include/configs/tqma6.h

   1 /*
   2  * Copyright (C) 2013, 2014 Markus Niebel <Markus.Niebel@tq-group.com>
   3  *
   4  * Configuration settings for the TQ Systems TQMa6<Q,S> module.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 #include <linux/kconfig.h>
  13 /* SPL */
  14 /* #if defined(CONFIG_SPL_BUILD) */
  15
  16 #define CONFIG_SPL_MMC_SUPPORT
  17 #define CONFIG_SPL_SPI_SUPPORT
  18 #define CONFIG_SPL_FAT_SUPPORT
  19
  20 /* common IMX6 SPL configuration */
  21 #include "imx6_spl.h"
  22
  23 /* #endif */
  24
  25 /* place code in last 4 MiB of RAM */
  26 #if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
  27 #define CONFIG_SYS_TEXT_BASE            0x2fc00000
  28 #elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
  29 #define CONFIG_SYS_TEXT_BASE            0x4fc00000
  30 #endif
  31
  32 #include "mx6_common.h"
  33
  34 #if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
  35 #define PHYS_SDRAM_SIZE                 (512u * SZ_1M)
  36 #elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
  37 #define PHYS_SDRAM_SIZE                 (1024u * SZ_1M)
  38 #endif
  39
  40 #define CONFIG_BOARD_EARLY_INIT_F
  41 #define CONFIG_BOARD_LATE_INIT
  42
  43 #define CONFIG_MXC_UART
  44
  45 /* SPI */
  46 #define CONFIG_MXC_SPI
  47
  48 /* SPI Flash */
  49
  50 #define TQMA6_SPI_FLASH_SECTOR_SIZE     SZ_64K
  51
  52 #define CONFIG_SF_DEFAULT_BUS   0
  53 #define CONFIG_SF_DEFAULT_CS    0
  54 #define CONFIG_SF_DEFAULT_SPEED 50000000
  55 #define CONFIG_SF_DEFAULT_MODE  (SPI_MODE_0)
  56
  57 /* I2C Configs */
  58 #define CONFIG_SYS_I2C
  59 #define CONFIG_SYS_I2C_MXC
  60 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  61 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  62 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  63 #define CONFIG_I2C_MULTI_BUS
  64 #define CONFIG_SYS_I2C_SPEED            100000
  65
  66 /* I2C SYSMON (LM75) */
  67 #define CONFIG_DTT_LM75
  68 #define CONFIG_DTT_MAX_TEMP             70
  69 #define CONFIG_DTT_MIN_TEMP             -30
  70 #define CONFIG_DTT_HYSTERESIS   3
  71 #define CONFIG_CMD_DTT
  72
  73 /* I2C EEPROM (M24C64) */
  74 #define CONFIG_SYS_I2C_EEPROM_ADDR                      0x50
  75 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN                  2
  76 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS           5 /* 32 Bytes */
  77 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS       20
  78 #define CONFIG_CMD_EEPROM
  79
  80 #define CONFIG_POWER
  81 #define CONFIG_POWER_I2C
  82 #define CONFIG_POWER_PFUZE100
  83 #define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08
  84 #define TQMA6_PFUZE100_I2C_BUS          2
  85
  86 /* MMC Configs */
  87 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  88
  89 /* USB Configs */
  90 #define CONFIG_USB_EHCI
  91 #define CONFIG_USB_EHCI_MX6
  92 #define CONFIG_USB_STORAGE
  93 #define CONFIG_USB_HOST_ETHER
  94 #define CONFIG_USB_ETHER_SMSC95XX
  95 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  96 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
  97 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET        /* For OTG port */
  98
  99 #define CONFIG_FEC_MXC
 100 #define IMX_FEC_BASE                    ENET_BASE_ADDR
 101 #define CONFIG_PHYLIB
 102 #define CONFIG_MII
 103
 104 #define CONFIG_ARP_TIMEOUT              200UL
 105 /* Network config - Allow larger/faster download for TFTP/NFS */
 106 #define CONFIG_IP_DEFRAG
 107 #define CONFIG_TFTP_BLOCKSIZE   4096
 108 #define CONFIG_NFS_READ_SIZE    4096
 109
 110 /* Command definition */
 111 #define CONFIG_CMD_BMODE
 112
 113 #define CONFIG_ENV_SIZE                 (SZ_8K)
 114 /* Size of malloc() pool */
 115 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 2 * SZ_1M)
 116
 117 #if defined(CONFIG_TQMA6X_MMC_BOOT)
 118
 119 #define CONFIG_ENV_IS_IN_MMC
 120 #define TQMA6_UBOOT_OFFSET              SZ_1K
 121 #define TQMA6_UBOOT_SECTOR_START        0x2
 122 #define TQMA6_UBOOT_SECTOR_COUNT        0x7fe
 123
 124 #define CONFIG_ENV_OFFSET               SZ_1M
 125 #define CONFIG_SYS_MMC_ENV_DEV          0
 126
 127 #define TQMA6_FDT_OFFSET                (2 * SZ_1M)
 128 #define TQMA6_FDT_SECTOR_START          0x1000
 129 #define TQMA6_FDT_SECTOR_COUNT          0x800
 130
 131 #define TQMA6_KERNEL_SECTOR_START       0x2000
 132 #define TQMA6_KERNEL_SECTOR_COUNT       0x2000
 133
 134 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
 135         "uboot_start="__stringify(TQMA6_UBOOT_SECTOR_START)"\0"                \
 136         "uboot_size="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"                 \
 137         "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
 138         "fdt_size="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                     \
 139         "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
 140         "kernel_size="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"               \
 141         "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0"                       \
 142         "loadimage=mmc dev ${mmcdev}; "                                        \
 143                 "mmc read ${loadaddr} ${kernel_start} ${kernel_size};\0"       \
 144         "loadfdt=mmc dev ${mmcdev}; "                                          \
 145                 "mmc read ${fdt_addr} ${fdt_start} ${fdt_size};\0"             \
 146         "update_uboot=if tftp ${uboot}; then "                                 \
 147                 "if itest ${filesize} > 0; then "                              \
 148                         "mmc dev ${mmcdev}; mmc rescan; "                      \
 149                         "setexpr blkc ${filesize} / 0x200; "                   \
 150                         "setexpr blkc ${blkc} + 1; "                           \
 151                         "if itest ${blkc} <= ${uboot_size}; then "             \
 152                                 "mmc write ${loadaddr} ${uboot_start} "        \
 153                                         "${blkc}; "                            \
 154                         "fi; "                                                 \
 155                 "fi; fi; "                                                     \
 156                 "setenv filesize; setenv blkc \0"                              \
 157         "update_kernel=run kernel_name; "                                      \
 158                 "if tftp ${kernel}; then "                                     \
 159                         "if itest ${filesize} > 0; then "                      \
 160                                 "mmc dev ${mmcdev}; mmc rescan; "              \
 161                                 "setexpr blkc ${filesize} / 0x200; "           \
 162                                 "setexpr blkc ${blkc} + 1; "                   \
 163                                 "if itest ${blkc} <= ${kernel_size}; then "    \
 164                                         "mmc write ${loadaddr} "               \
 165                                                 "${kernel_start} ${blkc}; "    \
 166                                 "fi; "                                         \
 167                         "fi; "                                                 \
 168                 "fi; "                                                         \
 169                 "setenv filesize; setenv blkc \0"                              \
 170         "update_fdt=if tftp ${fdt_file}; then "                                \
 171                 "if itest ${filesize} > 0; then "                              \
 172                         "mmc dev ${mmcdev}; mmc rescan; "                      \
 173                         "setexpr blkc ${filesize} / 0x200; "                   \
 174                         "setexpr blkc ${blkc} + 1; "                           \
 175                         "if itest ${blkc} <= ${fdt_size}; then "               \
 176                                 "mmc write ${loadaddr} ${fdt_start} ${blkc}; " \
 177                         "fi; "                                                 \
 178                 "fi; fi; "                                                     \
 179                 "setenv filesize; setenv blkc \0"                              \
 180
 181 #define CONFIG_BOOTCOMMAND \
 182         "run mmcboot; run netboot; run panicboot"
 183
 184 #elif defined(CONFIG_TQMA6X_SPI_BOOT)
 185
 186 #define TQMA6_UBOOT_OFFSET              0x400
 187 #define TQMA6_UBOOT_SECTOR_START        0x0
 188 /* max u-boot size: 512k */
 189 #define TQMA6_UBOOT_SECTOR_SIZE         TQMA6_SPI_FLASH_SECTOR_SIZE
 190 #define TQMA6_UBOOT_SECTOR_COUNT        0x8
 191 #define TQMA6_UBOOT_SIZE                (TQMA6_UBOOT_SECTOR_SIZE * \
 192                                          TQMA6_UBOOT_SECTOR_COUNT)
 193
 194 #define CONFIG_ENV_IS_IN_SPI_FLASH
 195 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
 196 #define CONFIG_ENV_OFFSET               (TQMA6_UBOOT_SIZE)
 197 #define CONFIG_ENV_SECT_SIZE            TQMA6_SPI_FLASH_SECTOR_SIZE
 198 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + \
 199                                          CONFIG_ENV_SECT_SIZE)
 200
 201 #define CONFIG_ENV_SPI_BUS              (CONFIG_SF_DEFAULT_BUS)
 202 #define CONFIG_ENV_SPI_CS               (CONFIG_SF_DEFAULT_CS)
 203 #define CONFIG_ENV_SPI_MAX_HZ           (CONFIG_SF_DEFAULT_SPEED)
 204 #define CONFIG_ENV_SPI_MODE             (CONFIG_SF_DEFAULT_MODE)
 205
 206 #define TQMA6_FDT_OFFSET                (CONFIG_ENV_OFFSET_REDUND + \
 207                                          CONFIG_ENV_SECT_SIZE)
 208 #define TQMA6_FDT_SECT_SIZE             (TQMA6_SPI_FLASH_SECTOR_SIZE)
 209
 210 #define TQMA6_FDT_SECTOR_START          0x0a /* 8 Sector u-boot, 2 Sector env */
 211 #define TQMA6_FDT_SECTOR_COUNT          0x01
 212
 213 #define TQMA6_KERNEL_SECTOR_START       0x10
 214 #define TQMA6_KERNEL_SECTOR_COUNT       0x60
 215
 216 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
 217         "mmcblkdev=0\0"                                                        \
 218         "uboot_offset="__stringify(TQMA6_UBOOT_OFFSET)"\0"                     \
 219         "uboot_sectors="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"              \
 220         "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
 221         "fdt_sectors="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                  \
 222         "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
 223         "kernel_sectors="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"            \
 224         "update_uboot=if tftp ${uboot}; then "                                 \
 225                 "if itest ${filesize} > 0; then "                              \
 226                         "setexpr blkc ${filesize} + "                          \
 227                                 __stringify(TQMA6_UBOOT_OFFSET) "; "           \
 228                         "setexpr size ${uboot_sectors} * "                     \
 229                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 230                         "if itest ${blkc} <= ${size}; then "                   \
 231                                 "sf probe; "                                   \
 232                                 "sf erase 0 ${size}; "                         \
 233                                 "sf write ${loadaddr} ${uboot_offset} "        \
 234                                         "${filesize}; "                        \
 235                         "fi; "                                                 \
 236                 "fi; fi; "                                                     \
 237                 "setenv filesize 0; setenv blkc; setenv size \0"               \
 238         "update_kernel=run kernel_name; if tftp ${kernel}; then "              \
 239                 "if itest ${filesize} > 0; then "                              \
 240                         "setexpr size ${kernel_sectors} * "                    \
 241                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 242                         "setexpr offset ${kernel_start} * "                    \
 243                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 244                         "if itest ${filesize} <= ${size}; then "               \
 245                                 "sf probe; "                                   \
 246                                 "sf erase ${offset} ${size}; "                 \
 247                                 "sf write ${loadaddr} ${offset} "              \
 248                                         "${filesize}; "                        \
 249                         "fi; "                                                 \
 250                 "fi; fi; "                                                     \
 251                 "setenv filesize 0; setenv size ; setenv offset\0"             \
 252         "update_fdt=if tftp ${fdt_file}; then "                                \
 253                 "if itest ${filesize} > 0; then "                              \
 254                         "setexpr size ${fdt_sectors} * "                       \
 255                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 256                         "setexpr offset ${fdt_start} * "                       \
 257                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 258                         "if itest ${filesize} <= ${size}; then "               \
 259                                 "sf probe; "                                   \
 260                                 "sf erase ${offset} ${size}; "                 \
 261                                 "sf write ${loadaddr} ${offset} "              \
 262                                         "${filesize}; "                        \
 263                         "fi; "                                                 \
 264                 "fi; fi; "                                                     \
 265                 "setenv filesize 0; setenv size ; setenv offset\0"             \
 266         "loadimage=sf probe; "                                                 \
 267                 "setexpr size ${kernel_sectors} * "                            \
 268                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 269                 "setexpr offset ${kernel_start} * "                            \
 270                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 271                 "sf read ${loadaddr} ${offset} ${size}; "                      \
 272                 "setenv size ; setenv offset\0"                                \
 273         "loadfdt=sf probe; "                                                   \
 274                 "setexpr size ${fdt_sectors} * "                               \
 275                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 276                 "setexpr offset ${fdt_start} * "                               \
 277                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 278                 "sf read ${${fdt_addr}} ${offset} ${size}; "                   \
 279                 "setenv size ; setenv offset\0"                                \
 280
 281 #define CONFIG_BOOTCOMMAND                                                     \
 282         "sf probe; run mmcboot; run netboot; run panicboot"                    \
 283
 284 #else
 285
 286 #error "need to define boot source"
 287
 288 #endif
 289
 290 /* 128 MiB offset as in ARM related docu for linux suggested */
 291 #define TQMA6_FDT_ADDRESS               0x18000000
 292
 293 #define CONFIG_EXTRA_ENV_SETTINGS                                              \
 294         "board=tqma6\0"                                                        \
 295         "uimage=uImage\0"                                                      \
 296         "zimage=zImage\0"                                                      \
 297         "boot_type=bootz\0"                                                    \
 298         "kernel_name=if test \"${boot_type}\" != bootz; then "                 \
 299                 "setenv kernel ${uimage}; "                                    \
 300                 "else setenv kernel ${zimage}; fi\0"                           \
 301         "uboot=u-boot.imx\0"                                                   \
 302         "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0"                               \
 303         "fdt_addr="__stringify(TQMA6_FDT_ADDRESS)"\0"                          \
 304         "console=" CONFIG_CONSOLE_DEV "\0"                                     \
 305         "fdt_high=0xffffffff\0"                                                \
 306         "initrd_high=0xffffffff\0"                                             \
 307         "addtty=setenv bootargs ${bootargs} console=${console},${baudrate}\0"  \
 308         "addfb=setenv bootargs ${bootargs} "                                   \
 309                 "imx-fbdev.legacyfb_depth=32 consoleblank=0\0"                 \
 310         "mmcpart=2\0"                                                          \
 311         "mmcblkdev=0\0"                                                        \
 312         "mmcargs=run addmmc addtty addfb\0"                                    \
 313         "addmmc=setenv bootargs ${bootargs} "                                  \
 314                 "root=/dev/mmcblk${mmcblkdev}p${mmcpart} rw rootwait\0"        \
 315         "mmcboot=echo Booting from mmc ...; "                                  \
 316                 "setenv bootargs; "                                            \
 317                 "run mmcargs; "                                                \
 318                 "run loadimage; "                                              \
 319                 "if run loadfdt; then "                                        \
 320                         "echo boot device tree kernel ...; "                   \
 321                         "${boot_type} ${loadaddr} - ${fdt_addr}; "             \
 322                 "else "                                                        \
 323                         "${boot_type}; "                                       \
 324                 "fi;\0"                                                        \
 325                 "setenv bootargs \0"                                           \
 326         "netdev=eth0\0"                                                        \
 327         "rootpath=/srv/nfs/tqma6\0"                                            \
 328         "ipmode=static\0"                                                      \
 329         "netargs=run addnfs addip addtty addfb\0"                              \
 330         "addnfs=setenv bootargs ${bootargs} "                                  \
 331                 "root=/dev/nfs rw "                                            \
 332                 "nfsroot=${serverip}:${rootpath},v3,tcp;\0"                    \
 333         "addip_static=setenv bootargs ${bootargs} "                            \
 334                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:"            \
 335                 "${hostname}:${netdev}:off\0"                                  \
 336         "addip_dynamic=setenv bootargs ${bootargs} ip=dhcp\0"                  \
 337         "addip=if test \"${ipmode}\" != static; then "                         \
 338                 "run addip_dynamic; else run addip_static; fi\0"               \
 339         "set_getcmd=if test \"${ipmode}\" != static; then "                    \
 340                 "setenv getcmd dhcp; setenv autoload yes; "                    \
 341                 "else setenv getcmd tftp; setenv autoload no; fi\0"            \
 342         "netboot=echo Booting from net ...; "                                  \
 343                 "run kernel_name; "                                            \
 344                 "run set_getcmd; "                                             \
 345                 "setenv bootargs; "                                            \
 346                 "run netargs; "                                                \
 347                 "if ${getcmd} ${kernel}; then "                                \
 348                         "if ${getcmd} ${fdt_addr} ${fdt_file}; then "          \
 349                                 "${boot_type} ${loadaddr} - ${fdt_addr}; "     \
 350                         "fi; "                                                 \
 351                 "fi; "                                                         \
 352                 "echo ... failed\0"                                            \
 353         "panicboot=echo No boot device !!! reset\0"                            \
 354         TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                      \
 355
 356 #define CONFIG_STACKSIZE                (128u * SZ_1K)
 357
 358 /* Physical Memory Map */
 359 #define CONFIG_NR_DRAM_BANKS            1
 360 #define PHYS_SDRAM                      MMDC0_ARB_BASE_ADDR
 361
 362 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM
 363 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
 364 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
 365
 366 #define CONFIG_SYS_INIT_SP_OFFSET \
 367         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 368 #define CONFIG_SYS_INIT_SP_ADDR \
 369         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 370
 371 /*
 372  * All the defines above are for the TQMa6 SoM
 373  *
 374  * Now include the baseboard specific configuration
 375  */
 376 #ifdef CONFIG_MBA6
 377 #include "tqma6_mba6.h"
 378 #elif CONFIG_WRU4
 379 #include "tqma6_wru4.h"
 380 #else
 381 #error "No baseboard for the TQMa6 defined!"
 382 #endif
 383
 384 /* Support at least the sensor on TQMa6 SOM */
 385 #if !defined(CONFIG_DTT_SENSORS)
 386 #define CONFIG_DTT_SENSORS              { 0 }
 387 #endif
 388
 389 #endif /* __CONFIG_H */