Wolfgang Denk [Sat, 28 Mar 2009 23:58:16 +0000 (00:58 +0100)]
VCMA9: fix compile errors
Fix these:
cmd_vcma9.c:82: warning: implicit declaration of function 'eth_getenv_enetaddr'
cmd_vcma9.c:89: error: 'enetaddr' undeclared (first use in this function)
Ladislav Michl [Mon, 23 Mar 2009 17:16:34 +0000 (18:16 +0100)]
cs8900 compile fix
cs8900.c: In function 'eth_init':
cs8900.c:164: warning: passing argument 2 of 'eth_getenv_enetaddr' from incompatible pointer type
cs8900.c:165: error: invalid operands to binary <<
cs8900.c:166: error: invalid operands to binary <<
cs8900.c:167: error: invalid operands to binary <<
Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Stefan Roese [Thu, 26 Mar 2009 15:14:13 +0000 (16:14 +0100)]
ppc4xx: Sequoia: Fix TLB reassignment in NAND booting code
This patch fixes a bug in the Sequoia TLB init code to reconfigure
the correct TLB (boot space) after running from RAM. This bug was
introduced with patch 4d332dbeb08f5863d1ea69d91a00c5499d3a87ed
[ppc4xx: Make Sequoia boot vxWorks] which changed the order of the
TLB in the Sequoia init.S file.
Jon Smirl [Mon, 23 Mar 2009 02:55:45 +0000 (22:55 -0400)]
mpc5200: suppress printf until console initialized
On boards which have the environment in eeprom, i2c_init() is called
before the console and RAM are initialized.
Suppress printfs until the console is initialized.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com> Acked-by: Heiko Schocher <hs@denx.de>
Nishanth Menon [Wed, 25 Mar 2009 21:13:56 +0000 (22:13 +0100)]
OMAP3:Beagle: Enable mtdparts
http://www.denx.de/wiki/DULG/UBootCmdGroupFlash#UBootCmdFlMtdparts
provides a flexible way to create and maintain u-boot mtd
partitions. This allows commands such as "nand erase fs"
to work and the user no longer needs to decode the absolute
nand offsets. This patch enables this function for beagleboard
Mike Frysinger [Sun, 1 Jun 2008 13:09:48 +0000 (09:09 -0400)]
Blackfin: unify common ADI board settings
Rather than duplicate the same ADI settings in every ADI board, create a
common ADI config header and have all ADI boards start using that. This
will also make merging the ~10 boards I have to forward port a lot easier.
Kyungmin Park [Tue, 3 Mar 2009 00:05:53 +0000 (09:05 +0900)]
Reduce OneNAND IPL common code
OneNAND IPL has common codes for RAM init, load data, and jump to 2nd
bootloader, but it's common code used about 300~400 bytes. So board
specific codes, such as lowlevel_init, can't has enough code. It make
a difficult to implement OneNAND IPL.
his patch make this common code as small as possible. and give
lowlevel_init can have more codes.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Add wait flags to support board/chip specific delays
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Add support for TQM-specific chip select logic to FSL-UPM
For the NAND chips on the TQM8548 modules, a special chip-select logic is
used. It uses dedicated address lines to be set via UPM machine address
register (mar). This patch adds such support to the FSL-UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Mike Frysinger [Sun, 12 Oct 2008 01:58:33 +0000 (21:58 -0400)]
Blackfin: put memory into self-refresh before/after programming clocks
When initializing the core clocks, stick external memory into self-refresh.
This gains us a few cool things:
- support suspend-to-RAM with Linux
- reprogram clocks automatically when doing "go" on u-boot.bin in RAM
- make sure settings are stable before flashing new version
- finally fully unify initialize startup code path between LDR/non-LDR
Mike Frysinger [Sat, 6 Dec 2008 23:06:58 +0000 (18:06 -0500)]
Blackfin: handle reboot anomaly 432
Workaround anomaly 432:
The bfrom_SysControl() firmware function does not clear the SIC_IWR1
register before executing the PLL programming sequence. Therefore, any
interrupt enabled in the SIC_IWR1 register prior to the call to
bfrom_SysControl() can prematurely terminate the idle sequence required
for the PLL to relock properly. SIC_IWR0 is properly handled.
Mike Frysinger [Mon, 6 Oct 2008 08:01:26 +0000 (04:01 -0400)]
Blackfin: print out Flash: before checking it
If there is some problem in the flash init/checking code, it's nicer to see
the message "Flash:" before crashing. This way the source of the problem
is a bit more straightforward.
Mike Frysinger [Tue, 17 Mar 2009 17:58:23 +0000 (13:58 -0400)]
Blackfin: fix jtag console tstc
The jtag tstc operation was checking the hardware to see if data is
available from it (which is fine for the jtag getc operation), but the
higher layers need to know whether any data is available. Since we have
to read up to 4 bytes at a time from the hardware, the higher layers need
to know they can consume the cached bytes as well.
Eric Schumann [Sat, 21 Mar 2009 13:59:34 +0000 (09:59 -0400)]
Make flash protection work, when the environment is in EEPROM
On the pcm030 the environment is located in the onboard EEPROM. But we want
to handle flash sector protection in a safe manner. So we must read the
unlock environment variable from EEPROM instead from flash.
This patch is required as long the evironment is saved into the EEPROM.
Stefan: Additional change as suggested by Wolfgang, use bigger char array
(instead of 4).
Signed-off-by: Eric Schumann <E.Schumann@phytec.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Michael Lawnick [Thu, 19 Mar 2009 09:06:41 +0000 (10:06 +0100)]
UBIFS: Missing offset relocation for compressor 'none'
On systems where U-Boot is linked to another address than it really lays
(e.g. backup image), calls via function pointers must be fixed with a
'+= gd->reloc_off'.
This was not done for none_compr in ubifs_compressors_init() what leads
to system crash on ubifsmount command.
Signed-off-by: Michael Lawnick <ml.lawnick@gmx.de> Acked-by: Stefan Roese <sr@denx.de>
Stefan Roese [Thu, 19 Mar 2009 14:35:05 +0000 (15:35 +0100)]
UBIFS: Implement read-only UBIFS support in U-Boot
The U-Boot UBIFS implementation is largely a direct copy from the current
Linux version (2.6.29-rc6). As already done in the UBI version we have an
"abstraction layer" to redefine or remove some OS calls (e.g. mutex_lock()
...). This makes it possible to use the original Linux code with very
little changes. And by this we can better update to later Linux versions.
I removed some of the Linux features that are not used in the U-Boot
version (e.g. garbage-collection, write support).
Signed-off-by: Stefan Roese <sr@denx.de> CC: Artem Bityutskiy <dedekind@infradead.org> CC: Adrian Hunter <ext-Adrian.Hunter@nokia.com>
Stefan Roese [Thu, 19 Mar 2009 14:34:56 +0000 (15:34 +0100)]
Add LZO decompressor support
This patch adds LZO decompression support to U-Boot. It is needed for
the upcoming UBIFS support, since UBIFS uses LZO as default compressor/
decompressor. Since we only support read-only in UBIFS, only the
decompressor is needed.
All this is copied with minor changes from the current Linux kernel
version (2.6.28-rc8).
This patch only implements this LZO decompressor support for PPC.
Other platforms using UBIFS will have to add the required
"include/asm/unaligned.h" as well. It should be fairly easy to copy this
from the Linux source tree as I have done it for PPC in this patch.
Stefan Roese [Thu, 19 Mar 2009 12:30:36 +0000 (13:30 +0100)]
Separate mtdparts command from jffs2
Currently the mtdparts commands are included in the jffs2 command support.
This doesn't make sense anymore since other commands (e.g. UBI) use this
infrastructure as well now. This patch separates the mtdparts commands from
the jffs2 commands making it possible to only select mtdparts when no JFFS2
support is needed.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Graeme Russ [Tue, 24 Feb 2009 10:14:32 +0000 (21:14 +1100)]
Factor out SC520 sub-features
Moved sub-features of the SC520 code which is currently selectively compiled
using #ifdef out of sc520.c into individual files selectively compiled via
the makefile
Signed-off-by: Graeme Russ <graeme.russ at gmail.com>
projects / people / ms / u-boot.git / log
