/*
* Qualcomm Atheros OUI and vendor specific assignments
* Copyright (c) 2014-2017, Qualcomm Atheros, Inc.
- * Copyright (c) 2018, The Linux Foundation
+ * Copyright (c) 2018-2019, The Linux Foundation
*
* This software may be distributed under the terms of the BSD license.
* See README for more details.
#define OUI_QCA 0x001374
+#ifndef BIT
+#define BIT(x) (1U << (x))
+#endif
+
/**
* enum qca_radiotap_vendor_ids - QCA radiotap vendor namespace IDs
*/
*
* @QCA_NL80211_VENDOR_SUBCMD_DO_ACS: ACS command/event which is used to
* invoke the ACS function in device and pass selected channels to
- * hostapd.
+ * hostapd. Uses enum qca_wlan_vendor_attr_acs_offload attributes.
*
* @QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES: Command to get the features
* supported by the driver. enum qca_wlan_vendor_features defines
* which supports DFS offloading, to indicate a radar pattern has been
* detected. The channel is now unusable.
*
+ * @QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO: Get information from the driver.
+ * Attributes defined in enum qca_wlan_vendor_attr_get_wifi_info.
+ *
* @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: Get the feature bitmap
* based on enum wifi_logger_supported_features. Attributes defined in
* enum qca_wlan_vendor_attr_get_logger_features.
* to notify the connected station's status. The attributes for this
* command are defined in enum qca_wlan_vendor_attr_link_properties.
*
+ * @QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY: This command is used to configure
+ * DFS policy and channel hint for ACS operation. This command uses the
+ * attributes defined in enum qca_wlan_vendor_attr_acs_config and
+ * enum qca_acs_dfs_mode.
+ *
* @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to
* start the P2P Listen offload function in device and pass the listen
* channel, period, interval, count, device types, and vendor specific
* @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START: Start spectral scan. The scan
* parameters are specified by enum qca_wlan_vendor_attr_spectral_scan.
* This returns a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE)
- * identifying the operation in success case.
+ * identifying the operation in success case. In failure cases an
+ * error code (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_ERROR_CODE)
+ * describing the reason for the failure is returned.
*
* @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP: Stop spectral scan. This uses
* a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) from
* parameters including Zigbee state and specific WLAN periods to enhance
* PTA master. All these parameters are delivered by the attributes
* defined in enum qca_mpta_helper_vendor_attr.
+ * @QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING: This sub command is used to
+ * implement Beacon frame reporting feature.
+ *
+ * Userspace can request the driver/firmware to periodically report
+ * received Beacon frames whose BSSID is same as the current connected
+ * BSS's MAC address.
+ *
+ * In case the STA seamlessly (without sending disconnect indication to
+ * userspace) roams to a different BSS, Beacon frame reporting will be
+ * automatically enabled for the Beacon frames whose BSSID is same as the
+ * MAC address of the new BSS. Beacon reporting will be stopped when the
+ * STA is disconnected (when the disconnect indication is sent to
+ * userspace) and need to be explicitly enabled by userspace for next
+ * connection.
+ *
+ * When a Beacon frame matching configured conditions is received, and if
+ * userspace has requested to send asynchronous beacon reports, the
+ * driver/firmware will encapsulate the details of the Beacon frame in an
+ * event and send it to userspace along with updating the BSS information
+ * in cfg80211 scan cache, otherwise driver will only update the cfg80211
+ * scan cache with the information from the received Beacon frame but will
+ * not send any active report to userspace.
+ *
+ * The userspace can request the driver/firmware to stop reporting Beacon
+ * frames. If the driver/firmware is not able to receive Beacon frames due
+ * to other Wi-Fi operations such as off-channel activities, etc., the
+ * driver/firmware will send a pause event to userspace and stop reporting
+ * Beacon frames. Whether the beacon reporting will be automatically
+ * resumed or not by the driver/firmware later will be reported to
+ * userspace using the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES
+ * flag. The beacon reporting shall be resumed for all the cases except
+ * either when userspace sets
+ * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_DO_NOT_RESUME flag in the command
+ * which triggered the current beacon reporting or during any disconnection
+ * case as indicated by setting
+ * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PAUSE_REASON to
+ * QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_DISCONNECTED by the
+ * driver.
+ *
+ * After QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_PAUSE event is received
+ * by userspace with QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES
+ * flag not set, the next first
+ * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO event from the driver
+ * shall be considered as un-pause event.
+ *
+ * All the attributes used with this command are defined in
+ * enum qca_wlan_vendor_attr_beacon_reporting_params.
+ * @QCA_NL80211_VENDOR_SUBCMD_INTEROP_ISSUES_AP: In practice, some APs have
+ * interop issues with the DUT. This sub command is used to transfer the
+ * AP info between the driver and user space. This works both as a command
+ * and an event. As a command, it configures the stored list of APs from
+ * user space to firmware; as an event, it indicates the AP info detected
+ * by the firmware to user space for persistent storage. The attributes
+ * defined in enum qca_vendor_attr_interop_issues_ap are used to deliver
+ * the parameters.
+ * @QCA_NL80211_VENDOR_SUBCMD_OEM_DATA: This command/event is used to
+ * send/receive OEM data binary blobs to/from application/service to/from
+ * firmware. The attributes defined in enum
+ * qca_wlan_vendor_attr_oem_data_params are used to deliver the
+ * parameters.
+ * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT: This command/event is used
+ * to send/receive avoid frequency data using
+ * enum qca_wlan_vendor_attr_avoid_frequency_ext.
+ * This new command is alternative to existing command
+ * QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY since existing command/event
+ * is using stream of bytes instead of structured data using vendor
+ * attributes.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE: This vendor subcommand is used to
+ * add the STA node details in driver/firmware. Attributes for this event
+ * are specified in enum qca_wlan_vendor_attr_add_sta_node_params.
+ * @QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE: This command is used to set BT
+ * coex chain mode from application/service.
+ * The attributes defined in enum qca_vendor_attr_btc_chain_mode are used
+ * to deliver the parameters.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO: This vendor subcommand is used to
+ * get information of a station from driver to userspace. This command can
+ * be used in both STA and AP modes. For STA mode, it provides information
+ * of the current association when in connected state or the last
+ * association when in disconnected state. For AP mode, only information
+ * of the currently connected stations is available. This command uses
+ * attributes defined in enum qca_wlan_vendor_attr_get_sta_info.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_REQUEST_SAR_LIMITS_EVENT: This acts as an event.
+ * Host drivers can request the user space entity to set the SAR power
+ * limits with this event. Accordingly, the user space entity is expected
+ * to set the SAR power limits. Host drivers can retry this event to the
+ * user space for the SAR power limits configuration from user space. If
+ * the driver does not get the SAR power limits from user space for all
+ * the retried attempts, it can configure a default SAR power limit.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO: This acts as a vendor event and
+ * is used to update the information about the station from the driver to
+ * userspace. Uses attributes from enum
+ * qca_wlan_vendor_attr_update_sta_info.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_DRIVER_DISCONNECT_REASON: This acts as an event.
+ * The host driver initiates the disconnection for scenarios such as beacon
+ * miss, NUD failure, peer kick out, etc. The disconnection indication
+ * through cfg80211_disconnected() expects the reason codes from enum
+ * ieee80211_reasoncode which does not signify these various reasons why
+ * the driver has triggered the disconnection. This event will be used to
+ * send the driver specific reason codes by the host driver to userspace.
+ * Host drivers should trigger this event and pass the respective reason
+ * code immediately prior to triggering cfg80211_disconnected(). The
+ * attributes used with this event are defined in enum
+ * qca_wlan_vendor_attr_driver_disconnect_reason.
*/
enum qca_nl80211_vendor_subcmds {
QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0,
QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE = 109,
/* 110..114 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB = 115,
- /* 116..117 - reserved for QCA */
+ QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY = 116,
+ /* 117 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG = 118,
QCA_NL80211_VENDOR_SUBCMD_TSF = 119,
QCA_NL80211_VENDOR_SUBCMD_WISA = 120,
QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE = 177,
QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH = 178,
QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG = 179,
+ QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING = 180,
+ QCA_NL80211_VENDOR_SUBCMD_INTEROP_ISSUES_AP = 181,
+ QCA_NL80211_VENDOR_SUBCMD_OEM_DATA = 182,
+ QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT = 183,
+ QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE = 184,
+ QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE = 185,
+ QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO = 186,
+ QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS_EVENT = 187,
+ QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO = 188,
+ QCA_NL80211_VENDOR_SUBCMD_DRIVER_DISCONNECT_REASON = 189,
};
enum qca_wlan_vendor_attr {
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST - 1
};
+/**
+ * enum qca_wlan_vendor_attr_acs_offload - Defines attributes to be used with
+ * vendor command/event QCA_NL80211_VENDOR_SUBCMD_DO_ACS.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL: Required (u8).
+ * Used with event to notify the primary channel number selected in ACS
+ * operation.
+ * Note: If both the driver and user-space application supports the 6 GHz band,
+ * QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL is deprecated; use
+ * QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY instead.
+ * To maintain backward compatibility, QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL
+ * is still used if either of the driver or user space application doesn't
+ * support the 6 GHz band.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL: Required (u8).
+ * Used with event to notify the secondary channel number selected in ACS
+ * operation.
+ * Note: If both the driver and user-space application supports the 6 GHz band,
+ * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL is deprecated; use
+ * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY instead.
+ * To maintain backward compatibility,
+ * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL is still used if either of
+ * the driver or user space application doesn't support 6 GHz band.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE: Required (u8).
+ * (a) Used with command to configure hw_mode from
+ * enum qca_wlan_vendor_acs_hw_mode for ACS operation.
+ * (b) Also used with event to notify the hw_mode of selected primary channel
+ * in ACS operation.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED: Flag attribute.
+ * Used with command to configure ACS operation for HT mode.
+ * Disable (flag attribute not present) - HT disabled and
+ * Enable (flag attribute present) - HT enabled.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED: Flag attribute.
+ * Used with command to configure ACS operation for HT40 mode.
+ * Disable (flag attribute not present) - HT40 disabled and
+ * Enable (flag attribute present) - HT40 enabled.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED: Flag attribute.
+ * Used with command to configure ACS operation for VHT mode.
+ * Disable (flag attribute not present) - VHT disabled and
+ * Enable (flag attribute present) - VHT enabled.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH: Optional (u16) with command and
+ * mandatory with event.
+ * If specified in command path, ACS operation is configured with the given
+ * channel width (in MHz).
+ * In event path, specifies the channel width of the primary channel selected.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST: Required and type is NLA_UNSPEC.
+ * Used with command to configure channel list using an array of
+ * channel numbers (u8).
+ * Note: If both the driver and user-space application supports the 6 GHz band,
+ * the driver mandates use of QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST whereas
+ * QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST is optional.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL: Required (u8).
+ * Used with event to notify the VHT segment 0 center channel number selected in
+ * ACS operation. The value is the index of the channel center frequency for
+ * 20 MHz, 40 MHz, and 80 MHz channels. The value is the center frequency index
+ * of the primary 80 MHz segment for 160 MHz and 80+80 MHz channels.
+ * Note: If both the driver and user-space application supports the 6 GHz band,
+ * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL is deprecated; use
+ * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_FREQUENCY instead.
+ * To maintain backward compatibility,
+ * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL is still used if either of
+ * the driver or user space application doesn't support the 6 GHz band.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL: Required (u8).
+ * Used with event to notify the VHT segment 1 center channel number selected in
+ * ACS operation. The value is zero for 20 MHz, 40 MHz, and 80 MHz channels.
+ * The value is the index of the channel center frequency for 160 MHz channels
+ * and the center frequency index of the secondary 80 MHz segment for 80+80 MHz
+ * channels.
+ * Note: If both the driver and user-space application supports the 6 GHz band,
+ * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL is deprecated; use
+ * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_FREQUENCY instead.
+ * To maintain backward compatibility,
+ * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL is still used if either of
+ * the driver or user space application doesn't support the 6 GHz band.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST: Required and type is NLA_UNSPEC.
+ * Used with command to configure the channel list using an array of channel
+ * center frequencies in MHz (u32).
+ * Note: If both the driver and user-space application supports the 6 GHz band,
+ * the driver first parses the frequency list and if it fails to get a frequency
+ * list, parses the channel list specified using
+ * QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST (considers only 2 GHz and 5 GHz channels in
+ * QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST).
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY: Required (u32).
+ * Used with event to notify the primary channel center frequency (MHz) selected
+ * in ACS operation.
+ * Note: If the driver supports the 6 GHz band, the event sent from the driver
+ * includes this attribute along with QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY: Required (u32).
+ * Used with event to notify the secondary channel center frequency (MHz)
+ * selected in ACS operation.
+ * Note: If the driver supports the 6 GHz band, the event sent from the driver
+ * includes this attribute along with
+ * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_FREQUENCY: Required (u32).
+ * Used with event to notify the VHT segment 0 center channel frequency (MHz)
+ * selected in ACS operation.
+ * Note: If the driver supports the 6 GHz band, the event sent from the driver
+ * includes this attribute along with
+ * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_FREQUENCY: Required (u32).
+ * Used with event to notify the VHT segment 1 center channel frequency (MHz)
+ * selected in ACS operation.
+ * Note: If the driver supports the 6 GHz band, the event sent from the driver
+ * includes this attribute along with
+ * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED: Flag attribute.
+ * Used with command to notify the driver of EDMG request for ACS
+ * operation.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_EDMG_CHANNEL: Optional (u8).
+ * Used with event to notify the EDMG channel number selected in ACS
+ * operation.
+ * EDMG primary channel is indicated by QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL
+ */
enum qca_wlan_vendor_attr_acs_offload {
QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID = 0,
- QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL,
- QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL,
- QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE,
- QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED,
- QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED,
- QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED,
- QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH,
- QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST,
- QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL,
- QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL,
- QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST,
+ QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL = 1,
+ QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL = 2,
+ QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE = 3,
+ QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED = 4,
+ QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED = 5,
+ QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED = 6,
+ QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH = 7,
+ QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST = 8,
+ QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL = 9,
+ QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL = 10,
+ QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST = 11,
+ QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY = 12,
+ QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY = 13,
+ QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_FREQUENCY = 14,
+ QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_FREQUENCY = 15,
+ QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED = 16,
+ QCA_WLAN_VENDOR_ATTR_ACS_EDMG_CHANNEL = 17,
+
/* keep last */
QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_ACS_MAX =
QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST - 1
};
+/**
+ * enum qca_wlan_vendor_acs_hw_mode - Defines HW mode to be used with the
+ * vendor command/event QCA_NL80211_VENDOR_SUBCMD_DO_ACS.
+ *
+ * @QCA_ACS_MODE_IEEE80211B: 802.11b mode
+ * @QCA_ACS_MODE_IEEE80211G: 802.11g mode
+ * @QCA_ACS_MODE_IEEE80211A: 802.11a mode
+ * @QCA_ACS_MODE_IEEE80211AD: 802.11ad mode
+ * @QCA_ACS_MODE_IEEE80211ANY: all modes
+ * @QCA_ACS_MODE_IEEE80211AX: 802.11ax mode
+ */
enum qca_wlan_vendor_acs_hw_mode {
QCA_ACS_MODE_IEEE80211B,
QCA_ACS_MODE_IEEE80211G,
QCA_ACS_MODE_IEEE80211A,
QCA_ACS_MODE_IEEE80211AD,
QCA_ACS_MODE_IEEE80211ANY,
+ QCA_ACS_MODE_IEEE80211AX,
};
/**
* @QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY: Device supports self
* managed regulatory.
* @QCA_WLAN_VENDOR_FEATURE_TWT: Device supports TWT (Target Wake Time).
+ * @QCA_WLAN_VENDOR_FEATURE_11AX: Device supports 802.11ax (HE)
+ * @QCA_WLAN_VENDOR_FEATURE_6GHZ_SUPPORT: Device supports 6 GHz band operation
+ * @QCA_WLAN_VENDOR_FEATURE_THERMAL_CONFIG: Device is capable of receiving
+ * and applying thermal configuration through
+ * %QCA_WLAN_VENDOR_ATTR_THERMAL_LEVEL and
+ * %QCA_WLAN_VENDOR_ATTR_THERMAL_COMPLETION_WINDOW attributes from
+ * userspace.
* @NUM_QCA_WLAN_VENDOR_FEATURES: Number of assigned feature bits
*/
enum qca_wlan_vendor_features {
QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON = 6,
QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY = 7,
QCA_WLAN_VENDOR_FEATURE_TWT = 8,
+ QCA_WLAN_VENDOR_FEATURE_11AX = 9,
+ QCA_WLAN_VENDOR_FEATURE_6GHZ_SUPPORT = 10,
+ QCA_WLAN_VENDOR_FEATURE_THERMAL_CONFIG = 11,
NUM_QCA_WLAN_VENDOR_FEATURES /* keep last */
};
* randomisation
* @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: 6-byte MAC address representing the
* specific BSSID to scan for.
+ * @QCA_WLAN_VENDOR_ATTR_SCAN_DWELL_TIME: Unsigned 64-bit dwell time in
+ * microseconds. This is a common value which applies across all
+ * frequencies specified by QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES.
*/
enum qca_wlan_vendor_attr_scan {
QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0,
QCA_WLAN_VENDOR_ATTR_SCAN_MAC = 9,
QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK = 10,
QCA_WLAN_VENDOR_ATTR_SCAN_BSSID = 11,
+ QCA_WLAN_VENDOR_ATTR_SCAN_DWELL_TIME = 12,
QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SCAN_MAX =
QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_GTX = 57,
+ /* Attribute to configure disconnect IEs to the driver.
+ * This carries an array of unsigned 8-bit characters.
+ *
+ * If this is configured, driver shall fill the IEs in disassoc/deauth
+ * frame.
+ * These IEs are expected to be considered only for the next
+ * immediate disconnection (disassoc/deauth frame) originated by
+ * the DUT, irrespective of the entity (user space/driver/firmware)
+ * triggering the disconnection.
+ * The host drivers are not expected to use the IEs set through
+ * this interface for further disconnections after the first immediate
+ * disconnection initiated post the configuration.
+ * If the IEs are also updated through cfg80211 interface (after the
+ * enhancement to cfg80211_disconnect), host driver is expected to
+ * take the union of IEs from both of these interfaces and send in
+ * further disassoc/deauth frames.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_DISCONNECT_IES = 58,
+
+ /* 8-bit unsigned value for ELNA bypass.
+ * 1-Enable, 0-Disable
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ELNA_BYPASS = 59,
+
+ /* 8-bit unsigned value. This attribute enables/disables the host driver
+ * to send the Beacon Report Response with failure reason for the
+ * scenarios where STA cannot honor the Beacon Report Request from AP.
+ * 1-Enable, 0-Disable.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_REPORT_FAIL = 60,
+
+ /* 8-bit unsigned value. This attribute enables/disables the host driver
+ * to send roam reason information in the Reassociation Request frame to
+ * the target AP when roaming within the same ESS.
+ * 1-Enable, 0-Disable.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ROAM_REASON = 61,
+
/* keep last */
QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_CONFIG_MAX =
QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1,
};
+/* Compatibility defines for previously used incorrect enum
+ * qca_wlan_vendor_attr_config names. These values should not be used in any
+ * new implementation. */
+#define QCA_WLAN_VENDOR_ATTR_DISCONNECT_IES \
+ QCA_WLAN_VENDOR_ATTR_CONFIG_DISCONNECT_IES
+#define QCA_WLAN_VENDOR_ATTR_BEACON_REPORT_FAIL \
+ QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_REPORT_FAIL
+
/**
* enum qca_wlan_vendor_attr_sap_config - Parameters for AP configuration
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL: Optional (u8)
+ * Channel number on which Access Point should restart.
+ * Note: If both the driver and user space application supports the 6 GHz band,
+ * this attribute is deprecated and QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_FREQUENCY
+ * should be used.
+ * To maintain backward compatibility, QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL
+ * is still used if either of the driver or user space application doesn't
+ * support the 6 GHz band.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_FREQUENCY: Optional (u32)
+ * Channel center frequency (MHz) on which the access point should restart.
*/
enum qca_wlan_vendor_attr_sap_config {
QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID = 0,
- /* 1 - reserved for QCA */
+ QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL = 1,
+
/* List of frequencies on which AP is expected to operate.
* This is irrespective of ACS configuration. This list is a priority
* based one and is looked for before the AP is created to ensure the
* the system.
*/
QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST = 2,
+ QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_FREQUENCY = 3,
QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX =
QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST - 1,
};
+/**
+ * enum qca_acs_dfs_mode - Defines different types of DFS channel
+ * configurations for ACS operation.
+ *
+ * @QCA_ACS_DFS_MODE_NONE: Refer to invalid DFS mode
+ * @QCA_ACS_DFS_MODE_ENABLE: Consider DFS channels in ACS operation
+ * @QCA_ACS_DFS_MODE_DISABLE: Do not consider DFS channels in ACS operation
+ * @QCA_ACS_DFS_MODE_DEPRIORITIZE: Deprioritize DFS channels in ACS operation
+ */
+enum qca_acs_dfs_mode {
+ QCA_ACS_DFS_MODE_NONE = 0,
+ QCA_ACS_DFS_MODE_ENABLE = 1,
+ QCA_ACS_DFS_MODE_DISABLE = 2,
+ QCA_ACS_DFS_MODE_DEPRIORITIZE = 3,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_acs_config - Defines Configuration attributes
+ * used by the vendor command QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_DFS_MODE: Required (u8)
+ * DFS mode for ACS operation from enum qca_acs_dfs_mode.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT: Required (u8)
+ * channel number hint for ACS operation, if valid channel is specified then
+ * ACS operation gives priority to this channel.
+ * Note: If both the driver and user space application supports the 6 GHz band,
+ * this attribute is deprecated and QCA_WLAN_VENDOR_ATTR_ACS_FREQUENCY_HINT
+ * should be used.
+ * To maintain backward compatibility, QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT
+ * is still used if either of the driver or user space application doesn't
+ * support the 6 GHz band.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_FREQUENCY_HINT: Required (u32).
+ * Channel center frequency (MHz) hint for ACS operation, if a valid center
+ * frequency is specified, ACS operation gives priority to this channel.
+ */
+enum qca_wlan_vendor_attr_acs_config {
+ QCA_WLAN_VENDOR_ATTR_ACS_MODE_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_ACS_DFS_MODE = 1,
+ QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT = 2,
+ QCA_WLAN_VENDOR_ATTR_ACS_FREQUENCY_HINT = 3,
+
+ QCA_WLAN_VENDOR_ATTR_ACS_DFS_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_ACS_DFS_MAX =
+ QCA_WLAN_VENDOR_ATTR_ACS_DFS_AFTER_LAST - 1,
+};
+
/**
* enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability
*/
/**
* enum qca_wlan_vendor_attr_get_wifi_info: Attributes for data used by
* QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO sub command.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION: In a request this attribute
+ * should be set to any U8 value to indicate that the driver version
+ * should be returned. When enabled in this manner, in a response this
+ * attribute will contain a string representation of the driver version.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION: In a request this attribute
+ * should be set to any U8 value to indicate that the firmware version
+ * should be returned. When enabled in this manner, in a response this
+ * attribute will contain a string representation of the firmware version.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_RADIO_INDEX: In a request this attribute
+ * should be set to any U32 value to indicate that the current radio
+ * index should be returned. When enabled in this manner, in a response
+ * this attribute will contain a U32 radio index value.
+ *
*/
enum qca_wlan_vendor_attr_get_wifi_info {
QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION = 1,
QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION = 2,
+ QCA_WLAN_VENDOR_ATTR_WIFI_INFO_RADIO_INDEX = 3,
/* keep last */
QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST - 1,
};
+/**
+ * enum qca_scan_freq_list_type: Frequency list types
+ *
+ * @QCA_PREFERRED_SCAN_FREQ_LIST: The driver shall use the scan frequency list
+ * specified with attribute QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST as
+ * a preferred frequency list for roaming.
+ *
+ * @QCA_SPECIFIC_SCAN_FREQ_LIST: The driver shall use the frequency list
+ * specified with attribute QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST as
+ * a specific frequency list for roaming.
+ */
+enum qca_scan_freq_list_type {
+ QCA_PREFERRED_SCAN_FREQ_LIST = 1,
+ QCA_SPECIFIC_SCAN_FREQ_LIST = 2,
+};
+
+/**
+ * enum qca_vendor_attr_scan_freq_list_scheme: Frequency list scheme
+ *
+ * @QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST: Nested attribute of u32 values
+ * List of frequencies in MHz to be considered for a roam scan.
+ *
+ * @QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_TYPE: Unsigned 32-bit value.
+ * Type of frequency list scheme being configured/gotten as defined by the
+ * enum qca_scan_freq_list_type.
+ */
+enum qca_vendor_attr_scan_freq_list_scheme {
+ QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST = 1,
+ QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_TYPE = 2,
+
+ /* keep last */
+ QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_SCHEME_AFTER_LAST,
+ QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_SCHEME_MAX =
+ QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_SCHEME_AFTER_LAST - 1,
+};
+
+/*
+ * enum qca_vendor_roam_triggers: Bitmap of roaming triggers
+ *
+ * @QCA_ROAM_TRIGGER_REASON_PER: Set if the roam has to be triggered based on
+ * a bad packet error rates (PER).
+ * @QCA_ROAM_TRIGGER_REASON_BEACON_MISS: Set if the roam has to be triggered
+ * based on beacon misses from the connected AP.
+ * @QCA_ROAM_TRIGGER_REASON_POOR_RSSI: Set if the roam has to be triggered
+ * due to poor RSSI of the connected AP.
+ * @QCA_ROAM_TRIGGER_REASON_BETTER_RSSI: Set if the roam has to be triggered
+ * upon finding a BSSID with a better RSSI than the connected BSSID.
+ * Here the RSSI of the current BSSID need not be poor.
+ * @QCA_ROAM_TRIGGER_REASON_PERIODIC: Set if the roam has to be triggered
+ * by triggering a periodic scan to find a better AP to roam.
+ * @QCA_ROAM_TRIGGER_REASON_DENSE: Set if the roam has to be triggered
+ * when the connected channel environment is too noisy/congested.
+ * @QCA_ROAM_TRIGGER_REASON_BTM: Set if the roam has to be triggered
+ * when BTM Request frame is received from the connected AP.
+ * @QCA_ROAM_TRIGGER_REASON_BSS_LOAD: Set if the roam has to be triggered
+ * when the channel utilization is goes above the configured threshold.
+ *
+ * Set the corresponding roam trigger reason bit to consider it for roam
+ * trigger.
+ * Userspace can set multiple bits and send to the driver. The driver shall
+ * consider all of them to trigger/initiate a roam scan.
+ */
+enum qca_vendor_roam_triggers {
+ QCA_ROAM_TRIGGER_REASON_PER = 1 << 0,
+ QCA_ROAM_TRIGGER_REASON_BEACON_MISS = 1 << 1,
+ QCA_ROAM_TRIGGER_REASON_POOR_RSSI = 1 << 2,
+ QCA_ROAM_TRIGGER_REASON_BETTER_RSSI = 1 << 3,
+ QCA_ROAM_TRIGGER_REASON_PERIODIC = 1 << 4,
+ QCA_ROAM_TRIGGER_REASON_DENSE = 1 << 5,
+ QCA_ROAM_TRIGGER_REASON_BTM = 1 << 6,
+ QCA_ROAM_TRIGGER_REASON_BSS_LOAD = 1 << 7,
+};
+
+/**
+ * enum qca_vendor_attr_roam_candidate_selection_criteria:
+ *
+ * Each attribute carries a weightage in percentage (%).
+ *
+ * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_RSSI: Unsigned 8-bit value.
+ * Represents the weightage to be given for the RSSI selection
+ * criteria among other parameters.
+ *
+ * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE: Unsigned 8-bit value.
+ * Represents the weightage to be given for the rate selection
+ * criteria among other parameters.
+ *
+ * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BW: Unsigned 8-bit value.
+ * Represents the weightage to be given for the band width selection
+ * criteria among other parameters.
+ *
+ * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BAND: Unsigned 8-bit value.
+ * Represents the weightage to be given for the band selection
+ * criteria among other parameters.
+ *
+ * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_NSS: Unsigned 8-bit value.
+ * Represents the weightage to be given for the NSS selection
+ * criteria among other parameters.
+ *
+ * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_CHAN_CONGESTION: Unsigned 8-bit value.
+ * Represents the weightage to be given for the channel congestion
+ * selection criteria among other parameters.
+ *
+ * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BEAMFORMING: Unsigned 8-bit value.
+ * Represents the weightage to be given for the beamforming selection
+ * criteria among other parameters.
+ *
+ * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_OCE_WAN: Unsigned 8-bit value.
+ * Represents the weightage to be given for the OCE selection
+ * criteria among other parameters.
+ */
+enum qca_vendor_attr_roam_candidate_selection_criteria {
+ QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_RSSI = 1,
+ QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE = 2,
+ QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BW = 3,
+ QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BAND = 4,
+ QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_NSS = 5,
+ QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_CHAN_CONGESTION = 6,
+ QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BEAMFORMING = 7,
+ QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_OCE_WAN = 8,
+
+ /* keep last */
+ QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE_AFTER_LAST,
+ QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE_MAX =
+ QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_vendor_attr_roam_control - Attributes to carry roam configuration
+ * The following attributes are used to set/get/clear the respective
+ * configurations to/from the driver.
+ * For the get, the attribute for the configuration to be queried shall
+ * carry any of its acceptable values to the driver. In return, the driver
+ * shall send the configured values within the same attribute to the user
+ * space.
+ *
+ * @QCA_ATTR_ROAM_CONTROL_ENABLE: Unsigned 8-bit value.
+ * Signifies to enable/disable roam control in driver.
+ * 1-enable, 0-disable
+ * Enable: Mandates the driver to do the further roams using the
+ * configuration parameters set through
+ * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET.
+ * Disable: Disables the driver/firmware roaming triggered through
+ * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET. Further roaming is
+ * expected to continue with the default configurations.
+ *
+ * @QCA_ATTR_ROAM_CONTROL_STATUS: Unsigned 8-bit value.
+ * This is used along with QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_GET.
+ * Roam control status is obtained through this attribute.
+ *
+ * @QCA_ATTR_ROAM_CONTROL_CLEAR_ALL: Flag attribute to indicate the
+ * complete config set through QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET
+ * is to be cleared in the driver.
+ * This is used along with QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR
+ * and shall be ignored if used with other sub commands.
+ * If this attribute is specified along with subcmd
+ * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR, the driver shall ignore
+ * all other attributes, if there are any.
+ * If this attribute is not specified when the subcmd
+ * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR is sent, the driver shall
+ * clear the data corresponding to the attributes specified.
+ *
+ * @QCA_ATTR_ROAM_CONTROL_FREQ_LIST_SCHEME: Nested attribute to carry the
+ * list of frequencies and its type, represented by
+ * enum qca_vendor_attr_scan_freq_list_scheme.
+ * Frequency list and its type are mandatory for this attribute to set
+ * the frequencies.
+ * Frequency type is mandatory for this attribute to get the frequencies
+ * and the frequency list is obtained through
+ * QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST.
+ * Frequency list type is mandatory for this attribute to clear the
+ * frequencies.
+ *
+ * @QCA_ATTR_ROAM_CONTROL_SCAN_PERIOD: Unsigned 32-bit value.
+ * Carries the value of scan period in seconds to set.
+ * The value of scan period is obtained with the same attribute for get.
+ * Clears the scan period in the driver when specified with clear command.
+ * Scan period is the idle time in seconds between each subsequent
+ * channel scans.
+ *
+ * @QCA_ATTR_ROAM_CONTROL_FULL_SCAN_PERIOD: Unsigned 32-bit value.
+ * Carries the value of full scan period in seconds to set.
+ * The value of full scan period is obtained with the same attribute for
+ * get.
+ * Clears the full scan period in the driver when specified with clear
+ * command. Full scan period is the idle period in seconds between two
+ * successive full channel roam scans.
+ *
+ * @QCA_ATTR_ROAM_CONTROL_TRIGGERS: Unsigned 32-bit value.
+ * Carries a bitmap of the roam triggers specified in
+ * enum qca_vendor_roam_triggers.
+ * The driver shall enable roaming by enabling corresponding roam triggers
+ * based on the trigger bits sent with this attribute.
+ * If this attribute is not configured, the driver shall proceed with
+ * default behavior.
+ * The bitmap configured is obtained with the same attribute for get.
+ * Clears the bitmap configured in driver when specified with clear
+ * command.
+ *
+ * @QCA_ATTR_ROAM_CONTROL_SELECTION_CRITERIA: Nested attribute signifying the
+ * weightage in percentage (%) to be given for each selection criteria.
+ * Different roam candidate selection criteria are represented by
+ * enum qca_vendor_attr_roam_candidate_selection_criteria.
+ * The driver shall select the roam candidate based on corresponding
+ * candidate selection scores sent.
+ *
+ * An empty nested attribute is used to indicate that no specific
+ * preference score/criteria is configured (i.e., to disable this mechanism
+ * in the set case and to show that the mechanism is disabled in the get
+ * case).
+ *
+ * Userspace can send multiple attributes out of this enum to the driver.
+ * Since this attribute represents the weight/percentage of preference for
+ * the respective selection criteria, it is preferred to configure 100%
+ * total weightage. The value in each attribute or cumulative weight of the
+ * values in all the nested attributes should not exceed 100%. The driver
+ * shall reject such configuration.
+ *
+ * If the weights configured through this attribute are less than 100%,
+ * the driver shall honor the weights (x%) passed for the corresponding
+ * selection criteria and choose/distribute rest of the weight (100-x)%
+ * for the other selection criteria, based on its internal logic.
+ *
+ * The selection criteria configured is obtained with the same
+ * attribute for get.
+ *
+ * Clears the selection criteria configured in the driver when specified
+ * with clear command.
+ */
+enum qca_vendor_attr_roam_control {
+ QCA_ATTR_ROAM_CONTROL_ENABLE = 1,
+ QCA_ATTR_ROAM_CONTROL_STATUS = 2,
+ QCA_ATTR_ROAM_CONTROL_CLEAR_ALL = 3,
+ QCA_ATTR_ROAM_CONTROL_FREQ_LIST_SCHEME= 4,
+ QCA_ATTR_ROAM_CONTROL_SCAN_PERIOD = 5,
+ QCA_ATTR_ROAM_CONTROL_FULL_SCAN_PERIOD = 6,
+ QCA_ATTR_ROAM_CONTROL_TRIGGERS = 7,
+ QCA_ATTR_ROAM_CONTROL_SELECTION_CRITERIA = 8,
+
+ /* keep last */
+ QCA_ATTR_ROAM_CONTROL_AFTER_LAST,
+ QCA_ATTR_ROAM_CONTROL_MAX =
+ QCA_ATTR_ROAM_CONTROL_AFTER_LAST - 1,
+};
+
+/*
+ * enum qca_wlan_vendor_attr_roaming_config_params: Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_ROAM sub command.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD: Unsigned 32-bit value.
+ * Represents the different roam sub commands referred by
+ * enum qca_wlan_vendor_roaming_subcmd.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID: Unsigned 32-bit value.
+ * Represents the Request ID for the specific set of commands.
+ * This also helps to map specific set of commands to the respective
+ * ID / client. e.g., helps to identify the user entity configuring the
+ * Blacklist BSSID and accordingly clear the respective ones with the
+ * matching ID.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS: Unsigned
+ * 32-bit value.Represents the number of whitelist SSIDs configured.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST: Nested attribute
+ * to carry the list of Whitelist SSIDs.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID: SSID (binary attribute,
+ * 0..32 octets). Represents the white list SSID. Whitelist SSIDs
+ * represent the list of SSIDs to which the firmware/driver can consider
+ * to roam to.
+ *
+ * The following PARAM_A_BAND_XX attributes are applied to 5GHz BSSIDs when
+ * comparing with a 2.4GHz BSSID. They are not applied when comparing two
+ * 5GHz BSSIDs.The following attributes are set through the Roaming SUBCMD -
+ * QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_GSCAN_ROAM_PARAMS.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD: Signed 32-bit
+ * value, RSSI threshold above which 5GHz RSSI is favored.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD: Signed 32-bit
+ * value, RSSI threshold below which 5GHz RSSI is penalized.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR: Unsigned 32-bit
+ * value, factor by which 5GHz RSSI is boosted.
+ * boost=(RSSI_measured-5GHz_boost_threshold)*5GHz_boost_factor
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR: Unsigned 32-bit
+ * value, factor by which 5GHz RSSI is penalized.
+ * penalty=(5GHz_penalty_threshold-RSSI_measured)*5GHz_penalty_factor
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST: Unsigned 32-bit
+ * value, maximum boost that can be applied to a 5GHz RSSI.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS: Unsigned 32-bit
+ * value, boost applied to current BSSID to ensure the currently
+ * associated BSSID is favored so as to prevent ping-pong situations.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER: Signed 32-bit
+ * value, RSSI below which "Alert" roam is enabled.
+ * "Alert" mode roaming - firmware is "urgently" hunting for another BSSID
+ * because the RSSI is low, or because many successive beacons have been
+ * lost or other bad link conditions.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE: Unsigned 32-bit
+ * value. 1-Enable, 0-Disable. Represents "Lazy" mode, where
+ * firmware is hunting for a better BSSID or white listed SSID even though
+ * the RSSI of the link is good. The parameters enabling the roaming are
+ * configured through the PARAM_A_BAND_XX attrbutes.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS: Nested attribute,
+ * represents the BSSIDs preferred over others while evaluating them
+ * for the roaming.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID: Unsigned
+ * 32-bit value. Represents the number of preferred BSSIDs set.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID: 6-byte MAC
+ * address representing the BSSID to be preferred.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER: Signed
+ * 32-bit value, representing the modifier to be applied to the RSSI of
+ * the BSSID for the purpose of comparing it with other roam candidate.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS: Nested attribute,
+ * represents the BSSIDs to get blacklisted for roaming.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID: Unsigned
+ * 32-bit value, represents the number of blacklisted BSSIDs.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID: 6-byte MAC
+ * address representing the Blacklisted BSSID.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_HINT: Flag attribute,
+ * indicates this BSSID blacklist as a hint to the driver. The driver can
+ * select this BSSID in the worst case (when no other BSSIDs are better).
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL: Nested attribute to
+ * set/get/clear the roam control config as
+ * defined @enum qca_vendor_attr_roam_control.
+ */
enum qca_wlan_vendor_attr_roaming_config_params {
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID = 0,
/* Flag attribute indicates this BSSID blacklist as a hint */
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_HINT = 21,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL = 22,
+
/* keep last */
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX =
};
/*
- * enum qca_wlan_vendor_attr_roam_subcmd: Attributes for data used by
- * QCA_NL80211_VENDOR_SUBCMD_ROAM sub command.
- */
-enum qca_wlan_vendor_attr_roam_subcmd {
- QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_INVALID = 0,
- QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SSID_WHITE_LIST = 1,
- QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_GSCAN_ROAM_PARAMS = 2,
- QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_LAZY_ROAM = 3,
- QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PREFS = 4,
- QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PARAMS = 5,
- QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID = 6,
-
- /* keep last */
- QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST,
- QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_MAX =
- QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST - 1,
+ * enum qca_wlan_vendor_roaming_subcmd: Referred by
+ * QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD.
+ *
+ * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SSID_WHITE_LIST: Sub command to
+ * configure the white list SSIDs. These are configured through
+ * the following attributes.
+ * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS,
+ * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST,
+ * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID
+ *
+ * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_GSCAN_ROAM_PARAMS: Sub command to
+ * configure the Roam params. These parameters are evaluated on the GScan
+ * results. Refers the attributes PARAM_A_BAND_XX above to configure the
+ * params.
+ *
+ * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_LAZY_ROAM: Sets the Lazy roam. Uses
+ * the attribute QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE
+ * to enable/disable Lazy roam.
+ *
+ * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BSSID_PREFS: Sets the BSSID
+ * preference. Contains the attribute
+ * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS to set the BSSID
+ * preference.
+ *
+ * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BLACKLIST_BSSID: Sets the Blacklist
+ * BSSIDs. Refers QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS to
+ * set the same.
+ *
+ * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET: Command to set the
+ * roam control config to the driver with the attribute
+ * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL.
+ *
+ * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_GET: Command to obtain the
+ * roam control config from driver with the attribute
+ * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL.
+ * For the get, the attribute for the configuration to be queried shall
+ * carry any of its acceptable value to the driver. In return, the driver
+ * shall send the configured values within the same attribute to the user
+ * space.
+ *
+ * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR: Command to clear the
+ * roam control config in the driver with the attribute
+ * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL.
+ * The driver shall continue with its default roaming behavior when data
+ * corresponding to an attribute is cleared.
+ */
+enum qca_wlan_vendor_roaming_subcmd {
+ QCA_WLAN_VENDOR_ROAMING_SUBCMD_INVALID = 0,
+ QCA_WLAN_VENDOR_ROAMING_SUBCMD_SSID_WHITE_LIST = 1,
+ QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_GSCAN_ROAM_PARAMS = 2,
+ QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_LAZY_ROAM = 3,
+ QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BSSID_PREFS = 4,
+ QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BSSID_PARAMS = 5,
+ QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BLACKLIST_BSSID = 6,
+ QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET = 7,
+ QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_GET = 8,
+ QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR = 9,
};
enum qca_wlan_vendor_attr_gscan_config_params {
/* Unsigned 32-bit value; a GSCAN Capabilities attribute.
* This is used to limit the maximum number of BSSIDs while sending
- * the vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM with attributes
- * QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID and
+ * the vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM with subcmd
+ * QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BLACKLIST_BSSID and attribute
* QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_MAX_NUM_BLACKLISTED_BSSID = 46,
QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS,
/* Represents the reason that LTE co-exist in the current band. */
QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX,
+ /* Represents the reason that generic, uncategorized interference has
+ * been found in the current channel.
+ */
+ QCA_WLAN_VENDOR_ACS_SELECT_REASON_GENERIC_INTERFERENCE,
+ /* Represents the reason that excessive 802.11 interference has been
+ * found in the current channel.
+ */
+ QCA_WLAN_VENDOR_ACS_SELECT_REASON_80211_INTERFERENCE,
+ /* Represents the reason that generic Continuous Wave (CW) interference
+ * has been found in the current channel.
+ */
+ QCA_WLAN_VENDOR_ACS_SELECT_REASON_CW_INTERFERENCE,
+ /* Represents the reason that Microwave Oven (MWO) interference has been
+ * found in the current channel.
+ */
+ QCA_WLAN_VENDOR_ACS_SELECT_REASON_MWO_INTERFERENCE,
+ /* Represents the reason that generic Frequency-Hopping Spread Spectrum
+ * (FHSS) interference has been found in the current channel. This may
+ * include 802.11 waveforms.
+ */
+ QCA_WLAN_VENDOR_ACS_SELECT_REASON_FHSS_INTERFERENCE,
+ /* Represents the reason that non-802.11 generic Frequency-Hopping
+ * Spread Spectrum (FHSS) interference has been found in the current
+ * channel.
+ */
+ QCA_WLAN_VENDOR_ACS_SELECT_REASON_NON_80211_FHSS_INTERFERENCE,
+ /* Represents the reason that generic Wideband (WB) interference has
+ * been found in the current channel. This may include 802.11 waveforms.
+ */
+ QCA_WLAN_VENDOR_ACS_SELECT_REASON_WB_INTERFERENCE,
+ /* Represents the reason that non-802.11 generic Wideband (WB)
+ * interference has been found in the current channel.
+ */
+ QCA_WLAN_VENDOR_ACS_SELECT_REASON_NON_80211_WB_INTERFERENCE,
+ /* Represents the reason that Jammer interference has been found in the
+ * current channel.
+ */
+ QCA_WLAN_VENDOR_ACS_SELECT_REASON_JAMMER_INTERFERENCE,
};
/**
*/
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2 = 11,
+ /*
+ * VHT segment 0 in MHz (u32) and the attribute is mandatory.
+ * Note: Event QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS includes
+ * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0
+ * along with
+ * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0.
+ *
+ * If both the driver and user-space application supports the 6 GHz
+ * band, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0
+ * is deprecated and
+ * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0
+ * should be used.
+ *
+ * To maintain backward compatibility,
+ * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0
+ * is still used if either of the driver or user space application
+ * doesn't support the 6 GHz band.
+ */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0 = 12,
+
+ /*
+ * VHT segment 1 in MHz (u32) and the attribute is mandatory.
+ * Note: Event QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS includes
+ * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1
+ * along with
+ * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1.
+ *
+ * If both the driver and user-space application supports the 6 GHz
+ * band, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1
+ * is deprecated and
+ * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1
+ * should be considered.
+ *
+ * To maintain backward compatibility,
+ * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1
+ * is still used if either of the driver or user space application
+ * doesn't support the 6 GHz band.
+ */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1 = 13,
+
/* keep last */
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST,
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX =
};
/**
- * qca_wlan_vendor_attr_external_acs_channels: Attributes to vendor subcmd
+ * enum qca_wlan_vendor_attr_external_acs_channels: Attributes to vendor subcmd
* QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This carries a list of channels
* in priority order as decided after ACS operation in userspace.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON: Required (u8).
+ * One of reason code from enum qca_wlan_vendor_acs_select_reason.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST: Required
+ * Array of nested values for each channel with following attributes:
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH
+ * Note: If both the driver and user-space application supports the 6 GHz band,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST is deprecated and use
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_LIST.
+ * To maintain backward compatibility,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST
+ * is still used if either of the driver or user space application doesn't
+ * support the 6 GHz band.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY: Required (u8).
+ * Primary channel number
+ * Note: If both the driver and user-space application supports the 6 GHz band,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY is deprecated and use
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY.
+ * To maintain backward compatibility,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY
+ * is still used if either of the driver or user space application doesn't
+ * support the 6 GHz band.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY: Required (u8).
+ * Secondary channel number, required only for 160 and 80+80 MHz bandwidths.
+ * Note: If both the driver and user-space application supports the 6 GHz band,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY is deprecated and use
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY.
+ * To maintain backward compatibility,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY
+ * is still used if either of the driver or user space application
+ * doesn't support the 6 GHz band.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0: Required (u8).
+ * VHT seg0 channel number
+ * Note: If both the driver and user-space application supports the 6 GHz band,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 is deprecated and use
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0.
+ * To maintain backward compatibility,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0
+ * is still used if either of the driver or user space application
+ * doesn't support the 6 GHz band.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1: Required (u8).
+ * VHT seg1 channel number
+ * Note: If both the driver and user-space application supports the 6 GHz band,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 is deprecated and use
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1.
+ * To maintain backward compatibility,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1
+ * is still used if either of the driver or user space application
+ * doesn't support the 6 GHz band.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH: Required (u8).
+ * Takes one of enum nl80211_chan_width values.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_LIST: Required
+ * Array of nested values for each channel with following attributes:
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY in MHz (u32),
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY in MHz (u32),
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0 in MHz (u32),
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1 in MHz (u32),
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH
+ * Note: If user-space application has no support of the 6 GHz band, this
+ * attribute is optional.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY: Required (u32)
+ * Primary channel frequency in MHz
+ * Note: If user-space application has no support of the 6 GHz band, this
+ * attribute is optional.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY: Required (u32)
+ * Secondary channel frequency in MHz used for HT 40 MHz channels.
+ * Note: If user-space application has no support of the 6 GHz band, this
+ * attribute is optional.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0: Required (u32)
+ * VHT seg0 channel frequency in MHz
+ * Note: If user-space application has no support of the 6GHz band, this
+ * attribute is optional.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1: Required (u32)
+ * VHT seg1 channel frequency in MHz
+ * Note: If user-space application has no support of the 6 GHz band, this
+ * attribute is optional.
*/
enum qca_wlan_vendor_attr_external_acs_channels {
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_INVALID = 0,
/* Channel width (u8). Takes one of enum nl80211_chan_width values. */
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH = 8,
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_LIST = 9,
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY = 10,
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY = 11,
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0 = 12,
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1 = 13,
+
/* keep last */
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST,
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_MAX =
* qca_wlan_vendor_attr_spectral_scan_request_type.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE = 23,
+ /* This specifies the frequency span over which spectral
+ * scan would be carried out. Its value depends on the
+ * value of QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE and
+ * the relation is as follows.
+ * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL
+ * Not applicable. Spectral scan would happen in the
+ * operating span.
+ * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE
+ * Center frequency (in MHz) of the span of interest or
+ * for convenience, center frequency (in MHz) of any channel
+ * in the span of interest. If agile spectral scan is initiated
+ * without setting a valid frequency it returns the error code
+ * (QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_NOT_INITIALIZED).
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FREQUENCY = 24,
+ /* Spectral scan mode. u32 attribute.
+ * It uses values defined in enum qca_wlan_vendor_spectral_scan_mode.
+ * If this attribute is not present, it is assumed to be
+ * normal mode (QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL).
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE = 25,
+ /* Spectral scan error code. u32 attribute.
+ * It uses values defined in enum
+ * qca_wlan_vendor_spectral_scan_error_code.
+ * This attribute is included only in failure scenarios.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_ERROR_CODE = 26,
+ /* 8-bit unsigned value to enable/disable debug of the
+ * Spectral DMA ring.
+ * 1-enable, 0-disable
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_RING_DEBUG = 27,
+ /* 8-bit unsigned value to enable/disable debug of the
+ * Spectral DMA buffers.
+ * 1-enable, 0-disable
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_BUFFER_DEBUG = 28,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_MAX =
* u8 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_DEFAULT_AGC_MAX_GAIN = 10,
+ /* Flag attribute to indicate agile spectral scan capability
+ * for 20/40/80 MHz modes.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL = 11,
+ /* Flag attribute to indicate agile spectral scan capability
+ * for 160 MHz mode.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL_160 = 12,
+ /* Flag attribute to indicate agile spectral scan capability
+ * for 80+80 MHz mode.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL_80_80 = 13,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_MAX =
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ENABLED = 1,
/* Flag attribute to indicate whether spectral scan is in progress*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ACTIVE = 2,
+ /* Spectral scan mode. u32 attribute.
+ * It uses values defined in enum qca_wlan_vendor_spectral_scan_mode.
+ * If this attribute is not present, normal mode
+ * (QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL is assumed to be
+ * requested.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MODE = 3,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MAX =
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG,
};
+/**
+ * qca_wlan_vendor_spectral_scan_mode: Attribute values for
+ * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE in the vendor subcmd
+ * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START and
+ * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MODE in the vendor subcmd
+ * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS. This represents the
+ * spectral scan modes.
+ * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL: Normal spectral scan:
+ * spectral scan in the current operating span.
+ * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE: Agile spectral scan:
+ * spectral scan in the configured agile span.
+ */
+enum qca_wlan_vendor_spectral_scan_mode {
+ QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL = 0,
+ QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE = 1,
+};
+
+/**
+ * qca_wlan_vendor_spectral_scan_error_code: Attribute values for
+ * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_ERROR_CODE in the vendor subcmd
+ * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START.
+ * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_UNSUPPORTED: Changing the value
+ * of a parameter is not supported.
+ * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_MODE_UNSUPPORTED: Requested spectral scan
+ * mode is not supported.
+ * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_INVALID_VALUE: A parameter
+ * has invalid value.
+ * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_NOT_INITIALIZED: A parameter
+ * is not initialized.
+ */
+enum qca_wlan_vendor_spectral_scan_error_code {
+ QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_UNSUPPORTED = 0,
+ QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_MODE_UNSUPPORTED = 1,
+ QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_INVALID_VALUE = 2,
+ QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_NOT_INITIALIZED = 3,
+};
+
/**
* qca_wlan_vendor_spectral_scan_cap_hw_gen: Attribute values for
* QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN to the vendor subcmd
QCA_WLAN_HANG_DXE_FAILURE = 12,
/* WMI pending commands exceed the maximum count */
QCA_WLAN_HANG_WMI_EXCEED_MAX_PENDING_CMDS = 13,
+ /* Timeout for peer STA connection accept command's response from the
+ * FW in AP mode. This command is triggered when a STA (peer) connects
+ * to AP (DUT).
+ */
+ QCA_WLAN_HANG_AP_STA_CONNECT_REQ_TIMEOUT = 14,
+ /* Timeout for the AP connection accept command's response from the FW
+ * in STA mode. This command is triggered when the STA (DUT) connects
+ * to an AP (peer).
+ */
+ QCA_WLAN_HANG_STA_AP_CONNECT_REQ_TIMEOUT = 15,
+ /* Timeout waiting for the response to the MAC HW mode change command
+ * sent to FW as a part of MAC mode switch among DBS (Dual Band
+ * Simultaneous), SCC (Single Channel Concurrency), and MCC (Multi
+ * Channel Concurrency) mode.
+ */
+ QCA_WLAN_HANG_MAC_HW_MODE_CHANGE_TIMEOUT = 16,
+ /* Timeout waiting for the response from FW to configure the MAC HW's
+ * mode. This operation is to configure the single/two MACs in either
+ * SCC/MCC/DBS mode.
+ */
+ QCA_WLAN_HANG_MAC_HW_MODE_CONFIG_TIMEOUT = 17,
+ /* Timeout waiting for response of VDEV start command from the FW */
+ QCA_WLAN_HANG_VDEV_START_RESPONSE_TIMED_OUT = 18,
+ /* Timeout waiting for response of VDEV restart command from the FW */
+ QCA_WLAN_HANG_VDEV_RESTART_RESPONSE_TIMED_OUT = 19,
+ /* Timeout waiting for response of VDEV stop command from the FW */
+ QCA_WLAN_HANG_VDEV_STOP_RESPONSE_TIMED_OUT = 20,
+ /* Timeout waiting for response of VDEV delete command from the FW */
+ QCA_WLAN_HANG_VDEV_DELETE_RESPONSE_TIMED_OUT = 21,
+ /* Timeout waiting for response of peer all delete request command to
+ * the FW on a specific VDEV.
+ */
+ QCA_WLAN_HANG_VDEV_PEER_DELETE_ALL_RESPONSE_TIMED_OUT = 22,
};
/**
* qca_wlan_vendor_hang_reason.
*/
QCA_WLAN_VENDOR_ATTR_HANG_REASON = 1,
+ /* The binary blob data associated with the hang reason specified by
+ * QCA_WLAN_VENDOR_ATTR_HANG_REASON. This binary data is expected to
+ * contain the required dump to analyze the reason for the hang.
+ * NLA_BINARY attribute, the max size is 1024 bytes.
+ */
+ QCA_WLAN_VENDOR_ATTR_HANG_REASON_DATA = 2,
QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_HANG_MAX =
enum qca_wlan_vendor_attr_rtplinst {
QCA_WLAN_VENDOR_ATTR_RTPLINST_INVALID = 0,
- /* Primary channel number (u8) */
+ /* Primary channel number (u8).
+ * Note: If both the driver and user space application support the
+ * 6 GHz band, this attribute is deprecated and
+ * QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY_FREQUENCY should be used. To
+ * maintain backward compatibility,
+ * QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY is still used if either the
+ * driver or user space application or both do not support the 6 GHz
+ * band.
+ */
QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY = 1,
/* Representative Tx power in dBm (s32) with emphasis on throughput. */
QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_THROUGHPUT = 2,
/* Representative Tx power in dBm (s32) with emphasis on range. */
QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_RANGE = 3,
+ /* Primary channel center frequency (u32) in MHz */
+ QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY_FREQUENCY = 4,
QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_RTPLINST_MAX =
QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST - 1,
};
+/**
+ * enum qca_wlan_vendor_thermal_level - Defines various thermal levels
+ * configured by userspace to the driver/firmware. The values will be
+ * encapsulated in QCA_WLAN_VENDOR_ATTR_THERMAL_LEVEL attribute.
+ * The driver/firmware takes actions requested by userspace such as throttling
+ * wifi TX etc. in order to mitigate high temperature.
+ *
+ * @QCA_WLAN_VENDOR_THERMAL_LEVEL_NONE: Stop/clear all throttling actions.
+ * @QCA_WLAN_VENDOR_THERMAL_LEVEL_LIGHT: Throttle TX lightly.
+ * @QCA_WLAN_VENDOR_THERMAL_LEVEL_MODERATE: Throttle TX moderately.
+ * @QCA_WLAN_VENDOR_THERMAL_LEVEL_SEVERE: Throttle TX severely.
+ * @QCA_WLAN_VENDOR_THERMAL_LEVEL_CRITICAL: Critical thermal level reached.
+ * @QCA_WLAN_VENDOR_THERMAL_LEVEL_EMERGENCY: Emergency thermal level reached.
+ */
+enum qca_wlan_vendor_thermal_level {
+ QCA_WLAN_VENDOR_THERMAL_LEVEL_NONE = 0,
+ QCA_WLAN_VENDOR_THERMAL_LEVEL_LIGHT = 1,
+ QCA_WLAN_VENDOR_THERMAL_LEVEL_MODERATE = 2,
+ QCA_WLAN_VENDOR_THERMAL_LEVEL_SEVERE = 3,
+ QCA_WLAN_VENDOR_THERMAL_LEVEL_CRITICAL = 4,
+ QCA_WLAN_VENDOR_THERMAL_LEVEL_EMERGENCY = 5,
+};
+
/**
* enum qca_wlan_vendor_attr_thermal_cmd - Vendor subcmd attributes to set
* cmd value. Used for NL attributes for data used by
* u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE = 1,
+ /* Userspace uses this attribute to configure thermal level to the
+ * driver/firmware. Used in request, u32 attribute, possible values
+ * are defined in enum qca_wlan_vendor_thermal_level.
+ */
+ QCA_WLAN_VENDOR_ATTR_THERMAL_LEVEL = 2,
+ /* Userspace uses this attribute to configure the time in which the
+ * driver/firmware should complete applying settings it received from
+ * userspace with QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SET_LEVEL
+ * command type. Used in request, u32 attribute, value is in
+ * milliseconds. A value of zero indicates to apply the settings
+ * immediately. The driver/firmware can delay applying the configured
+ * thermal settings within the time specified in this attribute if
+ * there is any critical ongoing operation.
+ */
+ QCA_WLAN_VENDOR_ATTR_THERMAL_COMPLETION_WINDOW = 3,
/* keep last */
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST,
* suspend action.
* @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME: Request to execute thermal
* resume action.
+ * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SET_LEVEL: Configure thermal level to
+ * the driver/firmware.
*/
enum qca_wlan_vendor_attr_thermal_cmd_type {
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS,
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE,
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND,
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME,
+ QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SET_LEVEL,
};
/**
QCA_MPTA_HELPER_VENDOR_ATTR_AFTER_LAST - 1
};
+/**
+ * enum qca_wlan_vendor_beacon_reporting_op_types - Defines different types of
+ * operations for which %QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING can be used.
+ * Will be used by %QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE.
+ *
+ * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START: Sent by userspace to the driver
+ * to request the driver to start reporting Beacon frames.
+ * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_STOP: Sent by userspace to the driver to
+ * request the driver to stop reporting Beacon frames.
+ * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO: Sent by the driver to
+ * userspace to report received Beacon frames.
+ * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE: Sent by the driver to userspace
+ * to indicate that the driver is going to pause reporting Beacon frames.
+ */
+enum qca_wlan_vendor_beacon_reporting_op_types {
+ QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START = 0,
+ QCA_WLAN_VENDOR_BEACON_REPORTING_OP_STOP = 1,
+ QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO = 2,
+ QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE = 3,
+};
+
+/**
+ * enum qca_wlan_vendor_beacon_reporting_pause_reasons - Defines different types
+ * of reasons for which the driver is pausing reporting Beacon frames. Will be
+ * used by %QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PAUSE_REASON.
+ *
+ * @QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_UNSPECIFIED: For unspecified
+ * reasons.
+ * @QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_SCAN_STARTED: When the
+ * driver/firmware is starting a scan.
+ * @QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_DISCONNECTED: When the
+ * driver/firmware disconnects from the ESS and indicates the disconnection to
+ * userspace (non-seamless roaming case). This reason code will be used by the
+ * driver/firmware to indicate stopping of beacon report events. Userspace will
+ * need to start beacon reporting again (if desired) by sending vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING with
+ * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE set to
+ * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START after the next connection is
+ * completed.
+ */
+enum qca_wlan_vendor_beacon_reporting_pause_reasons {
+ QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_UNSPECIFIED = 0,
+ QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_SCAN_STARTED = 1,
+ QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_DISCONNECTED = 2,
+};
+
+/*
+ * enum qca_wlan_vendor_attr_beacon_reporting_params - List of attributes used
+ * in vendor sub-command QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING.
+ */
+enum qca_wlan_vendor_attr_beacon_reporting_params {
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_INVALID = 0,
+ /* Specifies the type of operation that the vendor command/event is
+ * intended for. Possible values for this attribute are defined in
+ * enum qca_wlan_vendor_beacon_reporting_op_types. u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE = 1,
+ /* Optionally set by userspace to request the driver to report Beacon
+ * frames using asynchronous vendor events when the
+ * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to
+ * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START. NLA_FLAG attribute.
+ * If this flag is not set, the driver will only update Beacon frames in
+ * cfg80211 scan cache but not send any vendor events.
+ */
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_ACTIVE_REPORTING = 2,
+ /* Optionally used by userspace to request the driver/firmware to report
+ * Beacon frames periodically when the
+ * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to
+ * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START.
+ * u32 attribute, indicates the period of Beacon frames to be reported
+ * and in the units of beacon interval.
+ * If this attribute is missing in the command, then the default value
+ * of 1 will be assumed by driver, i.e., to report every Beacon frame.
+ * Zero is an invalid value.
+ * If a valid value is received for this attribute, the driver will
+ * update the cfg80211 scan cache periodically as per the value received
+ * in this attribute in addition to updating the cfg80211 scan cache
+ * when there is significant change in Beacon frame IEs.
+ */
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PERIOD = 3,
+ /* Used by the driver to encapsulate the SSID when the
+ * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to
+ * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO.
+ * u8 array with a maximum size of 32.
+ *
+ * When generating beacon report from non-MBSSID Beacon frame, the SSID
+ * will be taken from the SSID element of the received Beacon frame.
+ *
+ * When generating beacon report from Multiple BSSID Beacon frame and if
+ * the BSSID of the current connected BSS matches the BSSID of the
+ * transmitting BSS, the SSID will be taken from the SSID element of the
+ * received Beacon frame.
+ *
+ * When generating beacon report from Multiple BSSID Beacon frame and if
+ * the BSSID of the current connected BSS matches the BSSID of one of
+ * the* nontransmitting BSSs, the SSID will be taken from the SSID field
+ * included in the nontransmitted BSS profile whose derived BSSID is
+ * same as the BSSID of the current connected BSS. When there is no
+ * nontransmitted BSS profile whose derived BSSID is same as the BSSID
+ * of current connected* BSS, this attribute will not be present.
+ */
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_SSID = 4,
+ /* Used by the driver to encapsulate the BSSID of the AP to which STA is
+ * currently connected to when the
+ * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to
+ * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. u8 array with a
+ * fixed size of 6 bytes.
+ *
+ * When generating beacon report from a Multiple BSSID beacon and the
+ * current connected BSSID matches one of the nontransmitted BSSIDs in a
+ * Multiple BSSID set, this BSSID will be that particular nontransmitted
+ * BSSID and not the transmitted BSSID (i.e., the transmitting address
+ * of the Beacon frame).
+ */
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_BSSID = 5,
+ /* Used by the driver to encapsulate the frequency in MHz on which
+ * the Beacon frame was received when the
+ * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is
+ * set to QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_FREQ = 6,
+ /* Used by the driver to encapsulate the Beacon interval
+ * when the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to
+ * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO.
+ * u16 attribute. The value will be copied from the Beacon frame and the
+ * units are TUs.
+ */
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_BI = 7,
+ /* Used by the driver to encapsulate the Timestamp field from the Beacon
+ * frame when the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set
+ * to QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO.
+ * u64 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_TSF = 8,
+ /* Used by the driver to encapsulate the CLOCK_BOOTTIME when this
+ * Beacon frame is received in the driver when the
+ * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to
+ * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. u64 attribute, in
+ * the units of nanoseconds. This value is expected to have accuracy of
+ * about 10 ms.
+ */
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_BOOTTIME_WHEN_RECEIVED = 9,
+ /* Used by the driver to encapsulate the IEs of the Beacon frame from
+ * which this event is generated when the
+ * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to
+ * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. u8 array.
+ */
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_IES = 10,
+ /* Used by the driver to specify the reason for the driver/firmware to
+ * pause sending beacons to userspace when the
+ * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to
+ * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE. Possible values are
+ * defined in enum qca_wlan_vendor_beacon_reporting_pause_reasons, u32
+ * attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PAUSE_REASON = 11,
+ /* Used by the driver to specify whether the driver will automatically
+ * resume reporting beacon events to userspace later (for example after
+ * the ongoing off-channel activity is completed etc.) when the
+ * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to
+ * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE. NLA_FLAG attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES = 12,
+ /* Optionally set by userspace to request the driver not to resume
+ * beacon reporting after a pause is completed, when the
+ * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to
+ * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START. NLA_FLAG attribute.
+ * If this flag is set, the driver will not resume beacon reporting
+ * after any pause in beacon reporting is completed. Userspace has to
+ * send QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START command again in order
+ * to initiate beacon reporting again. If this flag is set in the recent
+ * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START command, then in the
+ * subsequent QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE event (if any)
+ * the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES shall not be
+ * set by the driver. Setting this flag until and unless there is a
+ * specific need is not recommended as there is a chance of some beacons
+ * received after pause command and next start command being not
+ * reported.
+ */
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_DO_NOT_RESUME = 13,
+
+ /* Keep last */
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_LAST,
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_MAX =
+ QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_LAST - 1
+};
+
+/**
+ * enum qca_vendor_interop_issues_ap_type - Interop issue types
+ * This enum defines the valid set of values of interop issue types. These
+ * values are used by attribute %QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_TYPE.
+ *
+ * @QCA_VENDOR_INTEROP_ISSUES_AP_ON_STA_PS: The AP has power save interop issue
+ * when the STA's Qpower feature is enabled.
+ */
+enum qca_vendor_interop_issues_ap_type {
+ QCA_VENDOR_INTEROP_ISSUES_AP_INVALID = 0,
+ QCA_VENDOR_INTEROP_ISSUES_AP_ON_STA_PS = 1,
+};
+
+/**
+ * enum qca_vendor_attr_interop_issues_ap - attribute for AP with interop issues
+ * Values are used by %QCA_NL80211_VENDOR_SUBCMD_INTEROP_ISSUES_AP.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_INVALID: Invalid value
+ * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_TYPE: Interop issue type
+ * 32-bit unsigned value. The values defined in enum
+ * qca_vendor_interop_issues_ap_type are used.
+ * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_LIST: APs' BSSID container
+ * array of nested QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_BSSID attributes.
+ * It is present and mandatory for the command but is not used for the event
+ * since only a single BSSID is reported in an event.
+ * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_BSSID: AP's BSSID 6-byte MAC address.
+ * It is used within the nested QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_LIST
+ * attribute in command case and without such encapsulation in the event case.
+ * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_AFTER_LAST: last value
+ * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_MAX: max value
+ */
+enum qca_vendor_attr_interop_issues_ap {
+ QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_INVALID,
+ QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_TYPE,
+ QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_LIST,
+ QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_BSSID,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_MAX =
+ QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_AFTER_LAST - 1
+};
+
+/**
+ * enum qca_vendor_oem_device_type - Represents the target device in firmware.
+ * It is used by QCA_WLAN_VENDOR_ATTR_OEM_DEVICE_INFO.
+ *
+ * @QCA_VENDOR_OEM_DEVICE_VIRTUAL: The command is intended for
+ * a virtual device.
+ *
+ * @QCA_VENDOR_OEM_DEVICE_PHYSICAL: The command is intended for
+ * a physical device.
+ */
+enum qca_vendor_oem_device_type {
+ QCA_VENDOR_OEM_DEVICE_VIRTUAL = 0,
+ QCA_VENDOR_OEM_DEVICE_PHYSICAL = 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_oem_data_params - Used by the vendor command/event
+ * QCA_NL80211_VENDOR_SUBCMD_OEM_DATA.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_OEM_DATA_CMD_DATA: The binary blob for the vendor
+ * command/event QCA_NL80211_VENDOR_SUBCMD_OEM_DATA are carried through this
+ * attribute.
+ * NLA_BINARY attribute, the max size is 1024 bytes.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_OEM_DEVICE_INFO: The binary blob will be routed
+ * based on this field. This optional attribute is included to specify whether
+ * the device type is a virtual device or a physical device for the
+ * command/event. This attribute can be omitted for a virtual device (default)
+ * command/event.
+ * This u8 attribute is used to carry information for the device type using
+ * values defined by enum qca_vendor_oem_device_type.
+ */
+enum qca_wlan_vendor_attr_oem_data_params {
+ QCA_WLAN_VENDOR_ATTR_OEM_DATA_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_OEM_DATA_CMD_DATA = 1,
+ QCA_WLAN_VENDOR_ATTR_OEM_DEVICE_INFO = 2,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_OEM_DATA_PARAMS_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_OEM_DATA_PARAMS_MAX =
+ QCA_WLAN_VENDOR_ATTR_OEM_DATA_PARAMS_AFTER_LAST - 1
+};
+
+/**
+ * enum qca_wlan_vendor_attr_avoid_frequency_ext - Defines attributes to be
+ * used with vendor command/event QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_RANGE: Required
+ * Nested attribute containing multiple ranges with following attributes:
+ * QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_START and
+ * QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_END.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_START: Required (u32)
+ * Starting center frequency in MHz.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_END: Required (u32)
+ * Ending center frequency in MHz.
+ */
+enum qca_wlan_vendor_attr_avoid_frequency_ext {
+ QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_RANGE = 1,
+ QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_START = 2,
+ QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_END = 3,
+
+ QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_MAX =
+ QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_AFTER_LAST - 1
+};
+
+/*
+ * enum qca_wlan_vendor_attr_add_sta_node_params - Used by the vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE.
+ */
+enum qca_wlan_vendor_attr_add_sta_node_params {
+ QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_INVALID = 0,
+ /* 6 byte MAC address of STA */
+ QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_MAC_ADDR = 1,
+ /* Authentication algorithm used by the station of size u16;
+ * defined in enum nl80211_auth_type.
+ */
+ QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_AUTH_ALGO = 2,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_PARAM_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_PARAM_MAX =
+ QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_PARAM_AFTER_LAST - 1
+};
+
+/**
+ * enum qca_btc_chain_mode - Specifies BT coex chain mode.
+ * This enum defines the valid set of values of BT coex chain mode.
+ * These values are used by attribute %QCA_VENDOR_ATTR_BTC_CHAIN_MODE of
+ * %QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE.
+ *
+ * @QCA_BTC_CHAIN_SHARED: chains of BT and WLAN 2.4G are shared.
+ * @QCA_BTC_CHAIN_SEPARATED: chains of BT and WLAN 2.4G are separated.
+ */
+enum qca_btc_chain_mode {
+ QCA_BTC_CHAIN_SHARED = 0,
+ QCA_BTC_CHAIN_SEPARATED = 1,
+};
+
+/**
+ * enum qca_vendor_attr_btc_chain_mode - Specifies attributes for BT coex
+ * chain mode.
+ * Attributes for data used by QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE.
+ *
+ * @QCA_VENDOR_ATTR_COEX_BTC_CHAIN_MODE: u32 attribute.
+ * Indicates the BT coex chain mode, are 32-bit values from
+ * enum qca_btc_chain_mode. This attribute is mandatory.
+ *
+ * @QCA_VENDOR_ATTR_COEX_BTC_CHAIN_MODE_RESTART: flag attribute.
+ * If set, vdev should be restarted when BT coex chain mode is updated.
+ * This attribute is optional.
+ */
+enum qca_vendor_attr_btc_chain_mode {
+ QCA_VENDOR_ATTR_BTC_CHAIN_MODE_INVALID = 0,
+ QCA_VENDOR_ATTR_BTC_CHAIN_MODE = 1,
+ QCA_VENDOR_ATTR_BTC_CHAIN_MODE_RESTART = 2,
+
+ /* Keep last */
+ QCA_VENDOR_ATTR_BTC_CHAIN_MODE_LAST,
+ QCA_VENDOR_ATTR_BTC_CHAIN_MODE_MAX =
+ QCA_VENDOR_ATTR_BTC_CHAIN_MODE_LAST - 1,
+};
+
+/**
+ * enum qca_vendor_wlan_sta_flags - Station feature flags
+ * Bits will be set to 1 if the corresponding features are enabled.
+ * @QCA_VENDOR_WLAN_STA_FLAG_AMPDU: AMPDU is enabled for the station
+ * @QCA_VENDOR_WLAN_STA_FLAG_TX_STBC: TX Space-time block coding is enabled
+ for the station
+ * @QCA_VENDOR_WLAN_STA_FLAG_RX_STBC: RX Space-time block coding is enabled
+ for the station
+ */
+enum qca_vendor_wlan_sta_flags {
+ QCA_VENDOR_WLAN_STA_FLAG_AMPDU = BIT(0),
+ QCA_VENDOR_WLAN_STA_FLAG_TX_STBC = BIT(1),
+ QCA_VENDOR_WLAN_STA_FLAG_RX_STBC = BIT(2),
+};
+
+/**
+ * enum qca_vendor_wlan_sta_guard_interval - Station guard interval
+ * @QCA_VENDOR_WLAN_STA_GI_800_NS: Legacy normal guard interval
+ * @QCA_VENDOR_WLAN_STA_GI_400_NS: Legacy short guard interval
+ * @QCA_VENDOR_WLAN_STA_GI_1600_NS: Guard interval used by HE
+ * @QCA_VENDOR_WLAN_STA_GI_3200_NS: Guard interval used by HE
+ */
+enum qca_vendor_wlan_sta_guard_interval {
+ QCA_VENDOR_WLAN_STA_GI_800_NS = 0,
+ QCA_VENDOR_WLAN_STA_GI_400_NS = 1,
+ QCA_VENDOR_WLAN_STA_GI_1600_NS = 2,
+ QCA_VENDOR_WLAN_STA_GI_3200_NS = 3,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_get_sta_info - Defines attributes
+ * used by QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO vendor command.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAC:
+ * Required attribute in request for AP mode only, 6-byte MAC address,
+ * corresponding to the station's MAC address for which information is
+ * requested. For STA mode this is not required as the info always correspond
+ * to the self STA and the current/last association.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_FLAGS:
+ * Optionally used in response, u32 attribute, contains a bitmap of different
+ * fields defined in enum qca_vendor_wlan_sta_flags, used in AP mode only.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_GUARD_INTERVAL:
+ * Optionally used in response, u32 attribute, possible values are defined in
+ * enum qca_vendor_wlan_sta_guard_interval, used in AP mode only.
+ * Guard interval used by the station.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_RETRY_COUNT:
+ * Optionally used in response, u32 attribute, used in AP mode only.
+ * Value indicates the number of data frames received from station with retry
+ * bit set to 1 in FC.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BC_MC_COUNT:
+ * Optionally used in response, u32 attribute, used in AP mode only.
+ * Counter for number of data frames with broadcast or multicast address in
+ * the destination address received from the station.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_SUCCEED:
+ * Optionally used in response, u32 attribute, used in both STA and AP modes.
+ * Value indicates the number of data frames successfully transmitted only
+ * after retrying the packets and for which the TX status has been updated
+ * back to host from target.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_EXHAUSTED:
+ * Optionally used in response, u32 attribute, used in both STA and AP mode.
+ * Value indicates the number of data frames not transmitted successfully even
+ * after retrying the packets for the number of times equal to the total number
+ * of retries allowed for that packet and for which the TX status has been
+ * updated back to host from target.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_TOTAL:
+ * Optionally used in response, u32 attribute, used in AP mode only.
+ * Counter in the target for the number of data frames successfully transmitted
+ * to the station.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY:
+ * Optionally used in response, u32 attribute, used in AP mode only.
+ * Value indicates the number of data frames successfully transmitted only
+ * after retrying the packets.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY_EXHAUSTED:
+ * Optionally used in response, u32 attribute, used in both STA & AP mode.
+ * Value indicates the number of data frames not transmitted successfully even
+ * after retrying the packets for the number of times equal to the total number
+ * of retries allowed for that packet.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_PROBE_REQ_BMISS_COUNT: u32, used in
+ * the STA mode only. Represent the number of probe requests sent by the STA
+ * while attempting to roam on missing certain number of beacons from the
+ * connected AP. If queried in the disconnected state, this represents the
+ * count for the last connected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_PROBE_RESP_BMISS_COUNT: u32, used in
+ * the STA mode. Represent the number of probe responses received by the station
+ * while attempting to roam on missing certain number of beacons from the
+ * connected AP. When queried in the disconnected state, this represents the
+ * count when in last connected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_ALL_COUNT: u32, used in the
+ * STA mode only. Represents the total number of frames sent out by STA
+ * including Data, ACK, RTS, CTS, Control Management. This data is maintained
+ * only for the connect session. Represents the count of last connected session,
+ * when queried in the disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_COUNT: u32, used in the STA mode.
+ * Total number of RTS sent out by the STA. This data is maintained per connect
+ * session. Represents the count of last connected session, when queried in the
+ * disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_RETRY_FAIL_COUNT: u32, used in the
+ * STA mode.Represent the number of RTS transmission failure that reach retry
+ * limit. This data is maintained per connect session. Represents the count of
+ * last connected session, when queried in the disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_NON_AGGREGATED_COUNT: u32, used in
+ * the STA mode. Represent the total number of non aggregated frames transmitted
+ * by the STA. This data is maintained per connect session. Represents the count
+ * of last connected session, when queried in the disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_AGGREGATED_COUNT: u32, used in the
+ * STA mode. Represent the total number of aggregated frames transmitted by the
+ * STA. This data is maintained per connect session. Represents the count of
+ * last connected session, when queried in the disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_GOOD_PLCP_COUNT: u32, used in
+ * the STA mode. Represents the number of received frames with a good PLCP. This
+ * data is maintained per connect session. Represents the count of last
+ * connected session, when queried in the disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_INVALID_DELIMITER_COUNT: u32,
+ * used in the STA mode. Represents the number of occasions that no valid
+ * delimiter is detected by A-MPDU parser. This data is maintained per connect
+ * session. Represents the count of last connected session, when queried in the
+ * disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_CRC_FAIL_COUNT: u32, used in the
+ * STA mode. Represents the number of frames for which CRC check failed in the
+ * MAC. This data is maintained per connect session. Represents the count of
+ * last connected session, when queried in the disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_ACKS_GOOD_FCS_COUNT: u32, used in the
+ * STA mode. Represents the number of unicast ACKs received with good FCS. This
+ * data is maintained per connect session. Represents the count of last
+ * connected session, when queried in the disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BLOCKACK_COUNT: u32, used in the STA
+ * mode. Represents the number of received Block Acks. This data is maintained
+ * per connect session. Represents the count of last connected session, when
+ * queried in the disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BEACON_COUNT: u32, used in the STA
+ * mode. Represents the number of beacons received from the connected BSS. This
+ * data is maintained per connect session. Represents the count of last
+ * connected session, when queried in the disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_OTHER_BEACON_COUNT: u32, used in the
+ * STA mode. Represents the number of beacons received by the other BSS when in
+ * connected state (through the probes done by the STA). This data is maintained
+ * per connect session. Represents the count of last connected session, when
+ * queried in the disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_UCAST_DATA_GOOD_FCS_COUNT: u64, used in
+ * the STA mode. Represents the number of received DATA frames with good FCS and
+ * matching Receiver Address when in connected state. This data is maintained
+ * per connect session. Represents the count of last connected session, when
+ * queried in the disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_DATA_BC_MC_DROP_COUNT: u32, used in the
+ * STA mode. Represents the number of RX Data multicast frames dropped by the HW
+ * when in the connected state. This data is maintained per connect session.
+ * Represents the count of last connected session, when queried in the
+ * disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_1MBPS: u32, used in the
+ * STA mode. This represents the target power in dBm for the transmissions done
+ * to the AP in 2.4 GHz at 1 Mbps (DSSS) rate. This data is maintained per
+ * connect session. Represents the count of last connected session, when
+ * queried in the disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_6MBPS: u32, used in the
+ * STA mode. This represents the Target power in dBm for transmissions done to
+ * the AP in 2.4 GHz at 6 Mbps (OFDM) rate. This data is maintained per connect
+ * session. Represents the count of last connected session, when queried in the
+ * disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_MCS0: u32, used in the
+ * STA mode. This represents the Target power in dBm for transmissions done to
+ * the AP in 2.4 GHz at MCS0 rate. This data is maintained per connect session.
+ * Represents the count of last connected session, when queried in the
+ * disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_6MBPS: u32, used in the
+ * STA mode. This represents the Target power in dBm for transmissions done to
+ * the AP in 5 GHz at 6 Mbps (OFDM) rate. This data is maintained per connect
+ * session. Represents the count of last connected session, when queried in
+ * the disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_MCS0: u32, used in the
+ * STA mode. This represents the Target power in dBm for for transmissions done
+ * to the AP in 5 GHz at MCS0 rate. This data is maintained per connect session.
+ * Represents the count of last connected session, when queried in the
+ * disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_HW_BUFFERS_OVERFLOW_COUNT: u32, used
+ * in the STA mode. This represents the Nested attribute representing the
+ * overflow counts of each receive buffer allocated to the hardware during the
+ * STA's connection. The number of hw buffers might vary for each WLAN
+ * solution and hence this attribute represents the nested array of all such
+ * HW buffer count. This data is maintained per connect session. Represents
+ * the count of last connected session, when queried in the disconnected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAX_TX_POWER: u32, Max TX power (dBm)
+ * allowed as per the regulatory requirements for the current or last connected
+ * session. Used in the STA mode.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_TX_POWER: u32, Latest TX power
+ * (dBm) used by the station in its latest unicast frame while communicating
+ * to the AP in the connected state. When queried in the disconnected state,
+ * this represents the TX power used by the STA with last AP communication
+ * when in connected state.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ANI_LEVEL: u32, Adaptive noise immunity
+ * level used to adjust the RX sensitivity. Represents the current ANI level
+ * when queried in the connected state. When queried in the disconnected
+ * state, this corresponds to the latest ANI level at the instance of
+ * disconnection.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_IES: Binary attribute containing
+ * the raw information elements from Beacon frames. Represents the Beacon frames
+ * of the current BSS in the connected state. When queried in the disconnected
+ * state, these IEs correspond to the last connected BSSID.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PROBE_RESP_IES: Binary attribute
+ * containing the raw information elements from Probe Response frames.
+ * Represents the Probe Response frames of the current BSS in the connected
+ * state. When queried in the disconnected state, these IEs correspond to the
+ * last connected BSSID.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_DRIVER_DISCONNECT_REASON: u32, Driver
+ * disconnect reason for the last disconnection if the disconnection is
+ * triggered from the host driver. The values are referred from
+ * enum qca_disconnect_reason_codes.
+ */
+enum qca_wlan_vendor_attr_get_sta_info {
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAC = 1,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_FLAGS = 2,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_GUARD_INTERVAL = 3,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_RETRY_COUNT = 4,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BC_MC_COUNT = 5,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_SUCCEED = 6,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_EXHAUSTED = 7,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_TOTAL = 8,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY = 9,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY_EXHAUSTED = 10,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_PROBE_REQ_BMISS_COUNT = 11,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_PROBE_RESP_BMISS_COUNT = 12,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_ALL_COUNT = 13,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_COUNT = 14,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_RETRY_FAIL_COUNT = 15,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_NON_AGGREGATED_COUNT = 16,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_AGGREGATED_COUNT = 17,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_GOOD_PLCP_COUNT = 18,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_INVALID_DELIMITER_COUNT = 19,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_CRC_FAIL_COUNT = 20,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_ACKS_GOOD_FCS_COUNT = 21,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BLOCKACK_COUNT = 22,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BEACON_COUNT = 23,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_OTHER_BEACON_COUNT = 24,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_UCAST_DATA_GOOD_FCS_COUNT = 25,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_DATA_BC_MC_DROP_COUNT = 26,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_1MBPS = 27,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_6MBPS = 28,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_MCS0 = 29,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_6MBPS = 30,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_MCS0 = 31,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_HW_BUFFERS_OVERFLOW_COUNT = 32,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAX_TX_POWER = 33,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_TX_POWER = 34,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ANI_LEVEL = 35,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_IES = 36,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PROBE_RESP_IES = 37,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_DRIVER_DISCONNECT_REASON = 38,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAX =
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_update_sta_info - Defines attributes
+ * used by QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO vendor command.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_CONNECT_CHANNELS: Type is NLA_UNSPEC.
+ * Used in STA mode. This attribute represents the list of channel center
+ * frequencies in MHz (u32) the station has learnt during the last connection
+ * or roaming attempt. This information shall not signify the channels for
+ * an explicit scan request from the user space. Host drivers can update this
+ * information to the user space in both connected and disconnected state.
+ * In the disconnected state this information shall signify the channels
+ * scanned in the last connection/roam attempt that lead to the disconnection.
+ */
+enum qca_wlan_vendor_attr_update_sta_info {
+ QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_CONNECT_CHANNELS = 1,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_MAX =
+ QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_disconnect_reason_codes - Specifies driver disconnect reason codes.
+ * Used when the driver triggers the STA to disconnect from the AP.
+ *
+ * @QCA_DISCONNECT_REASON_UNSPECIFIED: The host driver triggered the
+ * disconnection with the AP due to unspecified reasons.
+ *
+ * @QCA_DISCONNECT_REASON_INTERNAL_ROAM_FAILURE: The host driver triggered the
+ * disconnection with the AP due to a roaming failure. This roaming is triggered
+ * internally (host driver/firmware).
+ *
+ * @QCA_DISCONNECT_REASON_EXTERNAL_ROAM_FAILURE: The driver disconnected from
+ * the AP when the user/external triggered roaming fails.
+ *
+ * @QCA_DISCONNECT_REASON_GATEWAY_REACHABILITY_FAILURE: This reason code is used
+ * by the host driver whenever gateway reachability failure is detected and the
+ * driver disconnects with AP.
+ *
+ * @QCA_DISCONNECT_REASON_UNSUPPORTED_CHANNEL_CSA: The driver disconnected from
+ * the AP on a channel switch announcement from it with an unsupported channel.
+ *
+ * @QCA_DISCONNECT_REASON_OPER_CHANNEL_DISABLED_INDOOR: On a concurrent AP start
+ * with indoor channels disabled and if the STA is connected on one of these
+ * disabled channels, the host driver disconnected the STA with this reason
+ * code.
+ *
+ * @QCA_DISCONNECT_REASON_OPER_CHANNEL_USER_DISABLED: Disconnection due to an
+ * explicit request from the user to disable the current operating channel.
+ *
+ * @QCA_DISCONNECT_REASON_DEVICE_RECOVERY: STA disconnected from the AP due to
+ * the internal host driver/firmware recovery.
+ *
+ * @QCA_DISCONNECT_REASON_KEY_TIMEOUT: The driver triggered the disconnection on
+ * a timeout for the key installations from the user space.
+ *
+ * @QCA_DISCONNECT_REASON_OPER_CHANNEL_BAND_CHANGE: The dDriver disconnected the
+ * STA on a band change request from the user space to a different band from the
+ * current operation channel/band.
+ *
+ * @QCA_DISCONNECT_REASON_IFACE_DOWN: The STA disconnected from the AP on an
+ * interface down trigger from the user space.
+ *
+ * @QCA_DISCONNECT_REASON_PEER_XRETRY_FAIL: The host driver disconnected the
+ * STA on getting continuous transmission failures for multiple Data frames.
+ *
+ * @QCA_DISCONNECT_REASON_PEER_INACTIVITY: The STA does a keep alive
+ * notification to the AP by transmitting NULL/G-ARP frames. This disconnection
+ * represents inactivity from AP on such transmissions.
+
+ * @QCA_DISCONNECT_REASON_SA_QUERY_TIMEOUT: This reason code is used on
+ * disconnection when SA Query times out (AP does not respond to SA Query).
+ *
+ * @QCA_DISCONNECT_REASON_BEACON_MISS_FAILURE: The host driver disconnected the
+ * STA on missing the beacons continuously from the AP.
+ *
+ * @QCA_DISCONNECT_REASON_CHANNEL_SWITCH_FAILURE: Disconnection due to STA not
+ * able to move to the channel mentioned by the AP in CSA.
+ *
+ * @QCA_DISCONNECT_REASON_USER_TRIGGERED: User triggered disconnection.
+ */
+enum qca_disconnect_reason_codes {
+ QCA_DISCONNECT_REASON_UNSPECIFIED = 0,
+ QCA_DISCONNECT_REASON_INTERNAL_ROAM_FAILURE = 1,
+ QCA_DISCONNECT_REASON_EXTERNAL_ROAM_FAILURE = 2,
+ QCA_DISCONNECT_REASON_GATEWAY_REACHABILITY_FAILURE = 3,
+ QCA_DISCONNECT_REASON_UNSUPPORTED_CHANNEL_CSA = 4,
+ QCA_DISCONNECT_REASON_OPER_CHANNEL_DISABLED_INDOOR = 5,
+ QCA_DISCONNECT_REASON_OPER_CHANNEL_USER_DISABLED = 6,
+ QCA_DISCONNECT_REASON_DEVICE_RECOVERY = 7,
+ QCA_DISCONNECT_REASON_KEY_TIMEOUT = 8,
+ QCA_DISCONNECT_REASON_OPER_CHANNEL_BAND_CHANGE = 9,
+ QCA_DISCONNECT_REASON_IFACE_DOWN = 10,
+ QCA_DISCONNECT_REASON_PEER_XRETRY_FAIL = 11,
+ QCA_DISCONNECT_REASON_PEER_INACTIVITY = 12,
+ QCA_DISCONNECT_REASON_SA_QUERY_TIMEOUT = 13,
+ QCA_DISCONNECT_REASON_BEACON_MISS_FAILURE = 14,
+ QCA_DISCONNECT_REASON_CHANNEL_SWITCH_FAILURE = 15,
+ QCA_DISCONNECT_REASON_USER_TRIGGERED = 16,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_driver_disconnect_reason - Defines attributes
+ * used by %QCA_NL80211_VENDOR_SUBCMD_DRIVER_DISCONNECT_REASON vendor command.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASCON_CODE: u32 attribute.
+ * This attribute represents the driver specific reason codes (local
+ * driver/firmware initiated reasons for disconnection) defined
+ * in enum qca_disconnect_reason_codes.
+ */
+enum qca_wlan_vendor_attr_driver_disconnect_reason {
+ QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASCON_CODE = 1,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_MAX =
+ QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_AFTER_LAST - 1,
+};
+
#endif /* QCA_VENDOR_H */
projects / thirdparty / hostap.git / blobdiff