include/configs/ti_armv7_common.h

   1 /*
   2  * ti_armv7_common.h
   3  *
   4  * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  *
   8  * The various ARMv7 SoCs from TI all share a number of IP blocks when
   9  * implementing a given feature.  Rather than define these in every
  10  * board or even SoC common file, we define a common file to be re-used
  11  * in all cases.  While technically true that some of these details are
  12  * configurable at the board design, they are common throughout SoC
  13  * reference platforms as well as custom designs and become de facto
  14  * standards.
  15  */
  16
  17 #ifndef __CONFIG_TI_ARMV7_COMMON_H__
  18 #define __CONFIG_TI_ARMV7_COMMON_H__
  19
  20 /*
  21  * We typically do not contain NOR flash.  In the cases where we do, we
  22  * undefine this later.
  23  */
  24 #define CONFIG_SYS_NO_FLASH
  25
  26 /* Support both device trees and ATAGs. */
  27 #define CONFIG_OF_LIBFDT
  28 #define CONFIG_CMDLINE_TAG
  29 #define CONFIG_SETUP_MEMORY_TAGS
  30 #define CONFIG_INITRD_TAG
  31
  32 /*
  33  * Our DDR memory always starts at 0x80000000 and U-Boot shall have
  34  * relocated itself to higher in memory by the time this value is used.
  35  * However, set this to a 32MB offset to allow for easier Linux kernel
  36  * booting as the default is often used as the kernel load address.
  37  */
  38 #define CONFIG_SYS_LOAD_ADDR            0x82000000
  39
  40 /*
  41  * We setup defaults based on constraints from the Linux kernel, which should
  42  * also be safe elsewhere.  We have the default load at 32MB into DDR (for
  43  * the kernel), FDT above 128MB (the maximum location for the end of the
  44  * kernel), and the ramdisk 512KB above that (allowing for hopefully never
  45  * seen large trees).  We say all of this must be within the first 256MB
  46  * as that will normally be within the kernel lowmem and thus visible via
  47  * bootm_size and we only run on platforms with 256MB or more of memory.
  48  */
  49 #define DEFAULT_LINUX_BOOT_ENV \
  50         "loadaddr=0x82000000\0" \
  51         "kernel_addr_r=0x82000000\0" \
  52         "fdtaddr=0x88000000\0" \
  53         "fdt_addr_r=0x88000000\0" \
  54         "rdaddr=0x88080000\0" \
  55         "ramdisk_addr_r=0x88080000\0" \
  56         "scriptaddr=0x80000000\0" \
  57         "pxefile_addr_r=0x80100000\0" \
  58         "bootm_size=0x10000000\0"
  59
  60 #define DEFAULT_MMC_TI_ARGS \
  61         "mmcdev=0\0" \
  62         "mmcrootfstype=ext4 rootwait\0" \
  63         "finduuid=part uuid mmc 0:2 uuid\0" \
  64         "args_mmc=run finduuid;setenv bootargs console=${console} " \
  65                 "${optargs} " \
  66                 "root=PARTUUID=${uuid} rw " \
  67                 "rootfstype=${mmcrootfstype}\0"
  68
  69 /*
  70  * Default to a quick boot delay.
  71  */
  72 #define CONFIG_BOOTDELAY                1
  73
  74 /*
  75  * DDR information.  If the CONFIG_NR_DRAM_BANKS is not defined,
  76  * we say (for simplicity) that we have 1 bank, always, even when
  77  * we have more.  We always start at 0x80000000, and we place the
  78  * initial stack pointer in our SRAM. Otherwise, we can define
  79  * CONFIG_NR_DRAM_BANKS before including this file.
  80  */
  81 #ifndef CONFIG_NR_DRAM_BANKS
  82 #define CONFIG_NR_DRAM_BANKS            1
  83 #endif
  84 #define CONFIG_SYS_SDRAM_BASE           0x80000000
  85
  86 #ifndef CONFIG_SYS_INIT_SP_ADDR
  87 #define CONFIG_SYS_INIT_SP_ADDR         (NON_SECURE_SRAM_END - \
  88                                                 GENERATED_GBL_DATA_SIZE)
  89 #endif
  90
  91 /* Timer information. */
  92 #define CONFIG_SYS_PTV                  2       /* Divisor: 2^(PTV+1) => 8 */
  93
  94 /* I2C IP block */
  95 #define CONFIG_I2C
  96 #define CONFIG_CMD_I2C
  97 #define CONFIG_SYS_I2C
  98
  99 /* MMC/SD IP block */
 100 #define CONFIG_MMC
 101 #define CONFIG_GENERIC_MMC
 102 #define CONFIG_CMD_MMC
 103
 104 /* McSPI IP block */
 105 #define CONFIG_SPI
 106 #define CONFIG_CMD_SPI
 107
 108 /* GPIO block */
 109 #define CONFIG_CMD_GPIO
 110
 111 /*
 112  * The following are general good-enough settings for U-Boot.  We set a
 113  * large malloc pool as we generally have a lot of DDR, and we opt for
 114  * function over binary size in the main portion of U-Boot as this is
 115  * generally easily constrained later if needed.  We enable the config
 116  * options that give us information in the environment about what board
 117  * we are on so we do not need to rely on the command prompt.  We set a
 118  * console baudrate of 115200 and use the default baud rate table.
 119  */
 120 #ifdef CONFIG_DFU_MMC
 121 #define CONFIG_SYS_MALLOC_LEN   ((16 << 20) + CONFIG_SYS_DFU_DATA_BUF_SIZE)
 122 #else
 123 #define CONFIG_SYS_MALLOC_LEN   (16 << 20)
 124 #endif
 125 #define CONFIG_SYS_HUSH_PARSER
 126 #define CONFIG_SYS_CONSOLE_INFO_QUIET
 127 #define CONFIG_BAUDRATE                 115200
 128 #define CONFIG_ENV_VARS_UBOOT_CONFIG    /* Strongly encouraged */
 129 #define CONFIG_ENV_OVERWRITE            /* Overwrite ethaddr / serial# */
 130
 131 /* As stated above, the following choices are optional. */
 132 #define CONFIG_SYS_LONGHELP
 133 #define CONFIG_AUTO_COMPLETE
 134 #define CONFIG_CMDLINE_EDITING
 135 #define CONFIG_VERSION_VARIABLE
 136
 137 /* We set the max number of command args high to avoid HUSH bugs. */
 138 #define CONFIG_SYS_MAXARGS              64
 139
 140 /* Console I/O Buffer Size */
 141 #define CONFIG_SYS_CBSIZE               512
 142 /* Print Buffer Size */
 143 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE \
 144                                         + sizeof(CONFIG_SYS_PROMPT) + 16)
 145 /* Boot Argument Buffer Size */
 146 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 147
 148 /*
 149  * When we have SPI, NOR or NAND flash we expect to be making use of
 150  * mtdparts, both for ease of use in U-Boot and for passing information
 151  * on to the Linux kernel.
 152  */
 153 #if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NOR) || defined(CONFIG_NAND) || defined(CONFIG_NAND_DAVINCI)
 154 #define CONFIG_MTD_DEVICE               /* Required for mtdparts */
 155 #define CONFIG_CMD_MTDPARTS
 156 #endif
 157
 158 #define CONFIG_CMD_ASKENV
 159 #define CONFIG_CMD_BOOTZ
 160 #define CONFIG_SUPPORT_RAW_INITRD
 161
 162 /*
 163  * Common filesystems support.  When we have removable storage we
 164  * enabled a number of useful commands and support.
 165  */
 166 #if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE)
 167 #define CONFIG_DOS_PARTITION
 168 #define CONFIG_CMD_FAT
 169 #define CONFIG_FAT_WRITE
 170 #define CONFIG_CMD_EXT2
 171 #define CONFIG_CMD_EXT4
 172 #define CONFIG_CMD_FS_GENERIC
 173 #define CONFIG_PARTITION_UUIDS
 174 #define CONFIG_CMD_PART
 175 #endif
 176
 177 /*
 178  * Our platforms make use of SPL to initalize the hardware (primarily
 179  * memory) enough for full U-Boot to be loaded.  We also support Falcon
 180  * Mode so that the Linux kernel can be booted directly from SPL
 181  * instead, if desired.  We make use of the general SPL framework found
 182  * under common/spl/.  Given our generally common memory map, we set a
 183  * number of related defaults and sizes here.
 184  */
 185 #if !defined(CONFIG_NOR_BOOT) && \
 186         !(defined(CONFIG_QSPI_BOOT) && defined(CONFIG_AM43XX))
 187 #define CONFIG_SPL_FRAMEWORK
 188 #define CONFIG_SPL_OS_BOOT
 189
 190 /*
 191  * Place the image at the start of the ROM defined image space (per
 192  * CONFIG_SPL_TEXT_BASE and we limit our size to the ROM-defined
 193  * downloaded image area.  We initalize DRAM as soon as we can so that
 194  * we can place stack, malloc and BSS there.  We load U-Boot itself into
 195  * memory at 0x80800000 for legacy reasons (to not conflict with older
 196  * SPLs).  We have our BSS be placed 2MiB after this, to allow for the
 197  * default Linux kernel address of 0x80008000 to work with most sized
 198  * kernels, in the Falcon Mode case.  We have the SPL malloc pool at the
 199  * end of the BSS area.  We suggest that the stack be placed at 32MiB after
 200  * the start of DRAM to allow room for all of the above (handled in Kconfig).
 201  */
 202 #ifndef CONFIG_SYS_TEXT_BASE
 203 #define CONFIG_SYS_TEXT_BASE            0x80800000
 204 #endif
 205 #ifndef CONFIG_SPL_BSS_START_ADDR
 206 #define CONFIG_SPL_BSS_START_ADDR       0x80a00000
 207 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000         /* 512 KB */
 208 #endif
 209 #ifndef CONFIG_SYS_SPL_MALLOC_START
 210 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
 211                                          CONFIG_SPL_BSS_MAX_SIZE)
 212 #define CONFIG_SYS_SPL_MALLOC_SIZE      CONFIG_SYS_MALLOC_LEN
 213 #endif
 214
 215 /* RAW SD card / eMMC locations. */
 216 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
 217 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS      0x200 /* 256 KB */
 218
 219 /* FAT sd card locations. */
 220 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION      1
 221 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
 222
 223 #ifdef CONFIG_SPL_OS_BOOT
 224 /* FAT */
 225 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME          "uImage"
 226 #define CONFIG_SPL_FS_LOAD_ARGS_NAME            "args"
 227
 228 /* RAW SD card / eMMC */
 229 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900   /* address 0x120000 */
 230 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR   0x80    /* address 0x10000 */
 231 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS  0x80    /* 64KiB */
 232
 233 /* spl export command */
 234 #define CONFIG_CMD_SPL
 235 #endif
 236
 237 #ifdef CONFIG_MMC
 238 #define CONFIG_SPL_LIBDISK_SUPPORT
 239 #define CONFIG_SPL_MMC_SUPPORT
 240 #define CONFIG_SPL_FAT_SUPPORT
 241 #define CONFIG_SPL_EXT_SUPPORT
 242 #endif
 243
 244 #define CONFIG_SYS_THUMB_BUILD
 245
 246 /* General parts of the framework, required. */
 247 #define CONFIG_SPL_I2C_SUPPORT
 248 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 249 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 250 #define CONFIG_SPL_SERIAL_SUPPORT
 251 #define CONFIG_SPL_POWER_SUPPORT
 252 #define CONFIG_SPL_GPIO_SUPPORT
 253 #define CONFIG_SPL_BOARD_INIT
 254
 255 #ifdef CONFIG_NAND
 256 #define CONFIG_SPL_NAND_SUPPORT
 257 #define CONFIG_SPL_NAND_BASE
 258 #define CONFIG_SPL_NAND_DRIVERS
 259 #define CONFIG_SPL_NAND_ECC
 260 #define CONFIG_SPL_MTD_SUPPORT
 261 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 262 #endif
 263 #endif /* !CONFIG_NOR_BOOT */
 264
 265 /* Generic Environment Variables */
 266
 267 #ifdef CONFIG_CMD_NET
 268 #define NETARGS \
 269         "static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
 270                 "::off\0" \
 271         "nfsopts=nolock\0" \
 272         "rootpath=/export/rootfs\0" \
 273         "netloadimage=tftp ${loadaddr} ${bootfile}\0" \
 274         "netloadfdt=tftp ${fdtaddr} ${fdtfile}\0" \
 275         "netargs=setenv bootargs console=${console} " \
 276                 "${optargs} " \
 277                 "root=/dev/nfs " \
 278                 "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
 279                 "ip=dhcp\0" \
 280         "netboot=echo Booting from network ...; " \
 281                 "setenv autoload no; " \
 282                 "dhcp; " \
 283                 "run netloadimage; " \
 284                 "run netloadfdt; " \
 285                 "run netargs; " \
 286                 "bootz ${loadaddr} - ${fdtaddr}\0"
 287 #else
 288 #define NETARGS ""
 289 #endif
 290
 291 #endif  /* __CONFIG_TI_ARMV7_COMMON_H__ */