include/configs/vct.h

   1 /*
   2  * (C) Copyright 2008 Stefan Roese <sr@denx.de>, DENX Software Engineering
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /*
   8  * This file contains the configuration parameters for the VCT board
   9  * family:
  10  *
  11  * vct_premium
  12  * vct_premium_small
  13  * vct_premium_onenand
  14  * vct_premium_onenand_small
  15  * vct_platinum
  16  * vct_platinum_small
  17  * vct_platinum_onenand
  18  * vct_platinum_onenand_small
  19  * vct_platinumavc
  20  * vct_platinumavc_small
  21  * vct_platinumavc_onenand
  22  * vct_platinumavc_onenand_small
  23  */
  24
  25 #ifndef __CONFIG_H
  26 #define __CONFIG_H
  27
  28 #define CPU_CLOCK_RATE                  324000000 /* Clock for the MIPS core */
  29 #define CONFIG_SYS_MIPS_TIMER_FREQ      (CPU_CLOCK_RATE / 2)
  30
  31 #define CONFIG_SKIP_LOWLEVEL_INIT       /* SDRAM is initialized by the bootstrap code */
  32
  33 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
  34 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)
  35 #define CONFIG_SYS_MALLOC_LEN           (1 << 20)
  36 #define CONFIG_SYS_BOOTPARAMS_LEN       (128 << 10)
  37 #define CONFIG_SYS_INIT_SP_OFFSET       0x400000
  38
  39 #if !defined(CONFIG_VCT_NAND) && !defined(CONFIG_VCT_ONENAND)
  40 #define CONFIG_VCT_NOR
  41 #else
  42 #define CONFIG_SYS_NO_FLASH
  43 #endif
  44
  45 /*
  46  * UART
  47  */
  48 #ifdef CONFIG_VCT_PLATINUMAVC
  49 #define UART_1_BASE             0xBDC30000
  50 #else
  51 #define UART_1_BASE             0xBF89C000
  52 #endif
  53
  54 #define CONFIG_SYS_NS16550_SERIAL
  55 #define CONFIG_SYS_NS16550_REG_SIZE     -4
  56 #define CONFIG_SYS_NS16550_COM1         UART_1_BASE
  57 #define CONFIG_CONS_INDEX               1
  58 #define CONFIG_SYS_NS16550_CLK          921600
  59 #define CONFIG_BAUDRATE                 115200
  60
  61 /*
  62  * SDRAM
  63  */
  64 #define CONFIG_SYS_SDRAM_BASE           0x80000000
  65 #define CONFIG_SYS_MBYTES_SDRAM         128
  66 #define CONFIG_SYS_MEMTEST_START        0x80200000
  67 #define CONFIG_SYS_MEMTEST_END          0x80400000
  68 #define CONFIG_SYS_LOAD_ADDR            0x80400000      /* default load address */
  69
  70 #if defined(CONFIG_VCT_PREMIUM) || defined(CONFIG_VCT_PLATINUM)
  71 /*
  72  * SMSC91C11x Network Card
  73  */
  74 #define CONFIG_SMC911X
  75 #define CONFIG_SMC911X_BASE     0x00000000
  76 #define CONFIG_SMC911X_32_BIT
  77 #define CONFIG_NET_RETRY_COUNT          20
  78 #endif
  79
  80 /*
  81  * Commands
  82  */
  83 #define CONFIG_CMD_EEPROM
  84
  85 /*
  86  * Only Premium/Platinum have ethernet support right now
  87  */
  88 #if (defined(CONFIG_VCT_PREMIUM) || defined(CONFIG_VCT_PLATINUM)) && \
  89         !defined(CONFIG_VCT_SMALL_IMAGE)
  90 #endif
  91
  92 /*
  93  * Only Premium/Platinum have USB-EHCI support right now
  94  */
  95 #if (defined(CONFIG_VCT_PREMIUM) || defined(CONFIG_VCT_PLATINUM)) && \
  96         !defined(CONFIG_VCT_SMALL_IMAGE)
  97 #endif
  98
  99 #if defined(CONFIG_CMD_USB)
 100 #define CONFIG_DOS_PARTITION
 101 #define CONFIG_ISO_PARTITION
 102
 103 #define CONFIG_SUPPORT_VFAT
 104
 105 /*
 106  * USB/EHCI
 107  */
 108 #define CONFIG_USB_EHCI                 /* Enable EHCI USB support      */
 109 #define CONFIG_USB_EHCI_VCT             /* on VCT platform              */
 110 #define CONFIG_EHCI_MMIO_BIG_ENDIAN
 111 #define CONFIG_EHCI_DESC_BIG_ENDIAN
 112 #define CONFIG_EHCI_IS_TDI
 113 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* re-init HCD after CMD_RESET */
 114 #endif /* CONFIG_CMD_USB */
 115
 116 #if defined(CONFIG_VCT_NAND)
 117 #define CONFIG_CMD_NAND
 118 #endif
 119
 120 #if defined(CONFIG_VCT_ONENAND)
 121 #define CONFIG_CMD_ONENAND
 122 #endif
 123
 124 /*
 125  * BOOTP options
 126  */
 127 #define CONFIG_BOOTP_BOOTFILESIZE
 128 #define CONFIG_BOOTP_BOOTPATH
 129 #define CONFIG_BOOTP_GATEWAY
 130 #define CONFIG_BOOTP_HOSTNAME
 131 #define CONFIG_BOOTP_SUBNETMASK
 132
 133 /*
 134  * Miscellaneous configurable options
 135  */
 136 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
 137 #define CONFIG_SYS_CBSIZE       512             /* Console I/O Buffer Size      */
 138 #define CONFIG_SYS_PBSIZE       (CONFIG_SYS_CBSIZE + \
 139                                  sizeof(CONFIG_SYS_PROMPT) + 16)
 140 #define CONFIG_SYS_MAXARGS      16              /* max number of command args   */
 141 #define CONFIG_TIMESTAMP                        /* Print image info with timestamp */
 142 #define CONFIG_CMDLINE_EDITING                  /* add command line history     */
 143 #define CONFIG_SYS_CONSOLE_INFO_QUIET           /* don't print console @ startup*/
 144
 145 /*
 146  * FLASH and environment organization
 147  */
 148 #if defined(CONFIG_VCT_NOR)
 149 #define CONFIG_ENV_IS_IN_FLASH
 150 #define CONFIG_FLASH_NOT_MEM_MAPPED
 151
 152 /*
 153  * We need special accessor functions for the CFI FLASH driver. This
 154  * can be enabled via the CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS option.
 155  */
 156 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
 157
 158 /*
 159  * For the non-memory-mapped NOR FLASH, we need to define the
 160  * NOR FLASH area. This can't be detected via the addr2info()
 161  * function, since we check for flash access in the very early
 162  * U-Boot code, before the NOR FLASH is detected.
 163  */
 164 #define CONFIG_FLASH_BASE               0xb0000000
 165 #define CONFIG_FLASH_END                0xbfffffff
 166
 167 /*
 168  * CFI driver settings
 169  */
 170 #define CONFIG_SYS_FLASH_CFI                    /* The flash is CFI compatible  */
 171 #define CONFIG_FLASH_CFI_DRIVER         /* Use common CFI driver        */
 172 #define CONFIG_SYS_FLASH_CFI_AMD_RESET  1       /* Use AMD (Spansion) reset cmd */
 173 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT /* no byte writes on IXP4xx     */
 174
 175 #define CONFIG_SYS_FLASH_BASE           0xb0000000
 176 #define CONFIG_SYS_FLASH_BANKS_LIST    { CONFIG_SYS_FLASH_BASE }
 177 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max number of memory banks           */
 178 #define CONFIG_SYS_MAX_FLASH_SECT       512     /* max number of sectors on one chip    */
 179
 180 #define CONFIG_SYS_FLASH_ERASE_TOUT     120000  /* Timeout for Flash Erase (in ms)      */
 181 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Timeout for Flash Write (in ms)      */
 182
 183 #ifdef CONFIG_ENV_IS_IN_FLASH
 184 #define CONFIG_ENV_SECT_SIZE    0x10000         /* size of one complete sector  */
 185 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
 186 #define CONFIG_ENV_SIZE         0x4000  /* Total Size of Environment Sector     */
 187
 188 /* Address and size of Redundant Environment Sector     */
 189 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 190 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 191 #endif /* CONFIG_ENV_IS_IN_FLASH */
 192 #endif /* CONFIG_VCT_NOR */
 193
 194 #if defined(CONFIG_VCT_ONENAND)
 195 #define CONFIG_USE_ONENAND_BOARD_INIT
 196 #define CONFIG_ENV_IS_IN_ONENAND
 197 #define CONFIG_SYS_ONENAND_BASE         0x00000000      /* this is not real address */
 198 #define CONFIG_SYS_FLASH_BASE           0x00000000
 199 #define CONFIG_ENV_ADDR                 (128 << 10)     /* after compr. U-Boot image */
 200 #define CONFIG_ENV_SIZE                 (128 << 10)     /* erase size */
 201 #endif /* CONFIG_VCT_ONENAND */
 202
 203 /*
 204  * I2C/EEPROM
 205  */
 206 #define CONFIG_SYS_I2C
 207 #define CONFIG_SYS_I2C_SOFT             /* I2C bit-banged */
 208 #define CONFIG_SYS_I2C_SOFT_SPEED       83000   /* 83 kHz is supposed to work */
 209 #define CONFIG_SYS_I2C_SOFT_SLAVE       0x7f
 210
 211 /*
 212  * Software (bit-bang) I2C driver configuration
 213  */
 214 #define CONFIG_SYS_GPIO_I2C_SCL         11
 215 #define CONFIG_SYS_GPIO_I2C_SDA         10
 216
 217 #ifndef __ASSEMBLY__
 218 int vct_gpio_dir(int pin, int dir);
 219 void vct_gpio_set(int pin, int val);
 220 int vct_gpio_get(int pin);
 221 #endif
 222
 223 #define I2C_INIT        vct_gpio_dir(CONFIG_SYS_GPIO_I2C_SCL, 1)
 224 #define I2C_ACTIVE      vct_gpio_dir(CONFIG_SYS_GPIO_I2C_SDA, 1)
 225 #define I2C_TRISTATE    vct_gpio_dir(CONFIG_SYS_GPIO_I2C_SDA, 0)
 226 #define I2C_READ        vct_gpio_get(CONFIG_SYS_GPIO_I2C_SDA)
 227 #define I2C_SDA(bit)    vct_gpio_set(CONFIG_SYS_GPIO_I2C_SDA, bit)
 228 #define I2C_SCL(bit)    vct_gpio_set(CONFIG_SYS_GPIO_I2C_SCL, bit)
 229 #define I2C_DELAY       udelay(5)       /* 1/4 I2C clock duration */
 230
 231 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
 232 /* CAT24WC32 */
 233 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2       /* Bytes of address             */
 234 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5     /* The Catalyst CAT24WC32 has   */
 235                                         /* 32 byte page write mode using*/
 236                                         /* last 5 bits of the address   */
 237 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10   /* and takes up to 10 msec */
 238
 239 #define CONFIG_BOOTCOMMAND      "run test3"
 240
 241 /*
 242  * UBI configuration
 243  */
 244 #if defined(CONFIG_VCT_ONENAND)
 245 #define CONFIG_SYS_USE_UBI
 246 #define CONFIG_CMD_JFFS2
 247 #define CONFIG_RBTREE
 248 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
 249 #define CONFIG_MTD_PARTITIONS
 250 #define CONFIG_CMD_MTDPARTS
 251
 252 #define MTDIDS_DEFAULT          "onenand0=onenand"
 253 #define MTDPARTS_DEFAULT        "mtdparts=onenand:128k(u-boot),"        \
 254                                         "128k(env),"            \
 255                                         "20m(kernel),"          \
 256                                         "-(rootfs)"
 257 #endif
 258
 259 /*
 260  * We need a small, stripped down image to fit into the first 128k OneNAND
 261  * erase block (gzipped). This image only needs basic commands for FLASH
 262  * (NOR/OneNAND) usage and Linux kernel booting.
 263  */
 264 #if defined(CONFIG_VCT_SMALL_IMAGE)
 265 #undef CONFIG_CMD_BEDBUG
 266 #undef CONFIG_CMD_EEPROM
 267 #undef CONFIG_CMD_EEPROM
 268 #undef CONFIG_CMD_IRQ
 269 #undef CONFIG_CMD_LOADY
 270 #undef CONFIG_CMD_REGINFO
 271 #undef CONFIG_CMD_STRINGS
 272 #undef CONFIG_CMD_TERMINAL
 273
 274 #undef CONFIG_SMC911X
 275 #undef CONFIG_SYS_I2C_SOFT
 276 #undef CONFIG_SOURCE
 277 #undef CONFIG_SYS_LONGHELP
 278 #undef CONFIG_TIMESTAMP
 279 #endif /* CONFIG_VCT_SMALL_IMAGE */
 280
 281 #endif  /* __CONFIG_H */