Hanyuan Zhao [Tue, 5 Mar 2024 07:37:33 +0000 (15:37 +0800)]
cli: panic when failed to allocate memory for the history buffer
This commit simply modifies the history initialize function,
replacing the return value by panic with reasons. The calling
chains of hist_init don't have steps explicitly throwing or
dealing with the ENOMEM error, and once the init fails, the
whole system is died. Using panic here to provide error
information instead.
Tom Rini [Mon, 4 Mar 2024 15:26:17 +0000 (10:26 -0500)]
boards: Remove empty BOARD_SPECIFIC_OPTIONS
While there are currently uses for a stanza of "config BOARD_SPECIFIC_OPTIONS"
followed by "def_bool y" and a series of select/imply statements, having
this option set followed by nothing else doesn't provide anything.
Remove these stanzas.
Marek Vasut [Sat, 2 Mar 2024 22:54:02 +0000 (23:54 +0100)]
fdt: Fix bootm_low handling
According to README CFG_SYS_BOOTMAPSZ section, in case both "bootm_low" and
"bootm_size" variables are defined, "bootm_mapsize" variable is not defined
and CFG_SYS_BOOTMAPSZ macro is not defined, all data for the Linux kernel
must be between "bootm_low" and "bootm_low" + "bootm_size".
Currently, for systems with DRAM between 0x4000_0000..0x7fff_ffff and with
e.g. bootm_low=0x60000000 and bootm_size=0x10000000, the code will attempt
to reserve memory from 0x4000_0000..0x4fff_ffff, which is incorrect. This
is because "bootm_low" is not taken into consideration correctly.
The last parameter of lmb_alloc_base() is the maximum physical address of
the to be reserved LMB area. Currently this is the start of DRAM bank that
is considered for LMB area reservation + min(DRAM bank size, bootm_size).
In case bootm_low is set to non-zero, this maximum physical address has to
be shifted upward, to min(DRAM bank start + size, bootm_low + bootm_size),
otherwise the reserved memory may be below bootm_low address.
In case of multiple DRAM banks, the current change reserves top part of
the first bank, and reserves the rest of memory in the follow up banks.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tom Rini [Wed, 13 Mar 2024 14:10:25 +0000 (10:10 -0400)]
Merge patch series "Introduce basic support for TI's AM62Px SoC family"
Bryan Brattlof <bb@ti.com> says:
Hello Again Everyone!
The AM62Px is an extension of the existing Sitara AM62x low-cost family
of application processors built for Automotive and Linux Application
development. Scalable Arm Cortex-A53 performance and embedded features,
such as: multi high-definition display support, 3D-graphics
acceleration, 4K video acceleration, and extensive peripherals make the
AM62Px well-suited for a broad range of automation and industrial
application, including automotive digital instrumentation, automotive
displays, industrial HMI, and more.
Some highlights of AM62P SoC are:
* Quad-Cortex-A53s (running up to 1.4GHz) in a single cluster.
Dual/Single core variants are provided in the same package to allow HW
compatible designs.
* One Device manager Cortex-R5F for system power and resource
management, and one Cortex-R5F for Functional Safety or
general-purpose usage.
* One 3D GPU up to 50 GLFOPS
* H.264/H.265 Video Encode/Decode.
* Display support: 3x display support over OLDI/LVDS (1x OLDI-DL, 1x or
2x OLDI-SL), DSI, or DPI. Up to 3840x1080 @ 60fps resolution
* Integrated Giga-bit Ethernet switch supporting up to a total of two
external ports (TSN capable).
* 9xUARTs, 5xSPI, 6xI2C, 2xUSB2, 3xCAN-FD, 3xMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 3xMcASP for audio,
1xCSI-RX-4L for Camera, eCAP/eQEP, ePWM, among other peripherals.
* Dedicated Centralized Hardware Security Module with support for secure
boot, debug security and crypto acceleration and trusted execution
environment.
* One 32-bit DDR Subsystem that supports LPDDR4, DDR4 memory types.
* Multiple low power modes support, ex: Deep sleep, Standby, MCU-only,
enabling battery powered system design.
For those interested, more details about this SoC can be found in the
Technical Reference Manual here: https://www.ti.com/lit/pdf/spruj83
Bryan Brattlof [Tue, 12 Mar 2024 20:20:31 +0000 (15:20 -0500)]
arm: mach-k3: fixup whitespace in SPDX License IDs
The SPDX ID format usese a single space used after the
'SPDX-License-Identifier:'. Fix all files that use any other white-space
character other than a single space.
dma: ti: k3-udma: Add DMA PSIL mappings for AM62P and J722S
Add PSIL data for the AM62P and the J722S SoC family. The PSIL mapping
for the J722S is the same except for the extra instances of the CSI-RX.
So let's reuse the same file for both the AM62P and J722S.
Bryan Brattlof [Tue, 12 Mar 2024 20:20:23 +0000 (15:20 -0500)]
arm: mach-k3: invert logic for split DM firmware config
Currently, for the K3 generation of SoCs, there are more SoCs that
utilize the split firmware approach than the combined DMSC firmware.
Invert the logic to avoid adding more and more SoCs to this list.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com> Acked-by: Andrew Davis <afd@ti.com> Signed-off-by: Bryan Brattlof <bb@ti.com>
Tom Rini [Mon, 11 Mar 2024 13:22:44 +0000 (09:22 -0400)]
Merge tag 'u-boot-imx-master-20240311' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
- Use TF-A on imx8mp_beacon to fix boot regression.
- Use latest 6.8 dts for imx8mp_beacon.
- Fix the RAM initialization for phycore_imx8mp PCL-070 rev 1.
- Describe the 0087 i.mx8m mini product variant in tdx-cfg-block.
Adam Ford [Sun, 10 Mar 2024 16:59:01 +0000 (11:59 -0500)]
arm: dts: imx8mp-beacon-kit: Resync DTS with Linux 6.8
The device tree has evolved over time, so re-sync. This also
partial reverts one change on the PCIe, because U-Boot doesn't
have a proper driver. However, since the clock is configured
to generate a 100MHz reference clock by default, a proper driver
isn't really necessary.
Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com>
Adam Ford [Thu, 7 Mar 2024 11:58:58 +0000 (05:58 -0600)]
configs: imx8mp_beacon: Fall back to using TF-A
When the board was originally added, it enabled some features which
allowed it to bypass Trusted Firmware, but as the feature set of
Linux grew and more features became available, the U-Boot config
options which bypassed TF-A caused issues, so it needs to return
to the standard operating mode of using TF-A or the system no
longer boots.
Fixes: ab53bd43dbde ("arm64: imx: Add support for imx8mp-beacon-kit") Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Benjamin Hahn [Wed, 6 Mar 2024 16:18:32 +0000 (17:18 +0100)]
board: phycore_imx8mp: Use 2GHz RAM timings for PCL-070 from pcb_rev 1
We need to differ between PCL-070 and PCM-070. PCL-070 supports 2GHz RAM
timings from pcb rev 1 or newer. PCM-070 supports 2GHz RAM timings from
pcb rev 3 or newer.
Marek Vasut [Sun, 28 Jan 2024 01:19:40 +0000 (02:19 +0100)]
net: phy: Use PHY MDIO address from DT if available
In case the PHY is fully described in DT, use PHY MDIO address
from DT directly instead of always using auto-detection. This
also fixes the behavior of 'mdio list' in such DT setup, which
now prints the PHY connected to the MAC correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Maks Mishin [Thu, 29 Feb 2024 22:32:11 +0000 (01:32 +0300)]
autoboot: Add check for result of malloc_cache_aligned()
Return value of a function 'malloc_cache_aligned'
is dereferenced at autoboot.c:207 without checking for NULL,
but it is usually checked for this function.
Yang Xiwen [Wed, 28 Feb 2024 10:57:52 +0000 (18:57 +0800)]
serial: pl01x: set baudrate when probing
It is found that when DM is enabled, only generic init function is
called in .probe(). Baudrate is never honored. Add a function call
to .setbrg() when probing so that we can update the baudrate of the
serial device.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Bob Wolff [Tue, 27 Feb 2024 23:57:03 +0000 (15:57 -0800)]
Check curve_name for null to avoid crash
If mixed rsa and ecdsa keys are specified in dtsi, an rsa key can be sent
into the ecdsa verify. Without the ecdsa,curve property, this function will
crash due to lack of checking the null pointer return.
Andrew Davis [Wed, 14 Feb 2024 16:30:09 +0000 (10:30 -0600)]
arm: mach-k3: Move DRAM address of ATF for AM62/AM62a
The current address of TF-A in DRAM is just below the 512MB address line.
This means if the DRAM in a system is 512MB then TF-A is right at the
end of memory which is often reused, for instance U-Boot relocates itself
here. If a system has less than 512MB then that system wouldn't work at
all as TF-A would fail to load.
To avoid the issues above, move TF-A to the start of DRAM, which doesn't
change from system to system.
As TF-A is position independent, this has no dependency on TF-A. We
also fixup DT as needed when TF-A address is moved, so this change also
has no dependency on Linux and is fully forward/backward compatible.
Signed-off-by: Andrew Davis <afd@ti.com> Acked-by: Bryan Brattlof <bb@ti.com>
Andrew Davis [Wed, 14 Feb 2024 16:30:08 +0000 (10:30 -0600)]
arm: mach-k3: am62a: Fixup TF-A/OP-TEE reserved-memory node in FDT
The address we load TFA and OP-TEE to is configurable by
CONFIG_K3_{ATF,OPTEE}_LOAD_ADDR, but the DT nodes reserving this memory
are static. Fix that by updating this node when the loaded address
does not match the address in DT.
Signed-off-by: Andrew Davis <afd@ti.com> Acked-by: Bryan Brattlof <bb@ti.com>
Andrew Davis [Wed, 14 Feb 2024 16:30:07 +0000 (10:30 -0600)]
arm: mach-k3: am62: Fixup TF-A/OP-TEE reserved-memory node in FDT
The address we load TF-A and OP-TEE to is configurable by Kconfig
CONFIG_K3_{ATF,OPTEE}_LOAD_ADDR, but the DT nodes reserving this memory
are often statically defined. As these binaries are dynamically loadable,
and in the case of OP-TEE may not even be loaded at all, hard-coding these
addresses is not a hardware description, but rather a configuration.
If the address that U-Boot loaded TF-A or OP-TEE does not match the
address in hard-coded in DT, then fix that node address. This also handles
the case when no reserved memory for these is provided by DT, which is
more correct as explained above.
Add this fixup function, and enable it for AM62.
Signed-off-by: Andrew Davis <afd@ti.com> Acked-by: Bryan Brattlof <bb@ti.com> Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Andrew Davis [Wed, 14 Feb 2024 16:30:06 +0000 (10:30 -0600)]
arm: mach-k3: am62: Enable OF_SYSTEM_SETUP for all boards
The fixups provided by ft_system_setup() are applicable for all AM62 based
boards. Select this at the target selection level for all AM62 boards and
remove it from any specific defconfig.
Andrew Davis [Wed, 14 Feb 2024 16:30:05 +0000 (10:30 -0600)]
arm: mach-k3: Add config option for setting OP-TEE address
Much like we have for ATF, OP-TEE has a standard address that we load
it too and run it from. Add a Kconfig item for this to remove some
hard-coding and allow this address to be more easily changed.
Signed-off-by: Andrew Davis <afd@ti.com> Acked-by: Bryan Brattlof <bb@ti.com> Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Andrew Davis [Wed, 14 Feb 2024 16:30:04 +0000 (10:30 -0600)]
arm: mach-k3: Add default ATF location for AM62/AM62a
There is a default ATF load address that is used for devices that have
ATF running in SRAM. For AM62 and AM62a, ATF runs from DRAM. Instead
of having to override the address in every defconfig, make add a
default for these ATF in DRAM devices.
Signed-off-by: Andrew Davis <afd@ti.com> Acked-by: Bryan Brattlof <bb@ti.com> Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
arm: dts: k3-binman: Make optee optional as requirement
Allow boards that use ti_spl_template to not use optee part in
configuration.
Vendor can have module with 256 Mb of memory and they try to optimize
the available memory just using the essential components.
This change allow to remove tee from configuration without binman
fail.
Romain Naour [Mon, 22 Jan 2024 10:30:44 +0000 (11:30 +0100)]
arch/arm/mach-omap2/omap5/fdt.c: ft_fixup_clocks: use clock-output-names property as fallback (kernel 5.19+)
Clock names has been updated in kernel 5.19+ with the removal of
non-standard node names [1]. Due to this change, ft_opp_clock_fixups()
doesn't work anymore since ft_fixup_clocks() is looking to the clock
name and ft_opp_clock_fixups() error out with the following message:
ft_fixup_clocks failed for DSP voltage domain: <valid offset/length>
We can't use the new clock name since several clock are using the same
generic name "clock". ft_opp_clock_fixups() is looking at the clocks
node in cm_core_aon@0:
When fdt_subnode_offset() fail, we can look at clock-output-names
property as fallback since it contain the previous clock name.
libfdt doesn't provide any support to replace fdt_subnode_offset() by
a new function looking for clock-output-names property instead of the
node name. So we have to implement it in arch/arm/mach-omap2/omap5/fdt.c
for now.
Dmitry Baryshkov [Mon, 12 Feb 2024 07:37:08 +0000 (09:37 +0200)]
virtio: fix get_config / set_config for legacy VirtIO targets
The functions virtio_pci_get_config() and virtio_pci_set_config() don't
take the offset into account when reading the config space. For example
this manifests when U-Boot tries to read the MAC address of the VirtIO
networking device. It reads 6 equa bytes instead of the proper addess.
Fix those functions by taking the offset in the config space into
account.
Fixes: 4135e10732a0 ("virtio: Add virtio over pci transport driver") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tom Rini [Tue, 5 Mar 2024 13:08:31 +0000 (08:08 -0500)]
Merge patch series "Fix driver for misc/atsha204a"
Michał Barnaś <barnas@google.com> says:
Fix the driver to behave like the chip datasheet requires.
Improve wake up function to send low signal on SDA line for at least
60us as chip requires to wake up. Fix sleep function to move the chip
into sleep mode, not into idle mode. Remove unnecessary for loop,
which would never run for more than one iteration.
Michał Barnaś [Mon, 19 Feb 2024 16:32:04 +0000 (16:32 +0000)]
misc: atsha204a: fix wakeup function
The ATSHA204A chip requires SDA line to go low for at least 60us to
wake up the chip. Previous implementation did not meet this requirement
due to the NAK received on bus and not sending the zeroes.
The function to ignore the NAK and send bytes regardless is not
supported in the u-boot making it impossible to wake up the chip
this way.
Instead, the bus speed, if needed, is set to lowest value and the
message is sent to the address 0x0. This way, the address of zero
makes the SDA line go low for about 80us, meeting the required time
to wake up the chip. The zero length packet is not sent by the i2c,
so the one byte is sent to the transfer function, but only the address
is sent anyway.
After sending the zero address, the bus speed is restored to the
previous value if it was slowed down to wake up the chip.
Michał Barnaś [Mon, 19 Feb 2024 16:32:02 +0000 (16:32 +0000)]
misc: atsha204a: remove broken for loop
Some previous commit changed the continue statement to return,
making the for loop used to retry waking up the chip to always
return after one iteration. This commit removes the loop, cleaning
the code a little.
Tom Rini [Tue, 5 Mar 2024 12:08:10 +0000 (07:08 -0500)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
One fix makes the reboot more robust on some older board, another one
stabilises the initial clock setup on the A10/A20.
Two patches make sure our DRAM init does not actually change the content
of the DRAM array, which allows to use DRAM for Linux' pstore
functionality.
We get SPI support for U-Boot proper for one more SoC, that patch was
lingering around for a while, and should not affect other SoCs, so I am
merging this now.
As an added bonus, we get the defconfig file for a new board, the DT was
already synced from the kernel tree.
The CI looked happy with changes, and I tested them on five different
boards with different SoCs.
Josua Mayer [Fri, 2 Feb 2024 15:13:32 +0000 (16:13 +0100)]
arm: dts: armada-38x-solidrun-microsom: configure i2c0 bus
SolidRun Armada-388 SoM has an i2c bus supporting on-som eeprom, and
peripherals on a carrier.
armada-38x.dtsi disables this bus by default, it should be enabled by
som or carrier dts.
Linux has moved i2c0 from helios-4 board dts to som dtsi, including
status, pinctrl and clock speed.
Copy these settings from mainline.
This fixes accessing i2c bus from u-boot commandline.
The mv88e6xxx driver does not currently initialize the smi_addr field, but
instead keeps the default zero value. This leads to driver being unusable
on devices where the switch is not on address zero of the mdio bus. Fix
this problem by reading the SMI address from device tree.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz> Reviewed-by: Marek Behún <kabel@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Andrey Skvortsov [Wed, 27 Dec 2023 21:28:43 +0000 (00:28 +0300)]
sunxi: restore modified memory
Current sunxi DRAM initialisation code does several test accesses to the
DRAM array to detect aliasing effects and so determine the correct
row/column configuration. This changes the DRAM content, which breaks
use cases like soft reset and Linux's ramoops mechanism.
Fix this problem by saving and restoring the content of the DRAM cells
that is used for the test writes.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Andrey Skvortsov [Wed, 27 Dec 2023 21:28:42 +0000 (00:28 +0300)]
sunxi: reorganize mctl_mem_matches_* functions
mctl_mem_matches and mctl_mem_matches_base identical functions. To
avoid code duplication move them to dram_helpers and make
mctl_mem_matches use generic mctl_mem_matches_base.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tom Rini [Mon, 4 Mar 2024 17:02:49 +0000 (12:02 -0500)]
Merge patch series "Introduce initial TI's J784S4 and AM69 support"
Apurva Nandan <a-nandan@ti.com> says:
Hello Everyone!
This series will introduce basic support (SD and UART) support for Texas
Instruments J784S4 EVM.
The J784S4 SoC device tree patches are taken from kernel patch submissions
and will be updated as they are accepted and merged to the kernel tree.
All other patches are specific to SPL and u-boot and do not have
dependency on other trees. Appreciate a review for acceptance to u-boot
tree.
Here are some of the salient features of the J784S4 automotive grade
application processor:
The J784S4 SoC belongs to the K3 Multicore SoC architecture
platform, providing advanced system integration in automotive,
ADAS and industrial applications requiring AI at the network edge.
This SoC extends the K3 Jacinto 7 family of SoCs with focus on
raising performance and integration while providing interfaces,
memory architecture and compute performance for multi-sensor, high
concurrency applications.
Some highlights of this SoC are:
* Up to 8 Cortex-A72s, four clusters of lockstep capable dual Cortex-R5F MCUs,
4 C7x floating point vector DSPs with Matrix Multiply Accelerator(MMA) for
deep learning and CNN.
* 3D GPU: Automotive grade IMG BXS-4-64 MC1
* Vision Processing Accelerator (VPAC) with image signal processor and Depth
and Motion Processing Accelerator (DMPAC)
* Three CSI2.0 4L RX plus two CSI2.0 4L TX, two DSI Tx, one eDP/DP and one
DPI interface.
* Integrated gigabit ethernet switch, up to 8 ports (TDA4VH), two ports
support 10Gb USXGMII; Two 4 lane PCIe-GEN3 controllers, USB3.0 Dual-role
device subsystems, Up to 20 MCANs, among other peripherals.
See J784S4 Technical Reference Manual (SPRUJ52 - JUNE 2022)
for further details: http://www.ti.com/lit/zip/spruj52
In addtion, the J784S4 EVM board is designed for TI J784S4 SoC. It
supports the following interfaces:
* 32 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 Input Audio Jack, x1 Output Audio Jack
* x1 USB2.0 Hub with two Type A host and x1 USB 3.1 Type-C Port
* x2 4L PCIe connector
* x1 UHS-1 capable micro-SD card slot
* 512 Mbit OSPI flash, 1 Gbit Octal NAND flash, 512 Mbit QSPI flash,
UFS flash.
* x6 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* x2 ENET Expansion Connector, x1 GESI expander, x2 Display connector
* x1 15-pin CSI header
* x6 MCAN instances
Udit Kumar [Wed, 21 Feb 2024 14:23:44 +0000 (19:53 +0530)]
dma: ti: k3-udma: Fix ring_idx to pair k3 nav rings
ring_idx was not correctly assigned in case of tflow_id is zero.
Which leads to wrong pairing of DMA for drivers like OSPI.
Fixes: 4312a1dfca26 ("dma: ti: k3-udma: Use ring_idx to pair k3 nav rings") Reviewed-by: Jai Luthra <j-luthra@ti.com> Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Dasnavis Sabiya [Fri, 23 Feb 2024 20:21:52 +0000 (01:51 +0530)]
configs: am69_sk: Add defconfig for AM69 SK board
Add defconfig for AM69 SK A72 and R5 configuration.
This inlcudes and modifies the J784S4 EVM defconfigs:
j784s4_evm_a72_defconfig -> am69_sk_a72_defconfig
j784s4_evm_r5_defconfig -> am69_sk_r5_defconfig
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com> Signed-off-by: Apurva Nandan <a-nandan@ti.com> Reviewed-by: Andrew Davis <afd@ti.com> Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK
dma: ti: k3-udma: Fix error handling for setup_resources() in udma_probe()
In udma_probe() the return value of setup_resources() is stored in the
u32 "ch_count" member of "struct udma_dev", due to which any negative
return value which indicates an error is masked.
Fix this by storing the return value of setup_resources() in the already
declared integer variable "ret", followed by assigning it to the "ch_count"
member of "struct udma_dev" in case of no error.
While at it, change the "return ret" at the end of udma_probe() to a
"return 0", to explicitly indicate that probe was successful.
Fixes: a8837cf43839 ("dma: ti: k3-udma: Query DMA channels allocated from Resource Manager") Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
arm: mach-k3: am62: Fixup thermal zone critical points
Read the max temperature for the SoC temperature grade from the hardware
and change the critical trip nodes on each thermal zone of FDT at
runtime so they are correct with the hardware value for its grade.
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
projects / thirdparty / u-boot.git / log
