The .read_rom_hwaddr net_ops hook does not check the return value, which
is why it was never caught that we are currently returning 0 if the
read_rom_hwaddr function return -ENOSYS and -ENOSYS otherwise.
In this case we can simplify this by just returning the result of the
function.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Michal Simek <michal.simek@xilinx.com>
Jacob Chen [Mon, 27 Mar 2017 08:54:17 +0000 (16:54 +0800)]
net: designware: Add phy supply support
Some board need a regulator for gmac phy, so add this code to handle it. Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Philipp Tomsich [Sun, 26 Mar 2017 16:50:23 +0000 (18:50 +0200)]
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable
This change migrate the following configuration options for Kconfig:
* PHY_GIGE, indicates that a controller (with an appropriate PHY) is
Gigabit capable and enables extra support in the miiutil for
parsing the status of Gigabit PHYs
* adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs,
which previously had to enabled through a board-specific config file
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Sat, 27 May 2017 13:38:27 +0000 (07:38 -0600)]
binman: Drop a special case related to fdt_fallback
Previously we were sometimes forced to collate x86 microcode due to not
having access to the offset of each individual piece. Now that we never
use fdt_fallback, we don't have this problem. Drop this special case from
the code.
Simon Glass [Sat, 27 May 2017 13:38:23 +0000 (07:38 -0600)]
fdt: Makefile: Build python libfdt library if needed
This is needed by binman and dtoc, so if those are being used, check that
the library is present and complain if not. Make sure that any error
appears on stderr so that buildman notices it.
This means that the fallback library (which uses fdtget) will not be used
anymore and swig will need to be installed to use binman / dtoc.
This affects any board which uses binman (currently sunxi and x86) or dtoc
(anything that uses CONFIG_SPL_OF_PLATDATA, currently some rockchip
boards).
Simon Glass [Sat, 27 May 2017 13:38:21 +0000 (07:38 -0600)]
fdt: dtoc: Add a full set of property tests
The tests don't currently cover all the different property types. Add a
new test which checks each property type in turn, to make sure each has
the correct type and value.
Simon Glass [Sat, 27 May 2017 13:38:18 +0000 (07:38 -0600)]
fdt: Rename existing python libfdt module
Now that this module has been accepted upstream we should stop using the
local U-Boot one. In preparation for this, rename it to indicate it is for
legacy use.
Simon Glass [Sat, 27 May 2017 13:38:17 +0000 (07:38 -0600)]
fdt: Add all source files to the libfdt build
At present only a subset of source files are build. Add the rest and
refactor this so that a source file list is available also. This will be
used in later commit.
Simon Glass [Sat, 27 May 2017 13:38:12 +0000 (07:38 -0600)]
pci: Correct cast for sandbox
This gives a warning with some native compilers:
cmd/pci.c:152:11: warning: format ‘%llx’ expects argument of type
‘long long unsigned int’, but argument 3 has type
‘u64 {aka long unsigned int}’ [-Wformat=]
CPU: Allwinner H5 (SUN50I)
Model: OrangePi Prime
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: phy interface7
eth0: ethernet@1c30000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
York Sun [Mon, 15 May 2017 15:52:00 +0000 (08:52 -0700)]
armv8: layerscape: Enabling loading PPA during SPL stage
Loading PPA in SPL puts the rest of U-Boot (including RAM version
loaded later) in EL2 with MMU and cache enabled. Once PPA is loaded,
PSCI is available.
York Sun [Mon, 15 May 2017 15:51:59 +0000 (08:51 -0700)]
armv8: layerscape: Make U-Boot EL2 safe
When U-Boot boots from EL2, skip some lowlevel init code requiring
EL3, including CCI-400/CCN-504, trust zone, GIC, etc. These
initialization tasks are carried out before U-Boot runs. This applies
to the RAM version image used for SPL boot if PPA is loaded first.
Santan Kumar [Fri, 5 May 2017 10:12:28 +0000 (15:42 +0530)]
armv8: ls2080a: Reorganise NAND_BOOT code in config flag
Add CONFIG_NAND_BOOT config flag to organise
NAND_BOOT specific code in config flag like
-nand-boot specfic errata errata_rcw_src()
-CONFIG_SYS_NAND_U_BOOT_DST,etc
Signed-off-by: Santan Kumar <santan.kumar@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
drivers: net: fsl-mc: Include MAC addr fixup to DPL
Previous to MC v10.x, port mac address was specified via DPL. Since
newer MC versions are compatible with old style DPLs, make the u-boot
env mac addresses visible there. This applies only to DPLs that have
an older version.
DPLs use 32 bit values for specifying MAC addresses. U-boot
environment variables take precedence over the MAC addresses already
visible in the DPL/DPC.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com> Signed-off-by: Heinz Wrobel <heinz.wrobel@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
DPAA2 platforms boot the Management Complex based on the u-boot env
variable "mcinitcmd". Instead of doing this step on each platform
individually, define a single mc_env_boot function in the MC driver,
since it's semantically tied to it.
Call the function in a per-board reset_phy hook, as it gets called at a
later moment, when all board PHY devices have been initialized.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com> Signed-off-by: Heinz Wrobel <heinz.wrobel@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Simon Glass [Fri, 19 May 2017 02:09:43 +0000 (20:09 -0600)]
dm: test: Separate out the bus DT offset test
We cannot access the device tree via an offset when running in livetree
mode. Separate out that part of the bus' children tests and mark it as
for the flat tree only.
Simon Glass [Fri, 19 May 2017 02:09:18 +0000 (20:09 -0600)]
dm: gpio: Refactor to prepare for live tree support
Move the main part of the GPIO request function into a separate function
so that it can be used by the live tree function when added. Update the
xlate method to use a node reference.
Update all GPIO drivers to handle the modified xlate() method.
Simon Glass [Fri, 19 May 2017 02:09:17 +0000 (20:09 -0600)]
dm: core: Run tests with both livetree and flat tree
Some tests require either livetree or flat tree. Add flags to allow the
tests to specify this. Adjust the test runner to run with livetree (if
supported) and then flat tree.
Some video tests are quite slow and running on flat tree adds little extra
test value, so run these on livetree only.
Simon Glass [Fri, 19 May 2017 02:09:16 +0000 (20:09 -0600)]
dm: test: Add support for running tests with livetree
It is useful to run the driver model tests with both livetree and flat
tree in case something is different between the two. Add this feature to
the test runner.
Simon Glass [Fri, 19 May 2017 02:09:13 +0000 (20:09 -0600)]
sandbox: Add a way to reset sandbox state for tests
Running a new test should reset the sandbox state to avoid tests
interferring with each other. Move the existing state-reset code into a
function so it can be used from tests.
Also update the code to reset the SPI devices and adjust the test code to
call it.
Simon Glass [Fri, 19 May 2017 02:09:03 +0000 (20:09 -0600)]
dm: core: Add device-based 'read' functions to access DT
It is common to read a device-tree property from the node associated with
a device. Add convenience functions to do this so that drivers do not need
to deal with accessing the ofnode from the device.
These functions all start with 'dev_read_' to provide consistent naming
for all functions which read information from a device's device tree node.
These are inlined when using the flat DT to save code size. The live tree
implementation is added in a later commit.
Simon Glass [Fri, 19 May 2017 02:09:02 +0000 (20:09 -0600)]
dm: core: Add a place to put extra device-tree reading functions
Some functions deal with structured data rather than simple data types.
It makes sense to have these in their own file. For now this just has a
function to read a flashmap entry. Move the data types also.