--- /dev/null
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6xxx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell MV88E6xxx DSA switch family
+
+maintainers:
+ - Andrew Lunn <andrew@lunn.ch>
+
+description:
+ The Marvell MV88E6xxx switch series has been produced and sold
+ by Marvell since at least 2008. The switch has a few compatibles which
+ just indicate the base address of the switch, then operating systems
+ can investigate switch ID registers to find out which actual version
+ of the switch it is dealing with.
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - marvell,mv88e6085
+ - marvell,mv88e6190
+ - marvell,mv88e6250
+ description: |
+ marvell,mv88e6085: This switch uses base address 0x10.
+ This switch and its siblings will be autodetected from
+ ID registers found in the switch, so only "marvell,mv88e6085" should be
+ specified. This includes the following list of MV88Exxxx switches:
+ 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, 6171, 6172, 6175, 6176,
+ 6185, 6240, 6320, 6321, 6341, 6350, 6351, 6352
+ marvell,mv88e6190: This switch uses base address 0x00.
+ This switch and its siblings will be autodetected from
+ ID registers found in the switch, so only "marvell,mv88e6190" should be
+ specified. This includes the following list of MV88Exxxx switches:
+ 6190, 6190X, 6191, 6290, 6361, 6390, 6390X
+ marvell,mv88e6250: This switch uses base address 0x08 or 0x18.
+ This switch and its siblings will be autodetected from
+ ID registers found in the switch, so only "marvell,mv88e6250" should be
+ specified. This includes the following list of MV88Exxxx switches:
+ 6220, 6250
+ - items:
+ - const: marvell,turris-mox-mv88e6085
+ - const: marvell,mv88e6085
+ - items:
+ - const: marvell,turris-mox-mv88e6190
+ - const: marvell,mv88e6190
+
+ reg:
+ maxItems: 1
+
+ eeprom-length:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Set to the length of an EEPROM connected to the switch. Must be
+ set if the switch can not detect the presence and/or size of a connected
+ EEPROM, otherwise optional.
+
+ reset-gpios:
+ description:
+ GPIO to be used to reset the whole device
+ maxItems: 1
+
+ interrupts:
+ description: The switch provides an external interrupt line, but it is
+ not always used by target systems.
+ maxItems: 1
+
+ interrupt-controller:
+ description: The switch has an internal interrupt controller used by
+ the different sub-blocks.
+
+ '#interrupt-cells':
+ description: The internal interrupt controller only supports triggering
+ on active high level interrupts so the second cell must alway be set to
+ IRQ_TYPE_LEVEL_HIGH.
+ const: 2
+
+ mdio:
+ $ref: /schemas/net/mdio.yaml#
+ unevaluatedProperties: false
+ description: Marvell MV88E6xxx switches have an varying combination of
+ internal and external MDIO buses, in some cases a combined bus that
+ can be used both internally and externally. This node is for the
+ primary bus, used internally and sometimes also externally.
+
+ mdio-external:
+ $ref: /schemas/net/mdio.yaml#
+ unevaluatedProperties: false
+ description: Marvell MV88E6xxx switches that have a separate external
+ MDIO bus use this port to access external components on the MDIO bus.
+
+ properties:
+ compatible:
+ const: marvell,mv88e6xxx-mdio-external
+
+ required:
+ - compatible
+
+allOf:
+ - $ref: dsa.yaml#/$defs/ethernet-ports
+
+required:
+ - compatible
+ - reg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-switch@0 {
+ compatible = "marvell,mv88e6085";
+ reg = <0>;
+ reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sw_phy0: ethernet-phy@0 {
+ reg = <0x0>;
+ };
+
+ sw_phy1: ethernet-phy@1 {
+ reg = <0x1>;
+ };
+
+ sw_phy2: ethernet-phy@2 {
+ reg = <0x2>;
+ };
+
+ sw_phy3: ethernet-phy@3 {
+ reg = <0x3>;
+ };
+ };
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-port@0 {
+ reg = <0>;
+ label = "lan4";
+ phy-handle = <&sw_phy0>;
+ phy-mode = "internal";
+ };
+
+ ethernet-port@1 {
+ reg = <1>;
+ label = "lan3";
+ phy-handle = <&sw_phy1>;
+ phy-mode = "internal";
+ };
+
+ ethernet-port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-handle = <&sw_phy2>;
+ phy-mode = "internal";
+ };
+
+ ethernet-port@3 {
+ reg = <3>;
+ label = "lan1";
+ phy-handle = <&sw_phy3>;
+ phy-mode = "internal";
+ };
+
+ ethernet-port@5 {
+ reg = <5>;
+ ethernet = <&fec>;
+ phy-mode = "rgmii-id";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-switch@0 {
+ compatible = "marvell,mv88e6190";
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ interrupt-parent = <&gpio1>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&switch_interrupt_pins>;
+ pinctrl-names = "default";
+ reg = <0>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch0phy1: ethernet-phy@1 {
+ reg = <0x1>;
+ };
+
+ switch0phy2: ethernet-phy@2 {
+ reg = <0x2>;
+ };
+
+ switch0phy3: ethernet-phy@3 {
+ reg = <0x3>;
+ };
+
+ switch0phy4: ethernet-phy@4 {
+ reg = <0x4>;
+ };
+
+ switch0phy5: ethernet-phy@5 {
+ reg = <0x5>;
+ };
+
+ switch0phy6: ethernet-phy@6 {
+ reg = <0x6>;
+ };
+
+ switch0phy7: ethernet-phy@7 {
+ reg = <0x7>;
+ };
+
+ switch0phy8: ethernet-phy@8 {
+ reg = <0x8>;
+ };
+ };
+
+ mdio-external {
+ compatible = "marvell,mv88e6xxx-mdio-external";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy1: ethernet-phy@b {
+ reg = <0xb>;
+ compatible = "ethernet-phy-ieee802.3-c45";
+ };
+
+ phy2: ethernet-phy@c {
+ reg = <0xc>;
+ compatible = "ethernet-phy-ieee802.3-c45";
+ };
+ };
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-port@0 {
+ ethernet = <ð0>;
+ phy-mode = "rgmii";
+ reg = <0>;
+
+ fixed-link {
+ full-duplex;
+ pause;
+ speed = <1000>;
+ };
+ };
+
+ ethernet-port@1 {
+ label = "lan1";
+ phy-handle = <&switch0phy1>;
+ reg = <1>;
+ };
+
+ ethernet-port@2 {
+ label = "lan2";
+ phy-handle = <&switch0phy2>;
+ reg = <2>;
+ };
+
+ ethernet-port@3 {
+ label = "lan3";
+ phy-handle = <&switch0phy3>;
+ reg = <3>;
+ };
+
+ ethernet-port@4 {
+ label = "lan4";
+ phy-handle = <&switch0phy4>;
+ reg = <4>;
+ };
+
+ ethernet-port@5 {
+ label = "lan5";
+ phy-handle = <&switch0phy5>;
+ reg = <5>;
+ };
+
+ ethernet-port@6 {
+ label = "lan6";
+ phy-handle = <&switch0phy6>;
+ reg = <6>;
+ };
+
+ ethernet-port@7 {
+ label = "lan7";
+ phy-handle = <&switch0phy7>;
+ reg = <7>;
+ };
+
+ ethernet-port@8 {
+ label = "lan8";
+ phy-handle = <&switch0phy8>;
+ reg = <8>;
+ };
+
+ ethernet-port@9 {
+ /* 88X3310P external phy */
+ label = "lan9";
+ phy-handle = <&phy1>;
+ phy-mode = "xaui";
+ reg = <9>;
+ };
+
+ ethernet-port@a {
+ /* 88X3310P external phy */
+ label = "lan10";
+ phy-handle = <&phy2>;
+ phy-mode = "xaui";
+ reg = <0xa>;
+ };
+ };
+ };
+ };
+++ /dev/null
-Marvell DSA Switch Device Tree Bindings
----------------------------------------
-
-WARNING: This binding is currently unstable. Do not program it into a
-FLASH never to be changed again. Once this binding is stable, this
-warning will be removed.
-
-If you need a stable binding, use the old dsa.txt binding.
-
-Marvell Switches are MDIO devices. The following properties should be
-placed as a child node of an mdio device.
-
-The properties described here are those specific to Marvell devices.
-Additional required and optional properties can be found in dsa.txt.
-
-The compatibility string is used only to find an identification register,
-which is at a different MDIO base address in different switch families.
-- "marvell,mv88e6085" : Switch has base address 0x10. Use with models:
- 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165,
- 6171, 6172, 6175, 6176, 6185, 6240, 6320, 6321,
- 6341, 6350, 6351, 6352
-- "marvell,mv88e6190" : Switch has base address 0x00. Use with models:
- 6190, 6190X, 6191, 6290, 6361, 6390, 6390X
-- "marvell,mv88e6250" : Switch has base address 0x08 or 0x18. Use with model:
- 6220, 6250
-
-Required properties:
-- compatible : Should be one of "marvell,mv88e6085",
- "marvell,mv88e6190" or "marvell,mv88e6250" as
- indicated above
-- reg : Address on the MII bus for the switch.
-
-Optional properties:
-
-- reset-gpios : Should be a gpio specifier for a reset line
-- interrupts : Interrupt from the switch
-- interrupt-controller : Indicates the switch is itself an interrupt
- controller. This is used for the PHY interrupts.
-#interrupt-cells = <2> : Controller uses two cells, number and flag
-- eeprom-length : Set to the length of an EEPROM connected to the
- switch. Must be set if the switch can not detect
- the presence and/or size of a connected EEPROM,
- otherwise optional.
-- mdio : Container of PHY and devices on the switches MDIO
- bus.
-- mdio? : Container of PHYs and devices on the external MDIO
- bus. The node must contains a compatible string of
- "marvell,mv88e6xxx-mdio-external"
-
-Example:
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- interrupt-parent = <&gpio0>;
- interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <2>;
-
- switch0: switch@0 {
- compatible = "marvell,mv88e6085";
- reg = <0>;
- reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- switch1phy0: switch1phy0@0 {
- reg = <0>;
- interrupt-parent = <&switch0>;
- interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
- };
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- interrupt-parent = <&gpio0>;
- interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <2>;
-
- switch0: switch@0 {
- compatible = "marvell,mv88e6190";
- reg = <0>;
- reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- switch1phy0: switch1phy0@0 {
- reg = <0>;
- interrupt-parent = <&switch0>;
- interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
- };
- };
-
- mdio1 {
- compatible = "marvell,mv88e6xxx-mdio-external";
- #address-cells = <1>;
- #size-cells = <0>;
- switch1phy9: switch1phy0@9 {
- reg = <9>;
- };
- };
- };
- };
projects / thirdparty / linux.git / commitdiff
