&& strcmp (abfd->xvec->name, "coff-Intel-little") != 0
&& strcmp (abfd->xvec->name, "coff-Intel-big") != 0)
{
-#if 1
/* For m68k-coff, the addend was being subtracted twice during
relocation with -r. Removing the line below this comment
fixes that problem; see PR 2953.
right
*/
relocation -= reloc_entry->addend;
-#endif
reloc_entry->addend = 0;
}
else
&& strcmp (abfd->xvec->name, "coff-Intel-little") != 0
&& strcmp (abfd->xvec->name, "coff-Intel-big") != 0)
{
-#if 1
-/* For m68k-coff, the addend was being subtracted twice during
- relocation with -r. Removing the line below this comment
- fixes that problem; see PR 2953.
+
+ /* For m68k-coff, the addend was being subtracted twice during
+ relocation with -r. Removing the line below this comment
+ fixes that problem; see PR 2953.
However, Ian wrote the following, regarding removing the line below,
which explains why it is still enabled: --djm
7) if they are different you have to figure out which version is
right. */
relocation -= reloc_entry->addend;
-#endif
reloc_entry->addend = 0;
}
else
BFD_RELOC_FRV_GOTOFFHI
ENUMX
BFD_RELOC_FRV_GOTOFFLO
+ENUMX
+ BFD_RELOC_FRV_GETTLSOFF
+ENUMX
+ BFD_RELOC_FRV_TLSDESC_VALUE
+ENUMX
+ BFD_RELOC_FRV_GOTTLSDESC12
+ENUMX
+ BFD_RELOC_FRV_GOTTLSDESCHI
+ENUMX
+ BFD_RELOC_FRV_GOTTLSDESCLO
+ENUMX
+ BFD_RELOC_FRV_TLSMOFF12
+ENUMX
+ BFD_RELOC_FRV_TLSMOFFHI
+ENUMX
+ BFD_RELOC_FRV_TLSMOFFLO
+ENUMX
+ BFD_RELOC_FRV_GOTTLSOFF12
+ENUMX
+ BFD_RELOC_FRV_GOTTLSOFFHI
+ENUMX
+ BFD_RELOC_FRV_GOTTLSOFFLO
+ENUMX
+ BFD_RELOC_FRV_TLSOFF
+ENUMX
+ BFD_RELOC_FRV_TLSDESC_RELAX
+ENUMX
+ BFD_RELOC_FRV_GETTLSOFF_RELAX
+ENUMX
+ BFD_RELOC_FRV_TLSOFF_RELAX
+ENUMX
+ BFD_RELOC_FRV_TLSMOFF
ENUMDOC
Fujitsu Frv Relocations.
COMMENT
BFD_RELOC_ARM_OFFSET_IMM
ENUMX
BFD_RELOC_ARM_SHIFT_IMM
+ENUMX
+ BFD_RELOC_ARM_SMI
ENUMX
BFD_RELOC_ARM_SWI
ENUMX
ENUMDOC
These relocs are only used within the ARM assembler. They are not
(at present) written to any object files.
+ENUM
+ BFD_RELOC_ARM_TARGET1
+ENUMDOC
+ Pc-relative or absolute relocation depending on target. Used for
+ entries in .init_array sections.
+ENUM
+ BFD_RELOC_ARM_ROSEGREL32
+ENUMDOC
+ Read-only segment base relative address.
+ENUM
+ BFD_RELOC_ARM_SBREL32
+ENUMDOC
+ Data segment base relative address.
+ENUM
+ BFD_RELOC_ARM_TARGET2
+ENUMDOC
+ This reloc is used for References to RTTI dta from exception handling
+ tables. The actual definition depends on the target. It may be a
+ pc-relative or some form of GOT-indirect relocation.
+ENUM
+ BFD_RELOC_ARM_PREL31
+ENUMDOC
+ 31-bit PC relative address.
ENUM
BFD_RELOC_SH_PCDISP8BY2
ENUMX
BFD_RELOC_SH_PCDISP12BY2
+ENUMX
+ BFD_RELOC_SH_IMM3
+ENUMX
+ BFD_RELOC_SH_IMM3U
+ENUMX
+ BFD_RELOC_SH_DISP12
+ENUMX
+ BFD_RELOC_SH_DISP12BY2
+ENUMX
+ BFD_RELOC_SH_DISP12BY4
+ENUMX
+ BFD_RELOC_SH_DISP12BY8
+ENUMX
+ BFD_RELOC_SH_DISP20
+ENUMX
+ BFD_RELOC_SH_DISP20BY8
ENUMX
BFD_RELOC_SH_IMM4
ENUMX
BFD_RELOC_V850_ALIGN
ENUMDOC
Used to maintain alignment whilst relaxing.
+ENUM
+ BFD_RELOC_V850_LO16_SPLIT_OFFSET
+ENUMDOC
+ This is a variation of BFD_RELOC_LO16 that can be used in v850e ld.bu
+ instructions.
ENUM
BFD_RELOC_MN10300_32_PCREL
ENUMDOC
ENUMDOC
This is a 32 bit reloc for the AVR that stores 23 bit value
into 22 bits.
+ENUM
+ BFD_RELOC_AVR_LDI
+ENUMDOC
+ This is a 16 bit reloc for the AVR that stores all needed bits
+ for absolute addressing with ldi with overflow check to linktime
+ENUM
+ BFD_RELOC_AVR_6
+ENUMDOC
+ This is a 6 bit reloc for the AVR that stores offset for ldd/std
+ instructions
+ENUM
+ BFD_RELOC_AVR_6_ADIW
+ENUMDOC
+ This is a 6 bit reloc for the AVR that stores offset for adiw/sbiw
+ instructions
ENUM
BFD_RELOC_390_12
ENUMDOC
NS CR16C Relocations.
+ENUM
+ BFD_RELOC_CRX_REL4
+ENUMX
+ BFD_RELOC_CRX_REL8
+ENUMX
+ BFD_RELOC_CRX_REL8_CMP
+ENUMX
+ BFD_RELOC_CRX_REL16
+ENUMX
+ BFD_RELOC_CRX_REL24
+ENUMX
+ BFD_RELOC_CRX_REL32
+ENUMX
+ BFD_RELOC_CRX_REGREL12
+ENUMX
+ BFD_RELOC_CRX_REGREL22
+ENUMX
+ BFD_RELOC_CRX_REGREL28
+ENUMX
+ BFD_RELOC_CRX_REGREL32
+ENUMX
+ BFD_RELOC_CRX_ABS16
+ENUMX
+ BFD_RELOC_CRX_ABS32
+ENUMX
+ BFD_RELOC_CRX_NUM8
+ENUMX
+ BFD_RELOC_CRX_NUM16
+ENUMX
+ BFD_RELOC_CRX_NUM32
+ENUMX
+ BFD_RELOC_CRX_IMM16
+ENUMX
+ BFD_RELOC_CRX_IMM32
+ENUMX
+ BFD_RELOC_CRX_SWITCH8
+ENUMX
+ BFD_RELOC_CRX_SWITCH16
+ENUMX
+ BFD_RELOC_CRX_SWITCH32
+ENUMDOC
+ NS CRX Relocations.
+
ENUM
BFD_RELOC_CRIS_BDISP8
ENUMX
BFD_RELOC_CRIS_SIGNED_6
ENUMX
BFD_RELOC_CRIS_UNSIGNED_6
+ENUMX
+ BFD_RELOC_CRIS_SIGNED_8
+ENUMX
+ BFD_RELOC_CRIS_UNSIGNED_8
+ENUMX
+ BFD_RELOC_CRIS_SIGNED_16
+ENUMX
+ BFD_RELOC_CRIS_UNSIGNED_16
+ENUMX
+ BFD_RELOC_CRIS_LAPCQ_OFFSET
ENUMX
BFD_RELOC_CRIS_UNSIGNED_4
ENUMDOC
BFD_RELOC_MSP430_16_PCREL_BYTE
ENUMX
BFD_RELOC_MSP430_16_BYTE
+ENUMX
+ BFD_RELOC_MSP430_2X_PCREL
+ENUMX
+ BFD_RELOC_MSP430_RL_PCREL
ENUMDOC
msp430 specific relocation codes
ENUMDOC
Xtensa relocation used in ELF object files for symbols that may require
PLT entries. Otherwise, this is just a generic 32-bit relocation.
+ENUM
+ BFD_RELOC_XTENSA_DIFF8
+ENUMX
+ BFD_RELOC_XTENSA_DIFF16
+ENUMX
+ BFD_RELOC_XTENSA_DIFF32
+ENUMDOC
+ Xtensa relocations to mark the difference of two local symbols.
+ These are only needed to support linker relaxation and can be ignored
+ when not relaxing. The field is set to the value of the difference
+ assuming no relaxation. The relocation encodes the position of the
+ first symbol so the linker can determine whether to adjust the field
+ value.
+ENUM
+ BFD_RELOC_XTENSA_SLOT0_OP
+ENUMX
+ BFD_RELOC_XTENSA_SLOT1_OP
+ENUMX
+ BFD_RELOC_XTENSA_SLOT2_OP
+ENUMX
+ BFD_RELOC_XTENSA_SLOT3_OP
+ENUMX
+ BFD_RELOC_XTENSA_SLOT4_OP
+ENUMX
+ BFD_RELOC_XTENSA_SLOT5_OP
+ENUMX
+ BFD_RELOC_XTENSA_SLOT6_OP
+ENUMX
+ BFD_RELOC_XTENSA_SLOT7_OP
+ENUMX
+ BFD_RELOC_XTENSA_SLOT8_OP
+ENUMX
+ BFD_RELOC_XTENSA_SLOT9_OP
+ENUMX
+ BFD_RELOC_XTENSA_SLOT10_OP
+ENUMX
+ BFD_RELOC_XTENSA_SLOT11_OP
+ENUMX
+ BFD_RELOC_XTENSA_SLOT12_OP
+ENUMX
+ BFD_RELOC_XTENSA_SLOT13_OP
+ENUMX
+ BFD_RELOC_XTENSA_SLOT14_OP
+ENUMDOC
+ Generic Xtensa relocations for instruction operands. Only the slot
+ number is encoded in the relocation. The relocation applies to the
+ last PC-relative immediate operand, or if there are no PC-relative
+ immediates, to the last immediate operand.
+ENUM
+ BFD_RELOC_XTENSA_SLOT0_ALT
+ENUMX
+ BFD_RELOC_XTENSA_SLOT1_ALT
+ENUMX
+ BFD_RELOC_XTENSA_SLOT2_ALT
+ENUMX
+ BFD_RELOC_XTENSA_SLOT3_ALT
+ENUMX
+ BFD_RELOC_XTENSA_SLOT4_ALT
+ENUMX
+ BFD_RELOC_XTENSA_SLOT5_ALT
+ENUMX
+ BFD_RELOC_XTENSA_SLOT6_ALT
+ENUMX
+ BFD_RELOC_XTENSA_SLOT7_ALT
+ENUMX
+ BFD_RELOC_XTENSA_SLOT8_ALT
+ENUMX
+ BFD_RELOC_XTENSA_SLOT9_ALT
+ENUMX
+ BFD_RELOC_XTENSA_SLOT10_ALT
+ENUMX
+ BFD_RELOC_XTENSA_SLOT11_ALT
+ENUMX
+ BFD_RELOC_XTENSA_SLOT12_ALT
+ENUMX
+ BFD_RELOC_XTENSA_SLOT13_ALT
+ENUMX
+ BFD_RELOC_XTENSA_SLOT14_ALT
+ENUMDOC
+ Alternate Xtensa relocations. Only the slot is encoded in the
+ relocation. The meaning of these relocations is opcode-specific.
ENUM
BFD_RELOC_XTENSA_OP0
ENUMX
ENUMX
BFD_RELOC_XTENSA_OP2
ENUMDOC
- Generic Xtensa relocations. Only the operand number is encoded
- in the relocation. The details are determined by extracting the
- instruction opcode.
+ Xtensa relocations for backward compatibility. These have all been
+ replaced by BFD_RELOC_XTENSA_SLOT0_OP.
ENUM
BFD_RELOC_XTENSA_ASM_EXPAND
ENUMDOC
break;
case bfd_reloc_overflow:
if (!((*link_info->callbacks->reloc_overflow)
- (link_info, bfd_asymbol_name (*(*parent)->sym_ptr_ptr),
+ (link_info, NULL,
+ bfd_asymbol_name (*(*parent)->sym_ptr_ptr),
(*parent)->howto->name, (*parent)->addend,
input_bfd, input_section, (*parent)->address)))
goto error_return;
projects / thirdparty / binutils-gdb.git / blobdiff