include/configs/xilinx_zynqmp.h

   1 /*
   2  * Configuration for Xilinx ZynqMP
   3  * (C) Copyright 2014 - 2015 Xilinx, Inc.
   4  * Michal Simek <michal.simek@xilinx.com>
   5  *
   6  * Based on Configuration for Versatile Express
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 #ifndef __XILINX_ZYNQMP_H
  12 #define __XILINX_ZYNQMP_H
  13
  14 #define CONFIG_REMAKE_ELF
  15
  16 /* #define CONFIG_ARMV8_SWITCH_TO_EL1 */
  17
  18 #define CONFIG_SYS_NO_FLASH
  19
  20 /* Generic Interrupt Controller Definitions */
  21 #define CONFIG_GICV2
  22 #define GICD_BASE       0xF9010000
  23 #define GICC_BASE       0xF9020000
  24
  25 #define CONFIG_SYS_ALT_MEMTEST
  26 #define CONFIG_SYS_MEMTEST_SCRATCH      0xfffc0000
  27
  28 #ifndef CONFIG_NR_DRAM_BANKS
  29 # define CONFIG_NR_DRAM_BANKS           2
  30 #endif
  31 #define CONFIG_SYS_MEMTEST_START        0
  32 #define CONFIG_SYS_MEMTEST_END          1000
  33
  34 /* Have release address at the end of 256MB for now */
  35 #define CPU_RELEASE_ADDR        0xFFFFFF0
  36
  37 #define CONFIG_SYS_INIT_SP_ADDR         CONFIG_SYS_TEXT_BASE
  38
  39 /* Generic Timer Definitions - setup in EL3. Setup by ATF for other cases */
  40 #if !defined(COUNTER_FREQUENCY)
  41 # define COUNTER_FREQUENCY              100000000
  42 #endif
  43
  44 /* Size of malloc() pool */
  45 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 0x2000000)
  46
  47 /* Serial setup */
  48 #define CONFIG_ARM_DCC
  49 #define CONFIG_CPU_ARMV8
  50 #define CONFIG_ZYNQ_SERIAL
  51
  52 #define CONFIG_CONS_INDEX               0
  53 #define CONFIG_BAUDRATE                 115200
  54 #define CONFIG_SYS_BAUDRATE_TABLE \
  55         { 4800, 9600, 19200, 38400, 57600, 115200 }
  56
  57 /* Command line configuration */
  58 #define CONFIG_CMD_ENV
  59 #define CONFIG_DOS_PARTITION
  60 #define CONFIG_EFI_PARTITION
  61 #ifndef CONFIG_SPL_BUILD
  62 # define CONFIG_ISO_PARTITION
  63 #endif
  64 #define CONFIG_MP
  65
  66 /* BOOTP options */
  67 #define CONFIG_BOOTP_BOOTFILESIZE
  68 #define CONFIG_BOOTP_BOOTPATH
  69 #define CONFIG_BOOTP_GATEWAY
  70 #define CONFIG_BOOTP_HOSTNAME
  71 #define CONFIG_BOOTP_MAY_FAIL
  72 #define CONFIG_BOOTP_DNS
  73 #define CONFIG_BOOTP_PXE
  74 #define CONFIG_BOOTP_SUBNETMASK
  75
  76 /* Diff from config_distro_defaults.h */
  77 #define CONFIG_SUPPORT_RAW_INITRD
  78 #define CONFIG_ENV_VARS_UBOOT_CONFIG
  79 #define CONFIG_AUTO_COMPLETE
  80
  81 /* PXE */
  82 #define CONFIG_CMD_PXE
  83 #define CONFIG_MENU
  84
  85 #if defined(CONFIG_ZYNQ_SDHCI)
  86 # define CONFIG_MMC
  87 # define CONFIG_GENERIC_MMC
  88 # define CONFIG_SUPPORT_EMMC_BOOT
  89 # define CONFIG_SDHCI
  90 # ifndef CONFIG_ZYNQ_SDHCI_MAX_FREQ
  91 #  define CONFIG_ZYNQ_SDHCI_MAX_FREQ    200000000
  92 # endif
  93 #endif
  94
  95 #if defined(CONFIG_ZYNQ_SDHCI) || defined(CONFIG_ZYNQMP_USB)
  96 # define CONFIG_FAT_WRITE
  97 #endif
  98
  99 #ifdef CONFIG_NAND_ARASAN
 100 # define CONFIG_CMD_NAND_LOCK_UNLOCK
 101 # define CONFIG_SYS_MAX_NAND_DEVICE     1
 102 # define CONFIG_SYS_NAND_SELF_INIT
 103 # define CONFIG_SYS_NAND_ONFI_DETECTION
 104 # define CONFIG_MTD_DEVICE
 105 #endif
 106
 107 /* Miscellaneous configurable options */
 108 #define CONFIG_SYS_LOAD_ADDR            0x8000000
 109
 110 #if defined(CONFIG_ZYNQMP_USB)
 111 #define CONFIG_USB_MAX_CONTROLLER_COUNT         1
 112 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2
 113 #define CONFIG_USB_XHCI_ZYNQMP
 114
 115 #define CONFIG_SYS_DFU_DATA_BUF_SIZE    0x1800000
 116 #define DFU_DEFAULT_POLL_TIMEOUT        300
 117 #define CONFIG_USB_FUNCTION_DFU
 118 #define CONFIG_DFU_RAM
 119 #define CONFIG_USB_CABLE_CHECK
 120 #define CONFIG_CMD_THOR_DOWNLOAD
 121 #define CONFIG_USB_FUNCTION_THOR
 122 #define CONFIG_THOR_RESET_OFF
 123 #define DFU_ALT_INFO_RAM \
 124         "dfu_ram_info=" \
 125         "setenv dfu_alt_info " \
 126         "Image ram $kernel_addr $kernel_size\\\\;" \
 127         "system.dtb ram $fdt_addr $fdt_size\0" \
 128         "dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \
 129         "thor_ram=run dfu_ram_info && thordown 0 ram 0\0"
 130
 131 #define DFU_ALT_INFO  \
 132                 DFU_ALT_INFO_RAM
 133 #endif
 134
 135 #if !defined(DFU_ALT_INFO)
 136 # define DFU_ALT_INFO
 137 #endif
 138
 139
 140 #define CONFIG_BOARD_LATE_INIT
 141
 142 /* Do not preserve environment */
 143 #define CONFIG_ENV_IS_NOWHERE           1
 144 #define CONFIG_ENV_SIZE                 0x1000
 145
 146 /* Monitor Command Prompt */
 147 /* Console I/O Buffer Size */
 148 #define CONFIG_SYS_CBSIZE               2048
 149 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 150                                         sizeof(CONFIG_SYS_PROMPT) + 16)
 151 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 152 #define CONFIG_SYS_LONGHELP
 153 #define CONFIG_CMDLINE_EDITING
 154 #define CONFIG_SYS_MAXARGS              64
 155
 156 /* Ethernet driver */
 157 #if defined(CONFIG_ZYNQ_GEM)
 158 # define CONFIG_NET_MULTI
 159 # define CONFIG_MII
 160 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
 161 # define CONFIG_PHY_MARVELL
 162 # define CONFIG_PHY_NATSEMI
 163 # define CONFIG_PHY_TI
 164 # define CONFIG_PHY_GIGE
 165 # define CONFIG_PHY_VITESSE
 166 # define CONFIG_PHY_REALTEK
 167 # define PHY_ANEG_TIMEOUT       20000
 168 #endif
 169
 170 /* I2C */
 171 #if defined(CONFIG_SYS_I2C_ZYNQ)
 172 # define CONFIG_SYS_I2C
 173 # define CONFIG_SYS_I2C_ZYNQ_SPEED              100000
 174 # define CONFIG_SYS_I2C_ZYNQ_SLAVE              0
 175 #endif
 176
 177 /* EEPROM */
 178 #ifdef CONFIG_ZYNQMP_EEPROM
 179 # define CONFIG_CMD_EEPROM
 180 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         2
 181 # define CONFIG_SYS_I2C_EEPROM_ADDR             0x54
 182 # define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      4
 183 # define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  5
 184 # define CONFIG_SYS_EEPROM_SIZE                 (64 * 1024)
 185 #endif
 186
 187 #ifdef CONFIG_SATA_CEVA
 188 #define CONFIG_AHCI
 189 #define CONFIG_LIBATA
 190 #define CONFIG_SCSI_AHCI
 191 #define CONFIG_SCSI_AHCI_PLAT
 192 #define CONFIG_SYS_SCSI_MAX_SCSI_ID     2
 193 #define CONFIG_SYS_SCSI_MAX_LUN         1
 194 #define CONFIG_SYS_SCSI_MAX_DEVICE      (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
 195                                          CONFIG_SYS_SCSI_MAX_LUN)
 196 #define CONFIG_SCSI
 197 #endif
 198
 199 #define CONFIG_SYS_BOOTM_LEN    (60 * 1024 * 1024)
 200
 201 #define CONFIG_CMD_UNZIP
 202
 203 #define CONFIG_BOARD_EARLY_INIT_R
 204 #define CONFIG_CLOCKS
 205
 206 #define ENV_MEM_LAYOUT_SETTINGS \
 207         "fdt_high=10000000\0" \
 208         "initrd_high=10000000\0" \
 209         "fdt_addr_r=0x40000000\0" \
 210         "pxefile_addr_r=0x10000000\0" \
 211         "kernel_addr_r=0x18000000\0" \
 212         "scriptaddr=0x02000000\0" \
 213         "ramdisk_addr_r=0x02100000\0" \
 214
 215 #if defined(CONFIG_ZYNQ_SDHCI)
 216 # define BOOT_TARGET_DEVICES_MMC(func)  func(MMC, mmc, 0) func(MMC, mmc, 1)
 217 #else
 218 # define BOOT_TARGET_DEVICES_MMC(func)
 219 #endif
 220
 221 #if defined(CONFIG_SATA_CEVA)
 222 # define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
 223 #else
 224 # define BOOT_TARGET_DEVICES_SCSI(func)
 225 #endif
 226
 227 #if defined(CONFIG_ZYNQMP_USB)
 228 # define BOOT_TARGET_DEVICES_USB(func)  func(USB, usb, 0) func(USB, usb, 1)
 229 #else
 230 # define BOOT_TARGET_DEVICES_USB(func)
 231 #endif
 232
 233 #define BOOT_TARGET_DEVICES(func) \
 234         BOOT_TARGET_DEVICES_MMC(func) \
 235         BOOT_TARGET_DEVICES_USB(func) \
 236         BOOT_TARGET_DEVICES_SCSI(func) \
 237         func(PXE, pxe, na) \
 238         func(DHCP, dhcp, na)
 239
 240 #include <config_distro_bootcmd.h>
 241
 242 /* Initial environment variables */
 243 #ifndef CONFIG_EXTRA_ENV_SETTINGS
 244 #define CONFIG_EXTRA_ENV_SETTINGS \
 245         ENV_MEM_LAYOUT_SETTINGS \
 246         BOOTENV \
 247         DFU_ALT_INFO
 248 #endif
 249
 250 #define CONFIG_SPL_TEXT_BASE            0xfffc0000
 251 #define CONFIG_SPL_STACK                0xfffffffc
 252 #define CONFIG_SPL_MAX_SIZE             0x20000
 253
 254 /* Just random location in OCM */
 255 #define CONFIG_SPL_BSS_START_ADDR       0x1000000
 256 #define CONFIG_SPL_BSS_MAX_SIZE         0x2000000
 257
 258 #define CONFIG_SPL_FRAMEWORK
 259 #define CONFIG_SPL_BOARD_INIT
 260 #define CONFIG_SPL_RAM_DEVICE
 261
 262 #define CONFIG_SPL_OS_BOOT
 263 /* u-boot is like dtb */
 264 #define CONFIG_SPL_FS_LOAD_ARGS_NAME    "u-boot.bin"
 265 #define CONFIG_SYS_SPL_ARGS_ADDR        0x8000000
 266
 267 /* ATF is my kernel image */
 268 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME  "atf.ub"
 269
 270 /* FIT load address for RAM boot */
 271 #define CONFIG_SPL_LOAD_FIT_ADDRESS     0x10000000
 272
 273 /* MMC support */
 274 #ifdef CONFIG_ZYNQ_SDHCI
 275 # define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
 276 # define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR  0 /* unused */
 277 # define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0 /* unused */
 278 # define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR        0 /* unused */
 279 # define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME        "u-boot.img"
 280 #endif
 281
 282 #endif /* __XILINX_ZYNQMP_H */