daily update

[thirdparty/binutils-gdb.git] / gdb / testsuite / gdb.gdb / complaints.exp

diff --git a/gdb/testsuite/gdb.gdb/complaints.exp b/gdb/testsuite/gdb.gdb/complaints.exp
index cc66e309727acac1239981f68292732532ac10e9..e5f6e4ae19e66a2f91c16b1a3420f9107fbee21b 100644 (file)
--- a/gdb/testsuite/gdb.gdb/complaints.exp
+++ b/gdb/testsuite/gdb.gdb/complaints.exp
@@ -1,4 +1,4 @@
-# Copyright 2002, 2004, 2007, 2008, 2009, 2010 Free Software Foundation, Inc.
+# Copyright 2002-2013 Free Software Foundation, Inc.
 
 # This program is free software; you can redistribute it and/or modify
 # it under the terms of the GNU General Public License as published by
@@ -17,88 +17,13 @@
 # derived from xfullpath.exp (written by Joel Brobecker), derived from
 # selftest.exp (written by Rob Savoye).
 
-if $tracelevel then {
-    strace $tracelevel
-}
-
+load_lib selftest-support.exp
 
-# are we on a target board
-if { [is_remote target] || ![isnative] } then {
+if [target_info exists gdb,noinferiorio] {
+    verbose "Skipping because of no inferiorio capabilities."
     return
 }
 
-proc setup_test { executable } {
-    global gdb_prompt
-    global timeout
-
-    # load yourself into the debugger
-    # This can take a relatively long time, particularly for testing where
-    # the executable is being accessed over a network, or where gdb does not
-    # support partial symbols for a particular target and has to load the
-    # entire symbol table.  Set the timeout to 10 minutes, which should be
-    # adequate for most environments (it *has* timed out with 5 min on a
-    # SPARCstation SLC under moderate load, so this isn't unreasonable).
-    # After gdb is started, set the timeout to 30 seconds for the duration
-    # of this test, and then back to the original value.
-
-    set oldtimeout $timeout
-    set timeout 600
-    verbose "Timeout is now $timeout seconds" 2
-
-    global gdb_file_cmd_debug_info
-    set gdb_file_cmd_debug_info "unset"
-
-    set result [gdb_load $executable]
-    set timeout $oldtimeout
-    verbose "Timeout is now $timeout seconds" 2
-
-    if { $result != 0 } then {
-       return -1
-    }
-
-    if { $gdb_file_cmd_debug_info != "debug" } then {
-       untested "No debug information, skipping testcase."
-       return -1
-    }
-
-    # Set a breakpoint at main
-    gdb_test "break captured_command_loop" \
-            "Breakpoint.*at.* file.*, line.*" \
-            "breakpoint in captured_command_loop"
-
-    # run yourself
-    # It may take a very long time for the inferior gdb to start (lynx),
-    # so we bump it back up for the duration of this command.
-    set timeout 600
-
-    set description "run until breakpoint at captured_command_loop"
-    gdb_test_multiple "run -nw" "$description" {
-        -re "Starting program.*Breakpoint \[0-9\]+,.*captured_command_loop .data.* at .*main.c:.*$gdb_prompt $" {
-            pass "$description"
-        }
-        -re "Starting program.*Breakpoint \[0-9\]+,.*captured_command_loop .data.*$gdb_prompt $" {
-            xfail "$description (line numbers scrambled?)"
-        }
-        -re "vfork: No more processes.*$gdb_prompt $" {
-            fail "$description (out of virtual memory)"
-            set timeout $oldtimeout
-            verbose "Timeout is now $timeout seconds" 2
-            return -1
-        }
-        -re ".*$gdb_prompt $" {
-            fail "$description"
-            set timeout $oldtimeout
-            verbose "Timeout is now $timeout seconds" 2
-            return -1
-        }
-    }
-
-    set timeout $oldtimeout
-    verbose "Timeout is now $timeout seconds" 2
-
-    return 0
-}
-
 proc test_initial_complaints { } {
 
     global gdb_prompt
@@ -207,63 +132,21 @@ proc test_empty_complaint { cmd msg } {
 
 proc test_empty_complaints { } {
 
-    test_empty_complaint "call clear_complaints(&symfile_complaints,0,0)\n" \
+    test_empty_complaint "call clear_complaints(&symfile_complaints,0,0)" \
            "empty non-verbose non-noisy clear"
-    test_empty_complaint "call clear_complaints(&symfile_complaints,1,0)\n" \
+    test_empty_complaint "call clear_complaints(&symfile_complaints,1,0)" \
            "empty verbose non-noisy clear"
-    test_empty_complaint "call clear_complaints(&symfile_complaints,1,1)\n" \
+    test_empty_complaint "call clear_complaints(&symfile_complaints,1,1)" \
            "empty verbose noisy clear"
-    test_empty_complaint "call clear_complaints(&symfile_complaints,0,1)\n" \
+    test_empty_complaint "call clear_complaints(&symfile_complaints,0,1)" \
            "empty non-verbose noisy clear"
 
     return 0
 }
 
-# Find a pathname to a file that we would execute if the shell was asked
-# to run $arg using the current PATH.
-
-proc find_gdb { arg } {
-
-    # If the arg directly specifies an existing executable file, then
-    # simply use it.
-
-    if [file executable $arg] then {
-       return $arg
-    }
-
-    set result [which $arg]
-    if [string match "/" [ string range $result 0 0 ]] then {
-       return $result
-    }
-
-    # If everything fails, just return the unqualified pathname as default
-    # and hope for best.
-
-    return $arg
-}
-
-# Run the test with self.
-# Copy the file executable file in case this OS doesn't like to edit its own
-# text space.
-
-set GDB_FULLPATH [find_gdb $GDB]
-
-# Remove any old copy lying around.
-remote_file host delete x$tool
-
-gdb_start
-
-set file [remote_download host $GDB_FULLPATH x$tool]
-
-set setup_result [setup_test $file ]
-if {$setup_result <0} then {
-    return -1
+do_self_tests captured_command_loop {
+    test_initial_complaints
+    test_serial_complaints
+    test_short_complaints
+    test_empty_complaints
 }
-
-test_initial_complaints
-test_serial_complaints
-test_short_complaints
-test_empty_complaints
-
-gdb_exit;
-catch "remote_file host delete $file";