]> git.ipfire.org Git - people/ms/u-boot.git/blob - include/configs/xpedite517x.h
projects / people / ms / u-boot.git / blob
? search:
summary | shortlog | log | commit | commitdiff | tree
blame | history | raw | HEAD
Kconfig: Drop CONFIG_SYS_I2C_DS1621_ADDR
[people/ms/u-boot.git] / include / configs / xpedite517x.h
1 /*
2 * Copyright 2009 Extreme Engineering Solutions, Inc.
3 * Copyright 2007-2008 Freescale Semiconductor, Inc.
4 *
5 * SPDX-License-Identifier: GPL-2.0+
6 */
7
8 /*
9 * xpedite517x board configuration file
10 */
11 #ifndef __CONFIG_H
12 #define __CONFIG_H
13
14 /*
15 * High Level Configuration Options
16 */
17 #define CONFIG_XPEDITE5140 1 /* MPC8641HPCN board specific */
18 #define CONFIG_SYS_BOARD_NAME "XPedite5170"
19 #define CONFIG_SYS_FORM_3U_VPX 1
20 #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
21 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */
22 #define CONFIG_BAT_RW 1 /* Use common BAT rw code */
23 #define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */
24 #define CONFIG_ALTIVEC 1
25
26 #define CONFIG_SYS_TEXT_BASE 0xfff00000
27
28 #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
29 #define CONFIG_PCIE1 1 /* PCIE controller 1 */
30 #define CONFIG_PCIE2 1 /* PCIE controller 2 */
31 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
32 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
33 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
34
35 /*
36 * DDR config
37 */
38 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
39 #define CONFIG_DDR_SPD
40 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef
41 #define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */
42 #define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */
43 #define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */
44 #define CONFIG_DIMM_SLOTS_PER_CTLR 1
45 #define CONFIG_CHIP_SELECTS_PER_CTRL 1
46 #define CONFIG_DDR_ECC
47 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
48 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
49 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
50 #define CONFIG_VERY_BIG_RAM
51 #define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */
52
53 /*
54 * virtual address to be used for temporary mappings. There
55 * should be 128k free at this VA.
56 */
57 #define CONFIG_SYS_SCRATCH_VA 0xe0000000
58
59 #ifndef __ASSEMBLY__
60 extern unsigned long get_board_sys_clk(unsigned long dummy);
61 #endif
62
63 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC86xx */
64
65 /*
66 * L2CR setup
67 */
68 #define CONFIG_SYS_L2
69 #define L2_INIT 0
70 #define L2_ENABLE (L2CR_L2E)
71
72 /*
73 * Base addresses -- Note these are effective addresses where the
74 * actual resources get mapped (not physical addresses)
75 */
76 #define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */
77 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR
78 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
79 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0
80 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR
81
82 /*
83 * Diagnostics
84 */
85 #define CONFIG_SYS_ALT_MEMTEST
86 #define CONFIG_SYS_MEMTEST_START 0x10000000
87 #define CONFIG_SYS_MEMTEST_END 0x20000000
88 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY |\
89 CONFIG_SYS_POST_I2C)
90 /* The XPedite5170 can host an XMC which has an EEPROM at address 0x50 */
91 #define I2C_ADDR_IGNORE_LIST {0x50}
92
93 /*
94 * Memory map
95 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
96 * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable
97 * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable
98 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable
99 * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable
100 * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable
101 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable
102 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable
103 * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable
104 * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable
105 */
106
107 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_4 | LCRR_EADC_3)
108
109 /*
110 * NAND flash configuration
111 */
112 #define CONFIG_SYS_NAND_BASE 0xef800000
113 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */
114 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE2}
115 #define CONFIG_SYS_MAX_NAND_DEVICE 2
116 #define CONFIG_NAND_ACTL
117 #define CONFIG_SYS_NAND_ACTL_ALE (1 << 14) /* C_LA14 */
118 #define CONFIG_SYS_NAND_ACTL_CLE (1 << 15) /* C_LA15 */
119 #define CONFIG_SYS_NAND_ACTL_NCE 0 /* NCE not controlled by ADDR */
120 #define CONFIG_SYS_NAND_ACTL_DELAY 25
121 #define CONFIG_JFFS2_NAND
122
123 /*
124 * NOR flash configuration
125 */
126 #define CONFIG_SYS_FLASH_BASE 0xf8000000
127 #define CONFIG_SYS_FLASH_BASE2 0xf0000000
128 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
129 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
130 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
131 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
132 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
133 #define CONFIG_FLASH_CFI_DRIVER
134 #define CONFIG_SYS_FLASH_CFI
135 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
136 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff00000, 0xc0000}, \
137 {0xf7f00000, 0xc0000} }
138 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
139 #define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */
140
141 /*
142 * Chip select configuration
143 */
144 /* NOR Flash 0 on CS0 */
145 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE |\
146 BR_PS_16 |\
147 BR_V)
148 #define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB |\
149 OR_GPCM_CSNT |\
150 OR_GPCM_XACS |\
151 OR_GPCM_ACS_DIV2 |\
152 OR_GPCM_SCY_8 |\
153 OR_GPCM_TRLX |\
154 OR_GPCM_EHTR |\
155 OR_GPCM_EAD)
156
157 /* NOR Flash 1 on CS1 */
158 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 |\
159 BR_PS_16 |\
160 BR_V)
161 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
162
163 /* NAND flash on CS2 */
164 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE |\
165 BR_PS_8 |\
166 BR_V)
167 #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB |\
168 OR_GPCM_BCTLD |\
169 OR_GPCM_CSNT |\
170 OR_GPCM_ACS_DIV4 |\
171 OR_GPCM_SCY_4 |\
172 OR_GPCM_TRLX |\
173 OR_GPCM_EHTR)
174
175 /* Optional NAND flash on CS3 */
176 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 |\
177 BR_PS_8 |\
178 BR_V)
179 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
180
181 /*
182 * Use L1 as initial stack
183 */
184 #define CONFIG_SYS_INIT_RAM_LOCK 1
185 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000
186 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
187
188 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
189 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
190
191 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
192 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
193
194 /*
195 * Serial Port
196 */
197 #define CONFIG_CONS_INDEX 1
198 #define CONFIG_SYS_NS16550_SERIAL
199 #define CONFIG_SYS_NS16550_REG_SIZE 1
200 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
201 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
202 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
203 #define CONFIG_SYS_BAUDRATE_TABLE \
204 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
205 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
206 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
207
208 /*
209 * I2C
210 */
211 #define CONFIG_SYS_I2C
212 #define CONFIG_SYS_I2C_FSL
213 #define CONFIG_SYS_FSL_I2C_SPEED 100000
214 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
215 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
216 #define CONFIG_SYS_FSL_I2C2_SPEED 100000
217 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
218 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
219
220 /* PEX8518 slave I2C interface */
221 #define CONFIG_SYS_I2C_PEX8518_ADDR 0x70
222
223 /* I2C DS1631 temperature sensor */
224 #define CONFIG_SYS_I2C_LM90_ADDR 0x4c
225
226 /* I2C EEPROM - AT24C128B */
227 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
228 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
229 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
230 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
231
232 /* I2C RTC */
233 #define CONFIG_RTC_M41T11 1
234 #define CONFIG_SYS_I2C_RTC_ADDR 0x68
235 #define CONFIG_SYS_M41T11_BASE_YEAR 2000
236
237 /* GPIO/EEPROM/SRAM */
238 #define CONFIG_SYS_I2C_DS4510_ADDR 0x51
239
240 /* GPIO */
241 #define CONFIG_PCA953X
242 #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
243 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c
244 #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e
245 #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f
246 #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0
247 #define CONFIG_SYS_I2C_PCA9553_ADDR 0x62
248
249 /*
250 * PU = pulled high, PD = pulled low
251 * I = input, O = output, IO = input/output
252 */
253 /* PCA9557 @ 0x18*/
254 #define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */
255 #define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */
256 #define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */
257 #define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */
258 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */
259 #define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */
260
261 /* PCA9557 @ 0x1c*/
262 #define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */
263 #define CONFIG_SYS_PCA953X_PLUG_GPIO0 0x02 /* Samtec connector GPIO */
264 #define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */
265 #define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */
266 #define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */
267 #define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */
268 #define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */
269 #define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */
270
271 /* PCA9557 @ 0x1e*/
272 #define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */
273 #define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */
274 #define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */
275 #define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */
276 #define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */
277 #define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; VPX Geographical address parity */
278 #define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; VPX P1 SYSCON */
279
280 /* PCA9557 @ 0x1f */
281 #define CONFIG_SYS_PCA953X_VPX_GPIO0 0x01 /* PU; VPX P15 GPIO */
282 #define CONFIG_SYS_PCA953X_VPX_GPIO1 0x02 /* PU; VPX P15 GPIO */
283 #define CONFIG_SYS_PCA953X_VPX_GPIO2 0x04 /* PU; VPX P15 GPIO */
284 #define CONFIG_SYS_PCA953X_VPX_GPIO3 0x08 /* PU; VPX P15 GPIO */
285
286 /*
287 * General PCI
288 * Memory space is mapped 1-1, but I/O space must start from 0.
289 */
290 /* PCIE1 - PEX8518 */
291 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
292 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS
293 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */
294 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
295 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000
296 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
297
298 /* PCIE2 - VPX P1 */
299 #define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000
300 #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS
301 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
302 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
303 #define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000
304 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */
305
306 /*
307 * Networking options
308 */
309 #define CONFIG_TSEC_ENET /* tsec ethernet support */
310 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
311 #define CONFIG_MII 1 /* MII PHY management */
312 #define CONFIG_ETHPRIME "eTSEC1"
313
314 #define CONFIG_TSEC1 1
315 #define CONFIG_TSEC1_NAME "eTSEC1"
316 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
317 #define TSEC1_PHY_ADDR 1
318 #define TSEC1_PHYIDX 0
319 #define CONFIG_HAS_ETH0
320
321 #define CONFIG_TSEC2 1
322 #define CONFIG_TSEC2_NAME "eTSEC2"
323 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
324 #define TSEC2_PHY_ADDR 2
325 #define TSEC2_PHYIDX 0
326 #define CONFIG_HAS_ETH1
327
328 /*
329 * BAT mappings
330 */
331 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
332 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT |\
333 BATL_PP_RW |\
334 BATL_CACHEINHIBIT |\
335 BATL_GUARDEDSTORAGE)
336 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT |\
337 BATU_BL_1M |\
338 BATU_VS |\
339 BATU_VP)
340 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT |\
341 BATL_PP_RW |\
342 BATL_CACHEINHIBIT)
343 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
344 #endif
345
346 /*
347 * BAT0 2G Cacheable, non-guarded
348 * 0x0000_0000 2G DDR
349 */
350 #define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
351 #define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
352 #define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
353 #define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U
354
355 /*
356 * BAT1 1G Cache-inhibited, guarded
357 * 0x8000_0000 1G PCI-Express 1 Memory
358 */
359 #define CONFIG_SYS_DBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS |\
360 BATL_PP_RW |\
361 BATL_CACHEINHIBIT |\
362 BATL_GUARDEDSTORAGE)
363 #define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCIE1_MEM_PHYS |\
364 BATU_BL_1G |\
365 BATU_VS |\
366 BATU_VP)
367 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS |\
368 BATL_PP_RW |\
369 BATL_CACHEINHIBIT)
370 #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U
371
372 /*
373 * BAT2 512M Cache-inhibited, guarded
374 * 0xc000_0000 512M PCI-Express 2 Memory
375 */
376 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCIE2_MEM_PHYS |\
377 BATL_PP_RW |\
378 BATL_CACHEINHIBIT |\
379 BATL_GUARDEDSTORAGE)
380 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE2_MEM_PHYS |\
381 BATU_BL_512M |\
382 BATU_VS |\
383 BATU_VP)
384 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCIE2_MEM_PHYS |\
385 BATL_PP_RW |\
386 BATL_CACHEINHIBIT)
387 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U
388
389 /*
390 * BAT3 1M Cache-inhibited, guarded
391 * 0xe000_0000 1M CCSR
392 */
393 #define CONFIG_SYS_DBAT3L (CONFIG_SYS_CCSRBAR |\
394 BATL_PP_RW |\
395 BATL_CACHEINHIBIT |\
396 BATL_GUARDEDSTORAGE)
397 #define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR |\
398 BATU_BL_1M |\
399 BATU_VS |\
400 BATU_VP)
401 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR |\
402 BATL_PP_RW |\
403 BATL_CACHEINHIBIT)
404 #define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U
405
406 /*
407 * BAT4 32M Cache-inhibited, guarded
408 * 0xe200_0000 16M PCI-Express 1 I/O
409 * 0xe300_0000 16M PCI-Express 2 I/0
410 */
411 #define CONFIG_SYS_DBAT4L (CONFIG_SYS_PCIE1_IO_PHYS |\
412 BATL_PP_RW |\
413 BATL_CACHEINHIBIT |\
414 BATL_GUARDEDSTORAGE)
415 #define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_PHYS |\
416 BATU_BL_32M |\
417 BATU_VS |\
418 BATU_VP)
419 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE1_IO_PHYS |\
420 BATL_PP_RW |\
421 BATL_CACHEINHIBIT)
422 #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U
423
424 /*
425 * BAT5 128K Cacheable, non-guarded
426 * 0xe400_1000 128K Init RAM for stack in the CPU DCache (no backing memory)
427 */
428 #define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR |\
429 BATL_PP_RW |\
430 BATL_MEMCOHERENCE)
431 #define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR |\
432 BATU_BL_128K |\
433 BATU_VS |\
434 BATU_VP)
435 #define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L
436 #define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U
437
438 /*
439 * BAT6 256M Cache-inhibited, guarded
440 * 0xf000_0000 256M FLASH
441 */
442 #define CONFIG_SYS_DBAT6L (CONFIG_SYS_FLASH_BASE2 |\
443 BATL_PP_RW |\
444 BATL_CACHEINHIBIT |\
445 BATL_GUARDEDSTORAGE)
446 #define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE |\
447 BATU_BL_256M |\
448 BATU_VS |\
449 BATU_VP)
450 #define CONFIG_SYS_IBAT6L (CONFIG_SYS_FLASH_BASE |\
451 BATL_PP_RW |\
452 BATL_MEMCOHERENCE)
453 #define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U
454
455 /* Map the last 1M of flash where we're running from reset */
456 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY |\
457 BATL_PP_RW |\
458 BATL_CACHEINHIBIT |\
459 BATL_GUARDEDSTORAGE)
460 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE |\
461 BATU_BL_1M |\
462 BATU_VS |\
463 BATU_VP)
464 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY |\
465 BATL_PP_RW |\
466 BATL_MEMCOHERENCE)
467 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
468
469 /*
470 * BAT7 64M Cache-inhibited, guarded
471 * 0xe800_0000 64K NAND FLASH
472 * 0xe804_0000 128K DUART Registers
473 */
474 #define CONFIG_SYS_DBAT7L (CONFIG_SYS_NAND_BASE |\
475 BATL_PP_RW |\
476 BATL_CACHEINHIBIT |\
477 BATL_GUARDEDSTORAGE)
478 #define CONFIG_SYS_DBAT7U (CONFIG_SYS_NAND_BASE |\
479 BATU_BL_512K |\
480 BATU_VS |\
481 BATU_VP)
482 #define CONFIG_SYS_IBAT7L (CONFIG_SYS_NAND_BASE |\
483 BATL_PP_RW |\
484 BATL_CACHEINHIBIT)
485 #define CONFIG_SYS_IBAT7U CONFIG_SYS_DBAT7U
486
487 /*
488 * Command configuration.
489 */
490 #define CONFIG_CMD_EEPROM
491 #define CONFIG_CMD_IRQ
492 #define CONFIG_CMD_JFFS2
493 #define CONFIG_CMD_NAND
494 #define CONFIG_CMD_PCA953X
495 #define CONFIG_CMD_PCA953X_INFO
496 #define CONFIG_CMD_PCI
497 #define CONFIG_CMD_PCI_ENUM
498 #define CONFIG_CMD_REGINFO
499
500 /*
501 * Miscellaneous configurable options
502 */
503 #define CONFIG_SYS_LONGHELP /* undef to save memory */
504 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
505 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
506 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
507 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */
508 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
509 #define CONFIG_CMDLINE_EDITING 1 /* Command-line editing */
510 #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
511 #define CONFIG_PANIC_HANG /* do not reset board on panic */
512 #define CONFIG_PREBOOT /* enable preboot variable */
513 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
514
515 /*
516 * For booting Linux, the board info and command line data
517 * have to be in the first 16 MB of memory, since this is
518 * the maximum mapped by the Linux kernel during initialization.
519 */
520 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
521 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
522
523 /*
524 * Environment Configuration
525 */
526 #define CONFIG_ENV_IS_IN_FLASH 1
527 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */
528 #define CONFIG_ENV_SIZE 0x8000
529 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
530
531 /*
532 * Flash memory map:
533 * fffc0000 - ffffffff Pri FDT (256KB)
534 * fff80000 - fffbffff Pri U-Boot Environment (256 KB)
535 * fff00000 - fff7ffff Pri U-Boot (512 KB)
536 * fef00000 - ffefffff Pri OS image (16MB)
537 * f8000000 - feefffff Pri OS Use/Filesystem (111MB)
538 *
539 * f7fc0000 - f7ffffff Sec FDT (256KB)
540 * f7f80000 - f7fbffff Sec U-Boot Environment (256 KB)
541 * f7f00000 - f7f7ffff Sec U-Boot (512 KB)
542 * f6f00000 - f7efffff Sec OS image (16MB)
543 * f0000000 - f6efffff Sec OS Use/Filesystem (111MB)
544 */
545 #define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff00000)
546 #define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f00000)
547 #define CONFIG_FDT1_ENV_ADDR __stringify(0xfffc0000)
548 #define CONFIG_FDT2_ENV_ADDR __stringify(0xf7fc0000)
549 #define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000)
550 #define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000)
551
552 #define CONFIG_PROG_UBOOT1 \
553 "$download_cmd $loadaddr $ubootfile; " \
554 "if test $? -eq 0; then " \
555 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
556 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
557 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \
558 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
559 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \
560 "if test $? -ne 0; then " \
561 "echo PROGRAM FAILED; " \
562 "else; " \
563 "echo PROGRAM SUCCEEDED; " \
564 "fi; " \
565 "else; " \
566 "echo DOWNLOAD FAILED; " \
567 "fi;"
568
569 #define CONFIG_PROG_UBOOT2 \
570 "$download_cmd $loadaddr $ubootfile; " \
571 "if test $? -eq 0; then " \
572 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
573 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
574 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \
575 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
576 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \
577 "if test $? -ne 0; then " \
578 "echo PROGRAM FAILED; " \
579 "else; " \
580 "echo PROGRAM SUCCEEDED; " \
581 "fi; " \
582 "else; " \
583 "echo DOWNLOAD FAILED; " \
584 "fi;"
585
586 #define CONFIG_BOOT_OS_NET \
587 "$download_cmd $osaddr $osfile; " \
588 "if test $? -eq 0; then " \
589 "if test -n $fdtaddr; then " \
590 "$download_cmd $fdtaddr $fdtfile; " \
591 "if test $? -eq 0; then " \
592 "bootm $osaddr - $fdtaddr; " \
593 "else; " \
594 "echo FDT DOWNLOAD FAILED; " \
595 "fi; " \
596 "else; " \
597 "bootm $osaddr; " \
598 "fi; " \
599 "else; " \
600 "echo OS DOWNLOAD FAILED; " \
601 "fi;"
602
603 #define CONFIG_PROG_OS1 \
604 "$download_cmd $osaddr $osfile; " \
605 "if test $? -eq 0; then " \
606 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \
607 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
608 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
609 "if test $? -ne 0; then " \
610 "echo OS PROGRAM FAILED; " \
611 "else; " \
612 "echo OS PROGRAM SUCCEEDED; " \
613 "fi; " \
614 "else; " \
615 "echo OS DOWNLOAD FAILED; " \
616 "fi;"
617
618 #define CONFIG_PROG_OS2 \
619 "$download_cmd $osaddr $osfile; " \
620 "if test $? -eq 0; then " \
621 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \
622 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
623 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
624 "if test $? -ne 0; then " \
625 "echo OS PROGRAM FAILED; " \
626 "else; " \
627 "echo OS PROGRAM SUCCEEDED; " \
628 "fi; " \
629 "else; " \
630 "echo OS DOWNLOAD FAILED; " \
631 "fi;"
632
633 #define CONFIG_PROG_FDT1 \
634 "$download_cmd $fdtaddr $fdtfile; " \
635 "if test $? -eq 0; then " \
636 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \
637 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
638 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
639 "if test $? -ne 0; then " \
640 "echo FDT PROGRAM FAILED; " \
641 "else; " \
642 "echo FDT PROGRAM SUCCEEDED; " \
643 "fi; " \
644 "else; " \
645 "echo FDT DOWNLOAD FAILED; " \
646 "fi;"
647
648 #define CONFIG_PROG_FDT2 \
649 "$download_cmd $fdtaddr $fdtfile; " \
650 "if test $? -eq 0; then " \
651 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \
652 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
653 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
654 "if test $? -ne 0; then " \
655 "echo FDT PROGRAM FAILED; " \
656 "else; " \
657 "echo FDT PROGRAM SUCCEEDED; " \
658 "fi; " \
659 "else; " \
660 "echo FDT DOWNLOAD FAILED; " \
661 "fi;"
662
663 #define CONFIG_EXTRA_ENV_SETTINGS \
664 "autoload=yes\0" \
665 "download_cmd=tftp\0" \
666 "console_args=console=ttyS0,115200\0" \
667 "root_args=root=/dev/nfs rw\0" \
668 "misc_args=ip=on\0" \
669 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
670 "bootfile=/home/user/file\0" \
671 "osfile=/home/user/board.uImage\0" \
672 "fdtfile=/home/user/board.dtb\0" \
673 "ubootfile=/home/user/u-boot.bin\0" \
674 "fdtaddr=0x1e00000\0" \
675 "osaddr=0x1000000\0" \
676 "loadaddr=0x1000000\0" \
677 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \
678 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \
679 "prog_os1="CONFIG_PROG_OS1"\0" \
680 "prog_os2="CONFIG_PROG_OS2"\0" \
681 "prog_fdt1="CONFIG_PROG_FDT1"\0" \
682 "prog_fdt2="CONFIG_PROG_FDT2"\0" \
683 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
684 "bootcmd_flash1=run set_bootargs; " \
685 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
686 "bootcmd_flash2=run set_bootargs; " \
687 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
688 "bootcmd=run bootcmd_flash1\0"
689 #endif /* __CONFIG_H */
"Das U-Boot" Source Tree