[people/ms/u-boot.git] / include / configs / P1023RDB.h

/*
 * Copyright 2013 Freescale Semiconductor, Inc.
 *
 * Authors:  Roy Zang <tie-fei.zang@freescale.com>
 *	     Chunhe Lan <Chunhe.Lan@freescale.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#define CONFIG_DISPLAY_BOARDINFO

#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE	0xeff40000
#endif

#ifndef CONFIG_SYS_MONITOR_BASE
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
#endif

#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
#endif

/* High Level Configuration Options */
#define CONFIG_BOOKE		/* BOOKE */
#define CONFIG_E500		/* BOOKE e500 family */
#define CONFIG_P1023
#define CONFIG_MP		/* support multiple processors */

#define CONFIG_FSL_ELBC		/* Has Enhanced localbus controller */
#define CONFIG_PCI		/* Enable PCI/PCIE */
#define CONFIG_PCI_INDIRECT_BRIDGE     /* indirect PCI bridge support */
#define CONFIG_PCIE1		/* PCIE controler 1 (slot 1) */
#define CONFIG_PCIE2		/* PCIE controler 2 (slot 2) */
#define CONFIG_PCIE3		/* PCIE controler 3 (slot 3) */
#define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
#define CONFIG_FSL_PCIE_RESET	/* need PCIe reset errata */
#define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
#define CONFIG_FSL_LAW		/* Use common FSL init code */

#ifndef __ASSEMBLY__
extern unsigned long get_clock_freq(void);
#endif

#define CONFIG_SYS_CLK_FREQ	66666666
#define CONFIG_DDR_CLK_FREQ	CONFIG_SYS_CLK_FREQ

/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_L2_CACHE			/* toggle L2 cache */
#define CONFIG_BTB			/* toggle branch predition */
#define CONFIG_HWCONFIG

#define CONFIG_ENABLE_36BIT_PHYS

#define CONFIG_SYS_MEMTEST_START	0x01000000	/* memtest works on */
#define CONFIG_SYS_MEMTEST_END		0x02000000

#define CONFIG_PANIC_HANG	/* do not reset board on panic */

/* Implement conversion of addresses in the LBC */
#define CONFIG_SYS_LBC_LBCR		0x00000000
#define CONFIG_SYS_LBC_LCRR		LCRR_CLKDIV_8

/* DDR Setup */
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE

#define CONFIG_DIMM_SLOTS_PER_CTLR	1
#define CONFIG_CHIP_SELECTS_PER_CTRL	1

#define CONFIG_DDR_SPD
#define CONFIG_SYS_FSL_DDR3
#define CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_SDRAM_SIZE		512u	/* DDR is 512M */
#define CONFIG_SYS_SPD_BUS_NUM          0
#define SPD_EEPROM_ADDRESS              0x50
#define CONFIG_SYS_DDR_RAW_TIMING

/*
 * Memory map
 *
 * 0x0000_0000	0x1fff_ffff	DDR			512M cacheable
 * 0x8000_0000	0xbfff_ffff	PCI Express Mem		1G non-cacheable
 * 0xc000_0000	0xdfff_ffff	PCI			512M non-cacheable
 * 0xe100_0000	0xe3ff_ffff	PCI IO range		4M non-cacheable
 * 0xff00_0000	0xff3f_ffff	DPAA_QBMAN		4M cacheable
 * 0xff60_0000	0xff7f_ffff	CCSR			2M non-cacheable
 * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K cacheable TLB0
 *
 * Localbus non-cacheable
 *
 * 0xec00_0000	0xefff_ffff	NOR flash		64M non-cacheable
 * 0xffa0_0000	0xffaf_ffff	NAND			1M non-cacheable
 */

/*
 * Local Bus Definitions
 */
#define CONFIG_SYS_FLASH_BASE		0xec000000 /* start of FLASH 64M */
#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE

#define CONFIG_FLASH_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
				| BR_PS_16 | BR_V)
#define CONFIG_FLASH_OR_PRELIM	0xfc000ff7

#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT	512	/* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

#define CONFIG_BOARD_EARLY_INIT_F	/* call board_early_init_f function */
#define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */

#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000/* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
					GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_LEN	(768 * 1024)	  /* Reserve 512 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN	(6 * 1024 * 1024) /* Reserved for malloc */

#define CONFIG_SYS_NAND_BASE		0xffa00000
#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE

#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_CMD_NAND
#define CONFIG_NAND_FSL_ELBC
#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)

/* NAND flash config */
#define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
				| BR_PS_8		/* Port Size = 8bit */ \
				| BR_MS_FCM		/* MSEL = FCM */ \
				| BR_V)			/* valid */
#define CONFIG_SYS_NAND_OR_PRELIM  (OR_AM_256KB		/* length 256K */ \
				| OR_FCM_PGS \
				| OR_FCM_CSCT \
				| OR_FCM_CST \
				| OR_FCM_CHT \
				| OR_FCM_SCY_1 \
				| OR_FCM_TRLX \
				| OR_FCM_EHTR)

#define CONFIG_SYS_BR0_PRELIM	CONFIG_FLASH_BR_PRELIM	/* NOR Base Address */
#define CONFIG_SYS_OR0_PRELIM	CONFIG_FLASH_OR_PRELIM	/* NOR Options */
#define CONFIG_SYS_BR1_PRELIM	CONFIG_SYS_NAND_BR_PRELIM
#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */

/* Serial Port */
#define CONFIG_CONS_INDEX		1
#undef	CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

#define CONFIG_SYS_BAUDRATE_TABLE	\
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR + 0x4500)
#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR + 0x4600)

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED	400000
#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
#define CONFIG_SYS_FSL_I2C2_SPEED	400000
#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100

/*
 * I2C2 EEPROM
 */
#define CONFIG_ID_EEPROM
#ifdef CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#endif
#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
#define CONFIG_SYS_EEPROM_BUS_NUM		0

#define CONFIG_CMD_I2C

/*
 * General PCI
 * Memory space is mapped 1-1, but I/O space must start from 0.
 */

/* controller 3, Slot 1, tgtid 3, Base address b000 */
#define CONFIG_SYS_PCIE3_NAME		"Slot 3"
#define CONFIG_SYS_PCIE3_MEM_VIRT	0x80000000
#define CONFIG_SYS_PCIE3_MEM_BUS	0x80000000
#define CONFIG_SYS_PCIE3_MEM_PHYS	0x80000000
#define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
#define CONFIG_SYS_PCIE3_IO_VIRT	0xffc00000
#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
#define CONFIG_SYS_PCIE3_IO_PHYS	0xffc00000
#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */

/* controller 2, direct to uli, tgtid 2, Base address 9000 */
#define CONFIG_SYS_PCIE2_NAME		"Slot 2"
#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
#define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
#define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
#define CONFIG_SYS_PCIE2_IO_PHYS	0xffc10000
#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */

/* controller 1, Slot 2, tgtid 1, Base address a000 */
#define CONFIG_SYS_PCIE1_NAME		"Slot 1"
#define CONFIG_SYS_PCIE1_MEM_VIRT	0xc0000000
#define CONFIG_SYS_PCIE1_MEM_BUS	0xc0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc0000000
#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc20000
#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS	0xffc20000
#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */

#if defined(CONFIG_PCI)
#define CONFIG_PCI_PNP		/* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
#endif	/* CONFIG_PCI */

/*
 * Environment
 */
#define CONFIG_ENV_OVERWRITE

#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE		0x2000
#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */

#define CONFIG_LOADS_ECHO		/* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */

/*
 * Command line configuration.
 */
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_PING
#define CONFIG_CMD_MII
#define CONFIG_CMD_REGINFO

#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif

/*
 * USB
 */
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
#define CONFIG_USB_EHCI

#ifdef CONFIG_USB_EHCI
#define CONFIG_CMD_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#define CONFIG_USB_STORAGE
#define CONFIG_CMD_FAT
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#endif
#endif

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
#endif
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 64 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)   /* Initial Memory map for Linux*/
#define CONFIG_SYS_BOOTM_LEN	(64 << 20)   /* Increase max gunzip size */

/*
 * Environment Configuration
 */
#define CONFIG_BOOTFILE		"uImage"
#define CONFIG_UBOOTPATH	(u-boot.bin) /* U-Boot image on TFTP server */

/* default location for tftp and bootm */
#define CONFIG_LOADADDR		1000000

#define CONFIG_BOOTDELAY -1	/* -1 disables auto-boot */

#define CONFIG_BAUDRATE	115200

/* Qman/Bman */
#define CONFIG_SYS_DPAA_QBMAN		/* support Q/Bman */
#define CONFIG_SYS_QMAN_MEM_BASE	0xff000000
#define CONFIG_SYS_QMAN_MEM_PHYS	CONFIG_SYS_QMAN_MEM_BASE
#define CONFIG_SYS_QMAN_MEM_SIZE	0x00200000
#define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
#define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
#define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
#define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
					CONFIG_SYS_QMAN_CENA_SIZE)
#define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_SWP_ISDR_REG	0xE08
#define CONFIG_SYS_BMAN_MEM_BASE	0xff200000
#define CONFIG_SYS_BMAN_MEM_PHYS	CONFIG_SYS_BMAN_MEM_BASE
#define CONFIG_SYS_BMAN_MEM_SIZE	0x00200000
#define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
#define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
#define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
#define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
					CONFIG_SYS_BMAN_CENA_SIZE)
#define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_SWP_ISDR_REG	0xE08

/* For FM */
#define CONFIG_SYS_DPAA_FMAN
#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */

#ifdef CONFIG_SYS_DPAA_FMAN
#define CONFIG_FMAN_ENET
#define CONFIG_PHY_ATHEROS
#endif

/* Default address of microcode for the Linux Fman driver */
/* QE microcode/firmware address */
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
#define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

#ifdef CONFIG_FMAN_ENET
#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR	0x1
#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR	0x2

#define CONFIG_SYS_TBIPA_VALUE	8
#define CONFIG_MII		/* MII PHY management */
#define CONFIG_ETHPRIME		"FM1@DTSEC1"
#endif

#define CONFIG_EXTRA_ENV_SETTINGS	\
	"netdev=eth0\0"						\
	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
	"loadaddr=1000000\0"					\
	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
	"tftpflash=tftpboot $loadaddr $uboot; "			\
		"protect off $ubootaddr +$filesize; "		\
		"erase $ubootaddr +$filesize; "			\
		"cp.b $loadaddr $ubootaddr $filesize; "		\
		"protect on $ubootaddr +$filesize; "		\
		"cmp.b $loadaddr $ubootaddr $filesize\0"	\
	"consoledev=ttyS0\0"					\
	"ramdiskaddr=2000000\0"					\
	"ramdiskfile=rootfs.ext2.gz.uboot\0"			\
	"fdtaddr=c00000\0"					\
	"fdtfile=p1023rdb.dtb\0"				\
	"othbootargs=ramdisk_size=600000\0"			\
	"bdev=sda1\0"						\
	"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"

#define CONFIG_HDBOOT					\
	"setenv bootargs root=/dev/$bdev rw "		\
	"console=$consoledev,$baudrate $othbootargs;"	\
	"tftp $loadaddr $bootfile;"			\
	"tftp $fdtaddr $fdtfile;"			\
	"bootm $loadaddr - $fdtaddr"

#define CONFIG_NFSBOOTCOMMAND						\
	"setenv bootargs root=/dev/nfs rw "				\
	"nfsroot=$serverip:$rootpath "					\
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs;"			\
	"tftp $loadaddr $bootfile;"					\
	"tftp $fdtaddr $fdtfile;"					\
	"bootm $loadaddr - $fdtaddr"

#define CONFIG_RAMBOOTCOMMAND						\
	"setenv bootargs root=/dev/ram rw "				\
	"console=$consoledev,$baudrate $othbootargs;"			\
	"tftp $ramdiskaddr $ramdiskfile;"				\
	"tftp $loadaddr $bootfile;"					\
	"tftp $fdtaddr $fdtfile;"					\
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_BOOTCOMMAND		CONFIG_RAMBOOTCOMMAND

#endif	/* __CONFIG_H */
Commit	Line	Data
57072338 CL	1	/*
	2	* Copyright 2013 Freescale Semiconductor, Inc.
	3	*
	4	* Authors: Roy Zang <tie-fei.zang@freescale.com>
	5	* Chunhe Lan <Chunhe.Lan@freescale.com>
	6	*
1a459660	7	* SPDX-License-Identifier: GPL-2.0+
57072338 CL	8	*/
	9
	10	#ifndef __CONFIG_H
	11	#define __CONFIG_H
	12
fb735723 CL	13	#define CONFIG_DISPLAY_BOARDINFO
fb735723 CL	14
57072338	15	#ifndef CONFIG_SYS_TEXT_BASE
e222b1f3	16	#define CONFIG_SYS_TEXT_BASE 0xeff40000
57072338 CL	17	#endif
	18
	19	#ifndef CONFIG_SYS_MONITOR_BASE
	20	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
	21	#endif
	22
	23	#ifndef CONFIG_RESET_VECTOR_ADDRESS
	24	#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
	25	#endif
	26
	27	/* High Level Configuration Options */
	28	#define CONFIG_BOOKE /* BOOKE */
	29	#define CONFIG_E500 /* BOOKE e500 family */
57072338 CL	30	#define CONFIG_P1023
	31	#define CONFIG_MP /* support multiple processors */
	32
	33	#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
	34	#define CONFIG_PCI /* Enable PCI/PCIE */
	35	#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
	36	#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
	37	#define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */
	38	#define CONFIG_PCIE3 /* PCIE controler 3 (slot 3) */
	39	#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
	40	#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
	41	#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
	42	#define CONFIG_FSL_LAW /* Use common FSL init code */
	43
	44	#ifndef __ASSEMBLY__
	45	extern unsigned long get_clock_freq(void);
	46	#endif
	47
	48	#define CONFIG_SYS_CLK_FREQ 66666666
	49	#define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ
	50
	51	/*
	52	* These can be toggled for performance analysis, otherwise use default.
	53	*/
	54	#define CONFIG_L2_CACHE /* toggle L2 cache */
	55	#define CONFIG_BTB /* toggle branch predition */
	56	#define CONFIG_HWCONFIG
	57
	58	#define CONFIG_ENABLE_36BIT_PHYS
	59
	60	#define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */
	61	#define CONFIG_SYS_MEMTEST_END 0x02000000
	62
	63	#define CONFIG_PANIC_HANG /* do not reset board on panic */
	64
	65	/* Implement conversion of addresses in the LBC */
	66	#define CONFIG_SYS_LBC_LBCR 0x00000000
	67	#define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8
	68
	69	/* DDR Setup */
	70	#define CONFIG_VERY_BIG_RAM
	71	#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
	72	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
	73
	74	#define CONFIG_DIMM_SLOTS_PER_CTLR 1
	75	#define CONFIG_CHIP_SELECTS_PER_CTRL 1
	76
	77	#define CONFIG_DDR_SPD
5614e71b	78	#define CONFIG_SYS_FSL_DDR3
57072338 CL	79	#define CONFIG_FSL_DDR_INTERACTIVE
	80	#define CONFIG_SYS_SDRAM_SIZE 512u /* DDR is 512M */
	81	#define CONFIG_SYS_SPD_BUS_NUM 0
	82	#define SPD_EEPROM_ADDRESS 0x50
	83	#define CONFIG_SYS_DDR_RAW_TIMING
	84
	85	/*
	86	* Memory map
	87	*
	88	* 0x0000_0000 0x1fff_ffff DDR 512M cacheable
	89	* 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
	90	* 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
	91	* 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
	92	* 0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M cacheable
	93	* 0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable
	94	* 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable TLB0
	95	*
	96	* Localbus non-cacheable
	97	*
	98	* 0xec00_0000 0xefff_ffff NOR flash 64M non-cacheable
	99	* 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable
	100	*/
	101
	102	/*
	103	* Local Bus Definitions
	104	*/
	105	#define CONFIG_SYS_FLASH_BASE 0xec000000 /* start of FLASH 64M */
	106	#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
	107
	108	#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
	109	\| BR_PS_16 \| BR_V)
	110	#define CONFIG_FLASH_OR_PRELIM 0xfc000ff7
	111
	112	#define CONFIG_FLASH_CFI_DRIVER
	113	#define CONFIG_SYS_FLASH_CFI
	114	#define CONFIG_SYS_FLASH_EMPTY_INFO
	115	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	116	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
	117	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	118	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
	119
	120	#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f function */
	121	#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
	122
	123	#define CONFIG_SYS_INIT_RAM_LOCK
	124	#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
	125	#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* Size of used area in RAM */
	126	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
	127	GENERATED_GBL_DATA_SIZE)
	128	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
	129
9307cbab	130	#define CONFIG_SYS_MONITOR_LEN (768 * 1024) /* Reserve 512 kB for Mon */
57072338 CL	131	#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */
	132
	133	#define CONFIG_SYS_NAND_BASE 0xffa00000
	134	#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
	135
	136	#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
	137	#define CONFIG_SYS_MAX_NAND_DEVICE 1
57072338 CL	138	#define CONFIG_CMD_NAND
	139	#define CONFIG_NAND_FSL_ELBC
	140	#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
	141
	142	/* NAND flash config */
	143	#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
	144	\| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
	145	\| BR_PS_8 /* Port Size = 8bit */ \
	146	\| BR_MS_FCM /* MSEL = FCM */ \
	147	\| BR_V) /* valid */
	148	#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \
	149	\| OR_FCM_PGS \
	150	\| OR_FCM_CSCT \
	151	\| OR_FCM_CST \
	152	\| OR_FCM_CHT \
	153	\| OR_FCM_SCY_1 \
	154	\| OR_FCM_TRLX \
	155	\| OR_FCM_EHTR)
	156
	157	#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
	158	#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
	159	#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
	160	#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
	161
	162	/* Serial Port */
	163	#define CONFIG_CONS_INDEX 1
	164	#undef CONFIG_SERIAL_SOFTWARE_FIFO
57072338 CL	165	#define CONFIG_SYS_NS16550_SERIAL
	166	#define CONFIG_SYS_NS16550_REG_SIZE 1
	167	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
	168
	169	#define CONFIG_SYS_BAUDRATE_TABLE \
	170	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
	171
	172	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
	173	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
	174
57072338	175	/* I2C */
00f792e0 HS	176	#define CONFIG_SYS_I2C
	177	#define CONFIG_SYS_I2C_FSL
	178	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	179	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	180	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	181	#define CONFIG_SYS_FSL_I2C2_SPEED 400000
	182	#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
	183	#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
57072338 CL	184
	185	/*
	186	* I2C2 EEPROM
	187	*/
	188	#define CONFIG_ID_EEPROM
	189	#ifdef CONFIG_ID_EEPROM
	190	#define CONFIG_SYS_I2C_EEPROM_NXID
	191	#endif
	192	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
	193	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	194	#define CONFIG_SYS_EEPROM_BUS_NUM 0
	195
	196	#define CONFIG_CMD_I2C
	197
	198	/*
	199	* General PCI
	200	* Memory space is mapped 1-1, but I/O space must start from 0.
	201	*/
	202
	203	/* controller 3, Slot 1, tgtid 3, Base address b000 */
	204	#define CONFIG_SYS_PCIE3_NAME "Slot 3"
	205	#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
	206	#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
	207	#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
	208	#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
	209	#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
	210	#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
	211	#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000
	212	#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
	213
	214	/* controller 2, direct to uli, tgtid 2, Base address 9000 */
	215	#define CONFIG_SYS_PCIE2_NAME "Slot 2"
	216	#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
	217	#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
	218	#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
	219	#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
	220	#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
	221	#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
	222	#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
	223	#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
	224
	225	/* controller 1, Slot 2, tgtid 1, Base address a000 */
	226	#define CONFIG_SYS_PCIE1_NAME "Slot 1"
	227	#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
	228	#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
	229	#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
	230	#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
	231	#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
	232	#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
	233	#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000
	234	#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
	235
	236	#if defined(CONFIG_PCI)
57072338 CL	237	#define CONFIG_PCI_PNP /* do pci plug-and-play */
	238	#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
	239	#endif /* CONFIG_PCI */
	240
	241	/*
	242	* Environment
	243	*/
	244	#define CONFIG_ENV_OVERWRITE
	245
	246	#define CONFIG_ENV_IS_IN_FLASH
57072338	247	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
57072338 CL	248	#define CONFIG_ENV_SIZE 0x2000
	249	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
	250
	251	#define CONFIG_LOADS_ECHO /* echo on for serial download */
	252	#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
	253
	254	/*
	255	* Command line configuration.
	256	*/
57072338 CL	257	#define CONFIG_CMD_IRQ
	258	#define CONFIG_CMD_PING
	259	#define CONFIG_CMD_MII
57072338 CL	260	#define CONFIG_CMD_REGINFO
	261
	262	#if defined(CONFIG_PCI)
	263	#define CONFIG_CMD_PCI
57072338 CL	264	#endif
	265
	266	/*
	267	* USB
	268	*/
	269	#define CONFIG_HAS_FSL_DR_USB
	270	#ifdef CONFIG_HAS_FSL_DR_USB
	271	#define CONFIG_USB_EHCI
	272
	273	#ifdef CONFIG_USB_EHCI
	274	#define CONFIG_CMD_USB
	275	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
	276	#define CONFIG_USB_EHCI_FSL
	277	#define CONFIG_USB_STORAGE
	278	#define CONFIG_CMD_FAT
	279	#define CONFIG_CMD_EXT2
	280	#define CONFIG_CMD_FAT
	281	#define CONFIG_DOS_PARTITION
	282	#endif
	283	#endif
	284
	285	/*
	286	* Miscellaneous configurable options
	287	*/
	288	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	289	#define CONFIG_CMDLINE_EDITING /* Command-line editing */
	290	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
57072338 CL	291	#if defined(CONFIG_CMD_KGDB)
	292	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	293	#else
	294	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	295	#endif
	296	/* Print Buffer Size */
	297	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
	298	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	299	/* Boot Argument Buffer Size */
	300	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
57072338 CL	301
	302	/*
	303	* For booting Linux, the board info and command line data
	304	* have to be in the first 64 MB of memory, since this is
	305	* the maximum mapped by the Linux kernel during initialization.
	306	*/
	307	#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
	308	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
	309
	310	/*
	311	* Environment Configuration
	312	*/
	313	#define CONFIG_BOOTFILE "uImage"
	314	#define CONFIG_UBOOTPATH (u-boot.bin) /* U-Boot image on TFTP server */
	315
	316	/* default location for tftp and bootm */
	317	#define CONFIG_LOADADDR 1000000
	318
	319	#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
	320
	321	#define CONFIG_BAUDRATE 115200
	322
	323	/* Qman/Bman */
	324	#define CONFIG_SYS_DPAA_QBMAN /* support Q/Bman */
	325	#define CONFIG_SYS_QMAN_MEM_BASE 0xff000000
	326	#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
	327	#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
3fa66db4 JL	328	#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
	329	#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
	330	#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
	331	#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
	332	#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
	333	CONFIG_SYS_QMAN_CENA_SIZE)
	334	#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
	335	#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
57072338 CL	336	#define CONFIG_SYS_BMAN_MEM_BASE 0xff200000
	337	#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
	338	#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
3fa66db4 JL	339	#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
	340	#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
	341	#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
	342	#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
	343	#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
	344	CONFIG_SYS_BMAN_CENA_SIZE)
	345	#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
	346	#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
57072338 CL	347
	348	/* For FM */
	349	#define CONFIG_SYS_DPAA_FMAN
	350	#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
	351
	352	#ifdef CONFIG_SYS_DPAA_FMAN
	353	#define CONFIG_FMAN_ENET
	354	#define CONFIG_PHY_ATHEROS
	355	#endif
	356
	357	/* Default address of microcode for the Linux Fman driver */
	358	/* QE microcode/firmware address */
	359	#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
dcf1d774	360	#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
57072338 CL	361	#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
	362	#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
	363
	364	#ifdef CONFIG_FMAN_ENET
	365	#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x1
	366	#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x2
	367
	368	#define CONFIG_SYS_TBIPA_VALUE 8
	369	#define CONFIG_MII /* MII PHY management */
	370	#define CONFIG_ETHPRIME "FM1@DTSEC1"
	371	#endif
	372
	373	#define CONFIG_EXTRA_ENV_SETTINGS \
5eabbae0 CL	374	"netdev=eth0\0" \
	375	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
	376	"loadaddr=1000000\0" \
	377	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
	378	"tftpflash=tftpboot $loadaddr $uboot; " \
	379	"protect off $ubootaddr +$filesize; " \
	380	"erase $ubootaddr +$filesize; " \
	381	"cp.b $loadaddr $ubootaddr $filesize; " \
	382	"protect on $ubootaddr +$filesize; " \
	383	"cmp.b $loadaddr $ubootaddr $filesize\0" \
	384	"consoledev=ttyS0\0" \
	385	"ramdiskaddr=2000000\0" \
	386	"ramdiskfile=rootfs.ext2.gz.uboot\0" \
	387	"fdtaddr=c00000\0" \
	388	"fdtfile=p1023rdb.dtb\0" \
	389	"othbootargs=ramdisk_size=600000\0" \
	390	"bdev=sda1\0" \
57072338 CL	391	"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
57072338 CL	392
5eabbae0 CL	393	#define CONFIG_HDBOOT \
	394	"setenv bootargs root=/dev/$bdev rw " \
	395	"console=$consoledev,$baudrate $othbootargs;" \
	396	"tftp $loadaddr $bootfile;" \
	397	"tftp $fdtaddr $fdtfile;" \
	398	"bootm $loadaddr - $fdtaddr"
	399
	400	#define CONFIG_NFSBOOTCOMMAND \
	401	"setenv bootargs root=/dev/nfs rw " \
	402	"nfsroot=$serverip:$rootpath " \
	403	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	404	"console=$consoledev,$baudrate $othbootargs;" \
	405	"tftp $loadaddr $bootfile;" \
	406	"tftp $fdtaddr $fdtfile;" \
	407	"bootm $loadaddr - $fdtaddr"
	408
	409	#define CONFIG_RAMBOOTCOMMAND \
	410	"setenv bootargs root=/dev/ram rw " \
	411	"console=$consoledev,$baudrate $othbootargs;" \
	412	"tftp $ramdiskaddr $ramdiskfile;" \
	413	"tftp $loadaddr $bootfile;" \
	414	"tftp $fdtaddr $fdtfile;" \
	415	"bootm $loadaddr $ramdiskaddr $fdtaddr"
	416
	417	#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
	418
57072338	419	#endif /* __CONFIG_H */