */
  75 #define CONFIG_SYS_NAND_BASE            NAND_BASE       /* physical address */
  76                                                         /* to access */
  77                                                         /* nand at CS0 */
  78
  79 #define CONFIG_SYS_MAX_NAND_DEVICE      1               /* Max number of */
  80                                                         /* NAND devices */
  81
  82 #define CONFIG_AUTO_COMPLETE
  83
  84 /*
  85  * Miscellaneous configurable options
  86  */
  87 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
  88 #define CONFIG_CMDLINE_EDITING
  89 #define CONFIG_AUTO_COMPLETE
  90 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
  91
  92 #define CONFIG_SYS_MAXARGS              32      /* max number of command */
  93                                                 /* args */
  94 /* memtest works on */
  95 #define CONFIG_SYS_MEMTEST_START        (OMAP34XX_SDRC_CS0)
  96 #define CONFIG_SYS_MEMTEST_END          (OMAP34XX_SDRC_CS0 + \
  97                                         0x01F00000) /* 31MB */
  98
  99 #define CONFIG_SYS_LOAD_ADDR            (OMAP34XX_SDRC_CS0) /* default load */
 100                                                                 /* address */
 101
 102 /*
 103  * AM3517 has 12 GP timers, they can be driven by the system clock
 104  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
 105  * This rate is divided by a local divisor.
 106  */
 107 #define CONFIG_SYS_TIMERBASE            OMAP34XX_GPT2
 108 #define CONFIG_SYS_PTV                  2       /* Divisor: 2^(PTV+1) => 8 */
 109
 110 /*
 111  * Physical Memory Map
 112  */
 113 #define CONFIG_NR_DRAM_BANKS    2       /* CS1 may or may not be populated */
 114 #define PHYS_SDRAM_1            OMAP34XX_SDRC_CS0
 115 #define PHYS_SDRAM_2            OMAP34XX_SDRC_CS1
 116
 117 /*
 118  * FLASH and environment organization
 119  */
 120
 121 /* **** PISMO SUPPORT *** */
 122
 123 /* Redundant Environment */
 124 #define CONFIG_SYS_ENV_SECT_SIZE        (128 << 10)     /* 128 KiB */
 125 #define CONFIG_ENV_OFFSET               0x180000
 126 #define CONFIG_ENV_ADDR                 0x180000
 127 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + \
 128                                                 2 * CONFIG_SYS_ENV_SECT_SIZE)
 129 #define CONFIG_ENV_SIZE_REDUND          CONFIG_ENV_SIZE
 130
 131 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
 132 #define CONFIG_SYS_INIT_RAM_ADDR        0x4020f800
 133 #define CONFIG_SYS_INIT_RAM_SIZE        0x800
 134 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_INIT_RAM_ADDR + \
 135                                          CONFIG_SYS_INIT_RAM_SIZE - \
 136                                          GENERATED_GBL_DATA_SIZE)
 137
 138 /*
 139  * ethernet support, EMAC
 140  *
 141  */
 142 #define CONFIG_DRIVER_TI_EMAC
 143 #define CONFIG_DRIVER_TI_EMAC_USE_RMII
 144 #define CONFIG_MII
 145 #define CONFIG_BOOTP_DNS
 146 #define CONFIG_BOOTP_DNS2
 147 #define CONFIG_BOOTP_SEND_HOSTNAME
 148 #define CONFIG_NET_RETRY_COUNT 10
 149
 150 /* Defines for SPL */
 151 #define CONFIG_SPL_CONSOLE
 152 #define CONFIG_SPL_NAND_SOFTECC
 153 #define CONFIG_SPL_NAND_WORKSPACE       0x8f07f000 /* below BSS */
 154
 155 #define CONFIG_SPL_NAND_BASE
 156 #define CONFIG_SPL_NAND_DRIVERS
 157 #define CONFIG_SPL_NAND_ECC
 158
 159 #define CONFIG_SPL_TEXT_BASE            0x40200000 /*CONFIG_SYS_SRAM_START*/
 160 #define CONFIG_SPL_MAX_SIZE             (SRAM_SCRATCH_SPACE_ADDR - \
 161                                          CONFIG_SPL_TEXT_BASE)
 162 #define CONFIG_SPL_STACK                LOW_LEVEL_SRAM_STACK
 163
 164 #define CONFIG_SYS_SPL_MALLOC_START     0x8f000000
 165 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x80000
 166 #define CONFIG_SPL_BSS_START_ADDR       0x8f080000 /* end of RAM */
 167 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
 168
 169 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION      1
 170 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME         "u-boot.img"
 171
 172 /* FAT */
 173 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME          "uImage"
 174 #define CONFIG_SPL_FS_LOAD_ARGS_NAME            "args"
 175
 176 /* RAW SD card / eMMC */
 177 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900   /* address 0x120000 */
 178 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR   0x80    /* address 0x10000 */
 179 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS  0x80    /* 64KiB */
 180
 181 /* NAND boot config */
 182 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 183 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
 184 #define CONFIG_SYS_NAND_OOBSIZE         64
 185 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 186 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 187 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   0
 188 #define CONFIG_SYS_NAND_ECCPOS          {40, 41, 42, 43, 44, 45, 46, 47,\
 189                                          48, 49, 50, 51, 52, 53, 54, 55,\
 190                                          56, 57, 58, 59, 60, 61, 62, 63}
 191 #define CONFIG_SYS_NAND_ECCSIZE         256
 192 #define CONFIG_SYS_NAND_ECCBYTES        3
 193 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_HAM1_CODE_SW
 194
 195 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 196
 197 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
 198 #define CONFIG_SYS_NAND_U_BOOT_SIZE     0x80000
 199
 200 #define CONFIG_MTD_PARTITIONS
 201 #define CONFIG_MTD_DEVICE
 202
 203 /* Setup MTD for NAND on the SOM */
 204
 205 #define CONFIG_TAM3517_SETTINGS                                         \
 206         "netdev=eth0\0"                                                 \
 207         "nandargs=setenv bootargs root=${nandroot} "                    \
 208                 "rootfstype=${nandrootfstype}\0"                        \
 209         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 210                 "nfsroot=${serverip}:${rootpath}\0"                     \
 211         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 212         "addip_sta=setenv bootargs ${bootargs} "                        \
 213                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 214                 ":${hostname}:${netdev}:off panic=1\0"                  \
 215         "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"               \
 216         "addip=if test -n ${ipdyn};then run addip_dyn;"                 \
 217                 "else run addip_sta;fi\0"                               \
 218         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 219         "addtty=setenv bootargs ${bootargs}"                            \
 220                 " console=ttyO0,${baudrate}\0"                          \
 221         "addmisc=setenv bootargs ${bootargs} ${misc}\0"                 \
 222         "loadaddr=82000000\0"                                           \
 223         "kernel_addr_r=82000000\0"                                      \
 224         "hostname=" __stringify(CONFIG_HOSTNAME) "\0"                   \
 225         "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0"            \
 226         "flash_self=run ramargs addip addtty addmtd addmisc;"           \
 227                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 228         "flash_nfs=run nfsargs addip addtty addmtd addmisc;"            \
 229                 "bootm ${kernel_addr}\0"                                \
 230         "nandboot=run nandargs addip addtty addmtd addmisc;"            \
 231                 "nand read ${kernel_addr_r} kernel\0"                   \
 232                 "bootm ${kernel_addr_r}\0"                              \
 233         "net_nfs=tftp ${kernel_addr_r} ${bootfile}; "                   \
 234                 "run nfsargs addip addtty addmtd addmisc;"              \
 235                 "bootm ${kernel_addr_r}\0"                              \
 236         "net_self=if run net_self_load;then "                           \
 237                 "run ramargs addip addtty addmtd addmisc;"              \
 238                 "bootm ${kernel_addr_r} ${ramdisk_addr_r};"             \
 239                 "else echo Images not loades;fi\0"                      \
 240         "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.img\0"          \
 241         "load=tftp ${loadaddr} ${u-boot}\0"                             \
 242         "loadmlo=tftp ${loadaddr} ${mlo}\0"                             \
 243         "mlo=" __stringify(CONFIG_HOSTNAME) "/MLO\0"                    \
 244         "uboot_addr=0x80000\0"                                          \
 245         "update=nandecc sw;nand erase ${uboot_addr} 100000;"            \
 246                 "nand write ${loadaddr} ${uboot_addr} 80000\0"          \
 247         "updatemlo=nandecc hw;nand erase 0 20000;"                      \
 248                 "nand write ${loadaddr} 0 20000\0"                      \
 249         "upd=if run load;then echo Updating u-boot;if run update;"      \
 250                 "then echo U-Boot updated;"                             \
 251                         "else echo Error updating u-boot !;"            \
 252                         "echo Board without bootloader !!;"             \
 253                 "fi;"                                                   \
 254                 "else echo U-Boot not downloaded..exiting;fi\0"         \
 255
 256 /*
 257  * this is common code for all TAM3517 boards.
 258  * MAC address is stored from manufacturer in
 259  * I2C EEPROM
 260  */
 261 #if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__))
 262 /*
 263  * The I2C EEPROM on the TAM3517 contains
 264  * mac address and production data
 265  */
 266 struct tam3517_module_info {
 267         char customer[48];
 268         char product[48];
 269
 270         /*
 271          * bit 0~47  : sequence number
 272          * bit 48~55 : week of year, from 0.
 273          * bit 56~63 : year
 274          */
 275         unsigned long long sequence_number;
 276
 277         /*
 278          * bit 0~7   : revision fixed
 279          * bit 8~15  : revision major
 280          * bit 16~31 : TNxxx
 281          */
 282         unsigned int revision;
 283         unsigned char eth_addr[4][8];
 284         unsigned char _rev[100];
 285 };
 286
 287 #define TAM3517_READ_EEPROM(info, ret) \
 288 do {                                                            \
 289         i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); \
 290         if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,          \
 291                 (void *)info, sizeof(*info)))                   \
 292                 ret = 1;                                        \
 293         else                                                    \
 294                 ret = 0;                                        \
 295 } while (0)
 296
 297 #define TAM3517_READ_MAC_FROM_EEPROM(info)                      \
 298 do {                                                            \
 299         char buf[80], ethname[20];                              \
 300         int i;                                                  \
 301         memset(buf, 0, sizeof(buf));                            \
 302         for (i = 0 ; i < ARRAY_SIZE((info)->eth_addr); i++) {   \
 303                 sprintf(buf, "%02X:%02X:%02X:%02X:%02X:%02X",   \
 304                         (info)->eth_addr[i][5],                 \
 305                         (info)->eth_addr[i][4],                 \
 306                         (info)->eth_addr[i][3],                 \
 307                         (info)->eth_addr[i][2],                 \
 308                         (info)->eth_addr[i][1],                 \
 309                         (info)->eth_addr[i][0]);                        \
 310                                                                 \
 311                 if (i)                                          \
 312                         sprintf(ethname, "eth%daddr", i);       \
 313                 else                                            \
 314                         strcpy(ethname, "ethaddr");             \
 315                 printf("Setting %s from EEPROM with %s\n", ethname, buf);\
 316                 env_set(ethname, buf);                          \
 317         }                                                       \
 318 } while (0)
 319
 320 /* The following macros are taken from Technexion's documentation */
 321 #define TAM3517_sequence_number(info) \
 322         ((info)->sequence_number % 0x1000000000000LL)
 323 #define TAM3517_week_of_year(info) (((info)->sequence_number >> 48) % 0x100)
 324 #define TAM3517_year(info) ((info)->sequence_number >> 56)
 325 #define TAM3517_revision_fixed(info) ((info)->revision % 0x100)
 326 #define TAM3517_revision_major(info) (((info)->revision >> 8) % 0x100)
 327 #define TAM3517_revision_tn(info) ((info)->revision >> 16)
 328
 329 #define TAM3517_PRINT_SOM_INFO(info)                            \
 330 do {                                                            \
 331         printf("Vendor:%s\n", (info)->customer);                \
 332         printf("SOM:   %s\n", (info)->product);                 \
 333         printf("SeqNr: %02llu%02llu%012llu\n",                  \
 334                 TAM3517_year(info),                             \
 335                 TAM3517_week_of_year(info),                     \
 336                 TAM3517_sequence_number(info));                 \
 337         printf("Rev:   TN%u %u.%u\n",                           \
 338                 TAM3517_revision_tn(info),                      \
 339                 TAM3517_revision_major(info),                   \
 340                 TAM3517_revision_fixed(info));                  \
 341 } while (0)
 342
 343 #endif
 344
 345 #endif /* __TAM3517_H */