include/configs/xtfpga.h

   1 /*
   2  * Copyright (C) 2007-2013 Tensilica, Inc.
   3  * Copyright (C) 2014 - 2016 Cadence Design Systems Inc.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #ifndef __CONFIG_H
   9 #define __CONFIG_H
  10
  11 #include <asm/arch/core.h>
  12 #include <asm/addrspace.h>
  13 #include <asm/config.h>
  14
  15 /*
  16  * The 'xtfpga' board describes a set of very similar boards with only minimal
  17  * differences.
  18  */
  19
  20 /*=====================*/
  21 /* Board and Processor */
  22 /*=====================*/
  23
  24 #define CONFIG_XTFPGA
  25
  26 /* FPGA CPU freq after init */
  27 #define CONFIG_SYS_CLK_FREQ             (gd->cpu_clk)
  28
  29 /*===================*/
  30 /* RAM Layout        */
  31 /*===================*/
  32
  33 #if XCHAL_HAVE_PTP_MMU
  34 #define CONFIG_SYS_MEMORY_BASE          \
  35         (XCHAL_VECBASE_RESET_VADDR - XCHAL_VECBASE_RESET_PADDR)
  36 #define CONFIG_SYS_IO_BASE              0xf0000000
  37 #else
  38 #define CONFIG_SYS_MEMORY_BASE          0x60000000
  39 #define CONFIG_SYS_IO_BASE              0x90000000
  40 #define CONFIG_MAX_MEM_MAPPED           0x10000000
  41 #endif
  42
  43 /* Onboard RAM sizes:
  44  *
  45  * LX60         0x04000000                64 MB
  46  * LX110        0x03000000                48 MB
  47  * LX200        0x06000000                96 MB
  48  * ML605        0x18000000               384 MB
  49  * KC705        0x38000000               896 MB
  50  *
  51  * noMMU configurations can only see first 256MB of onboard memory.
  52  */
  53
  54 #if XCHAL_HAVE_PTP_MMU || CONFIG_BOARD_SDRAM_SIZE < 0x10000000
  55 #define CONFIG_SYS_SDRAM_SIZE           CONFIG_BOARD_SDRAM_SIZE
  56 #else
  57 #define CONFIG_SYS_SDRAM_SIZE           0x10000000
  58 #endif
  59
  60 #define CONFIG_SYS_SDRAM_BASE           MEMADDR(0x00000000)
  61
  62 /* Lx60 can only map 128kb memory (instead of 256kb) when running under OCD */
  63 #ifdef CONFIG_XTFPGA_LX60
  64 # define CONFIG_SYS_MONITOR_LEN         0x00020000      /* 128KB */
  65 #else
  66 # define CONFIG_SYS_MONITOR_LEN         0x00040000      /* 256KB */
  67 #endif
  68
  69 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)     /* heap  256KB */
  70
  71 /* Linux boot param area in RAM (used only when booting linux) */
  72 #define CONFIG_SYS_BOOTPARAMS_LEN       (64  << 10)
  73
  74 /* Memory test is destructive so default must not overlap vectors or U-Boot*/
  75 #define CONFIG_SYS_MEMTEST_START        MEMADDR(0x01000000)
  76 #define CONFIG_SYS_MEMTEST_END          MEMADDR(0x02000000)
  77
  78 /* Load address for stand-alone applications.
  79  * MEMADDR cannot be used here, because the definition needs to be
  80  * a plain number as it's used as -Ttext argument for ld in standalone
  81  * example makefile.
  82  * Handle noMMU vs MMUv2 vs MMUv3 distinction here manually.
  83  */
  84 #if XCHAL_HAVE_PTP_MMU
  85 #if XCHAL_VECBASE_RESET_VADDR == XCHAL_VECBASE_RESET_PADDR
  86 #define CONFIG_STANDALONE_LOAD_ADDR     0x00800000
  87 #else
  88 #define CONFIG_STANDALONE_LOAD_ADDR     0xd0800000
  89 #endif
  90 #else
  91 #define CONFIG_STANDALONE_LOAD_ADDR     0x60800000
  92 #endif
  93
  94 #if defined(CONFIG_MAX_MEM_MAPPED) && \
  95         CONFIG_MAX_MEM_MAPPED < CONFIG_SYS_SDRAM_SIZE
  96 #define CONFIG_SYS_MEMORY_SIZE          CONFIG_MAX_MEM_MAPPED
  97 #else
  98 #define CONFIG_SYS_MEMORY_SIZE          CONFIG_SYS_SDRAM_SIZE
  99 #endif
 100
 101 #define CONFIG_SYS_MEMORY_TOP           MEMADDR(CONFIG_SYS_MEMORY_SIZE)
 102 #define CONFIG_SYS_TEXT_ADDR            \
 103         (CONFIG_SYS_MEMORY_TOP - CONFIG_SYS_MONITOR_LEN)
 104
 105 /* Used by tftpboot; env var 'loadaddr' */
 106 #define CONFIG_SYS_LOAD_ADDR            MEMADDR(0x02000000)
 107
 108 /*==============================*/
 109 /* U-Boot general configuration */
 110 /*==============================*/
 111
 112 #define CONFIG_BOARD_POSTCLK_INIT
 113 #define CONFIG_MISC_INIT_R
 114
 115 #define CONFIG_BOOTFILE                 "uImage"
 116         /* Console I/O Buffer Size  */
 117 #define CONFIG_SYS_CBSIZE               1024
 118         /* Boot Argument Buffer Size */
 119 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 120
 121 /*==============================*/
 122 /* U-Boot autoboot configuration */
 123 /*==============================*/
 124
 125 #define CONFIG_AUTO_COMPLETE                    /* Support tab autocompletion */
 126 #define CONFIG_CMDLINE_EDITING
 127 #define CONFIG_SYS_LONGHELP
 128 #define CONFIG_MX_CYCLIC
 129 #define CONFIG_SHOW_BOOT_PROGRESS
 130
 131
 132 /*=========================================*/
 133 /* FPGA Registers (board info and control) */
 134 /*=========================================*/
 135
 136 /*
 137  * These assume FPGA bitstreams from Tensilica release RB and up. Earlier
 138  * releases may not provide any/all of these registers or at these offsets.
 139  * Some of the FPGA registers are broken down into bitfields described by
 140  * SHIFT left amount and field WIDTH (bits), and also by a bitMASK.
 141  */
 142
 143 /* Date of FPGA bitstream build in binary coded decimal (BCD) */
 144 #define CONFIG_SYS_FPGAREG_DATE         IOADDR(0x0D020000)
 145 #define FPGAREG_MTH_SHIFT               24              /* BCD month 1..12 */
 146 #define FPGAREG_MTH_WIDTH               8
 147 #define FPGAREG_MTH_MASK                0xFF000000
 148 #define FPGAREG_DAY_SHIFT               16              /* BCD day 1..31 */
 149 #define FPGAREG_DAY_WIDTH               8
 150 #define FPGAREG_DAY_MASK                0x00FF0000
 151 #define FPGAREG_YEAR_SHIFT              0               /* BCD year 2001..9999*/
 152 #define FPGAREG_YEAR_WIDTH              16
 153 #define FPGAREG_YEAR_MASK               0x0000FFFF
 154
 155 /* FPGA core clock frequency in Hz (also input to UART) */
 156 #define CONFIG_SYS_FPGAREG_FREQ IOADDR(0x0D020004)      /* CPU clock frequency*/
 157
 158 /*
 159  * DIP switch (left=sw1=lsb=bit0, right=sw8=msb=bit7; off=0, on=1):
 160  *   Bits 0..5 set the lower 6 bits of the default ethernet MAC.
 161  *   Bit 6 is reserved for future use by Tensilica.
 162  *   Bit 7 maps the first 128KB of ROM address space at CONFIG_SYS_ROM_BASE to
 163  *   the base of flash * (when on/1) or to the base of RAM (when off/0).
 164  */
 165 #define CONFIG_SYS_FPGAREG_DIPSW        IOADDR(0x0D02000C)
 166 #define FPGAREG_MAC_SHIFT               0       /* Ethernet MAC bits 0..5 */
 167 #define FPGAREG_MAC_WIDTH               6
 168 #define FPGAREG_MAC_MASK                0x3f
 169 #define FPGAREG_BOOT_SHIFT              7       /* Boot ROM addr mapping */
 170 #define FPGAREG_BOOT_WIDTH              1
 171 #define FPGAREG_BOOT_MASK               0x80
 172 #define FPGAREG_BOOT_RAM                0
 173 #define FPGAREG_BOOT_FLASH              (1<<FPGAREG_BOOT_SHIFT)
 174
 175 /* Force hard reset of board by writing a code to this register */
 176 #define CONFIG_SYS_FPGAREG_RESET        IOADDR(0x0D020010) /* Reset board .. */
 177 #define CONFIG_SYS_FPGAREG_RESET_CODE   0x0000DEAD   /*  by writing this code */
 178
 179 /*====================*/
 180 /* Serial Driver Info */
 181 /*====================*/
 182
 183 #define CONFIG_SYS_NS16550_SERIAL
 184 #define CONFIG_SYS_NS16550_REG_SIZE     (-4)
 185 #define CONFIG_SYS_NS16550_COM1         IOADDR(0x0D050020) /* Base address */
 186
 187 /* Input clk to NS16550 (in Hz; the SYS_CLK_FREQ is in kHz) */
 188 #define CONFIG_SYS_NS16550_CLK          CONFIG_SYS_CLK_FREQ
 189 #define CONFIG_CONS_INDEX               1       /* use UART0 for console */
 190 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
 191
 192 /*======================*/
 193 /* Ethernet Driver Info */
 194 /*======================*/
 195
 196 #define CONFIG_ETHBASE                  00:50:C2:13:6f:00
 197 #define CONFIG_SYS_ETHOC_BASE           IOADDR(0x0d030000)
 198 #define CONFIG_SYS_ETHOC_BUFFER_ADDR    IOADDR(0x0D800000)
 199
 200 /*=====================*/
 201 /* Flash & Environment */
 202 /*=====================*/
 203
 204 #define CONFIG_SYS_FLASH_CFI
 205 #define CONFIG_FLASH_CFI_DRIVER                 /* use generic CFI driver */
 206 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
 207 #define CONFIG_SYS_MAX_FLASH_BANKS      1
 208 #ifdef CONFIG_XTFPGA_LX60
 209 # define CONFIG_SYS_FLASH_SIZE          0x0040000       /* 4MB */
 210 # define CONFIG_SYS_FLASH_SECT_SZ       0x10000         /* block size 64KB */
 211 # define CONFIG_SYS_FLASH_PARMSECT_SZ   0x2000          /* param size  8KB */
 212 # define CONFIG_SYS_FLASH_BASE          IOADDR(0x08000000)
 213 # define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_FLASH_BASE
 214 #elif defined(CONFIG_XTFPGA_KC705)
 215 # define CONFIG_SYS_FLASH_SIZE          0x8000000       /* 128MB */
 216 # define CONFIG_SYS_FLASH_SECT_SZ       0x20000         /* block size 128KB */
 217 # define CONFIG_SYS_FLASH_PARMSECT_SZ   0x8000          /* param size 32KB */
 218 # define CONFIG_SYS_FLASH_BASE          IOADDR(0x00000000)
 219 # define CONFIG_SYS_MONITOR_BASE        IOADDR(0x06000000)
 220 #else
 221 # define CONFIG_SYS_FLASH_SIZE          0x1000000       /* 16MB */
 222 # define CONFIG_SYS_FLASH_SECT_SZ       0x20000         /* block size 128KB */
 223 # define CONFIG_SYS_FLASH_PARMSECT_SZ   0x8000          /* param size 32KB */
 224 # define CONFIG_SYS_FLASH_BASE          IOADDR(0x08000000)
 225 # define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_FLASH_BASE
 226 #endif
 227 #define CONFIG_SYS_MAX_FLASH_SECT       \
 228         (CONFIG_SYS_FLASH_SECT_SZ/CONFIG_SYS_FLASH_PARMSECT_SZ + \
 229          CONFIG_SYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ - 1)
 230 #define CONFIG_SYS_FLASH_PROTECTION             /* hw flash protection */
 231
 232 /*
 233  * Put environment in top block (64kB)
 234  * Another option would be to put env. in 2nd param block offs 8KB, size 8KB
 235  */
 236 #define CONFIG_ENV_OFFSET    (CONFIG_SYS_FLASH_SIZE - CONFIG_SYS_FLASH_SECT_SZ)
 237 #define CONFIG_ENV_SIZE      CONFIG_SYS_FLASH_SECT_SZ
 238
 239 /* print 'E' for empty sector on flinfo */
 240 #define CONFIG_SYS_FLASH_EMPTY_INFO
 241
 242 #endif /* __CONFIG_H */