board/raidsonic/ib62x0/kwbimage.cfg

   1 # SPDX-License-Identifier: GPL-2.0+
   2 #
   3 # Copyright (C) 2011-2012
   4 # Gerald Kerma <dreagle@doukki.net>
   5 # Simon Baatz <gmbnomis@gmail.com>
   6 # Luka Perkov <luka@openwrt.org>
   7 # Refer doc/README.kwbimage for more details about how-to configure
   8 # and create kirkwood boot image
   9 #
  10
  11 # Boot Media configurations
  12 BOOT_FROM       nand
  13 NAND_ECC_MODE   default
  14 NAND_PAGE_SIZE  0x0800
  15
  16 # SOC registers configuration using bootrom header extension
  17 # Maximum KWBIMAGE_MAX_CONFIG configurations allowed
  18
  19 # Configure RGMII-0 interface pad voltage to 1.8V
  20 DATA 0xffd100e0 0x1b1b1b9b
  21
  22 # Dram initalization for SINGLE x16 CL=5 @ 400MHz
  23 DATA 0xffd01400 0x43000c30      # DDR Configuration register
  24 # bit13-0:  0xc30, (3120 DDR2 clks refresh rate)
  25 # bit23-14: 0x0,
  26 # bit24:    0x1,   enable exit self refresh mode on DDR access
  27 # bit25:    0x1,   required
  28 # bit29-26: 0x0,
  29 # bit31-30: 0x1,
  30
  31 DATA 0xffd01404 0x37543000      # DDR Controller Control Low
  32 # bit4:     0x0, addr/cmd in smame cycle
  33 # bit5:     0x0, clk is driven during self refresh, we don't care for APX
  34 # bit6:     0x0, use recommended falling edge of clk for addr/cmd
  35 # bit14:    0x0, input buffer always powered up
  36 # bit18:    0x1, cpu lock transaction enabled
  37 # bit23-20: 0x5, recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
  38 # bit27-24: 0x7, CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
  39 # bit30-28: 0x3, required
  40 # bit31:    0x0, no additional STARTBURST delay
  41
  42 DATA 0xffd01408 0x22125451      # DDR Timing (Low) (active cycles value +1)
  43 # bit3-0:   TRAS lsbs
  44 # bit7-4:   TRCD
  45 # bit11-8:  TRP
  46 # bit15-12: TWR
  47 # bit19-16: TWTR
  48 # bit20:    TRAS msb
  49 # bit23-21: 0x0
  50 # bit27-24: TRRD
  51 # bit31-28: TRTP
  52
  53 DATA 0xffd0140c 0x00000a33      # DDR Timing (High)
  54 # bit6-0:   TRFC
  55 # bit8-7:   TR2R
  56 # bit10-9:  TR2W
  57 # bit12-11: TW2W
  58 # bit31-13: 0x0, required
  59
  60 DATA 0xffd01410 0x0000000c      # DDR Address Control
  61 # bit1-0:   00,  Cs0width (x8)
  62 # bit3-2:   11,  Cs0size (1Gb)
  63 # bit5-4:   00,  Cs1width (x8)
  64 # bit7-6:   11,  Cs1size (1Gb)
  65 # bit9-8:   00,  Cs2width (nonexistent)
  66 # bit11-10: 00,  Cs2size (nonexistent)
  67 # bit13-12: 00,  Cs3width (nonexistent)
  68 # bit15-14: 00,  Cs3size (nonexistent)
  69 # bit16:    0,   Cs0AddrSel
  70 # bit17:    0,   Cs1AddrSel
  71 # bit18:    0,   Cs2AddrSel
  72 # bit19:    0,   Cs3AddrSel
  73 # bit31-20: 0x0, required
  74
  75 DATA 0xffd01414 0x00000000      # DDR Open Pages Control
  76 # bit0:    0,   OpenPage enabled
  77 # bit31-1: 0x0, required
  78
  79 DATA 0xffd01418 0x00000000      # DDR Operation
  80 # bit3-0:   0x0, DDR cmd
  81 # bit31-4:  0x0, required
  82
  83 DATA 0xffd0141c 0x00000c52      # DDR Mode
  84 # bit2-0:   0x2, BurstLen=2 required
  85 # bit3:     0x0, BurstType=0 required
  86 # bit6-4:   0x4, CL=5
  87 # bit7:     0x0, TestMode=0 normal
  88 # bit8:     0x0, DLL reset=0 normal
  89 # bit11-9:  0x6, auto-precharge write recovery
  90 # bit12:    0x0, PD must be zero
  91 # bit31-13: 0x0, required
  92
  93 DATA 0xffd01420 0x00000040      # DDR Extended Mode
  94 # bit0:     0,   DDR DLL enabled
  95 # bit1:     0,   DDR drive strenght normal
  96 # bit2:     1,   DDR ODT control lsd (disabled)
  97 # bit5-3:   0x0, required
  98 # bit6:     0,   DDR ODT control msb, (disabled)
  99 # bit9-7:   0x0, required
 100 # bit10:    0,   differential DQS enabled
 101 # bit11:    0,   required
 102 # bit12:    0,   DDR output buffer enabled
 103 # bit31-13: 0x0, required
 104
 105 DATA 0xffd01424 0x0000f17f      # DDR Controller Control High
 106 # bit2-0:   0x7, required
 107 # bit3:     0x1, MBUS Burst Chop disabled
 108 # bit6-4:   0x7, required
 109 # bit7:     0x0,
 110 # bit8:     0x1, add writepath sample stage, must be 1 for DDR freq >= 300MHz
 111 # bit9:     0x0, no half clock cycle addition to dataout
 112 # bit10:    0x0, 1/4 clock cycle skew enabled for addr/ctl signals
 113 # bit11:    0x0, 1/4 clock cycle skew disabled for write mesh
 114 # bit15-12: 0xf, required
 115 # bit31-16: 0,   required
 116
 117 DATA 0xffd01428 0x00085520      # DDR2 ODT Read Timing (default values)
 118 DATA 0xffd0147c 0x00008552      # DDR2 ODT Write Timing (default values)
 119
 120 DATA 0xffd01500 0x00000000      # CS[0]n Base address to 0x0
 121 DATA 0xffd01504 0x0ffffff1      # CS[0]n Size
 122 # bit0:     0x1,     Window enabled
 123 # bit1:     0x0,     Write Protect disabled
 124 # bit3-2:   0x0,     CS0 hit selected
 125 # bit23-4:  0xfffff, required
 126 # bit31-24: 0x0f,    Size (i.e. 256MB)
 127
 128 DATA 0xffd01508 0x10000000      # CS[1]n Base address to 256Mb
 129 DATA 0xffd0150c 0x00000000      # CS[1]n Size, window disabled
 130
 131 DATA 0xffd01514 0x00000000      # CS[2]n Size, window disabled
 132 DATA 0xffd0151c 0x00000000      # CS[3]n Size, window disabled
 133
 134 DATA 0xffd01494 0x00030000      # DDR ODT Control (Low)
 135 # bit3-0:     ODT0Rd, MODT[0] asserted during read from DRAM CS1
 136 # bit7-4:     ODT0Rd, MODT[0] asserted during read from DRAM CS0
 137 # bit19-16:2, ODT0Wr, MODT[0] asserted during write to DRAM CS1
 138 # bit23-20:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
 139
 140 DATA 0xffd01498 0x00000000      # DDR ODT Control (High)
 141 # bit1-0:  0x0, ODT0 controlled by ODT Control (low) register above
 142 # bit3-2:  0x1, ODT1 active NEVER!
 143 # bit31-4: 0x0, required
 144
 145 DATA 0xffd0149c 0x0000e803      # CPU ODT Control
 146 DATA 0xffd01480 0x00000001      # DDR Initialization Control
 147 # bit0: 0x1, enable DDR init upon this register write
 148
 149 DATA 0xffd20134 0x66666666      # L2 RAM Timing 0 Register
 150 DATA 0xffd20138 0x66666666      # L2 RAM Timing 1 Register
 151
 152 # End of Header extension
 153 DATA 0x0 0x0