include/configs/uniphier.h

   1 /*
   2  * Copyright (C) 2012-2015 Masahiro Yamada <yamada.masahiro@socionext.com>
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /* U-boot - Common settings for UniPhier Family */
   8
   9 #ifndef __CONFIG_UNIPHIER_COMMON_H__
  10 #define __CONFIG_UNIPHIER_COMMON_H__
  11
  12 #if defined(CONFIG_MACH_PH1_PRO4)
  13 #define CONFIG_DDR_NUM_CH0 2
  14 #define CONFIG_DDR_NUM_CH1 2
  15
  16 /* Physical start address of SDRAM */
  17 #define CONFIG_SDRAM0_BASE      0x80000000
  18 #define CONFIG_SDRAM0_SIZE      0x20000000
  19 #define CONFIG_SDRAM1_BASE      0xa0000000
  20 #define CONFIG_SDRAM1_SIZE      0x20000000
  21 #endif
  22
  23 #if defined(CONFIG_MACH_PH1_LD4)
  24 #define CONFIG_DDR_NUM_CH0 1
  25 #define CONFIG_DDR_NUM_CH1 1
  26
  27 /* Physical start address of SDRAM */
  28 #define CONFIG_SDRAM0_BASE      0x80000000
  29 #define CONFIG_SDRAM0_SIZE      0x10000000
  30 #define CONFIG_SDRAM1_BASE      0x90000000
  31 #define CONFIG_SDRAM1_SIZE      0x10000000
  32 #endif
  33
  34 #if defined(CONFIG_MACH_PH1_SLD8)
  35 #define CONFIG_DDR_NUM_CH0 1
  36 #define CONFIG_DDR_NUM_CH1 1
  37
  38 /* Physical start address of SDRAM */
  39 #define CONFIG_SDRAM0_BASE      0x80000000
  40 #define CONFIG_SDRAM0_SIZE      0x10000000
  41 #define CONFIG_SDRAM1_BASE      0x90000000
  42 #define CONFIG_SDRAM1_SIZE      0x10000000
  43 #endif
  44
  45 #define CONFIG_I2C_EEPROM
  46 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  10
  47
  48 /*
  49  * Support card address map
  50  */
  51 #if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
  52 # define CONFIG_SUPPORT_CARD_BASE       0x03f00000
  53 # define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
  54 # define CONFIG_SUPPORT_CARD_LED_BASE   (CONFIG_SUPPORT_CARD_BASE + 0x00090000)
  55 # define CONFIG_SUPPORT_CARD_UART_BASE  (CONFIG_SUPPORT_CARD_BASE + 0x000b0000)
  56 #endif
  57
  58 #if defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
  59 # define CONFIG_SUPPORT_CARD_BASE       0x08000000
  60 # define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
  61 # define CONFIG_SUPPORT_CARD_LED_BASE   (CONFIG_SUPPORT_CARD_BASE + 0x00401630)
  62 # define CONFIG_SUPPORT_CARD_UART_BASE  (CONFIG_SUPPORT_CARD_BASE + 0x00200000)
  63 #endif
  64
  65 #ifdef CONFIG_SYS_NS16550_SERIAL
  66 #define CONFIG_SYS_NS16550
  67 #define CONFIG_SYS_NS16550_COM1         CONFIG_SUPPORT_CARD_UART_BASE
  68 #define CONFIG_SYS_NS16550_CLK          12288000
  69 #define CONFIG_SYS_NS16550_REG_SIZE     -2
  70 #endif
  71
  72 /* TODO: move to Kconfig and device tree */
  73 #if 0
  74 #define CONFIG_SYS_NS16550_SERIAL
  75 #endif
  76
  77 #define CONFIG_SMC911X
  78
  79 #define CONFIG_SMC911X_BASE             CONFIG_SUPPORT_CARD_ETHER_BASE
  80 #define CONFIG_SMC911X_32_BIT
  81
  82 /*-----------------------------------------------------------------------
  83  * MMU and Cache Setting
  84  *----------------------------------------------------------------------*/
  85
  86 /* Comment out the following to enable L1 cache */
  87 /* #define CONFIG_SYS_ICACHE_OFF */
  88 /* #define CONFIG_SYS_DCACHE_OFF */
  89
  90 #define CONFIG_SYS_CACHELINE_SIZE       32
  91
  92 /* Comment out the following to enable L2 cache */
  93 #define CONFIG_UNIPHIER_L2CACHE_ON
  94
  95 #define CONFIG_DISPLAY_CPUINFO
  96 #define CONFIG_DISPLAY_BOARDINFO
  97 #define CONFIG_MISC_INIT_F
  98 #define CONFIG_BOARD_EARLY_INIT_F
  99 #define CONFIG_BOARD_EARLY_INIT_R
 100 #define CONFIG_BOARD_LATE_INIT
 101
 102 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 103
 104 #define CONFIG_TIMESTAMP
 105
 106 /* FLASH related */
 107 #define CONFIG_MTD_DEVICE
 108
 109 /*
 110  * uncomment the following to disable FLASH related code.
 111  */
 112 /* #define CONFIG_SYS_NO_FLASH */
 113
 114 #define CONFIG_FLASH_CFI_DRIVER
 115 #define CONFIG_SYS_FLASH_CFI
 116
 117 #define CONFIG_SYS_MAX_FLASH_SECT       256
 118 #define CONFIG_SYS_MONITOR_BASE         0
 119 #define CONFIG_SYS_FLASH_BASE           0
 120
 121 /*
 122  * flash_toggle does not work for out supoort card.
 123  * We need to use flash_status_poll.
 124  */
 125 #define CONFIG_SYS_CFI_FLASH_STATUS_POLL
 126
 127 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 128
 129 #define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2
 130
 131 /* serial console configuration */
 132 #define CONFIG_BAUDRATE                 115200
 133
 134 #define CONFIG_SYS_GENERIC_BOARD
 135
 136 #if !defined(CONFIG_SPL_BUILD)
 137 #define CONFIG_USE_ARCH_MEMSET
 138 #define CONFIG_USE_ARCH_MEMCPY
 139 #endif
 140
 141 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 142
 143 #define CONFIG_CMDLINE_EDITING          /* add command line history     */
 144 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size */
 145 /* Print Buffer Size */
 146 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 147 #define CONFIG_SYS_MAXARGS              16      /* max number of command */
 148 /* Boot Argument Buffer Size */
 149 #define CONFIG_SYS_BARGSIZE             (CONFIG_SYS_CBSIZE)
 150
 151 #define CONFIG_CONS_INDEX               1
 152
 153 /*
 154  * For NAND booting the environment is embedded in the U-Boot image. Please take
 155  * look at the file board/amcc/canyonlands/u-boot-nand.lds for details.
 156  */
 157 /* #define CONFIG_ENV_IS_IN_NAND */
 158 #define CONFIG_ENV_IS_NOWHERE
 159 #define CONFIG_ENV_SIZE                         0x2000
 160 #define CONFIG_ENV_OFFSET                       0x0
 161 /* #define CONFIG_ENV_OFFSET_REDUND     (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */
 162
 163 /* Time clock 1MHz */
 164 #define CONFIG_SYS_TIMER_RATE                   1000000
 165
 166 /*
 167  * By default, ARP timeout is 5 sec.
 168  * The first ARP request does not seem to work.
 169  * So we need to retry ARP request anyway.
 170  * We want to shrink the interval until the second ARP request.
 171  */
 172 #define CONFIG_ARP_TIMEOUT      500UL  /* 0.5 msec */
 173
 174 #define CONFIG_SYS_MAX_NAND_DEVICE                      1
 175 #define CONFIG_SYS_NAND_MAX_CHIPS                       2
 176 #define CONFIG_SYS_NAND_ONFI_DETECTION
 177
 178 #define CONFIG_NAND_DENALI_ECC_SIZE                     1024
 179
 180 #define CONFIG_SYS_NAND_REGS_BASE                       0x68100000
 181 #define CONFIG_SYS_NAND_DATA_BASE                       0x68000000
 182
 183 #define CONFIG_SYS_NAND_BASE            (CONFIG_SYS_NAND_DATA_BASE + 0x10)
 184
 185 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 186 #define CONFIG_SYS_NAND_BAD_BLOCK_POS                   0
 187
 188 /* USB */
 189 #define CONFIG_USB_MAX_CONTROLLER_COUNT         2
 190 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      4
 191 #define CONFIG_CMD_FAT
 192 #define CONFIG_FAT_WRITE
 193 #define CONFIG_DOS_PARTITION
 194
 195 /* memtest works on */
 196 #define CONFIG_SYS_MEMTEST_START        CONFIG_SYS_SDRAM_BASE
 197 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_SDRAM_BASE + 0x01000000)
 198
 199 #define CONFIG_BOOTDELAY                        3
 200 #define CONFIG_ZERO_BOOTDELAY_CHECK     /* check for keypress on bootdelay==0 */
 201
 202 /*
 203  * Network Configuration
 204  */
 205 #define CONFIG_SERVERIP                 192.168.11.1
 206 #define CONFIG_IPADDR                   192.168.11.10
 207 #define CONFIG_GATEWAYIP                192.168.11.1
 208 #define CONFIG_NETMASK                  255.255.255.0
 209
 210 #define CONFIG_LOADADDR                 0x84000000
 211 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 212 #define CONFIG_BOOTFILE                 "fit.itb"
 213
 214 #define CONFIG_CMDLINE_EDITING          /* add command line history     */
 215
 216 #define CONFIG_BOOTCOMMAND              "run $bootmode"
 217
 218 #define CONFIG_ROOTPATH                 "/nfs/root/path"
 219 #define CONFIG_NFSBOOTCOMMAND                                           \
 220         "setenv bootargs $bootargs root=/dev/nfs rw "                   \
 221         "nfsroot=$serverip:$rootpath "                                  \
 222         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \
 223         "tftpboot; bootm;"
 224
 225 #define CONFIG_BOOTARGS         " user_debug=0x1f init=/sbin/init"
 226
 227 #define CONFIG_EXTRA_ENV_SETTINGS               \
 228         "netdev=eth0\0"                         \
 229         "image_offset=0x00080000\0"             \
 230         "image_size=0x00f00000\0"               \
 231         "verify=n\0"                            \
 232         "nandupdate=nand erase 0 0x100000 &&"                           \
 233                    "tftpboot u-boot-spl.bin &&"                         \
 234                    "nand write $loadaddr 0 0x10000 &&"                  \
 235                    "tftpboot u-boot-dtb.img &&"                         \
 236                    "nand write $loadaddr 0x10000 0xf0000\0"             \
 237         "norboot=run add_default_bootargs &&"                           \
 238                 "bootm $image_offset\0"                                 \
 239         "nandboot=run add_default_bootargs &&"                          \
 240                  "nand read $loadaddr $image_offset $image_size &&"     \
 241                  "bootm\0"                                              \
 242         "add_default_bootargs=setenv bootargs $bootargs"                \
 243                 " console=ttyS0,$baudrate\0"                            \
 244
 245 /* Open Firmware flat tree */
 246 #define CONFIG_OF_LIBFDT
 247
 248 #define CONFIG_HAVE_ARM_SECURE
 249
 250 /* Memory Size & Mapping */
 251 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SDRAM0_BASE
 252
 253 #if CONFIG_SDRAM0_BASE + CONFIG_SDRAM0_SIZE >= CONFIG_SDRAM1_BASE
 254 /* Thre is no memory hole */
 255 #define CONFIG_NR_DRAM_BANKS            1
 256 #define CONFIG_SYS_SDRAM_SIZE   (CONFIG_SDRAM0_SIZE + CONFIG_SDRAM1_SIZE)
 257 #else
 258 #define CONFIG_NR_DRAM_BANKS            2
 259 #define CONFIG_SYS_SDRAM_SIZE   (CONFIG_SDRAM0_SIZE)
 260 #endif
 261
 262 #if defined(CONFIG_MACH_PH1_LD4) || defined(CONFIG_MACH_PH1_SLD8)
 263 #define CONFIG_SPL_TEXT_BASE            0x00040000
 264 #endif
 265 #if defined(CONFIG_MACH_PH1_PRO4)
 266 #define CONFIG_SPL_TEXT_BASE            0x00100000
 267 #endif
 268
 269 #define CONFIG_SPL_STACK                (0x0ff08000)
 270 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_TEXT_BASE)
 271
 272 #define CONFIG_PANIC_HANG
 273
 274 #define CONFIG_SPL_FRAMEWORK
 275 #define CONFIG_SPL_SERIAL_SUPPORT
 276 #define CONFIG_SPL_NAND_SUPPORT
 277
 278 #define CONFIG_SPL_LIBCOMMON_SUPPORT    /* for mem_malloc_init */
 279 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 280
 281 #define CONFIG_SPL_BOARD_INIT
 282
 283 #define CONFIG_SYS_NAND_U_BOOT_OFFS             0x10000
 284
 285 #define CONFIG_SPL_MAX_FOOTPRINT                0x10000
 286
 287 #endif /* __CONFIG_UNIPHIER_COMMON_H__ */