]> git.ipfire.org Git - people/ms/u-boot.git/blob - include/net.h
arc/cache: really do invalidate_dcache_all() even if IOC exists
[people/ms/u-boot.git] / include / net.h
1 /*
2 * LiMon Monitor (LiMon) - Network.
3 *
4 * Copyright 1994 - 2000 Neil Russell.
5 * (See License)
6 * SPDX-License-Identifier: GPL-2.0
7 *
8 * History
9 * 9/16/00 bor adapted to TQM823L/STK8xxL board, RARP/TFTP boot added
10 */
11
12 #ifndef __NET_H__
13 #define __NET_H__
14
15 #if defined(CONFIG_8xx)
16 #include <commproc.h>
17 #endif /* CONFIG_8xx */
18
19 #include <asm/cache.h>
20 #include <asm/byteorder.h> /* for nton* / ntoh* stuff */
21
22 #define DEBUG_LL_STATE 0 /* Link local state machine changes */
23 #define DEBUG_DEV_PKT 0 /* Packets or info directed to the device */
24 #define DEBUG_NET_PKT 0 /* Packets on info on the network at large */
25 #define DEBUG_INT_STATE 0 /* Internal network state changes */
26
27 /*
28 * The number of receive packet buffers, and the required packet buffer
29 * alignment in memory.
30 *
31 */
32
33 #ifdef CONFIG_SYS_RX_ETH_BUFFER
34 # define PKTBUFSRX CONFIG_SYS_RX_ETH_BUFFER
35 #else
36 # define PKTBUFSRX 4
37 #endif
38
39 #define PKTALIGN ARCH_DMA_MINALIGN
40
41 /* IPv4 addresses are always 32 bits in size */
42 struct in_addr {
43 __be32 s_addr;
44 };
45
46 /**
47 * An incoming packet handler.
48 * @param pkt pointer to the application packet
49 * @param dport destination UDP port
50 * @param sip source IP address
51 * @param sport source UDP port
52 * @param len packet length
53 */
54 typedef void rxhand_f(uchar *pkt, unsigned dport,
55 struct in_addr sip, unsigned sport,
56 unsigned len);
57
58 /**
59 * An incoming ICMP packet handler.
60 * @param type ICMP type
61 * @param code ICMP code
62 * @param dport destination UDP port
63 * @param sip source IP address
64 * @param sport source UDP port
65 * @param pkt pointer to the ICMP packet data
66 * @param len packet length
67 */
68 typedef void rxhand_icmp_f(unsigned type, unsigned code, unsigned dport,
69 struct in_addr sip, unsigned sport, uchar *pkt, unsigned len);
70
71 /*
72 * A timeout handler. Called after time interval has expired.
73 */
74 typedef void thand_f(void);
75
76 enum eth_state_t {
77 ETH_STATE_INIT,
78 ETH_STATE_PASSIVE,
79 ETH_STATE_ACTIVE
80 };
81
82 #ifdef CONFIG_DM_ETH
83 /**
84 * struct eth_pdata - Platform data for Ethernet MAC controllers
85 *
86 * @iobase: The base address of the hardware registers
87 * @enetaddr: The Ethernet MAC address that is loaded from EEPROM or env
88 * @phy_interface: PHY interface to use - see PHY_INTERFACE_MODE_...
89 * @max_speed: Maximum speed of Ethernet connection supported by MAC
90 */
91 struct eth_pdata {
92 phys_addr_t iobase;
93 unsigned char enetaddr[6];
94 int phy_interface;
95 int max_speed;
96 };
97
98 enum eth_recv_flags {
99 /*
100 * Check hardware device for new packets (otherwise only return those
101 * which are already in the memory buffer ready to process)
102 */
103 ETH_RECV_CHECK_DEVICE = 1 << 0,
104 };
105
106 /**
107 * struct eth_ops - functions of Ethernet MAC controllers
108 *
109 * start: Prepare the hardware to send and receive packets
110 * send: Send the bytes passed in "packet" as a packet on the wire
111 * recv: Check if the hardware received a packet. If so, set the pointer to the
112 * packet buffer in the packetp parameter. If not, return an error or 0 to
113 * indicate that the hardware receive FIFO is empty. If 0 is returned, the
114 * network stack will not process the empty packet, but free_pkt() will be
115 * called if supplied
116 * free_pkt: Give the driver an opportunity to manage its packet buffer memory
117 * when the network stack is finished processing it. This will only be
118 * called when no error was returned from recv - optional
119 * stop: Stop the hardware from looking for packets - may be called even if
120 * state == PASSIVE
121 * mcast: Join or leave a multicast group (for TFTP) - optional
122 * write_hwaddr: Write a MAC address to the hardware (used to pass it to Linux
123 * on some platforms like ARM). This function expects the
124 * eth_pdata::enetaddr field to be populated. The method can
125 * return -ENOSYS to indicate that this is not implemented for
126 this hardware - optional.
127 * read_rom_hwaddr: Some devices have a backup of the MAC address stored in a
128 * ROM on the board. This is how the driver should expose it
129 * to the network stack. This function should fill in the
130 * eth_pdata::enetaddr field - optional
131 */
132 struct eth_ops {
133 int (*start)(struct udevice *dev);
134 int (*send)(struct udevice *dev, void *packet, int length);
135 int (*recv)(struct udevice *dev, int flags, uchar **packetp);
136 int (*free_pkt)(struct udevice *dev, uchar *packet, int length);
137 void (*stop)(struct udevice *dev);
138 #ifdef CONFIG_MCAST_TFTP
139 int (*mcast)(struct udevice *dev, const u8 *enetaddr, int join);
140 #endif
141 int (*write_hwaddr)(struct udevice *dev);
142 int (*read_rom_hwaddr)(struct udevice *dev);
143 };
144
145 #define eth_get_ops(dev) ((struct eth_ops *)(dev)->driver->ops)
146
147 struct udevice *eth_get_dev(void); /* get the current device */
148 /*
149 * The devname can be either an exact name given by the driver or device tree
150 * or it can be an alias of the form "eth%d"
151 */
152 struct udevice *eth_get_dev_by_name(const char *devname);
153 unsigned char *eth_get_ethaddr(void); /* get the current device MAC */
154
155 /* Used only when NetConsole is enabled */
156 int eth_is_active(struct udevice *dev); /* Test device for active state */
157 int eth_init_state_only(void); /* Set active state */
158 void eth_halt_state_only(void); /* Set passive state */
159 #endif
160
161 #ifndef CONFIG_DM_ETH
162 struct eth_device {
163 char name[16];
164 unsigned char enetaddr[6];
165 phys_addr_t iobase;
166 int state;
167
168 int (*init)(struct eth_device *, bd_t *);
169 int (*send)(struct eth_device *, void *packet, int length);
170 int (*recv)(struct eth_device *);
171 void (*halt)(struct eth_device *);
172 #ifdef CONFIG_MCAST_TFTP
173 int (*mcast)(struct eth_device *, const u8 *enetaddr, u8 set);
174 #endif
175 int (*write_hwaddr)(struct eth_device *);
176 struct eth_device *next;
177 int index;
178 void *priv;
179 };
180
181 int eth_register(struct eth_device *dev);/* Register network device */
182 int eth_unregister(struct eth_device *dev);/* Remove network device */
183
184 extern struct eth_device *eth_current;
185
186 static __always_inline struct eth_device *eth_get_dev(void)
187 {
188 return eth_current;
189 }
190 struct eth_device *eth_get_dev_by_name(const char *devname);
191 struct eth_device *eth_get_dev_by_index(int index); /* get dev @ index */
192
193 /* get the current device MAC */
194 static inline unsigned char *eth_get_ethaddr(void)
195 {
196 if (eth_current)
197 return eth_current->enetaddr;
198 return NULL;
199 }
200
201 /* Used only when NetConsole is enabled */
202 int eth_is_active(struct eth_device *dev); /* Test device for active state */
203 /* Set active state */
204 static __always_inline int eth_init_state_only(void)
205 {
206 eth_get_dev()->state = ETH_STATE_ACTIVE;
207
208 return 0;
209 }
210 /* Set passive state */
211 static __always_inline void eth_halt_state_only(void)
212 {
213 eth_get_dev()->state = ETH_STATE_PASSIVE;
214 }
215
216 /*
217 * Set the hardware address for an ethernet interface based on 'eth%daddr'
218 * environment variable (or just 'ethaddr' if eth_number is 0).
219 * Args:
220 * base_name - base name for device (normally "eth")
221 * eth_number - value of %d (0 for first device of this type)
222 * Returns:
223 * 0 is success, non-zero is error status from driver.
224 */
225 int eth_write_hwaddr(struct eth_device *dev, const char *base_name,
226 int eth_number);
227
228 int usb_eth_initialize(bd_t *bi);
229 #endif
230
231 int eth_initialize(void); /* Initialize network subsystem */
232 void eth_try_another(int first_restart); /* Change the device */
233 void eth_set_current(void); /* set nterface to ethcur var */
234
235 int eth_get_dev_index(void); /* get the device index */
236 void eth_parse_enetaddr(const char *addr, uchar *enetaddr);
237 int eth_getenv_enetaddr(const char *name, uchar *enetaddr);
238 int eth_setenv_enetaddr(const char *name, const uchar *enetaddr);
239
240 /**
241 * eth_setenv_enetaddr_by_index() - set the MAC address envrionment variable
242 *
243 * This sets up an environment variable with the given MAC address (@enetaddr).
244 * The environment variable to be set is defined by <@base_name><@index>addr.
245 * If @index is 0 it is omitted. For common Ethernet this means ethaddr,
246 * eth1addr, etc.
247 *
248 * @base_name: Base name for variable, typically "eth"
249 * @index: Index of interface being updated (>=0)
250 * @enetaddr: Pointer to MAC address to put into the variable
251 * @return 0 if OK, other value on error
252 */
253 int eth_setenv_enetaddr_by_index(const char *base_name, int index,
254 uchar *enetaddr);
255
256
257 /*
258 * Get the hardware address for an ethernet interface .
259 * Args:
260 * base_name - base name for device (normally "eth")
261 * index - device index number (0 for first)
262 * enetaddr - returns 6 byte hardware address
263 * Returns:
264 * Return true if the address is valid.
265 */
266 int eth_getenv_enetaddr_by_index(const char *base_name, int index,
267 uchar *enetaddr);
268
269 int eth_init(void); /* Initialize the device */
270 int eth_send(void *packet, int length); /* Send a packet */
271
272 #if defined(CONFIG_API) || defined(CONFIG_EFI_LOADER)
273 int eth_receive(void *packet, int length); /* Receive a packet*/
274 extern void (*push_packet)(void *packet, int length);
275 #endif
276 int eth_rx(void); /* Check for received packets */
277 void eth_halt(void); /* stop SCC */
278 const char *eth_get_name(void); /* get name of current device */
279
280 #ifdef CONFIG_MCAST_TFTP
281 int eth_mcast_join(struct in_addr mcast_addr, int join);
282 u32 ether_crc(size_t len, unsigned char const *p);
283 #endif
284
285
286 /**********************************************************************/
287 /*
288 * Protocol headers.
289 */
290
291 /*
292 * Ethernet header
293 */
294
295 struct ethernet_hdr {
296 u8 et_dest[6]; /* Destination node */
297 u8 et_src[6]; /* Source node */
298 u16 et_protlen; /* Protocol or length */
299 };
300
301 /* Ethernet header size */
302 #define ETHER_HDR_SIZE (sizeof(struct ethernet_hdr))
303
304 #define ETH_FCS_LEN 4 /* Octets in the FCS */
305
306 struct e802_hdr {
307 u8 et_dest[6]; /* Destination node */
308 u8 et_src[6]; /* Source node */
309 u16 et_protlen; /* Protocol or length */
310 u8 et_dsap; /* 802 DSAP */
311 u8 et_ssap; /* 802 SSAP */
312 u8 et_ctl; /* 802 control */
313 u8 et_snap1; /* SNAP */
314 u8 et_snap2;
315 u8 et_snap3;
316 u16 et_prot; /* 802 protocol */
317 };
318
319 /* 802 + SNAP + ethernet header size */
320 #define E802_HDR_SIZE (sizeof(struct e802_hdr))
321
322 /*
323 * Virtual LAN Ethernet header
324 */
325 struct vlan_ethernet_hdr {
326 u8 vet_dest[6]; /* Destination node */
327 u8 vet_src[6]; /* Source node */
328 u16 vet_vlan_type; /* PROT_VLAN */
329 u16 vet_tag; /* TAG of VLAN */
330 u16 vet_type; /* protocol type */
331 };
332
333 /* VLAN Ethernet header size */
334 #define VLAN_ETHER_HDR_SIZE (sizeof(struct vlan_ethernet_hdr))
335
336 #define PROT_IP 0x0800 /* IP protocol */
337 #define PROT_ARP 0x0806 /* IP ARP protocol */
338 #define PROT_RARP 0x8035 /* IP ARP protocol */
339 #define PROT_VLAN 0x8100 /* IEEE 802.1q protocol */
340 #define PROT_IPV6 0x86dd /* IPv6 over bluebook */
341 #define PROT_PPP_SES 0x8864 /* PPPoE session messages */
342
343 #define IPPROTO_ICMP 1 /* Internet Control Message Protocol */
344 #define IPPROTO_UDP 17 /* User Datagram Protocol */
345
346 /*
347 * Internet Protocol (IP) header.
348 */
349 struct ip_hdr {
350 u8 ip_hl_v; /* header length and version */
351 u8 ip_tos; /* type of service */
352 u16 ip_len; /* total length */
353 u16 ip_id; /* identification */
354 u16 ip_off; /* fragment offset field */
355 u8 ip_ttl; /* time to live */
356 u8 ip_p; /* protocol */
357 u16 ip_sum; /* checksum */
358 struct in_addr ip_src; /* Source IP address */
359 struct in_addr ip_dst; /* Destination IP address */
360 };
361
362 #define IP_OFFS 0x1fff /* ip offset *= 8 */
363 #define IP_FLAGS 0xe000 /* first 3 bits */
364 #define IP_FLAGS_RES 0x8000 /* reserved */
365 #define IP_FLAGS_DFRAG 0x4000 /* don't fragments */
366 #define IP_FLAGS_MFRAG 0x2000 /* more fragments */
367
368 #define IP_HDR_SIZE (sizeof(struct ip_hdr))
369
370 /*
371 * Internet Protocol (IP) + UDP header.
372 */
373 struct ip_udp_hdr {
374 u8 ip_hl_v; /* header length and version */
375 u8 ip_tos; /* type of service */
376 u16 ip_len; /* total length */
377 u16 ip_id; /* identification */
378 u16 ip_off; /* fragment offset field */
379 u8 ip_ttl; /* time to live */
380 u8 ip_p; /* protocol */
381 u16 ip_sum; /* checksum */
382 struct in_addr ip_src; /* Source IP address */
383 struct in_addr ip_dst; /* Destination IP address */
384 u16 udp_src; /* UDP source port */
385 u16 udp_dst; /* UDP destination port */
386 u16 udp_len; /* Length of UDP packet */
387 u16 udp_xsum; /* Checksum */
388 };
389
390 #define IP_UDP_HDR_SIZE (sizeof(struct ip_udp_hdr))
391 #define UDP_HDR_SIZE (IP_UDP_HDR_SIZE - IP_HDR_SIZE)
392
393 /*
394 * Address Resolution Protocol (ARP) header.
395 */
396 struct arp_hdr {
397 u16 ar_hrd; /* Format of hardware address */
398 # define ARP_ETHER 1 /* Ethernet hardware address */
399 u16 ar_pro; /* Format of protocol address */
400 u8 ar_hln; /* Length of hardware address */
401 # define ARP_HLEN 6
402 u8 ar_pln; /* Length of protocol address */
403 # define ARP_PLEN 4
404 u16 ar_op; /* Operation */
405 # define ARPOP_REQUEST 1 /* Request to resolve address */
406 # define ARPOP_REPLY 2 /* Response to previous request */
407
408 # define RARPOP_REQUEST 3 /* Request to resolve address */
409 # define RARPOP_REPLY 4 /* Response to previous request */
410
411 /*
412 * The remaining fields are variable in size, according to
413 * the sizes above, and are defined as appropriate for
414 * specific hardware/protocol combinations.
415 */
416 u8 ar_data[0];
417 #define ar_sha ar_data[0]
418 #define ar_spa ar_data[ARP_HLEN]
419 #define ar_tha ar_data[ARP_HLEN + ARP_PLEN]
420 #define ar_tpa ar_data[ARP_HLEN + ARP_PLEN + ARP_HLEN]
421 #if 0
422 u8 ar_sha[]; /* Sender hardware address */
423 u8 ar_spa[]; /* Sender protocol address */
424 u8 ar_tha[]; /* Target hardware address */
425 u8 ar_tpa[]; /* Target protocol address */
426 #endif /* 0 */
427 };
428
429 #define ARP_HDR_SIZE (8+20) /* Size assuming ethernet */
430
431 /*
432 * ICMP stuff (just enough to handle (host) redirect messages)
433 */
434 #define ICMP_ECHO_REPLY 0 /* Echo reply */
435 #define ICMP_NOT_REACH 3 /* Detination unreachable */
436 #define ICMP_REDIRECT 5 /* Redirect (change route) */
437 #define ICMP_ECHO_REQUEST 8 /* Echo request */
438
439 /* Codes for REDIRECT. */
440 #define ICMP_REDIR_NET 0 /* Redirect Net */
441 #define ICMP_REDIR_HOST 1 /* Redirect Host */
442
443 /* Codes for NOT_REACH */
444 #define ICMP_NOT_REACH_PORT 3 /* Port unreachable */
445
446 struct icmp_hdr {
447 u8 type;
448 u8 code;
449 u16 checksum;
450 union {
451 struct {
452 u16 id;
453 u16 sequence;
454 } echo;
455 u32 gateway;
456 struct {
457 u16 unused;
458 u16 mtu;
459 } frag;
460 u8 data[0];
461 } un;
462 };
463
464 #define ICMP_HDR_SIZE (sizeof(struct icmp_hdr))
465 #define IP_ICMP_HDR_SIZE (IP_HDR_SIZE + ICMP_HDR_SIZE)
466
467 /*
468 * Maximum packet size; used to allocate packet storage. Use
469 * the maxium Ethernet frame size as specified by the Ethernet
470 * standard including the 802.1Q tag (VLAN tagging).
471 * maximum packet size = 1522
472 * maximum packet size and multiple of 32 bytes = 1536
473 */
474 #define PKTSIZE 1522
475 #define PKTSIZE_ALIGN 1536
476
477 /*
478 * Maximum receive ring size; that is, the number of packets
479 * we can buffer before overflow happens. Basically, this just
480 * needs to be enough to prevent a packet being discarded while
481 * we are processing the previous one.
482 */
483 #define RINGSZ 4
484 #define RINGSZ_LOG2 2
485
486 /**********************************************************************/
487 /*
488 * Globals.
489 *
490 * Note:
491 *
492 * All variables of type struct in_addr are stored in NETWORK byte order
493 * (big endian).
494 */
495
496 /* net.c */
497 /** BOOTP EXTENTIONS **/
498 extern struct in_addr net_gateway; /* Our gateway IP address */
499 extern struct in_addr net_netmask; /* Our subnet mask (0 = unknown) */
500 /* Our Domain Name Server (0 = unknown) */
501 extern struct in_addr net_dns_server;
502 #if defined(CONFIG_BOOTP_DNS2)
503 /* Our 2nd Domain Name Server (0 = unknown) */
504 extern struct in_addr net_dns_server2;
505 #endif
506 extern char net_nis_domain[32]; /* Our IS domain */
507 extern char net_hostname[32]; /* Our hostname */
508 extern char net_root_path[64]; /* Our root path */
509 /** END OF BOOTP EXTENTIONS **/
510 extern u8 net_ethaddr[6]; /* Our ethernet address */
511 extern u8 net_server_ethaddr[6]; /* Boot server enet address */
512 extern struct in_addr net_ip; /* Our IP addr (0 = unknown) */
513 extern struct in_addr net_server_ip; /* Server IP addr (0 = unknown) */
514 extern uchar *net_tx_packet; /* THE transmit packet */
515 extern uchar *net_rx_packets[PKTBUFSRX]; /* Receive packets */
516 extern uchar *net_rx_packet; /* Current receive packet */
517 extern int net_rx_packet_len; /* Current rx packet length */
518 extern const u8 net_bcast_ethaddr[6]; /* Ethernet broadcast address */
519 extern const u8 net_null_ethaddr[6];
520
521 #define VLAN_NONE 4095 /* untagged */
522 #define VLAN_IDMASK 0x0fff /* mask of valid vlan id */
523 extern ushort net_our_vlan; /* Our VLAN */
524 extern ushort net_native_vlan; /* Our Native VLAN */
525
526 extern int net_restart_wrap; /* Tried all network devices */
527
528 enum proto_t {
529 BOOTP, RARP, ARP, TFTPGET, DHCP, PING, DNS, NFS, CDP, NETCONS, SNTP,
530 TFTPSRV, TFTPPUT, LINKLOCAL
531 };
532
533 extern char net_boot_file_name[1024];/* Boot File name */
534 /* The actual transferred size of the bootfile (in bytes) */
535 extern u32 net_boot_file_size;
536 /* Boot file size in blocks as reported by the DHCP server */
537 extern u32 net_boot_file_expected_size_in_blocks;
538
539 #if defined(CONFIG_CMD_DNS)
540 extern char *net_dns_resolve; /* The host to resolve */
541 extern char *net_dns_env_var; /* the env var to put the ip into */
542 #endif
543
544 #if defined(CONFIG_CMD_PING)
545 extern struct in_addr net_ping_ip; /* the ip address to ping */
546 #endif
547
548 #if defined(CONFIG_CMD_CDP)
549 /* when CDP completes these hold the return values */
550 extern ushort cdp_native_vlan; /* CDP returned native VLAN */
551 extern ushort cdp_appliance_vlan; /* CDP returned appliance VLAN */
552
553 /*
554 * Check for a CDP packet by examining the received MAC address field
555 */
556 static inline int is_cdp_packet(const uchar *ethaddr)
557 {
558 extern const u8 net_cdp_ethaddr[6];
559
560 return memcmp(ethaddr, net_cdp_ethaddr, 6) == 0;
561 }
562 #endif
563
564 #if defined(CONFIG_CMD_SNTP)
565 extern struct in_addr net_ntp_server; /* the ip address to NTP */
566 extern int net_ntp_time_offset; /* offset time from UTC */
567 #endif
568
569 #if defined(CONFIG_MCAST_TFTP)
570 extern struct in_addr net_mcast_addr;
571 #endif
572
573 /* Initialize the network adapter */
574 void net_init(void);
575 int net_loop(enum proto_t);
576
577 /* Load failed. Start again. */
578 int net_start_again(void);
579
580 /* Get size of the ethernet header when we send */
581 int net_eth_hdr_size(void);
582
583 /* Set ethernet header; returns the size of the header */
584 int net_set_ether(uchar *xet, const uchar *dest_ethaddr, uint prot);
585 int net_update_ether(struct ethernet_hdr *et, uchar *addr, uint prot);
586
587 /* Set IP header */
588 void net_set_ip_header(uchar *pkt, struct in_addr dest, struct in_addr source);
589 void net_set_udp_header(uchar *pkt, struct in_addr dest, int dport,
590 int sport, int len);
591
592 /**
593 * compute_ip_checksum() - Compute IP checksum
594 *
595 * @addr: Address to check (must be 16-bit aligned)
596 * @nbytes: Number of bytes to check (normally a multiple of 2)
597 * @return 16-bit IP checksum
598 */
599 unsigned compute_ip_checksum(const void *addr, unsigned nbytes);
600
601 /**
602 * add_ip_checksums() - add two IP checksums
603 *
604 * @offset: Offset of first sum (if odd we do a byte-swap)
605 * @sum: First checksum
606 * @new_sum: New checksum to add
607 * @return updated 16-bit IP checksum
608 */
609 unsigned add_ip_checksums(unsigned offset, unsigned sum, unsigned new_sum);
610
611 /**
612 * ip_checksum_ok() - check if a checksum is correct
613 *
614 * This works by making sure the checksum sums to 0
615 *
616 * @addr: Address to check (must be 16-bit aligned)
617 * @nbytes: Number of bytes to check (normally a multiple of 2)
618 * @return true if the checksum matches, false if not
619 */
620 int ip_checksum_ok(const void *addr, unsigned nbytes);
621
622 /* Callbacks */
623 rxhand_f *net_get_udp_handler(void); /* Get UDP RX packet handler */
624 void net_set_udp_handler(rxhand_f *); /* Set UDP RX packet handler */
625 rxhand_f *net_get_arp_handler(void); /* Get ARP RX packet handler */
626 void net_set_arp_handler(rxhand_f *); /* Set ARP RX packet handler */
627 void net_set_icmp_handler(rxhand_icmp_f *f); /* Set ICMP RX handler */
628 void net_set_timeout_handler(ulong, thand_f *);/* Set timeout handler */
629
630 /* Network loop state */
631 enum net_loop_state {
632 NETLOOP_CONTINUE,
633 NETLOOP_RESTART,
634 NETLOOP_SUCCESS,
635 NETLOOP_FAIL
636 };
637 extern enum net_loop_state net_state;
638
639 static inline void net_set_state(enum net_loop_state state)
640 {
641 debug_cond(DEBUG_INT_STATE, "--- NetState set to %d\n", state);
642 net_state = state;
643 }
644
645 /* Transmit a packet */
646 static inline void net_send_packet(uchar *pkt, int len)
647 {
648 /* Currently no way to return errors from eth_send() */
649 (void) eth_send(pkt, len);
650 }
651
652 /*
653 * Transmit "net_tx_packet" as UDP packet, performing ARP request if needed
654 * (ether will be populated)
655 *
656 * @param ether Raw packet buffer
657 * @param dest IP address to send the datagram to
658 * @param dport Destination UDP port
659 * @param sport Source UDP port
660 * @param payload_len Length of data after the UDP header
661 */
662 int net_send_udp_packet(uchar *ether, struct in_addr dest, int dport,
663 int sport, int payload_len);
664
665 /* Processes a received packet */
666 void net_process_received_packet(uchar *in_packet, int len);
667
668 #ifdef CONFIG_NETCONSOLE
669 void nc_start(void);
670 int nc_input_packet(uchar *pkt, struct in_addr src_ip, unsigned dest_port,
671 unsigned src_port, unsigned len);
672 #endif
673
674 static __always_inline int eth_is_on_demand_init(void)
675 {
676 #ifdef CONFIG_NETCONSOLE
677 extern enum proto_t net_loop_last_protocol;
678
679 return net_loop_last_protocol != NETCONS;
680 #else
681 return 1;
682 #endif
683 }
684
685 static inline void eth_set_last_protocol(int protocol)
686 {
687 #ifdef CONFIG_NETCONSOLE
688 extern enum proto_t net_loop_last_protocol;
689
690 net_loop_last_protocol = protocol;
691 #endif
692 }
693
694 /*
695 * Check if autoload is enabled. If so, use either NFS or TFTP to download
696 * the boot file.
697 */
698 void net_auto_load(void);
699
700 /*
701 * The following functions are a bit ugly, but necessary to deal with
702 * alignment restrictions on ARM.
703 *
704 * We're using inline functions, which had the smallest memory
705 * footprint in our tests.
706 */
707 /* return IP *in network byteorder* */
708 static inline struct in_addr net_read_ip(void *from)
709 {
710 struct in_addr ip;
711
712 memcpy((void *)&ip, (void *)from, sizeof(ip));
713 return ip;
714 }
715
716 /* return ulong *in network byteorder* */
717 static inline u32 net_read_u32(u32 *from)
718 {
719 u32 l;
720
721 memcpy((void *)&l, (void *)from, sizeof(l));
722 return l;
723 }
724
725 /* write IP *in network byteorder* */
726 static inline void net_write_ip(void *to, struct in_addr ip)
727 {
728 memcpy(to, (void *)&ip, sizeof(ip));
729 }
730
731 /* copy IP */
732 static inline void net_copy_ip(void *to, void *from)
733 {
734 memcpy((void *)to, from, sizeof(struct in_addr));
735 }
736
737 /* copy ulong */
738 static inline void net_copy_u32(u32 *to, u32 *from)
739 {
740 memcpy((void *)to, (void *)from, sizeof(u32));
741 }
742
743 /**
744 * is_zero_ethaddr - Determine if give Ethernet address is all zeros.
745 * @addr: Pointer to a six-byte array containing the Ethernet address
746 *
747 * Return true if the address is all zeroes.
748 */
749 static inline int is_zero_ethaddr(const u8 *addr)
750 {
751 return !(addr[0] | addr[1] | addr[2] | addr[3] | addr[4] | addr[5]);
752 }
753
754 /**
755 * is_multicast_ethaddr - Determine if the Ethernet address is a multicast.
756 * @addr: Pointer to a six-byte array containing the Ethernet address
757 *
758 * Return true if the address is a multicast address.
759 * By definition the broadcast address is also a multicast address.
760 */
761 static inline int is_multicast_ethaddr(const u8 *addr)
762 {
763 return 0x01 & addr[0];
764 }
765
766 /*
767 * is_broadcast_ethaddr - Determine if the Ethernet address is broadcast
768 * @addr: Pointer to a six-byte array containing the Ethernet address
769 *
770 * Return true if the address is the broadcast address.
771 */
772 static inline int is_broadcast_ethaddr(const u8 *addr)
773 {
774 return (addr[0] & addr[1] & addr[2] & addr[3] & addr[4] & addr[5]) ==
775 0xff;
776 }
777
778 /*
779 * is_valid_ethaddr - Determine if the given Ethernet address is valid
780 * @addr: Pointer to a six-byte array containing the Ethernet address
781 *
782 * Check that the Ethernet address (MAC) is not 00:00:00:00:00:00, is not
783 * a multicast address, and is not FF:FF:FF:FF:FF:FF.
784 *
785 * Return true if the address is valid.
786 */
787 static inline int is_valid_ethaddr(const u8 *addr)
788 {
789 /* FF:FF:FF:FF:FF:FF is a multicast address so we don't need to
790 * explicitly check for it here. */
791 return !is_multicast_ethaddr(addr) && !is_zero_ethaddr(addr);
792 }
793
794 /**
795 * net_random_ethaddr - Generate software assigned random Ethernet address
796 * @addr: Pointer to a six-byte array containing the Ethernet address
797 *
798 * Generate a random Ethernet address (MAC) that is not multicast
799 * and has the local assigned bit set.
800 */
801 static inline void net_random_ethaddr(uchar *addr)
802 {
803 int i;
804 unsigned int seed = get_timer(0);
805
806 for (i = 0; i < 6; i++)
807 addr[i] = rand_r(&seed);
808
809 addr[0] &= 0xfe; /* clear multicast bit */
810 addr[0] |= 0x02; /* set local assignment bit (IEEE802) */
811 }
812
813 /* Convert an IP address to a string */
814 void ip_to_string(struct in_addr x, char *s);
815
816 /* Convert a string to ip address */
817 struct in_addr string_to_ip(const char *s);
818
819 /* Convert a VLAN id to a string */
820 void vlan_to_string(ushort x, char *s);
821
822 /* Convert a string to a vlan id */
823 ushort string_to_vlan(const char *s);
824
825 /* read a VLAN id from an environment variable */
826 ushort getenv_vlan(char *);
827
828 /* copy a filename (allow for "..." notation, limit length) */
829 void copy_filename(char *dst, const char *src, int size);
830
831 /* get a random source port */
832 unsigned int random_port(void);
833
834 /**
835 * update_tftp - Update firmware over TFTP (via DFU)
836 *
837 * This function updates board's firmware via TFTP
838 *
839 * @param addr - memory address where data is stored
840 * @param interface - the DFU medium name - e.g. "mmc"
841 * @param devstring - the DFU medium number - e.g. "1"
842 *
843 * @return - 0 on success, other value on failure
844 */
845 int update_tftp(ulong addr, char *interface, char *devstring);
846
847 /**********************************************************************/
848
849 #endif /* __NET_H__ */