include/configs/nitrogen6x.h

   1 /*
   2  * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
   3  *
   4  * Configuration settings for the Boundary Devices Nitrogen6X
   5  * and Freescale i.MX6Q Sabre Lite boards.
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 #define CONFIG_MX6
  14 #define CONFIG_DISPLAY_CPUINFO
  15 #define CONFIG_DISPLAY_BOARDINFO
  16
  17 #define CONFIG_MACH_TYPE        3769
  18
  19 #include <asm/arch/imx-regs.h>
  20 #include <asm/imx-common/gpio.h>
  21
  22 #define CONFIG_CMDLINE_TAG
  23 #define CONFIG_SETUP_MEMORY_TAGS
  24 #define CONFIG_INITRD_TAG
  25 #define CONFIG_REVISION_TAG
  26
  27 /* Size of malloc() pool */
  28 #define CONFIG_SYS_MALLOC_LEN           (10 * 1024 * 1024)
  29
  30 #define CONFIG_BOARD_EARLY_INIT_F
  31 #define CONFIG_MISC_INIT_R
  32 #define CONFIG_MXC_GPIO
  33 #define CONFIG_MV_UDC
  34 #define CONFIG_USBD_HS
  35 #define CONFIG_USB_GADGET_DUALSPEED
  36 #define CONFIG_USB_ETHER
  37 #define CONFIG_USB_ETH_CDC
  38 #define CONFIG_NETCONSOLE
  39
  40 #define CONFIG_CMD_FUSE
  41 #ifdef CONFIG_CMD_FUSE
  42 #define CONFIG_MXC_OCOTP
  43 #endif
  44
  45 #define CONFIG_MXC_UART
  46 #define CONFIG_MXC_UART_BASE           UART2_BASE
  47
  48 #define CONFIG_CMD_SF
  49 #ifdef CONFIG_CMD_SF
  50 #define CONFIG_SPI_FLASH
  51 #define CONFIG_SPI_FLASH_SST
  52 #define CONFIG_MXC_SPI
  53 #define CONFIG_SF_DEFAULT_BUS  0
  54 #define CONFIG_SF_DEFAULT_CS   (0|(IMX_GPIO_NR(3, 19)<<8))
  55 #define CONFIG_SF_DEFAULT_SPEED 25000000
  56 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
  57 #endif
  58
  59 /* I2C Configs */
  60 #define CONFIG_CMD_I2C
  61 #define CONFIG_SYS_I2C
  62 #define CONFIG_SYS_I2C_MXC
  63 #define CONFIG_SYS_I2C_SPEED            100000
  64
  65 /* OCOTP Configs */
  66 #define CONFIG_CMD_IMXOTP
  67 #ifdef CONFIG_CMD_IMXOTP
  68 #define CONFIG_IMX_OTP
  69 #define IMX_OTP_BASE                    OCOTP_BASE_ADDR
  70 #define IMX_OTP_ADDR_MAX                0x7F
  71 #define IMX_OTP_DATA_ERROR_VAL          0xBADABADA
  72 #define IMX_OTPWRITE_ENABLED
  73 #endif
  74
  75 /* MMC Configs */
  76 #define CONFIG_FSL_ESDHC
  77 #define CONFIG_FSL_USDHC
  78 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
  79 #define CONFIG_SYS_FSL_USDHC_NUM       2
  80
  81 #define CONFIG_MMC
  82 #define CONFIG_CMD_MMC
  83 #define CONFIG_GENERIC_MMC
  84 #define CONFIG_BOUNCE_BUFFER
  85 #define CONFIG_CMD_EXT2
  86 #define CONFIG_CMD_FAT
  87 #define CONFIG_DOS_PARTITION
  88
  89 #ifdef CONFIG_MX6Q
  90 #define CONFIG_CMD_SATA
  91 #endif
  92
  93 /*
  94  * SATA Configs
  95  */
  96 #ifdef CONFIG_CMD_SATA
  97 #define CONFIG_DWC_AHSATA
  98 #define CONFIG_SYS_SATA_MAX_DEVICE      1
  99 #define CONFIG_DWC_AHSATA_PORT_ID       0
 100 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
 101 #define CONFIG_LBA48
 102 #define CONFIG_LIBATA
 103 #endif
 104
 105 #define CONFIG_CMD_PING
 106 #define CONFIG_CMD_DHCP
 107 #define CONFIG_CMD_MII
 108 #define CONFIG_CMD_NET
 109 #define CONFIG_FEC_MXC
 110 #define CONFIG_MII
 111 #define IMX_FEC_BASE                    ENET_BASE_ADDR
 112 #define CONFIG_FEC_XCV_TYPE             RGMII
 113 #define CONFIG_ETHPRIME                 "FEC"
 114 #define CONFIG_FEC_MXC_PHYADDR          6
 115 #define CONFIG_PHYLIB
 116 #define CONFIG_PHY_MICREL
 117 #define CONFIG_PHY_MICREL_KSZ9021
 118
 119 /* USB Configs */
 120 #define CONFIG_CMD_USB
 121 #define CONFIG_CMD_FAT
 122 #define CONFIG_USB_EHCI
 123 #define CONFIG_USB_EHCI_MX6
 124 #define CONFIG_USB_STORAGE
 125 #define CONFIG_USB_HOST_ETHER
 126 #define CONFIG_USB_ETHER_ASIX
 127 #define CONFIG_USB_ETHER_SMSC95XX
 128 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 129 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET        /* For OTG port */
 130 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
 131 #define CONFIG_MXC_USB_FLAGS    0
 132
 133 /* Miscellaneous commands */
 134 #define CONFIG_CMD_BMODE
 135 #define CONFIG_CMD_SETEXPR
 136
 137 /* Framebuffer and LCD */
 138 #define CONFIG_VIDEO
 139 #define CONFIG_VIDEO_IPUV3
 140 #define CONFIG_CFB_CONSOLE
 141 #define CONFIG_VGA_AS_SINGLE_DEVICE
 142 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 143 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
 144 #define CONFIG_VIDEO_BMP_RLE8
 145 #define CONFIG_SPLASH_SCREEN
 146 #define CONFIG_BMP_16BPP
 147 #define CONFIG_VIDEO_LOGO
 148 #define CONFIG_IPUV3_CLK 260000000
 149 #define CONFIG_CMD_HDMIDETECT
 150 #define CONFIG_CONSOLE_MUX
 151 #define CONFIG_IMX_HDMI
 152
 153 /* allow to overwrite serial and ethaddr */
 154 #define CONFIG_ENV_OVERWRITE
 155 #define CONFIG_CONS_INDEX              1
 156 #define CONFIG_BAUDRATE                        115200
 157
 158 /* Command definition */
 159 #include <config_cmd_default.h>
 160
 161 #undef CONFIG_CMD_IMLS
 162
 163 #define CONFIG_BOOTDELAY               1
 164
 165 #define CONFIG_PREBOOT                 ""
 166
 167 #define CONFIG_LOADADDR                        0x12000000
 168 #define CONFIG_SYS_TEXT_BASE           0x17800000
 169
 170 #ifdef CONFIG_CMD_SATA
 171 #define CONFIG_DRIVE_SATA "sata "
 172 #else
 173 #define CONFIG_DRIVE_SATA
 174 #endif
 175
 176 #ifdef CONFIG_CMD_MMC
 177 #define CONFIG_DRIVE_MMC "mmc "
 178 #else
 179 #define CONFIG_DRIVE_MMC
 180 #endif
 181
 182 #define CONFIG_DRIVE_TYPES CONFIG_DRIVE_SATA CONFIG_DRIVE_MMC
 183
 184 #if defined(CONFIG_SABRELITE)
 185 #define CONFIG_EXTRA_ENV_SETTINGS \
 186         "script=boot.scr\0" \
 187         "uimage=uImage\0" \
 188         "console=ttymxc1\0" \
 189         "fdt_high=0xffffffff\0" \
 190         "initrd_high=0xffffffff\0" \
 191         "fdt_file=imx6q-sabrelite.dtb\0" \
 192         "fdt_addr=0x11000000\0" \
 193         "boot_fdt=try\0" \
 194         "ip_dyn=yes\0" \
 195         "mmcdev=0\0" \
 196         "mmcpart=1\0" \
 197         "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
 198         "mmcargs=setenv bootargs console=${console},${baudrate} " \
 199                 "root=${mmcroot}\0" \
 200         "loadbootscript=" \
 201                 "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 202         "bootscript=echo Running bootscript from mmc ...; " \
 203                 "source\0" \
 204         "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
 205         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 206         "mmcboot=echo Booting from mmc ...; " \
 207                 "run mmcargs; " \
 208                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 209                         "if run loadfdt; then " \
 210                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 211                         "else " \
 212                                 "if test ${boot_fdt} = try; then " \
 213                                         "bootm; " \
 214                                 "else " \
 215                                         "echo WARN: Cannot load the DT; " \
 216                                 "fi; " \
 217                         "fi; " \
 218                 "else " \
 219                         "bootm; " \
 220                 "fi;\0" \
 221         "netargs=setenv bootargs console=${console},${baudrate} " \
 222                 "root=/dev/nfs " \
 223         "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 224                 "netboot=echo Booting from net ...; " \
 225                 "run netargs; " \
 226                 "if test ${ip_dyn} = yes; then " \
 227                         "setenv get_cmd dhcp; " \
 228                 "else " \
 229                         "setenv get_cmd tftp; " \
 230                 "fi; " \
 231                 "${get_cmd} ${uimage}; " \
 232                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 233                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 234                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 235                         "else " \
 236                                 "if test ${boot_fdt} = try; then " \
 237                                         "bootm; " \
 238                                 "else " \
 239                                         "echo WARN: Cannot load the DT; " \
 240                                 "fi; " \
 241                         "fi; " \
 242                 "else " \
 243                         "bootm; " \
 244                 "fi;\0"
 245
 246 #define CONFIG_BOOTCOMMAND \
 247            "mmc dev ${mmcdev}; if mmc rescan; then " \
 248                    "if run loadbootscript; then " \
 249                            "run bootscript; " \
 250                    "else " \
 251                            "if run loaduimage; then " \
 252                                    "run mmcboot; " \
 253                            "else run netboot; " \
 254                            "fi; " \
 255                    "fi; " \
 256            "else run netboot; fi"
 257 #else
 258 #define CONFIG_EXTRA_ENV_SETTINGS \
 259         "console=ttymxc1\0" \
 260         "clearenv=if sf probe || sf probe || sf probe 1 ; then " \
 261                 "sf erase 0xc0000 0x2000 && " \
 262                 "echo restored environment to factory default ; fi\0" \
 263         "bootcmd=for dtype in " CONFIG_DRIVE_TYPES \
 264                 "; do " \
 265                         "for disk in 0 1 ; do ${dtype} dev ${disk} ;" \
 266                                 "for fs in fat ext2 ; do " \
 267                                         "${fs}load " \
 268                                                 "${dtype} ${disk}:1 " \
 269                                                 "10008000 " \
 270                                                 "/6x_bootscript" \
 271                                                 "&& source 10008000 ; " \
 272                                 "done ; " \
 273                         "done ; " \
 274                 "done; " \
 275                 "setenv stdout serial,vga ; " \
 276                 "echo ; echo 6x_bootscript not found ; " \
 277                 "echo ; echo serial console at 115200, 8N1 ; echo ; " \
 278                 "echo details at http://boundarydevices.com/6q_bootscript ; " \
 279                 "setenv stdout serial\0" \
 280         "upgradeu=for dtype in " CONFIG_DRIVE_TYPES \
 281                 "; do " \
 282                 "for disk in 0 1 ; do ${dtype} dev ${disk} ;" \
 283                      "for fs in fat ext2 ; do " \
 284                                 "${fs}load ${dtype} ${disk}:1 10008000 " \
 285                                         "/6x_upgrade " \
 286                                         "&& source 10008000 ; " \
 287                         "done ; " \
 288                 "done ; " \
 289         "done\0" \
 290
 291 #endif
 292 /* Miscellaneous configurable options */
 293 #define CONFIG_SYS_LONGHELP
 294 #define CONFIG_SYS_HUSH_PARSER
 295 #define CONFIG_SYS_PROMPT              "U-Boot > "
 296 #define CONFIG_AUTO_COMPLETE
 297 #define CONFIG_SYS_CBSIZE              1024
 298
 299 /* Print Buffer Size */
 300 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 301 #define CONFIG_SYS_MAXARGS             16
 302 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 303
 304 #define CONFIG_SYS_MEMTEST_START       0x10000000
 305 #define CONFIG_SYS_MEMTEST_END         0x10010000
 306 #define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
 307
 308 #define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
 309
 310 #define CONFIG_CMDLINE_EDITING
 311
 312 /* Physical Memory Map */
 313 #define CONFIG_NR_DRAM_BANKS           1
 314 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 315
 316 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 317 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 318 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 319
 320 #define CONFIG_SYS_INIT_SP_OFFSET \
 321         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 322 #define CONFIG_SYS_INIT_SP_ADDR \
 323         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 324
 325 /* FLASH and environment organization */
 326 #define CONFIG_SYS_NO_FLASH
 327
 328 #define CONFIG_ENV_SIZE                 (8 * 1024)
 329
 330 #if defined(CONFIG_SABRELITE)
 331 #define CONFIG_ENV_IS_IN_MMC
 332 #else
 333 #define CONFIG_ENV_IS_IN_SPI_FLASH
 334 #endif
 335
 336 #if defined(CONFIG_ENV_IS_IN_MMC)
 337 #define CONFIG_ENV_OFFSET               (6 * 64 * 1024)
 338 #define CONFIG_SYS_MMC_ENV_DEV          0
 339 #elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
 340 #define CONFIG_ENV_OFFSET               (768 * 1024)
 341 #define CONFIG_ENV_SECT_SIZE            (8 * 1024)
 342 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
 343 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
 344 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
 345 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
 346 #endif
 347
 348 #define CONFIG_OF_LIBFDT
 349 #define CONFIG_CMD_BOOTZ
 350
 351 #ifndef CONFIG_SYS_DCACHE_OFF
 352 #define CONFIG_CMD_CACHE
 353 #endif
 354
 355 #define CONFIG_CMD_BMP
 356
 357 #define CONFIG_CMD_TIME
 358 #define CONFIG_SYS_ALT_MEMTEST
 359
 360 #define CONFIG_CMD_BOOTZ
 361 #define CONFIG_SUPPORT_RAW_INITRD
 362 #define CONFIG_CMD_FS_GENERIC
 363
 364 #endif         /* __CONFIG_H */