QCA vendor command support for TWT test configuration

[thirdparty/hostap.git] / src / common / qca-vendor.h

/*
 * Qualcomm Atheros OUI and vendor specific assignments
 * Copyright (c) 2014-2017, Qualcomm Atheros, Inc.
 * Copyright (c) 2018, The Linux Foundation
 *
 * This software may be distributed under the terms of the BSD license.
 * See README for more details.
 */

#ifndef QCA_VENDOR_H
#define QCA_VENDOR_H

/*
 * This file is a registry of identifier assignments from the Qualcomm Atheros
 * OUI 00:13:74 for purposes other than MAC address assignment. New identifiers
 * can be assigned through normal review process for changes to the upstream
 * hostap.git repository.
 */

#define OUI_QCA 0x001374

/**
 * enum qca_radiotap_vendor_ids - QCA radiotap vendor namespace IDs
 */
enum qca_radiotap_vendor_ids {
        QCA_RADIOTAP_VID_WLANTEST = 0,
};

/**
 * enum qca_nl80211_vendor_subcmds - QCA nl80211 vendor command identifiers
 *
 * @QCA_NL80211_VENDOR_SUBCMD_UNSPEC: Reserved value 0
 *
 * @QCA_NL80211_VENDOR_SUBCMD_TEST: Test command/event
 *
 * @QCA_NL80211_VENDOR_SUBCMD_ROAMING: Set roaming policy for drivers that use
 *      internal BSS-selection. This command uses
 *      @QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY to specify the new roaming policy
 *      for the current connection (i.e., changes policy set by the nl80211
 *      Connect command). @QCA_WLAN_VENDOR_ATTR_MAC_ADDR may optionally be
 *      included to indicate which BSS to use in case roaming is disabled.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY: Recommendation of frequency
 *      ranges to avoid to reduce issues due to interference or internal
 *      co-existence information in the driver. The event data structure is
 *      defined in struct qca_avoid_freq_list.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY: Command to check driver support
 *      for DFS offloading.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_NAN: NAN command/event which is used to pass
 *      NAN Request/Response and NAN Indication messages. These messages are
 *      interpreted between the framework and the firmware component. While
 *      sending the command from userspace to the driver, payload is not
 *      encapsulated inside any attribute. Attribute QCA_WLAN_VENDOR_ATTR_NAN
 *      is used when receiving vendor events in userspace from the driver.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY: Set key operation that can be
 *      used to configure PMK to the driver even when not connected. This can
 *      be used to request offloading of key management operations. Only used
 *      if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH: An extended version of
 *      NL80211_CMD_ROAM event with optional attributes including information
 *      from offloaded key management operation. Uses
 *      enum qca_wlan_vendor_attr_roam_auth attributes. Only used
 *      if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_DO_ACS: ACS command/event which is used to
 *      invoke the ACS function in device and pass selected channels to
 *      hostapd.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES: Command to get the features
 *      supported by the driver. enum qca_wlan_vendor_features defines
 *      the possible features.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED: Event used by driver,
 *      which supports DFS offloading, to indicate a channel availability check
 *      start.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED: Event used by driver,
 *      which supports DFS offloading, to indicate a channel availability check
 *      completion.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED: Event used by driver,
 *      which supports DFS offloading, to indicate that the channel availability
 *      check aborted, no change to the channel status.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED: Event used by
 *      driver, which supports DFS offloading, to indicate that the
 *      Non-Occupancy Period for this channel is over, channel becomes usable.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED: Event used by driver,
 *      which supports DFS offloading, to indicate a radar pattern has been
 *      detected. The channel is now unusable.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: Get the feature bitmap
 *      based on enum wifi_logger_supported_features. Attributes defined in
 *      enum qca_wlan_vendor_attr_get_logger_features.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA: Get the ring data from a particular
 *      logger ring, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID is passed as the
 *      attribute for this command. Attributes defined in
 *      enum qca_wlan_vendor_attr_wifi_logger_start.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES: Get the supported TDLS
 *      capabilities of the driver, parameters includes the attributes defined
 *      in enum qca_wlan_vendor_attr_tdls_get_capabilities.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS: Vendor command used to offload
 *      sending of certain periodic IP packet to firmware, attributes defined in
 *      enum qca_wlan_vendor_attr_offloaded_packets.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI: Command used to configure RSSI
 *      monitoring, defines min and max RSSI which are configured for RSSI
 *      monitoring. Also used to notify the RSSI breach and provides the BSSID
 *      and RSSI value that was breached. Attributes defined in
 *      enum qca_wlan_vendor_attr_rssi_monitoring.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_NDP: Command used for performing various NAN
 *      Data Path (NDP) related operations, attributes defined in
 *      enum qca_wlan_vendor_attr_ndp_params.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD: Command used to enable/disable
 *      Neighbour Discovery offload, attributes defined in
 *      enum qca_wlan_vendor_attr_nd_offload.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER: Used to set/get the various
 *      configuration parameter for BPF packet filter, attributes defined in
 *      enum qca_wlan_vendor_attr_packet_filter.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE: Gets the driver-firmware
 *      maximum supported size, attributes defined in
 *      enum qca_wlan_vendor_drv_info.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS: Command to get various
 *      data about wake reasons and datapath IP statistics, attributes defined
 *      in enum qca_wlan_vendor_attr_wake_stats.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG: Command used to set configuration
 *      for IEEE 802.11 communicating outside the context of a basic service
 *      set, called OCB command. Uses the attributes defines in
 *      enum qca_wlan_vendor_attr_ocb_set_config.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME: Command used to set OCB
 *      UTC time. Use the attributes defines in
 *      enum qca_wlan_vendor_attr_ocb_set_utc_time.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT: Command used to start
 *      sending OCB timing advert frames. Uses the attributes defines in
 *      enum qca_wlan_vendor_attr_ocb_start_timing_advert.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT: Command used to stop
 *      OCB timing advert. Uses the attributes defines in
 *      enum qca_wlan_vendor_attr_ocb_stop_timing_advert.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER: Command used to get TSF
 *      timer value. Uses the attributes defines in
 *      enum qca_wlan_vendor_attr_ocb_get_tsf_resp.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to
 *      start the P2P Listen offload function in device and pass the listen
 *      channel, period, interval, count, device types, and vendor specific
 *      information elements to the device driver and firmware.
 *      Uses the attributes defines in
 *      enum qca_wlan_vendor_attr_p2p_listen_offload.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP: Command/event used to
 *      indicate stop request/response of the P2P Listen offload function in
 *      device. As an event, it indicates either the feature stopped after it
 *      was already running or feature has actually failed to start. Uses the
 *      attributes defines in enum qca_wlan_vendor_attr_p2p_listen_offload.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After AP starts
 *      beaconing, this sub command provides the driver, the frequencies on the
 *      5 GHz band to check for any radar activity. Driver selects one channel
 *      from this priority list provided through
 *      @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts
 *      to check for radar activity on it. If no radar activity is detected
 *      during the channel availability check period, driver internally switches
 *      to the selected frequency of operation. If the frequency is zero, driver
 *      internally selects a channel. The status of this conditional switch is
 *      indicated through an event using the same sub command through
 *      @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are
 *      listed in qca_wlan_vendor_attr_sap_conditional_chan_switch.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND: Set GPIO pins. This uses the
 *      attributes defined in enum qca_wlan_gpio_attr.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY: Fetch hardware capabilities.
 *      This uses @QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY to indicate which
 *      capabilities are to be fetched and other
 *      enum qca_wlan_vendor_attr_get_hw_capability attributes to return the
 *      requested capabilities.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Link layer statistics extension.
 *      enum qca_wlan_vendor_attr_ll_stats_ext attributes are used with this
 *      command and event.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA: Get capabilities for
 *      indoor location features. Capabilities are reported in
 *      QCA_WLAN_VENDOR_ATTR_LOC_CAPA.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION: Start an FTM
 *      (fine timing measurement) session with one or more peers.
 *      Specify Session cookie in QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE and
 *      peer information in QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS.
 *      On success, 0 or more QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT
 *      events will be reported, followed by
 *      QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE event to indicate
 *      end of session.
 *      Refer to IEEE P802.11-REVmc/D7.0, 11.24.6
 *
 * @QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION: Abort a running session.
 *      A QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE will be reported with
 *      status code indicating session was aborted.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT: Event with measurement
 *      results for one peer. Results are reported in
 *      QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE: Event triggered when
 *      FTM session is finished, either successfully or aborted by
 *      request.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER: Configure FTM responder
 *      mode. QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE specifies whether
 *      to enable or disable the responder. LCI/LCR reports can be
 *      configured with QCA_WLAN_VENDOR_ATTR_FTM_LCI and
 *      QCA_WLAN_VENDOR_ATTR_FTM_LCR. Can be called multiple
 *      times to update the LCI/LCR reports.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS: Perform a standalone AOA (angle of
 *      arrival) measurement with a single peer. Specify peer MAC address in
 *      QCA_WLAN_VENDOR_ATTR_MAC_ADDR and optionally frequency (MHz) in
 *      QCA_WLAN_VENDOR_ATTR_FREQ (if not specified, locate peer in kernel
 *      scan results cache and use the frequency from there).
 *      Also specify measurement type in QCA_WLAN_VENDOR_ATTR_AOA_TYPE.
 *      Measurement result is reported in
 *      QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT event.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS: Abort an AOA measurement. Specify
 *      peer MAC address in QCA_WLAN_VENDOR_ATTR_MAC_ADDR.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT: Event that reports
 *      the AOA measurement result.
 *      Peer MAC address reported in QCA_WLAN_VENDOR_ATTR_MAC_ADDR.
 *      success/failure status is reported in
 *      QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS.
 *      Measurement data is reported in QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT.
 *      The antenna array(s) used in the measurement are reported in
 *      QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST: Encrypt/decrypt the given
 *      data as per the given parameters.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI: Get antenna RSSI value for a
 *      specific chain.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG: Get low level
 *      configuration for a DMG RF sector. Specify sector index in
 *      QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in
 *      QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and RF modules
 *      to return sector information for in
 *      QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK. Returns sector configuration
 *      in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG. Also return the
 *      exact time where information was captured in
 *      QCA_WLAN_VENDOR_ATTR_TSF.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG: Set low level
 *      configuration for a DMG RF sector. Specify sector index in
 *      QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in
 *      QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and sector configuration
 *      for one or more DMG RF modules in
 *      QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR: Get selected
 *      DMG RF sector for a station. This is the sector that the HW
 *      will use to communicate with the station. Specify the MAC address
 *      of associated station/AP/PCP in QCA_WLAN_VENDOR_ATTR_MAC_ADDR (not
 *      needed for unassociated station). Specify sector type to return in
 *      QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE. Returns the selected
 *      sector index in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX.
 *      Also return the exact time where the information was captured
 *      in QCA_WLAN_VENDOR_ATTR_TSF.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR: Set the
 *      selected DMG RF sector for a station. This is the sector that
 *      the HW will use to communicate with the station.
 *      Specify the MAC address of associated station/AP/PCP in
 *      QCA_WLAN_VENDOR_ATTR_MAC_ADDR, the sector type to select in
 *      QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and the sector index
 *      in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX.
 *      The selected sector will be locked such that it will not be
 *      modified like it normally does (for example when station
 *      moves around). To unlock the selected sector for a station
 *      pass the special value 0xFFFF in the sector index. To unlock
 *      all connected stations also pass a broadcast MAC address.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS: Configure the TDLS behavior
 *      in the host driver. The different TDLS configurations are defined
 *      by the attributes in enum qca_wlan_vendor_attr_tdls_configuration.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES: Query device IEEE 802.11ax HE
 *      capabilities. The response uses the attributes defined in
 *      enum qca_wlan_vendor_attr_get_he_capabilities.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN: Abort an ongoing vendor scan that was
 *      started with QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN. This command
 *      carries the scan cookie of the corresponding scan request. The scan
 *      cookie is represented by QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS: Set the Specific
 *      Absorption Rate (SAR) power limits. A critical regulation for
 *      FCC compliance, OEMs require methods to set SAR limits on TX
 *      power of WLAN/WWAN. enum qca_vendor_attr_sar_limits
 *      attributes are used with this command.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS: This command/event is used by the
 *      host driver for offloading the implementation of Auto Channel Selection
 *      (ACS) to an external user space entity. This interface is used as the
 *      event from the host driver to the user space entity and also as the
 *      request from the user space entity to the host driver. The event from
 *      the host driver is used by the user space entity as an indication to
 *      start the ACS functionality. The attributes used by this event are
 *      represented by the enum qca_wlan_vendor_attr_external_acs_event.
 *      User space entity uses the same interface to inform the host driver with
 *      selected channels after the ACS operation using the attributes defined
 *      by enum qca_wlan_vendor_attr_external_acs_channels.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE: Vendor event carrying the
 *      requisite information leading to a power save failure. The information
 *      carried as part of this event is represented by the
 *      enum qca_attr_chip_power_save_failure attributes.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET: Start/Stop the NUD statistics
 *      collection. Uses attributes defined in enum qca_attr_nud_stats_set.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET: Get the NUD statistics. These
 *      statistics are represented by the enum qca_attr_nud_stats_get
 *      attributes.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS: Sub-command to fetch
 *      the BSS transition status, whether accept or reject, for a list of
 *      candidate BSSIDs provided by the userspace. This uses the vendor
 *      attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and
 *      QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. The userspace shall specify
 *      the attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and an
 *      array of QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID nested in
 *      QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO in the request. In the response
 *      the driver shall specify array of
 *      QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID and
 *      QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS pairs nested in
 *      QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL: Set the trace level for a
 *      specific QCA module. The trace levels are represented by
 *      enum qca_attr_trace_level attributes.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT: Set the Beam Refinement
 *      Protocol antenna limit in different modes. See enum
 *      qca_wlan_vendor_attr_brp_ant_limit_mode.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START: Start spectral scan. The scan
 *      parameters are specified by enum qca_wlan_vendor_attr_spectral_scan.
 *      This returns a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE)
 *      identifying the operation in success case.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP: Stop spectral scan. This uses
 *      a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) from
 *      @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START to identify the scan to
 *      be stopped.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS: Set the active Type Of Service on the
 *      specific interface. This can be used to modify some of the low level
 *      scan parameters (off channel dwell time, home channel time) in the
 *      driver/firmware. These parameters are maintained within the host driver.
 *      This command is valid only when the interface is in the connected state.
 *      These scan parameters shall be reset by the driver/firmware once
 *      disconnected. The attributes used with this command are defined in
 *      enum qca_wlan_vendor_attr_active_tos.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_HANG: Event indicating to the user space that the
 *      driver has detected an internal failure. This event carries the
 *      information indicating the reason that triggered this detection. The
 *      attributes for this command are defined in
 *      enum qca_wlan_vendor_attr_hang.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG: Get the current values
 *      of spectral parameters used. The spectral scan parameters are specified
 *      by enum qca_wlan_vendor_attr_spectral_scan.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS: Get the debug stats
 *      for spectral scan functionality. The debug stats are specified by
 *      enum qca_wlan_vendor_attr_spectral_diag_stats.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO: Get spectral
 *      scan system capabilities. The capabilities are specified
 *      by enum qca_wlan_vendor_attr_spectral_cap.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS: Get the current
 *      status of spectral scan. The status values are specified
 *      by enum qca_wlan_vendor_attr_spectral_scan_status.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING: Sub-command to flush
 *      peer pending packets. Specify the peer MAC address in
 *      QCA_WLAN_VENDOR_ATTR_PEER_ADDR and the access category of the packets
 *      in QCA_WLAN_VENDOR_ATTR_AC. The attributes are listed
 *      in enum qca_wlan_vendor_attr_flush_pending.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO: Get vendor specific Representative
 *      RF Operating Parameter (RROP) information. The attributes for this
 *      information are defined in enum qca_wlan_vendor_attr_rrop_info. This is
 *      intended for use by external Auto Channel Selection applications.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS: Get the Specific Absorption Rate
 *      (SAR) power limits. This is a companion to the command
 *      @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS and is used to retrieve the
 *      settings currently in use. The attributes returned by this command are
 *      defined by enum qca_vendor_attr_sar_limits.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO: Provides the current behavior of
 *      the WLAN hardware MAC. Also, provides the WLAN netdev interface
 *      information attached to the respective MAC.
 *      This works both as a query (user space asks the current mode) or event
 *      interface (driver advertising the current mode to the user space).
 *      Driver does not trigger this event for temporary hardware mode changes.
 *      Mode changes w.r.t Wi-Fi connection update (VIZ creation / deletion,
 *      channel change, etc.) are updated with this event. Attributes for this
 *      interface are defined in enum qca_wlan_vendor_attr_mac.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH: Set MSDU queue depth threshold
 *      per peer per TID. Attributes for this command are define in
 *      enum qca_wlan_set_qdepth_thresh_attr.
 * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD: Provides the thermal shutdown action
 *      guide for WLAN driver. Request to suspend of driver and FW if the
 *      temperature is higher than the suspend threshold; resume action is
 *      requested to driver if the temperature is lower than the resume
 *      threshold. In user poll mode, request temperature data by user. For test
 *      purpose, getting thermal shutdown configuration parameters is needed.
 *      Attributes for this interface are defined in
 *      enum qca_wlan_vendor_attr_thermal_cmd.
 * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT: Thermal events reported from
 *      driver. Thermal temperature and indication of resume completion are
 *      reported as thermal events. The attributes for this command are defined
 *      in enum qca_wlan_vendor_attr_thermal_event.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION: Sub command to set WiFi
 *      test configuration. Attributes for this command are defined in
 *      enum qca_wlan_vendor_attr_wifi_test_config.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER: This command is used to configure an
 *      RX filter to receive frames from stations that are active on the
 *      operating channel, but not associated with the local device (e.g., STAs
 *      associated with other APs). Filtering is done based on a list of BSSIDs
 *      and STA MAC addresses added by the user. This command is also used to
 *      fetch the statistics of unassociated stations. The attributes used with
 *      this command are defined in enum qca_wlan_vendor_attr_bss_filter.
 *
 * @QCA_NL80211_VENDOR_SUBCMD_NAN_EXT: An extendable version of NAN vendor
 *      command. The earlier command for NAN, QCA_NL80211_VENDOR_SUBCMD_NAN,
 *      carried a payload which was a binary blob of data. The command was not
 *      extendable to send more information. The newer version carries the
 *      legacy blob encapsulated within an attribute and can be extended with
 *      additional vendor attributes that can enhance the NAN command interface.
 */
enum qca_nl80211_vendor_subcmds {
        QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0,
        QCA_NL80211_VENDOR_SUBCMD_TEST = 1,
        /* subcmds 2..8 not yet allocated */
        QCA_NL80211_VENDOR_SUBCMD_ROAMING = 9,
        QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY = 10,
        QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY =  11,
        QCA_NL80211_VENDOR_SUBCMD_NAN =  12,
        QCA_NL80211_VENDOR_SUBCMD_STATS_EXT = 13,
        QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET = 14,
        QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET = 15,
        QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR = 16,
        QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS = 17,
        QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS = 18,
        QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS = 19,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_START = 20,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_STOP = 21,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS = 22,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CAPABILITIES = 23,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS = 24,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE = 25,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT = 26,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT = 27,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND = 28,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_BSSID_HOTLIST = 29,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_BSSID_HOTLIST = 30,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE = 31,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SIGNIFICANT_CHANGE = 32,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SIGNIFICANT_CHANGE = 33,
        QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE = 34,
        QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE = 35,
        QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS = 36,
        QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE = 37,
        QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES = 38,
        QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI = 39,
        QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG = 40,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_LOST = 41,
        QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX = 42,
        /* 43..49 - reserved for QCA */
        QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY = 50,
        QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH = 51,
        QCA_NL80211_VENDOR_SUBCMD_APFIND = 52,
        /* 53 - reserved - was used by QCA, but not in use anymore */
        QCA_NL80211_VENDOR_SUBCMD_DO_ACS = 54,
        QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES = 55,
        QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED = 56,
        QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED = 57,
        QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED = 58,
        QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED = 59,
        QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED = 60,
        QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO = 61,
        QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START = 62,
        QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP = 63,
        QCA_NL80211_VENDOR_SUBCMD_ROAM = 64,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST = 65,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SSID_HOTLIST = 66,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_FOUND = 67,
        QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_LOST = 68,
        QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST = 69,
        QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST = 70,
        QCA_NL80211_VENDOR_SUBCMD_PNO_RESET_PASSPOINT_LIST = 71,
        QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND = 72,
        QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND = 73,
        /* Wi-Fi configuration subcommands */
        QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION = 74,
        QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION = 75,
        QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET = 76,
        QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA = 77,
        QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES = 78,
        QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS = 79,
        QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI = 80,
        QCA_NL80211_VENDOR_SUBCMD_NDP = 81,
        QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD = 82,
        QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER = 83,
        QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE = 84,
        QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS = 85,
        /* 86-90 - reserved for QCA */
        QCA_NL80211_VENDOR_SUBCMD_DATA_OFFLOAD = 91,
        QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG = 92,
        QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME = 93,
        QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT = 94,
        QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT = 95,
        QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER = 96,
        QCA_NL80211_VENDOR_SUBCMD_DCC_GET_STATS = 97,
        QCA_NL80211_VENDOR_SUBCMD_DCC_CLEAR_STATS = 98,
        QCA_NL80211_VENDOR_SUBCMD_DCC_UPDATE_NDL = 99,
        QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT = 100,
        QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES = 101,
        QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG = 102,
        QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST = 103,
        QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL = 104,
        QCA_NL80211_VENDOR_SUBCMD_SETBAND = 105,
        QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN = 106,
        QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE = 107,
        QCA_NL80211_VENDOR_SUBCMD_OTA_TEST = 108,
        QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE = 109,
        /* 110..114 - reserved for QCA */
        QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB = 115,
        /* 116..117 - reserved for QCA */
        QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG = 118,
        QCA_NL80211_VENDOR_SUBCMD_TSF = 119,
        QCA_NL80211_VENDOR_SUBCMD_WISA = 120,
        /* 121 - reserved for QCA */
        QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START = 122,
        QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123,
        QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124,
        QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND = 125,
        QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY = 126,
        QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT = 127,
        /* FTM/indoor location subcommands */
        QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA = 128,
        QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION = 129,
        QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION = 130,
        QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT = 131,
        QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE = 132,
        QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER = 133,
        QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS = 134,
        QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS = 135,
        QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT = 136,
        QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST = 137,
        QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI = 138,
        /* DMG low level RF sector operations */
        QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG = 139,
        QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG = 140,
        QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR = 141,
        QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR = 142,
        QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS = 143,
        QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES = 144,
        QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN = 145,
        QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS = 146,
        QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS = 147,
        QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE = 148,
        QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET = 149,
        QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET = 150,
        QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS = 151,
        QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL = 152,
        QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT = 153,
        QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START = 154,
        QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP = 155,
        QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS = 156,
        QCA_NL80211_VENDOR_SUBCMD_HANG = 157,
        QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG = 158,
        QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS = 159,
        QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO = 160,
        QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS = 161,
        /* Flush peer pending data */
        QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING = 162,
        QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO = 163,
        QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS = 164,
        QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO = 165,
        QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH = 166,
        /* Thermal shutdown commands to protect wifi chip */
        QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD = 167,
        QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT = 168,
        /* Wi-Fi test configuration subcommand */
        QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION = 169,
        /* Frame filter operations for other BSSs/unassociated STAs */
        QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER = 170,
        QCA_NL80211_VENDOR_SUBCMD_NAN_EXT = 171,
};

enum qca_wlan_vendor_attr {
        QCA_WLAN_VENDOR_ATTR_INVALID = 0,
        /* used by QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY */
        QCA_WLAN_VENDOR_ATTR_DFS     = 1,
        /* Used only when driver sends vendor events to the userspace under the
         * command QCA_NL80211_VENDOR_SUBCMD_NAN. Not used when userspace sends
         * commands to the driver.
         */
        QCA_WLAN_VENDOR_ATTR_NAN     = 2,
        /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */
        QCA_WLAN_VENDOR_ATTR_STATS_EXT     = 3,
        /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */
        QCA_WLAN_VENDOR_ATTR_IFINDEX     = 4,
        /* used by QCA_NL80211_VENDOR_SUBCMD_ROAMING, u32 with values defined
         * by enum qca_roaming_policy.
         */
        QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY = 5,
        QCA_WLAN_VENDOR_ATTR_MAC_ADDR = 6,
        /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */
        QCA_WLAN_VENDOR_ATTR_FEATURE_FLAGS = 7,
        QCA_WLAN_VENDOR_ATTR_TEST = 8,
        /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */
        /* Unsigned 32-bit value. */
        QCA_WLAN_VENDOR_ATTR_CONCURRENCY_CAPA = 9,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_2_4_BAND = 10,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_5_0_BAND = 11,
        /* Unsigned 32-bit value from enum qca_set_band. */
        QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE = 12,
        /* Dummy (NOP) attribute for 64 bit padding */
        QCA_WLAN_VENDOR_ATTR_PAD = 13,
        /* Unique FTM session cookie (Unsigned 64 bit). Specified in
         * QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION. Reported in
         * the session in QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT and
         * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE.
         */
        QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE = 14,
        /* Indoor location capabilities, returned by
         * QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA.
         * see enum qca_wlan_vendor_attr_loc_capa.
         */
        QCA_WLAN_VENDOR_ATTR_LOC_CAPA = 15,
        /* Array of nested attributes containing information about each peer
         * in FTM measurement session. See enum qca_wlan_vendor_attr_peer_info
         * for supported attributes for each peer.
         */
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS = 16,
        /* Array of nested attributes containing measurement results for
         * one or more peers, reported by the
         * QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT event.
         * See enum qca_wlan_vendor_attr_peer_result for list of supported
         * attributes.
         */
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS = 17,
        /* Flag attribute for enabling or disabling responder functionality. */
        QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE = 18,
        /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
         * command to specify the LCI report that will be sent by
         * the responder during a measurement exchange. The format is
         * defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.10.
         */
        QCA_WLAN_VENDOR_ATTR_FTM_LCI = 19,
        /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
         * command to specify the location civic report that will
         * be sent by the responder during a measurement exchange.
         * The format is defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.13.
         */
        QCA_WLAN_VENDOR_ATTR_FTM_LCR = 20,
        /* Session/measurement completion status code,
         * reported in QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE and
         * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT
         * see enum qca_vendor_attr_loc_session_status.
         */
        QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS = 21,
        /* Initial dialog token used by responder (0 if not specified),
         * unsigned 8 bit value.
         */
        QCA_WLAN_VENDOR_ATTR_FTM_INITIAL_TOKEN = 22,
        /* AOA measurement type. Requested in QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS
         * and optionally in QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION if
         * AOA measurements are needed as part of an FTM session.
         * Reported by QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT. See
         * enum qca_wlan_vendor_attr_aoa_type.
         */
        QCA_WLAN_VENDOR_ATTR_AOA_TYPE = 23,
        /* A bit mask (unsigned 32 bit value) of antenna arrays used
         * by indoor location measurements. Refers to the antenna
         * arrays described by QCA_VENDOR_ATTR_LOC_CAPA_ANTENNA_ARRAYS.
         */
        QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK = 24,
        /* AOA measurement data. Its contents depends on the AOA measurement
         * type and antenna array mask:
         * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: array of U16 values,
         * phase of the strongest CIR path for each antenna in the measured
         * array(s).
         * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: array of 2 U16
         * values, phase and amplitude of the strongest CIR path for each
         * antenna in the measured array(s).
         */
        QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT = 25,
        /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command
         * to specify the chain number (unsigned 32 bit value) to inquire
         * the corresponding antenna RSSI value
         */
        QCA_WLAN_VENDOR_ATTR_CHAIN_INDEX = 26,
        /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command
         * to report the specific antenna RSSI value (unsigned 32 bit value)
         */
        QCA_WLAN_VENDOR_ATTR_CHAIN_RSSI = 27,
        /* Frequency in MHz, various uses. Unsigned 32 bit value */
        QCA_WLAN_VENDOR_ATTR_FREQ = 28,
        /* TSF timer value, unsigned 64 bit value.
         * May be returned by various commands.
         */
        QCA_WLAN_VENDOR_ATTR_TSF = 29,
        /* DMG RF sector index, unsigned 16 bit number. Valid values are
         * 0..127 for sector indices or 65535 as special value used to
         * unlock sector selection in
         * QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR.
         */
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX = 30,
        /* DMG RF sector type, unsigned 8 bit value. One of the values
         * in enum qca_wlan_vendor_attr_dmg_rf_sector_type.
         */
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE = 31,
        /* Bitmask of DMG RF modules for which information is requested. Each
         * bit corresponds to an RF module with the same index as the bit
         * number. Unsigned 32 bit number but only low 8 bits can be set since
         * all DMG chips currently have up to 8 RF modules.
         */
        QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK = 32,
        /* Array of nested attributes where each entry is DMG RF sector
         * configuration for a single RF module.
         * Attributes for each entry are taken from enum
         * qca_wlan_vendor_attr_dmg_rf_sector_cfg.
         * Specified in QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG
         * and returned by QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG.
         */
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG = 33,
        /* Used in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command
         * to report frame aggregation statistics to userspace.
         */
        QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_NUM = 34,
        QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_INFO = 35,
        /* Unsigned 8-bit value representing MBO transition reason code as
         * provided by the AP used by subcommand
         * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS. This is
         * specified by the userspace in the request to the driver.
         */
        QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON = 36,
        /* Array of nested attributes, BSSID and status code, used by subcommand
         * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS, where each
         * entry is taken from enum qca_wlan_vendor_attr_btm_candidate_info.
         * The userspace space specifies the list/array of candidate BSSIDs in
         * the order of preference in the request. The driver specifies the
         * status code, for each BSSID in the list, in the response. The
         * acceptable candidates are listed in the order preferred by the
         * driver.
         */
        QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO = 37,
        /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command
         * See enum qca_wlan_vendor_attr_brp_ant_limit_mode.
         */
        QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE = 38,
        /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command
         * to define the number of antennas to use for BRP.
         * different purpose in each ANT_LIMIT_MODE:
         * DISABLE - ignored
         * EFFECTIVE - upper limit to number of antennas to be used
         * FORCE - exact number of antennas to be used
         * unsigned 8 bit value
         */
        QCA_WLAN_VENDOR_ATTR_BRP_ANT_NUM_LIMIT = 39,
        /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command
         * to report the corresponding antenna index to the chain RSSI value
         */
        QCA_WLAN_VENDOR_ATTR_ANTENNA_INFO = 40,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_MAX        = QCA_WLAN_VENDOR_ATTR_AFTER_LAST - 1,
};

enum qca_roaming_policy {
        QCA_ROAMING_NOT_ALLOWED,
        QCA_ROAMING_ALLOWED_WITHIN_ESS,
};

enum qca_wlan_vendor_attr_roam_auth {
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID,
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE,
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE,
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED,
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR,
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK,
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK,
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS,
        /* Indicates the status of re-association requested by user space for
         * the BSSID specified by QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID.
         * Type u16.
         * Represents the status code from AP. Use
         * %WLAN_STATUS_UNSPECIFIED_FAILURE if the device cannot give you the
         * real status code for failures.
         */
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS,
        /* This attribute indicates that the old association was maintained when
         * a re-association is requested by user space and that re-association
         * attempt fails (i.e., cannot connect to the requested BSS, but can
         * remain associated with the BSS with which the association was in
         * place when being requested to roam). Used along with
         * WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS to indicate the current
         * re-association status. Type flag.
         * This attribute is applicable only for re-association failure cases.
         */
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION,
        /* This attribute specifies the PMK if one was newly generated during
         * FILS roaming. This is added to the PMKSA cache and is used in
         * subsequent connections with PMKSA caching.
         */
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK = 11,
        /* This attribute specifies the PMKID used/generated for the current
         * FILS roam. This is used in subsequent connections with PMKSA caching.
         */
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID = 12,
        /* A 16-bit unsigned value specifying the next sequence number to use
         * in ERP message in the currently associated realm. This is used in
         * doing subsequent ERP based connections in the same realm.
         */
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM = 13,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MAX =
        QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST - 1
};

enum qca_wlan_vendor_attr_p2p_listen_offload {
        QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID = 0,
        /* A 32-bit unsigned value; the P2P listen frequency (MHz); must be one
         * of the social channels.
         */
        QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL,
        /* A 32-bit unsigned value; the P2P listen offload period (ms).
         */
        QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD,
        /* A 32-bit unsigned value; the P2P listen interval duration (ms).
         */
        QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL,
        /* A 32-bit unsigned value; number of interval times the firmware needs
         * to run the offloaded P2P listen operation before it stops.
         */
        QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT,
        /* An array of arbitrary binary data with one or more 8-byte values.
         * The device types include both primary and secondary device types.
         */
        QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES,
        /* An array of unsigned 8-bit characters; vendor information elements.
         */
        QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE,
        /* A 32-bit unsigned value; a control flag to indicate whether listen
         * results need to be flushed to wpa_supplicant.
         */
        QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG,
        /* A 8-bit unsigned value; reason code for P2P listen offload stop
         * event.
         */
        QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX =
        QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST - 1
};

enum qca_wlan_vendor_attr_acs_offload {
        QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL,
        QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL,
        QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE,
        QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED,
        QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED,
        QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED,
        QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH,
        QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST,
        QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL,
        QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL,
        QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_ACS_MAX =
        QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST - 1
};

enum qca_wlan_vendor_acs_hw_mode {
        QCA_ACS_MODE_IEEE80211B,
        QCA_ACS_MODE_IEEE80211G,
        QCA_ACS_MODE_IEEE80211A,
        QCA_ACS_MODE_IEEE80211AD,
        QCA_ACS_MODE_IEEE80211ANY,
};

/**
 * enum qca_wlan_vendor_features - Vendor device/driver feature flags
 *
 * @QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD: Device supports key
 *      management offload, a mechanism where the station's firmware
 *      does the exchange with the AP to establish the temporal keys
 *      after roaming, rather than having the user space wpa_supplicant do it.
 * @QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY: Device supports automatic
 *      band selection based on channel selection results.
 * @QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS: Device supports
 *      simultaneous off-channel operations.
 * @QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD: Device supports P2P
 *      Listen offload; a mechanism where the station's firmware takes care of
 *      responding to incoming Probe Request frames received from other P2P
 *      Devices whilst in Listen state, rather than having the user space
 *      wpa_supplicant do it. Information from received P2P requests are
 *      forwarded from firmware to host whenever the host processor wakes up.
 * @QCA_WLAN_VENDOR_FEATURE_OCE_STA: Device supports all OCE non-AP STA
 *      specific features.
 * @QCA_WLAN_VENDOR_FEATURE_OCE_AP: Device supports all OCE AP specific
 *      features.
 * @QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON: Device supports OCE STA-CFON
 *      specific features only. If a Device sets this bit but not the
 *      %QCA_WLAN_VENDOR_FEATURE_OCE_AP, the userspace shall assume that
 *      this Device may not support all OCE AP functionalities but can support
 *      only OCE STA-CFON functionalities.
 * @QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY: Device supports self
 *      managed regulatory.
 * @NUM_QCA_WLAN_VENDOR_FEATURES: Number of assigned feature bits
 */
enum qca_wlan_vendor_features {
        QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD        = 0,
        QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY     = 1,
        QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS = 2,
        QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD      = 3,
        QCA_WLAN_VENDOR_FEATURE_OCE_STA                 = 4,
        QCA_WLAN_VENDOR_FEATURE_OCE_AP                  = 5,
        QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON            = 6,
        QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY = 7,
        NUM_QCA_WLAN_VENDOR_FEATURES /* keep last */
};

/**
 * enum qca_wlan_vendor_attr_data_offload_ind - Vendor Data Offload Indication
 *
 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION: Session corresponding to
 *      the offloaded data.
 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL: Protocol of the offloaded
 *      data.
 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT: Event type for the data offload
 *      indication.
 */
enum qca_wlan_vendor_attr_data_offload_ind {
        QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION,
        QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL,
        QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_MAX =
        QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST - 1
};

/**
 * enum qca_wlan_vendor_attr_ocb_set_config - Vendor subcmd attributes to set
 *      OCB config
 *
 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT: Number of channels in the
 *      configuration
 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE: Size of the schedule
 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY: Array of channels
 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY: Array of channels to be
 *      scheduled
 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY: Array of NDL channel
 *      information
 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY: Array of NDL
 *      active state configuration
 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS: Configuration flags such as
 *      OCB_CONFIG_FLAG_80211_FRAME_MODE
 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM: Default TX parameters to
 *      use in the case that a packet is sent without a TX control header
 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION: Max duration after the
 *      last TA received that the local time set by TA is synchronous to other
 *      communicating OCB STAs.
 */
enum qca_wlan_vendor_attr_ocb_set_config {
        QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT = 1,
        QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE = 2,
        QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY = 3,
        QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY = 4,
        QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY = 5,
        QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY = 6,
        QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS = 7,
        QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM = 8,
        QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION = 9,
        QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_MAX =
        QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST - 1
};

/**
 * enum qca_wlan_vendor_attr_ocb_set_utc_time - Vendor subcmd attributes to set
 *      UTC time
 *
 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE: The UTC time as an array of
 *      10 bytes
 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR: The time error as an array of
 *      5 bytes
 */
enum qca_wlan_vendor_attr_ocb_set_utc_time {
        QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE = 1,
        QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR = 2,
        QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_MAX =
        QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST - 1
};

/**
 * enum qca_wlan_vendor_attr_ocb_start_timing_advert - Vendor subcmd attributes
 *      to start sending timing advert frames
 *
 * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ: Cannel frequency
 *      on which to send the frames
 * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE: Number of times
 *      the frame is sent in 5 seconds
 */
enum qca_wlan_vendor_attr_ocb_start_timing_advert {
        QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ = 1,
        QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE = 2,
        QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_MAX =
        QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST - 1
};

/**
 * enum qca_wlan_vendor_attr_ocb_stop_timing_advert - Vendor subcmd attributes
 *      to stop timing advert
 *
 * @QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ: The channel
 *      frequency on which to stop the timing advert
 */
enum qca_wlan_vendor_attr_ocb_stop_timing_advert {
        QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ = 1,
        QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_MAX =
        QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST - 1
};

/**
 * enum qca_wlan_vendor_attr_ocb_get_tsf_response - Vendor subcmd attributes to
 *      get TSF timer value
 *
 * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH: Higher 32 bits of the
 *      timer
 * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW: Lower 32 bits of the timer
 */
enum qca_wlan_vendor_attr_ocb_get_tsf_resp {
        QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH = 1,
        QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW = 2,
        QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_MAX =
        QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST - 1
};

enum qca_vendor_attr_get_preferred_freq_list {
        QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID,
        /* A 32-unsigned value; the interface type/mode for which the preferred
         * frequency list is requested (see enum qca_iface_type for possible
         * values); used in GET_PREFERRED_FREQ_LIST command from user-space to
         * kernel and in the kernel response back to user-space.
         */
        QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE,
        /* An array of 32-unsigned values; values are frequency (MHz); sent
         * from kernel space to user space.
         */
        QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST,
        /* An array of nested values as per enum qca_wlan_vendor_attr_pcl
         * attribute. Each element contains frequency (MHz), weight, and flag
         * bit mask indicating how the frequency should be used in P2P
         * negotiation; sent from kernel space to user space.
         */
        QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_WEIGHED_PCL,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX =
        QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST - 1
};

enum qca_vendor_attr_probable_oper_channel {
        QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID,
        /* 32-bit unsigned value; indicates the connection/iface type likely to
         * come on this channel (see enum qca_iface_type).
         */
        QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE,
        /* 32-bit unsigned value; the frequency (MHz) of the probable channel */
        QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX =
        QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST - 1
};

enum qca_iface_type {
        QCA_IFACE_TYPE_STA,
        QCA_IFACE_TYPE_AP,
        QCA_IFACE_TYPE_P2P_CLIENT,
        QCA_IFACE_TYPE_P2P_GO,
        QCA_IFACE_TYPE_IBSS,
        QCA_IFACE_TYPE_TDLS,
};

enum qca_set_band {
        QCA_SETBAND_AUTO,
        QCA_SETBAND_5G,
        QCA_SETBAND_2G,
};

/**
 * enum qca_access_policy - Access control policy
 *
 * Access control policy is applied on the configured IE
 * (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE).
 * To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY.
 *
 * @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi connections which match
 *      the specific configuration (IE) set, i.e., allow all the
 *      connections which do not match the configuration.
 * @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi connections which match
 *      the specific configuration (IE) set, i.e., deny all the
 *      connections which do not match the configuration.
 */
enum qca_access_policy {
        QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED,
        QCA_ACCESS_POLICY_DENY_UNLESS_LISTED,
};

/**
 * enum qca_vendor_attr_get_tsf: Vendor attributes for TSF capture
 * @QCA_WLAN_VENDOR_ATTR_TSF_CMD: enum qca_tsf_operation (u32)
 * @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Unsigned 64 bit TSF timer value
 * @QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE: Unsigned 64 bit Synchronized
 *      SOC timer value at TSF capture
 */
enum qca_vendor_attr_tsf_cmd {
        QCA_WLAN_VENDOR_ATTR_TSF_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_TSF_CMD,
        QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE,
        QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE,
        QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_TSF_MAX =
        QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST - 1
};

/**
 * enum qca_tsf_operation: TSF driver commands
 * @QCA_TSF_CAPTURE: Initiate TSF Capture
 * @QCA_TSF_GET: Get TSF capture value
 * @QCA_TSF_SYNC_GET: Initiate TSF capture and return with captured value
 */
enum qca_tsf_cmd {
        QCA_TSF_CAPTURE,
        QCA_TSF_GET,
        QCA_TSF_SYNC_GET,
};

/**
 * enum qca_vendor_attr_wisa_cmd
 * @QCA_WLAN_VENDOR_ATTR_WISA_MODE: WISA mode value (u32)
 * WISA setup vendor commands
 */
enum qca_vendor_attr_wisa_cmd {
        QCA_WLAN_VENDOR_ATTR_WISA_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_WISA_MODE,
        QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_WISA_MAX =
        QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST - 1
};

/* IEEE 802.11 Vendor Specific elements */

/**
 * enum qca_vendor_element_id - QCA Vendor Specific element types
 *
 * These values are used to identify QCA Vendor Specific elements. The
 * payload of the element starts with the three octet OUI (OUI_QCA) and
 * is followed by a single octet type which is defined by this enum.
 *
 * @QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST: P2P preferred channel list.
 *      This element can be used to specify preference order for supported
 *      channels. The channels in this list are in preference order (the first
 *      one has the highest preference) and are described as a pair of
 *      (global) Operating Class and Channel Number (each one octet) fields.
 *
 *      This extends the standard P2P functionality by providing option to have
 *      more than one preferred operating channel. When this element is present,
 *      it replaces the preference indicated in the Operating Channel attribute.
 *      For supporting other implementations, the Operating Channel attribute is
 *      expected to be used with the highest preference channel. Similarly, all
 *      the channels included in this Preferred channel list element are
 *      expected to be included in the Channel List attribute.
 *
 *      This vendor element may be included in GO Negotiation Request, P2P
 *      Invitation Request, and Provision Discovery Request frames.
 *
 * @QCA_VENDOR_ELEM_HE_CAPAB: HE Capabilities element.
 *      This element can be used for pre-standard publication testing of HE
 *      before P802.11ax draft assigns the element ID. The payload of this
 *      vendor specific element is defined by the latest P802.11ax draft.
 *      Please note that the draft is still work in progress and this element
 *      payload is subject to change.
 *
 * @QCA_VENDOR_ELEM_HE_OPER: HE Operation element.
 *      This element can be used for pre-standard publication testing of HE
 *      before P802.11ax draft assigns the element ID. The payload of this
 *      vendor specific element is defined by the latest P802.11ax draft.
 *      Please note that the draft is still work in progress and this element
 *      payload is subject to change.
 *
 * @QCA_VENDOR_ELEM_RAPS: RAPS element (OFDMA-based Random Access Parameter Set
 *      element).
 *      This element can be used for pre-standard publication testing of HE
 *      before P802.11ax draft assigns the element ID extension. The payload of
 *      this vendor specific element is defined by the latest P802.11ax draft
 *      (not including the Element ID Extension field). Please note that the
 *      draft is still work in progress and this element payload is subject to
 *      change.
 *
 * @QCA_VENDOR_ELEM_MU_EDCA_PARAMS: MU EDCA Parameter Set element.
 *      This element can be used for pre-standard publication testing of HE
 *      before P802.11ax draft assigns the element ID extension. The payload of
 *      this vendor specific element is defined by the latest P802.11ax draft
 *      (not including the Element ID Extension field). Please note that the
 *      draft is still work in progress and this element payload is subject to
 *      change.
 *
 * @QCA_VENDOR_ELEM_BSS_COLOR_CHANGE: BSS Color Change Announcement element.
 *      This element can be used for pre-standard publication testing of HE
 *      before P802.11ax draft assigns the element ID extension. The payload of
 *      this vendor specific element is defined by the latest P802.11ax draft
 *      (not including the Element ID Extension field). Please note that the
 *      draft is still work in progress and this element payload is subject to
 *      change.
 */
enum qca_vendor_element_id {
        QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0,
        QCA_VENDOR_ELEM_HE_CAPAB = 1,
        QCA_VENDOR_ELEM_HE_OPER = 2,
        QCA_VENDOR_ELEM_RAPS = 3,
        QCA_VENDOR_ELEM_MU_EDCA_PARAMS = 4,
        QCA_VENDOR_ELEM_BSS_COLOR_CHANGE = 5,
};

/**
 * enum qca_wlan_vendor_attr_scan - Specifies vendor scan attributes
 *
 * @QCA_WLAN_VENDOR_ATTR_SCAN_IE: IEs that should be included as part of scan
 * @QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES: Nested unsigned 32-bit attributes
 *      with frequencies to be scanned (in MHz)
 * @QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS: Nested attribute with SSIDs to be scanned
 * @QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES: Nested array attribute of supported
 *      rates to be included
 * @QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE: flag used to send probe requests
 *      at non CCK rate in 2GHz band
 * @QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS: Unsigned 32-bit scan flags
 * @QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE: Unsigned 64-bit cookie provided by the
 *      driver for the specific scan request
 * @QCA_WLAN_VENDOR_ATTR_SCAN_STATUS: Unsigned 8-bit status of the scan
 *      request decoded as in enum scan_status
 * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC: 6-byte MAC address to use when randomisation
 *      scan flag is set
 * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with
 *      randomisation
 * @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: 6-byte MAC address representing the
 *      specific BSSID to scan for.
 */
enum qca_wlan_vendor_attr_scan {
        QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0,
        QCA_WLAN_VENDOR_ATTR_SCAN_IE = 1,
        QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES = 2,
        QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS = 3,
        QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES = 4,
        QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE = 5,
        QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS = 6,
        QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE = 7,
        QCA_WLAN_VENDOR_ATTR_SCAN_STATUS = 8,
        QCA_WLAN_VENDOR_ATTR_SCAN_MAC = 9,
        QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK = 10,
        QCA_WLAN_VENDOR_ATTR_SCAN_BSSID = 11,
        QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_SCAN_MAX =
        QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1
};

/**
 * enum scan_status - Specifies the valid values the vendor scan attribute
 *      QCA_WLAN_VENDOR_ATTR_SCAN_STATUS can take
 *
 * @VENDOR_SCAN_STATUS_NEW_RESULTS: implies the vendor scan is successful with
 *      new scan results
 * @VENDOR_SCAN_STATUS_ABORTED: implies the vendor scan was aborted in-between
 */
enum scan_status {
        VENDOR_SCAN_STATUS_NEW_RESULTS,
        VENDOR_SCAN_STATUS_ABORTED,
        VENDOR_SCAN_STATUS_MAX,
};

/**
 * enum qca_vendor_attr_ota_test - Specifies the values for vendor
 *                       command QCA_NL80211_VENDOR_SUBCMD_OTA_TEST
 * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE: enable ota test
 */
enum qca_vendor_attr_ota_test {
        QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID,
        /* 8-bit unsigned value to indicate if OTA test is enabled */
        QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX =
        QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST - 1
};

/**
 * enum qca_vendor_attr_txpower_scale - vendor sub commands index
 *
 * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE: scaling value
 */
enum qca_vendor_attr_txpower_scale {
        QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID,
        /* 8-bit unsigned value to indicate the scaling of tx power */
        QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX =
        QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST - 1
};

/**
 * enum qca_vendor_attr_txpower_decr_db - Attributes for TX power decrease
 *
 * These attributes are used with QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB.
 */
enum qca_vendor_attr_txpower_decr_db {
        QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_INVALID,
        /* 8-bit unsigned value to indicate the reduction of TX power in dB for
         * a virtual interface.
         */
        QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_MAX =
        QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST - 1
};

/* Attributes for data used by
 * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
 * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands.
 */
enum qca_wlan_vendor_attr_config {
        QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID = 0,
        /* Unsigned 32-bit value to set the DTIM period.
         * Whether the wifi chipset wakes at every dtim beacon or a multiple of
         * the DTIM period. If DTIM is set to 3, the STA shall wake up every 3
         * DTIM beacons.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM = 1,
        /* Unsigned 32-bit value to set the wifi_iface stats averaging factor
         * used to calculate statistics like average the TSF offset or average
         * number of frame leaked.
         * For instance, upon Beacon frame reception:
         * current_avg = ((beacon_TSF - TBTT) * factor + previous_avg * (0x10000 - factor) ) / 0x10000
         * For instance, when evaluating leaky APs:
         * current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR = 2,
        /* Unsigned 32-bit value to configure guard time, i.e., when
         * implementing IEEE power management based on frame control PM bit, how
         * long the driver waits before shutting down the radio and after
         * receiving an ACK frame for a Data frame with PM bit set.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME = 3,
        /* Unsigned 32-bit value to change the FTM capability dynamically */
        QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT = 4,
        /* Unsigned 16-bit value to configure maximum TX rate dynamically */
        QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE = 5,
        /* Unsigned 32-bit value to configure the number of continuous
         * Beacon Miss which shall be used by the firmware to penalize
         * the RSSI.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS = 6,
        /* Unsigned 8-bit value to configure the channel avoidance indication
         * behavior. Firmware to send only one indication and ignore duplicate
         * indications when set to avoid multiple Apps wakeups.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND = 7,
        /* 8-bit unsigned value to configure the maximum TX MPDU for
         * aggregation.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION = 8,
        /* 8-bit unsigned value to configure the maximum RX MPDU for
         * aggregation.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION = 9,
        /* 8-bit unsigned value to configure the Non aggregrate/11g sw
         * retry threshold (0 disable, 31 max).
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY = 10,
        /* 8-bit unsigned value to configure the aggregrate sw
         * retry threshold (0 disable, 31 max).
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY = 11,
        /* 8-bit unsigned value to configure the MGMT frame
         * retry threshold (0 disable, 31 max).
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY = 12,
        /* 8-bit unsigned value to configure the CTRL frame
         * retry threshold (0 disable, 31 max).
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY = 13,
        /* 8-bit unsigned value to configure the propagation delay for
         * 2G/5G band (0~63, units in us)
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY = 14,
        /* Unsigned 32-bit value to configure the number of unicast TX fail
         * packet count. The peer is disconnected once this threshold is
         * reached.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT = 15,
        /* Attribute used to set scan default IEs to the driver.
         *
         * These IEs can be used by scan operations that will be initiated by
         * the driver/firmware.
         *
         * For further scan requests coming to the driver, these IEs should be
         * merged with the IEs received along with scan request coming to the
         * driver. If a particular IE is present in the scan default IEs but not
         * present in the scan request, then that IE should be added to the IEs
         * sent in the Probe Request frames for that scan request.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES = 16,
        /* Unsigned 32-bit attribute for generic commands */
        QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND = 17,
        /* Unsigned 32-bit value attribute for generic commands */
        QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE = 18,
        /* Unsigned 32-bit data attribute for generic command response */
        QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA = 19,
        /* Unsigned 32-bit length attribute for
         * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH = 20,
        /* Unsigned 32-bit flags attribute for
         * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS = 21,
        /* Unsigned 32-bit, defining the access policy.
         * See enum qca_access_policy. Used with
         * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY = 22,
        /* Sets the list of full set of IEs for which a specific access policy
         * has to be applied. Used along with
         * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access.
         * Zero length payload can be used to clear this access constraint.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST = 23,
        /* Unsigned 32-bit, specifies the interface index (netdev) for which the
         * corresponding configurations are applied. If the interface index is
         * not specified, the configurations are attributed to the respective
         * wiphy.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX = 24,
        /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */
        QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER = 25,
        /* 8-bit unsigned value to configure the driver and below layers to
         * ignore the assoc disallowed set by APs while connecting
         * 1-Ignore, 0-Don't ignore
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED = 26,
        /* 32-bit unsigned value to trigger antenna diversity features:
         * 1-Enable, 0-Disable
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA = 27,
        /* 32-bit unsigned value to configure specific chain antenna */
        QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN = 28,
        /* 32-bit unsigned value to trigger cycle selftest
         * 1-Enable, 0-Disable
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST = 29,
        /* 32-bit unsigned to configure the cycle time of selftest
         * the unit is micro-second
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL = 30,
        /* 32-bit unsigned value to set reorder timeout for AC_VO */
        QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VOICE = 31,
        /* 32-bit unsigned value to set reorder timeout for AC_VI */
        QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VIDEO = 32,
        /* 32-bit unsigned value to set reorder timeout for AC_BE */
        QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BESTEFFORT = 33,
        /* 32-bit unsigned value to set reorder timeout for AC_BK */
        QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BACKGROUND = 34,
        /* 6-byte MAC address to point out the specific peer */
        QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC = 35,
        /* 32-bit unsigned value to set window size for specific peer */
        QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_WINLIMIT = 36,
        /* 8-bit unsigned value to set the beacon miss threshold in 2.4 GHz */
        QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_24 = 37,
        /* 8-bit unsigned value to set the beacon miss threshold in 5 GHz */
        QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_5 = 38,
        /* 32-bit unsigned value to configure 5 or 10 MHz channel width for
         * station device while in disconnect state. The attribute use the
         * value of enum nl80211_chan_width: NL80211_CHAN_WIDTH_5 means 5 MHz,
         * NL80211_CHAN_WIDTH_10 means 10 MHz. If set, the device work in 5 or
         * 10 MHz channel width, the station will not connect to a BSS using 20
         * MHz or higher bandwidth. Set to NL80211_CHAN_WIDTH_20_NOHT to
         * clear this constraint.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH = 39,
        /* 32-bit unsigned value to configure the propagation absolute delay
         * for 2G/5G band (units in us)
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY = 40,
        /* 32-bit unsigned value to set probe period */
        QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_PERIOD = 41,
        /* 32-bit unsigned value to set stay period */
        QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_STAY_PERIOD = 42,
        /* 32-bit unsigned value to set snr diff */
        QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SNR_DIFF = 43,
        /* 32-bit unsigned value to set probe dwell time */
        QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_DWELL_TIME = 44,
        /* 32-bit unsigned value to set mgmt snr weight */
        QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_MGMT_SNR_WEIGHT = 45,
        /* 32-bit unsigned value to set data snr weight */
        QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_DATA_SNR_WEIGHT = 46,
        /* 32-bit unsigned value to set ack snr weight */
        QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ACK_SNR_WEIGHT = 47,
        /* 32-bit unsigned value to configure the listen interval.
         * This is in units of beacon intervals. This configuration alters
         * the negotiated listen interval with the AP during the connection.
         * It is highly recommended to configure a value less than or equal to
         * the one negotiated during the association. Configuring any greater
         * value can have adverse effects (frame loss, AP disassociating STA,
         * etc.).
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL = 48,
        /*
         * 8 bit unsigned value that is set on an AP/GO virtual interface to
         * disable operations that would cause the AP/GO to leave its operating
         * channel.
         *
         * This will restrict the scans to the AP/GO operating channel and the
         * channels of the other band, if DBS is supported.A STA/CLI interface
         * brought up after this setting is enabled, will be restricted to
         * connecting to devices only on the AP/GO interface's operating channel
         * or on the other band in DBS case. P2P supported channel list is
         * modified, to only include AP interface's operating-channel and the
         * channels of the other band if DBS is supported.
         *
         * These restrictions are only applicable as long as the AP/GO interface
         * is alive. If the AP/GO interface is brought down then this
         * setting/restriction is forgotten.
         *
         * If this variable is set on an AP/GO interface while a multi-channel
         * concurrent session is active, it has no effect on the operation of
         * the current interfaces, other than restricting the scan to the AP/GO
         * operating channel and the other band channels if DBS is supported.
         * However, if the STA is brought down and restarted then the new STA
         * connection will either be formed on the AP/GO channel or on the
         * other band in a DBS case. This is because of the scan being
         * restricted on these channels as mentioned above.
         *
         * 1-Restrict / 0-Don't restrict offchannel operations.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL = 49,
        /*
         * 8 bit unsigned value to enable/disable LRO (Large Receive Offload)
         * on an interface.
         * 1 - Enable, 0 - Disable.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_LRO = 50,

        /*
         * 8 bit unsigned value to globally enable/disable scan
         * 1 - Enable, 0 - Disable.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_ENABLE = 51,

        /* 8-bit unsigned value to set the total beacon miss count
         * This parameter will set the total beacon miss count.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_TOTAL_BEACON_MISS_COUNT = 52,

        /* Unsigned 32-bit value to configure the number of continuous
         * Beacon Miss which shall be used by the firmware to penalize
         * the RSSI for BTC.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS_BTC = 53,

        /* 8-bit unsigned value to configure the driver and below layers to
         * enable/disable all FILS features.
         * 0-enable, 1-disable
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_FILS = 54,

        /* 16-bit unsigned value to configure the level of WLAN latency
         * module. See enum qca_wlan_vendor_attr_config_latency_level.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL = 55,

        /* 8-bit unsigned value indicating the driver to use the RSNE as-is from
         * the connect interface. Exclusively used for the scenarios where the
         * device is used as a test bed device with special functionality and
         * not recommended for production. This helps driver to not validate the
         * RSNE passed from user space and thus allow arbitrary IE data to be
         * used for testing purposes.
         * 1-enable, 0-disable.
         * Applications set/reset this configuration. If not reset, this
         * parameter remains in use until the driver is unloaded.
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_RSN_IE = 56,

        /* 8-bit unsigned value to trigger green Tx power saving.
         * 1-Enable, 0-Disable
         */
        QCA_WLAN_VENDOR_ATTR_CONFIG_GTX = 57,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_CONFIG_MAX =
        QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_sap_config - Parameters for AP configuration
 */
enum qca_wlan_vendor_attr_sap_config {
        QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID = 0,
        /* 1 - reserved for QCA */
        /* List of frequencies on which AP is expected to operate.
         * This is irrespective of ACS configuration. This list is a priority
         * based one and is looked for before the AP is created to ensure the
         * best concurrency sessions (avoid MCC and use DBS/SCC) co-exist in
         * the system.
         */
        QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST = 2,

        QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX =
        QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for AP
 *                                      conditional channel switch
 */
enum qca_wlan_vendor_attr_sap_conditional_chan_switch {
        QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0,
        /* Priority based frequency list (an array of u32 values in host byte
         * order)
         */
        QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1,
        /* Status of the conditional switch (u32).
         * 0: Success, Non-zero: Failure
         */
        QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2,

        QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX =
        QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_gpio_attr - Parameters for GPIO configuration
 */
enum qca_wlan_gpio_attr {
        QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0,
        /* Unsigned 32-bit attribute for GPIO command */
        QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND,
        /* Unsigned 32-bit attribute for GPIO PIN number to configure */
        QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM,
        /* Unsigned 32-bit attribute for GPIO value to configure */
        QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE,
        /* Unsigned 32-bit attribute for GPIO pull type */
        QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE,
        /* Unsigned 32-bit attribute for GPIO interrupt mode */
        QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST,
        QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX =
        QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1
};

/**
 * qca_wlan_set_qdepth_thresh_attr - Parameters for setting
 * MSDUQ depth threshold per peer per tid in the target
 *
 * Associated Vendor Command:
 * QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH
 */
enum qca_wlan_set_qdepth_thresh_attr {
        QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_INVALID = 0,
        /* 6-byte MAC address */
        QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAC_ADDR,
        /* Unsigned 32-bit attribute for holding the TID */
        QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_TID,
        /* Unsigned 32-bit attribute for holding the update mask
         * bit 0 - Update high priority msdu qdepth threshold
         * bit 1 - Update low priority msdu qdepth threshold
         * bit 2 - Update UDP msdu qdepth threshold
         * bit 3 - Update Non UDP msdu qdepth threshold
         * rest of bits are reserved
         */
        QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_UPDATE_MASK,
        /* Unsigned 32-bit attribute for holding the threshold value */
        QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_VALUE,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST,
        QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAX =
                QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability
 */
enum qca_wlan_vendor_attr_get_hw_capability {
        QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID,
        /* Antenna isolation
         * An attribute used in the response.
         * The content of this attribute is encoded in a byte array. Each byte
         * value is an antenna isolation value. The array length is the number
         * of antennas.
         */
        QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION,
        /* Request HW capability
         * An attribute used in the request.
         * The content of this attribute is a u32 array for one or more of
         * hardware capabilities (attribute IDs) that are being requested. Each
         * u32 value has a value from this
         * enum qca_wlan_vendor_attr_get_hw_capability
         * identifying which capabilities are requested.
         */
        QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX =
        QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring
 *    offload which is an extension for LL_STATS.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms.
 *    If MAC counters do not exceed the threshold, FW will report monitored
 *    link layer counters periodically as this setting. The first report is
 *    always triggered by this timer.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99).
 *    For each MAC layer counter, FW holds two copies. One is the current value.
 *    The other is the last report. Once a current counter's increment is larger
 *    than the threshold, FW will indicate that counter to host even if the
 *    monitoring timer does not expire.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same
 *    failure code.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code
 *    1: TX packet discarded
 *    2: No ACK
 *    3: Postpone
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS: peer MAC address
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE: Peer STA current state
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL: Global threshold.
 *    Threshold for all monitored parameters. If per counter dedicated threshold
 *    is not enabled, this threshold will take effect.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE: Indicate what triggers this
 *    event, PERORID_TIMEOUT == 1, THRESH_EXCEED == 0.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID: interface ID
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID: peer ID
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP: bitmap for TX counters
 *    Bit0: TX counter unit in MSDU
 *    Bit1: TX counter unit in MPDU
 *    Bit2: TX counter unit in PPDU
 *    Bit3: TX counter unit in byte
 *    Bit4: Dropped MSDUs
 *    Bit5: Dropped Bytes
 *    Bit6: MPDU retry counter
 *    Bit7: MPDU failure counter
 *    Bit8: PPDU failure counter
 *    Bit9: MPDU aggregation counter
 *    Bit10: MCS counter for ACKed MPDUs
 *    Bit11: MCS counter for Failed MPDUs
 *    Bit12: TX Delay counter
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP: bitmap for RX counters
 *    Bit0: MAC RX counter unit in MPDU
 *    Bit1: MAC RX counter unit in byte
 *    Bit2: PHY RX counter unit in PPDU
 *    Bit3: PHY RX counter unit in byte
 *    Bit4: Disorder counter
 *    Bit5: Retry counter
 *    Bit6: Duplication counter
 *    Bit7: Discard counter
 *    Bit8: MPDU aggregation size counter
 *    Bit9: MCS counter
 *    Bit10: Peer STA power state change (wake to sleep) counter
 *    Bit11: Peer STA power save counter, total time in PS mode
 *    Bit12: Probe request counter
 *    Bit13: Other management frames counter
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP: bitmap for CCA
 *    Bit0: Idle time
 *    Bit1: TX time
 *    Bit2: time RX in current bss
 *    Bit3: Out of current bss time
 *    Bit4: Wireless medium busy time
 *    Bit5: RX in bad condition time
 *    Bit6: TX in bad condition time
 *    Bit7: time wlan card not available
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP: bitmap for signal
 *    Bit0: Per channel SNR counter
 *    Bit1: Per channel noise floor counter
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM: number of peers
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM: number of channels
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_AC_RX_NUM: number of RX stats
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS: per channel BSS CCA stats
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER: container for per PEER stats
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU: Number of total TX MSDUs
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU: Number of total TX MPDUs
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU: Number of total TX PPDUs
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES: bytes of TX data
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP: Number of dropped TX packets
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES: Bytes dropped
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY: waiting time without an ACK
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK: number of MPDU not-ACKed
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK: number of PPDU not-ACKed
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM:
 *    aggregation stats buffer length
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM: length of mcs stats
 *    buffer for ACKed MPDUs.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM: length of mcs stats
 *    buffer for failed MPDUs.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE:
 *    length of delay stats array.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR: TX aggregation stats
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS: MCS stats for ACKed MPDUs
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS: MCS stats for failed MPDUs
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY: tx delay stats
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU: MPDUs received
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES: bytes received
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU: PPDU received
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES: PPDU bytes received
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST: packets lost
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY: number of RX packets
 *    flagged as retransmissions
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP: number of RX packets
 *    flagged as duplicated
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD: number of RX
 *    packets discarded
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM: length of RX aggregation
 *    stats buffer.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM: length of RX mcs
 *    stats buffer.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS: RX mcs stats buffer
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR: aggregation stats buffer
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES: times STAs go to sleep
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION: STAs' total sleep time
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ: number of probe
 *    requests received
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT: number of other mgmt
 *    frames received
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME: Percentage of idle time
 *    there is no TX, nor RX, nor interference.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME: percentage of time
 *    transmitting packets.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME: percentage of time
 *    for receiving.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY: percentage of time
 *    interference detected.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD: percentage of time
 *    receiving packets with errors.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD: percentage of time
 *    TX no-ACK.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL: percentage of time
 *    the chip is unable to work in normal conditions.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME: percentage of time
 *    receiving packets in current BSS.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME: percentage of time
 *    receiving packets not in current BSS.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM: number of antennas
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL:
 *    This is a container for per antenna signal stats.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR: per antenna SNR value
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF: per antenna NF value
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON: RSSI of beacon
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON: SNR of beacon
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME: u64
 *    Absolute timestamp from 1970/1/1, unit in ms. After receiving the
 *    message, user layer APP could call gettimeofday to get another
 *    timestamp and calculate transfer delay for the message.
 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME: u32
 *    Real period for this measurement, unit in us.
 */
enum qca_wlan_vendor_attr_ll_stats_ext {
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0,

        /* Attributes for configurations */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD,

        /* Peer STA power state change */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG,

        /* TX failure event */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS,

        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS,

        /* MAC counters */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER,

        /* Sub-attributes for PEER_AC_TX */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY,

        /* Sub-attributes for PEER_AC_RX */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT,

        /* Sub-attributes for CCA_BSS */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL,

        /* sub-attribute for BSS_RX_TIME */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME,

        /* Sub-attributes for PEER_SIGNAL */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF,

        /* Sub-attributes for IFACE_BSS */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON,

        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME,

        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX =
                QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1
};

/* Attributes for FTM commands and events */

/**
 * enum qca_wlan_vendor_attr_loc_capa - Indoor location capabilities
 *
 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS: Various flags. See
 *      enum qca_wlan_vendor_attr_loc_capa_flags.
 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS: Maximum number
 *      of measurement sessions that can run concurrently.
 *      Default is one session (no session concurrency).
 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS: The total number of unique
 *      peers that are supported in running sessions. For example,
 *      if the value is 8 and maximum number of sessions is 2, you can
 *      have one session with 8 unique peers, or 2 sessions with 4 unique
 *      peers each, and so on.
 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP: Maximum number
 *      of bursts per peer, as an exponent (2^value). Default is 0,
 *      meaning no multi-burst support.
 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST: Maximum number
 *      of measurement exchanges allowed in a single burst.
 * @QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES: Supported AOA measurement
 *      types. A bit mask (unsigned 32 bit value), each bit corresponds
 *      to an AOA type as defined by enum qca_vendor_attr_aoa_type.
 */
enum qca_wlan_vendor_attr_loc_capa {
        QCA_WLAN_VENDOR_ATTR_LOC_CAPA_INVALID,
        QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS,
        QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS,
        QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS,
        QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP,
        QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST,
        QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_LOC_CAPA_MAX =
        QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_loc_capa_flags: Indoor location capability flags
 *
 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER: Set if driver
 *      can be configured as an FTM responder (for example, an AP that
 *      services FTM requests). QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
 *      will be supported if set.
 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR: Set if driver
 *      can run FTM sessions. QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION
 *      will be supported if set.
 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP: Set if FTM responder
 *      supports immediate (ASAP) response.
 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA: Set if driver supports standalone
 *      AOA measurement using QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS.
 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM: Set if driver supports
 *      requesting AOA measurements as part of an FTM session.
 */
enum qca_wlan_vendor_attr_loc_capa_flags {
        QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER = 1 << 0,
        QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR = 1 << 1,
        QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP = 1 << 2,
        QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA = 1 << 3,
        QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM = 1 << 4,
};

/**
 * enum qca_wlan_vendor_attr_ftm_peer_info: Information about
 *      a single peer in a measurement session.
 *
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR: The MAC address of the peer.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS: Various flags related
 *      to measurement. See enum qca_wlan_vendor_attr_ftm_peer_meas_flags.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS: Nested attribute of
 *      FTM measurement parameters, as specified by IEEE P802.11-REVmc/D7.0
 *      9.4.2.167. See enum qca_wlan_vendor_attr_ftm_meas_param for
 *      list of supported attributes.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID: Initial token ID for
 *      secure measurement.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD: Request AOA
 *      measurement every <value> bursts. If 0 or not specified,
 *      AOA measurements will be disabled for this peer.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ: Frequency in MHz where
 *      the measurement frames are exchanged. Optional; if not
 *      specified, try to locate the peer in the kernel scan
 *      results cache and use frequency from there.
 */
enum qca_wlan_vendor_attr_ftm_peer_info {
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_INVALID,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAX =
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_ftm_peer_meas_flags: Measurement request flags,
 *      per-peer
 *
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP: If set, request
 *      immediate (ASAP) response from peer.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI: If set, request
 *      LCI report from peer. The LCI report includes the absolute
 *      location of the peer in "official" coordinates (similar to GPS).
 *      See IEEE P802.11-REVmc/D7.0, 11.24.6.7 for more information.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR: If set, request
 *      Location civic report from peer. The LCR includes the location
 *      of the peer in free-form format. See IEEE P802.11-REVmc/D7.0,
 *      11.24.6.7 for more information.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE: If set,
 *      request a secure measurement.
 *      QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID must also be provided.
 */
enum qca_wlan_vendor_attr_ftm_peer_meas_flags {
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP    = 1 << 0,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI     = 1 << 1,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR     = 1 << 2,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE  = 1 << 3,
};

/**
 * enum qca_wlan_vendor_attr_ftm_meas_param: Measurement parameters
 *
 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST: Number of measurements
 *      to perform in a single burst.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP: Number of bursts to
 *      perform, specified as an exponent (2^value).
 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION: Duration of burst
 *      instance, as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD: Time between bursts,
 *      as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. Must
 *      be larger than QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION.
 */
enum qca_wlan_vendor_attr_ftm_meas_param {
        QCA_WLAN_VENDOR_ATTR_FTM_PARAM_INVALID,
        QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST,
        QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP,
        QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION,
        QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MAX =
        QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_ftm_peer_result: Per-peer results
 *
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR: MAC address of the reported
 *       peer.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS: Status of measurement
 *      request for this peer.
 *      See enum qca_wlan_vendor_attr_ftm_peer_result_status.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS: Various flags related
 *      to measurement results for this peer.
 *      See enum qca_wlan_vendor_attr_ftm_peer_result_flags.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS: Specified when
 *      request failed and peer requested not to send an additional request
 *      for this number of seconds.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI: LCI report when received
 *      from peer. In the format specified by IEEE P802.11-REVmc/D7.0,
 *      9.4.2.22.10.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR: Location civic report when
 *      received from peer. In the format specified by IEEE P802.11-REVmc/D7.0,
 *      9.4.2.22.13.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS: Reported when peer
 *      overridden some measurement request parameters. See
 *      enum qca_wlan_vendor_attr_ftm_meas_param.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS: AOA measurement
 *      for this peer. Same contents as @QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS: Array of measurement
 *      results. Each entry is a nested attribute defined
 *      by enum qca_wlan_vendor_attr_ftm_meas.
 */
enum qca_wlan_vendor_attr_ftm_peer_result {
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_INVALID,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAX =
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_ftm_peer_result_status
 *
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK: Request sent ok and results
 *      will be provided. Peer may have overridden some measurement parameters,
 *      in which case overridden parameters will be report by
 *      QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAM attribute.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE: Peer is incapable
 *      of performing the measurement request. No more results will be sent
 *      for this peer in this session.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED: Peer reported request
 *      failed, and requested not to send an additional request for number
 *      of seconds specified by QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS
 *      attribute.
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID: Request validation
 *      failed. Request was not sent over the air.
 */
enum qca_wlan_vendor_attr_ftm_peer_result_status {
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED,
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID,
};

/**
 * enum qca_wlan_vendor_attr_ftm_peer_result_flags: Various flags
 *  for measurement result, per-peer
 *
 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE: If set,
 *      measurement completed for this peer. No more results will be reported
 *      for this peer in this session.
 */
enum qca_wlan_vendor_attr_ftm_peer_result_flags {
        QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE = 1 << 0,
};

/**
 * enum qca_vendor_attr_loc_session_status: Session completion status code
 *
 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK: Session completed
 *      successfully.
 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED: Session aborted
 *      by request.
 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID: Session request
 *      was invalid and was not started.
 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED: Session had an error
 *      and did not complete normally (for example out of resources).
 */
enum qca_vendor_attr_loc_session_status {
        QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK,
        QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED,
        QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID,
        QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED,
};

/**
 * enum qca_wlan_vendor_attr_ftm_meas: Single measurement data
 *
 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1: Time of departure (TOD) of FTM packet as
 *      recorded by responder, in picoseconds.
 *      See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2: Time of arrival (TOA) of FTM packet at
 *      initiator, in picoseconds.
 *      See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3: TOD of ACK packet as recorded by
 *      initiator, in picoseconds.
 *      See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4: TOA of ACK packet at
 *      responder, in picoseconds.
 *      See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI: RSSI (signal level) as recorded
 *      during this measurement exchange. Optional and will be provided if
 *      the hardware can measure it.
 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR: TOD error reported by
 *      responder. Not always provided.
 *      See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR: TOA error reported by
 *      responder. Not always provided.
 *      See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR: TOD error measured by
 *      initiator. Not always provided.
 *      See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR: TOA error measured by
 *      initiator. Not always provided.
 *      See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD: Dummy attribute for padding.
 */
enum qca_wlan_vendor_attr_ftm_meas {
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID,
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1,
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2,
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3,
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4,
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI,
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR,
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR,
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR,
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR,
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_MAX =
        QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_aoa_type - AOA measurement type
 *
 * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: Phase of the strongest
 *      CIR (channel impulse response) path for each antenna.
 * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: Phase and amplitude
 *      of the strongest CIR path for each antenna.
 */
enum qca_wlan_vendor_attr_aoa_type {
        QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE,
        QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP,
        QCA_WLAN_VENDOR_ATTR_AOA_TYPE_MAX
};

/**
 * enum qca_wlan_vendor_attr_encryption_test - Attributes to
 * validate encryption engine
 *
 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION: Flag attribute.
 *      This will be included if the request is for decryption; if not included,
 *      the request is treated as a request for encryption by default.
 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER: Unsigned 32-bit value
 *      indicating the key cipher suite. Takes same values as
 *      NL80211_ATTR_KEY_CIPHER.
 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID: Unsigned 8-bit value
 *      Key Id to be used for encryption
 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK: Array of 8-bit values.
 *      Key (TK) to be used for encryption/decryption
 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN: Array of 8-bit values.
 *      Packet number to be specified for encryption/decryption
 *      6 bytes for TKIP/CCMP/GCMP.
 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA: Array of 8-bit values
 *      representing the 802.11 packet (header + payload + FCS) that
 *      needs to be encrypted/decrypted.
 *      Encrypted/decrypted response from the driver will also be sent
 *      to userspace with the same attribute.
 */
enum qca_wlan_vendor_attr_encryption_test {
        QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION,
        QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER,
        QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID,
        QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK,
        QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN,
        QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_MAX =
        QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST - 1
};

/**
 * enum qca_wlan_vendor_attr_dmg_rf_sector_type - Type of
 * sector for DMG RF sector operations.
 *
 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX: RX sector
 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX: TX sector
 */
enum qca_wlan_vendor_attr_dmg_rf_sector_type {
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX,
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX,
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_MAX
};

/**
 * BRP antenna limit mode
 *
 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE: Disable BRP force
 *      antenna limit, BRP will be performed as usual.
 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE: Define maximal
 *      antennas limit. the hardware may use less antennas than the
 *      maximum limit.
 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE: The hardware will
 *      use exactly the specified number of antennas for BRP.
 */
enum qca_wlan_vendor_attr_brp_ant_limit_mode {
        QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE,
        QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE,
        QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE,
        QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_MAX
};

/**
 * enum qca_wlan_vendor_attr_dmg_rf_sector_cfg - Attributes for
 * DMG RF sector configuration for a single RF module.
 * The values are defined in a compact way which closely matches
 * the way it is stored in HW registers.
 * The configuration provides values for 32 antennas and 8 distribution
 * amplifiers, and together describes the characteristics of the RF
 * sector - such as a beam in some direction with some gain.
 *
 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX: Index
 *      of RF module for this configuration.
 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0: Bit 0 of edge
 *      amplifier gain index. Unsigned 32 bit number containing
 *      bits for all 32 antennas.
 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1: Bit 1 of edge
 *      amplifier gain index. Unsigned 32 bit number containing
 *      bits for all 32 antennas.
 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2: Bit 2 of edge
 *      amplifier gain index. Unsigned 32 bit number containing
 *      bits for all 32 antennas.
 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI: Phase values
 *      for first 16 antennas, 2 bits per antenna.
 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO: Phase values
 *      for last 16 antennas, 2 bits per antenna.
 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16: Contains
 *      DTYPE values (3 bits) for each distribution amplifier, followed
 *      by X16 switch bits for each distribution amplifier. There are
 *      total of 8 distribution amplifiers.
 */
enum qca_wlan_vendor_attr_dmg_rf_sector_cfg {
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX = 1,
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0 = 2,
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1 = 3,
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2 = 4,
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI = 5,
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO = 6,
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16 = 7,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MAX =
        QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST - 1
};

enum qca_wlan_vendor_attr_ll_stats_set {
        QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_INVALID = 0,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_MPDU_SIZE_THRESHOLD = 1,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_AGGRESSIVE_STATS_GATHERING = 2,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_MAX =
        QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST - 1,
};

enum qca_wlan_vendor_attr_ll_stats_clr {
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_INVALID = 0,
        /* Unsigned 32bit bitmap for clearing statistics
         * All radio statistics                     0x00000001
         * cca_busy_time (within radio statistics)  0x00000002
         * All channel stats (within radio statistics) 0x00000004
         * All scan statistics (within radio statistics) 0x00000008
         * All interface statistics                     0x00000010
         * All tx rate statistics (within interface statistics) 0x00000020
         * All ac statistics (with in interface statistics) 0x00000040
         * All contention (min, max, avg) statistics (within ac statisctics)
         * 0x00000080.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK = 1,
        /* Unsigned 8 bit value: Request to stop statistics collection */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_REQ = 2,

        /* Unsigned 32 bit bitmap: Response from the driver
         * for the cleared statistics
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK = 3,
        /* Unsigned 8 bit value: Response from driver/firmware
         * for the stop request
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP = 4,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_MAX =
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST - 1,
};

enum qca_wlan_vendor_attr_ll_stats_get {
        QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_INVALID = 0,
        /* Unsigned 32 bit value provided by the caller issuing the GET stats
         * command. When reporting the stats results, the driver uses the same
         * value to indicate which GET request the results correspond to.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_ID = 1,
        /* Unsigned 32 bit value - bit mask to identify what statistics are
         * requested for retrieval.
         * Radio Statistics 0x00000001
         * Interface Statistics 0x00000020
         * All Peer Statistics 0x00000040
         * Peer Statistics     0x00000080
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK = 2,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_MAX =
        QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST - 1,
};

enum qca_wlan_vendor_attr_ll_stats_results {
        QCA_WLAN_VENDOR_ATTR_LL_STATS_INVALID = 0,
        /* Unsigned 32bit value. Used by the driver; must match the request id
         * provided with the QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET command.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_REQ_ID = 1,

        /* Unsigned 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_BEACON_RX = 2,
        /* Unsigned 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_RX = 3,
        /* Unsigned 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_RX = 4,
        /* Unsigned 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_TX = 5,
        /* Signed 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_MGMT = 6,
        /* Signed 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_DATA = 7,
        /* Signed 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_ACK = 8,

        /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_* are
         * nested within the interface stats.
         */

        /* Interface mode, e.g., STA, SOFTAP, IBSS, etc.
         * Type = enum wifi_interface_mode.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MODE = 9,
        /* Interface MAC address. An array of 6 Unsigned int8 */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MAC_ADDR = 10,
        /* Type = enum wifi_connection_state, e.g., DISCONNECTED,
         * AUTHENTICATING, etc. valid for STA, CLI only.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_STATE = 11,
        /* Type = enum wifi_roam_state. Roaming state, e.g., IDLE or ACTIVE
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_ROAMING = 12,
        /* Unsigned 32 bit value. WIFI_CAPABILITY_XXX */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_CAPABILITIES = 13,
        /* NULL terminated SSID. An array of 33 Unsigned 8bit values */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_SSID = 14,
        /* BSSID. An array of 6 unsigned 8 bit values */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_BSSID = 15,
        /* Country string advertised by AP. An array of 3 unsigned 8 bit
         * values.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_AP_COUNTRY_STR = 16,
        /* Country string for this association. An array of 3 unsigned 8 bit
         * values.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_COUNTRY_STR = 17,

        /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* could
         * be nested within the interface stats.
         */

        /* Type = enum wifi_traffic_ac, e.g., V0, VI, BE and BK */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_AC = 18,
        /* Unsigned int 32 value corresponding to respective AC */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MPDU = 19,
        /* Unsigned int 32 value corresponding to respective AC */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MPDU = 20,
        /* Unsigned int 32 value corresponding to respective AC */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MCAST = 21,
        /* Unsigned int 32 value corresponding to respective AC */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MCAST = 22,
        /* Unsigned int 32 value corresponding to respective AC */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_AMPDU = 23,
        /* Unsigned int 32 value corresponding to respective AC */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_AMPDU = 24,
        /* Unsigned int 32 value corresponding to respective AC */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_MPDU_LOST = 25,
        /* Unsigned int 32 value corresponding to respective AC */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES = 26,
        /* Unsigned int 32 value corresponding to respective AC  */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_SHORT = 27,
        /* Unsigned int 32 values corresponding to respective AC */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_LONG = 28,
        /* Unsigned int 32 values corresponding to respective AC */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MIN = 29,
        /* Unsigned int 32 values corresponding to respective AC */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MAX = 30,
        /* Unsigned int 32 values corresponding to respective AC */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_AVG = 31,
        /* Unsigned int 32 values corresponding to respective AC */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_NUM_SAMPLES = 32,
        /* Unsigned 32 bit value. Number of peers */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NUM_PEERS = 33,

        /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* are
         * nested within the interface stats.
         */

        /* Type = enum wifi_peer_type. Peer type, e.g., STA, AP, P2P GO etc. */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_TYPE = 34,
        /* MAC addr corresponding to respective peer. An array of 6 unsigned
         * 8 bit values.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_MAC_ADDRESS = 35,
        /* Unsigned int 32 bit value representing capabilities corresponding
         * to respective peer.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_CAPABILITIES = 36,
        /* Unsigned 32 bit value. Number of rates */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_NUM_RATES = 37,

        /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_*
         * are nested within the rate stat.
         */

        /* Wi-Fi Rate - separate attributes defined for individual fields */

        /* Unsigned int 8 bit value; 0: OFDM, 1:CCK, 2:HT 3:VHT 4..7 reserved */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_PREAMBLE = 38,
        /* Unsigned int 8 bit value; 0:1x1, 1:2x2, 3:3x3, 4:4x4 */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_NSS = 39,
        /* Unsigned int 8 bit value; 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BW = 40,
        /* Unsigned int 8 bit value; OFDM/CCK rate code would be as per IEEE Std
         * in the units of 0.5 Mbps HT/VHT it would be MCS index
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MCS_INDEX = 41,

        /* Unsigned 32 bit value. Bit rate in units of 100 kbps */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BIT_RATE = 42,

        /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_STAT_* could be
         * nested within the peer info stats.
         */

        /* Unsigned int 32 bit value. Number of successfully transmitted data
         * packets, i.e., with ACK received corresponding to the respective
         * rate.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_TX_MPDU = 43,
        /* Unsigned int 32 bit value. Number of received data packets
         * corresponding to the respective rate.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RX_MPDU = 44,
        /* Unsigned int 32 bit value. Number of data packet losses, i.e., no ACK
         * received corresponding to the respective rate.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MPDU_LOST = 45,
        /* Unsigned int 32 bit value. Total number of data packet retries for
         * the respective rate.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES = 46,
        /* Unsigned int 32 bit value. Total number of short data packet retries
         * for the respective rate.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_SHORT = 47,
        /* Unsigned int 32 bit value. Total number of long data packet retries
         * for the respective rate.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_LONG = 48,

        QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ID = 49,
        /* Unsigned 32 bit value. Total number of msecs the radio is awake
         * accruing over time.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME = 50,
        /* Unsigned 32 bit value. Total number of msecs the radio is
         * transmitting accruing over time.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME = 51,
        /* Unsigned 32 bit value. Total number of msecs the radio is in active
         * receive accruing over time.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_RX_TIME = 52,
        /* Unsigned 32 bit value. Total number of msecs the radio is awake due
         * to all scan accruing over time.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_SCAN = 53,
        /* Unsigned 32 bit value. Total number of msecs the radio is awake due
         * to NAN accruing over time.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_NBD = 54,
        /* Unsigned 32 bit value. Total number of msecs the radio is awake due
         * to GSCAN accruing over time.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_GSCAN = 55,
        /* Unsigned 32 bit value. Total number of msecs the radio is awake due
         * to roam scan accruing over time.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_ROAM_SCAN = 56,
        /* Unsigned 32 bit value. Total number of msecs the radio is awake due
         * to PNO scan accruing over time.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_PNO_SCAN = 57,
        /* Unsigned 32 bit value. Total number of msecs the radio is awake due
         * to Hotspot 2.0 scans and GAS exchange accruing over time.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_HS20 = 58,
        /* Unsigned 32 bit value. Number of channels. */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_CHANNELS = 59,

        /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* could
         * be nested within the channel stats.
         */

        /* Type = enum wifi_channel_width. Channel width, e.g., 20, 40, 80 */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_WIDTH = 60,
        /* Unsigned 32 bit value. Primary 20 MHz channel. */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ = 61,
        /* Unsigned 32 bit value. Center frequency (MHz) first segment. */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ0 = 62,
        /* Unsigned 32 bit value. Center frequency (MHz) second segment. */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ1 = 63,

        /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* could be
         * nested within the radio stats.
         */

        /* Unsigned int 32 bit value representing total number of msecs the
         * radio is awake on that channel accruing over time, corresponding to
         * the respective channel.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ON_TIME = 64,
        /* Unsigned int 32 bit value representing total number of msecs the CCA
         * register is busy accruing over time corresponding to the respective
         * channel.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME = 65,

        QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS = 66,

        /* Signifies the nested list of channel attributes
         * QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_*
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO = 67,

        /* Signifies the nested list of peer info attributes
         * QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_*
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO = 68,

        /* Signifies the nested list of rate info attributes
         * QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_*
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_RATE_INFO = 69,

        /* Signifies the nested list of wmm info attributes
         * QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_*
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_INFO = 70,

        /* Unsigned 8 bit value. Used by the driver; if set to 1, it indicates
         * that more stats, e.g., peers or radio, are to follow in the next
         * QCA_NL80211_VENDOR_SUBCMD_LL_STATS_*_RESULTS event.
         * Otherwise, it is set to 0.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_MORE_DATA = 71,

        /* Unsigned 64 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_AVERAGE_TSF_OFFSET = 72,

        /* Unsigned 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_DETECTED = 73,

        /* Unsigned 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_AVG_NUM_FRAMES_LEAKED = 74,

        /* Unsigned 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_GUARD_TIME = 75,

        /* Unsigned 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE = 76,

        /* Unsigned 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_TX_LEVELS = 77,

        /* Number of msecs the radio spent in transmitting for each power level
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME_PER_LEVEL = 78,

        /* Unsigned 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_SUCC_CNT = 79,
        /* Unsigned 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_FAIL_CNT = 80,
        /* Unsigned 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_SUCC_CNT = 81,
        /* Unsigned 32 bit value */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_FAIL_CNT = 82,

        /* Unsigned int 32 value.
         * Pending MSDUs corresponding to respective AC.
         */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_PENDING_MSDU = 83,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_LL_STATS_MAX =
        QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST - 1,
};

enum qca_wlan_vendor_attr_ll_stats_type {
        QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_INVALID = 0,
        QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_RADIO = 1,
        QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_IFACE = 2,
        QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_PEERS = 3,

        /* keep last */
        QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST,
        QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_MAX =
        QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_tdls_configuration - Attributes for
 * TDLS configuration to the host driver.
 *
 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE: Configure the TDLS trigger
 *      mode in the host driver. enum qca_wlan_vendor_tdls_trigger_mode
 *      represents the different TDLS trigger modes.
 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD: Duration (u32) within
 *      which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD number
 *      of packets shall meet the criteria for implicit TDLS setup.
 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD: Number (u32) of Tx/Rx packets
 *      within a duration QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD
 *      to initiate a TDLS setup.
 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD: Time (u32) to initiate
 *      a TDLS Discovery to the peer.
 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT: Max number (u32) of
 *      discovery attempts to know the TDLS capability of the peer. A peer is
 *      marked as TDLS not capable if there is no response for all the attempts.
 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT: Represents a duration (u32)
 *      within which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD
 *      number of TX / RX frames meet the criteria for TDLS teardown.
 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD: Minimum number (u32)
 *      of Tx/Rx packets within a duration
 *      QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT to tear down a TDLS link.
 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD: Threshold
 *      corresponding to the RSSI of the peer below which a TDLS setup is
 *      triggered.
 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD: Threshold
 *      corresponding to the RSSI of the peer above which a TDLS teardown is
 *      triggered.
 */
enum qca_wlan_vendor_attr_tdls_configuration {
        QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE = 1,

        /* Attributes configuring the TDLS Implicit Trigger */
        QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD = 2,
        QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD = 3,
        QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD = 4,
        QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT = 5,
        QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT = 6,
        QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD = 7,
        QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD = 8,
        QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD = 9,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX =
        QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST - 1
};

/**
 * enum qca_wlan_vendor_tdls_trigger_mode: Represents the TDLS trigger mode in
 *      the driver
 *
 * The following are the different values for
 *      QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE.
 *
 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT: The trigger to initiate/teardown
 *      the TDLS connection to a respective peer comes from the user space.
 *      wpa_supplicant provides the commands TDLS_SETUP, TDLS_TEARDOWN,
 *      TDLS_DISCOVER to do this.
 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT: Host driver triggers this TDLS
 *      setup/teardown to the eligible peer once the configured criteria
 *      (such as TX/RX threshold, RSSI) is met. The attributes
 *      in QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IMPLICIT_PARAMS correspond to
 *      the different configuration criteria for the TDLS trigger from the
 *      host driver.
 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL: Enables the driver to trigger
 *      the TDLS setup / teardown through the implicit mode only to the
 *      configured MAC addresses (wpa_supplicant, with tdls_external_control=1,
 *      configures the MAC address through TDLS_SETUP / TDLS_TEARDOWN commands).
 *      External mode works on top of the implicit mode. Thus the host driver
 *      is expected to configure in TDLS Implicit mode too to operate in
 *      External mode.
 *      Configuring External mode alone without Implicit mode is invalid.
 *
 * All the above implementations work as expected only when the host driver
 * advertises the capability WPA_DRIVER_FLAGS_TDLS_EXTERNAL_SETUP - representing
 * that the TDLS message exchange is not internal to the host driver, but
 * depends on wpa_supplicant to do the message exchange.
 */
enum qca_wlan_vendor_tdls_trigger_mode {
        QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT = 1 << 0,
        QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT = 1 << 1,
        QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL = 1 << 2,
};

/**
 * enum qca_vendor_attr_sar_limits_selections - Source of SAR power limits
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0: Select SAR profile #0
 *      that is hard-coded in the Board Data File (BDF).
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1: Select SAR profile #1
 *      that is hard-coded in the Board Data File (BDF).
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2: Select SAR profile #2
 *      that is hard-coded in the Board Data File (BDF).
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3: Select SAR profile #3
 *      that is hard-coded in the Board Data File (BDF).
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4: Select SAR profile #4
 *      that is hard-coded in the Board Data File (BDF).
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE: Do not select any
 *      source of SAR power limits, thereby disabling the SAR power
 *      limit feature.
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER: Select the SAR power
 *      limits configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR.
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0: Select the SAR power
 *      limits version 2.0 configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR.
 *
 * This enumerates the valid set of values that may be supplied for
 * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT in an instance of
 * the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor command or in
 * the response to an instance of the
 * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command.
 */
enum qca_vendor_attr_sar_limits_selections {
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0 = 0,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1 = 1,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2 = 2,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3 = 3,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4 = 4,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE = 5,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER = 6,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0 = 7,
};

/**
 * enum qca_vendor_attr_sar_limits_spec_modulations -
 *      SAR limits specification modulation
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK -
 *      CCK modulation
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM -
 *      OFDM modulation
 *
 * This enumerates the valid set of values that may be supplied for
 * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION in an
 * instance of attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC in an
 * instance of the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor
 * command or in the response to an instance of the
 * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command.
 */
enum qca_vendor_attr_sar_limits_spec_modulations {
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK = 0,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM = 1,
};

/**
 * enum qca_vendor_attr_sar_limits - Attributes for SAR power limits
 *
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE: Optional (u32) value to
 *      select which SAR power limit table should be used. Valid
 *      values are enumerated in enum
 *      %qca_vendor_attr_sar_limits_selections. The existing SAR
 *      power limit selection is unchanged if this attribute is not
 *      present.
 *
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS: Optional (u32) value
 *      which specifies the number of SAR power limit specifications
 *      which will follow.
 *
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC: Nested array of SAR power
 *      limit specifications. The number of specifications is
 *      specified by @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS. Each
 *      specification contains a set of
 *      QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_* attributes. A
 *      specification is uniquely identified by the attributes
 *      %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND,
 *      %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN, and
 *      %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION and always
 *      contains as a payload the attribute
 *      %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT,
 *      %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX.
 *      Either %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT or
 *      %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX is
 *      needed based upon the value of
 *      %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE.
 *
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND: Optional (u32) value to
 *      indicate for which band this specification applies. Valid
 *      values are enumerated in enum %nl80211_band (although not all
 *      bands may be supported by a given device). If the attribute is
 *      not supplied then the specification will be applied to all
 *      supported bands.
 *
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN: Optional (u32) value
 *      to indicate for which antenna chain this specification
 *      applies, i.e. 1 for chain 1, 2 for chain 2, etc. If the
 *      attribute is not supplied then the specification will be
 *      applied to all chains.
 *
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION: Optional (u32)
 *      value to indicate for which modulation scheme this
 *      specification applies. Valid values are enumerated in enum
 *      %qca_vendor_attr_sar_limits_spec_modulations. If the attribute
 *      is not supplied then the specification will be applied to all
 *      modulation schemes.
 *
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT: Required (u32)
 *      value to specify the actual power limit value in units of 0.5
 *      dBm (i.e., a value of 11 represents 5.5 dBm).
 *      This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is
 *      %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER.
 *
 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX: Required (u32)
 *      value to indicate SAR V2 indices (0 - 11) to select SAR V2 profiles.
 *      This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is
 *      %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0.
 *
 * These attributes are used with %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS
 * and %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS.
 */
enum qca_vendor_attr_sar_limits {
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE = 1,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS = 2,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC = 3,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND = 4,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN = 5,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION = 6,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT = 7,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX = 8,

        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_MAX =
                QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST - 1
};

/**
 * enum qca_wlan_vendor_attr_get_wifi_info: Attributes for data used by
 * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO sub command.
 */
enum qca_wlan_vendor_attr_get_wifi_info {
        QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION = 1,
        QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION = 2,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX =
        QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST - 1,
};

/*
 * enum qca_wlan_vendor_attr_wifi_logger_start: Attributes for data used by
 * QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START sub command.
 */
enum qca_wlan_vendor_attr_wifi_logger_start {
        QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID = 1,
        QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL = 2,
        QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS = 3,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_GET_MAX =
        QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST - 1,
};

enum qca_wlan_vendor_attr_logger_results {
        QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_INVALID = 0,

        /* Unsigned 32-bit value; must match the request Id supplied by
         * Wi-Fi HAL in the corresponding subcmd NL msg.
         */
        QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_REQUEST_ID = 1,

        /* Unsigned 32-bit value; used to indicate the size of memory
         * dump to be allocated.
         */
        QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MEMDUMP_SIZE = 2,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MAX =
        QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST - 1,
};

enum qca_wlan_vendor_attr_roaming_config_params {
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID = 0,

        QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD = 1,
        QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID = 2,

        /* Attributes for wifi_set_ssid_white_list */
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS = 3,
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST = 4,
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID = 5,

        /* Attributes for set_roam_params */
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD = 6,
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD = 7,
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR = 8,
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR = 9,
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST = 10,
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS = 11,
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER = 12,

        /* Attribute for set_lazy_roam */
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE = 13,

        /* Attribute for set_lazy_roam with preferences */
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS = 14,
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID = 15,
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID = 16,
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER = 17,

        /* Attribute for set_blacklist bssid params */
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS = 18,
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID = 19,
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID = 20,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX =
        QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST - 1,
};

/*
 * enum qca_wlan_vendor_attr_roam_subcmd: Attributes for data used by
 * QCA_NL80211_VENDOR_SUBCMD_ROAM sub command.
 */
enum qca_wlan_vendor_attr_roam_subcmd {
        QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SSID_WHITE_LIST = 1,
        QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_GSCAN_ROAM_PARAMS = 2,
        QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_LAZY_ROAM = 3,
        QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PREFS = 4,
        QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PARAMS = 5,
        QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID = 6,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_MAX =
        QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST - 1,
};

enum qca_wlan_vendor_attr_gscan_config_params {
        QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_INVALID = 0,

        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_REQUEST_ID = 1,

        /* Attributes for data used by
         * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS sub command.
         */
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_WIFI_BAND
        = 2,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_MAX_CHANNELS
        = 3,

        /* Attributes for input params used by
         * QCA_NL80211_VENDOR_SUBCMD_GSCAN_START sub command.
         */

        /* Unsigned 32-bit value; channel frequency */
        QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CHANNEL = 4,
        /* Unsigned 32-bit value; dwell time in ms. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_DWELL_TIME = 5,
        /* Unsigned 8-bit value; 0: active; 1: passive; N/A for DFS */
        QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_PASSIVE = 6,
        /* Unsigned 8-bit value; channel class */
        QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CLASS = 7,

        /* Unsigned 8-bit value; bucket index, 0 based */
        QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_INDEX = 8,
        /* Unsigned 8-bit value; band. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BAND = 9,
        /* Unsigned 32-bit value; desired period, in ms. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_PERIOD = 10,
        /* Unsigned 8-bit value; report events semantics. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_REPORT_EVENTS = 11,
        /* Unsigned 32-bit value. Followed by a nested array of
         * GSCAN_CHANNEL_SPEC_* attributes.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS = 12,

        /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_* attributes.
         * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC = 13,

        /* Unsigned 32-bit value; base timer period in ms. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_BASE_PERIOD = 14,
        /* Unsigned 32-bit value; number of APs to store in each scan in the
         * BSSID/RSSI history buffer (keep the highest RSSI APs).
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_MAX_AP_PER_SCAN = 15,
        /* Unsigned 8-bit value; in %, when scan buffer is this much full, wake
         * up AP.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_PERCENT
        = 16,

        /* Unsigned 8-bit value; number of scan bucket specs; followed by a
         * nested array of_GSCAN_BUCKET_SPEC_* attributes and values. The size
         * of the array is determined by NUM_BUCKETS.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS = 17,

        /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_* attributes.
         * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC = 18,

        /* Unsigned 8-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_FLUSH
        = 19,
        /* Unsigned 32-bit value; maximum number of results to be returned. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_MAX
        = 20,

        /* An array of 6 x unsigned 8-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_BSSID = 21,
        /* Signed 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_LOW = 22,
        /* Signed 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_HIGH = 23,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_CHANNEL = 24,

        /* Number of hotlist APs as unsigned 32-bit value, followed by a nested
         * array of AP_THRESHOLD_PARAM attributes and values. The size of the
         * array is determined by NUM_AP.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_NUM_AP = 25,

        /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_* attributes.
         * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM = 26,

        /* Unsigned 32-bit value; number of samples for averaging RSSI. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_RSSI_SAMPLE_SIZE
        = 27,
        /* Unsigned 32-bit value; number of samples to confirm AP loss. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_LOST_AP_SAMPLE_SIZE
        = 28,
        /* Unsigned 32-bit value; number of APs breaching threshold. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_MIN_BREACHING = 29,
        /* Unsigned 32-bit value; number of APs. Followed by an array of
         * AP_THRESHOLD_PARAM attributes. Size of the array is NUM_AP.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_NUM_AP = 30,
        /* Unsigned 32-bit value; number of samples to confirm AP loss. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_LOST_AP_SAMPLE_SIZE
        = 31,
        /* Unsigned 32-bit value. If max_period is non zero or different than
         * period, then this bucket is an exponential backoff bucket.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_MAX_PERIOD = 32,
        /* Unsigned 32-bit value. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BASE = 33,
        /* Unsigned 32-bit value. For exponential back off bucket, number of
         * scans to perform for a given period.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_STEP_COUNT = 34,
        /* Unsigned 8-bit value; in number of scans, wake up AP after these
         * many scans.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_NUM_SCANS
        = 35,

        /* Attributes for data used by
         * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST sub command.
         */
        /* Unsigned 3-2bit value; number of samples to confirm SSID loss. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_LOST_SSID_SAMPLE_SIZE
        = 36,
        /* Number of hotlist SSIDs as unsigned 32-bit value, followed by a
         * nested array of SSID_THRESHOLD_PARAM_* attributes and values. The
         * size of the array is determined by NUM_SSID.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID = 37,
        /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_*
         * attributes.
         * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM = 38,

        /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_SSID = 39,
        /* Unsigned 8-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_BAND = 40,
        /* Signed 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_LOW = 41,
        /* Signed 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_HIGH = 42,
        /* Unsigned 32-bit value; a bitmask with additional gscan config flag.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_CONFIGURATION_FLAGS = 43,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_MAX =
        QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST - 1,
};

enum qca_wlan_vendor_attr_gscan_results {
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_INVALID = 0,

        /* Unsigned 32-bit value; must match the request Id supplied by
         * Wi-Fi HAL in the corresponding subcmd NL msg.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_REQUEST_ID = 1,

        /* Unsigned 32-bit value; used to indicate the status response from
         * firmware/driver for the vendor sub-command.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_STATUS = 2,

        /* GSCAN Valid Channels attributes */
        /* Unsigned 32bit value; followed by a nested array of CHANNELS. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_CHANNELS = 3,
        /* An array of NUM_CHANNELS x unsigned 32-bit value integers
         * representing channel numbers.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CHANNELS = 4,

        /* GSCAN Capabilities attributes */
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_CACHE_SIZE = 5,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_BUCKETS = 6,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_AP_CACHE_PER_SCAN
        = 7,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_RSSI_SAMPLE_SIZE
        = 8,
        /* Signed 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_REPORTING_THRESHOLD
        = 9,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_BSSIDS = 10,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SIGNIFICANT_WIFI_CHANGE_APS
        = 11,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_BSSID_HISTORY_ENTRIES
        = 12,

        /* GSCAN Attributes used with
         * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE sub-command.
         */

        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE = 13,

        /* GSCAN attributes used with
         * QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT sub-command.
         */

        /* An array of NUM_RESULTS_AVAILABLE x
         * QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_*
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST = 14,

        /* Unsigned 64-bit value; age of sample at the time of retrieval */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_TIME_STAMP = 15,
        /* 33 x unsigned 8-bit value; NULL terminated SSID */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_SSID = 16,
        /* An array of 6 x unsigned 8-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BSSID = 17,
        /* Unsigned 32-bit value; channel frequency in MHz */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CHANNEL = 18,
        /* Signed 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RSSI = 19,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT = 20,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT_SD = 21,
        /* Unsigned 16-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BEACON_PERIOD = 22,
        /* Unsigned 16-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CAPABILITY = 23,
        /* Unsigned 32-bit value; size of the IE DATA blob */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_LENGTH = 24,
        /* An array of IE_LENGTH x unsigned 8-bit value; blob of all the
         * information elements found in the beacon; this data should be a
         * packed list of wifi_information_element objects, one after the
         * other.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_DATA = 25,

        /* Unsigned 8-bit value; set by driver to indicate more scan results are
         * available.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_MORE_DATA = 26,

        /* GSCAN attributes for
         * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT sub-command.
         */
        /* Unsigned 8-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_TYPE = 27,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_STATUS = 28,

        /* GSCAN attributes for
         * QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND sub-command.
         */
        /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
         * to indicate number of results.
         * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the
         * list of results.
         */

        /* GSCAN attributes for
         * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE sub-command.
         */
        /* An array of 6 x unsigned 8-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_BSSID = 29,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_CHANNEL
        = 30,
        /* Unsigned 32-bit value. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_NUM_RSSI
        = 31,
        /* A nested array of signed 32-bit RSSI values. Size of the array is
         * determined by (NUM_RSSI of SIGNIFICANT_CHANGE_RESULT_NUM_RSSI.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_RSSI_LIST
        = 32,

        /* GSCAN attributes used with
         * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS sub-command.
         */
        /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
         * to indicate number of gscan cached results returned.
         * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST to indicate
         *  the list of gscan cached results.
         */

        /* An array of NUM_RESULTS_AVAILABLE x
         * QCA_NL80211_VENDOR_ATTR_GSCAN_CACHED_RESULTS_*
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST = 33,
        /* Unsigned 32-bit value; a unique identifier for the scan unit. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_SCAN_ID = 34,
        /* Unsigned 32-bit value; a bitmask w/additional information about scan.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_FLAGS = 35,
        /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
         * to indicate number of wifi scan results/bssids retrieved by the scan.
         * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the
         * list of wifi scan results returned for each cached result block.
         */

        /* GSCAN attributes for
         * QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND sub-command.
         */
        /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE for
         * number of results.
         * Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested
         * list of wifi scan results returned for each
         * wifi_passpoint_match_result block.
         * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE.
         */

        /* GSCAN attributes for
         * QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND sub-command.
         */
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES
        = 36,
        /* A nested array of
         * QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_*
         * attributes. Array size =
         * *_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_RESULT_LIST = 37,

        /* Unsigned 32-bit value; network block id for the matched network */
        QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ID = 38,
        /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested
         * list of wifi scan results returned for each
         * wifi_passpoint_match_result block.
         */
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP_LEN = 39,
        /* An array size of PASSPOINT_MATCH_ANQP_LEN of unsigned 8-bit values;
         * ANQP data in the information_element format.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP = 40,

        /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_SSIDS = 41,
        /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS = 42,
        /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS_BY_SSID
        = 43,
        /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_WHITELISTED_SSID
        = 44,

        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_BUCKETS_SCANNED = 45,

        /* Unsigned 32-bit value; a GSCAN Capabilities attribute.
         * This is used to limit the maximum number of BSSIDs while sending
         * the vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM with attributes
         * QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID and
         * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID.
         */
        QCA_WLAN_VENDOR_ATTR_GSCAN_MAX_NUM_BLACKLISTED_BSSID = 46,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_MAX =
        QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST - 1,
};

enum qca_wlan_vendor_attr_pno_config_params {
        QCA_WLAN_VENDOR_ATTR_PNO_INVALID = 0,
        /* Attributes for data used by
         * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST sub command.
         */
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM = 1,
        /* Array of nested QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_*
         * attributes. Array size =
         * QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM.
         */
        QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY = 2,

        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID = 3,
        /* An array of 256 x unsigned 8-bit value; NULL terminated UTF-8 encoded
         * realm, 0 if unspecified.
         */
        QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM = 4,
        /* An array of 16 x unsigned 32-bit value; roaming consortium ids to
         * match, 0 if unspecified.
         */
        QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID = 5,
        /* An array of 6 x unsigned 8-bit value; MCC/MNC combination, 0s if
         * unspecified.
         */
        QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN = 6,

        /* Attributes for data used by
         * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST sub command.
         */
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS = 7,
        /* Array of nested
         * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_*
         * attributes. Array size =
         * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS.
         */
        QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST = 8,
        /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */
        QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID = 9,
        /* Signed 8-bit value; threshold for considering this SSID as found,
         * required granularity for this threshold is 4 dBm to 8 dBm.
         */
        QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD
        = 10,
        /* Unsigned 8-bit value; WIFI_PNO_FLAG_XXX */
        QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS = 11,
        /* Unsigned 8-bit value; auth bit field for matching WPA IE */
        QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT = 12,
        /* Unsigned 8-bit to indicate ePNO type;
         * It takes values from qca_wlan_epno_type
         */
        QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE = 13,

        /* Nested attribute to send the channel list */
        QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST = 14,

        /* Unsigned 32-bit value; indicates the interval between PNO scan
         * cycles in msec.
         */
        QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL = 15,
        QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI = 16,
        QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI = 17,
        QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX = 18,
        QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS = 19,
        QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS = 20,
        QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS = 21,
        QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS = 22,
        /* Unsigned 32-bit value, representing the PNO Request ID */
        QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID = 23,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_PNO_MAX =
        QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST - 1,
};

/**
 * qca_wlan_vendor_acs_select_reason: This represents the different reasons why
 * the ACS has to be triggered. These values are used by
 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON and
 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON
 */
enum qca_wlan_vendor_acs_select_reason {
        /* Represents the reason that the ACS triggered during the AP start */
        QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT,
        /* Represents the reason that DFS found with the current channel */
        QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS,
        /* Represents the reason that LTE co-exist in the current band. */
        QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX,
};

/**
 * qca_wlan_vendor_attr_external_acs_policy: Attribute values for
 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to the vendor subcmd
 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This represents the
 * external ACS policies to select the channels w.r.t. the PCL weights.
 * (QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL represents the channels and
 * their PCL weights.)
 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY: Mandatory to
 * select a channel with non-zero PCL weight.
 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED: Prefer a
 * channel with non-zero PCL weight.
 *
 */
enum qca_wlan_vendor_attr_external_acs_policy {
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED,
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY,
};

/**
 * qca_wlan_vendor_channel_prop_flags: This represent the flags for a channel.
 * This is used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS.
 */
enum qca_wlan_vendor_channel_prop_flags {
        /* Bits 0, 1, 2, and 3 are reserved */

        /* Turbo channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_TURBO         = 1 << 4,
        /* CCK channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_CCK           = 1 << 5,
        /* OFDM channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_OFDM          = 1 << 6,
        /* 2.4 GHz spectrum channel. */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_2GHZ          = 1 << 7,
        /* 5 GHz spectrum channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_5GHZ          = 1 << 8,
        /* Only passive scan allowed */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_PASSIVE       = 1 << 9,
        /* Dynamic CCK-OFDM channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_DYN           = 1 << 10,
        /* GFSK channel (FHSS PHY) */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_GFSK          = 1 << 11,
        /* Radar found on channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_RADAR         = 1 << 12,
        /* 11a static turbo channel only */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_STURBO        = 1 << 13,
        /* Half rate channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HALF          = 1 << 14,
        /* Quarter rate channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_QUARTER       = 1 << 15,
        /* HT 20 channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT20          = 1 << 16,
        /* HT 40 with extension channel above */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40PLUS      = 1 << 17,
        /* HT 40 with extension channel below */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40MINUS     = 1 << 18,
        /* HT 40 intolerant */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOL     = 1 << 19,
        /* VHT 20 channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT20         = 1 << 20,
        /* VHT 40 with extension channel above */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40PLUS     = 1 << 21,
        /* VHT 40 with extension channel below */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40MINUS    = 1 << 22,
        /* VHT 80 channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80         = 1 << 23,
        /* HT 40 intolerant mark bit for ACS use */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOLMARK = 1 << 24,
        /* Channel temporarily blocked due to noise */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_BLOCKED       = 1 << 25,
        /* VHT 160 channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT160        = 1 << 26,
        /* VHT 80+80 channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80_80      = 1 << 27,
        /* HE 20 channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE20          = 1 << 28,
        /* HE 40 with extension channel above */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40PLUS      = 1 << 29,
        /* HE 40 with extension channel below */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40MINUS     = 1 << 30,
        /* HE 40 intolerant */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOL     = 1 << 31,
};

/**
 * qca_wlan_vendor_channel_prop_flags_2: This represents the flags for a
 * channel, and is a continuation of qca_wlan_vendor_channel_prop_flags. This is
 * used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2.
 */
enum qca_wlan_vendor_channel_prop_flags_2 {
        /* HE 40 intolerant mark bit for ACS use */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOLMARK = 1 << 0,
        /* HE 80 channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80          = 1 << 1,
        /* HE 160 channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE160         = 1 << 2,
        /* HE 80+80 channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80_80       = 1 << 3,
};

/**
 * qca_wlan_vendor_channel_prop_flags_ext: This represent the extended flags for
 * each channel. This is used by
 * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT.
 */
enum qca_wlan_vendor_channel_prop_flags_ext {
        /* Radar found on channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_RADAR_FOUND     = 1 << 0,
        /* DFS required on channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS             = 1 << 1,
        /* DFS required on channel for 2nd band of 80+80 */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CFREQ2      = 1 << 2,
        /* If channel has been checked for DFS */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CLEAR       = 1 << 3,
        /* Excluded in 802.11d */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_11D_EXCLUDED    = 1 << 4,
        /* Channel Switch Announcement received on this channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CSA_RECEIVED    = 1 << 5,
        /* Ad-hoc is not allowed */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_ADHOC  = 1 << 6,
        /* Station only channel */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_HOSTAP = 1 << 7,
        /* DFS radar history for slave device (STA mode) */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_HISTORY_RADAR   = 1 << 8,
        /* DFS CAC valid for slave device (STA mode) */
        QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CAC_VALID       = 1 << 9,
};

/**
 * qca_wlan_vendor_external_acs_event_chan_info_attr: Represents per channel
 * information. These attributes are sent as part of
 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO. Each set of the following
 * attributes correspond to a single channel.
 */
enum qca_wlan_vendor_external_acs_event_chan_info_attr {
        QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_INVALID = 0,

        /* A bitmask (u32) with flags specified in
         * enum qca_wlan_vendor_channel_prop_flags.
         */
        QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS = 1,
        /* A bitmask (u32) with flags specified in
         * enum qca_wlan_vendor_channel_prop_flags_ext.
         */
        QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT = 2,
        /* frequency in MHz (u32) */
        QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ = 3,
        /* maximum regulatory transmission power (u32) */
        QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER = 4,
        /* maximum transmission power (u32) */
        QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER = 5,
        /* minimum transmission power (u32) */
        QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER = 6,
        /* regulatory class id (u8) */
        QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID = 7,
        /* maximum antenna gain in (u8) */
        QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN = 8,
        /* VHT segment 0 (u8) */
        QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0 = 9,
        /* VHT segment 1 (u8) */
        QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1 = 10,
        /* A bitmask (u32) with flags specified in
         * enum qca_wlan_vendor_channel_prop_flags_2.
         */
        QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2 = 11,

        /* keep last */
        QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST,
        QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX =
                QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST - 1,
};

/**
 * qca_wlan_vendor_attr_pcl: Represents attributes for
 * preferred channel list (PCL). These attributes are sent as part of
 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL and
 * QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST.
 */
enum qca_wlan_vendor_attr_pcl {
        QCA_WLAN_VENDOR_ATTR_PCL_INVALID = 0,

        /* Channel number (u8) */
        QCA_WLAN_VENDOR_ATTR_PCL_CHANNEL = 1,
        /* Channel weightage (u8) */
        QCA_WLAN_VENDOR_ATTR_PCL_WEIGHT = 2,
        /* Channel frequency (u32) in MHz */
        QCA_WLAN_VENDOR_ATTR_PCL_FREQ = 3,
        /* Channel flags (u32)
         * bit 0 set: channel to be used for GO role,
         * bit 1 set: channel to be used on CLI role,
         * bit 2 set: channel must be considered for operating channel
         *                 selection & peer chosen operating channel should be
         *                 one of the channels with this flag set,
         * bit 3 set: channel should be excluded in GO negotiation
         */
        QCA_WLAN_VENDOR_ATTR_PCL_FLAG = 4,
};

/**
 * qca_wlan_vendor_attr_external_acs_event: Attribute to vendor sub-command
 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This attribute will be sent by
 * host driver.
 */
enum qca_wlan_vendor_attr_external_acs_event {
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_INVALID = 0,

        /* This reason (u8) refers to enum qca_wlan_vendor_acs_select_reason.
         * This helps ACS module to understand why ACS needs to be started.
         */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON = 1,
        /* Flag attribute to indicate if driver supports spectral scanning */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED = 2,
        /* Flag attribute to indicate if 11ac is offloaded to firmware */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED = 3,
        /* Flag attribute to indicate if driver provides additional channel
         * capability as part of scan operation
         */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT = 4,
        /* Flag attribute to indicate interface status is UP */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP = 5,
        /* Operating mode (u8) of interface. Takes one of enum nl80211_iftype
         * values.
         */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE = 6,
        /* Channel width (u8). It takes one of enum nl80211_chan_width values.
         * This is the upper bound of channel width. ACS logic should try to get
         * a channel with the specified width and if not found, look for lower
         * values.
         */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH = 7,
        /* This (u8) will hold values of one of enum nl80211_bands */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND = 8,
        /* PHY/HW mode (u8). Takes one of enum qca_wlan_vendor_acs_hw_mode
         * values
         */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE = 9,
        /* Array of (u32) supported frequency list among which ACS should choose
         * best frequency.
         */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST = 10,
        /* Preferred channel list by the driver which will have array of nested
         * values as per enum qca_wlan_vendor_attr_pcl attribute.
         */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL = 11,
        /* Array of nested attribute for each channel. It takes attr as defined
         * in enum qca_wlan_vendor_external_acs_event_chan_info_attr.
         */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO = 12,
        /* External ACS policy such as PCL mandatory, PCL preferred, etc.
         * It uses values defined in enum
         * qca_wlan_vendor_attr_external_acs_policy.
         */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY = 13,
        /* Reference RF Operating Parameter (RROP) availability information
         * (u16). It uses values defined in enum
         * qca_wlan_vendor_attr_rropavail_info.
         */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_RROPAVAIL_INFO = 14,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST,
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_MAX =
                QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST - 1,
};

/**
 * qca_wlan_vendor_attr_external_acs_channels: Attributes to vendor subcmd
 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This carries a list of channels
 * in priority order as decided after ACS operation in userspace.
 */
enum qca_wlan_vendor_attr_external_acs_channels {
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_INVALID = 0,

        /* One of reason code (u8) from enum qca_wlan_vendor_acs_select_reason
         */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON = 1,

        /* Array of nested values for each channel with following attributes:
         * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND,
         * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY,
         * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY,
         * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0,
         * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1,
         * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH
         */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST = 2,
        /* This (u8) will hold values of one of enum nl80211_bands */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND = 3,
        /* Primary channel (u8) */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY = 4,
        /* Secondary channel (u8) used for HT 40 MHz channels */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY = 5,
        /* VHT seg0 channel (u8) */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 = 6,
        /* VHT seg1 channel (u8) */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 = 7,
        /* Channel width (u8). Takes one of enum nl80211_chan_width values. */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH = 8,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST,
        QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_MAX =
                QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST - 1
};

enum qca_chip_power_save_failure_reason {
        /* Indicates if the reason for the failure is due to a protocol
         * layer/module.
         */
        QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL = 0,
        /* Indicates if the reason for the failure is due to a hardware issue.
         */
        QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE = 1,
};

/**
 * qca_attr_chip_power_save_failure: Attributes to vendor subcmd
 * QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE. This carries the requisite
 * information leading to the power save failure.
 */
enum qca_attr_chip_power_save_failure {
        QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID = 0,
        /* Reason to cause the power save failure.
         * These reasons are represented by
         * enum qca_chip_power_save_failure_reason.
         */
        QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON = 1,

        /* keep last */
        QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST,
        QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX =
                QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST - 1,
};

/**
 * qca_wlan_vendor_nud_stats_data_pkt_flags: Flag representing the various
 * data types for which the stats have to get collected.
 */
enum qca_wlan_vendor_nud_stats_data_pkt_flags {
        QCA_WLAN_VENDOR_NUD_STATS_DATA_ARP = 1 << 0,
        QCA_WLAN_VENDOR_NUD_STATS_DATA_DNS = 1 << 1,
        QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_HANDSHAKE = 1 << 2,
        QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV4 = 1 << 3,
        QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV6 = 1 << 4,
        /* Used by QCA_ATTR_NUD_STATS_PKT_TYPE only in nud stats get
         * to represent the stats of respective data type.
         */
        QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN = 1 << 5,
        QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN_ACK = 1 << 6,
        QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_ACK = 1 << 7,
};

enum qca_wlan_vendor_nud_stats_set_data_pkt_info {
        QCA_ATTR_NUD_STATS_DATA_PKT_INFO_INVALID = 0,
        /* Represents the data packet type to be monitored (u32).
         * Host driver tracks the stats corresponding to each data frame
         * represented by these flags.
         * These data packets are represented by
         * enum qca_wlan_vendor_nud_stats_data_pkt_flags
         */
        QCA_ATTR_NUD_STATS_DATA_PKT_INFO_TYPE = 1,
        /* Name corresponding to the DNS frame for which the respective DNS
         * stats have to get monitored (string). Max string length 255.
         */
        QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DNS_DOMAIN_NAME = 2,
        /* source port on which the respective proto stats have to get
         * collected (u32).
         */
        QCA_ATTR_NUD_STATS_DATA_PKT_INFO_SRC_PORT = 3,
        /* destination port on which the respective proto stats have to get
         * collected (u32).
         */
        QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_PORT = 4,
        /* IPv4 address for which the destined data packets have to be
         * monitored. (in network byte order), u32.
         */
        QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV4 = 5,
        /* IPv6 address for which the destined data packets have to be
         * monitored. (in network byte order), 16 bytes array.
         */
        QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV6 = 6,

        QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST,
        QCA_ATTR_NUD_STATS_DATA_PKT_INFO_MAX =
                QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST - 1,
};

/**
 * qca_wlan_vendor_attr_nud_stats_set: Attributes to vendor subcmd
 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carries the requisite
 * information to start/stop the NUD statistics collection.
 */
enum qca_attr_nud_stats_set {
        QCA_ATTR_NUD_STATS_SET_INVALID = 0,

        /* Flag to start/stop the NUD statistics collection.
         * Start - If included, Stop - If not included
         */
        QCA_ATTR_NUD_STATS_SET_START = 1,
        /* IPv4 address of the default gateway (in network byte order), u32 */
        QCA_ATTR_NUD_STATS_GW_IPV4 = 2,
        /* Represents the list of data packet types to be monitored.
         * Host driver tracks the stats corresponding to each data frame
         * represented by these flags.
         * These data packets are represented by
         * enum qca_wlan_vendor_nud_stats_set_data_pkt_info
         */
        QCA_ATTR_NUD_STATS_SET_DATA_PKT_INFO = 3,

        /* keep last */
        QCA_ATTR_NUD_STATS_SET_LAST,
        QCA_ATTR_NUD_STATS_SET_MAX =
                QCA_ATTR_NUD_STATS_SET_LAST - 1,
};

enum qca_attr_nud_data_stats {
        QCA_ATTR_NUD_DATA_STATS_INVALID = 0,
        /* Data packet type for which the stats are collected (u32).
         * Represented by enum qca_wlan_vendor_nud_stats_data_pkt_flags
         */
        QCA_ATTR_NUD_STATS_PKT_TYPE = 1,
        /* Name corresponding to the DNS frame for which the respective DNS
         * stats are monitored (string). Max string length 255.
         */
        QCA_ATTR_NUD_STATS_PKT_DNS_DOMAIN_NAME = 2,
        /* source port on which the respective proto stats are collected (u32).
         */
        QCA_ATTR_NUD_STATS_PKT_SRC_PORT = 3,
        /* destination port on which the respective proto stats are collected
         * (u32).
         */
        QCA_ATTR_NUD_STATS_PKT_DEST_PORT = 4,
        /* IPv4 address for which the destined data packets have to be
         * monitored. (in network byte order), u32.
         */
        QCA_ATTR_NUD_STATS_PKT_DEST_IPV4 = 5,
        /* IPv6 address for which the destined data packets have to be
         * monitored. (in network byte order), 16 bytes array.
         */
        QCA_ATTR_NUD_STATS_PKT_DEST_IPV6 = 6,
        /* Data packet Request count received from netdev (u32). */
        QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_FROM_NETDEV = 7,
        /* Data packet Request count sent to lower MAC from upper MAC (u32). */
        QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TO_LOWER_MAC = 8,
        /* Data packet Request count received by lower MAC from upper MAC
         * (u32)
         */
        QCA_ATTR_NUD_STATS_PKT_REQ_RX_COUNT_BY_LOWER_MAC = 9,
        /* Data packet Request count successfully transmitted by the device
         * (u32)
         */
        QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TX_SUCCESS = 10,
        /* Data packet Response count received by lower MAC (u32) */
        QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_LOWER_MAC = 11,
        /* Data packet Response count received by upper MAC (u32) */
        QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_UPPER_MAC = 12,
        /* Data packet Response count delivered to netdev (u32) */
        QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_TO_NETDEV = 13,
        /* Data Packet Response count that are dropped out of order (u32) */
        QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_OUT_OF_ORDER_DROP = 14,

        /* keep last */
        QCA_ATTR_NUD_DATA_STATS_LAST,
        QCA_ATTR_NUD_DATA_STATS_MAX =
                QCA_ATTR_NUD_DATA_STATS_LAST - 1,
};

/**
 * qca_attr_nud_stats_get: Attributes to vendor subcmd
 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET. This carries the requisite
 * NUD statistics collected when queried.
 */
enum qca_attr_nud_stats_get {
        QCA_ATTR_NUD_STATS_GET_INVALID = 0,
        /* ARP Request count from netdev (u32) */
        QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_FROM_NETDEV = 1,
        /* ARP Request count sent to lower MAC from upper MAC (u32) */
        QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TO_LOWER_MAC = 2,
        /* ARP Request count received by lower MAC from upper MAC (u32) */
        QCA_ATTR_NUD_STATS_ARP_REQ_RX_COUNT_BY_LOWER_MAC = 3,
        /* ARP Request count successfully transmitted by the device (u32) */
        QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TX_SUCCESS = 4,
        /* ARP Response count received by lower MAC (u32) */
        QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_LOWER_MAC = 5,
        /* ARP Response count received by upper MAC (u32) */
        QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_UPPER_MAC = 6,
        /* ARP Response count delivered to netdev (u32) */
        QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_TO_NETDEV = 7,
        /* ARP Response count dropped due to out of order reception (u32) */
        QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_OUT_OF_ORDER_DROP = 8,
        /* Flag indicating if the station's link to the AP is active.
         * Active Link - If included, Inactive link - If not included
         */
        QCA_ATTR_NUD_STATS_AP_LINK_ACTIVE = 9,
        /* Flag indicating if there is any duplicate address detected (DAD).
         * Yes - If detected, No - If not detected.
         */
        QCA_ATTR_NUD_STATS_IS_DAD = 10,
        /* List of Data packet types for which the stats are requested.
         * This list does not carry ARP stats as they are done by the
         * above attributes. Represented by enum qca_attr_nud_data_stats.
         */
        QCA_ATTR_NUD_STATS_DATA_PKT_STATS = 11,

        /* keep last */
        QCA_ATTR_NUD_STATS_GET_LAST,
        QCA_ATTR_NUD_STATS_GET_MAX =
                QCA_ATTR_NUD_STATS_GET_LAST - 1,
};

enum qca_wlan_btm_candidate_status {
        QCA_STATUS_ACCEPT = 0,
        QCA_STATUS_REJECT_EXCESSIVE_FRAME_LOSS_EXPECTED = 1,
        QCA_STATUS_REJECT_EXCESSIVE_DELAY_EXPECTED = 2,
        QCA_STATUS_REJECT_INSUFFICIENT_QOS_CAPACITY = 3,
        QCA_STATUS_REJECT_LOW_RSSI = 4,
        QCA_STATUS_REJECT_HIGH_INTERFERENCE = 5,
        QCA_STATUS_REJECT_UNKNOWN = 6,
};

enum qca_wlan_vendor_attr_btm_candidate_info {
        QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_INVALID = 0,

        /* 6-byte MAC address representing the BSSID of transition candidate */
        QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID = 1,
        /* Unsigned 32-bit value from enum qca_wlan_btm_candidate_status
         * returned by the driver. It says whether the BSSID provided in
         * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID is acceptable by
         * the driver, if not it specifies the reason for rejection.
         * Note that the user-space can overwrite the transition reject reason
         * codes provided by driver based on more information.
         */
        QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS = 2,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_MAX =
        QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST - 1,
};

enum qca_attr_trace_level {
        QCA_ATTR_TRACE_LEVEL_INVALID = 0,
        /*
         * Nested array of the following attributes:
         * QCA_ATTR_TRACE_LEVEL_MODULE,
         * QCA_ATTR_TRACE_LEVEL_MASK.
         */
        QCA_ATTR_TRACE_LEVEL_PARAM = 1,
        /*
         * Specific QCA host driver module. Please refer to the QCA host
         * driver implementation to get the specific module ID.
         */
        QCA_ATTR_TRACE_LEVEL_MODULE = 2,
        /* Different trace level masks represented in the QCA host driver. */
        QCA_ATTR_TRACE_LEVEL_MASK = 3,

        /* keep last */
        QCA_ATTR_TRACE_LEVEL_AFTER_LAST,
        QCA_ATTR_TRACE_LEVEL_MAX =
                QCA_ATTR_TRACE_LEVEL_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_get_he_capabilities - IEEE 802.11ax HE capabilities
 */
enum qca_wlan_vendor_attr_get_he_capabilities {
        QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_INVALID = 0,
        /* Whether HE capabilities is supported
         * (u8 attribute: 0 = not supported, 1 = supported)
         */
        QCA_WLAN_VENDOR_ATTR_HE_SUPPORTED = 1,
        /* HE PHY capabilities, array of 3 u32 values  */
        QCA_WLAN_VENDOR_ATTR_PHY_CAPAB = 2,
        /* HE MAC capabilities (u32 attribute) */
        QCA_WLAN_VENDOR_ATTR_MAC_CAPAB = 3,
        /* HE MCS map (u32 attribute) */
        QCA_WLAN_VENDOR_ATTR_HE_MCS = 4,
        /* Number of SS (u32 attribute) */
        QCA_WLAN_VENDOR_ATTR_NUM_SS = 5,
        /* RU count (u32 attribute) */
        QCA_WLAN_VENDOR_ATTR_RU_IDX_MASK = 6,
        /* PPE threshold data, array of 8 u32 values */
        QCA_WLAN_VENDOR_ATTR_PPE_THRESHOLD = 7,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_MAX =
        QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_spectral_scan - Spectral scan config parameters
 */
enum qca_wlan_vendor_attr_spectral_scan {
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INVALID = 0,
        /* Number of times the chip enters spectral scan mode before
         * deactivating spectral scans. When set to 0, chip will enter spectral
         * scan mode continuously. u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_COUNT = 1,
        /* Spectral scan period. Period increment resolution is 256*Tclk,
         * where Tclk = 1/44 MHz (Gmode), 1/40 MHz (Amode). u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_PERIOD = 2,
        /* Spectral scan priority. u32 attribute. */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PRIORITY = 3,
        /* Number of FFT data points to compute. u32 attribute. */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_SIZE = 4,
        /* Enable targeted gain change before starting the spectral scan FFT.
         * u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_GC_ENA = 5,
        /* Restart a queued spectral scan. u32 attribute. */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RESTART_ENA = 6,
        /* Noise floor reference number for the calculation of bin power.
         * u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NOISE_FLOOR_REF = 7,
        /* Disallow spectral scan triggers after TX/RX packets by setting
         * this delay value to roughly SIFS time period or greater.
         * u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INIT_DELAY = 8,
        /* Number of strong bins (inclusive) per sub-channel, below
         * which a signal is declared a narrow band tone. u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NB_TONE_THR = 9,
        /* Specify the threshold over which a bin is declared strong (for
         * scan bandwidth analysis). u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_STR_BIN_THR = 10,
        /* Spectral scan report mode. u32 attribute. */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_WB_RPT_MODE = 11,
        /* RSSI report mode, if the ADC RSSI is below
         * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR,
         * then FFTs will not trigger, but timestamps and summaries get
         * reported. u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_RPT_MODE = 12,
        /* ADC RSSI must be greater than or equal to this threshold (signed dB)
         * to ensure spectral scan reporting with normal error code.
         * u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR = 13,
        /* Format of frequency bin magnitude for spectral scan triggered FFTs:
         * 0: linear magnitude, 1: log magnitude (20*log10(lin_mag)).
         * u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PWR_FORMAT = 14,
        /* Format of FFT report to software for spectral scan triggered FFTs.
         * 0: No FFT report (only spectral scan summary report)
         * 1: 2-dword summary of metrics for each completed FFT + spectral scan
         * report
         * 2: 2-dword summary of metrics for each completed FFT + 1x-oversampled
         * bins (in-band) per FFT + spectral scan summary report
         * 3: 2-dword summary of metrics for each completed FFT + 2x-oversampled
         * bins (all) per FFT + spectral scan summary report
         * u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RPT_MODE = 15,
        /* Number of LSBs to shift out in order to scale the FFT bins.
         * u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BIN_SCALE = 16,
        /* Set to 1 (with spectral_scan_pwr_format=1), to report bin magnitudes
         * in dBm power. u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DBM_ADJ = 17,
        /* Per chain enable mask to select input ADC for search FFT.
         * u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_CHN_MASK = 18,
        /* An unsigned 64-bit integer provided by host driver to identify the
         * spectral scan request. This attribute is included in the scan
         * response message for @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START
         * and used as an attribute in
         * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP to identify the
         * specific scan to be stopped.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE = 19,
        /* Skip interval for FFT reports. u32 attribute */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_PERIOD = 20,
        /* Set to report only one set of FFT results.
         * u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SHORT_REPORT = 21,
        /* Debug level for spectral module in driver.
         * 0 : Verbosity level 0
         * 1 : Verbosity level 1
         * 2 : Verbosity level 2
         * 3 : Matched filterID display
         * 4 : One time dump of FFT report
         * u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DEBUG_LEVEL = 22,
        /* Type of spectral scan request. u32 attribute.
         * It uses values defined in enum
         * qca_wlan_vendor_attr_spectral_scan_request_type.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE = 23,

        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_MAX =
                QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_spectral_diag_stats - Used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS.
 */
enum qca_wlan_vendor_attr_spectral_diag_stats {
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_INVALID = 0,
        /* Number of spectral TLV signature mismatches.
         * u64 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SIG_MISMATCH = 1,
        /* Number of spectral phyerror events with insufficient length when
         * parsing for secondary 80 search FFT report. u64 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SEC80_SFFT_INSUFFLEN = 2,
        /* Number of spectral phyerror events without secondary 80
         * search FFT report. u64 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_NOSEC80_SFFT = 3,
        /* Number of spectral phyerror events with vht operation segment 1 id
         * mismatches in search fft report. u64 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG1ID_MISMATCH = 4,
        /* Number of spectral phyerror events with vht operation segment 2 id
         * mismatches in search fft report. u64 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG2ID_MISMATCH = 5,

        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_MAX =
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_spectral_cap - Used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO.
 */
enum qca_wlan_vendor_attr_spectral_cap {
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_INVALID = 0,
        /* Flag attribute to indicate phydiag capability */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_PHYDIAG = 1,
        /* Flag attribute to indicate radar detection capability */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RADAR = 2,
        /* Flag attribute to indicate spectral capability */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_SPECTRAL = 3,
        /* Flag attribute to indicate advanced spectral capability */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_ADVANCED_SPECTRAL = 4,
        /* Spectral hardware generation. u32 attribute.
         * It uses values defined in enum
         * qca_wlan_vendor_spectral_scan_cap_hw_gen.
         */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN = 5,

        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_MAX =
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_spectral_scan_status - used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS.
 */
enum qca_wlan_vendor_attr_spectral_scan_status {
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_INVALID = 0,
        /* Flag attribute to indicate whether spectral scan is enabled */
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ENABLED = 1,
        /* Flag attribute to indicate whether spectral scan is in progress*/
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ACTIVE = 2,

        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MAX =
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST - 1,
};

/**
 * qca_wlan_vendor_attr_spectral_scan_request_type: Attribute values for
 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE to the vendor subcmd
 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START. This represents the
 * spectral scan request types.
 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG: Request to
 * set the spectral parameters and start scan.
 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN: Request to
 * only set the spectral parameters.
 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG: Request to
 * only start the spectral scan.
 */
enum qca_wlan_vendor_attr_spectral_scan_request_type {
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG,
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN,
        QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG,
};

/**
 * qca_wlan_vendor_spectral_scan_cap_hw_gen: Attribute values for
 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN to the vendor subcmd
 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the
 * spectral hardware generation.
 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1: generation 1
 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2: generation 2
 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3: generation 3
 */
enum qca_wlan_vendor_spectral_scan_cap_hw_gen {
        QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1 = 0,
        QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2 = 1,
        QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3 = 2,
};

enum qca_wlan_vendor_tos {
        QCA_WLAN_VENDOR_TOS_BK = 0,
        QCA_WLAN_VENDOR_TOS_BE = 1,
        QCA_WLAN_VENDOR_TOS_VI = 2,
        QCA_WLAN_VENDOR_TOS_VO = 3,
};

/**
 * enum qca_wlan_vendor_attr_active_tos - Used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS.
 */
enum qca_wlan_vendor_attr_active_tos {
        QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_INVALID = 0,
        /* Type Of Service - Represented by qca_wlan_vendor_tos */
        QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS = 1,
        /* Flag attribute representing the start (attribute included) or stop
         * (attribute not included) of the respective TOS.
         */
        QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_START = 2,
};

enum qca_wlan_vendor_hang_reason {
        /* Unspecified reason */
        QCA_WLAN_HANG_REASON_UNSPECIFIED = 0,
        /* No Map for the MAC entry for the received frame */
        QCA_WLAN_HANG_RX_HASH_NO_ENTRY_FOUND = 1,
        /* Peer deletion timeout happened */
        QCA_WLAN_HANG_PEER_DELETION_TIMEDOUT = 2,
        /* Peer unmap timeout */
        QCA_WLAN_HANG_PEER_UNMAP_TIMEDOUT = 3,
        /* Scan request timed out */
        QCA_WLAN_HANG_SCAN_REQ_EXPIRED = 4,
        /* Consecutive Scan attempt failures */
        QCA_WLAN_HANG_SCAN_ATTEMPT_FAILURES = 5,
        /* Unable to get the message buffer */
        QCA_WLAN_HANG_GET_MSG_BUFF_FAILURE = 6,
        /* Current command processing is timedout */
        QCA_WLAN_HANG_ACTIVE_LIST_TIMEOUT = 7,
        /* Timeout for an ACK from FW for suspend request */
        QCA_WLAN_HANG_SUSPEND_TIMEOUT = 8,
        /* Timeout for an ACK from FW for resume request */
        QCA_WLAN_HANG_RESUME_TIMEOUT = 9,
        /* Transmission timeout for consecutive data frames */
        QCA_WLAN_HANG_TRANSMISSIONS_TIMEOUT = 10,
        /* Timeout for the TX completion status of data frame */
        QCA_WLAN_HANG_TX_COMPLETE_TIMEOUT = 11,
        /* DXE failure for TX/RX, DXE resource unavailability */
        QCA_WLAN_HANG_DXE_FAILURE = 12,
        /* WMI pending commands exceed the maximum count */
        QCA_WLAN_HANG_WMI_EXCEED_MAX_PENDING_CMDS = 13,
};

/**
 * enum qca_wlan_vendor_attr_hang - Used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_HANG.
 */
enum qca_wlan_vendor_attr_hang {
        QCA_WLAN_VENDOR_ATTR_HANG_INVALID = 0,
        /* Reason for the hang - u32 attribute with a value from enum
         * qca_wlan_vendor_hang_reason.
         */
        QCA_WLAN_VENDOR_ATTR_HANG_REASON = 1,

        QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_HANG_MAX =
                QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_flush_pending - Attributes for
 * flushing pending traffic in firmware.
 *
 * @QCA_WLAN_VENDOR_ATTR_PEER_ADDR: Configure peer MAC address.
 * @QCA_WLAN_VENDOR_ATTR_AC: Configure access category of the pending
 * packets. It is u8 value with bit 0~3 represent AC_BE, AC_BK,
 * AC_VI, AC_VO respectively. Set the corresponding bit to 1 to
 * flush packets with access category.
 */
enum qca_wlan_vendor_attr_flush_pending {
        QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_PEER_ADDR = 1,
        QCA_WLAN_VENDOR_ATTR_AC = 2,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_MAX =
        QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_rropavail_info - Specifies whether Representative
 * RF Operating Parameter (RROP) information is available, and if so, at which
 * point in the application-driver interaction sequence it can be retrieved by
 * the application from the driver. This point may vary by architecture and
 * other factors. This is a u16 value.
 */
enum qca_wlan_vendor_attr_rropavail_info {
        /* RROP information is unavailable. */
        QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_UNAVAILABLE,
        /* RROP information is available and the application can retrieve the
         * information after receiving an QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS
         * event from the driver.
         */
        QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_EXTERNAL_ACS_START,
        /* RROP information is available only after a vendor specific scan
         * (requested using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN) has
         * successfully completed. The application can retrieve the information
         * after receiving the QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE event from
         * the driver.
         */
        QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_VSCAN_END,
};

/**
 * enum qca_wlan_vendor_attr_rrop_info - Specifies vendor specific
 * Representative RF Operating Parameter (RROP) information. It is sent for the
 * vendor command QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO. This information is
 * intended for use by external Auto Channel Selection applications. It provides
 * guidance values for some RF parameters that are used by the system during
 * operation. These values could vary by channel, band, radio, and so on.
 */
enum qca_wlan_vendor_attr_rrop_info {
        QCA_WLAN_VENDOR_ATTR_RROP_INFO_INVALID = 0,

        /* Representative Tx Power List (RTPL) which has an array of nested
         * values as per attributes in enum qca_wlan_vendor_attr_rtplinst.
         */
        QCA_WLAN_VENDOR_ATTR_RROP_INFO_RTPL = 1,

        QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_RROP_INFO_MAX =
        QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST - 1
};

/**
 * enum qca_wlan_vendor_attr_rtplinst - Specifies attributes for individual list
 * entry instances in the Representative Tx Power List (RTPL). It provides
 * simplified power values intended for helping external Auto channel Selection
 * applications compare potential Tx power performance between channels, other
 * operating conditions remaining identical. These values are not necessarily
 * the actual Tx power values that will be used by the system. They are also not
 * necessarily the max or average values that will be used. Instead, they are
 * relative, summarized keys for algorithmic use computed by the driver or
 * underlying firmware considering a number of vendor specific factors.
 */
enum qca_wlan_vendor_attr_rtplinst {
        QCA_WLAN_VENDOR_ATTR_RTPLINST_INVALID = 0,

        /* Primary channel number (u8) */
        QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY = 1,
        /* Representative Tx power in dBm (s32) with emphasis on throughput. */
        QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_THROUGHPUT = 2,
        /* Representative Tx power in dBm (s32) with emphasis on range. */
        QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_RANGE = 3,

        QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_RTPLINST_MAX =
                QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_config_latency_level - Level for
 * wlan latency module.
 *
 * There will be various of Wi-Fi functionality like scan/roaming/adaptive
 * power saving which would causing data exchange out of service, this
 * would be a big impact on latency. For latency sensitive applications over
 * Wi-Fi are intolerant to such operations and thus would configure them
 * to meet their respective needs. It is well understood by such applications
 * that altering the default behavior would degrade the Wi-Fi functionality
 * w.r.t the above pointed WLAN operations.
 *
 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL:
 *      Default WLAN operation level which throughput orientated.
 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE:
 *      Use moderate level to improve latency by limit scan duration.
 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW:
 *      Use low latency level to benifit application like concurrent
 *      downloading or video streaming via constraint scan/adaptive PS.
 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW:
 *      Use ultra low latency level to benefit for gaming/voice
 *      application via constraint scan/roaming/adaptive PS.
 */
enum qca_wlan_vendor_attr_config_latency_level {
        QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL = 1,
        QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE = 2,
        QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW = 3,
        QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW = 4,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MAX =
        QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_wlan_mac - Used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO.
 */
enum qca_wlan_vendor_attr_mac {
        QCA_WLAN_VENDOR_ATTR_MAC_INVALID = 0,

        /* MAC mode info list which has an array of nested values as
         * per attributes in enum qca_wlan_vendor_attr_mac_mode_info.
         */
        QCA_WLAN_VENDOR_ATTR_MAC_INFO = 1,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_MAC_MAX =
        QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_mac_iface_info - Information of the connected
 *      Wi-Fi netdev interface on a respective MAC.
 *      Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO.
 */
enum qca_wlan_vendor_attr_mac_iface_info {
        QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_INVALID = 0,
        /* Wi-Fi netdev's interface index (u32) */
        QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_IFINDEX = 1,
        /* Associated frequency in MHz of the connected Wi-Fi interface (u32) */
        QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_FREQ = 2,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_MAX =
        QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_mac_info - Points to MAC the information.
 *      Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_INFO of the
 *      vendor command QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO.
 */
enum qca_wlan_vendor_attr_mac_info {
        QCA_WLAN_VENDOR_ATTR_MAC_INFO_INVALID = 0,
        /* Hardware MAC ID associated for the MAC (u32) */
        QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAC_ID = 1,
        /* Band supported by the MAC at a given point.
         * This is a u32 bitmask of BIT(NL80211_BAND_*) as described in %enum
         * nl80211_band.
         */
        QCA_WLAN_VENDOR_ATTR_MAC_INFO_BAND = 2,
        /* Refers to list of WLAN netdev interfaces associated with this MAC.
         * Represented by enum qca_wlan_vendor_attr_mac_iface_info.
         */
        QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO = 3,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAX =
        QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_get_logger_features - Used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET.
 */
enum qca_wlan_vendor_attr_get_logger_features {
        QCA_WLAN_VENDOR_ATTR_LOGGER_INVALID = 0,
        /* Unsigned 32-bit enum value of wifi_logger_supported_features */
        QCA_WLAN_VENDOR_ATTR_LOGGER_SUPPORTED = 1,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_LOGGER_MAX =
                QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST - 1,
};

/**
 * enum wifi_logger_supported_features - Values for supported logger features
 */
enum wifi_logger_supported_features {
        WIFI_LOGGER_MEMORY_DUMP_FEATURE = (1 << (0)),
        WIFI_LOGGER_PER_PACKET_TX_RX_STATUS_FEATURE = (1 << (1)),
        WIFI_LOGGER_CONNECT_EVENT_FEATURE = (1 << (2)),
        WIFI_LOGGER_POWER_EVENT_FEATURE = (1 << (3)),
        WIFI_LOGGER_WAKE_LOCK_FEATURE = (1 << (4)),
        WIFI_LOGGER_VERBOSE_FEATURE = (1 << (5)),
        WIFI_LOGGER_WATCHDOG_TIMER_FEATURE = (1 << (6)),
        WIFI_LOGGER_DRIVER_DUMP_FEATURE = (1 << (7)),
        WIFI_LOGGER_PACKET_FATE_FEATURE = (1 << (8)),
};

/**
 * enum qca_wlan_tdls_caps_features_supported - Values for TDLS get
 * capabilities features
 */
enum qca_wlan_tdls_caps_features_supported {
        WIFI_TDLS_SUPPORT = (1 << (0)),
        WIFI_TDLS_EXTERNAL_CONTROL_SUPPORT = (1 << (1)),
        WIFI_TDLS_OFFCHANNEL_SUPPORT = (1 << (2))
};

/**
 * enum qca_wlan_vendor_attr_tdls_get_capabilities - Used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES.
 */
enum qca_wlan_vendor_attr_tdls_get_capabilities {
        QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_INVALID = 0,
        /* Indicates the max concurrent sessions */
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX_CONC_SESSIONS,
        /* Indicates the support for features */
        /* Unsigned 32-bit bitmap qca_wlan_tdls_caps_features_supported
         */
        QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_FEATURES_SUPPORTED,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX =
                QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_offloaded_packets_sending_control - Offload packets control
 * command used as value for the attribute
 * QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL.
 */
enum qca_wlan_offloaded_packets_sending_control {
        QCA_WLAN_OFFLOADED_PACKETS_SENDING_CONTROL_INVALID = 0,
        QCA_WLAN_OFFLOADED_PACKETS_SENDING_START,
        QCA_WLAN_OFFLOADED_PACKETS_SENDING_STOP
};

/**
 * enum qca_wlan_vendor_attr_offloaded_packets - Used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS.
 */
enum qca_wlan_vendor_attr_offloaded_packets {
        QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_INVALID = 0,
        /* Takes valid value from the enum
         * qca_wlan_offloaded_packets_sending_control
         * Unsigned 32-bit value
         */
        QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_REQUEST_ID,
        /* array of u8 len: Max packet size */
        QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_IP_PACKET_DATA,
        /* 6-byte MAC address used to represent source MAC address */
        QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SRC_MAC_ADDR,
        /* 6-byte MAC address used to represent destination MAC address */
        QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_DST_MAC_ADDR,
        /* Unsigned 32-bit value, in milli seconds */
        QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_PERIOD,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_MAX =
                QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_rssi_monitoring_control - RSSI control commands used as values
 * by the attribute QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL.
 */
enum qca_wlan_rssi_monitoring_control {
        QCA_WLAN_RSSI_MONITORING_CONTROL_INVALID = 0,
        QCA_WLAN_RSSI_MONITORING_START,
        QCA_WLAN_RSSI_MONITORING_STOP,
};

/**
 * enum qca_wlan_vendor_attr_rssi_monitoring - Used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI.
 */
enum qca_wlan_vendor_attr_rssi_monitoring {
        QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_INVALID = 0,
        /* Takes valid value from the enum
         * qca_wlan_rssi_monitoring_control
         * Unsigned 32-bit value enum qca_wlan_rssi_monitoring_control
         */
        QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL,
        /* Unsigned 32-bit value */
        QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_REQUEST_ID,
        /* Signed 8-bit value in dBm */
        QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX_RSSI,
        /* Signed 8-bit value in dBm */
        QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MIN_RSSI,
        /* attributes to be used/received in callback */
        /* 6-byte MAC address used to represent current BSSID MAC address */
        QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_BSSID,
        /* Signed 8-bit value indicating the current RSSI */
        QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_RSSI,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX =
                QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_ndp_params - Used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_NDP.
 */
enum qca_wlan_vendor_attr_ndp_params {
        QCA_WLAN_VENDOR_ATTR_NDP_PARAM_INVALID = 0,
        /* Unsigned 32-bit value
         * enum of sub commands values in qca_wlan_ndp_sub_cmd
         */
        QCA_WLAN_VENDOR_ATTR_NDP_SUBCMD,
        /* Unsigned 16-bit value */
        QCA_WLAN_VENDOR_ATTR_NDP_TRANSACTION_ID,
        /* NL attributes for data used NDP SUB cmds */
        /* Unsigned 32-bit value indicating a service info */
        QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_INSTANCE_ID,
        /* Unsigned 32-bit value; channel frequency in MHz */
        QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL,
        /* Interface Discovery MAC address. An array of 6 Unsigned int8 */
        QCA_WLAN_VENDOR_ATTR_NDP_PEER_DISCOVERY_MAC_ADDR,
        /* Interface name on which NDP is being created */
        QCA_WLAN_VENDOR_ATTR_NDP_IFACE_STR,
        /* Unsigned 32-bit value for security */
        /* CONFIG_SECURITY is deprecated, use NCS_SK_TYPE/PMK/SCID instead */
        QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_SECURITY,
        /* Unsigned 32-bit value for QoS */
        QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_QOS,
        /* Array of u8: len = QCA_WLAN_VENDOR_ATTR_NAN_DP_APP_INFO_LEN */
        QCA_WLAN_VENDOR_ATTR_NDP_APP_INFO,
        /* Unsigned 32-bit value for NDP instance Id */
        QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID,
        /* Array of instance Ids */
        QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID_ARRAY,
        /* Unsigned 32-bit value for initiator/responder NDP response code
         * accept/reject
         */
        QCA_WLAN_VENDOR_ATTR_NDP_RESPONSE_CODE,
        /* NDI MAC address. An array of 6 Unsigned int8 */
        QCA_WLAN_VENDOR_ATTR_NDP_NDI_MAC_ADDR,
        /* Unsigned 32-bit value errors types returned by driver
         * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy
         * NanStatusType includes these values.
         */
        QCA_WLAN_VENDOR_ATTR_NDP_DRV_RESPONSE_STATUS_TYPE,
        /* Unsigned 32-bit value error values returned by driver
         * The nan_i.h in AOSP project platform/hardware/qcom/wlan
         * NanInternalStatusType includes these values.
         */
        QCA_WLAN_VENDOR_ATTR_NDP_DRV_RETURN_VALUE,
        /* Unsigned 32-bit value for Channel setup configuration
         * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy
         * NanDataPathChannelCfg includes these values.
         */
        QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_CONFIG,
        /* Unsigned 32-bit value for Cipher Suite Shared Key Type */
        QCA_WLAN_VENDOR_ATTR_NDP_CSID,
        /* Array of u8: len = NAN_PMK_INFO_LEN 32 bytes */
        QCA_WLAN_VENDOR_ATTR_NDP_PMK,
        /* Security Context Identifier that contains the PMKID
         * Array of u8: len = NAN_SCID_BUF_LEN 1024 bytes
         */
        QCA_WLAN_VENDOR_ATTR_NDP_SCID,
        /* Array of u8: len = NAN_SECURITY_MAX_PASSPHRASE_LEN 63 bytes */
        QCA_WLAN_VENDOR_ATTR_NDP_PASSPHRASE,
        /* Array of u8: len = NAN_MAX_SERVICE_NAME_LEN 255 bytes */
        QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_NAME,
        /* Unsigned 32-bit bitmap indicating schedule update
         * BIT_0: NSS Update
         * BIT_1: Channel list update
         */
        QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_REASON,
        /* Unsigned 32-bit value for NSS */
        QCA_WLAN_VENDOR_ATTR_NDP_NSS,
        /* Unsigned 32-bit value for NUMBER NDP CHANNEL */
        QCA_WLAN_VENDOR_ATTR_NDP_NUM_CHANNELS,
        /* Unsigned 32-bit value for CHANNEL BANDWIDTH
         * 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz
         */
        QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_WIDTH,
        /* Array of channel/band width */
        QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_INFO,
        /* IPv6 address used by NDP (in network byte order), 16 bytes array.
         * This attribute is used and optional for ndp request, ndp response,
         * ndp indication, and ndp confirm.
         */
        QCA_WLAN_VENDOR_ATTR_NDP_IPV6_ADDR = 27,
        /* Unsigned 16-bit value indicating transport port used by NDP.
         * This attribute is used and optional for ndp response, ndp indication,
         * and ndp confirm.
         */
        QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PORT = 28,
        /* Unsigned 8-bit value indicating protocol used by NDP and assigned by
         * the Internet Assigned Numbers Authority (IANA) as per:
         * https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml
         * This attribute is used and optional for ndp response, ndp indication,
         * and ndp confirm.
         */
        QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PROTOCOL = 29,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_MAX =
                QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST - 1,
};

enum qca_wlan_ndp_sub_cmd {
        QCA_WLAN_VENDOR_ATTR_NDP_INVALID = 0,
        /* Command to create a NAN data path interface */
        QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE = 1,
        /* Command to delete a NAN data path interface */
        QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE = 2,
        /* Command to initiate a NAN data path session */
        QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_REQUEST = 3,
        /* Command to notify if the NAN data path session was sent */
        QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_RESPONSE = 4,
        /* Command to respond to NAN data path session */
        QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_REQUEST = 5,
        /* Command to notify on the responder about the response */
        QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_RESPONSE = 6,
        /* Command to initiate a NAN data path end */
        QCA_WLAN_VENDOR_ATTR_NDP_END_REQUEST = 7,
        /* Command to notify the if end request was sent */
        QCA_WLAN_VENDOR_ATTR_NDP_END_RESPONSE = 8,
        /* Command to notify the peer about the end request */
        QCA_WLAN_VENDOR_ATTR_NDP_REQUEST_IND = 9,
        /* Command to confirm the NAN data path session is complete */
        QCA_WLAN_VENDOR_ATTR_NDP_CONFIRM_IND = 10,
        /* Command to indicate the peer about the end request being received */
        QCA_WLAN_VENDOR_ATTR_NDP_END_IND = 11,
        /* Command to indicate the peer of schedule update */
        QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_IND = 12
};

/**
 * enum qca_wlan_vendor_attr_nd_offload - Used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD.
 */
enum qca_wlan_vendor_attr_nd_offload {
        QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_INVALID = 0,
        /* Flag to set Neighbour Discovery offload */
        QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_FLAG,
        /* Keep last */
        QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_MAX =
                QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST - 1,
};

/**
 * enum packet_filter_sub_cmd - Packet filter sub commands
 */
enum packet_filter_sub_cmd {
        /**
         * Write packet filter program and/or data. The driver/firmware should
         * disable APF before writing into local buffer and re-enable APF after
         * writing is done.
         */
        QCA_WLAN_SET_PACKET_FILTER = 1,
        /* Get packet filter feature capabilities from driver */
        QCA_WLAN_GET_PACKET_FILTER = 2,
        /**
         * Write packet filter program and/or data. User space will send the
         * %QCA_WLAN_DISABLE_PACKET_FILTER command before issuing this command
         * and will send the %QCA_WLAN_ENABLE_PACKET_FILTER afterwards. The key
         * difference from that %QCA_WLAN_SET_PACKET_FILTER is the control over
         * enable/disable is given to user space with this command. Also,
         * user space sends the length of program portion in the buffer within
         * %QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH.
         */
        QCA_WLAN_WRITE_PACKET_FILTER = 3,
        /* Read packet filter program and/or data */
        QCA_WLAN_READ_PACKET_FILTER = 4,
        /* Enable APF feature */
        QCA_WLAN_ENABLE_PACKET_FILTER = 5,
        /* Disable APF feature */
        QCA_WLAN_DISABLE_PACKET_FILTER = 6,
};

/**
 * enum qca_wlan_vendor_attr_packet_filter - BPF control commands used by
 * vendor QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER.
 */
enum qca_wlan_vendor_attr_packet_filter {
        QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_INVALID = 0,
        /* Unsigned 32-bit enum passed using packet_filter_sub_cmd */
        QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SUB_CMD,
        /* Unsigned 32-bit value indicating the packet filter version */
        QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_VERSION,
        /* Unsigned 32-bit value indicating the packet filter id */
        QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_ID,
        /**
         * Unsigned 32-bit value indicating the packet filter size including
         * program + data.
         */
        QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SIZE,
        /* Unsigned 32-bit value indicating the packet filter current offset */
        QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_CURRENT_OFFSET,
        /* Program and/or data in bytes */
        QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROGRAM,
        /* Unsigned 32-bit value of the length of the program section in packet
         * filter buffer.
         */
        QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH = 7,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_MAX =
        QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_drv_info - WLAN driver info used by vendor command
 * QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE.
 */
enum qca_wlan_vendor_drv_info {
        QCA_WLAN_VENDOR_ATTR_DRV_INFO_INVALID = 0,
        /* Maximum Message size info between firmware & HOST
         * Unsigned 32-bit value
         */
        QCA_WLAN_VENDOR_ATTR_DRV_INFO_BUS_SIZE,
        /* keep last */
        QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_DRV_INFO_MAX =
                QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_wake_stats - Wake lock stats used by vendor
 * command QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS.
 */
enum qca_wlan_vendor_attr_wake_stats {
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_INVALID = 0,
        /* Unsigned 32-bit value indicating the total count of wake event */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_CMD_EVENT_WAKE,
        /* Array of individual wake count, each index representing wake reason
         */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_PTR,
        /* Unsigned 32-bit value representing wake count array */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_SZ,
        /* Unsigned 32-bit total wake count value of driver/fw */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_DRIVER_FW_LOCAL_WAKE,
        /* Array of wake stats of driver/fw */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_PTR,
        /* Unsigned 32-bit total wake count value of driver/fw */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_SZ,
        /* Unsigned 32-bit total wake count value of packets received */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_RX_DATA_WAKE,
        /* Unsigned 32-bit wake count value unicast packets received */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_UNICAST_CNT,
        /* Unsigned 32-bit wake count value multicast packets received */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_MULTICAST_CNT,
        /* Unsigned 32-bit wake count value broadcast packets received */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_BROADCAST_CNT,
        /* Unsigned 32-bit wake count value of ICMP packets */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP_PKT,
        /* Unsigned 32-bit wake count value of ICMP6 packets */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_PKT,
        /* Unsigned 32-bit value ICMP6 router advertisement */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RA,
        /* Unsigned 32-bit value ICMP6 neighbor advertisement */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NA,
        /* Unsigned 32-bit value ICMP6 neighbor solicitation */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NS,
        /* Unsigned 32-bit wake count value of receive side ICMP4 multicast */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP4_RX_MULTICAST_CNT,
        /* Unsigned 32-bit wake count value of receive side ICMP6 multicast */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RX_MULTICAST_CNT,
        /* Unsigned 32-bit wake count value of receive side multicast */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_OTHER_RX_MULTICAST_CNT,
        /* Unsigned 32-bit wake count value of a given RSSI breach */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RSSI_BREACH_CNT,
        /* Unsigned 32-bit wake count value of low RSSI */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_LOW_RSSI_CNT,
        /* Unsigned 32-bit value GSCAN count */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_GSCAN_CNT,
        /* Unsigned 32-bit value PNO complete count */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_COMPLETE_CNT,
        /* Unsigned 32-bit value PNO match count */
        QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_MATCH_CNT,
        /* keep last */
        QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST,
        QCA_WLAN_VENDOR_GET_WAKE_STATS_MAX =
                QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_thermal_cmd - Vendor subcmd attributes to set
 * cmd value. Used for NL attributes for data used by
 * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command.
 */
enum qca_wlan_vendor_attr_thermal_cmd {
        QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_INVALID = 0,
        /* The value of command, driver will implement different operations
         * according to this value. It uses values defined in
         * enum qca_wlan_vendor_attr_thermal_cmd_type.
         * u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE = 1,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_MAX =
        QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST - 1
};

/**
 * qca_wlan_vendor_attr_thermal_cmd_type: Attribute values for
 * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE to the vendor subcmd
 * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD. This represents the
 * thermal command types sent to driver.
 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS: Request to
 * get thermal shutdown configuration parameters for display. Parameters
 * responded from driver are defined in
 * enum qca_wlan_vendor_attr_get_thermal_params_rsp.
 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE: Request to
 * get temperature. Host should respond with a temperature data. It is defined
 * in enum qca_wlan_vendor_attr_thermal_get_temperature.
 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND: Request to execute thermal
 * suspend action.
 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME: Request to execute thermal
 * resume action.
 */
enum qca_wlan_vendor_attr_thermal_cmd_type {
        QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS,
        QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE,
        QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND,
        QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME,
};

/**
 * enum qca_wlan_vendor_attr_thermal_get_temperature - vendor subcmd attributes
 * to get chip temperature by user.
 * enum values are used for NL attributes for data used by
 * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE command for data used
 * by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command.
 */
enum qca_wlan_vendor_attr_thermal_get_temperature {
        QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_INVALID = 0,
        /* Temperature value (degree Celsius) from driver.
         * u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_DATA,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_MAX =
        QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_get_thermal_params_rsp - vendor subcmd attributes
 * to get configuration parameters of thermal shutdown feature. Enum values are
 * used by QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS command for data
 * used by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command.
 */
enum qca_wlan_vendor_attr_get_thermal_params_rsp {
        QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_INVALID = 0,
        /* Indicate if the thermal shutdown feature is enabled.
         * NLA_FLAG attribute.
         */
        QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_EN,
        /* Indicate if the auto mode is enabled.
         * Enable: Driver triggers the suspend/resume action.
         * Disable: User space triggers the suspend/resume action.
         * NLA_FLAG attribute.
         */
        QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_AUTO_EN,
        /* Thermal resume threshold (degree Celsius). Issue the resume command
         * if the temperature value is lower than this threshold.
         * u16 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_RESUME_THRESH,
        /* Thermal warning threshold (degree Celsius). FW reports temperature
         * to driver if it's higher than this threshold.
         * u16 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_WARNING_THRESH,
        /* Thermal suspend threshold (degree Celsius). Issue the suspend command
         * if the temperature value is higher than this threshold.
         * u16 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SUSPEND_THRESH,
        /* FW reports temperature data periodically at this interval (ms).
         * u16 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SAMPLE_RATE,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_MAX =
        QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_thermal_event - vendor subcmd attributes to
 * report thermal events from driver to user space.
 * enum values are used for NL attributes for data used by
 * QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT sub command.
 */
enum qca_wlan_vendor_attr_thermal_event {
        QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_INVALID = 0,
        /* Temperature value (degree Celsius) from driver.
         * u32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_TEMPERATURE,
        /* Indication of resume completion from power save mode.
         * NLA_FLAG attribute.
         */
        QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_RESUME_COMPLETE,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_MAX =
        QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST - 1,
};

/**
 * enum he_fragmentation_val - HE fragmentation support values
 * Indicates level of dynamic fragmentation that is supported by
 * a STA as a recipient.
 * HE fragmentation values are defined in IEEE P802.11ax/D2.0, 9.4.2.237.2
 * (HE MAC Capabilities Information field) and are used in HE Capabilities
 * element to advertise the support. These values are validated in the driver
 * to check the device capability and advertised in the HE Capabilities
 * element. These values are used to configure testbed device to allow the
 * advertised hardware capabilities to be downgraded for testing purposes.
 *
 * @HE_FRAG_DISABLE: no support for dynamic fragmentation
 * @HE_FRAG_LEVEL1: support for dynamic fragments that are
 *      contained within an MPDU or S-MPDU, no support for dynamic fragments
 *      within an A-MPDU that is not an S-MPDU.
 * @HE_FRAG_LEVEL2: support for dynamic fragments that are
 *      contained within an MPDU or S-MPDU and support for up to one dynamic
 *      fragment for each MSDU, each A-MSDU if supported by the recipient, and
 *      each MMPDU within an A-MPDU or multi-TID A-MPDU that is not an
 *      MPDU or S-MPDU.
 * @HE_FRAG_LEVEL3: support for dynamic fragments that are
 *      contained within an MPDU or S-MPDU and support for multiple dynamic
 *      fragments for each MSDU and for each A-MSDU if supported by the
 *      recipient within an A-MPDU or multi-TID AMPDU and up to one dynamic
 *      fragment for each MMPDU in a multi-TID A-MPDU that is not an S-MPDU.
 */
enum he_fragmentation_val {
        HE_FRAG_DISABLE,
        HE_FRAG_LEVEL1,
        HE_FRAG_LEVEL2,
        HE_FRAG_LEVEL3,
};

/**
 * enum he_mcs_config - HE MCS support configuration
 *
 * Configures the HE Tx/Rx MCS map in HE capability IE for given bandwidth.
 * These values are used in driver to configure the HE MCS map to advertise
 * Tx/Rx MCS map in HE capability and these values are applied for all the
 * streams supported by the device. To configure MCS for different bandwidths,
 * vendor command needs to be sent using this attribute with appropriate value.
 * For example, to configure HE_80_MCS_0_7, send vendor command using HE MCS
 * attribute with HE_80_MCS0_7. And to configure HE MCS for HE_160_MCS0_11
 * send this command using HE MCS config attribute with value HE_160_MCS0_11.
 * These values are used to configure testbed device to allow the advertised
 * hardware capabilities to be downgraded for testing purposes. The enum values
 * are defined such that BIT[1:0] indicates the MCS map value. Values 3,7 and
 * 11 are not used as BIT[1:0] value is 3 which is used to disable MCS map.
 * These values are validated in the driver before setting the MCS map and
 * driver returns error if the input is other than these enum values.
 *
 * @HE_80_MCS0_7: support for HE 80/40/20 MHz MCS 0 to 7
 * @HE_80_MCS0_9: support for HE 80/40/20 MHz MCS 0 to 9
 * @HE_80_MCS0_11: support for HE 80/40/20 MHz MCS 0 to 11
 * @HE_160_MCS0_7: support for HE 160 MHz MCS 0 to 7
 * @HE_160_MCS0_9: support for HE 160 MHz MCS 0 to 9
 * @HE_160_MCS0_11: support for HE 160 MHz MCS 0 to 11
 * @HE_80P80_MCS0_7: support for HE 80p80 MHz MCS 0 to 7
 * @HE_80P80_MCS0_9: support for HE 80p80 MHz MCS 0 to 9
 * @HE_80P80_MCS0_11: support for HE 80p80 MHz MCS 0 to 11
 */
enum he_mcs_config {
        HE_80_MCS0_7 = 0,
        HE_80_MCS0_9 = 1,
        HE_80_MCS0_11 = 2,
        HE_160_MCS0_7 = 4,
        HE_160_MCS0_9 = 5,
        HE_160_MCS0_11 = 6,
        HE_80P80_MCS0_7 = 8,
        HE_80P80_MCS0_9 = 9,
        HE_80P80_MCS0_11 = 10,
};

/**
 * enum qca_wlan_ba_session_config - BA session configuration
 *
 * Indicates the configuration values for BA session configuration attribute.
 *
 * @QCA_WLAN_ADD_BA: Establish a new BA session with given configuration.
 * @QCA_WLAN_DELETE_BA: Delete the existing BA session for given TID.
 */
enum qca_wlan_ba_session_config {
        QCA_WLAN_ADD_BA = 1,
        QCA_WLAN_DELETE_BA = 2,
};

/**
 * enum qca_wlan_ac_type - Access category type
 *
 * Indicates the access category type value.
 *
 * @QCA_WLAN_AC_BE: BE access category
 * @QCA_WLAN_AC_BK: BK access category
 * @QCA_WLAN_AC_VI: VI access category
 * @QCA_WLAN_AC_VO: VO access category
 * @QCA_WLAN_AC_ALL: All ACs
 */
enum qca_wlan_ac_type {
        QCA_WLAN_AC_BE = 0,
        QCA_WLAN_AC_BK = 1,
        QCA_WLAN_AC_VI = 2,
        QCA_WLAN_AC_VO = 3,
        QCA_WLAN_AC_ALL = 4,
};

/**
 * enum qca_wlan_he_ltf_cfg - HE LTF configuration
 *
 * Indicates the HE LTF configuration value.
 *
 * @QCA_WLAN_HE_LTF_AUTO: HE-LTF is automatically set to the mandatory HE-LTF,
 * based on the GI setting
 * @QCA_WLAN_HE_LTF_1X: 1X HE LTF is 3.2us LTF
 * @QCA_WLAN_HE_LTF_2X: 2X HE LTF is 6.4us LTF
 * @QCA_WLAN_HE_LTF_4X: 4X HE LTF is 12.8us LTF
 */
enum qca_wlan_he_ltf_cfg {
        QCA_WLAN_HE_LTF_AUTO = 0,
        QCA_WLAN_HE_LTF_1X = 1,
        QCA_WLAN_HE_LTF_2X = 2,
        QCA_WLAN_HE_LTF_4X = 3,
};

/**
 * enum qca_wlan_he_mac_padding_dur - HE trigger frame MAC padding duration
 *
 * Indicates the HE trigger frame MAC padding duration value.
 *
 * @QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME: no additional time required to
 * process the trigger frame.
 * @QCA_WLAN_HE_8US_OF_PROCESS_TIME: indicates the 8us of processing time for
 * trigger frame.
 * @QCA_WLAN_HE_16US_OF_PROCESS_TIME: indicates the 16us of processing time for
 * trigger frame.
 */
enum qca_wlan_he_mac_padding_dur {
        QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME = 0,
        QCA_WLAN_HE_8US_OF_PROCESS_TIME = 1,
        QCA_WLAN_HE_16US_OF_PROCESS_TIME = 2,
};

/* Attributes for data used by
 * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION
 */
enum qca_wlan_vendor_attr_wifi_test_config {
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_INVALID = 0,
        /* 8-bit unsigned value to configure the driver to enable/disable
         * WMM feature. This attribute is used to configure testbed device.
         * 1-enable, 0-disable
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WMM_ENABLE = 1,

        /* 8-bit unsigned value to configure the driver to accept/reject
         * the addba request from peer. This attribute is used to configure
         * the testbed device.
         * 1-accept addba, 0-reject addba
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ACCEPT_ADDBA_REQ = 2,

        /* 8-bit unsigned value to configure the driver to send or not to
         * send the addba request to peer.
         * This attribute is used to configure the testbed device.
         * 1-send addba, 0-do not send addba
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SEND_ADDBA_REQ = 3,

        /* 8-bit unsigned value to indicate the HE fragmentation support.
         * Uses enum he_fragmentation_val values.
         * This attribute is used to configure the testbed device to
         * allow the advertised hardware capabilities to be downgraded
         * for testing purposes.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_FRAGMENTATION = 4,

        /* 8-bit unsigned value to indicate the HE MCS support.
         * Uses enum he_mcs_config values.
         * This attribute is used to configure the testbed device to
         * allow the advertised hardware capabilities to be downgraded
         * for testing purposes.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MCS = 5,

        /* 8-bit unsigned value to configure the driver to allow or not to
         * allow the connection with WEP/TKIP in HT/VHT/HE modes.
         * This attribute is used to configure the testbed device.
         * 1-allow WEP/TKIP in HT/VHT/HE, 0-do not allow WEP/TKIP.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WEP_TKIP_IN_HE = 6,

        /* 8-bit unsigned value to configure the driver to add a
         * new BA session or delete the existing BA session for
         * given TID. ADDBA command uses the buffer size and TID
         * configuration if user specifies the values else default
         * value for buffer size is used for all TIDs if the TID
         * also not specified. For DEL_BA command TID value is
         * required to process the command.
         * Uses enum qca_wlan_ba_session_config values.
         * This attribute is used to configure the testbed device.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADD_DEL_BA_SESSION = 7,

        /* 16-bit unsigned value to configure the buffer size in addba
         * request and response frames.
         * This attribute is used to configure the testbed device.
         * The range of the value is 0 to 256.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADDBA_BUFF_SIZE = 8,

        /* 8-bit unsigned value to configure the buffer size in addba
         * request and response frames.
         * This attribute is used to configure the testbed device.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BA_TID = 9,

        /* 8-bit unsigned value to configure the no ack policy.
         * To configure no ack policy, access category value is
         * required to process the command.
         * This attribute is used to configure the testbed device.
         * 1 - enable no ack, 0 - disable no ack.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_NO_ACK = 10,

        /* 8-bit unsigned value to configure the AC for no ack policy
         * This attribute is used to configure the testbed device.
         * Uses the enum qca_wlan_ac_type values.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_NO_ACK_AC = 11,

        /* 8-bit unsigned value to configure the HE LTF
         * This attribute is used to configure the testbed device.
         * Uses the enum qca_wlan_he_ltf_cfg values.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_LTF = 12,

        /* 8-bit unsigned value to configure the tx beamformee.
         * This attribute is used to configure the testbed device.
         * 1-enable, 0-disable.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_TX_BEAMFORMEE = 13,

        /* 8-bit unsigned value to configure the tx beamformee number
         * of space-time streams.
         * This attribute is used to configure the testbed device.
         * The range of the value is 0 to 8.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_BEAMFORMEE_NSTS = 14,

        /* 8-bit unsigned value to configure the MU EDCA params for given AC
         * This attribute is used to configure the testbed device.
         * Uses the enum qca_wlan_ac_type values.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AC = 15,

        /* 8-bit unsigned value to configure the MU EDCA AIFSN for given AC
         * To configure MU EDCA AIFSN value, MU EDCA access category value
         * is required to process the command.
         * This attribute is used to configure the testbed device.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AIFSN = 16,

        /* 8-bit unsigned value to configure the MU EDCA ECW min value for
         * given AC.
         * To configure MU EDCA ECW min value, MU EDCA access category value
         * is required to process the command.
         * This attribute is used to configure the testbed device.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMIN = 17,

        /* 8-bit unsigned value to configure the MU EDCA ECW max value for
         * given AC.
         * To configure MU EDCA ECW max value, MU EDCA access category value
         * is required to process the command.
         * This attribute is used to configure the testbed device.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMAX = 18,

        /* 8-bit unsigned value to configure the MU EDCA timer for given AC
         * To configure MU EDCA timer value, MU EDCA access category value
         * is required to process the command.
         * This attribute is used to configure the testbed device.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_TIMER = 19,

        /* 8-bit unsigned value to configure the HE trigger frame MAC padding
         * duration.
         * This attribute is used to configure the testbed device.
         * Uses the enum qca_wlan_he_mac_padding_dur values.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MAC_PADDING_DUR = 20,

        /* 8-bit unsigned value to override the MU EDCA params to defaults
         * regardless of the AP beacon MU EDCA params. If it is enabled use
         * the default values else use the MU EDCA params from AP beacon.
         * This attribute is used to configure the testbed device.
         * 1-enable, 0-disable.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OVERRIDE_MU_EDCA = 21,

        /* 8-bit unsigned value to configure the support for receiving
         * an MPDU that contains an operating mode control subfield.
         * This attribute is used to configure the testbed device.
         * 1-enable, 0-disable.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_SUPP = 22,

        /* Nested attribute values required to setup the TWT session.
         * enum qca_wlan_vendor_attr_twt_setup provides the necessary
         * information to set up the session. It contains broadcast flags,
         * set_up flags, trigger value, flow type, flow ID, wake interval
         * exponent, protection, target wake time, wake duration, wake interval
         * mantissa. These nested attributes are used to setup a host triggered
         * TWT session.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP = 23,

        /* This nested attribute is used to terminate the current TWT session.
         * It does not currently carry any attributes.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_TERMINATE = 24,

        /* This nested attribute is used to suspend the current TWT session.
         * It does not currently carry any attributes.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SUSPEND = 25,

        /* Nested attribute values to indicate the request for resume.
         * This attribute is used to resume the TWT session.
         * enum qca_wlan_vendor_attr_twt_resume provides the necessary
         * parameters required to resume the TWT session.
         */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME = 26,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_MAX =
        QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_bss_filter - Used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
 * The user can add/delete the filter by specifying the BSSID/STA MAC address in
 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, filter type in
 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, add/delete action in
 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user can get the
 * statistics of an unassociated station by specifying the MAC address in
 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, station type in
 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, GET action in
 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user also can get
 * the statistics of all unassociated stations by specifying the Broadcast MAC
 * address (ff:ff:ff:ff:ff:ff) in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR with
 * above procedure. In the response, driver shall specify statistics
 * information nested in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS.
 */
enum qca_wlan_vendor_attr_bss_filter {
        QCA_WLAN_VENDOR_ATTR_BSS_FILTER_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR = 1,
        /* Other BSS filter type, unsigned 8 bit value. One of the values
         * in enum qca_wlan_vendor_bss_filter_type.
         */
        QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE = 2,
        /* Other BSS filter action, unsigned 8 bit value. One of the values
         * in enum qca_wlan_vendor_bss_filter_action.
         */
        QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION = 3,
        /* Array of nested attributes where each entry is the statistics
         * information of the specified station that belong to another BSS.
         * Attributes for each entry are taken from enum
         * qca_wlan_vendor_bss_filter_sta_stats.
         * Other BSS station configured in
         * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER with filter type
         * QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA.
         * Statistics returned by QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER
         * with filter action QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET.
         */
        QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS = 4,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAX =
        QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_bss_filter_type - Type of
 * filter used in other BSS filter operations. Used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
 *
 * @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID: BSSID filter
 * @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA: Station MAC address filter
 */
enum qca_wlan_vendor_bss_filter_type {
        QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID,
        QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA,
};

/**
 * enum qca_wlan_vendor_bss_filter_action - Type of
 * action in other BSS filter operations. Used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
 *
 * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD: Add filter
 * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL: Delete filter
 * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET: Get the statistics
 */
enum qca_wlan_vendor_bss_filter_action {
        QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD,
        QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL,
        QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET,
};

/**
 * enum qca_wlan_vendor_bss_filter_sta_stats - Attributes for
 * the statistics of a specific unassociated station belonging to another BSS.
 * The statistics provides information of the unassociated station
 * filtered by other BSS operation - such as MAC, signal value.
 * Used by the vendor command QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
 *
 * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC: MAC address of the station.
 * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI: Last received signal strength
 *      of the station. Unsigned 8 bit number containing RSSI.
 * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS: Time stamp of the host
 *      driver for the last received RSSI. Unsigned 64 bit number containing
 *      nanoseconds from the boottime.
 */
enum qca_wlan_vendor_bss_filter_sta_stats {
        QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_INVALID = 0,
        QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC = 1,
        QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI = 2,
        QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS = 3,

        /* keep last */
        QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST,
        QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAX =
        QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST - 1
};

/* enum qca_wlan_nan_subcmd_type - Type of NAN command used by attribute
 * QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE as a part of vendor command
 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT.
 */
enum qca_wlan_nan_ext_subcmd_type {
        /* Subcmd of type NAN Enable Request */
        QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ = 1,
        /* Subcmd of type NAN Disable Request */
        QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ = 2,
};

/**
 * enum qca_wlan_vendor_attr_nan_params - Used by the vendor command
 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT.
 */
enum qca_wlan_vendor_attr_nan_params {
        QCA_WLAN_VENDOR_ATTR_NAN_INVALID = 0,
        /* Carries NAN command for firmware component. Every vendor command
         * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT must contain this attribute with a
         * payload containing the NAN command. NLA_BINARY attribute.
         */
        QCA_WLAN_VENDOR_ATTR_NAN_CMD_DATA = 1,
        /* Indicates the type of NAN command sent with
         * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. enum qca_wlan_nan_ext_subcmd_type
         * describes the possible range of values. This attribute is mandatory
         * if the command being issued is either
         * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ or
         * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ. NLA_U32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE = 2,
        /* Frequency (in MHz) of primary NAN discovery social channel in 2.4 GHz
         * band. This attribute is mandatory when command type is
         * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ. NLA_U32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_NAN_DISC_24GHZ_BAND_FREQ = 3,
        /* Frequency (in MHz) of secondary NAN discovery social channel in 5 GHz
         * band. This attribute is optional and should be included when command
         * type is QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ and NAN discovery
         * has to be started on 5GHz along with 2.4GHz. NLA_U32 attribute.
         */
        QCA_WLAN_VENDOR_ATTR_NAN_DISC_5GHZ_BAND_FREQ = 4,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_MAX =
                QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST - 1
};

/**
 * enum qca_wlan_vendor_attr_twt_setup: Represents attributes for
 * TWT (Target Wake Time) setup request. These attributes are sent as part of
 * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP and
 * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION.
 *
 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST: Flag attribute.
 * Disable (flag attribute not present) - Individual TWT
 * Enable (flag attribute present) - Broadcast TWT.
 * Individual means the session is between the STA and the AP.
 * This session is established using a separate negotiation between
 * STA and AP.
 * Broadcast means the session is across multiple STAs and an AP. The
 * configuration parameters are announced in Beacon frames by the AP.
 *
 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE: Required (u8).
 * Unsigned 8-bit qca_wlan_vendor_twt_setup_req_type to
 * specify the TWT request type
 *
 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER: Flag attribute
 * Enable (flag attribute present) - TWT with trigger support.
 * Disable (flag attribute not present) - TWT without trigger support.
 * Trigger means the AP will send the trigger frame to allow STA to send data.
 * Without trigger, the STA will wait for the MU EDCA timer before
 * transmitting the data.
 *
 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE: Required (u8)
 * 0 - Announced TWT - In this mode, STA may skip few service periods to
 * save more power. If STA wants to wake up, it will send a PS-POLL/QoS
 * NULL frame to AP.
 * 1 - Unannounced TWT - The STA will wakeup during every SP.
 *
 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID: Optional (u8)
 * Flow ID is the unique identifier for each TWT session.
 * Currently this is not required and dialog ID will be set to zero.
 *
 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP: Required (u8)
 * This attribute (exp) is used along with the mantissa to derive the
 * wake interval using the following formula:
 * pow(2,exp) = wake_intvl_us/wake_intvl_mantis
 * Wake interval is the interval between 2 successive SP.
 *
 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION: Flag attribute
 * Enable (flag attribute present) - Protection required.
 * Disable (flag attribute not present) - Protection not required.
 * If protection is enabled, then the AP will use protection
 * mechanism using RTS/CTS to self to reserve the airtime.
 *
 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME: Optional (u32)
 * This attribute is used as the SP offset which is the offset from
 * TSF after which the wake happens. The units are in microseconds. If
 * this attribute is not provided, then the value will be set to zero.
 *
 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION: Required (u32)
 * This is the duration of the service period. The units are in TU.
 *
 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA: Required (u32)
 * This attribute is used to configure wake interval mantissa.
 * The units are in TU.
 */
enum qca_wlan_vendor_attr_twt_setup {
        QCA_WLAN_VENDOR_ATTR_TWT_SETUP_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST = 1,
        QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE = 2,
        QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER = 3,
        QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE = 4,
        QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID = 5,
        QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP = 6,
        QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION = 7,
        QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME = 8,
        QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION = 9,
        QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA = 10,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX =
        QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_attr_twt_resume: Represents attributes for
 * TWT (Target Wake Time) resume request. These attributes are sent as part of
 * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME and
 * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION.
 *
 * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT: Optional (u8)
 * This attribute is used as the SP offset which is the offset from
 * TSF after which the wake happens. The units are in microseconds.
 * If this attribute is not provided, then the value will be set to
 * zero.
 *
 * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE: Required (u32)
 * This attribute represents the next TWT subfield size.
 */
enum qca_wlan_vendor_attr_twt_resume {
        QCA_WLAN_VENDOR_ATTR_TWT_RESUME_INVALID = 0,
        QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT = 1,
        QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE = 2,

        /* keep last */
        QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST,
        QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAX =
        QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST - 1,
};

/**
 * enum qca_wlan_vendor_twt_setup_req_type - Required (u8)
 * Represents the setup type being requested for TWT.
 * @QCA_WLAN_VENDOR_TWT_SETUP_REQUEST: STA is not specifying all the TWT
 * parameters but relying on AP to fill the parameters during the negotiation.
 * @QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST: STA will provide all the suggested
 * values which the AP may accept or AP may provide alternative parameters
 * which the STA may accept.
 * @QCA_WLAN_VENDOR_TWT_SETUP_DEMAND: STA is not willing to accept any
 * alternate parameters than the requested ones.
 */
enum qca_wlan_vendor_twt_setup_req_type {
        QCA_WLAN_VENDOR_TWT_SETUP_REQUEST = 1,
        QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST = 2,
        QCA_WLAN_VENDOR_TWT_SETUP_DEMAND = 3,
};

#endif /* QCA_VENDOR_H */