include/configs/tqma6.h

   1 /*
   2  * Copyright (C) 2013, 2014 Markus Niebel <Markus.Niebel@tq-group.com>
   3  *
   4  * Configuration settings for the TQ Systems TQMa6<Q,S> module.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 #include <linux/kconfig.h>
  13 /* SPL */
  14 /* #if defined(CONFIG_SPL_BUILD) */
  15 /* common IMX6 SPL configuration */
  16 #include "imx6_spl.h"
  17
  18 /* #endif */
  19
  20 /* place code in last 4 MiB of RAM */
  21 #if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
  22 #define CONFIG_SYS_TEXT_BASE            0x2fc00000
  23 #elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
  24 #define CONFIG_SYS_TEXT_BASE            0x4fc00000
  25 #endif
  26
  27 #include "mx6_common.h"
  28
  29 #if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
  30 #define PHYS_SDRAM_SIZE                 (512u * SZ_1M)
  31 #elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
  32 #define PHYS_SDRAM_SIZE                 (1024u * SZ_1M)
  33 #endif
  34
  35 #define CONFIG_MXC_UART
  36
  37 /* SPI */
  38 #define CONFIG_MXC_SPI
  39
  40 /* SPI Flash */
  41
  42 #define TQMA6_SPI_FLASH_SECTOR_SIZE     SZ_64K
  43
  44 #define CONFIG_SF_DEFAULT_BUS   0
  45 #define CONFIG_SF_DEFAULT_CS    0
  46 #define CONFIG_SF_DEFAULT_SPEED 50000000
  47 #define CONFIG_SF_DEFAULT_MODE  (SPI_MODE_0)
  48
  49 /* I2C Configs */
  50 #define CONFIG_SYS_I2C
  51 #define CONFIG_SYS_I2C_MXC
  52 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  53 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  54 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  55 #define CONFIG_I2C_MULTI_BUS
  56 #define CONFIG_SYS_I2C_SPEED            100000
  57
  58 /* I2C SYSMON (LM75) */
  59 #define CONFIG_DTT_LM75
  60 #define CONFIG_DTT_MAX_TEMP             70
  61 #define CONFIG_DTT_MIN_TEMP             -30
  62 #define CONFIG_DTT_HYSTERESIS   3
  63 #define CONFIG_CMD_DTT
  64
  65 /* I2C EEPROM (M24C64) */
  66 #define CONFIG_SYS_I2C_EEPROM_ADDR                      0x50
  67 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN                  2
  68 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS           5 /* 32 Bytes */
  69 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS       20
  70 #define CONFIG_CMD_EEPROM
  71
  72 #define CONFIG_POWER
  73 #define CONFIG_POWER_I2C
  74 #define CONFIG_POWER_PFUZE100
  75 #define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08
  76 #define TQMA6_PFUZE100_I2C_BUS          2
  77
  78 /* MMC Configs */
  79 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  80
  81 /* USB Configs */
  82 #define CONFIG_USB_EHCI
  83 #define CONFIG_USB_EHCI_MX6
  84 #define CONFIG_USB_HOST_ETHER
  85 #define CONFIG_USB_ETHER_SMSC95XX
  86 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  87 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
  88 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET        /* For OTG port */
  89
  90 #define CONFIG_FEC_MXC
  91 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  92 #define CONFIG_PHYLIB
  93 #define CONFIG_MII
  94
  95 #define CONFIG_ARP_TIMEOUT              200UL
  96 /* Network config - Allow larger/faster download for TFTP/NFS */
  97 #define CONFIG_IP_DEFRAG
  98 #define CONFIG_TFTP_BLOCKSIZE   4096
  99 #define CONFIG_NFS_READ_SIZE    4096
 100
 101 /* Command definition */
 102 #define CONFIG_CMD_BMODE
 103
 104 #define CONFIG_ENV_SIZE                 (SZ_8K)
 105 /* Size of malloc() pool */
 106 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 2 * SZ_1M)
 107
 108 #if defined(CONFIG_TQMA6X_MMC_BOOT)
 109
 110 #define CONFIG_ENV_IS_IN_MMC
 111 #define TQMA6_UBOOT_OFFSET              SZ_1K
 112 #define TQMA6_UBOOT_SECTOR_START        0x2
 113 #define TQMA6_UBOOT_SECTOR_COUNT        0x7fe
 114
 115 #define CONFIG_ENV_OFFSET               SZ_1M
 116 #define CONFIG_SYS_MMC_ENV_DEV          0
 117
 118 #define TQMA6_FDT_OFFSET                (2 * SZ_1M)
 119 #define TQMA6_FDT_SECTOR_START          0x1000
 120 #define TQMA6_FDT_SECTOR_COUNT          0x800
 121
 122 #define TQMA6_KERNEL_SECTOR_START       0x2000
 123 #define TQMA6_KERNEL_SECTOR_COUNT       0x2000
 124
 125 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
 126         "uboot_start="__stringify(TQMA6_UBOOT_SECTOR_START)"\0"                \
 127         "uboot_size="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"                 \
 128         "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
 129         "fdt_size="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                     \
 130         "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
 131         "kernel_size="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"               \
 132         "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0"                       \
 133         "loadimage=mmc dev ${mmcdev}; "                                        \
 134                 "mmc read ${loadaddr} ${kernel_start} ${kernel_size};\0"       \
 135         "loadfdt=mmc dev ${mmcdev}; "                                          \
 136                 "mmc read ${fdt_addr} ${fdt_start} ${fdt_size};\0"             \
 137         "update_uboot=if tftp ${uboot}; then "                                 \
 138                 "if itest ${filesize} > 0; then "                              \
 139                         "mmc dev ${mmcdev}; mmc rescan; "                      \
 140                         "setexpr blkc ${filesize} / 0x200; "                   \
 141                         "setexpr blkc ${blkc} + 1; "                           \
 142                         "if itest ${blkc} <= ${uboot_size}; then "             \
 143                                 "mmc write ${loadaddr} ${uboot_start} "        \
 144                                         "${blkc}; "                            \
 145                         "fi; "                                                 \
 146                 "fi; fi; "                                                     \
 147                 "setenv filesize; setenv blkc \0"                              \
 148         "update_kernel=run kernel_name; "                                      \
 149                 "if tftp ${kernel}; then "                                     \
 150                         "if itest ${filesize} > 0; then "                      \
 151                                 "mmc dev ${mmcdev}; mmc rescan; "              \
 152                                 "setexpr blkc ${filesize} / 0x200; "           \
 153                                 "setexpr blkc ${blkc} + 1; "                   \
 154                                 "if itest ${blkc} <= ${kernel_size}; then "    \
 155                                         "mmc write ${loadaddr} "               \
 156                                                 "${kernel_start} ${blkc}; "    \
 157                                 "fi; "                                         \
 158                         "fi; "                                                 \
 159                 "fi; "                                                         \
 160                 "setenv filesize; setenv blkc \0"                              \
 161         "update_fdt=if tftp ${fdt_file}; then "                                \
 162                 "if itest ${filesize} > 0; then "                              \
 163                         "mmc dev ${mmcdev}; mmc rescan; "                      \
 164                         "setexpr blkc ${filesize} / 0x200; "                   \
 165                         "setexpr blkc ${blkc} + 1; "                           \
 166                         "if itest ${blkc} <= ${fdt_size}; then "               \
 167                                 "mmc write ${loadaddr} ${fdt_start} ${blkc}; " \
 168                         "fi; "                                                 \
 169                 "fi; fi; "                                                     \
 170                 "setenv filesize; setenv blkc \0"                              \
 171
 172 #define CONFIG_BOOTCOMMAND \
 173         "run mmcboot; run netboot; run panicboot"
 174
 175 #elif defined(CONFIG_TQMA6X_SPI_BOOT)
 176
 177 #define TQMA6_UBOOT_OFFSET              0x400
 178 #define TQMA6_UBOOT_SECTOR_START        0x0
 179 /* max u-boot size: 512k */
 180 #define TQMA6_UBOOT_SECTOR_SIZE         TQMA6_SPI_FLASH_SECTOR_SIZE
 181 #define TQMA6_UBOOT_SECTOR_COUNT        0x8
 182 #define TQMA6_UBOOT_SIZE                (TQMA6_UBOOT_SECTOR_SIZE * \
 183                                          TQMA6_UBOOT_SECTOR_COUNT)
 184
 185 #define CONFIG_ENV_IS_IN_SPI_FLASH
 186 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
 187 #define CONFIG_ENV_OFFSET               (TQMA6_UBOOT_SIZE)
 188 #define CONFIG_ENV_SECT_SIZE            TQMA6_SPI_FLASH_SECTOR_SIZE
 189 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + \
 190                                          CONFIG_ENV_SECT_SIZE)
 191
 192 #define CONFIG_ENV_SPI_BUS              (CONFIG_SF_DEFAULT_BUS)
 193 #define CONFIG_ENV_SPI_CS               (CONFIG_SF_DEFAULT_CS)
 194 #define CONFIG_ENV_SPI_MAX_HZ           (CONFIG_SF_DEFAULT_SPEED)
 195 #define CONFIG_ENV_SPI_MODE             (CONFIG_SF_DEFAULT_MODE)
 196
 197 #define TQMA6_FDT_OFFSET                (CONFIG_ENV_OFFSET_REDUND + \
 198                                          CONFIG_ENV_SECT_SIZE)
 199 #define TQMA6_FDT_SECT_SIZE             (TQMA6_SPI_FLASH_SECTOR_SIZE)
 200
 201 #define TQMA6_FDT_SECTOR_START          0x0a /* 8 Sector u-boot, 2 Sector env */
 202 #define TQMA6_FDT_SECTOR_COUNT          0x01
 203
 204 #define TQMA6_KERNEL_SECTOR_START       0x10
 205 #define TQMA6_KERNEL_SECTOR_COUNT       0x60
 206
 207 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
 208         "mmcblkdev=0\0"                                                        \
 209         "uboot_offset="__stringify(TQMA6_UBOOT_OFFSET)"\0"                     \
 210         "uboot_sectors="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"              \
 211         "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
 212         "fdt_sectors="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                  \
 213         "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
 214         "kernel_sectors="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"            \
 215         "update_uboot=if tftp ${uboot}; then "                                 \
 216                 "if itest ${filesize} > 0; then "                              \
 217                         "setexpr blkc ${filesize} + "                          \
 218                                 __stringify(TQMA6_UBOOT_OFFSET) "; "           \
 219                         "setexpr size ${uboot_sectors} * "                     \
 220                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 221                         "if itest ${blkc} <= ${size}; then "                   \
 222                                 "sf probe; "                                   \
 223                                 "sf erase 0 ${size}; "                         \
 224                                 "sf write ${loadaddr} ${uboot_offset} "        \
 225                                         "${filesize}; "                        \
 226                         "fi; "                                                 \
 227                 "fi; fi; "                                                     \
 228                 "setenv filesize 0; setenv blkc; setenv size \0"               \
 229         "update_kernel=run kernel_name; if tftp ${kernel}; then "              \
 230                 "if itest ${filesize} > 0; then "                              \
 231                         "setexpr size ${kernel_sectors} * "                    \
 232                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 233                         "setexpr offset ${kernel_start} * "                    \
 234                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 235                         "if itest ${filesize} <= ${size}; then "               \
 236                                 "sf probe; "                                   \
 237                                 "sf erase ${offset} ${size}; "                 \
 238                                 "sf write ${loadaddr} ${offset} "              \
 239                                         "${filesize}; "                        \
 240                         "fi; "                                                 \
 241                 "fi; fi; "                                                     \
 242                 "setenv filesize 0; setenv size ; setenv offset\0"             \
 243         "update_fdt=if tftp ${fdt_file}; then "                                \
 244                 "if itest ${filesize} > 0; then "                              \
 245                         "setexpr size ${fdt_sectors} * "                       \
 246                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 247                         "setexpr offset ${fdt_start} * "                       \
 248                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 249                         "if itest ${filesize} <= ${size}; then "               \
 250                                 "sf probe; "                                   \
 251                                 "sf erase ${offset} ${size}; "                 \
 252                                 "sf write ${loadaddr} ${offset} "              \
 253                                         "${filesize}; "                        \
 254                         "fi; "                                                 \
 255                 "fi; fi; "                                                     \
 256                 "setenv filesize 0; setenv size ; setenv offset\0"             \
 257         "loadimage=sf probe; "                                                 \
 258                 "setexpr size ${kernel_sectors} * "                            \
 259                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 260                 "setexpr offset ${kernel_start} * "                            \
 261                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 262                 "sf read ${loadaddr} ${offset} ${size}; "                      \
 263                 "setenv size ; setenv offset\0"                                \
 264         "loadfdt=sf probe; "                                                   \
 265                 "setexpr size ${fdt_sectors} * "                               \
 266                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 267                 "setexpr offset ${fdt_start} * "                               \
 268                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 269                 "sf read ${${fdt_addr}} ${offset} ${size}; "                   \
 270                 "setenv size ; setenv offset\0"                                \
 271
 272 #define CONFIG_BOOTCOMMAND                                                     \
 273         "sf probe; run mmcboot; run netboot; run panicboot"                    \
 274
 275 #else
 276
 277 #error "need to define boot source"
 278
 279 #endif
 280
 281 /* 128 MiB offset as in ARM related docu for linux suggested */
 282 #define TQMA6_FDT_ADDRESS               0x18000000
 283
 284 #define CONFIG_EXTRA_ENV_SETTINGS                                              \
 285         "board=tqma6\0"                                                        \
 286         "uimage=uImage\0"                                                      \
 287         "zimage=zImage\0"                                                      \
 288         "boot_type=bootz\0"                                                    \
 289         "kernel_name=if test \"${boot_type}\" != bootz; then "                 \
 290                 "setenv kernel ${uimage}; "                                    \
 291                 "else setenv kernel ${zimage}; fi\0"                           \
 292         "uboot=u-boot.imx\0"                                                   \
 293         "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0"                               \
 294         "fdt_addr="__stringify(TQMA6_FDT_ADDRESS)"\0"                          \
 295         "console=" CONSOLE_DEV "\0"                                     \
 296         "fdt_high=0xffffffff\0"                                                \
 297         "initrd_high=0xffffffff\0"                                             \
 298         "addtty=setenv bootargs ${bootargs} console=${console},${baudrate}\0"  \
 299         "addfb=setenv bootargs ${bootargs} "                                   \
 300                 "imx-fbdev.legacyfb_depth=32 consoleblank=0\0"                 \
 301         "mmcpart=2\0"                                                          \
 302         "mmcblkdev=0\0"                                                        \
 303         "mmcargs=run addmmc addtty addfb\0"                                    \
 304         "addmmc=setenv bootargs ${bootargs} "                                  \
 305                 "root=/dev/mmcblk${mmcblkdev}p${mmcpart} rw rootwait\0"        \
 306         "mmcboot=echo Booting from mmc ...; "                                  \
 307                 "setenv bootargs; "                                            \
 308                 "run mmcargs; "                                                \
 309                 "run loadimage; "                                              \
 310                 "if run loadfdt; then "                                        \
 311                         "echo boot device tree kernel ...; "                   \
 312                         "${boot_type} ${loadaddr} - ${fdt_addr}; "             \
 313                 "else "                                                        \
 314                         "${boot_type}; "                                       \
 315                 "fi;\0"                                                        \
 316                 "setenv bootargs \0"                                           \
 317         "netdev=eth0\0"                                                        \
 318         "rootpath=/srv/nfs/tqma6\0"                                            \
 319         "ipmode=static\0"                                                      \
 320         "netargs=run addnfs addip addtty addfb\0"                              \
 321         "addnfs=setenv bootargs ${bootargs} "                                  \
 322                 "root=/dev/nfs rw "                                            \
 323                 "nfsroot=${serverip}:${rootpath},v3,tcp;\0"                    \
 324         "addip_static=setenv bootargs ${bootargs} "                            \
 325                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:"            \
 326                 "${hostname}:${netdev}:off\0"                                  \
 327         "addip_dynamic=setenv bootargs ${bootargs} ip=dhcp\0"                  \
 328         "addip=if test \"${ipmode}\" != static; then "                         \
 329                 "run addip_dynamic; else run addip_static; fi\0"               \
 330         "set_getcmd=if test \"${ipmode}\" != static; then "                    \
 331                 "setenv getcmd dhcp; setenv autoload yes; "                    \
 332                 "else setenv getcmd tftp; setenv autoload no; fi\0"            \
 333         "netboot=echo Booting from net ...; "                                  \
 334                 "run kernel_name; "                                            \
 335                 "run set_getcmd; "                                             \
 336                 "setenv bootargs; "                                            \
 337                 "run netargs; "                                                \
 338                 "if ${getcmd} ${kernel}; then "                                \
 339                         "if ${getcmd} ${fdt_addr} ${fdt_file}; then "          \
 340                                 "${boot_type} ${loadaddr} - ${fdt_addr}; "     \
 341                         "fi; "                                                 \
 342                 "fi; "                                                         \
 343                 "echo ... failed\0"                                            \
 344         "panicboot=echo No boot device !!! reset\0"                            \
 345         TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                      \
 346
 347 #define CONFIG_STACKSIZE                (128u * SZ_1K)
 348
 349 /* Physical Memory Map */
 350 #define CONFIG_NR_DRAM_BANKS            1
 351 #define PHYS_SDRAM                      MMDC0_ARB_BASE_ADDR
 352
 353 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM
 354 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
 355 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
 356
 357 #define CONFIG_SYS_INIT_SP_OFFSET \
 358         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 359 #define CONFIG_SYS_INIT_SP_ADDR \
 360         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 361
 362 /*
 363  * All the defines above are for the TQMa6 SoM
 364  *
 365  * Now include the baseboard specific configuration
 366  */
 367 #ifdef CONFIG_MBA6
 368 #include "tqma6_mba6.h"
 369 #elif CONFIG_WRU4
 370 #include "tqma6_wru4.h"
 371 #else
 372 #error "No baseboard for the TQMa6 defined!"
 373 #endif
 374
 375 /* Support at least the sensor on TQMa6 SOM */
 376 #if !defined(CONFIG_DTT_SENSORS)
 377 #define CONFIG_DTT_SENSORS              { 0 }
 378 #endif
 379
 380 #endif /* __CONFIG_H */