include/configs/ti_armv7_keystone2.h

   1 /*
   2  * Common configuration header file for all Keystone II EVM platforms
   3  *
   4  * (C) Copyright 2012-2014
   5  *     Texas Instruments Incorporated, <www.ti.com>
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __CONFIG_KS2_EVM_H
  11 #define __CONFIG_KS2_EVM_H
  12
  13 #define CONFIG_SOC_KEYSTONE
  14
  15 /* U-Boot Build Configuration */
  16 #define CONFIG_SKIP_LOWLEVEL_INIT       /* U-Boot is a 2nd stage loader */
  17 #define CONFIG_BOARD_EARLY_INIT_F
  18 #define CONFIG_DISPLAY_CPUINFO
  19
  20 /* SoC Configuration */
  21 #define CONFIG_ARCH_CPU_INIT
  22 #define CONFIG_SYS_ARCH_TIMER
  23 #define CONFIG_SYS_TEXT_BASE            0x0c000000
  24 #define CONFIG_SPL_TARGET               "u-boot-spi.gph"
  25 #define CONFIG_SYS_DCACHE_OFF
  26
  27 /* Memory Configuration */
  28 #define CONFIG_NR_DRAM_BANKS            2
  29 #define CONFIG_SYS_LPAE_SDRAM_BASE      0x800000000
  30 #define CONFIG_MAX_RAM_BANK_SIZE        (2 << 30)       /* 2GB */
  31 #define CONFIG_STACKSIZE                (512 << 10)     /* 512 KiB */
  32 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SPL_TEXT_BASE - \
  33                                         GENERATED_GBL_DATA_SIZE)
  34
  35 #ifdef CONFIG_SYS_MALLOC_F_LEN
  36 #define SPL_MALLOC_F_SIZE       CONFIG_SYS_MALLOC_F_LEN
  37 #else
  38 #define SPL_MALLOC_F_SIZE       0
  39 #endif
  40
  41 /* SPL SPI Loader Configuration */
  42 #define CONFIG_SPL_PAD_TO               65536
  43 #define CONFIG_SPL_MAX_SIZE             (CONFIG_SPL_PAD_TO - 8)
  44 #define CONFIG_SPL_BSS_START_ADDR       (CONFIG_SPL_TEXT_BASE + \
  45                                         CONFIG_SPL_MAX_SIZE)
  46 #define CONFIG_SPL_BSS_MAX_SIZE         (32 * 1024)
  47 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
  48                                         CONFIG_SPL_BSS_MAX_SIZE)
  49 #define CONFIG_SYS_SPL_MALLOC_SIZE      (32 * 1024)
  50 #define CONFIG_SPL_STACK_SIZE           (8 * 1024)
  51 #define CONFIG_SPL_STACK                (CONFIG_SYS_SPL_MALLOC_START + \
  52                                         CONFIG_SYS_SPL_MALLOC_SIZE + \
  53                                         SPL_MALLOC_F_SIZE + \
  54                                         CONFIG_SPL_STACK_SIZE - 4)
  55 #define CONFIG_SPL_SPI_FLASH_SUPPORT
  56 #define CONFIG_SPL_SPI_SUPPORT
  57 #define CONFIG_SPL_SPI_LOAD
  58 #define CONFIG_SYS_SPI_U_BOOT_OFFS      CONFIG_SPL_PAD_TO
  59
  60 /* UART Configuration */
  61 #define CONFIG_SYS_NS16550_MEM32
  62 #if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_DM_SERIAL)
  63 #define CONFIG_SYS_NS16550_SERIAL
  64 #define CONFIG_SYS_NS16550_REG_SIZE     -4
  65 #endif
  66 #define CONFIG_SYS_NS16550_COM1         KS2_UART0_BASE
  67 #define CONFIG_SYS_NS16550_COM2         KS2_UART1_BASE
  68 #define CONFIG_CONS_INDEX               1
  69
  70 #ifndef CONFIG_SOC_K2G
  71 #define CONFIG_SYS_NS16550_CLK          clk_get_rate(KS2_CLK1_6)
  72 #else
  73 #define CONFIG_SYS_NS16550_CLK          clk_get_rate(uart_pll_clk) / 2
  74 #endif
  75
  76 /* SPI Configuration */
  77 #define CONFIG_SPI_FLASH_STMICRO
  78 #define CONFIG_DAVINCI_SPI
  79 #define CONFIG_SYS_SPI_CLK              clk_get_rate(KS2_CLK1_6)
  80 #define CONFIG_SF_DEFAULT_SPEED         30000000
  81 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
  82 #define CONFIG_SYS_SPI0
  83 #define CONFIG_SYS_SPI_BASE             KS2_SPI0_BASE
  84 #define CONFIG_SYS_SPI0_NUM_CS          4
  85 #define CONFIG_SYS_SPI1
  86 #define CONFIG_SYS_SPI1_BASE            KS2_SPI1_BASE
  87 #define CONFIG_SYS_SPI1_NUM_CS          4
  88 #define CONFIG_SYS_SPI2
  89 #define CONFIG_SYS_SPI2_BASE            KS2_SPI2_BASE
  90 #define CONFIG_SYS_SPI2_NUM_CS          4
  91
  92 /* Network Configuration */
  93 #define CONFIG_PHYLIB
  94 #define CONFIG_PHY_MARVELL
  95 #define CONFIG_MII
  96 #define CONFIG_BOOTP_DEFAULT
  97 #define CONFIG_BOOTP_DNS
  98 #define CONFIG_BOOTP_DNS2
  99 #define CONFIG_BOOTP_SEND_HOSTNAME
 100 #define CONFIG_NET_RETRY_COUNT          32
 101 #define CONFIG_SYS_SGMII_REFCLK_MHZ     312
 102 #define CONFIG_SYS_SGMII_LINERATE_MHZ   1250
 103 #define CONFIG_SYS_SGMII_RATESCALE      2
 104
 105 /* Keyston Navigator Configuration */
 106 #define CONFIG_TI_KSNAV
 107 #define CONFIG_KSNAV_QM_BASE_ADDRESS            KS2_QM_BASE_ADDRESS
 108 #define CONFIG_KSNAV_QM_CONF_BASE               KS2_QM_CONF_BASE
 109 #define CONFIG_KSNAV_QM_DESC_SETUP_BASE         KS2_QM_DESC_SETUP_BASE
 110 #define CONFIG_KSNAV_QM_STATUS_RAM_BASE         KS2_QM_STATUS_RAM_BASE
 111 #define CONFIG_KSNAV_QM_INTD_CONF_BASE          KS2_QM_INTD_CONF_BASE
 112 #define CONFIG_KSNAV_QM_PDSP1_CMD_BASE          KS2_QM_PDSP1_CMD_BASE
 113 #define CONFIG_KSNAV_QM_PDSP1_CTRL_BASE         KS2_QM_PDSP1_CTRL_BASE
 114 #define CONFIG_KSNAV_QM_PDSP1_IRAM_BASE         KS2_QM_PDSP1_IRAM_BASE
 115 #define CONFIG_KSNAV_QM_MANAGER_QUEUES_BASE     KS2_QM_MANAGER_QUEUES_BASE
 116 #define CONFIG_KSNAV_QM_MANAGER_Q_PROXY_BASE    KS2_QM_MANAGER_Q_PROXY_BASE
 117 #define CONFIG_KSNAV_QM_QUEUE_STATUS_BASE       KS2_QM_QUEUE_STATUS_BASE
 118 #define CONFIG_KSNAV_QM_LINK_RAM_BASE           KS2_QM_LINK_RAM_BASE
 119 #define CONFIG_KSNAV_QM_REGION_NUM              KS2_QM_REGION_NUM
 120 #define CONFIG_KSNAV_QM_QPOOL_NUM               KS2_QM_QPOOL_NUM
 121
 122 /* NETCP pktdma */
 123 #define CONFIG_KSNAV_PKTDMA_NETCP
 124 #define CONFIG_KSNAV_NETCP_PDMA_CTRL_BASE       KS2_NETCP_PDMA_CTRL_BASE
 125 #define CONFIG_KSNAV_NETCP_PDMA_TX_BASE         KS2_NETCP_PDMA_TX_BASE
 126 #define CONFIG_KSNAV_NETCP_PDMA_TX_CH_NUM       KS2_NETCP_PDMA_TX_CH_NUM
 127 #define CONFIG_KSNAV_NETCP_PDMA_RX_BASE         KS2_NETCP_PDMA_RX_BASE
 128 #define CONFIG_KSNAV_NETCP_PDMA_RX_CH_NUM       KS2_NETCP_PDMA_RX_CH_NUM
 129 #define CONFIG_KSNAV_NETCP_PDMA_SCHED_BASE      KS2_NETCP_PDMA_SCHED_BASE
 130 #define CONFIG_KSNAV_NETCP_PDMA_RX_FLOW_BASE    KS2_NETCP_PDMA_RX_FLOW_BASE
 131 #define CONFIG_KSNAV_NETCP_PDMA_RX_FLOW_NUM     KS2_NETCP_PDMA_RX_FLOW_NUM
 132 #define CONFIG_KSNAV_NETCP_PDMA_RX_FREE_QUEUE   KS2_NETCP_PDMA_RX_FREE_QUEUE
 133 #define CONFIG_KSNAV_NETCP_PDMA_RX_RCV_QUEUE    KS2_NETCP_PDMA_RX_RCV_QUEUE
 134 #define CONFIG_KSNAV_NETCP_PDMA_TX_SND_QUEUE    KS2_NETCP_PDMA_TX_SND_QUEUE
 135
 136 /* Keystone net */
 137 #define CONFIG_DRIVER_TI_KEYSTONE_NET
 138 #define CONFIG_KSNET_MAC_ID_BASE                KS2_MAC_ID_BASE_ADDR
 139 #define CONFIG_KSNET_NETCP_BASE                 KS2_NETCP_BASE
 140 #define CONFIG_KSNET_SERDES_SGMII_BASE          KS2_SGMII_SERDES_BASE
 141 #define CONFIG_KSNET_SERDES_SGMII2_BASE         KS2_SGMII_SERDES2_BASE
 142 #define CONFIG_KSNET_SERDES_LANES_PER_SGMII     KS2_LANES_PER_SGMII_SERDES
 143
 144 /* SerDes */
 145 #define CONFIG_TI_KEYSTONE_SERDES
 146
 147 /* AEMIF */
 148 #define CONFIG_TI_AEMIF
 149 #define CONFIG_AEMIF_CNTRL_BASE         KS2_AEMIF_CNTRL_BASE
 150
 151 /* I2C Configuration */
 152 #define CONFIG_SYS_I2C_DAVINCI
 153 #define CONFIG_SYS_DAVINCI_I2C_SPEED    100000
 154 #define CONFIG_SYS_DAVINCI_I2C_SLAVE    0x10 /* SMBus host address */
 155 #define CONFIG_SYS_DAVINCI_I2C_SPEED1   100000
 156 #define CONFIG_SYS_DAVINCI_I2C_SLAVE1   0x10 /* SMBus host address */
 157 #define CONFIG_SYS_DAVINCI_I2C_SPEED2   100000
 158 #define CONFIG_SYS_DAVINCI_I2C_SLAVE2   0x10 /* SMBus host address */
 159 #define I2C_BUS_MAX                     3
 160
 161 /* EEPROM definitions */
 162 #define CONFIG_SYS_I2C_MULTI_EEPROMS
 163 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
 164 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x50
 165 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6
 166 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   20
 167 #define CONFIG_ENV_EEPROM_IS_ON_I2C
 168
 169 /* NAND Configuration */
 170 #define CONFIG_NAND_DAVINCI
 171 #define CONFIG_KEYSTONE_RBL_NAND
 172 #define CONFIG_KEYSTONE_NAND_MAX_RBL_SIZE       CONFIG_ENV_OFFSET
 173 #define CONFIG_SYS_NAND_MASK_CLE                0x4000
 174 #define CONFIG_SYS_NAND_MASK_ALE                0x2000
 175 #define CONFIG_SYS_NAND_CS                      2
 176 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 177 #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
 178
 179 #define CONFIG_SYS_NAND_LARGEPAGE
 180 #define CONFIG_SYS_NAND_BASE_LIST               { 0x30000000, }
 181 #define CONFIG_SYS_MAX_NAND_DEVICE              1
 182 #define CONFIG_SYS_NAND_MAX_CHIPS               1
 183 #define CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
 184 #define CONFIG_ENV_SIZE                         (256 << 10)  /* 256 KiB */
 185 #define CONFIG_ENV_IS_IN_NAND
 186 #define CONFIG_ENV_OFFSET                       0x100000
 187 #define CONFIG_MTD_PARTITIONS
 188 #define CONFIG_RBTREE
 189 #define CONFIG_LZO
 190 #define MTDIDS_DEFAULT                  "nand0=davinci_nand.0"
 191 #define MTDPARTS_DEFAULT                "mtdparts=davinci_nand.0:" \
 192                                         "1024k(bootloader)ro,512k(params)ro," \
 193                                         "-(ubifs)"
 194
 195 /* USB Configuration */
 196 #define CONFIG_USB_XHCI
 197 #define CONFIG_USB_XHCI_DWC3
 198 #define CONFIG_USB_XHCI_KEYSTONE
 199 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2
 200 #define CONFIG_EFI_PARTITION
 201 #define CONFIG_FS_FAT
 202 #define CONFIG_SYS_CACHELINE_SIZE               64
 203 #define CONFIG_USB_SS_BASE                      KS2_USB_SS_BASE
 204 #define CONFIG_USB_HOST_XHCI_BASE               KS2_USB_HOST_XHCI_BASE
 205 #define CONFIG_DEV_USB_PHY_BASE                 KS2_DEV_USB_PHY_BASE
 206 #define CONFIG_USB_PHY_CFG_BASE                 KS2_USB_PHY_CFG_BASE
 207
 208 /* U-Boot command configuration */
 209 #define CONFIG_CMD_DHCP
 210 #define CONFIG_CMD_PING
 211 #define CONFIG_CMD_SAVES
 212 #define CONFIG_CMD_NAND
 213 #define CONFIG_CMD_UBI
 214 #define CONFIG_CMD_UBIFS
 215 #define CONFIG_CMD_SF
 216 #define CONFIG_CMD_EEPROM
 217 #define CONFIG_CMD_USB
 218
 219 /* U-Boot general configuration */
 220 #define CONFIG_MISC_INIT_R
 221 #define CONFIG_CRC32_VERIFY
 222 #define CONFIG_MX_CYCLIC
 223 #define CONFIG_TIMESTAMP
 224
 225 /* EDMA3 */
 226 #define CONFIG_TI_EDMA3
 227
 228 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 229         DEFAULT_LINUX_BOOT_ENV                                          \
 230         CONFIG_EXTRA_ENV_KS2_BOARD_SETTINGS                             \
 231         "boot=ubi\0"                                                    \
 232         "tftp_root=/\0"                                                 \
 233         "nfs_root=/export\0"                                            \
 234         "mem_lpae=1\0"                                                  \
 235         "mem_reserve=512M\0"                                            \
 236         "addr_ubi=0x82000000\0"                                         \
 237         "addr_secdb_key=0xc000000\0"                                    \
 238         "name_kern=zImage\0"                                            \
 239         "run_mon=mon_install ${addr_mon}\0"                             \
 240         "run_kern=bootz ${loadaddr} - ${fdtaddr}\0"                     \
 241         "init_net=run args_all args_net\0"                              \
 242         "init_ubi=run args_all args_ubi; "                              \
 243                 "ubi part ubifs; ubifsmount ubi:boot;"                  \
 244                 "ubifsload ${addr_secdb_key} securedb.key.bin;\0"       \
 245         "get_fdt_net=dhcp ${fdtaddr} ${tftp_root}/${name_fdt}\0"        \
 246         "get_fdt_ubi=ubifsload ${fdtaddr} ${name_fdt}\0"                \
 247         "get_kern_net=dhcp ${loadaddr} ${tftp_root}/${name_kern}\0"     \
 248         "get_kern_ubi=ubifsload ${loadaddr} ${name_kern}\0"             \
 249         "get_mon_net=dhcp ${addr_mon} ${tftp_root}/${name_mon}\0"       \
 250         "get_mon_ubi=ubifsload ${addr_mon} ${name_mon}\0"               \
 251         "get_uboot_net=dhcp ${loadaddr} ${tftp_root}/${name_uboot}\0"   \
 252         "burn_uboot_spi=sf probe; sf erase 0 0x100000; "                \
 253                 "sf write ${loadaddr} 0 ${filesize}\0"          \
 254         "burn_uboot_nand=nand erase 0 0x100000; "                       \
 255                 "nand write ${loadaddr} 0 ${filesize}\0"                \
 256         "args_all=setenv bootargs console=ttyS0,115200n8 rootwait=1\0"  \
 257         "args_net=setenv bootargs ${bootargs} rootfstype=nfs "          \
 258                 "root=/dev/nfs rw nfsroot=${serverip}:${nfs_root},"     \
 259                 "${nfs_options} ip=dhcp\0"                              \
 260         "nfs_options=v3,tcp,rsize=4096,wsize=4096\0"                    \
 261         "get_fdt_ramfs=dhcp ${fdtaddr} ${tftp_root}/${name_fdt}\0"      \
 262         "get_kern_ramfs=dhcp ${loadaddr} ${tftp_root}/${name_kern}\0"   \
 263         "get_mon_ramfs=dhcp ${addr_mon} ${tftp_root}/${name_mon}\0"     \
 264         "get_fs_ramfs=dhcp ${rdaddr} ${tftp_root}/${name_fs}\0" \
 265         "get_ubi_net=dhcp ${addr_ubi} ${tftp_root}/${name_ubi}\0"       \
 266         "burn_ubi=nand erase.part ubifs; "                              \
 267                 "nand write ${addr_ubi} ubifs ${filesize}\0"            \
 268         "init_ramfs=run args_all args_ramfs get_fs_ramfs\0"             \
 269         "args_ramfs=setenv bootargs ${bootargs} "                       \
 270                 "rdinit=/sbin/init rw root=/dev/ram0 "                  \
 271                 "initrd=0x808080000,80M\0"                              \
 272         "no_post=1\0"                                                   \
 273         "mtdparts=mtdparts=davinci_nand.0:"                             \
 274                 "1024k(bootloader)ro,512k(params)ro,-(ubifs)\0"
 275
 276 #define CONFIG_BOOTCOMMAND                                              \
 277         "run init_${boot} get_fdt_${boot} get_mon_${boot} "             \
 278                 "get_kern_${boot} run_mon run_kern"
 279
 280 #define CONFIG_BOOTARGS                                                 \
 281
 282 /* Linux interfacing */
 283 #define CONFIG_OF_BOARD_SETUP
 284
 285 /* Now for the remaining common defines */
 286 #include <configs/ti_armv7_common.h>
 287
 288 /* We wont be loading up OS from SPL for now.. */
 289 #undef CONFIG_SPL_OS_BOOT
 290
 291 /* We do not have MMC support.. yet.. */
 292 #undef CONFIG_SPL_LIBDISK_SUPPORT
 293 #undef CONFIG_SPL_MMC_SUPPORT
 294 #undef CONFIG_SPL_FAT_SUPPORT
 295 #undef CONFIG_SPL_EXT_SUPPORT
 296 #undef CONFIG_MMC
 297 #undef CONFIG_GENERIC_MMC
 298 #undef CONFIG_CMD_MMC
 299
 300 /* And no support for GPIO, yet.. */
 301 #undef CONFIG_SPL_GPIO_SUPPORT
 302
 303 /* we may include files below only after all above definitions */
 304 #include <asm/arch/hardware.h>
 305 #include <asm/arch/clock.h>
 306 #ifndef CONFIG_SOC_K2G
 307 #define CONFIG_SYS_HZ_CLOCK             clk_get_rate(KS2_CLK1_6)
 308 #else
 309 #define CONFIG_SYS_HZ_CLOCK             external_clk[sys_clk]
 310 #endif
 311
 312 #endif /* __CONFIG_KS2_EVM_H */