include/configs/vct.h

   1 /*
   2  * (C) Copyright 2008 Stefan Roese <sr@denx.de>, DENX Software Engineering
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /*
   8  * This file contains the configuration parameters for the VCT board
   9  * family:
  10  *
  11  * vct_premium
  12  * vct_premium_small
  13  * vct_premium_onenand
  14  * vct_premium_onenand_small
  15  * vct_platinum
  16  * vct_platinum_small
  17  * vct_platinum_onenand
  18  * vct_platinum_onenand_small
  19  * vct_platinumavc
  20  * vct_platinumavc_small
  21  * vct_platinumavc_onenand
  22  * vct_platinumavc_onenand_small
  23  */
  24
  25 #ifndef __CONFIG_H
  26 #define __CONFIG_H
  27
  28 #define CPU_CLOCK_RATE                  324000000 /* Clock for the MIPS core */
  29 #define CONFIG_SYS_MIPS_TIMER_FREQ      (CPU_CLOCK_RATE / 2)
  30
  31 #define CONFIG_SKIP_LOWLEVEL_INIT       /* SDRAM is initialized by the bootstrap code */
  32
  33 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
  34 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)
  35 #define CONFIG_SYS_MALLOC_LEN           (1 << 20)
  36 #define CONFIG_SYS_BOOTPARAMS_LEN       (128 << 10)
  37 #define CONFIG_SYS_INIT_SP_OFFSET       0x400000
  38
  39 #if !defined(CONFIG_VCT_NAND) && !defined(CONFIG_VCT_ONENAND)
  40 #define CONFIG_VCT_NOR
  41 #endif
  42
  43 /*
  44  * UART
  45  */
  46 #ifdef CONFIG_VCT_PLATINUMAVC
  47 #define UART_1_BASE             0xBDC30000
  48 #else
  49 #define UART_1_BASE             0xBF89C000
  50 #endif
  51
  52 #define CONFIG_SYS_NS16550_SERIAL
  53 #define CONFIG_SYS_NS16550_REG_SIZE     -4
  54 #define CONFIG_SYS_NS16550_COM1         UART_1_BASE
  55 #define CONFIG_CONS_INDEX               1
  56 #define CONFIG_SYS_NS16550_CLK          921600
  57
  58 /*
  59  * SDRAM
  60  */
  61 #define CONFIG_SYS_SDRAM_BASE           0x80000000
  62 #define CONFIG_SYS_MBYTES_SDRAM         128
  63 #define CONFIG_SYS_MEMTEST_START        0x80200000
  64 #define CONFIG_SYS_MEMTEST_END          0x80400000
  65 #define CONFIG_SYS_LOAD_ADDR            0x80400000      /* default load address */
  66
  67 #if defined(CONFIG_VCT_PREMIUM) || defined(CONFIG_VCT_PLATINUM)
  68 /*
  69  * SMSC91C11x Network Card
  70  */
  71 #define CONFIG_SMC911X
  72 #define CONFIG_SMC911X_BASE     0x00000000
  73 #define CONFIG_SMC911X_32_BIT
  74 #define CONFIG_NET_RETRY_COUNT          20
  75 #endif
  76
  77 /*
  78  * Commands
  79  */
  80 #define CONFIG_CMD_EEPROM
  81
  82 /*
  83  * Only Premium/Platinum have ethernet support right now
  84  */
  85 #if (defined(CONFIG_VCT_PREMIUM) || defined(CONFIG_VCT_PLATINUM)) && \
  86         !defined(CONFIG_VCT_SMALL_IMAGE)
  87 #endif
  88
  89 /*
  90  * Only Premium/Platinum have USB-EHCI support right now
  91  */
  92 #if (defined(CONFIG_VCT_PREMIUM) || defined(CONFIG_VCT_PLATINUM)) && \
  93         !defined(CONFIG_VCT_SMALL_IMAGE)
  94 #endif
  95
  96 #if defined(CONFIG_CMD_USB)
  97 #define CONFIG_SUPPORT_VFAT
  98
  99 /*
 100  * USB/EHCI
 101  */
 102 #define CONFIG_USB_EHCI_VCT             /* on VCT platform              */
 103 #define CONFIG_EHCI_MMIO_BIG_ENDIAN
 104 #define CONFIG_EHCI_DESC_BIG_ENDIAN
 105 #define CONFIG_EHCI_IS_TDI
 106 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* re-init HCD after CMD_RESET */
 107 #endif /* CONFIG_CMD_USB */
 108
 109 #if defined(CONFIG_VCT_NAND)
 110 #define CONFIG_CMD_NAND
 111 #endif
 112
 113 #if defined(CONFIG_VCT_ONENAND)
 114 #define CONFIG_CMD_ONENAND
 115 #endif
 116
 117 /*
 118  * BOOTP options
 119  */
 120 #define CONFIG_BOOTP_BOOTFILESIZE
 121 #define CONFIG_BOOTP_BOOTPATH
 122 #define CONFIG_BOOTP_GATEWAY
 123 #define CONFIG_BOOTP_HOSTNAME
 124 #define CONFIG_BOOTP_SUBNETMASK
 125
 126 /*
 127  * Miscellaneous configurable options
 128  */
 129 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
 130 #define CONFIG_SYS_CBSIZE       512             /* Console I/O Buffer Size      */
 131 #define CONFIG_SYS_PBSIZE       (CONFIG_SYS_CBSIZE + \
 132                                  sizeof(CONFIG_SYS_PROMPT) + 16)
 133 #define CONFIG_SYS_MAXARGS      16              /* max number of command args   */
 134 #define CONFIG_TIMESTAMP                        /* Print image info with timestamp */
 135 #define CONFIG_CMDLINE_EDITING                  /* add command line history     */
 136
 137 /*
 138  * FLASH and environment organization
 139  */
 140 #if defined(CONFIG_VCT_NOR)
 141 #define CONFIG_ENV_IS_IN_FLASH
 142 #define CONFIG_FLASH_NOT_MEM_MAPPED
 143
 144 /*
 145  * We need special accessor functions for the CFI FLASH driver. This
 146  * can be enabled via the CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS option.
 147  */
 148 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
 149
 150 /*
 151  * For the non-memory-mapped NOR FLASH, we need to define the
 152  * NOR FLASH area. This can't be detected via the addr2info()
 153  * function, since we check for flash access in the very early
 154  * U-Boot code, before the NOR FLASH is detected.
 155  */
 156 #define CONFIG_FLASH_BASE               0xb0000000
 157 #define CONFIG_FLASH_END                0xbfffffff
 158
 159 /*
 160  * CFI driver settings
 161  */
 162 #define CONFIG_SYS_FLASH_CFI                    /* The flash is CFI compatible  */
 163 #define CONFIG_FLASH_CFI_DRIVER         /* Use common CFI driver        */
 164 #define CONFIG_SYS_FLASH_CFI_AMD_RESET  1       /* Use AMD (Spansion) reset cmd */
 165 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT /* no byte writes on IXP4xx     */
 166
 167 #define CONFIG_SYS_FLASH_BASE           0xb0000000
 168 #define CONFIG_SYS_FLASH_BANKS_LIST    { CONFIG_SYS_FLASH_BASE }
 169 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max number of memory banks           */
 170 #define CONFIG_SYS_MAX_FLASH_SECT       512     /* max number of sectors on one chip    */
 171
 172 #define CONFIG_SYS_FLASH_ERASE_TOUT     120000  /* Timeout for Flash Erase (in ms)      */
 173 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Timeout for Flash Write (in ms)      */
 174
 175 #ifdef CONFIG_ENV_IS_IN_FLASH
 176 #define CONFIG_ENV_SECT_SIZE    0x10000         /* size of one complete sector  */
 177 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
 178 #define CONFIG_ENV_SIZE         0x4000  /* Total Size of Environment Sector     */
 179
 180 /* Address and size of Redundant Environment Sector     */
 181 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 182 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 183 #endif /* CONFIG_ENV_IS_IN_FLASH */
 184 #endif /* CONFIG_VCT_NOR */
 185
 186 #if defined(CONFIG_VCT_ONENAND)
 187 #define CONFIG_USE_ONENAND_BOARD_INIT
 188 #define CONFIG_ENV_IS_IN_ONENAND
 189 #define CONFIG_SYS_ONENAND_BASE         0x00000000      /* this is not real address */
 190 #define CONFIG_SYS_FLASH_BASE           0x00000000
 191 #define CONFIG_ENV_ADDR                 (128 << 10)     /* after compr. U-Boot image */
 192 #define CONFIG_ENV_SIZE                 (128 << 10)     /* erase size */
 193 #endif /* CONFIG_VCT_ONENAND */
 194
 195 /*
 196  * I2C/EEPROM
 197  */
 198 #define CONFIG_SYS_I2C
 199 #define CONFIG_SYS_I2C_SOFT             /* I2C bit-banged */
 200 #define CONFIG_SYS_I2C_SOFT_SPEED       83000   /* 83 kHz is supposed to work */
 201 #define CONFIG_SYS_I2C_SOFT_SLAVE       0x7f
 202
 203 /*
 204  * Software (bit-bang) I2C driver configuration
 205  */
 206 #define CONFIG_SYS_GPIO_I2C_SCL         11
 207 #define CONFIG_SYS_GPIO_I2C_SDA         10
 208
 209 #ifndef __ASSEMBLY__
 210 int vct_gpio_dir(int pin, int dir);
 211 void vct_gpio_set(int pin, int val);
 212 int vct_gpio_get(int pin);
 213 #endif
 214
 215 #define I2C_INIT        vct_gpio_dir(CONFIG_SYS_GPIO_I2C_SCL, 1)
 216 #define I2C_ACTIVE      vct_gpio_dir(CONFIG_SYS_GPIO_I2C_SDA, 1)
 217 #define I2C_TRISTATE    vct_gpio_dir(CONFIG_SYS_GPIO_I2C_SDA, 0)
 218 #define I2C_READ        vct_gpio_get(CONFIG_SYS_GPIO_I2C_SDA)
 219 #define I2C_SDA(bit)    vct_gpio_set(CONFIG_SYS_GPIO_I2C_SDA, bit)
 220 #define I2C_SCL(bit)    vct_gpio_set(CONFIG_SYS_GPIO_I2C_SCL, bit)
 221 #define I2C_DELAY       udelay(5)       /* 1/4 I2C clock duration */
 222
 223 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
 224 /* CAT24WC32 */
 225 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2       /* Bytes of address             */
 226 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5     /* The Catalyst CAT24WC32 has   */
 227                                         /* 32 byte page write mode using*/
 228                                         /* last 5 bits of the address   */
 229 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10   /* and takes up to 10 msec */
 230
 231 #define CONFIG_BOOTCOMMAND      "run test3"
 232
 233 /*
 234  * UBI configuration
 235  */
 236 #if defined(CONFIG_VCT_ONENAND)
 237 #define CONFIG_SYS_USE_UBI
 238 #define CONFIG_CMD_JFFS2
 239 #define CONFIG_RBTREE
 240 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
 241 #define CONFIG_MTD_PARTITIONS
 242 #define CONFIG_CMD_MTDPARTS
 243
 244 #define MTDIDS_DEFAULT          "onenand0=onenand"
 245 #define MTDPARTS_DEFAULT        "mtdparts=onenand:128k(u-boot),"        \
 246                                         "128k(env),"            \
 247                                         "20m(kernel),"          \
 248                                         "-(rootfs)"
 249 #endif
 250
 251 /*
 252  * We need a small, stripped down image to fit into the first 128k OneNAND
 253  * erase block (gzipped). This image only needs basic commands for FLASH
 254  * (NOR/OneNAND) usage and Linux kernel booting.
 255  */
 256 #if defined(CONFIG_VCT_SMALL_IMAGE)
 257 #undef CONFIG_CMD_EEPROM
 258 #undef CONFIG_CMD_EEPROM
 259 #undef CONFIG_CMD_IRQ
 260 #undef CONFIG_CMD_LOADY
 261 #undef CONFIG_CMD_REGINFO
 262 #undef CONFIG_CMD_STRINGS
 263 #undef CONFIG_CMD_TERMINAL
 264
 265 #undef CONFIG_SMC911X
 266 #undef CONFIG_SYS_I2C_SOFT
 267 #undef CONFIG_SOURCE
 268 #undef CONFIG_SYS_LONGHELP
 269 #undef CONFIG_TIMESTAMP
 270 #endif /* CONFIG_VCT_SMALL_IMAGE */
 271
 272 #endif  /* __CONFIG_H */