extern void board_pll_init_f(void);
-/*
- * sdram_init - Dummy implementation for start.S, spd_sdram used on this board!
- */
-void sdram_init(void)
-{
- return;
-}
-
#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
static void cram_bcr_write(u32 wr_val)
{
return (CFG_MBYTES_RAM << 20);
}
-
-#ifndef CONFIG_NAND_SPL
-int testdram(void)
-{
- return (0);
-}
-#endif
#endif
}
-#if defined(CFG_DRAM_TEST)
-int testdram(void)
-{
- unsigned long *mem = (unsigned long *)0;
- const unsigned long kend = (1024 / sizeof(unsigned long));
- unsigned long k, n, *p32, ctr;
- const unsigned long bend = CFG_MBYTES_SDRAM * 1024 * 1024;
-
- mtmsr(0);
-
- for (k = 0; k < CFG_MBYTES_SDRAM*1024;
- ++k, mem += (1024 / sizeof(unsigned long))) {
- if ((k & 1023) == 0) {
- printf("%3d MB\r", k / 1024);
- }
-
- memset(mem, 0xaaaaaaaa, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0xaaaaaaaa) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
-
- memset(mem, 0x55555555, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0x55555555) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
- }
-
- /*
- * Perform a sequence test to ensure that all
- * memory locations are uniquely addressable
- */
- ctr = 0;
- p32 = 0;
- while ((unsigned long)p32 != bend) {
- if (0 == ((unsigned long)p32 & ((1<<20)-1)))
- printf("Writing %3d MB\r", (unsigned long)p32 >> 20);
- *p32++ = ctr++;
- }
-
- ctr = 0;
- p32 = 0;
- while ((unsigned long)p32 != bend) {
- if (0 == ((unsigned long)p32 & ((1<<20)-1)))
- printf("Verifying %3d MB\r", (unsigned long)p32 >> 20);
-
- if (*p32 != ctr) {
- printf("SDRAM test fails at: %08x\n", p32);
- return 1;
- }
-
- ctr++;
- p32++;
- }
-
- printf("SDRAM test passes\n");
- return 0;
-}
-#endif
-
/*************************************************************************
* pci_pre_init
*
return (0);
}
-/*
- * sdram_init - Dummy implementation for start.S, spd_sdram used on this board!
- */
-void sdram_init(void)
-{
- return;
-}
-
/* -------------------------------------------------------------------------
initdram(int board_type) reads EEPROM via I2c. EEPROM contains all of
the necessary info for SDRAM controller configuration
ret = spd_sdram();
return ret;
}
-
-int testdram(void)
-{
- /* TODO: XXX XXX XXX */
- printf("test: xxx MB - ok\n");
-
- return (0);
-}
}
#endif
-#if defined(CFG_DRAM_TEST)
-int testdram(void)
-{
- unsigned long *mem = (unsigned long *)0;
- const unsigned long kend = (1024 / sizeof(unsigned long));
- unsigned long k, n;
-
- mtmsr(0);
-
- for (k = 0; k < CFG_KBYTES_SDRAM;
- ++k, mem += (1024 / sizeof(unsigned long))) {
- if ((k & 1023) == 0) {
- printf("%3d MB\r", k / 1024);
- }
-
- memset(mem, 0xaaaaaaaa, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0xaaaaaaaa) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
-
- memset(mem, 0x55555555, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0x55555555) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
- }
- printf("SDRAM test passes\n");
- return 0;
-}
-#endif
-
/*
* pci_target_init
*
return dram_size;
}
-#if defined(CFG_DRAM_TEST)
-int testdram(void)
-{
- uint *pstart = (uint *) 0x00000000;
- uint *pend = (uint *) 0x08000000;
- uint *p;
-
- for (p = pstart; p < pend; p++)
- *p = 0xaaaaaaaa;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0xaaaaaaaa) {
- printf("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
-
- for (p = pstart; p < pend; p++)
- *p = 0x55555555;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0x55555555) {
- printf("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
- return 0;
-}
-#endif
-
#if !defined(CONFIG_SPD_EEPROM)
/*************************************************************************
* fixed sdram init -- doesn't use serial presence detect.
return (SDRAM_CLKTR_CLKP_90_DEG_ADV);
}
-#if defined(CFG_DRAM_TEST)
-int testdram (void)
-{
- uint *pstart = (uint *) 0x00000000;
- uint *pend = (uint *) 0x08000000;
- uint *p;
-
- for (p = pstart; p < pend; p++)
- *p = 0xaaaaaaaa;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0xaaaaaaaa) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
-
- for (p = pstart; p < pend; p++)
- *p = 0x55555555;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0x55555555) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
- return 0;
-}
-#endif
-
/*************************************************************************
* pci_pre_init
*
LIB = $(obj)lib$(BOARD).a
-COBJS = $(BOARD).o cmd_pll.o memory.o
-SOBJS = init.o
+COBJS = $(BOARD).o cmd_pll.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
+++ /dev/null
-/*
- * (C) Copyright 2007-2008
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * Based on code provided from UDTech and AMCC
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <ppc4xx.h>
-
-#include <ppc_asm.tmpl>
-#include <ppc_defs.h>
-
-#define mtsdram_as(reg, value) \
- addi r4,0,reg ; \
- mtdcr memcfga,r4 ; \
- addis r4,0,value@h ; \
- ori r4,r4,value@l ; \
- mtdcr memcfgd,r4 ;
-
- .globl ext_bus_cntlr_init
-ext_bus_cntlr_init:
-#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
-
- /*
- * DDR2 setup
- */
-
- /* Following the DDR Core Manual, here is the initialization */
-
- /* Step 1 */
-
- /* Step 2 */
-
- /* Step 3 */
-
- /* base=00000000, size=256MByte (6), mode=7 (n*10*8) */
- mtsdram_as(SDRAM_MB0CF, 0x00006701);
-
- /* SET SDRAM_MB1CF - Not enabled */
- mtsdram_as(SDRAM_MB1CF, 0x00000000);
-
- /* SET SDRAM_MB2CF - Not enabled */
- mtsdram_as(SDRAM_MB2CF, 0x00000000);
-
- /* SET SDRAM_MB3CF - Not enabled */
- mtsdram_as(SDRAM_MB3CF, 0x00000000);
-
- /* SDRAM_CLKTR: Adv Addr clock by 180 deg */
- mtsdram_as(SDRAM_CLKTR, 0x80000000);
-
- /* Refresh Time register (0x30) Refresh every 7.8125uS */
- mtsdram_as(SDRAM_RTR, 0x06180000);
-
- /* SDRAM_SDTR1 */
- mtsdram_as(SDRAM_SDTR1, 0x80201000);
-
- /* SDRAM_SDTR2 */
- mtsdram_as(SDRAM_SDTR2, 0x32204232);
-
- /* SDRAM_SDTR3 */
- mtsdram_as(SDRAM_SDTR3, 0x080b0d1a);
-
- mtsdram_as(SDRAM_MMODE, 0x00000442);
- mtsdram_as(SDRAM_MEMODE, 0x00000404);
-
- /* SDRAM0_MCOPT1 (0X20) No ECC Gen */
- mtsdram_as(SDRAM_MCOPT1, 0x04322000);
-
- /* NOP */
- mtsdram_as(SDRAM_INITPLR0, 0xa8380000);
- /* precharge 3 DDR clock cycle */
- mtsdram_as(SDRAM_INITPLR1, 0x81900400);
- /* EMR2 twr = 2tck */
- mtsdram_as(SDRAM_INITPLR2, 0x81020000);
- /* EMR3 twr = 2tck */
- mtsdram_as(SDRAM_INITPLR3, 0x81030000);
- /* EMR DLL ENABLE twr = 2tck */
- mtsdram_as(SDRAM_INITPLR4, 0x81010404);
- /* MR w/ DLL reset
- * Note: 5 is CL. May need to be changed
- */
- mtsdram_as(SDRAM_INITPLR5, 0x81000542);
- /* precharge 3 DDR clock cycle */
- mtsdram_as(SDRAM_INITPLR6, 0x81900400);
- /* Auto-refresh trfc = 26tck */
- mtsdram_as(SDRAM_INITPLR7, 0x8D080000);
- /* Auto-refresh trfc = 26tck */
- mtsdram_as(SDRAM_INITPLR8, 0x8D080000);
- /* Auto-refresh */
- mtsdram_as(SDRAM_INITPLR9, 0x8D080000);
- /* Auto-refresh */
- mtsdram_as(SDRAM_INITPLR10, 0x8D080000);
- /* MRS - normal operation; wait 2 cycle (set wait to tMRD) */
- mtsdram_as(SDRAM_INITPLR11, 0x81000442);
- mtsdram_as(SDRAM_INITPLR12, 0x81010780);
- mtsdram_as(SDRAM_INITPLR13, 0x81010400);
- mtsdram_as(SDRAM_INITPLR14, 0x00000000);
- mtsdram_as(SDRAM_INITPLR15, 0x00000000);
-
- /* SET MCIF0_CODT Die Termination On */
- mtsdram_as(SDRAM_CODT, 0x0080f837);
- mtsdram_as(SDRAM_MODT0, 0x01800000);
- mtsdram_as(SDRAM_MODT1, 0x00000000);
-
- mtsdram_as(SDRAM_WRDTR, 0x00000000);
-
- /* SDRAM0_MCOPT2 (0X21) Start initialization */
- mtsdram_as(SDRAM_MCOPT2, 0x20000000);
-
- /* Step 5 */
- lis r3,0x1 /* 400000 = wait 100ms */
- mtctr r3
-
-pll_wait:
- bdnz pll_wait
-
- /* Step 6 */
-
- /* SDRAM_DLCR */
- mtsdram_as(SDRAM_DLCR, 0x030000a5);
-
- /* SDRAM_RDCC */
- mtsdram_as(SDRAM_RDCC, 0x40000000);
-
- /* SDRAM_RQDC */
- mtsdram_as(SDRAM_RQDC, 0x80000038);
-
- /* SDRAM_RFDC */
- mtsdram_as(SDRAM_RFDC, 0x00000209);
-
- /* Enable memory controller */
- mtsdram_as(SDRAM_MCOPT2, 0x28000000);
-#endif /* #ifndef CONFIG_NAND_U_BOOT */
-
- blr
+++ /dev/null
-/*
- * (C) Copyright 2007
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/processor.h>
-#include <i2c.h>
-
-void sdram_init(void)
-{
- return;
-}
-
-long int initdram(int board_type)
-{
- return (CFG_MBYTES_SDRAM << 20);
-}
-
-#if defined(CFG_DRAM_TEST)
-int testdram (void)
-{
- printf ("testdram\n");
-#if defined (CONFIG_NAND_U_BOOT)
- return 0;
-#endif
- uint *pstart = (uint *) 0x00000000;
- uint *pend = (uint *) 0x00001000;
- uint *p;
-
- for (p = pstart; p < pend; p++) {
- *p = 0xaaaaaaaa;
- }
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0xaaaaaaaa) {
-#if !defined (CONFIG_NAND_SPL)
- printf ("SDRAM test fails at: %08x\n", (uint) p);
-#endif
- return 1;
- }
- }
-
- for (p = pstart; p < pend; p++) {
- *p = 0x55555555;
- }
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0x55555555) {
-#if !defined (CONFIG_NAND_SPL)
- printf ("SDRAM test fails at: %08x\n", (uint) p);
-#endif
- return 1;
- }
- }
-#if !defined (CONFIG_NAND_SPL)
- printf ("SDRAM test passed!!!\n");
-#endif
- return 0;
-}
-#endif
return (SDRAM_CLKTR_CLKP_180_DEG_ADV);
}
-/*************************************************************************
- * int testdram()
- *
- ************************************************************************/
-#if defined(CFG_DRAM_TEST)
-int testdram(void)
-{
- unsigned long *mem = (unsigned long *) 0;
- const unsigned long kend = (1024 / sizeof(unsigned long));
- unsigned long k, n;
-
- mtmsr(0);
-
- for (k = 0; k < CFG_KBYTES_SDRAM;
- ++k, mem += (1024 / sizeof(unsigned long))) {
- if ((k & 1023) == 0) {
- printf("%3d MB\r", k / 1024);
- }
-
- memset(mem, 0xaaaaaaaa, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0xaaaaaaaa) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
-
- memset(mem, 0x55555555, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0x55555555) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
- }
- printf("SDRAM test passes\n");
-
- return 0;
-}
-#endif
-
-
/*************************************************************************
* pci_pre_init
*
LIB = $(obj)lib$(BOARD).a
-COBJS = $(BOARD).o cmd_pll.o memory.o
+COBJS = $(BOARD).o cmd_pll.o
SOBJS = init.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
/*
+ * Copyright (c) 2008 Nuovation System Designs, LLC
+ * Grant Erickson <gerickson@nuovations.com>
+ *
* (C) Copyright 2007-2008
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
- * Based on code provided from Senao and AMCC
+ * Originally based on code provided from Senao and AMCC
*
* See file CREDITS for list of people who contributed to this
* project.
* MA 02111-1307 USA
*/
-#include <config.h>
-#include <ppc4xx.h>
-
-#include <ppc_asm.tmpl>
-#include <ppc_defs.h>
-
-#define mtsdram_as(reg, value) \
- addi r4,0,reg ; \
- mtdcr memcfga,r4 ; \
- addis r4,0,value@h ; \
- ori r4,r4,value@l ; \
- mtdcr memcfgd,r4 ;
-
.globl ext_bus_cntlr_init
ext_bus_cntlr_init:
-
- /*
- * DDR2 setup
- */
-
- /* Following the DDR Core Manual, here is the initialization */
-
- /* Step 1 */
-
- /* Step 2 */
-
- /* Step 3 */
-
- /* base=00000000, size=128MByte (5), mode=2 (n*10*4) */
- mtsdram_as(SDRAM_MB0CF, 0x00005201);
-
- /* base=08000000, size=128MByte (5), mode=2 (n*10*4) */
- mtsdram_as(SDRAM_MB1CF, (0x08000000 >> 3) | 0x5201);
-
- /* SDRAM_CLKTR: Adv Addr clock by 180 deg */
- mtsdram_as(SDRAM_CLKTR,0x80000000);
-
- /* Refresh Time register (0x30) Refresh every 7.8125uS */
- mtsdram_as(SDRAM_RTR, 0x06180000);
-
- /* SDRAM_SDTR1 */
- mtsdram_as(SDRAM_SDTR1, 0x80201000);
-
- /* SDRAM_SDTR2 */
- mtsdram_as(SDRAM_SDTR2, 0x32204232);
-
- /* SDRAM_SDTR3 */
- mtsdram_as(SDRAM_SDTR3, 0x080b0d1a);
-
- mtsdram_as(SDRAM_MMODE, 0x00000442);
- mtsdram_as(SDRAM_MEMODE, 0x00000404);
-
- /* SDRAM0_MCOPT1 (0X20) No ECC Gen */
- mtsdram_as(SDRAM_MCOPT1, 0x04322000);
-
- /* NOP */
- mtsdram_as(SDRAM_INITPLR0, 0xa8380000);
- /* precharge 3 DDR clock cycle */
- mtsdram_as(SDRAM_INITPLR1, 0x81900400);
- /* EMR2 twr = 2tck */
- mtsdram_as(SDRAM_INITPLR2, 0x81020000);
- /* EMR3 twr = 2tck */
- mtsdram_as(SDRAM_INITPLR3, 0x81030000);
- /* EMR DLL ENABLE twr = 2tck */
- mtsdram_as(SDRAM_INITPLR4, 0x81010404);
- /* MR w/ DLL reset
- * Note: 5 is CL. May need to be changed
- */
- mtsdram_as(SDRAM_INITPLR5, 0x81000542);
- /* precharge 3 DDR clock cycle */
- mtsdram_as(SDRAM_INITPLR6, 0x81900400);
- /* Auto-refresh trfc = 26tck */
- mtsdram_as(SDRAM_INITPLR7, 0x8D080000);
- /* Auto-refresh trfc = 26tck */
- mtsdram_as(SDRAM_INITPLR8, 0x8D080000);
- /* Auto-refresh */
- mtsdram_as(SDRAM_INITPLR9, 0x8D080000);
- /* Auto-refresh */
- mtsdram_as(SDRAM_INITPLR10, 0x8D080000);
- /* MRS - normal operation; wait 2 cycle (set wait to tMRD) */
- mtsdram_as(SDRAM_INITPLR11, 0x81000442);
- mtsdram_as(SDRAM_INITPLR12, 0x81010780);
- mtsdram_as(SDRAM_INITPLR13, 0x81010400);
- mtsdram_as(SDRAM_INITPLR14, 0x00000000);
- mtsdram_as(SDRAM_INITPLR15, 0x00000000);
-
- /* SET MCIF0_CODT Die Termination On */
- mtsdram_as(SDRAM_CODT, 0x0080f837);
- mtsdram_as(SDRAM_MODT0, 0x01800000);
-#if 0 /* test-only: not sure if 0 is ok when 2nd bank is used */
- mtsdram_as(SDRAM_MODT1, 0x00000000);
-#endif
-
- mtsdram_as(SDRAM_WRDTR, 0x00000000);
-
- /* SDRAM0_MCOPT2 (0X21) Start initialization */
- mtsdram_as(SDRAM_MCOPT2, 0x20000000);
-
- /* Step 5 */
- lis r3,0x1 /* 400000 = wait 100ms */
- mtctr r3
-
-pll_wait:
- bdnz pll_wait
-
- /* Step 6 */
-
- /* SDRAM_DLCR */
- mtsdram_as(SDRAM_DLCR, 0x030000a5);
-
- /* SDRAM_RDCC */
- mtsdram_as(SDRAM_RDCC, 0x40000000);
-
- /* SDRAM_RQDC */
- mtsdram_as(SDRAM_RQDC, 0x80000038);
-
- /* SDRAM_RFDC */
- mtsdram_as(SDRAM_RFDC, 0x00000209);
-
- /* Enable memory controller */
- mtsdram_as(SDRAM_MCOPT2, 0x28000000);
-
blr
+++ /dev/null
-/*
- * (C) Copyright 2007
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/processor.h>
-
-void sdram_init(void)
-{
- return;
-}
-
-long int initdram(int board_type)
-{
- /*
- * Same as on Kilauea, Makalu generates exception 0x200
- * (machine check) after trap_init() in board_init_f,
- * when SDRAM is initialized here (late) and d-cache is
- * used earlier as INIT_RAM.
- * So for now, initialize DDR2 in init.S very early and
- * also use it for INIT_RAM. Then this exception doesn't
- * occur.
- */
-#if 0
- u32 val;
-
- /* base=00000000, size=128MByte (5), mode=2 (n*10*4) */
- mtsdram(SDRAM_MB0CF, 0x00005201);
-
- /* SET SDRAM_MB1CF - Not enabled */
- mtsdram(SDRAM_MB1CF, 0x00000000);
-
- /* SET SDRAM_MB2CF - Not enabled */
- mtsdram(SDRAM_MB2CF, 0x00000000);
-
- /* SET SDRAM_MB3CF - Not enabled */
- mtsdram(SDRAM_MB3CF, 0x00000000);
-
- /* SDRAM_CLKTR: Adv Addr clock by 90 deg */
- mtsdram(SDRAM_CLKTR, 0x80000000);
-
- /* Refresh Time register (0x30) Refresh every 7.8125uS */
- mtsdram(SDRAM_RTR, 0x06180000);
-
- /* SDRAM_SDTR1 */
- mtsdram(SDRAM_SDTR1, 0x80201000);
-
- /* SDRAM_SDTR2 */
- mtsdram(SDRAM_SDTR2, 0x32204232);
-
- /* SDRAM_SDTR3 */
- mtsdram(SDRAM_SDTR3, 0x080b0d1a);
-
- mtsdram(SDRAM_MMODE, 0x00000442);
- mtsdram(SDRAM_MEMODE, 0x00000404);
-
- /* SDRAM0_MCOPT1 (0X20) No ECC Gen */
- mtsdram(SDRAM_MCOPT1, 0x04322000);
-
- /* NOP */
- mtsdram(SDRAM_INITPLR0, 0xa8380000);
- /* precharge 3 DDR clock cycle */
- mtsdram(SDRAM_INITPLR1, 0x81900400);
- /* EMR2 twr = 2tck */
- mtsdram(SDRAM_INITPLR2, 0x81020000);
- /* EMR3 twr = 2tck */
- mtsdram(SDRAM_INITPLR3, 0x81030000);
- /* EMR DLL ENABLE twr = 2tck */
- mtsdram(SDRAM_INITPLR4, 0x81010404);
- /* MR w/ DLL reset
- * Note: 5 is CL. May need to be changed
- */
- mtsdram(SDRAM_INITPLR5, 0x81000542);
- /* precharge 3 DDR clock cycle */
- mtsdram(SDRAM_INITPLR6, 0x81900400);
- /* Auto-refresh trfc = 26tck */
- mtsdram(SDRAM_INITPLR7, 0x8D080000);
- /* Auto-refresh trfc = 26tck */
- mtsdram(SDRAM_INITPLR8, 0x8D080000);
- /* Auto-refresh */
- mtsdram(SDRAM_INITPLR9, 0x8D080000);
- /* Auto-refresh */
- mtsdram(SDRAM_INITPLR10, 0x8D080000);
- /* MRS - normal operation; wait 2 cycle (set wait to tMRD) */
- mtsdram(SDRAM_INITPLR11, 0x81000442);
- mtsdram(SDRAM_INITPLR12, 0x81010780);
- mtsdram(SDRAM_INITPLR13, 0x81010400);
- mtsdram(SDRAM_INITPLR14, 0x00000000);
- mtsdram(SDRAM_INITPLR15, 0x00000000);
-
- /* SET MCIF0_CODT Die Termination On */
- mtsdram(SDRAM_CODT, 0x0080f837);
- mtsdram(SDRAM_MODT0, 0x01800000);
- mtsdram(SDRAM_MODT1, 0x00000000);
-
- mtsdram(SDRAM_WRDTR, 0x00000000);
-
- /* SDRAM0_MCOPT2 (0X21) Start initialization */
- mtsdram(SDRAM_MCOPT2, 0x20000000);
-
- /* Step 5 */
- do {
- mfsdram(SDRAM_MCSTAT, val);
- } while ((val & SDRAM_MCSTAT_MIC_COMP) != SDRAM_MCSTAT_MIC_COMP);
-
- /* Step 6 */
-
- /* SDRAM_DLCR */
- mtsdram(SDRAM_DLCR, 0x030000a5);
-
- /* SDRAM_RDCC */
- mtsdram(SDRAM_RDCC, 0x40000000);
-
- /* SDRAM_RQDC */
- mtsdram(SDRAM_RQDC, 0x80000038);
-
- /* SDRAM_RFDC */
- mtsdram(SDRAM_RFDC, 0x00000209);
-
- /* Enable memory controller */
- mfsdram(SDRAM_MCOPT2, val);
- val |= SDRAM_MCOPT2_DCEN_ENABLE;
- mtsdram(SDRAM_MCOPT2, val);
-#endif
- return (CFG_MBYTES_SDRAM << 20);
-}
-
-#if defined(CFG_DRAM_TEST)
-int testdram (void)
-{
- printf ("testdram\n");
-#if defined (CONFIG_NAND_U_BOOT)
- return 0;
-#endif
- uint *pstart = (uint *) 0x00000000;
- uint *pend = (uint *) 0x00001000;
- uint *p;
-
- for (p = pstart; p < pend; p++) {
- *p = 0xaaaaaaaa;
- }
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0xaaaaaaaa) {
-#if !defined (CONFIG_NAND_SPL)
- printf ("SDRAM test fails at: %08x\n", (uint) p);
-#endif
- return 1;
- }
- }
-
- for (p = pstart; p < pend; p++) {
- *p = 0x55555555;
- }
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0x55555555) {
-#if !defined (CONFIG_NAND_SPL)
- printf ("SDRAM test fails at: %08x\n", (uint) p);
-#endif
- return 1;
- }
- }
-#if !defined (CONFIG_NAND_SPL)
- printf ("SDRAM test passed!!!\n");
-#endif
- return 0;
-}
-#endif
}
-#if defined(CFG_DRAM_TEST)
-int testdram (void)
-{
- uint *pstart = (uint *) 0x00000000;
- uint *pend = (uint *) 0x08000000;
- uint *p;
-
- for (p = pstart; p < pend; p++)
- *p = 0xaaaaaaaa;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0xaaaaaaaa) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
-
- for (p = pstart; p < pend; p++)
- *p = 0x55555555;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0x55555555) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
- return 0;
-}
-#endif
-
#if !defined(CONFIG_SPD_EEPROM)
/*************************************************************************
* fixed sdram init -- doesn't use serial presence detect.
ifndef TEXT_BASE
TEXT_BASE = 0xFFFA0000
+#
+# When defining CONFIG_VIDEO, TEXT_BASE needs to be 0xFFF80000
+# TEXT_BASE = 0xFFF80000
+#
endif
PLATFORM_CPPFLAGS += -DCONFIG_440=1
return (0);
}
-#if defined(CFG_DRAM_TEST)
-int testdram(void)
-{
- unsigned long *mem = (unsigned long *)0;
- const unsigned long kend = (1024 / sizeof(unsigned long));
- unsigned long k, n;
-
- mtmsr(0);
-
- for (k = 0; k < CFG_MBYTES_SDRAM;
- ++k, mem += (1024 / sizeof(unsigned long))) {
- if ((k & 1023) == 0) {
- printf("%3d MB\r", k / 1024);
- }
-
- memset(mem, 0xaaaaaaaa, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0xaaaaaaaa) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
-
- memset(mem, 0x55555555, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0x55555555) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
- }
- printf("SDRAM test passes\n");
- return 0;
-}
-#endif
-
#if defined(CONFIG_PCI) && defined(CONFIG_PCI_PNP)
/*
* Assign interrupts to PCI devices.
return 1;
}
#endif /* CONFIG_PCI */
-
-#ifdef CFG_DRAM_TEST
-int testdram(void)
-{
- unsigned long *mem = (unsigned long *)0;
- const unsigned long kend = (1024 / sizeof(unsigned long));
- unsigned long k, n;
- unsigned long msr;
- unsigned long total_kbytes = CFG_SDRAM_SIZE_PER_BANK * CFG_SDRAM_BANKS / 1024;
-
- msr = mfmsr();
- mtmsr(msr & ~(MSR_EE));
-
- for (k = 0; k < total_kbytes ;
- ++k, mem += (1024 / sizeof(unsigned long))) {
- if ((k & 1023) == 0)
- printf("%3d MB\r", k / 1024);
-
- memset(mem, 0xaaaaaaaa, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0xaaaaaaaa) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
-
- memset(mem, 0x55555555, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0x55555555) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
- }
- printf("SDRAM test passes\n");
- mtmsr(msr);
-
- return 0;
-}
-#endif /* CFG_DRAM_TEST */
return (0);
}
-#if defined(CFG_DRAM_TEST)
-int testdram (void)
-{
- uint *pstart = (uint *) 0x04000000;
- uint *pend = (uint *) 0x0fc00000;
- uint *p;
-
- for (p = pstart; p < pend; p++)
- *p = 0xaaaaaaaa;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0xaaaaaaaa) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
-
- for (p = pstart; p < pend; p++)
- *p = 0x55555555;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0x55555555) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
- return 0;
-}
-#endif
-
/*************************************************************************
* pci_pre_init
*
return (0);
}
-/*
- * sdram_init - Dummy implementation for start.S, spd_sdram used on this board!
- */
-void sdram_init(void)
-{
- return;
-}
-
/*
* initdram(int board_type) reads EEPROM via I2c. EEPROM contains all of
* the necessary info for SDRAM controller configuration
{
return spd_sdram();
}
-
-int testdram(void)
-{
- /* TODO: XXX XXX XXX */
- printf("test: xxx MB - ok\n");
-
- return (0);
-}
}
/*************************************************************************
- * sdram_init -- doesn't use serial presence detect.
+ * initdram -- doesn't use serial presence detect.
*
* Assumes: 256 MB, ECC, non-registered
* PLB @ 133 MHz
*tr1_value = (first_good + last_bad) / 2;
}
-void sdram_init(void)
+long int initdram(int board)
{
register uint reg;
int tr1_bank1, tr1_bank2;
sdram_tr1_set(0x00000000, &tr1_bank1);
sdram_tr1_set(0x08000000, &tr1_bank2);
- mtsdram(mem_tr1, (((tr1_bank1+tr1_bank2)/2) | 0x80800800) );
-}
+ mtsdram(mem_tr1, (((tr1_bank1+tr1_bank2)/2) | 0x80800800));
-/*************************************************************************
- * long int initdram
- *
- ************************************************************************/
-long int initdram(int board)
-{
- sdram_init();
return CFG_SDRAM_BANKS * (CFG_KBYTES_SDRAM * 1024); /* return bytes */
}
-#if defined(CFG_DRAM_TEST)
-int testdram(void)
-{
- unsigned long *mem = (unsigned long *)0;
- const unsigned long kend = (1024 / sizeof(unsigned long));
- unsigned long k, n;
-
- mtmsr(0);
-
- for (k = 0; k < CFG_KBYTES_SDRAM;
- ++k, mem += (1024 / sizeof(unsigned long))) {
- if ((k & 1023) == 0) {
- printf("%3d MB\r", k / 1024);
- }
-
- memset(mem, 0xaaaaaaaa, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0xaaaaaaaa) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
-
- memset(mem, 0x55555555, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0x55555555) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
- }
- printf("SDRAM test passes\n");
- return 0;
-}
-#endif
-
/*************************************************************************
* pci_pre_init
*
return default_val;
}
-#if defined(CFG_DRAM_TEST)
-int testdram (void)
-{
- uint *pstart = (uint *) 0x00000000;
- uint *pend = (uint *) 0x08000000;
- uint *p;
-
- for (p = pstart; p < pend; p++)
- *p = 0xaaaaaaaa;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0xaaaaaaaa) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
-
- for (p = pstart; p < pend; p++)
- *p = 0x55555555;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0x55555555) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
- return 0;
-}
-#endif
-
/*************************************************************************
* pci_pre_init
*
.globl ext_bus_cntlr_init
ext_bus_cntlr_init:
blr
-
- .globl sdram_init
-sdram_init:
- blr
mtdcr ebccfgd,r4
blr
-
-/*----------------------------------------------------------------------------- */
-/* Function: sdram_init */
-/* Description: Configures SDRAM memory banks. */
-/* NOTE: for CrayL1 we have ECC memory, so enable it. */
-/*....now done in C in L1.c:init_sdram for readability. */
-/*----------------------------------------------------------------------------- */
- .globl sdram_init
-
-sdram_init:
- blr
#include <miiphy.h>
#include <ppc4xx_enet.h>
+void sdram_init(void);
+
/*
* Configuration data for AMIS FS6377-01 Programmable 3-PLL Clock Generator
*
ulong bank_size;
ulong tmp;
+ /*
+ * ToDo: Move the asm init routine sdram_init() to this C file,
+ * or even better use some common ppc4xx code available
+ * in cpu/ppc4xx
+ */
+ sdram_init();
+
tot_size = 0;
mtdcr (memcfga, mem_mb0cf);
#include <miiphy.h>
#include <ppc4xx_enet.h>
+void sdram_init(void);
+
/*
* board_early_init_f: do early board initialization
*
ulong bank_size;
ulong tmp;
+ /*
+ * ToDo: Move the asm init routine sdram_init() to this C file,
+ * or even better use some common ppc4xx code available
+ * in cpu/ppc4xx
+ */
+ sdram_init();
+
tot_size = 0;
mtdcr (memcfga, mem_mb0cf);
#define PPC405GP_GPIO0_ODR 0xef600718 /* GPIO Open Drain */
#define PPC405GP_GPIO0_IR 0xef60071c /* GPIO Input */
+void sdram_init(void);
+
int board_early_init_f (void)
{
int TotalSize;
#endif
+ /*
+ * ToDo: Move the asm init routine sdram_init() to this C file,
+ * or even better use some common ppc4xx code available
+ * in cpu/ppc4xx
+ */
+ sdram_init();
#ifdef CONFIG_ERIC
/*
return 0;
}
-/* ------------------------------------------------------------------------- */
-
-long int initdram (int board_type)
-{
- unsigned long val;
-
- mtdcr(memcfga, mem_mb0cf);
- val = mfdcr(memcfgd);
-
- return (4*1024*1024 << ((val & 0x000e0000) >> 17));
-}
-
-/* ------------------------------------------------------------------------- */
-
-int testdram (void)
-{
- /* TODO: XXX XXX XXX */
- printf ("test: 16 MB - ok\n");
-
- return (0);
-}
-
#if 1 /* test-only: some internal test routines... */
/*
return 0;
}
-
-/* ------------------------------------------------------------------------- */
-
-long int initdram (int board_type)
-{
- return (16 * 1024 * 1024);
-}
-
-/* ------------------------------------------------------------------------- */
-
-int testdram (void)
-{
- /* TODO: XXX XXX XXX */
- printf ("test: 16 MB - ok\n");
-
- return (0);
-}
-
-/* ------------------------------------------------------------------------- */
#include <common.h>
#include "exbitgen.h"
+void sdram_init(void);
+
/* ************************************************************************ */
int board_early_init_f (void)
/* ------------------------------------------------------------------------ --
ulong bank_size;
ulong tmp;
+ /*
+ * ToDo: Move the asm init routine sdram_init() to this C file,
+ * or even better use some common ppc4xx code available
+ * in cpu/ppc4xx
+ */
+ sdram_init();
+
tot_size = 0;
mtdcr (memcfga, mem_mb0cf);
}
-#if 1 /* test-only */
-void sdram_init(void)
-{
- init_sdram_static_settings();
-}
-#endif
-
-
-#if 0 /* test-only */
-long int initdram (int board_type)
-{
- unsigned long val;
-
- mtdcr(memcfga, mem_mb0cf);
- val = mfdcr(memcfgd);
-
-#if 0
- printf("\nmb0cf=%x\n", val); /* test-only */
- printf("strap=%x\n", mfdcr(strap)); /* test-only */
-#endif
-
- return (4*1024*1024 << ((val & 0x000e0000) >> 17));
-}
-#endif
-
-
-int testdram (void)
-{
- /* TODO: XXX XXX XXX */
- printf ("test: 16 MB - ok\n");
-
- return (0);
-}
-
-
#if defined(CONFIG_CMD_NAND)
#include <linux/mtd/nand_legacy.h>
extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
mtdcr ebccfgd,r4
blr
-
-
-/*----------------------------------------------------------------------- */
-/* Function: sdram_init */
-/* Description: This function is called by cpu/ppc4xx/start.S code */
-/* to get the SDRAM initialized. */
-/*----------------------------------------------------------------------- */
- .globl sdram_init
-sdram_init:
- blr
return (0);
}
-#if defined(CFG_DRAM_TEST)
-int testdram(void)
-{
- unsigned long *mem = (unsigned long *)0;
- const unsigned long kend = (1024 / sizeof(unsigned long));
- unsigned long k, n;
-
- mtmsr(0);
-
- for (k = 0; k < CFG_MBYTES_SDRAM;
- ++k, mem += (1024 / sizeof(unsigned long))) {
- if ((k & 1023) == 0) {
- printf("%3d MB\r", k / 1024);
- }
-
- memset(mem, 0xaaaaaaaa, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0xaaaaaaaa) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
-
- memset(mem, 0x55555555, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0x55555555) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
- }
- printf("SDRAM test passes\n");
- return 0;
-}
-#endif
-
/*************************************************************************
* pci_pre_init
*
.globl ext_bus_cntlr_init
ext_bus_cntlr_init:
blr
-
- .globl sdram_init
-sdram_init:
- blr
nop /* pass2 DCR errata #8 */
blr
-/*-----------------------------------------------------------------------------
- * Function: sdram_init
- * Description: Configures the internal SRAM memory. and setup the
- * Stackpointer in it.
- *----------------------------------------------------------------------------- */
- .globl sdram_init
-
-sdram_init:
-
-
- blr
-
-
#if defined(CONFIG_BOOT_PCI)
.section .bootpg,"ax"
.globl _start_pci
nop /* pass2 DCR errata #8 */
blr
-/*-----------------------------------------------------------------------------
- * Function: sdram_init
- * Description: Configures the internal SRAM memory. and setup the
- * Stackpointer in it.
- *----------------------------------------------------------------------------- */
- .globl sdram_init
-
-sdram_init:
-
-
- blr
-
-
#if defined(CONFIG_BOOT_PCI)
.section .bootpg,"ax"
.globl _start_pci
out_be32((u32 *)GPIO0_OR, tmp);
}
-/*
- * sdram_init - Dummy implementation for start.S, spd_sdram or initdram
- * used for HCUx
- */
-void sdram_init(void)
-{
- return;
-}
-
/*
* hcu_get_slot
*/
void hcu_led_set(u32 value);
void dcbz_area(u32 start_address, u32 num_bytes);
-#define DDR_DCR_BASE 0x10
-#define ddrcfga (DDR_DCR_BASE+0x0) /* DDR configuration address reg */
-#define ddrcfgd (DDR_DCR_BASE+0x1) /* DDR configuration data reg */
-
-#define DDR0_01_INT_MASK_MASK 0x000000FF
-#define DDR0_00_INT_ACK_ALL 0x7F000000
-#define DDR0_01_INT_MASK_ALL_ON 0x000000FF
-#define DDR0_01_INT_MASK_ALL_OFF 0x00000000
-
-#define DDR0_17_DLLLOCKREG_MASK 0x00010000 /* Read only */
-#define DDR0_17_DLLLOCKREG_UNLOCKED 0x00000000
-#define DDR0_17_DLLLOCKREG_LOCKED 0x00010000
-
-#define DDR0_22 0x16
-/* ECC */
-#define DDR0_22_CTRL_RAW_MASK 0x03000000
-#define DDR0_22_CTRL_RAW_ECC_DISABLE 0x00000000 /* ECC not enabled */
-#define DDR0_22_CTRL_RAW_ECC_CHECK_ONLY 0x01000000 /* ECC no correction */
-#define DDR0_22_CTRL_RAW_NO_ECC_RAM 0x02000000 /* Not a ECC RAM*/
-#define DDR0_22_CTRL_RAW_ECC_ENABLE 0x03000000 /* ECC correcting on */
-#define DDR0_03_CASLAT_DECODE(n) ((((unsigned long)(n))>>16)&0x7)
-
#define ECC_RAM 0x03267F0B
#define NO_ECC_RAM 0x00267F0B
/* -----------------------------------------------------------+
* Wait for the DCC master delay line to finish calibration
* ----------------------------------------------------------*/
- mtdcr(ddrcfga, DDR0_17);
+ mtdcr(memcfga, DDR0_17);
val = DDR0_17_DLLLOCKREG_UNLOCKED;
while (wait != 0xffff) {
- val = mfdcr(ddrcfgd);
+ val = mfdcr(memcfgd);
if ((val & DDR0_17_DLLLOCKREG_MASK) ==
DDR0_17_DLLLOCKREG_LOCKED)
/* dlllockreg bit on */
out_be16((u16 *)MCU25_LED_REGISTER_ADDRESS, value);
}
-/*
- * sdram_init - Dummy implementation for start.S, spd_sdram or initdram
- * used for HCUx
- */
-void sdram_init(void)
-{
- return;
-}
-
/*
* hcu_get_slot
*/
return dram_size;
}
-#if defined(CFG_DRAM_TEST)
-int testdram(void)
-{
- unsigned long *mem = (unsigned long *)0;
- const unsigned long kend = (1024 / sizeof(unsigned long));
- unsigned long k, n;
-
- mtmsr(0);
-
- for (k = 0; k < CFG_KBYTES_SDRAM;
- ++k, mem += (1024 / sizeof(unsigned long))) {
- if ((k & 1023) == 0) {
- printf("%3d MB\r", k / 1024);
- }
-
- memset(mem, 0xaaaaaaaa, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0xaaaaaaaa) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
-
- memset(mem, 0x55555555, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0x55555555) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
- }
- printf("SDRAM test passes\n");
- return 0;
-}
-#endif
-
/*************************************************************************
* pci_pre_init
*
return (0);
}
-#if defined(CFG_DRAM_TEST)
-int testdram (void)
-{
- uint *pstart = (uint *) 0x00000000;
- uint *pend = (uint *) 0x08000000;
- uint *p;
-
- for (p = pstart; p < pend; p++)
- *p = 0xaaaaaaaa;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0xaaaaaaaa) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
-
- for (p = pstart; p < pend; p++)
- *p = 0x55555555;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0x55555555) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
- return 0;
-}
-#endif
-
/*************************************************************************
* pci_pre_init
*
#include <watchdog.h>
unsigned long get_dram_size (void);
+void sdram_init(void);
/*
* Macros to transform values
long int initdram (int board_type)
{
+ /*
+ * ToDo: Move the asm init routine sdram_init() to this C file,
+ * or even better use some common ppc4xx code available
+ * in cpu/ppc4xx
+ */
+ sdram_init();
+
return get_dram_size ();
}
.globl ext_bus_cntlr_init
ext_bus_cntlr_init:
blr
-
- .globl sdram_init
-sdram_init:
- blr
return detect_sdram_size();
}
-#if defined(CFG_DRAM_TEST)
-int testdram(void)
-{
- unsigned long *mem = (unsigned long *)0;
- const unsigned long kend = (1024 / sizeof(unsigned long));
- unsigned long k, n;
- unsigned long msr;
- unsigned long total_kbytes;
-
- total_kbytes = detect_sdram_size();
-
- msr = mfmsr();
- mtmsr(msr & ~(MSR_EE));
-
- for (k = 0; k < total_kbytes ;
- ++k, mem += (1024 / sizeof(unsigned long))) {
- if ((k & 1023) == 0) {
- printf("%3d MB\r", k / 1024);
- }
-
- memset(mem, 0xaaaaaaaa, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0xaaaaaaaa) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
-
- memset(mem, 0x55555555, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0x55555555) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
- }
- printf("SDRAM test passes\n");
- mtmsr(msr);
-
- return 0;
-}
-#endif
-
static int default_env_var(char *buf, char *var)
{
char *ptr;
#include <ppc4xx.h>
#include <asm/mmu.h>
+#include "ecc.h"
+
#if defined(CONFIG_SPD_EEPROM) && \
(defined(CONFIG_440GP) || defined(CONFIG_440GX) || \
defined(CONFIG_440EP) || defined(CONFIG_440GR))
}
void spd_ddr_init_hang (void) __attribute__((weak, alias("__spd_ddr_init_hang")));
-/*-----------------------------------------------------------------------------
- | Memory Controller Options 0
- +-----------------------------------------------------------------------------*/
-#define SDRAM_CFG0_DCEN 0x80000000 /* SDRAM Controller Enable */
-#define SDRAM_CFG0_MCHK_MASK 0x30000000 /* Memory data errchecking mask */
-#define SDRAM_CFG0_MCHK_NON 0x00000000 /* No ECC generation */
-#define SDRAM_CFG0_MCHK_GEN 0x20000000 /* ECC generation */
-#define SDRAM_CFG0_MCHK_CHK 0x30000000 /* ECC generation and checking */
-#define SDRAM_CFG0_RDEN 0x08000000 /* Registered DIMM enable */
-#define SDRAM_CFG0_PMUD 0x04000000 /* Page management unit */
-#define SDRAM_CFG0_DMWD_MASK 0x02000000 /* DRAM width mask */
-#define SDRAM_CFG0_DMWD_32 0x00000000 /* 32 bits */
-#define SDRAM_CFG0_DMWD_64 0x02000000 /* 64 bits */
-#define SDRAM_CFG0_UIOS_MASK 0x00C00000 /* Unused IO State */
-#define SDRAM_CFG0_PDP 0x00200000 /* Page deallocation policy */
-
-/*-----------------------------------------------------------------------------
- | Memory Controller Options 1
- +-----------------------------------------------------------------------------*/
-#define SDRAM_CFG1_SRE 0x80000000 /* Self-Refresh Entry */
-#define SDRAM_CFG1_PMEN 0x40000000 /* Power Management Enable */
-
-/*-----------------------------------------------------------------------------+
- | SDRAM DEVPOT Options
- +-----------------------------------------------------------------------------*/
-#define SDRAM_DEVOPT_DLL 0x80000000
-#define SDRAM_DEVOPT_DS 0x40000000
-
-/*-----------------------------------------------------------------------------+
- | SDRAM MCSTS Options
- +-----------------------------------------------------------------------------*/
-#define SDRAM_MCSTS_MRSC 0x80000000
-#define SDRAM_MCSTS_SRMS 0x40000000
-#define SDRAM_MCSTS_CIS 0x20000000
-
-/*-----------------------------------------------------------------------------
- | SDRAM Refresh Timer Register
- +-----------------------------------------------------------------------------*/
-#define SDRAM_RTR_RINT_MASK 0xFFFF0000
-#define SDRAM_RTR_RINT_ENCODE(n) (((n) << 16) & SDRAM_RTR_RINT_MASK)
-#define sdram_HZ_to_ns(hertz) (1000000000/(hertz))
-
-/*-----------------------------------------------------------------------------+
- | SDRAM UABus Base Address Reg
- +-----------------------------------------------------------------------------*/
-#define SDRAM_UABBA_UBBA_MASK 0x0000000F
-
-/*-----------------------------------------------------------------------------+
- | Memory Bank 0-7 configuration
- +-----------------------------------------------------------------------------*/
-#define SDRAM_BXCR_SDBA_MASK 0xff800000 /* Base address */
-#define SDRAM_BXCR_SDSZ_MASK 0x000e0000 /* Size */
-#define SDRAM_BXCR_SDSZ_8 0x00020000 /* 8M */
-#define SDRAM_BXCR_SDSZ_16 0x00040000 /* 16M */
-#define SDRAM_BXCR_SDSZ_32 0x00060000 /* 32M */
-#define SDRAM_BXCR_SDSZ_64 0x00080000 /* 64M */
-#define SDRAM_BXCR_SDSZ_128 0x000a0000 /* 128M */
-#define SDRAM_BXCR_SDSZ_256 0x000c0000 /* 256M */
-#define SDRAM_BXCR_SDSZ_512 0x000e0000 /* 512M */
-#define SDRAM_BXCR_SDAM_MASK 0x0000e000 /* Addressing mode */
-#define SDRAM_BXCR_SDAM_1 0x00000000 /* Mode 1 */
-#define SDRAM_BXCR_SDAM_2 0x00002000 /* Mode 2 */
-#define SDRAM_BXCR_SDAM_3 0x00004000 /* Mode 3 */
-#define SDRAM_BXCR_SDAM_4 0x00006000 /* Mode 4 */
-#define SDRAM_BXCR_SDBE 0x00000001 /* Memory Bank Enable */
-
-/*-----------------------------------------------------------------------------+
- | SDRAM TR0 Options
- +-----------------------------------------------------------------------------*/
-#define SDRAM_TR0_SDWR_MASK 0x80000000
-#define SDRAM_TR0_SDWR_2_CLK 0x00000000
-#define SDRAM_TR0_SDWR_3_CLK 0x80000000
-#define SDRAM_TR0_SDWD_MASK 0x40000000
-#define SDRAM_TR0_SDWD_0_CLK 0x00000000
-#define SDRAM_TR0_SDWD_1_CLK 0x40000000
-#define SDRAM_TR0_SDCL_MASK 0x01800000
-#define SDRAM_TR0_SDCL_2_0_CLK 0x00800000
-#define SDRAM_TR0_SDCL_2_5_CLK 0x01000000
-#define SDRAM_TR0_SDCL_3_0_CLK 0x01800000
-#define SDRAM_TR0_SDPA_MASK 0x000C0000
-#define SDRAM_TR0_SDPA_2_CLK 0x00040000
-#define SDRAM_TR0_SDPA_3_CLK 0x00080000
-#define SDRAM_TR0_SDPA_4_CLK 0x000C0000
-#define SDRAM_TR0_SDCP_MASK 0x00030000
-#define SDRAM_TR0_SDCP_2_CLK 0x00000000
-#define SDRAM_TR0_SDCP_3_CLK 0x00010000
-#define SDRAM_TR0_SDCP_4_CLK 0x00020000
-#define SDRAM_TR0_SDCP_5_CLK 0x00030000
-#define SDRAM_TR0_SDLD_MASK 0x0000C000
-#define SDRAM_TR0_SDLD_1_CLK 0x00000000
-#define SDRAM_TR0_SDLD_2_CLK 0x00004000
-#define SDRAM_TR0_SDRA_MASK 0x0000001C
-#define SDRAM_TR0_SDRA_6_CLK 0x00000000
-#define SDRAM_TR0_SDRA_7_CLK 0x00000004
-#define SDRAM_TR0_SDRA_8_CLK 0x00000008
-#define SDRAM_TR0_SDRA_9_CLK 0x0000000C
-#define SDRAM_TR0_SDRA_10_CLK 0x00000010
-#define SDRAM_TR0_SDRA_11_CLK 0x00000014
-#define SDRAM_TR0_SDRA_12_CLK 0x00000018
-#define SDRAM_TR0_SDRA_13_CLK 0x0000001C
-#define SDRAM_TR0_SDRD_MASK 0x00000003
-#define SDRAM_TR0_SDRD_2_CLK 0x00000001
-#define SDRAM_TR0_SDRD_3_CLK 0x00000002
-#define SDRAM_TR0_SDRD_4_CLK 0x00000003
-
-/*-----------------------------------------------------------------------------+
- | SDRAM TR1 Options
- +-----------------------------------------------------------------------------*/
-#define SDRAM_TR1_RDSS_MASK 0xC0000000
-#define SDRAM_TR1_RDSS_TR0 0x00000000
-#define SDRAM_TR1_RDSS_TR1 0x40000000
-#define SDRAM_TR1_RDSS_TR2 0x80000000
-#define SDRAM_TR1_RDSS_TR3 0xC0000000
-#define SDRAM_TR1_RDSL_MASK 0x00C00000
-#define SDRAM_TR1_RDSL_STAGE1 0x00000000
-#define SDRAM_TR1_RDSL_STAGE2 0x00400000
-#define SDRAM_TR1_RDSL_STAGE3 0x00800000
-#define SDRAM_TR1_RDCD_MASK 0x00000800
-#define SDRAM_TR1_RDCD_RCD_0_0 0x00000000
-#define SDRAM_TR1_RDCD_RCD_1_2 0x00000800
-#define SDRAM_TR1_RDCT_MASK 0x000001FF
-#define SDRAM_TR1_RDCT_ENCODE(x) (((x) << 0) & SDRAM_TR1_RDCT_MASK)
-#define SDRAM_TR1_RDCT_DECODE(x) (((x) & SDRAM_TR1_RDCT_MASK) >> 0)
-#define SDRAM_TR1_RDCT_MIN 0x00000000
-#define SDRAM_TR1_RDCT_MAX 0x000001FF
-
-/*-----------------------------------------------------------------------------+
- | SDRAM WDDCTR Options
- +-----------------------------------------------------------------------------*/
-#define SDRAM_WDDCTR_WRCP_MASK 0xC0000000
-#define SDRAM_WDDCTR_WRCP_0DEG 0x00000000
-#define SDRAM_WDDCTR_WRCP_90DEG 0x40000000
-#define SDRAM_WDDCTR_WRCP_180DEG 0x80000000
-#define SDRAM_WDDCTR_DCD_MASK 0x000001FF
-
-/*-----------------------------------------------------------------------------+
- | SDRAM CLKTR Options
- +-----------------------------------------------------------------------------*/
-#define SDRAM_CLKTR_CLKP_MASK 0xC0000000
-#define SDRAM_CLKTR_CLKP_0DEG 0x00000000
-#define SDRAM_CLKTR_CLKP_90DEG 0x40000000
-#define SDRAM_CLKTR_CLKP_180DEG 0x80000000
-#define SDRAM_CLKTR_DCDT_MASK 0x000001FF
-
-/*-----------------------------------------------------------------------------+
- | SDRAM DLYCAL Options
- +-----------------------------------------------------------------------------*/
-#define SDRAM_DLYCAL_DLCV_MASK 0x000003FC
-#define SDRAM_DLYCAL_DLCV_ENCODE(x) (((x)<<2) & SDRAM_DLYCAL_DLCV_MASK)
-#define SDRAM_DLYCAL_DLCV_DECODE(x) (((x) & SDRAM_DLYCAL_DLCV_MASK)>>2)
-
/*-----------------------------------------------------------------------------+
| General Definition
+-----------------------------------------------------------------------------*/
unsigned long num_dimm_banks);
static void program_tr1(void);
-#ifdef CONFIG_DDR_ECC
-static void program_ecc(unsigned long num_bytes);
-#endif
-
static unsigned long program_bxcr(unsigned long *dimm_populated,
unsigned char *iic0_dimm_addr,
unsigned long num_dimm_banks);
/*
* If ecc is enabled, initialize the parity bits.
*/
- program_ecc(total_size);
+ ecc_init(CFG_SDRAM_BASE, total_size);
#endif
return total_size;
return(bank_base_addr);
}
-
-#ifdef CONFIG_DDR_ECC
-static void program_ecc(unsigned long num_bytes)
-{
- unsigned long bank_base_addr;
- unsigned long current_address;
- unsigned long end_address;
- unsigned long address_increment;
- unsigned long cfg0;
-
- /*
- * get Memory Controller Options 0 data
- */
- mfsdram(mem_cfg0, cfg0);
-
- /*
- * reset the bank_base address
- */
- bank_base_addr = CFG_SDRAM_BASE;
-
- if ((cfg0 & SDRAM_CFG0_MCHK_MASK) != SDRAM_CFG0_MCHK_NON) {
- mtsdram(mem_cfg0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) | SDRAM_CFG0_MCHK_GEN);
-
- if ((cfg0 & SDRAM_CFG0_DMWD_MASK) == SDRAM_CFG0_DMWD_32)
- address_increment = 4;
- else
- address_increment = 8;
-
- current_address = (unsigned long)(bank_base_addr);
- end_address = (unsigned long)(bank_base_addr) + num_bytes;
-
- while (current_address < end_address) {
- *((unsigned long*)current_address) = 0x00000000;
- current_address += address_increment;
- }
-
- mtsdram(mem_cfg0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) |
- SDRAM_CFG0_MCHK_CHK);
- }
-}
-#endif /* CONFIG_DDR_ECC */
#endif /* CONFIG_SPD_EEPROM */
* This SPD SDRAM detection code supports AMCC PPC44x cpu's with a
* DDR2 controller (non Denali Core). Those currently are:
*
- * 405: 405EX
+ * 405: 405EX(r)
* 440/460: 440SP/440SPe/460EX/460GT
*
+ * Copyright (c) 2008 Nuovation System Designs, LLC
+ * Grant Erickson <gerickson@nuovations.com>
+
* (C) Copyright 2007-2008
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
#include <asm/mmu.h>
#include <asm/cache.h>
+#include "ecc.h"
+
#if defined(CONFIG_SPD_EEPROM) && \
(defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
defined(CONFIG_460EX) || defined(CONFIG_460GT))
dcr_data = mfdcr(SDRAM_R3BAS);
printf(" MQ3_B0BAS = 0x%08X\n", dcr_data);
}
-#else
+#else /* !defined(DEBUG) */
static void ppc440sp_sdram_register_dump(void)
{
}
-#endif
-#endif /* CONFIG_SPD_EEPROM */
+#endif /* defined(DEBUG) */
+#elif defined(CONFIG_405EX)
+/*-----------------------------------------------------------------------------
+ * Function: initdram
+ * Description: Configures the PPC405EX(r) DDR1/DDR2 SDRAM memory
+ * banks. The configuration is performed using static, compile-
+ * time parameters.
+ *---------------------------------------------------------------------------*/
+long initdram(int board_type)
+{
+ /*
+ * Only run this SDRAM init code once. For NAND booting
+ * targets like Kilauea, we call initdram() early from the
+ * 4k NAND booting image (CONFIG_NAND_SPL) from nand_boot().
+ * Later on the NAND U-Boot image runs (CONFIG_NAND_U_BOOT)
+ * which calls initdram() again. This time the controller
+ * mustn't be reconfigured again since we're already running
+ * from SDRAM.
+ */
+#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
+ unsigned long val;
+
+ /* Set Memory Bank Configuration Registers */
+
+ mtsdram(SDRAM_MB0CF, CFG_SDRAM0_MB0CF);
+ mtsdram(SDRAM_MB1CF, CFG_SDRAM0_MB1CF);
+ mtsdram(SDRAM_MB2CF, CFG_SDRAM0_MB2CF);
+ mtsdram(SDRAM_MB3CF, CFG_SDRAM0_MB3CF);
+
+ /* Set Memory Clock Timing Register */
+
+ mtsdram(SDRAM_CLKTR, CFG_SDRAM0_CLKTR);
+
+ /* Set Refresh Time Register */
+
+ mtsdram(SDRAM_RTR, CFG_SDRAM0_RTR);
+
+ /* Set SDRAM Timing Registers */
+
+ mtsdram(SDRAM_SDTR1, CFG_SDRAM0_SDTR1);
+ mtsdram(SDRAM_SDTR2, CFG_SDRAM0_SDTR2);
+ mtsdram(SDRAM_SDTR3, CFG_SDRAM0_SDTR3);
+
+ /* Set Mode and Extended Mode Registers */
+
+ mtsdram(SDRAM_MMODE, CFG_SDRAM0_MMODE);
+ mtsdram(SDRAM_MEMODE, CFG_SDRAM0_MEMODE);
+
+ /* Set Memory Controller Options 1 Register */
+
+ mtsdram(SDRAM_MCOPT1, CFG_SDRAM0_MCOPT1);
+
+ /* Set Manual Initialization Control Registers */
+
+ mtsdram(SDRAM_INITPLR0, CFG_SDRAM0_INITPLR0);
+ mtsdram(SDRAM_INITPLR1, CFG_SDRAM0_INITPLR1);
+ mtsdram(SDRAM_INITPLR2, CFG_SDRAM0_INITPLR2);
+ mtsdram(SDRAM_INITPLR3, CFG_SDRAM0_INITPLR3);
+ mtsdram(SDRAM_INITPLR4, CFG_SDRAM0_INITPLR4);
+ mtsdram(SDRAM_INITPLR5, CFG_SDRAM0_INITPLR5);
+ mtsdram(SDRAM_INITPLR6, CFG_SDRAM0_INITPLR6);
+ mtsdram(SDRAM_INITPLR7, CFG_SDRAM0_INITPLR7);
+ mtsdram(SDRAM_INITPLR8, CFG_SDRAM0_INITPLR8);
+ mtsdram(SDRAM_INITPLR9, CFG_SDRAM0_INITPLR9);
+ mtsdram(SDRAM_INITPLR10, CFG_SDRAM0_INITPLR10);
+ mtsdram(SDRAM_INITPLR11, CFG_SDRAM0_INITPLR11);
+ mtsdram(SDRAM_INITPLR12, CFG_SDRAM0_INITPLR12);
+ mtsdram(SDRAM_INITPLR13, CFG_SDRAM0_INITPLR13);
+ mtsdram(SDRAM_INITPLR14, CFG_SDRAM0_INITPLR14);
+ mtsdram(SDRAM_INITPLR15, CFG_SDRAM0_INITPLR15);
+
+ /* Set On-Die Termination Registers */
+
+ mtsdram(SDRAM_CODT, CFG_SDRAM0_CODT);
+ mtsdram(SDRAM_MODT0, CFG_SDRAM0_MODT0);
+ mtsdram(SDRAM_MODT1, CFG_SDRAM0_MODT1);
+
+ /* Set Write Timing Register */
+
+ mtsdram(SDRAM_WRDTR, CFG_SDRAM0_WRDTR);
+
+ /*
+ * Start Initialization by SDRAM0_MCOPT2[SREN] = 0 and
+ * SDRAM0_MCOPT2[IPTR] = 1
+ */
+
+ mtsdram(SDRAM_MCOPT2, (SDRAM_MCOPT2_SREN_EXIT |
+ SDRAM_MCOPT2_IPTR_EXECUTE));
+
+ /*
+ * Poll SDRAM0_MCSTAT[MIC] for assertion to indicate the
+ * completion of initialization.
+ */
+
+ do {
+ mfsdram(SDRAM_MCSTAT, val);
+ } while ((val & SDRAM_MCSTAT_MIC_MASK) != SDRAM_MCSTAT_MIC_COMP);
+
+ /* Set Delay Control Registers */
+
+ mtsdram(SDRAM_DLCR, CFG_SDRAM0_DLCR);
+ mtsdram(SDRAM_RDCC, CFG_SDRAM0_RDCC);
+ mtsdram(SDRAM_RQDC, CFG_SDRAM0_RQDC);
+ mtsdram(SDRAM_RFDC, CFG_SDRAM0_RFDC);
+
+ /*
+ * Enable Controller by SDRAM0_MCOPT2[DCEN] = 1:
+ */
+
+ mfsdram(SDRAM_MCOPT2, val);
+ mtsdram(SDRAM_MCOPT2, val | SDRAM_MCOPT2_DCEN_ENABLE);
+
+#if defined(CONFIG_DDR_ECC)
+ ecc_init(CFG_SDRAM_BASE, CFG_MBYTES_SDRAM << 20);
+#endif /* defined(CONFIG_DDR_ECC) */
+#endif /* !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) */
+
+ return (CFG_MBYTES_SDRAM << 20);
+}
+#endif /* defined(CONFIG_SPD_EEPROM) && defined(CONFIG_440SP) || ... */
#define UDIV_SUBTRACT 0
#define UART0_SDR sdr_uart0
#define UART1_SDR sdr_uart1
-#if defined(CONFIG_440EP) || defined(CONFIG_440EPx) || \
- defined(CONFIG_440GR) || defined(CONFIG_440GRx) || \
- defined(CONFIG_440SP) || defined(CONFIG_440SPe) || \
+#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
+ defined(CONFIG_440GR) || defined(CONFIG_440GRX) || \
+ defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
defined(CONFIG_460EX) || defined(CONFIG_460GT)
#define UART2_SDR sdr_uart2
#endif
-#if defined(CONFIG_440EP) || defined(CONFIG_440EPx) || \
- defined(CONFIG_440GR) || defined(CONFIG_440GRx) || \
+#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
+ defined(CONFIG_440GR) || defined(CONFIG_440GRX) || \
defined(CONFIG_460EX) || defined(CONFIG_460GT)
#define UART3_SDR sdr_uart3
#endif
COBJS += cpu_init.o
COBJS += denali_data_eye.o
COBJS += denali_spd_ddr2.o
+COBJS += ecc.o
COBJS += fdt.o
COBJS += gpio.o
COBJS += i2c.o
DECLARE_GLOBAL_DATA_PTR;
#endif
-#ifdef CFG_INIT_DCACHE_CS
-# if (CFG_INIT_DCACHE_CS == 0)
-# define PBxAP pb0ap
-# define PBxCR pb0cr
-# if (defined(CFG_EBC_PB0AP) && defined(CFG_EBC_PB0CR))
-# define PBxAP_VAL CFG_EBC_PB0AP
-# define PBxCR_VAL CFG_EBC_PB0CR
-# endif
-# endif
-# if (CFG_INIT_DCACHE_CS == 1)
-# define PBxAP pb1ap
-# define PBxCR pb1cr
-# if (defined(CFG_EBC_PB1AP) && defined(CFG_EBC_PB1CR))
-# define PBxAP_VAL CFG_EBC_PB1AP
-# define PBxCR_VAL CFG_EBC_PB1CR
-# endif
-# endif
-# if (CFG_INIT_DCACHE_CS == 2)
-# define PBxAP pb2ap
-# define PBxCR pb2cr
-# if (defined(CFG_EBC_PB2AP) && defined(CFG_EBC_PB2CR))
-# define PBxAP_VAL CFG_EBC_PB2AP
-# define PBxCR_VAL CFG_EBC_PB2CR
-# endif
-# endif
-# if (CFG_INIT_DCACHE_CS == 3)
-# define PBxAP pb3ap
-# define PBxCR pb3cr
-# if (defined(CFG_EBC_PB3AP) && defined(CFG_EBC_PB3CR))
-# define PBxAP_VAL CFG_EBC_PB3AP
-# define PBxCR_VAL CFG_EBC_PB3CR
-# endif
-# endif
-# if (CFG_INIT_DCACHE_CS == 4)
-# define PBxAP pb4ap
-# define PBxCR pb4cr
-# if (defined(CFG_EBC_PB4AP) && defined(CFG_EBC_PB4CR))
-# define PBxAP_VAL CFG_EBC_PB4AP
-# define PBxCR_VAL CFG_EBC_PB4CR
-# endif
-# endif
-# if (CFG_INIT_DCACHE_CS == 5)
-# define PBxAP pb5ap
-# define PBxCR pb5cr
-# if (defined(CFG_EBC_PB5AP) && defined(CFG_EBC_PB5CR))
-# define PBxAP_VAL CFG_EBC_PB5AP
-# define PBxCR_VAL CFG_EBC_PB5CR
-# endif
-# endif
-# if (CFG_INIT_DCACHE_CS == 6)
-# define PBxAP pb6ap
-# define PBxCR pb6cr
-# if (defined(CFG_EBC_PB6AP) && defined(CFG_EBC_PB6CR))
-# define PBxAP_VAL CFG_EBC_PB6AP
-# define PBxCR_VAL CFG_EBC_PB6CR
-# endif
-# endif
-# if (CFG_INIT_DCACHE_CS == 7)
-# define PBxAP pb7ap
-# define PBxCR pb7cr
-# if (defined(CFG_EBC_PB7AP) && defined(CFG_EBC_PB7CR))
-# define PBxAP_VAL CFG_EBC_PB7AP
-# define PBxCR_VAL CFG_EBC_PB7CR
-# endif
-# endif
-#endif /* CFG_INIT_DCACHE_CS */
-
#ifndef CFG_PLL_RECONFIG
#define CFG_PLL_RECONFIG 0
#endif
uint pvr = get_pvr();
#endif
-#ifdef CFG_INIT_DCACHE_CS
- /*
- * Flush and invalidate dcache, then disable CS for temporary stack.
- * Afterwards, this CS can be used for other purposes
- */
- dcache_disable(); /* flush and invalidate dcache */
- mtebc(PBxAP, 0);
- mtebc(PBxCR, 0); /* disable CS for temporary stack */
-
-#if (defined(PBxAP_VAL) && defined(PBxCR_VAL))
- /*
- * Write new value into CS register
- */
- mtebc(PBxAP, PBxAP_VAL);
- mtebc(PBxCR, PBxCR_VAL);
-#endif
-#endif /* CFG_INIT_DCACHE_CS */
-
/*
* Write Ethernetaddress into on-chip register
*/
--- /dev/null
+/*
+ * Copyright (c) 2008 Nuovation System Designs, LLC
+ * Grant Erickson <gerickson@nuovations.com>
+ *
+ * (C) Copyright 2005-2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * (C) Copyright 2002
+ * Jun Gu, Artesyn Technology, jung@artesyncp.com
+ *
+ * (C) Copyright 2001
+ * Bill Hunter, Wave 7 Optics, williamhunter@attbi.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will abe useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Description:
+ * This file implements generic DRAM ECC initialization for
+ * PowerPC processors using a SDRAM DDR/DDR2 controller,
+ * including the 405EX(r), 440GP/GX/EP/GR, 440SP(E), and
+ * 460EX/GT.
+ */
+
+#include <common.h>
+#include <ppc4xx.h>
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+
+#include "ecc.h"
+
+#if defined(CONFIG_SDRAM_PPC4xx_IBM_DDR) || \
+ defined(CONFIG_SDRAM_PPC4xx_IBM_DDR2)
+#if defined(CONFIG_DDR_ECC) || defined(CONFIG_SDRAM_ECC)
+/*
+ * void ecc_init()
+ *
+ * Description:
+ * This routine initializes a range of DRAM ECC memory with known
+ * data and enables ECC checking.
+ *
+ * TO DO:
+ * - Improve performance by utilizing cache.
+ * - Further generalize to make usable by other 4xx variants (e.g.
+ * 440EPx, et al).
+ *
+ * Input(s):
+ * start - A pointer to the start of memory covered by ECC requiring
+ * initialization.
+ * size - The size, in bytes, of the memory covered by ECC requiring
+ * initialization.
+ *
+ * Output(s):
+ * start - A pointer to the start of memory covered by ECC with
+ * CFG_ECC_PATTERN written to all locations and ECC data
+ * primed.
+ *
+ * Returns:
+ * N/A
+ */
+void ecc_init(unsigned long * const start, unsigned long size)
+{
+ const unsigned long pattern = CFG_ECC_PATTERN;
+ unsigned long * const end = (unsigned long * const)((long)start + size);
+ unsigned long * current = start;
+ unsigned long mcopt1;
+ long increment;
+
+ if (start >= end)
+ return;
+
+ mfsdram(SDRAM_ECC_CFG, mcopt1);
+
+ /* Enable ECC generation without checking or reporting */
+
+ mtsdram(SDRAM_ECC_CFG, ((mcopt1 & ~SDRAM_ECC_CFG_MCHK_MASK) |
+ SDRAM_ECC_CFG_MCHK_GEN));
+
+ increment = sizeof(u32);
+
+#if defined(CONFIG_440)
+ /*
+ * Look at the geometry of SDRAM (data width) to determine whether we
+ * can skip words when writing.
+ */
+
+ if ((mcopt1 & SDRAM_ECC_CFG_DMWD_MASK) != SDRAM_ECC_CFG_DMWD_32)
+ increment = sizeof(u64);
+#endif /* defined(CONFIG_440) */
+
+ while (current < end) {
+ *current = pattern;
+ current = (unsigned long *)((long)current + increment);
+ }
+
+ /* Wait until the writes are finished. */
+
+ sync();
+
+ /* Enable ECC generation with checking and no reporting */
+
+ mtsdram(SDRAM_ECC_CFG, ((mcopt1 & ~SDRAM_ECC_CFG_MCHK_MASK) |
+ SDRAM_ECC_CFG_MCHK_CHK));
+}
+#endif /* defined(CONFIG_DDR_ECC) || defined(CONFIG_SDRAM_ECC) */
+#endif /* defined(CONFIG_SDRAM_PPC4xx_IBM_DDR)... */
--- /dev/null
+/*
+ * Copyright (c) 2008 Nuovation System Designs, LLC
+ * Grant Erickson <gerickson@nuovations.com>
+ *
+ * Copyright (c) 2007 DENX Software Engineering, GmbH
+ * Stefan Roese <sr@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will abe useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Description:
+ * This file implements ECC initialization for PowerPC processors
+ * using the SDRAM DDR2 controller, including the 405EX(r),
+ * 440SP(E), 460EX and 460GT.
+ *
+ */
+
+#ifndef _ECC_H_
+#define _ECC_H_
+
+#if !defined(CFG_ECC_PATTERN)
+#define CFG_ECC_PATTERN 0x00000000
+#endif /* !defined(CFG_ECC_PATTERN) */
+
+/*
+ * Since the IBM DDR controller used on 440GP/GX/EP/GR is not register
+ * compatible to the IBM DDR/2 controller used on 405EX/440SP/SPe/460EX/GT
+ * we need to make some processor dependant defines used later on by the
+ * driver.
+ */
+
+/* For 440GP/GX/EP/GR */
+#if defined(CONFIG_SDRAM_PPC4xx_IBM_DDR)
+#define SDRAM_ECC_CFG SDRAM_CFG0
+#define SDRAM_ECC_CFG_MCHK_MASK SDRAM_CFG0_MCHK_MASK
+#define SDRAM_ECC_CFG_MCHK_GEN SDRAM_CFG0_MCHK_GEN
+#define SDRAM_ECC_CFG_MCHK_CHK SDRAM_CFG0_MCHK_CHK
+#define SDRAM_ECC_CFG_DMWD_MASK SDRAM_CFG0_DMWD_MASK
+#define SDRAM_ECC_CFG_DMWD_32 SDRAM_CFG0_DMWD_32
+#endif
+
+/* For 405EX/440SP/SPe/460EX/GT */
+#if defined(CONFIG_SDRAM_PPC4xx_IBM_DDR2)
+#define SDRAM_ECC_CFG SDRAM_MCOPT1
+#define SDRAM_ECC_CFG_MCHK_MASK SDRAM_MCOPT1_MCHK_MASK
+#define SDRAM_ECC_CFG_MCHK_GEN SDRAM_MCOPT1_MCHK_GEN
+#define SDRAM_ECC_CFG_MCHK_CHK SDRAM_MCOPT1_MCHK_CHK
+#define SDRAM_ECC_CFG_DMWD_MASK SDRAM_MCOPT1_DMWD_MASK
+#define SDRAM_ECC_CFG_DMWD_32 SDRAM_MCOPT1_DMWD_32
+#endif
+
+extern void ecc_init(unsigned long * const start, unsigned long size);
+
+#endif /* _ECC_H_ */
#include <ppc4xx.h>
#include <asm/processor.h>
#include "sdram.h"
+#include "ecc.h"
#ifdef CONFIG_SDRAM_BANK0
/*
* Autodetect onboard SDRAM on 405 platforms
*/
-void sdram_init(void)
+long int initdram(int board_type)
{
ulong speed;
ulong sdtr1;
mtsdram(mem_mcopt1, 0);
}
#endif
- return;
+
+ /*
+ * OK, size detected -> all done
+ */
+ return mb0cf[i].size;
}
}
+
+ return 0;
}
#else /* CONFIG_440 */
*tr1_value = (first_good + last_bad) / 2;
}
-#ifdef CONFIG_SDRAM_ECC
-static void ecc_init(ulong start, ulong size)
-{
- ulong current_addr; /* current byte address */
- ulong end_addr; /* end of memory region */
- ulong addr_inc; /* address skip between writes */
- ulong cfg0_reg; /* for restoring ECC state */
-
- /*
- * TODO: Enable dcache before running this test (speedup)
- */
-
- mfsdram(mem_cfg0, cfg0_reg);
- mtsdram(mem_cfg0, (cfg0_reg & ~SDRAM_CFG0_MEMCHK) | SDRAM_CFG0_MEMCHK_GEN);
-
- /*
- * look at geometry of SDRAM (data width) to determine whether we
- * can skip words when writing
- */
- if ((cfg0_reg & SDRAM_CFG0_DRAMWDTH) == SDRAM_CFG0_DRAMWDTH_32)
- addr_inc = 4;
- else
- addr_inc = 8;
-
- current_addr = start;
- end_addr = start + size;
-
- while (current_addr < end_addr) {
- *((ulong *)current_addr) = 0x00000000;
- current_addr += addr_inc;
- }
-
- /*
- * TODO: Flush dcache and disable it again
- */
-
- /*
- * Enable ecc checking and parity errors
- */
- mtsdram(mem_cfg0, (cfg0_reg & ~SDRAM_CFG0_MEMCHK) | SDRAM_CFG0_MEMCHK_CHK);
-}
-#endif
-
/*
* Autodetect onboard DDR SDRAM on 440 platforms
*
* Copyright (C) 1999 Magnus Damm <kieraypc01.p.y.kie.era.ericsson.se>
* Copyright (C) 2000,2001,2002 Wolfgang Denk <wd@denx.de>
* Copyright (C) 2007 Stefan Roese <sr@denx.de>, DENX Software Engineering
+ * Copyright (c) 2008 Nuovation System Designs, LLC
+ * Grant Erickson <gerickson@nuovations.com>
*
* See file CREDITS for list of people who contributed to this
* project.
# if (CFG_INIT_DCACHE_CS == 0)
# define PBxAP pb0ap
# define PBxCR pb0cr
+# if (defined(CFG_EBC_PB0AP) && defined(CFG_EBC_PB0CR))
+# define PBxAP_VAL CFG_EBC_PB0AP
+# define PBxCR_VAL CFG_EBC_PB0CR
+# endif
# endif
# if (CFG_INIT_DCACHE_CS == 1)
# define PBxAP pb1ap
# define PBxCR pb1cr
+# if (defined(CFG_EBC_PB1AP) && defined(CFG_EBC_PB1CR))
+# define PBxAP_VAL CFG_EBC_PB1AP
+# define PBxCR_VAL CFG_EBC_PB1CR
+# endif
# endif
# if (CFG_INIT_DCACHE_CS == 2)
# define PBxAP pb2ap
# define PBxCR pb2cr
+# if (defined(CFG_EBC_PB2AP) && defined(CFG_EBC_PB2CR))
+# define PBxAP_VAL CFG_EBC_PB2AP
+# define PBxCR_VAL CFG_EBC_PB2CR
+# endif
# endif
# if (CFG_INIT_DCACHE_CS == 3)
# define PBxAP pb3ap
# define PBxCR pb3cr
+# if (defined(CFG_EBC_PB3AP) && defined(CFG_EBC_PB3CR))
+# define PBxAP_VAL CFG_EBC_PB3AP
+# define PBxCR_VAL CFG_EBC_PB3CR
+# endif
# endif
# if (CFG_INIT_DCACHE_CS == 4)
# define PBxAP pb4ap
# define PBxCR pb4cr
+# if (defined(CFG_EBC_PB4AP) && defined(CFG_EBC_PB4CR))
+# define PBxAP_VAL CFG_EBC_PB4AP
+# define PBxCR_VAL CFG_EBC_PB4CR
+# endif
# endif
# if (CFG_INIT_DCACHE_CS == 5)
# define PBxAP pb5ap
# define PBxCR pb5cr
+# if (defined(CFG_EBC_PB5AP) && defined(CFG_EBC_PB5CR))
+# define PBxAP_VAL CFG_EBC_PB5AP
+# define PBxCR_VAL CFG_EBC_PB5CR
+# endif
# endif
# if (CFG_INIT_DCACHE_CS == 6)
# define PBxAP pb6ap
# define PBxCR pb6cr
+# if (defined(CFG_EBC_PB6AP) && defined(CFG_EBC_PB6CR))
+# define PBxAP_VAL CFG_EBC_PB6AP
+# define PBxCR_VAL CFG_EBC_PB6CR
+# endif
# endif
# if (CFG_INIT_DCACHE_CS == 7)
# define PBxAP pb7ap
# define PBxCR pb7cr
+# if (defined(CFG_EBC_PB7AP) && defined(CFG_EBC_PB7CR))
+# define PBxAP_VAL CFG_EBC_PB7AP
+# define PBxCR_VAL CFG_EBC_PB7CR
+# endif
+# endif
+# ifndef PBxAP_VAL
+# define PBxAP_VAL 0
+# endif
+# ifndef PBxCR_VAL
+# define PBxCR_VAL 0
+# endif
+/*
+ * Memory Bank x (nothingness) initialization CFG_INIT_RAM_ADDR + 64 MiB
+ * used as temporary stack pointer for the primordial stack
+ */
+# ifndef CFG_INIT_DCACHE_PBxAR
+# define CFG_INIT_DCACHE_PBxAR (EBC_BXAP_BME_DISABLED | \
+ EBC_BXAP_TWT_ENCODE(7) | \
+ EBC_BXAP_BCE_DISABLE | \
+ EBC_BXAP_BCT_2TRANS | \
+ EBC_BXAP_CSN_ENCODE(0) | \
+ EBC_BXAP_OEN_ENCODE(0) | \
+ EBC_BXAP_WBN_ENCODE(0) | \
+ EBC_BXAP_WBF_ENCODE(0) | \
+ EBC_BXAP_TH_ENCODE(2) | \
+ EBC_BXAP_RE_DISABLED | \
+ EBC_BXAP_SOR_NONDELAYED | \
+ EBC_BXAP_BEM_WRITEONLY | \
+ EBC_BXAP_PEN_DISABLED)
+# endif /* CFG_INIT_DCACHE_PBxAR */
+# ifndef CFG_INIT_DCACHE_PBxCR
+# define CFG_INIT_DCACHE_PBxCR (EBC_BXCR_BAS_ENCODE(CFG_INIT_RAM_ADDR) | \
+ EBC_BXCR_BS_64MB | \
+ EBC_BXCR_BU_RW | \
+ EBC_BXCR_BW_16BIT)
+# endif /* CFG_INIT_DCACHE_PBxCR */
+# ifndef CFG_INIT_RAM_PATTERN
+# define CFG_INIT_RAM_PATTERN 0xDEADDEAD
# endif
#endif /* CFG_INIT_DCACHE_CS */
#error Only 4k of init-ram is supported - please adjust CFG_INIT_RAM_END!
#endif
+/*
+ * Unless otherwise overriden, enable two 128MB cachable instruction regions
+ * at CFG_SDRAM_BASE and another 128MB cacheable instruction region covering
+ * NOR flash at CFG_FLASH_BASE. Disable all cacheable data regions.
+ */
+#if !defined(CFG_FLASH_BASE)
+/* If not already defined, set it to the "last" 128MByte region */
+# define CFG_FLASH_BASE 0xf8000000
+#endif
+#if !defined(CFG_ICACHE_SACR_VALUE)
+# define CFG_ICACHE_SACR_VALUE \
+ (PPC_128MB_SACR_VALUE(CFG_SDRAM_BASE + ( 0 << 20)) | \
+ PPC_128MB_SACR_VALUE(CFG_SDRAM_BASE + (128 << 20)) | \
+ PPC_128MB_SACR_VALUE(CFG_FLASH_BASE))
+#endif /* !defined(CFG_ICACHE_SACR_VALUE) */
+
+#if !defined(CFG_DCACHE_SACR_VALUE)
+# define CFG_DCACHE_SACR_VALUE \
+ (0x00000000)
+#endif /* !defined(CFG_DCACHE_SACR_VALUE) */
+
#define function_prolog(func_name) .text; \
.align 2; \
.globl func_name; \
.extern ext_bus_cntlr_init
- .extern sdram_init
#ifdef CONFIG_NAND_U_BOOT
.extern reconfig_tlb0
#endif
/* Continue from 'normal' start */
/*----------------------------------------------------------------*/
2:
-
-#if defined(CONFIG_NAND_SPL)
-#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
- defined(CONFIG_460EX) || defined(CONFIG_460GT)
- /*
- * Enable internal SRAM (only on 440EPx/GRx, 440EP/GR have no OCM)
- */
- lis r2,0x7fff
- ori r2,r2,0xffff
- mfdcr r1,isram0_dpc
- and r1,r1,r2 /* Disable parity check */
- mtdcr isram0_dpc,r1
- mfdcr r1,isram0_pmeg
- and r1,r1,r2 /* Disable pwr mgmt */
- mtdcr isram0_pmeg,r1
-#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
- lis r1,0x4000 /* BAS = 8000_0000 */
- ori r1,r1,0x4580 /* 16k */
- mtdcr isram0_sb0cr,r1
-#endif
-#endif
-#if defined(CONFIG_440EP)
- /*
- * On 440EP with no internal SRAM, we setup SDRAM very early
- * and copy the NAND_SPL to SDRAM and jump to it
- */
- /* Clear Dcache to use as RAM */
- addis r3,r0,CFG_INIT_RAM_ADDR@h
- ori r3,r3,CFG_INIT_RAM_ADDR@l
- addis r4,r0,CFG_INIT_RAM_END@h
- ori r4,r4,CFG_INIT_RAM_END@l
- rlwinm. r5,r4,0,27,31
- rlwinm r5,r4,27,5,31
- beq ..d_ran3
- addi r5,r5,0x0001
-..d_ran3:
- mtctr r5
-..d_ag3:
- dcbz r0,r3
- addi r3,r3,32
- bdnz ..d_ag3
- /*----------------------------------------------------------------*/
- /* Setup the stack in internal SRAM */
- /*----------------------------------------------------------------*/
- lis r1,CFG_INIT_RAM_ADDR@h
- ori r1,r1,CFG_INIT_SP_OFFSET@l
- li r0,0
- stwu r0,-4(r1)
- stwu r0,-4(r1) /* Terminate call chain */
-
- stwu r1,-8(r1) /* Save back chain and move SP */
- lis r0,RESET_VECTOR@h /* Address of reset vector */
- ori r0,r0, RESET_VECTOR@l
- stwu r1,-8(r1) /* Save back chain and move SP */
- stw r0,+12(r1) /* Save return addr (underflow vect) */
- sync
- bl early_sdram_init
- sync
-#endif /* CONFIG_440EP */
-
- /*
- * Copy SPL from cache into internal SRAM
- */
- li r4,(CFG_NAND_BOOT_SPL_SIZE >> 2) - 1
- mtctr r4
- lis r2,CFG_NAND_BOOT_SPL_SRC@h
- ori r2,r2,CFG_NAND_BOOT_SPL_SRC@l
- lis r3,CFG_NAND_BOOT_SPL_DST@h
- ori r3,r3,CFG_NAND_BOOT_SPL_DST@l
-spl_loop:
- lwzu r4,4(r2)
- stwu r4,4(r3)
- bdnz spl_loop
-
- /*
- * Jump to code in RAM
- */
- bl 00f
-00: mflr r10
- lis r3,(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)@h
- ori r3,r3,(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)@l
- sub r10,r10,r3
- addi r10,r10,28
- mtlr r10
- blr
-
-start_ram:
- sync
- isync
-#endif /* CONFIG_NAND_SPL */
-
bl 3f
b _start
stw r0,+12(r1) /* Save return addr (underflow vect) */
#ifdef CONFIG_NAND_SPL
- bl nand_boot /* will not return */
+ bl nand_boot_common /* will not return */
#else
GET_GOT
/* make sure above stores all comlete before going on */
sync
- /*----------------------------------------------------------------------- */
- /* Enable two 128MB cachable regions. */
- /*----------------------------------------------------------------------- */
- addis r1,r0,0xc000
- addi r1,r1,0x0001
- mticcr r1 /* instruction cache */
+ /* Set-up icache cacheability. */
+ lis r1, CFG_ICACHE_SACR_VALUE@h
+ ori r1, r1, CFG_ICACHE_SACR_VALUE@l
+ mticcr r1
+ isync
- addis r1,r0,0x0000
- addi r1,r1,0x0000
- mtdccr r1 /* data cache */
+ /* Set-up dcache cacheability. */
+ lis r1, CFG_DCACHE_SACR_VALUE@h
+ ori r1, r1, CFG_DCACHE_SACR_VALUE@l
+ mtdccr r1
addis r1,r0,CFG_INIT_RAM_ADDR@h
ori r1,r1,CFG_INIT_SP_OFFSET /* set up the stack to SDRAM */
/* dbsr is cleared by setting bits to 1) */
mtdbsr r4 /* clear/reset the dbsr */
- /*----------------------------------------------------------------------- */
- /* Invalidate I and D caches. Enable I cache for defined memory regions */
- /* to speed things up. Leave the D cache disabled for now. It will be */
- /* enabled/left disabled later based on user selected menu options. */
- /* Be aware that the I cache may be disabled later based on the menu */
- /* options as well. See miscLib/main.c. */
- /*----------------------------------------------------------------------- */
+ /* Invalidate the i- and d-caches. */
bl invalidate_icache
bl invalidate_dcache
- /*----------------------------------------------------------------------- */
- /* Enable two 128MB cachable regions. */
- /*----------------------------------------------------------------------- */
- lis r4,0xc000
- ori r4,r4,0x0001
- mticcr r4 /* instruction cache */
+ /* Set-up icache cacheability. */
+ lis r4, CFG_ICACHE_SACR_VALUE@h
+ ori r4, r4, CFG_ICACHE_SACR_VALUE@l
+ mticcr r4
isync
- lis r4,0x0000
- ori r4,r4,0x0000
- mtdccr r4 /* data cache */
+ /* Set-up dcache cacheability. */
+ lis r4, CFG_DCACHE_SACR_VALUE@h
+ ori r4, r4, CFG_DCACHE_SACR_VALUE@l
+ mtdccr r4
-#if !(defined(CFG_EBC_PB0AP) && defined(CFG_EBC_PB0CR)) || defined(CONFIG_405EX)
+#if !(defined(CFG_EBC_PB0AP) && defined(CFG_EBC_PB0CR))
/*----------------------------------------------------------------------- */
/* Tune the speed and size for flash CS0 */
/*----------------------------------------------------------------------- */
bl ext_bus_cntlr_init
#endif
+
#if !(defined(CFG_INIT_DCACHE_CS) || defined(CFG_TEMP_STACK_OCM))
/*
- * Boards like the Kilauea (405EX) don't have OCM and can't use
- * DCache for init-ram. So setup stack here directly after the
- * SDRAM is initialized.
+ * For boards that don't have OCM and can't use the data cache
+ * for their primordial stack, setup stack here directly after the
+ * SDRAM is initialized in ext_bus_cntlr_init.
*/
lis r1, CFG_INIT_RAM_ADDR@h
ori r1,r1,CFG_INIT_SP_OFFSET /* set up the stack in SDRAM */
#endif /* CONFIG_405EZ */
#endif
-#ifdef CONFIG_NAND_SPL
+ /*----------------------------------------------------------------------- */
+ /* Setup temporary stack in DCACHE or OCM if needed for SDRAM SPD. */
+ /*----------------------------------------------------------------------- */
+#ifdef CFG_INIT_DCACHE_CS
+ li r4, PBxAP
+ mtdcr ebccfga, r4
+ lis r4, CFG_INIT_DCACHE_PBxAR@h
+ ori r4, r4, CFG_INIT_DCACHE_PBxAR@l
+ mtdcr ebccfgd, r4
+
+ addi r4, 0, PBxCR
+ mtdcr ebccfga, r4
+ lis r4, CFG_INIT_DCACHE_PBxCR@h
+ ori r4, r4, CFG_INIT_DCACHE_PBxCR@l
+ mtdcr ebccfgd, r4
+
/*
- * Copy SPL from cache into internal SRAM
+ * Enable the data cache for the 128MB storage access control region
+ * at CFG_INIT_RAM_ADDR.
*/
- li r4,(CFG_NAND_BOOT_SPL_SIZE >> 2) - 1
- mtctr r4
- lis r2,CFG_NAND_BOOT_SPL_SRC@h
- ori r2,r2,CFG_NAND_BOOT_SPL_SRC@l
- lis r3,CFG_NAND_BOOT_SPL_DST@h
- ori r3,r3,CFG_NAND_BOOT_SPL_DST@l
-spl_loop:
- lwzu r4,4(r2)
- stwu r4,4(r3)
- bdnz spl_loop
+ mfdccr r4
+ oris r4, r4, PPC_128MB_SACR_VALUE(CFG_INIT_RAM_ADDR)@h
+ ori r4, r4, PPC_128MB_SACR_VALUE(CFG_INIT_RAM_ADDR)@l
+ mtdccr r4
/*
- * Jump to code in RAM
+ * Preallocate data cache lines to be used to avoid a subsequent
+ * cache miss and an ensuing machine check exception when exceptions
+ * are enabled.
*/
- bl 00f
-00: mflr r10
- lis r3,(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)@h
- ori r3,r3,(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)@l
- sub r10,r10,r3
- addi r10,r10,28
- mtlr r10
- blr
+ li r0, 0
-start_ram:
- sync
- isync
-#endif /* CONFIG_NAND_SPL */
+ lis r3, CFG_INIT_RAM_ADDR@h
+ ori r3, r3, CFG_INIT_RAM_ADDR@l
- /*----------------------------------------------------------------------- */
- /* Setup temporary stack in DCACHE or OCM if needed for SDRAM SPD. */
- /*----------------------------------------------------------------------- */
-#ifdef CFG_INIT_DCACHE_CS
- /*----------------------------------------------------------------------- */
- /* Memory Bank x (nothingness) initialization 1GB+64MEG */
- /* used as temporary stack pointer for stage0 */
- /*----------------------------------------------------------------------- */
- li r4,PBxAP
- mtdcr ebccfga,r4
- lis r4,0x0380
- ori r4,r4,0x0480
- mtdcr ebccfgd,r4
-
- addi r4,0,PBxCR
- mtdcr ebccfga,r4
- lis r4,0x400D
- ori r4,r4,0xa000
- mtdcr ebccfgd,r4
-
- /* turn on data cache for this region */
- lis r4,0x0080
- mtdccr r4
+ lis r4, CFG_INIT_RAM_END@h
+ ori r4, r4, CFG_INIT_RAM_END@l
+
+ /*
+ * Convert the size, in bytes, to the number of cache lines/blocks
+ * to preallocate.
+ */
+ clrlwi. r5, r4, (32 - L1_CACHE_SHIFT)
+ srwi r5, r4, L1_CACHE_SHIFT
+ beq ..load_counter
+ addi r5, r5, 0x0001
+..load_counter:
+ mtctr r5
- /* set stack pointer and clear stack to known value */
+ /* Preallocate the computed number of cache blocks. */
+..alloc_dcache_block:
+ dcba r0, r3
+ addi r3, r3, L1_CACHE_BYTES
+ bdnz ..alloc_dcache_block
+ sync
- lis r1,CFG_INIT_RAM_ADDR@h
- ori r1,r1,CFG_INIT_SP_OFFSET@l
+ /*
+ * Load the initial stack pointer and data area and convert the size,
+ * in bytes, to the number of words to initialize to a known value.
+ */
+ lis r1, CFG_INIT_RAM_ADDR@h
+ ori r1, r1, CFG_INIT_SP_OFFSET@l
- li r4,2048 /* we store 2048 words to stack */
+ lis r4, (CFG_INIT_RAM_END >> 2)@h
+ ori r4, r4, (CFG_INIT_RAM_END >> 2)@l
mtctr r4
- lis r2,CFG_INIT_RAM_ADDR@h /* we also clear data area */
- ori r2,r2,CFG_INIT_RAM_END@l /* so cant copy value from r1 */
+ lis r2, CFG_INIT_RAM_ADDR@h
+ ori r2, r2, CFG_INIT_RAM_END@l
- lis r4,0xdead /* we store 0xdeaddead in the stack */
- ori r4,r4,0xdead
+ lis r4, CFG_INIT_RAM_PATTERN@h
+ ori r4, r4, CFG_INIT_RAM_PATTERN@l
..stackloop:
- stwu r4,-4(r2)
+ stwu r4, -4(r2)
bdnz ..stackloop
- li r0, 0 /* Make room for stack frame header and */
- stwu r0, -4(r1) /* clear final stack frame so that */
- stwu r0, -4(r1) /* stack backtraces terminate cleanly */
+ /*
+ * Make room for stack frame header and clear final stack frame so
+ * that stack backtraces terminate cleanly.
+ */
+ stwu r0, -4(r1)
+ stwu r0, -4(r1)
+
/*
* Set up a dummy frame to store reset vector as return address.
* this causes stack underflow to reset board.
stw r0, +12(r1) /* Save return addr (underflow vect) */
#endif /* CFG_INIT_DCACHE_CS */
- /*----------------------------------------------------------------------- */
- /* Initialize SDRAM Controller */
- /*----------------------------------------------------------------------- */
- bl sdram_init
-
#ifdef CONFIG_NAND_SPL
- bl nand_boot /* will not return */
+ bl nand_boot_common /* will not return */
#else
GET_GOT /* initialize GOT access */
* This "function" does not return, instead it continues in RAM
* after relocating the monitor code.
*
- * r3 = dest
- * r4 = src
- * r5 = length in bytes
- * r6 = cachelinesize
+ * r3 = Relocated stack pointer
+ * r4 = Relocated global data pointer
+ * r5 = Relocated text pointer
*/
.globl relocate_code
relocate_code:
-#ifdef CONFIG_4xx_DCACHE
+#if defined(CONFIG_4xx_DCACHE) || defined(CFG_INIT_DCACHE_CS)
/*
- * We need to flush the Init Data before the dcache will be
- * invalidated
+ * We need to flush the initial global data (gd_t) before the dcache
+ * will be invalidated.
*/
- /* save regs */
- mr r9,r3
- mr r10,r4
- mr r11,r5
+ /* Save registers */
+ mr r9, r3
+ mr r10, r4
+ mr r11, r5
- mr r3,r4
- addi r4,r4,0x200 /* should be enough for init data */
+ /* Flush initial global data range */
+ mr r3, r4
+ addi r4, r4, CFG_GBL_DATA_SIZE@l
bl flush_dcache_range
- /* restore regs */
- mr r3,r9
- mr r4,r10
- mr r5,r11
-#endif
+#if defined(CFG_INIT_DCACHE_CS)
+ /*
+ * Undo the earlier data cache set-up for the primordial stack and
+ * data area. First, invalidate the data cache and then disable data
+ * cacheability for that area. Finally, restore the EBC values, if
+ * any.
+ */
+
+ /* Invalidate the primordial stack and data area in cache */
+ lis r3, CFG_INIT_RAM_ADDR@h
+ ori r3, r3, CFG_INIT_RAM_ADDR@l
+
+ lis r4, CFG_INIT_RAM_END@h
+ ori r4, r4, CFG_INIT_RAM_END@l
+ add r4, r4, r3
+
+ bl invalidate_dcache_range
+
+ /* Disable cacheability for the region */
+ mfdccr r3
+ lis r4, ~PPC_128MB_SACR_VALUE(CFG_INIT_RAM_ADDR)@h
+ ori r4, r4, ~PPC_128MB_SACR_VALUE(CFG_INIT_RAM_ADDR)@l
+ and r3, r3, r4
+ mtdccr r3
+
+ /* Restore the EBC parameters */
+ li r3, PBxAP
+ mtdcr ebccfga, r3
+ lis r3, PBxAP_VAL@h
+ ori r3, r3, PBxAP_VAL@l
+ mtdcr ebccfgd, r3
+
+ li r3, PBxCR
+ mtdcr ebccfga, r3
+ lis r3, PBxCR_VAL@h
+ ori r3, r3, PBxCR_VAL@l
+ mtdcr ebccfgd, r3
+#endif /* defined(CFG_INIT_DCACHE_CS) */
+
+ /* Restore registers */
+ mr r3, r9
+ mr r4, r10
+ mr r5, r11
+#endif /* defined(CONFIG_4xx_DCACHE) || defined(CFG_INIT_DCACHE_CS) */
#ifdef CFG_INIT_RAM_DCACHE
/*
addi r1,r0,CFG_TLB_FOR_BOOT_FLASH /* Use defined TLB */
#else
addi r1,r0,0x0000 /* Default TLB entry is #0 */
-#endif
+#endif /* CFG_TLB_FOR_BOOT_FLASH */
tlbre r0,r1,0x0002 /* Read contents */
ori r0,r0,0x0c00 /* Or in the inhibit, write through bit */
tlbwe r0,r1,0x0002 /* Save it out */
sync
isync
-#endif
+#endif /* defined(CONFIG_440EP) || ... || defined(CONFIG_460GT) */
mr r1, r3 /* Set new stack pointer */
mr r9, r4 /* Save copy of Init Data pointer */
mr r10, r5 /* Save copy of Destination Address */
/* First our own GOT */
add r14, r14, r15
- /* the the one used by the C code */
+ /* then the one used by the C code */
add r30, r30, r15
/*
blr
function_epilog(mftlb1)
#endif /* CONFIG_440 */
+
+#if defined(CONFIG_NAND_SPL)
+/*
+ * void nand_boot_relocate(dst, src, bytes)
+ *
+ * r3 = Destination address to copy code to (in SDRAM)
+ * r4 = Source address to copy code from
+ * r5 = size to copy in bytes
+ */
+nand_boot_relocate:
+ mr r6,r3
+ mr r7,r4
+ mflr r8
+
+ /*
+ * Copy SPL from icache into SDRAM
+ */
+ subi r3,r3,4
+ subi r4,r4,4
+ srwi r5,r5,2
+ mtctr r5
+..spl_loop:
+ lwzu r0,4(r4)
+ stwu r0,4(r3)
+ bdnz ..spl_loop
+
+ /*
+ * Calculate "corrected" link register, so that we "continue"
+ * in execution in destination range
+ */
+ sub r3,r7,r6 /* r3 = src - dst */
+ sub r8,r8,r3 /* r8 = link-reg - (src - dst) */
+ mtlr r8
+ blr
+
+nand_boot_common:
+ /*
+ * First initialize SDRAM. It has to be available *before* calling
+ * nand_boot().
+ */
+ lis r3,CFG_SDRAM_BASE@h
+ ori r3,r3,CFG_SDRAM_BASE@l
+ bl initdram
+
+ /*
+ * Now copy the 4k SPL code into SDRAM and continue execution
+ * from there.
+ */
+ lis r3,CFG_NAND_BOOT_SPL_DST@h
+ ori r3,r3,CFG_NAND_BOOT_SPL_DST@l
+ lis r4,CFG_NAND_BOOT_SPL_SRC@h
+ ori r4,r4,CFG_NAND_BOOT_SPL_SRC@l
+ lis r5,CFG_NAND_BOOT_SPL_SIZE@h
+ ori r5,r5,CFG_NAND_BOOT_SPL_SIZE@l
+ bl nand_boot_relocate
+
+ /*
+ * We're running from SDRAM now!!!
+ *
+ * It is necessary for 4xx systems to relocate from running at
+ * the original location (0xfffffxxx) to somewhere else (SDRAM
+ * preferably). This is because CS0 needs to be reconfigured for
+ * NAND access. And we can't reconfigure this CS when currently
+ * "running" from it.
+ */
+
+ /*
+ * Finally call nand_boot() to load main NAND U-Boot image from
+ * NAND and jump to it.
+ */
+ bl nand_boot /* will not return */
+#endif /* CONFIG_NAND_SPL */
val = get_esr();
-#if !defined(CONFIG_440)
+#if !defined(CONFIG_440) && !defined(CONFIG_405EX)
if (val& ESR_IMCP) {
printf("Instruction");
mtspr(ESR, val & ~ESR_IMCP);
}
printf(" machine check.\n");
-#elif defined(CONFIG_440)
+#elif defined(CONFIG_440) || defined(CONFIG_405EX)
if (val& ESR_IMCP){
printf("Instruction Synchronous Machine Check exception\n");
mtspr(SPRN_ESR, val & ~ESR_IMCP);
val = mfspr(MCSR);
if (val & MCSR_IB)
printf("Instruction Read PLB Error\n");
+#if defined(CONFIG_440)
if (val & MCSR_DRB)
printf("Data Read PLB Error\n");
if (val & MCSR_DWB)
printf("Data Write PLB Error\n");
+#else
+ if (val & MCSR_DB)
+ printf("Data PLB Error\n");
+#endif
if (val & MCSR_TLBP)
printf("TLB Parity Error\n");
if (val & MCSR_ICP){
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _PPC4xx_SDRAM_H_
+#define _PPC4xx_SDRAM_H_
+
+#if defined(CONFIG_SDRAM_PPC4xx_IBM_SDRAM)
+
+/*
+ * SDRAM Controller
+ */
+/*
+ * XXX - ToDo: Revisit file to change all these lower case defines into
+ * upper case. Also needs to be done in the controller setup code too
+ * of course. sr, 2008-06-02
+ */
+#ifndef CONFIG_405EP
+#define mem_besra 0x00 /* bus error syndrome reg a */
+#define mem_besrsa 0x04 /* bus error syndrome reg set a */
+#define mem_besrb 0x08 /* bus error syndrome reg b */
+#define mem_besrsb 0x0c /* bus error syndrome reg set b */
+#define mem_bear 0x10 /* bus error address reg */
+#endif
+#define mem_mcopt1 0x20 /* memory controller options 1 */
+#define mem_status 0x24 /* memory status */
+#define mem_rtr 0x30 /* refresh timer reg */
+#define mem_pmit 0x34 /* power management idle timer */
+#define mem_mb0cf 0x40 /* memory bank 0 configuration */
+#define mem_mb1cf 0x44 /* memory bank 1 configuration */
+#ifndef CONFIG_405EP
+#define mem_mb2cf 0x48 /* memory bank 2 configuration */
+#define mem_mb3cf 0x4c /* memory bank 3 configuration */
+#endif
+#define mem_sdtr1 0x80 /* timing reg 1 */
+#ifndef CONFIG_405EP
+#define mem_ecccf 0x94 /* ECC configuration */
+#define mem_eccerr 0x98 /* ECC error status */
+#endif
+
+#endif /* CONFIG_SDRAM_PPC4xx_IBM_SDRAM */
+
+#if defined(CONFIG_SDRAM_PPC4xx_IBM_DDR)
+
+/*
+ * Memory controller registers
+ */
+#define SDRAM_CFG0 0x20 /* memory controller options 0 */
+#define SDRAM_CFG1 0x21 /* memory controller options 1 */
+
+/*
+ * XXX - ToDo: Revisit file to change all these lower case defines into
+ * upper case. Also needs to be done in the controller setup code too
+ * of course. sr, 2008-06-02
+ */
+#define mem_besr0_clr 0x0000 /* bus error status reg 0 (clr) */
+#define mem_besr0_set 0x0004 /* bus error status reg 0 (set) */
+#define mem_besr1_clr 0x0008 /* bus error status reg 1 (clr) */
+#define mem_besr1_set 0x000c /* bus error status reg 1 (set) */
+#define mem_bear 0x0010 /* bus error address reg */
+#define mem_mirq_clr 0x0011 /* bus master interrupt (clr) */
+#define mem_mirq_set 0x0012 /* bus master interrupt (set) */
+#define mem_slio 0x0018 /* ddr sdram slave interface options */
+#define mem_cfg0 0x0020 /* ddr sdram options 0 */
+#define mem_cfg1 0x0021 /* ddr sdram options 1 */
+#define mem_devopt 0x0022 /* ddr sdram device options */
+#define mem_mcsts 0x0024 /* memory controller status */
+#define mem_rtr 0x0030 /* refresh timer register */
+#define mem_pmit 0x0034 /* power management idle timer */
+#define mem_uabba 0x0038 /* plb UABus base address */
+#define mem_b0cr 0x0040 /* ddr sdram bank 0 configuration */
+#define mem_b1cr 0x0044 /* ddr sdram bank 1 configuration */
+#define mem_b2cr 0x0048 /* ddr sdram bank 2 configuration */
+#define mem_b3cr 0x004c /* ddr sdram bank 3 configuration */
+#define mem_tr0 0x0080 /* sdram timing register 0 */
+#define mem_tr1 0x0081 /* sdram timing register 1 */
+#define mem_clktr 0x0082 /* ddr clock timing register */
+#define mem_wddctr 0x0083 /* write data/dm/dqs clock timing reg */
+#define mem_dlycal 0x0084 /* delay line calibration register */
+#define mem_eccesr 0x0098 /* ECC error status */
+
+/*
+ * Memory Controller Options 0
+ */
+#define SDRAM_CFG0_DCEN 0x80000000 /* SDRAM Controller Enable */
+#define SDRAM_CFG0_MCHK_MASK 0x30000000 /* Memory data errchecking mask */
+#define SDRAM_CFG0_MCHK_NON 0x00000000 /* No ECC generation */
+#define SDRAM_CFG0_MCHK_GEN 0x20000000 /* ECC generation */
+#define SDRAM_CFG0_MCHK_CHK 0x30000000 /* ECC generation and checking */
+#define SDRAM_CFG0_RDEN 0x08000000 /* Registered DIMM enable */
+#define SDRAM_CFG0_PMUD 0x04000000 /* Page management unit */
+#define SDRAM_CFG0_DMWD_MASK 0x02000000 /* DRAM width mask */
+#define SDRAM_CFG0_DMWD_32 0x00000000 /* 32 bits */
+#define SDRAM_CFG0_DMWD_64 0x02000000 /* 64 bits */
+#define SDRAM_CFG0_UIOS_MASK 0x00C00000 /* Unused IO State */
+#define SDRAM_CFG0_PDP 0x00200000 /* Page deallocation policy */
+
+/*
+ * Memory Controller Options 1
+ */
+#define SDRAM_CFG1_SRE 0x80000000 /* Self-Refresh Entry */
+#define SDRAM_CFG1_PMEN 0x40000000 /* Power Management Enable */
+
+/*
+ * SDRAM DEVPOT Options
+ */
+#define SDRAM_DEVOPT_DLL 0x80000000
+#define SDRAM_DEVOPT_DS 0x40000000
+
+/*
+ * SDRAM MCSTS Options
+ */
+#define SDRAM_MCSTS_MRSC 0x80000000
+#define SDRAM_MCSTS_SRMS 0x40000000
+#define SDRAM_MCSTS_CIS 0x20000000
+
+/*
+ * SDRAM Refresh Timer Register
+ */
+#define SDRAM_RTR_RINT_MASK 0xFFFF0000
+#define SDRAM_RTR_RINT_ENCODE(n) (((n) << 16) & SDRAM_RTR_RINT_MASK)
+
+/*
+ * SDRAM UABus Base Address Reg
+ */
+#define SDRAM_UABBA_UBBA_MASK 0x0000000F
+
+/*
+ * Memory Bank 0-7 configuration
+ */
+#define SDRAM_BXCR_SDBA_MASK 0xff800000 /* Base address */
+#define SDRAM_BXCR_SDSZ_MASK 0x000e0000 /* Size */
+#define SDRAM_BXCR_SDSZ_8 0x00020000 /* 8M */
+#define SDRAM_BXCR_SDSZ_16 0x00040000 /* 16M */
+#define SDRAM_BXCR_SDSZ_32 0x00060000 /* 32M */
+#define SDRAM_BXCR_SDSZ_64 0x00080000 /* 64M */
+#define SDRAM_BXCR_SDSZ_128 0x000a0000 /* 128M */
+#define SDRAM_BXCR_SDSZ_256 0x000c0000 /* 256M */
+#define SDRAM_BXCR_SDSZ_512 0x000e0000 /* 512M */
+#define SDRAM_BXCR_SDAM_MASK 0x0000e000 /* Addressing mode */
+#define SDRAM_BXCR_SDAM_1 0x00000000 /* Mode 1 */
+#define SDRAM_BXCR_SDAM_2 0x00002000 /* Mode 2 */
+#define SDRAM_BXCR_SDAM_3 0x00004000 /* Mode 3 */
+#define SDRAM_BXCR_SDAM_4 0x00006000 /* Mode 4 */
+#define SDRAM_BXCR_SDBE 0x00000001 /* Memory Bank Enable */
+
+/*
+ * SDRAM TR0 Options
+ */
+#define SDRAM_TR0_SDWR_MASK 0x80000000
+#define SDRAM_TR0_SDWR_2_CLK 0x00000000
+#define SDRAM_TR0_SDWR_3_CLK 0x80000000
+#define SDRAM_TR0_SDWD_MASK 0x40000000
+#define SDRAM_TR0_SDWD_0_CLK 0x00000000
+#define SDRAM_TR0_SDWD_1_CLK 0x40000000
+#define SDRAM_TR0_SDCL_MASK 0x01800000
+#define SDRAM_TR0_SDCL_2_0_CLK 0x00800000
+#define SDRAM_TR0_SDCL_2_5_CLK 0x01000000
+#define SDRAM_TR0_SDCL_3_0_CLK 0x01800000
+#define SDRAM_TR0_SDPA_MASK 0x000C0000
+#define SDRAM_TR0_SDPA_2_CLK 0x00040000
+#define SDRAM_TR0_SDPA_3_CLK 0x00080000
+#define SDRAM_TR0_SDPA_4_CLK 0x000C0000
+#define SDRAM_TR0_SDCP_MASK 0x00030000
+#define SDRAM_TR0_SDCP_2_CLK 0x00000000
+#define SDRAM_TR0_SDCP_3_CLK 0x00010000
+#define SDRAM_TR0_SDCP_4_CLK 0x00020000
+#define SDRAM_TR0_SDCP_5_CLK 0x00030000
+#define SDRAM_TR0_SDLD_MASK 0x0000C000
+#define SDRAM_TR0_SDLD_1_CLK 0x00000000
+#define SDRAM_TR0_SDLD_2_CLK 0x00004000
+#define SDRAM_TR0_SDRA_MASK 0x0000001C
+#define SDRAM_TR0_SDRA_6_CLK 0x00000000
+#define SDRAM_TR0_SDRA_7_CLK 0x00000004
+#define SDRAM_TR0_SDRA_8_CLK 0x00000008
+#define SDRAM_TR0_SDRA_9_CLK 0x0000000C
+#define SDRAM_TR0_SDRA_10_CLK 0x00000010
+#define SDRAM_TR0_SDRA_11_CLK 0x00000014
+#define SDRAM_TR0_SDRA_12_CLK 0x00000018
+#define SDRAM_TR0_SDRA_13_CLK 0x0000001C
+#define SDRAM_TR0_SDRD_MASK 0x00000003
+#define SDRAM_TR0_SDRD_2_CLK 0x00000001
+#define SDRAM_TR0_SDRD_3_CLK 0x00000002
+#define SDRAM_TR0_SDRD_4_CLK 0x00000003
+
+/*
+ * SDRAM TR1 Options
+ */
+#define SDRAM_TR1_RDSS_MASK 0xC0000000
+#define SDRAM_TR1_RDSS_TR0 0x00000000
+#define SDRAM_TR1_RDSS_TR1 0x40000000
+#define SDRAM_TR1_RDSS_TR2 0x80000000
+#define SDRAM_TR1_RDSS_TR3 0xC0000000
+#define SDRAM_TR1_RDSL_MASK 0x00C00000
+#define SDRAM_TR1_RDSL_STAGE1 0x00000000
+#define SDRAM_TR1_RDSL_STAGE2 0x00400000
+#define SDRAM_TR1_RDSL_STAGE3 0x00800000
+#define SDRAM_TR1_RDCD_MASK 0x00000800
+#define SDRAM_TR1_RDCD_RCD_0_0 0x00000000
+#define SDRAM_TR1_RDCD_RCD_1_2 0x00000800
+#define SDRAM_TR1_RDCT_MASK 0x000001FF
+#define SDRAM_TR1_RDCT_ENCODE(x) (((x) << 0) & SDRAM_TR1_RDCT_MASK)
+#define SDRAM_TR1_RDCT_DECODE(x) (((x) & SDRAM_TR1_RDCT_MASK) >> 0)
+#define SDRAM_TR1_RDCT_MIN 0x00000000
+#define SDRAM_TR1_RDCT_MAX 0x000001FF
+
+/*
+ * SDRAM WDDCTR Options
+ */
+#define SDRAM_WDDCTR_WRCP_MASK 0xC0000000
+#define SDRAM_WDDCTR_WRCP_0DEG 0x00000000
+#define SDRAM_WDDCTR_WRCP_90DEG 0x40000000
+#define SDRAM_WDDCTR_WRCP_180DEG 0x80000000
+#define SDRAM_WDDCTR_DCD_MASK 0x000001FF
+
+/*
+ * SDRAM CLKTR Options
+ */
+#define SDRAM_CLKTR_CLKP_MASK 0xC0000000
+#define SDRAM_CLKTR_CLKP_0DEG 0x00000000
+#define SDRAM_CLKTR_CLKP_90DEG 0x40000000
+#define SDRAM_CLKTR_CLKP_180DEG 0x80000000
+#define SDRAM_CLKTR_DCDT_MASK 0x000001FF
+
+/*
+ * SDRAM DLYCAL Options
+ */
+#define SDRAM_DLYCAL_DLCV_MASK 0x000003FC
+#define SDRAM_DLYCAL_DLCV_ENCODE(x) (((x)<<2) & SDRAM_DLYCAL_DLCV_MASK)
+#define SDRAM_DLYCAL_DLCV_DECODE(x) (((x) & SDRAM_DLYCAL_DLCV_MASK)>>2)
+
+#endif /* CONFIG_SDRAM_PPC4xx_IBM_DDR */
+
+#if defined(CONFIG_SDRAM_PPC4xx_IBM_DDR2)
+
+#define SDRAM_DLYCAL_DLCV_MASK 0x000003FC
+#define SDRAM_DLYCAL_DLCV_ENCODE(x) (((x)<<2) & SDRAM_DLYCAL_DLCV_MASK)
+#define SDRAM_DLYCAL_DLCV_DECODE(x) (((x) & SDRAM_DLYCAL_DLCV_MASK)>>2)
+
+/*
+ * Memory queue defines
+ */
+#define SDRAMQ_DCR_BASE 0x040
+
+#define SDRAM_R0BAS (SDRAMQ_DCR_BASE+0x0) /* rank 0 base address & size */
+#define SDRAM_R1BAS (SDRAMQ_DCR_BASE+0x1) /* rank 1 base address & size */
+#define SDRAM_R2BAS (SDRAMQ_DCR_BASE+0x2) /* rank 2 base address & size */
+#define SDRAM_R3BAS (SDRAMQ_DCR_BASE+0x3) /* rank 3 base address & size */
+#define SDRAM_CONF1HB (SDRAMQ_DCR_BASE+0x5) /* configuration 1 HB */
+#define SDRAM_ERRSTATHB (SDRAMQ_DCR_BASE+0x7) /* error status HB */
+#define SDRAM_ERRADDUHB (SDRAMQ_DCR_BASE+0x8) /* error address upper 32 HB */
+#define SDRAM_ERRADDLHB (SDRAMQ_DCR_BASE+0x9) /* error address lower 32 HB */
+#define SDRAM_PLBADDULL (SDRAMQ_DCR_BASE+0xA) /* PLB base address upper 32 LL */
+#define SDRAM_CONF1LL (SDRAMQ_DCR_BASE+0xB) /* configuration 1 LL */
+#define SDRAM_ERRSTATLL (SDRAMQ_DCR_BASE+0xC) /* error status LL */
+#define SDRAM_ERRADDULL (SDRAMQ_DCR_BASE+0xD) /* error address upper 32 LL */
+#define SDRAM_ERRADDLLL (SDRAMQ_DCR_BASE+0xE) /* error address lower 32 LL */
+#define SDRAM_CONFPATHB (SDRAMQ_DCR_BASE+0xF) /* configuration between paths */
+#define SDRAM_PLBADDUHB (SDRAMQ_DCR_BASE+0x10) /* PLB base address upper 32 LL */
+
+#if !defined(CONFIG_405EX)
+/*
+ * Memory Bank 0-7 configuration
+ */
+#if defined(CONFIG_440SPE) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT)
+#define SDRAM_RXBAS_SDBA_MASK 0xFFE00000 /* Base address */
+#define SDRAM_RXBAS_SDBA_ENCODE(n) ((((u32)(n))&0xFFE00000)>>2)
+#define SDRAM_RXBAS_SDBA_DECODE(n) ((((u32)(n))&0xFFE00000)<<2)
+#endif /* CONFIG_440SPE */
+#if defined(CONFIG_440SP)
+#define SDRAM_RXBAS_SDBA_MASK 0xFF800000 /* Base address */
+#define SDRAM_RXBAS_SDBA_ENCODE(n) ((((u32)(n))&0xFF800000))
+#define SDRAM_RXBAS_SDBA_DECODE(n) ((((u32)(n))&0xFF800000))
+#endif /* CONFIG_440SP */
+#define SDRAM_RXBAS_SDSZ_MASK 0x0000FFC0 /* Size */
+#define SDRAM_RXBAS_SDSZ_ENCODE(n) ((((u32)(n))&0x3FF)<<6)
+#define SDRAM_RXBAS_SDSZ_DECODE(n) ((((u32)(n))>>6)&0x3FF)
+#define SDRAM_RXBAS_SDSZ_0 0x00000000 /* 0M */
+#define SDRAM_RXBAS_SDSZ_8 0x0000FFC0 /* 8M */
+#define SDRAM_RXBAS_SDSZ_16 0x0000FF80 /* 16M */
+#define SDRAM_RXBAS_SDSZ_32 0x0000FF00 /* 32M */
+#define SDRAM_RXBAS_SDSZ_64 0x0000FE00 /* 64M */
+#define SDRAM_RXBAS_SDSZ_128 0x0000FC00 /* 128M */
+#define SDRAM_RXBAS_SDSZ_256 0x0000F800 /* 256M */
+#define SDRAM_RXBAS_SDSZ_512 0x0000F000 /* 512M */
+#define SDRAM_RXBAS_SDSZ_1024 0x0000E000 /* 1024M */
+#define SDRAM_RXBAS_SDSZ_2048 0x0000C000 /* 2048M */
+#define SDRAM_RXBAS_SDSZ_4096 0x00008000 /* 4096M */
+#else /* CONFIG_405EX */
+/*
+ * XXX - ToDo:
+ * Revisit this file to check if all these 405EX defines are correct and
+ * can be used in the common 44x_spd_ddr2 code as well. sr, 2008-06-02
+ */
+#define SDRAM_RXBAS_SDSZ_MASK PPC_REG_VAL(19, 0xF)
+#define SDRAM_RXBAS_SDSZ_4MB PPC_REG_VAL(19, 0x0)
+#define SDRAM_RXBAS_SDSZ_8MB PPC_REG_VAL(19, 0x1)
+#define SDRAM_RXBAS_SDSZ_16MB PPC_REG_VAL(19, 0x2)
+#define SDRAM_RXBAS_SDSZ_32MB PPC_REG_VAL(19, 0x3)
+#define SDRAM_RXBAS_SDSZ_64MB PPC_REG_VAL(19, 0x4)
+#define SDRAM_RXBAS_SDSZ_128MB PPC_REG_VAL(19, 0x5)
+#define SDRAM_RXBAS_SDSZ_256MB PPC_REG_VAL(19, 0x6)
+#define SDRAM_RXBAS_SDSZ_512MB PPC_REG_VAL(19, 0x7)
+#define SDRAM_RXBAS_SDSZ_1024MB PPC_REG_VAL(19, 0x8)
+#define SDRAM_RXBAS_SDSZ_2048MB PPC_REG_VAL(19, 0x9)
+#define SDRAM_RXBAS_SDSZ_4096MB PPC_REG_VAL(19, 0xA)
+#define SDRAM_RXBAS_SDSZ_8192MB PPC_REG_VAL(19, 0xB)
+#define SDRAM_RXBAS_SDSZ_8 SDRAM_RXBAS_SDSZ_8MB
+#define SDRAM_RXBAS_SDSZ_16 SDRAM_RXBAS_SDSZ_16MB
+#define SDRAM_RXBAS_SDSZ_32 SDRAM_RXBAS_SDSZ_32MB
+#define SDRAM_RXBAS_SDSZ_64 SDRAM_RXBAS_SDSZ_64MB
+#define SDRAM_RXBAS_SDSZ_128 SDRAM_RXBAS_SDSZ_128MB
+#define SDRAM_RXBAS_SDSZ_256 SDRAM_RXBAS_SDSZ_256MB
+#define SDRAM_RXBAS_SDSZ_512 SDRAM_RXBAS_SDSZ_512MB
+#define SDRAM_RXBAS_SDSZ_1024 SDRAM_RXBAS_SDSZ_1024MB
+#define SDRAM_RXBAS_SDSZ_2048 SDRAM_RXBAS_SDSZ_2048MB
+#define SDRAM_RXBAS_SDSZ_4096 SDRAM_RXBAS_SDSZ_4096MB
+#define SDRAM_RXBAS_SDSZ_8192 SDRAM_RXBAS_SDSZ_8192MB
+#define SDRAM_RXBAS_SDAM_MODE0 PPC_REG_VAL(23, 0x0)
+#define SDRAM_RXBAS_SDAM_MODE1 PPC_REG_VAL(23, 0x1)
+#define SDRAM_RXBAS_SDAM_MODE2 PPC_REG_VAL(23, 0x2)
+#define SDRAM_RXBAS_SDAM_MODE3 PPC_REG_VAL(23, 0x3)
+#define SDRAM_RXBAS_SDAM_MODE4 PPC_REG_VAL(23, 0x4)
+#define SDRAM_RXBAS_SDAM_MODE5 PPC_REG_VAL(23, 0x5)
+#define SDRAM_RXBAS_SDAM_MODE6 PPC_REG_VAL(23, 0x6)
+#define SDRAM_RXBAS_SDAM_MODE7 PPC_REG_VAL(23, 0x7)
+#define SDRAM_RXBAS_SDAM_MODE8 PPC_REG_VAL(23, 0x8)
+#define SDRAM_RXBAS_SDAM_MODE9 PPC_REG_VAL(23, 0x9)
+#define SDRAM_RXBAS_SDBE_DISABLE PPC_REG_VAL(31, 0x0)
+#define SDRAM_RXBAS_SDBE_ENABLE PPC_REG_VAL(31, 0x1)
+#endif /* CONFIG_405EX */
+
+/*
+ * Memory controller registers
+ */
+#define SDRAM_MCSTAT 0x14 /* memory controller status */
+#define SDRAM_MCOPT1 0x20 /* memory controller options 1 */
+#define SDRAM_MCOPT2 0x21 /* memory controller options 2 */
+#define SDRAM_MODT0 0x22 /* on die termination for bank 0 */
+#define SDRAM_MODT1 0x23 /* on die termination for bank 1 */
+#define SDRAM_MODT2 0x24 /* on die termination for bank 2 */
+#define SDRAM_MODT3 0x25 /* on die termination for bank 3 */
+#define SDRAM_CODT 0x26 /* on die termination for controller */
+#define SDRAM_VVPR 0x27 /* variable VRef programmming */
+#define SDRAM_OPARS 0x28 /* on chip driver control setup */
+#define SDRAM_OPART 0x29 /* on chip driver control trigger */
+#define SDRAM_RTR 0x30 /* refresh timer */
+#define SDRAM_PMIT 0x34 /* power management idle timer */
+#define SDRAM_MB0CF 0x40 /* memory bank 0 configuration */
+#define SDRAM_MB1CF 0x44 /* memory bank 1 configuration */
+#define SDRAM_MB2CF 0x48
+#define SDRAM_MB3CF 0x4C
+#define SDRAM_INITPLR0 0x50 /* manual initialization control */
+#define SDRAM_INITPLR1 0x51 /* manual initialization control */
+#define SDRAM_INITPLR2 0x52 /* manual initialization control */
+#define SDRAM_INITPLR3 0x53 /* manual initialization control */
+#define SDRAM_INITPLR4 0x54 /* manual initialization control */
+#define SDRAM_INITPLR5 0x55 /* manual initialization control */
+#define SDRAM_INITPLR6 0x56 /* manual initialization control */
+#define SDRAM_INITPLR7 0x57 /* manual initialization control */
+#define SDRAM_INITPLR8 0x58 /* manual initialization control */
+#define SDRAM_INITPLR9 0x59 /* manual initialization control */
+#define SDRAM_INITPLR10 0x5a /* manual initialization control */
+#define SDRAM_INITPLR11 0x5b /* manual initialization control */
+#define SDRAM_INITPLR12 0x5c /* manual initialization control */
+#define SDRAM_INITPLR13 0x5d /* manual initialization control */
+#define SDRAM_INITPLR14 0x5e /* manual initialization control */
+#define SDRAM_INITPLR15 0x5f /* manual initialization control */
+#define SDRAM_RQDC 0x70 /* read DQS delay control */
+#define SDRAM_RFDC 0x74 /* read feedback delay control */
+#define SDRAM_RDCC 0x78 /* read data capture control */
+#define SDRAM_DLCR 0x7A /* delay line calibration */
+#define SDRAM_CLKTR 0x80 /* DDR clock timing */
+#define SDRAM_WRDTR 0x81 /* write data, DQS, DM clock, timing */
+#define SDRAM_SDTR1 0x85 /* DDR SDRAM timing 1 */
+#define SDRAM_SDTR2 0x86 /* DDR SDRAM timing 2 */
+#define SDRAM_SDTR3 0x87 /* DDR SDRAM timing 3 */
+#define SDRAM_MMODE 0x88 /* memory mode */
+#define SDRAM_MEMODE 0x89 /* memory extended mode */
+#define SDRAM_ECCCR 0x98 /* ECC error status */
+#define SDRAM_CID 0xA4 /* core ID */
+#define SDRAM_RID 0xA8 /* revision ID */
+#define SDRAM_RTSR 0xB1 /* run time status tracking */
+
+/*
+ * Memory Controller Status
+ */
+#define SDRAM_MCSTAT_MIC_MASK 0x80000000 /* Memory init status mask */
+#define SDRAM_MCSTAT_MIC_NOTCOMP 0x00000000 /* Mem init not complete */
+#define SDRAM_MCSTAT_MIC_COMP 0x80000000 /* Mem init complete */
+#define SDRAM_MCSTAT_SRMS_MASK 0x40000000 /* Mem self refresh stat mask */
+#define SDRAM_MCSTAT_SRMS_NOT_SF 0x00000000 /* Mem not in self refresh */
+#define SDRAM_MCSTAT_SRMS_SF 0x40000000 /* Mem in self refresh */
+#define SDRAM_MCSTAT_IDLE_MASK 0x20000000 /* Mem self refresh stat mask */
+#define SDRAM_MCSTAT_IDLE_NOT 0x00000000 /* Mem contr not idle */
+#define SDRAM_MCSTAT_IDLE 0x20000000 /* Mem contr idle */
+
+/*
+ * Memory Controller Options 1
+ */
+#define SDRAM_MCOPT1_MCHK_MASK 0x30000000 /* Memory data err check mask*/
+#define SDRAM_MCOPT1_MCHK_NON 0x00000000 /* No ECC generation */
+#define SDRAM_MCOPT1_MCHK_GEN 0x20000000 /* ECC generation */
+#define SDRAM_MCOPT1_MCHK_CHK 0x10000000 /* ECC generation and check */
+#define SDRAM_MCOPT1_MCHK_CHK_REP 0x30000000 /* ECC generation, chk, report*/
+#define SDRAM_MCOPT1_MCHK_CHK_DECODE(n) ((((u32)(n))>>28)&0x3)
+#define SDRAM_MCOPT1_RDEN_MASK 0x08000000 /* Registered DIMM mask */
+#define SDRAM_MCOPT1_RDEN 0x08000000 /* Registered DIMM enable */
+#define SDRAM_MCOPT1_PMU_MASK 0x06000000 /* Page management unit mask */
+#define SDRAM_MCOPT1_PMU_CLOSE 0x00000000 /* PMU Close */
+#define SDRAM_MCOPT1_PMU_OPEN 0x04000000 /* PMU Open */
+#define SDRAM_MCOPT1_PMU_AUTOCLOSE 0x02000000 /* PMU AutoClose */
+#define SDRAM_MCOPT1_DMWD_MASK 0x01000000 /* DRAM width mask */
+#define SDRAM_MCOPT1_DMWD_32 0x00000000 /* 32 bits */
+#define SDRAM_MCOPT1_DMWD_64 0x01000000 /* 64 bits */
+#define SDRAM_MCOPT1_UIOS_MASK 0x00C00000 /* Unused IO State */
+#define SDRAM_MCOPT1_BCNT_MASK 0x00200000 /* Bank count */
+#define SDRAM_MCOPT1_4_BANKS 0x00000000 /* 4 Banks */
+#define SDRAM_MCOPT1_8_BANKS 0x00200000 /* 8 Banks */
+#define SDRAM_MCOPT1_DDR_TYPE_MASK 0x00100000 /* DDR Memory Type mask */
+#define SDRAM_MCOPT1_DDR1_TYPE 0x00000000 /* DDR1 Memory Type */
+#define SDRAM_MCOPT1_DDR2_TYPE 0x00100000 /* DDR2 Memory Type */
+#define SDRAM_MCOPT1_QDEP 0x00020000 /* 4 commands deep */
+#define SDRAM_MCOPT1_RWOO_MASK 0x00008000 /* Out of Order Read mask */
+#define SDRAM_MCOPT1_RWOO_DISABLED 0x00000000 /* disabled */
+#define SDRAM_MCOPT1_RWOO_ENABLED 0x00008000 /* enabled */
+#define SDRAM_MCOPT1_WOOO_MASK 0x00004000 /* Out of Order Write mask */
+#define SDRAM_MCOPT1_WOOO_DISABLED 0x00000000 /* disabled */
+#define SDRAM_MCOPT1_WOOO_ENABLED 0x00004000 /* enabled */
+#define SDRAM_MCOPT1_DCOO_MASK 0x00002000 /* All Out of Order mask */
+#define SDRAM_MCOPT1_DCOO_DISABLED 0x00002000 /* disabled */
+#define SDRAM_MCOPT1_DCOO_ENABLED 0x00000000 /* enabled */
+#define SDRAM_MCOPT1_DREF_MASK 0x00001000 /* Deferred refresh mask */
+#define SDRAM_MCOPT1_DREF_NORMAL 0x00000000 /* normal refresh */
+#define SDRAM_MCOPT1_DREF_DEFER_4 0x00001000 /* defer up to 4 refresh cmd */
+
+/*
+ * Memory Controller Options 2
+ */
+#define SDRAM_MCOPT2_SREN_MASK 0x80000000 /* Self Test mask */
+#define SDRAM_MCOPT2_SREN_EXIT 0x00000000 /* Self Test exit */
+#define SDRAM_MCOPT2_SREN_ENTER 0x80000000 /* Self Test enter */
+#define SDRAM_MCOPT2_PMEN_MASK 0x40000000 /* Power Management mask */
+#define SDRAM_MCOPT2_PMEN_DISABLE 0x00000000 /* disable */
+#define SDRAM_MCOPT2_PMEN_ENABLE 0x40000000 /* enable */
+#define SDRAM_MCOPT2_IPTR_MASK 0x20000000 /* Init Trigger Reg mask */
+#define SDRAM_MCOPT2_IPTR_IDLE 0x00000000 /* idle */
+#define SDRAM_MCOPT2_IPTR_EXECUTE 0x20000000 /* execute preloaded init */
+#define SDRAM_MCOPT2_XSRP_MASK 0x10000000 /* Exit Self Refresh Prevent */
+#define SDRAM_MCOPT2_XSRP_ALLOW 0x00000000 /* allow self refresh exit */
+#define SDRAM_MCOPT2_XSRP_PREVENT 0x10000000 /* prevent self refresh exit */
+#define SDRAM_MCOPT2_DCEN_MASK 0x08000000 /* SDRAM Controller Enable */
+#define SDRAM_MCOPT2_DCEN_DISABLE 0x00000000 /* SDRAM Controller Enable */
+#define SDRAM_MCOPT2_DCEN_ENABLE 0x08000000 /* SDRAM Controller Enable */
+#define SDRAM_MCOPT2_ISIE_MASK 0x04000000 /* Init Seq Interruptable mas*/
+#define SDRAM_MCOPT2_ISIE_DISABLE 0x00000000 /* disable */
+#define SDRAM_MCOPT2_ISIE_ENABLE 0x04000000 /* enable */
+
+/*
+ * SDRAM Refresh Timer Register
+ */
+#define SDRAM_RTR_RINT_MASK 0xFFF80000
+#define SDRAM_RTR_RINT_ENCODE(n) ((((u32)(n))&0xFFF8)<<16)
+#define SDRAM_RTR_RINT_DECODE(n) ((((u32)(n))>>16)&0xFFF8)
+
+/*
+ * SDRAM Read DQS Delay Control Register
+ */
+#define SDRAM_RQDC_RQDE_MASK 0x80000000
+#define SDRAM_RQDC_RQDE_DISABLE 0x00000000
+#define SDRAM_RQDC_RQDE_ENABLE 0x80000000
+#define SDRAM_RQDC_RQFD_MASK 0x000001FF
+#define SDRAM_RQDC_RQFD_ENCODE(n) ((((u32)(n))&0x1FF)<<0)
+
+#define SDRAM_RQDC_RQFD_MAX 0x1FF
+
+/*
+ * SDRAM Read Data Capture Control Register
+ */
+#define SDRAM_RDCC_RDSS_MASK 0xC0000000
+#define SDRAM_RDCC_RDSS_T1 0x00000000
+#define SDRAM_RDCC_RDSS_T2 0x40000000
+#define SDRAM_RDCC_RDSS_T3 0x80000000
+#define SDRAM_RDCC_RDSS_T4 0xC0000000
+#define SDRAM_RDCC_RSAE_MASK 0x00000001
+#define SDRAM_RDCC_RSAE_DISABLE 0x00000001
+#define SDRAM_RDCC_RSAE_ENABLE 0x00000000
+
+/*
+ * SDRAM Read Feedback Delay Control Register
+ */
+#define SDRAM_RFDC_ARSE_MASK 0x80000000
+#define SDRAM_RFDC_ARSE_DISABLE 0x80000000
+#define SDRAM_RFDC_ARSE_ENABLE 0x00000000
+#define SDRAM_RFDC_RFOS_MASK 0x007F0000
+#define SDRAM_RFDC_RFOS_ENCODE(n) ((((u32)(n))&0x7F)<<16)
+#define SDRAM_RFDC_RFFD_MASK 0x000007FF
+#define SDRAM_RFDC_RFFD_ENCODE(n) ((((u32)(n))&0x7FF)<<0)
+
+#define SDRAM_RFDC_RFFD_MAX 0x7FF
+
+/*
+ * SDRAM Delay Line Calibration Register
+ */
+#define SDRAM_DLCR_DCLM_MASK 0x80000000
+#define SDRAM_DLCR_DCLM_MANUEL 0x80000000
+#define SDRAM_DLCR_DCLM_AUTO 0x00000000
+#define SDRAM_DLCR_DLCR_MASK 0x08000000
+#define SDRAM_DLCR_DLCR_CALIBRATE 0x08000000
+#define SDRAM_DLCR_DLCR_IDLE 0x00000000
+#define SDRAM_DLCR_DLCS_MASK 0x07000000
+#define SDRAM_DLCR_DLCS_NOT_RUN 0x00000000
+#define SDRAM_DLCR_DLCS_IN_PROGRESS 0x01000000
+#define SDRAM_DLCR_DLCS_COMPLETE 0x02000000
+#define SDRAM_DLCR_DLCS_CONT_DONE 0x03000000
+#define SDRAM_DLCR_DLCS_ERROR 0x04000000
+#define SDRAM_DLCR_DLCV_MASK 0x000001FF
+#define SDRAM_DLCR_DLCV_ENCODE(n) ((((u32)(n))&0x1FF)<<0)
+#define SDRAM_DLCR_DLCV_DECODE(n) ((((u32)(n))>>0)&0x1FF)
+
+/*
+ * SDRAM Controller On Die Termination Register
+ */
+#define SDRAM_CODT_ODT_ON 0x80000000
+#define SDRAM_CODT_ODT_OFF 0x00000000
+#define SDRAM_CODT_DQS_VOLTAGE_DDR_MASK 0x00000020
+#define SDRAM_CODT_DQS_2_5_V_DDR1 0x00000000
+#define SDRAM_CODT_DQS_1_8_V_DDR2 0x00000020
+#define SDRAM_CODT_DQS_MASK 0x00000010
+#define SDRAM_CODT_DQS_DIFFERENTIAL 0x00000000
+#define SDRAM_CODT_DQS_SINGLE_END 0x00000010
+#define SDRAM_CODT_CKSE_DIFFERENTIAL 0x00000000
+#define SDRAM_CODT_CKSE_SINGLE_END 0x00000008
+#define SDRAM_CODT_FEEBBACK_RCV_SINGLE_END 0x00000004
+#define SDRAM_CODT_FEEBBACK_DRV_SINGLE_END 0x00000002
+#define SDRAM_CODT_IO_HIZ 0x00000000
+#define SDRAM_CODT_IO_NMODE 0x00000001
+
+/*
+ * SDRAM Mode Register
+ */
+#define SDRAM_MMODE_WR_MASK 0x00000E00
+#define SDRAM_MMODE_WR_DDR1 0x00000000
+#define SDRAM_MMODE_WR_DDR2_3_CYC 0x00000400
+#define SDRAM_MMODE_WR_DDR2_4_CYC 0x00000600
+#define SDRAM_MMODE_WR_DDR2_5_CYC 0x00000800
+#define SDRAM_MMODE_WR_DDR2_6_CYC 0x00000A00
+#define SDRAM_MMODE_DCL_MASK 0x00000070
+#define SDRAM_MMODE_DCL_DDR1_2_0_CLK 0x00000020
+#define SDRAM_MMODE_DCL_DDR1_2_5_CLK 0x00000060
+#define SDRAM_MMODE_DCL_DDR1_3_0_CLK 0x00000030
+#define SDRAM_MMODE_DCL_DDR2_2_0_CLK 0x00000020
+#define SDRAM_MMODE_DCL_DDR2_3_0_CLK 0x00000030
+#define SDRAM_MMODE_DCL_DDR2_4_0_CLK 0x00000040
+#define SDRAM_MMODE_DCL_DDR2_5_0_CLK 0x00000050
+#define SDRAM_MMODE_DCL_DDR2_6_0_CLK 0x00000060
+#define SDRAM_MMODE_DCL_DDR2_7_0_CLK 0x00000070
+
+/*
+ * SDRAM Extended Mode Register
+ */
+#define SDRAM_MEMODE_DIC_MASK 0x00000002
+#define SDRAM_MEMODE_DIC_NORMAL 0x00000000
+#define SDRAM_MEMODE_DIC_WEAK 0x00000002
+#define SDRAM_MEMODE_DLL_MASK 0x00000001
+#define SDRAM_MEMODE_DLL_DISABLE 0x00000001
+#define SDRAM_MEMODE_DLL_ENABLE 0x00000000
+#define SDRAM_MEMODE_RTT_MASK 0x00000044
+#define SDRAM_MEMODE_RTT_DISABLED 0x00000000
+#define SDRAM_MEMODE_RTT_75OHM 0x00000004
+#define SDRAM_MEMODE_RTT_150OHM 0x00000040
+#define SDRAM_MEMODE_DQS_MASK 0x00000400
+#define SDRAM_MEMODE_DQS_DISABLE 0x00000400
+#define SDRAM_MEMODE_DQS_ENABLE 0x00000000
+
+/*
+ * SDRAM Clock Timing Register
+ */
+#define SDRAM_CLKTR_CLKP_MASK 0xC0000000
+#define SDRAM_CLKTR_CLKP_0_DEG 0x00000000
+#define SDRAM_CLKTR_CLKP_180_DEG_ADV 0x80000000
+#define SDRAM_CLKTR_CLKP_90_DEG_ADV 0x40000000
+#define SDRAM_CLKTR_CLKP_270_DEG_ADV 0xC0000000
+
+/*
+ * SDRAM Write Timing Register
+ */
+#define SDRAM_WRDTR_LLWP_MASK 0x10000000
+#define SDRAM_WRDTR_LLWP_DIS 0x10000000
+#define SDRAM_WRDTR_LLWP_1_CYC 0x00000000
+#define SDRAM_WRDTR_WTR_MASK 0x0E000000
+#define SDRAM_WRDTR_WTR_0_DEG 0x06000000
+#define SDRAM_WRDTR_WTR_90_DEG_ADV 0x04000000
+#define SDRAM_WRDTR_WTR_180_DEG_ADV 0x02000000
+#define SDRAM_WRDTR_WTR_270_DEG_ADV 0x00000000
+
+/*
+ * SDRAM SDTR1 Options
+ */
+#define SDRAM_SDTR1_LDOF_MASK 0x80000000
+#define SDRAM_SDTR1_LDOF_1_CLK 0x00000000
+#define SDRAM_SDTR1_LDOF_2_CLK 0x80000000
+#define SDRAM_SDTR1_RTW_MASK 0x00F00000
+#define SDRAM_SDTR1_RTW_2_CLK 0x00200000
+#define SDRAM_SDTR1_RTW_3_CLK 0x00300000
+#define SDRAM_SDTR1_WTWO_MASK 0x000F0000
+#define SDRAM_SDTR1_WTWO_0_CLK 0x00000000
+#define SDRAM_SDTR1_WTWO_1_CLK 0x00010000
+#define SDRAM_SDTR1_RTRO_MASK 0x0000F000
+#define SDRAM_SDTR1_RTRO_1_CLK 0x00001000
+#define SDRAM_SDTR1_RTRO_2_CLK 0x00002000
+
+/*
+ * SDRAM SDTR2 Options
+ */
+#define SDRAM_SDTR2_RCD_MASK 0xF0000000
+#define SDRAM_SDTR2_RCD_1_CLK 0x10000000
+#define SDRAM_SDTR2_RCD_2_CLK 0x20000000
+#define SDRAM_SDTR2_RCD_3_CLK 0x30000000
+#define SDRAM_SDTR2_RCD_4_CLK 0x40000000
+#define SDRAM_SDTR2_RCD_5_CLK 0x50000000
+#define SDRAM_SDTR2_WTR_MASK 0x0F000000
+#define SDRAM_SDTR2_WTR_1_CLK 0x01000000
+#define SDRAM_SDTR2_WTR_2_CLK 0x02000000
+#define SDRAM_SDTR2_WTR_3_CLK 0x03000000
+#define SDRAM_SDTR2_WTR_4_CLK 0x04000000
+#define SDRAM_SDTR3_WTR_ENCODE(n) ((((u32)(n))&0xF)<<24)
+#define SDRAM_SDTR2_XSNR_MASK 0x00FF0000
+#define SDRAM_SDTR2_XSNR_8_CLK 0x00080000
+#define SDRAM_SDTR2_XSNR_16_CLK 0x00100000
+#define SDRAM_SDTR2_XSNR_32_CLK 0x00200000
+#define SDRAM_SDTR2_XSNR_64_CLK 0x00400000
+#define SDRAM_SDTR2_WPC_MASK 0x0000F000
+#define SDRAM_SDTR2_WPC_2_CLK 0x00002000
+#define SDRAM_SDTR2_WPC_3_CLK 0x00003000
+#define SDRAM_SDTR2_WPC_4_CLK 0x00004000
+#define SDRAM_SDTR2_WPC_5_CLK 0x00005000
+#define SDRAM_SDTR2_WPC_6_CLK 0x00006000
+#define SDRAM_SDTR3_WPC_ENCODE(n) ((((u32)(n))&0xF)<<12)
+#define SDRAM_SDTR2_RPC_MASK 0x00000F00
+#define SDRAM_SDTR2_RPC_2_CLK 0x00000200
+#define SDRAM_SDTR2_RPC_3_CLK 0x00000300
+#define SDRAM_SDTR2_RPC_4_CLK 0x00000400
+#define SDRAM_SDTR2_RP_MASK 0x000000F0
+#define SDRAM_SDTR2_RP_3_CLK 0x00000030
+#define SDRAM_SDTR2_RP_4_CLK 0x00000040
+#define SDRAM_SDTR2_RP_5_CLK 0x00000050
+#define SDRAM_SDTR2_RP_6_CLK 0x00000060
+#define SDRAM_SDTR2_RP_7_CLK 0x00000070
+#define SDRAM_SDTR2_RRD_MASK 0x0000000F
+#define SDRAM_SDTR2_RRD_2_CLK 0x00000002
+#define SDRAM_SDTR2_RRD_3_CLK 0x00000003
+
+/*
+ * SDRAM SDTR3 Options
+ */
+#define SDRAM_SDTR3_RAS_MASK 0x1F000000
+#define SDRAM_SDTR3_RAS_ENCODE(n) ((((u32)(n))&0x1F)<<24)
+#define SDRAM_SDTR3_RC_MASK 0x001F0000
+#define SDRAM_SDTR3_RC_ENCODE(n) ((((u32)(n))&0x1F)<<16)
+#define SDRAM_SDTR3_XCS_MASK 0x00001F00
+#define SDRAM_SDTR3_XCS 0x00000D00
+#define SDRAM_SDTR3_RFC_MASK 0x0000003F
+#define SDRAM_SDTR3_RFC_ENCODE(n) ((((u32)(n))&0x3F)<<0)
+
+/*
+ * Memory Bank 0-1 configuration
+ */
+#define SDRAM_BXCF_M_AM_MASK 0x00000F00 /* Addressing mode */
+#define SDRAM_BXCF_M_AM_0 0x00000000 /* Mode 0 */
+#define SDRAM_BXCF_M_AM_1 0x00000100 /* Mode 1 */
+#define SDRAM_BXCF_M_AM_2 0x00000200 /* Mode 2 */
+#define SDRAM_BXCF_M_AM_3 0x00000300 /* Mode 3 */
+#define SDRAM_BXCF_M_AM_4 0x00000400 /* Mode 4 */
+#define SDRAM_BXCF_M_AM_5 0x00000500 /* Mode 5 */
+#define SDRAM_BXCF_M_AM_6 0x00000600 /* Mode 6 */
+#define SDRAM_BXCF_M_AM_7 0x00000700 /* Mode 7 */
+#define SDRAM_BXCF_M_AM_8 0x00000800 /* Mode 8 */
+#define SDRAM_BXCF_M_AM_9 0x00000900 /* Mode 9 */
+#define SDRAM_BXCF_M_BE_MASK 0x00000001 /* Memory Bank Enable */
+#define SDRAM_BXCF_M_BE_DISABLE 0x00000000 /* Memory Bank Enable */
+#define SDRAM_BXCF_M_BE_ENABLE 0x00000001 /* Memory Bank Enable */
+
+#define SDRAM_RTSR_TRK1SM_MASK 0xC0000000 /* Tracking State Mach 1*/
+#define SDRAM_RTSR_TRK1SM_ATBASE 0x00000000 /* atbase state */
+#define SDRAM_RTSR_TRK1SM_MISSED 0x40000000 /* missed state */
+#define SDRAM_RTSR_TRK1SM_ATPLS1 0x80000000 /* atpls1 state */
+#define SDRAM_RTSR_TRK1SM_RESET 0xC0000000 /* reset state */
+
+#define SDR0_MFR_FIXD 0x10000000 /* Workaround for PCI/DMA */
+
+#endif /* CONFIG_SDRAM_PPC4xx_IBM_DDR2 */
+
+#if defined(CONFIG_SDRAM_PPC4xx_DENALI_DDR2)
+/*
+ * SDRAM Controller
+ */
+#define DDR0_00 0x00
+#define DDR0_00_INT_ACK_MASK 0x7F000000 /* Write only */
+#define DDR0_00_INT_ACK_ALL 0x7F000000
+#define DDR0_00_INT_ACK_ENCODE(n) ((((u32)(n))&0x7F)<<24)
+#define DDR0_00_INT_ACK_DECODE(n) ((((u32)(n))>>24)&0x7F)
+/* Status */
+#define DDR0_00_INT_STATUS_MASK 0x00FF0000 /* Read only */
+/* Bit0. A single access outside the defined PHYSICAL memory space detected. */
+#define DDR0_00_INT_STATUS_BIT0 0x00010000
+/* Bit1. Multiple accesses outside the defined PHYSICAL memory space detected. */
+#define DDR0_00_INT_STATUS_BIT1 0x00020000
+/* Bit2. Single correctable ECC event detected */
+#define DDR0_00_INT_STATUS_BIT2 0x00040000
+/* Bit3. Multiple correctable ECC events detected. */
+#define DDR0_00_INT_STATUS_BIT3 0x00080000
+/* Bit4. Single uncorrectable ECC event detected. */
+#define DDR0_00_INT_STATUS_BIT4 0x00100000
+/* Bit5. Multiple uncorrectable ECC events detected. */
+#define DDR0_00_INT_STATUS_BIT5 0x00200000
+/* Bit6. DRAM initialization complete. */
+#define DDR0_00_INT_STATUS_BIT6 0x00400000
+/* Bit7. Logical OR of all lower bits. */
+#define DDR0_00_INT_STATUS_BIT7 0x00800000
+
+#define DDR0_00_INT_STATUS_ENCODE(n) ((((u32)(n))&0xFF)<<16)
+#define DDR0_00_INT_STATUS_DECODE(n) ((((u32)(n))>>16)&0xFF)
+#define DDR0_00_DLL_INCREMENT_MASK 0x00007F00
+#define DDR0_00_DLL_INCREMENT_ENCODE(n) ((((u32)(n))&0x7F)<<8)
+#define DDR0_00_DLL_INCREMENT_DECODE(n) ((((u32)(n))>>8)&0x7F)
+#define DDR0_00_DLL_START_POINT_MASK 0x0000007F
+#define DDR0_00_DLL_START_POINT_ENCODE(n) ((((u32)(n))&0x7F)<<0)
+#define DDR0_00_DLL_START_POINT_DECODE(n) ((((u32)(n))>>0)&0x7F)
+
+#define DDR0_01 0x01
+#define DDR0_01_PLB0_DB_CS_LOWER_MASK 0x1F000000
+#define DDR0_01_PLB0_DB_CS_LOWER_ENCODE(n) ((((u32)(n))&0x1F)<<24)
+#define DDR0_01_PLB0_DB_CS_LOWER_DECODE(n) ((((u32)(n))>>24)&0x1F)
+#define DDR0_01_PLB0_DB_CS_UPPER_MASK 0x001F0000
+#define DDR0_01_PLB0_DB_CS_UPPER_ENCODE(n) ((((u32)(n))&0x1F)<<16)
+#define DDR0_01_PLB0_DB_CS_UPPER_DECODE(n) ((((u32)(n))>>16)&0x1F)
+#define DDR0_01_OUT_OF_RANGE_TYPE_MASK 0x00000700 /* Read only */
+#define DDR0_01_OUT_OF_RANGE_TYPE_ENCODE(n) ((((u32)(n))&0x7)<<8)
+#define DDR0_01_OUT_OF_RANGE_TYPE_DECODE(n) ((((u32)(n))>>8)&0x7)
+#define DDR0_01_INT_MASK_MASK 0x000000FF
+#define DDR0_01_INT_MASK_ENCODE(n) ((((u32)(n))&0xFF)<<0)
+#define DDR0_01_INT_MASK_DECODE(n) ((((u32)(n))>>0)&0xFF)
+#define DDR0_01_INT_MASK_ALL_ON 0x000000FF
+#define DDR0_01_INT_MASK_ALL_OFF 0x00000000
+
+#define DDR0_02 0x02
+#define DDR0_02_MAX_CS_REG_MASK 0x02000000 /* Read only */
+#define DDR0_02_MAX_CS_REG_ENCODE(n) ((((u32)(n))&0x2)<<24)
+#define DDR0_02_MAX_CS_REG_DECODE(n) ((((u32)(n))>>24)&0x2)
+#define DDR0_02_MAX_COL_REG_MASK 0x000F0000 /* Read only */
+#define DDR0_02_MAX_COL_REG_ENCODE(n) ((((u32)(n))&0xF)<<16)
+#define DDR0_02_MAX_COL_REG_DECODE(n) ((((u32)(n))>>16)&0xF)
+#define DDR0_02_MAX_ROW_REG_MASK 0x00000F00 /* Read only */
+#define DDR0_02_MAX_ROW_REG_ENCODE(n) ((((u32)(n))&0xF)<<8)
+#define DDR0_02_MAX_ROW_REG_DECODE(n) ((((u32)(n))>>8)&0xF)
+#define DDR0_02_START_MASK 0x00000001
+#define DDR0_02_START_ENCODE(n) ((((u32)(n))&0x1)<<0)
+#define DDR0_02_START_DECODE(n) ((((u32)(n))>>0)&0x1)
+#define DDR0_02_START_OFF 0x00000000
+#define DDR0_02_START_ON 0x00000001
+
+#define DDR0_03 0x03
+#define DDR0_03_BSTLEN_MASK 0x07000000
+#define DDR0_03_BSTLEN_ENCODE(n) ((((u32)(n))&0x7)<<24)
+#define DDR0_03_BSTLEN_DECODE(n) ((((u32)(n))>>24)&0x7)
+#define DDR0_03_CASLAT_MASK 0x00070000
+#define DDR0_03_CASLAT_ENCODE(n) ((((u32)(n))&0x7)<<16)
+#define DDR0_03_CASLAT_DECODE(n) ((((u32)(n))>>16)&0x7)
+#define DDR0_03_CASLAT_LIN_MASK 0x00000F00
+#define DDR0_03_CASLAT_LIN_ENCODE(n) ((((u32)(n))&0xF)<<8)
+#define DDR0_03_CASLAT_LIN_DECODE(n) ((((u32)(n))>>8)&0xF)
+#define DDR0_03_INITAREF_MASK 0x0000000F
+#define DDR0_03_INITAREF_ENCODE(n) ((((u32)(n))&0xF)<<0)
+#define DDR0_03_INITAREF_DECODE(n) ((((u32)(n))>>0)&0xF)
+
+#define DDR0_04 0x04
+#define DDR0_04_TRC_MASK 0x1F000000
+#define DDR0_04_TRC_ENCODE(n) ((((u32)(n))&0x1F)<<24)
+#define DDR0_04_TRC_DECODE(n) ((((u32)(n))>>24)&0x1F)
+#define DDR0_04_TRRD_MASK 0x00070000
+#define DDR0_04_TRRD_ENCODE(n) ((((u32)(n))&0x7)<<16)
+#define DDR0_04_TRRD_DECODE(n) ((((u32)(n))>>16)&0x7)
+#define DDR0_04_TRTP_MASK 0x00000700
+#define DDR0_04_TRTP_ENCODE(n) ((((u32)(n))&0x7)<<8)
+#define DDR0_04_TRTP_DECODE(n) ((((u32)(n))>>8)&0x7)
+
+#define DDR0_05 0x05
+#define DDR0_05_TMRD_MASK 0x1F000000
+#define DDR0_05_TMRD_ENCODE(n) ((((u32)(n))&0x1F)<<24)
+#define DDR0_05_TMRD_DECODE(n) ((((u32)(n))>>24)&0x1F)
+#define DDR0_05_TEMRS_MASK 0x00070000
+#define DDR0_05_TEMRS_ENCODE(n) ((((u32)(n))&0x7)<<16)
+#define DDR0_05_TEMRS_DECODE(n) ((((u32)(n))>>16)&0x7)
+#define DDR0_05_TRP_MASK 0x00000F00
+#define DDR0_05_TRP_ENCODE(n) ((((u32)(n))&0xF)<<8)
+#define DDR0_05_TRP_DECODE(n) ((((u32)(n))>>8)&0xF)
+#define DDR0_05_TRAS_MIN_MASK 0x000000FF
+#define DDR0_05_TRAS_MIN_ENCODE(n) ((((u32)(n))&0xFF)<<0)
+#define DDR0_05_TRAS_MIN_DECODE(n) ((((u32)(n))>>0)&0xFF)
+
+#define DDR0_06 0x06
+#define DDR0_06_WRITEINTERP_MASK 0x01000000
+#define DDR0_06_WRITEINTERP_ENCODE(n) ((((u32)(n))&0x1)<<24)
+#define DDR0_06_WRITEINTERP_DECODE(n) ((((u32)(n))>>24)&0x1)
+#define DDR0_06_TWTR_MASK 0x00070000
+#define DDR0_06_TWTR_ENCODE(n) ((((u32)(n))&0x7)<<16)
+#define DDR0_06_TWTR_DECODE(n) ((((u32)(n))>>16)&0x7)
+#define DDR0_06_TDLL_MASK 0x0000FF00
+#define DDR0_06_TDLL_ENCODE(n) ((((u32)(n))&0xFF)<<8)
+#define DDR0_06_TDLL_DECODE(n) ((((u32)(n))>>8)&0xFF)
+#define DDR0_06_TRFC_MASK 0x0000007F
+#define DDR0_06_TRFC_ENCODE(n) ((((u32)(n))&0x7F)<<0)
+#define DDR0_06_TRFC_DECODE(n) ((((u32)(n))>>0)&0x7F)
+
+#define DDR0_07 0x07
+#define DDR0_07_NO_CMD_INIT_MASK 0x01000000
+#define DDR0_07_NO_CMD_INIT_ENCODE(n) ((((u32)(n))&0x1)<<24)
+#define DDR0_07_NO_CMD_INIT_DECODE(n) ((((u32)(n))>>24)&0x1)
+#define DDR0_07_TFAW_MASK 0x001F0000
+#define DDR0_07_TFAW_ENCODE(n) ((((u32)(n))&0x1F)<<16)
+#define DDR0_07_TFAW_DECODE(n) ((((u32)(n))>>16)&0x1F)
+#define DDR0_07_AUTO_REFRESH_MODE_MASK 0x00000100
+#define DDR0_07_AUTO_REFRESH_MODE_ENCODE(n) ((((u32)(n))&0x1)<<8)
+#define DDR0_07_AUTO_REFRESH_MODE_DECODE(n) ((((u32)(n))>>8)&0x1)
+#define DDR0_07_AREFRESH_MASK 0x00000001
+#define DDR0_07_AREFRESH_ENCODE(n) ((((u32)(n))&0x1)<<0)
+#define DDR0_07_AREFRESH_DECODE(n) ((((u32)(n))>>0)&0x1)
+
+#define DDR0_08 0x08
+#define DDR0_08_WRLAT_MASK 0x07000000
+#define DDR0_08_WRLAT_ENCODE(n) ((((u32)(n))&0x7)<<24)
+#define DDR0_08_WRLAT_DECODE(n) ((((u32)(n))>>24)&0x7)
+#define DDR0_08_TCPD_MASK 0x00FF0000
+#define DDR0_08_TCPD_ENCODE(n) ((((u32)(n))&0xFF)<<16)
+#define DDR0_08_TCPD_DECODE(n) ((((u32)(n))>>16)&0xFF)
+#define DDR0_08_DQS_N_EN_MASK 0x00000100
+#define DDR0_08_DQS_N_EN_ENCODE(n) ((((u32)(n))&0x1)<<8)
+#define DDR0_08_DQS_N_EN_DECODE(n) ((((u32)(n))>>8)&0x1)
+#define DDR0_08_DDRII_SDRAM_MODE_MASK 0x00000001
+#define DDR0_08_DDRII_ENCODE(n) ((((u32)(n))&0x1)<<0)
+#define DDR0_08_DDRII_DECODE(n) ((((u32)(n))>>0)&0x1)
+
+#define DDR0_09 0x09
+#define DDR0_09_OCD_ADJUST_PDN_CS_0_MASK 0x1F000000
+#define DDR0_09_OCD_ADJUST_PDN_CS_0_ENCODE(n) ((((u32)(n))&0x1F)<<24)
+#define DDR0_09_OCD_ADJUST_PDN_CS_0_DECODE(n) ((((u32)(n))>>24)&0x1F)
+#define DDR0_09_RTT_0_MASK 0x00030000
+#define DDR0_09_RTT_0_ENCODE(n) ((((u32)(n))&0x3)<<16)
+#define DDR0_09_RTT_0_DECODE(n) ((((u32)(n))>>16)&0x3)
+#define DDR0_09_WR_DQS_SHIFT_BYPASS_MASK 0x00007F00
+#define DDR0_09_WR_DQS_SHIFT_BYPASS_ENCODE(n) ((((u32)(n))&0x7F)<<8)
+#define DDR0_09_WR_DQS_SHIFT_BYPASS_DECODE(n) ((((u32)(n))>>8)&0x7F)
+#define DDR0_09_WR_DQS_SHIFT_MASK 0x0000007F
+#define DDR0_09_WR_DQS_SHIFT_ENCODE(n) ((((u32)(n))&0x7F)<<0)
+#define DDR0_09_WR_DQS_SHIFT_DECODE(n) ((((u32)(n))>>0)&0x7F)
+
+#define DDR0_10 0x0A
+#define DDR0_10_WRITE_MODEREG_MASK 0x00010000 /* Write only */
+#define DDR0_10_WRITE_MODEREG_ENCODE(n) ((((u32)(n))&0x1)<<16)
+#define DDR0_10_WRITE_MODEREG_DECODE(n) ((((u32)(n))>>16)&0x1)
+#define DDR0_10_CS_MAP_MASK 0x00000300
+#define DDR0_10_CS_MAP_NO_MEM 0x00000000
+#define DDR0_10_CS_MAP_RANK0_INSTALLED 0x00000100
+#define DDR0_10_CS_MAP_RANK1_INSTALLED 0x00000200
+#define DDR0_10_CS_MAP_ENCODE(n) ((((u32)(n))&0x3)<<8)
+#define DDR0_10_CS_MAP_DECODE(n) ((((u32)(n))>>8)&0x3)
+#define DDR0_10_OCD_ADJUST_PUP_CS_0_MASK 0x0000001F
+#define DDR0_10_OCD_ADJUST_PUP_CS_0_ENCODE(n) ((((u32)(n))&0x1F)<<0)
+#define DDR0_10_OCD_ADJUST_PUP_CS_0_DECODE(n) ((((u32)(n))>>0)&0x1F)
+
+#define DDR0_11 0x0B
+#define DDR0_11_SREFRESH_MASK 0x01000000
+#define DDR0_11_SREFRESH_ENCODE(n) ((((u32)(n))&0x1)<<24)
+#define DDR0_11_SREFRESH_DECODE(n) ((((u32)(n))>>24)&0x1F)
+#define DDR0_11_TXSNR_MASK 0x00FF0000
+#define DDR0_11_TXSNR_ENCODE(n) ((((u32)(n))&0xFF)<<16)
+#define DDR0_11_TXSNR_DECODE(n) ((((u32)(n))>>16)&0xFF)
+#define DDR0_11_TXSR_MASK 0x0000FF00
+#define DDR0_11_TXSR_ENCODE(n) ((((u32)(n))&0xFF)<<8)
+#define DDR0_11_TXSR_DECODE(n) ((((u32)(n))>>8)&0xFF)
+
+#define DDR0_12 0x0C
+#define DDR0_12_TCKE_MASK 0x0000007
+#define DDR0_12_TCKE_ENCODE(n) ((((u32)(n))&0x7)<<0)
+#define DDR0_12_TCKE_DECODE(n) ((((u32)(n))>>0)&0x7)
+
+#define DDR0_14 0x0E
+#define DDR0_14_DLL_BYPASS_MODE_MASK 0x01000000
+#define DDR0_14_DLL_BYPASS_MODE_ENCODE(n) ((((u32)(n))&0x1)<<24)
+#define DDR0_14_DLL_BYPASS_MODE_DECODE(n) ((((u32)(n))>>24)&0x1)
+#define DDR0_14_REDUC_MASK 0x00010000
+#define DDR0_14_REDUC_64BITS 0x00000000
+#define DDR0_14_REDUC_32BITS 0x00010000
+#define DDR0_14_REDUC_ENCODE(n) ((((u32)(n))&0x1)<<16)
+#define DDR0_14_REDUC_DECODE(n) ((((u32)(n))>>16)&0x1)
+#define DDR0_14_REG_DIMM_ENABLE_MASK 0x00000100
+#define DDR0_14_REG_DIMM_ENABLE_ENCODE(n) ((((u32)(n))&0x1)<<8)
+#define DDR0_14_REG_DIMM_ENABLE_DECODE(n) ((((u32)(n))>>8)&0x1)
+
+#define DDR0_17 0x11
+#define DDR0_17_DLL_DQS_DELAY_0_MASK 0x7F000000
+#define DDR0_17_DLL_DQS_DELAY_0_ENCODE(n) ((((u32)(n))&0x7F)<<24)
+#define DDR0_17_DLL_DQS_DELAY_0_DECODE(n) ((((u32)(n))>>24)&0x7F)
+#define DDR0_17_DLLLOCKREG_MASK 0x00010000 /* Read only */
+#define DDR0_17_DLLLOCKREG_LOCKED 0x00010000
+#define DDR0_17_DLLLOCKREG_UNLOCKED 0x00000000
+#define DDR0_17_DLLLOCKREG_ENCODE(n) ((((u32)(n))&0x1)<<16)
+#define DDR0_17_DLLLOCKREG_DECODE(n) ((((u32)(n))>>16)&0x1)
+#define DDR0_17_DLL_LOCK_MASK 0x00007F00 /* Read only */
+#define DDR0_17_DLL_LOCK_ENCODE(n) ((((u32)(n))&0x7F)<<8)
+#define DDR0_17_DLL_LOCK_DECODE(n) ((((u32)(n))>>8)&0x7F)
+
+#define DDR0_18 0x12
+#define DDR0_18_DLL_DQS_DELAY_X_MASK 0x7F7F7F7F
+#define DDR0_18_DLL_DQS_DELAY_4_MASK 0x7F000000
+#define DDR0_18_DLL_DQS_DELAY_4_ENCODE(n) ((((u32)(n))&0x7F)<<24)
+#define DDR0_18_DLL_DQS_DELAY_4_DECODE(n) ((((u32)(n))>>24)&0x7F)
+#define DDR0_18_DLL_DQS_DELAY_3_MASK 0x007F0000
+#define DDR0_18_DLL_DQS_DELAY_3_ENCODE(n) ((((u32)(n))&0x7F)<<16)
+#define DDR0_18_DLL_DQS_DELAY_3_DECODE(n) ((((u32)(n))>>16)&0x7F)
+#define DDR0_18_DLL_DQS_DELAY_2_MASK 0x00007F00
+#define DDR0_18_DLL_DQS_DELAY_2_ENCODE(n) ((((u32)(n))&0x7F)<<8)
+#define DDR0_18_DLL_DQS_DELAY_2_DECODE(n) ((((u32)(n))>>8)&0x7F)
+#define DDR0_18_DLL_DQS_DELAY_1_MASK 0x0000007F
+#define DDR0_18_DLL_DQS_DELAY_1_ENCODE(n) ((((u32)(n))&0x7F)<<0)
+#define DDR0_18_DLL_DQS_DELAY_1_DECODE(n) ((((u32)(n))>>0)&0x7F)
+
+#define DDR0_19 0x13
+#define DDR0_19_DLL_DQS_DELAY_X_MASK 0x7F7F7F7F
+#define DDR0_19_DLL_DQS_DELAY_8_MASK 0x7F000000
+#define DDR0_19_DLL_DQS_DELAY_8_ENCODE(n) ((((u32)(n))&0x7F)<<24)
+#define DDR0_19_DLL_DQS_DELAY_8_DECODE(n) ((((u32)(n))>>24)&0x7F)
+#define DDR0_19_DLL_DQS_DELAY_7_MASK 0x007F0000
+#define DDR0_19_DLL_DQS_DELAY_7_ENCODE(n) ((((u32)(n))&0x7F)<<16)
+#define DDR0_19_DLL_DQS_DELAY_7_DECODE(n) ((((u32)(n))>>16)&0x7F)
+#define DDR0_19_DLL_DQS_DELAY_6_MASK 0x00007F00
+#define DDR0_19_DLL_DQS_DELAY_6_ENCODE(n) ((((u32)(n))&0x7F)<<8)
+#define DDR0_19_DLL_DQS_DELAY_6_DECODE(n) ((((u32)(n))>>8)&0x7F)
+#define DDR0_19_DLL_DQS_DELAY_5_MASK 0x0000007F
+#define DDR0_19_DLL_DQS_DELAY_5_ENCODE(n) ((((u32)(n))&0x7F)<<0)
+#define DDR0_19_DLL_DQS_DELAY_5_DECODE(n) ((((u32)(n))>>0)&0x7F)
+
+#define DDR0_20 0x14
+#define DDR0_20_DLL_DQS_BYPASS_3_MASK 0x7F000000
+#define DDR0_20_DLL_DQS_BYPASS_3_ENCODE(n) ((((u32)(n))&0x7F)<<24)
+#define DDR0_20_DLL_DQS_BYPASS_3_DECODE(n) ((((u32)(n))>>24)&0x7F)
+#define DDR0_20_DLL_DQS_BYPASS_2_MASK 0x007F0000
+#define DDR0_20_DLL_DQS_BYPASS_2_ENCODE(n) ((((u32)(n))&0x7F)<<16)
+#define DDR0_20_DLL_DQS_BYPASS_2_DECODE(n) ((((u32)(n))>>16)&0x7F)
+#define DDR0_20_DLL_DQS_BYPASS_1_MASK 0x00007F00
+#define DDR0_20_DLL_DQS_BYPASS_1_ENCODE(n) ((((u32)(n))&0x7F)<<8)
+#define DDR0_20_DLL_DQS_BYPASS_1_DECODE(n) ((((u32)(n))>>8)&0x7F)
+#define DDR0_20_DLL_DQS_BYPASS_0_MASK 0x0000007F
+#define DDR0_20_DLL_DQS_BYPASS_0_ENCODE(n) ((((u32)(n))&0x7F)<<0)
+#define DDR0_20_DLL_DQS_BYPASS_0_DECODE(n) ((((u32)(n))>>0)&0x7F)
+
+#define DDR0_21 0x15
+#define DDR0_21_DLL_DQS_BYPASS_7_MASK 0x7F000000
+#define DDR0_21_DLL_DQS_BYPASS_7_ENCODE(n) ((((u32)(n))&0x7F)<<24)
+#define DDR0_21_DLL_DQS_BYPASS_7_DECODE(n) ((((u32)(n))>>24)&0x7F)
+#define DDR0_21_DLL_DQS_BYPASS_6_MASK 0x007F0000
+#define DDR0_21_DLL_DQS_BYPASS_6_ENCODE(n) ((((u32)(n))&0x7F)<<16)
+#define DDR0_21_DLL_DQS_BYPASS_6_DECODE(n) ((((u32)(n))>>16)&0x7F)
+#define DDR0_21_DLL_DQS_BYPASS_5_MASK 0x00007F00
+#define DDR0_21_DLL_DQS_BYPASS_5_ENCODE(n) ((((u32)(n))&0x7F)<<8)
+#define DDR0_21_DLL_DQS_BYPASS_5_DECODE(n) ((((u32)(n))>>8)&0x7F)
+#define DDR0_21_DLL_DQS_BYPASS_4_MASK 0x0000007F
+#define DDR0_21_DLL_DQS_BYPASS_4_ENCODE(n) ((((u32)(n))&0x7F)<<0)
+#define DDR0_21_DLL_DQS_BYPASS_4_DECODE(n) ((((u32)(n))>>0)&0x7F)
+
+#define DDR0_22 0x16
+#define DDR0_22_CTRL_RAW_MASK 0x03000000
+#define DDR0_22_CTRL_RAW_ECC_DISABLE 0x00000000
+#define DDR0_22_CTRL_RAW_ECC_CHECK_ONLY 0x01000000
+#define DDR0_22_CTRL_RAW_NO_ECC_RAM 0x02000000
+#define DDR0_22_CTRL_RAW_ECC_ENABLE 0x03000000
+#define DDR0_22_CTRL_RAW_ENCODE(n) ((((u32)(n))&0x3)<<24)
+#define DDR0_22_CTRL_RAW_DECODE(n) ((((u32)(n))>>24)&0x3)
+#define DDR0_22_DQS_OUT_SHIFT_BYPASS_MASK 0x007F0000
+#define DDR0_22_DQS_OUT_SHIFT_BYPASS_ENCODE(n) ((((u32)(n))&0x7F)<<16)
+#define DDR0_22_DQS_OUT_SHIFT_BYPASS_DECODE(n) ((((u32)(n))>>16)&0x7F)
+#define DDR0_22_DQS_OUT_SHIFT_MASK 0x00007F00
+#define DDR0_22_DQS_OUT_SHIFT_ENCODE(n) ((((u32)(n))&0x7F)<<8)
+#define DDR0_22_DQS_OUT_SHIFT_DECODE(n) ((((u32)(n))>>8)&0x7F)
+#define DDR0_22_DLL_DQS_BYPASS_8_MASK 0x0000007F
+#define DDR0_22_DLL_DQS_BYPASS_8_ENCODE(n) ((((u32)(n))&0x7F)<<0)
+#define DDR0_22_DLL_DQS_BYPASS_8_DECODE(n) ((((u32)(n))>>0)&0x7F)
+
+#define DDR0_23 0x17
+#define DDR0_23_ODT_RD_MAP_CS0_MASK 0x03000000
+#define DDR0_23_ODT_RD_MAP_CS0_ENCODE(n) ((((u32)(n))&0x3)<<24)
+#define DDR0_23_ODT_RD_MAP_CS0_DECODE(n) ((((u32)(n))>>24)&0x3)
+#define DDR0_23_ECC_C_SYND_MASK 0x00FF0000 /* Read only */
+#define DDR0_23_ECC_C_SYND_ENCODE(n) ((((u32)(n))&0xFF)<<16)
+#define DDR0_23_ECC_C_SYND_DECODE(n) ((((u32)(n))>>16)&0xFF)
+#define DDR0_23_ECC_U_SYND_MASK 0x0000FF00 /* Read only */
+#define DDR0_23_ECC_U_SYND_ENCODE(n) ((((u32)(n))&0xFF)<<8)
+#define DDR0_23_ECC_U_SYND_DECODE(n) ((((u32)(n))>>8)&0xFF)
+#define DDR0_23_FWC_MASK 0x00000001 /* Write only */
+#define DDR0_23_FWC_ENCODE(n) ((((u32)(n))&0x1)<<0)
+#define DDR0_23_FWC_DECODE(n) ((((u32)(n))>>0)&0x1)
+
+#define DDR0_24 0x18
+#define DDR0_24_RTT_PAD_TERMINATION_MASK 0x03000000
+#define DDR0_24_RTT_PAD_TERMINATION_ENCODE(n) ((((u32)(n))&0x3)<<24)
+#define DDR0_24_RTT_PAD_TERMINATION_DECODE(n) ((((u32)(n))>>24)&0x3)
+#define DDR0_24_ODT_WR_MAP_CS1_MASK 0x00030000
+#define DDR0_24_ODT_WR_MAP_CS1_ENCODE(n) ((((u32)(n))&0x3)<<16)
+#define DDR0_24_ODT_WR_MAP_CS1_DECODE(n) ((((u32)(n))>>16)&0x3)
+#define DDR0_24_ODT_RD_MAP_CS1_MASK 0x00000300
+#define DDR0_24_ODT_RD_MAP_CS1_ENCODE(n) ((((u32)(n))&0x3)<<8)
+#define DDR0_24_ODT_RD_MAP_CS1_DECODE(n) ((((u32)(n))>>8)&0x3)
+#define DDR0_24_ODT_WR_MAP_CS0_MASK 0x00000003
+#define DDR0_24_ODT_WR_MAP_CS0_ENCODE(n) ((((u32)(n))&0x3)<<0)
+#define DDR0_24_ODT_WR_MAP_CS0_DECODE(n) ((((u32)(n))>>0)&0x3)
+
+#define DDR0_25 0x19
+#define DDR0_25_VERSION_MASK 0xFFFF0000 /* Read only */
+#define DDR0_25_VERSION_ENCODE(n) ((((u32)(n))&0xFFFF)<<16)
+#define DDR0_25_VERSION_DECODE(n) ((((u32)(n))>>16)&0xFFFF)
+#define DDR0_25_OUT_OF_RANGE_LENGTH_MASK 0x000003FF /* Read only */
+#define DDR0_25_OUT_OF_RANGE_LENGTH_ENCODE(n) ((((u32)(n))&0x3FF)<<0)
+#define DDR0_25_OUT_OF_RANGE_LENGTH_DECODE(n) ((((u32)(n))>>0)&0x3FF)
+
+#define DDR0_26 0x1A
+#define DDR0_26_TRAS_MAX_MASK 0xFFFF0000
+#define DDR0_26_TRAS_MAX_ENCODE(n) ((((u32)(n))&0xFFFF)<<16)
+#define DDR0_26_TRAS_MAX_DECODE(n) ((((u32)(n))>>16)&0xFFFF)
+#define DDR0_26_TREF_MASK 0x00003FFF
+#define DDR0_26_TREF_ENCODE(n) ((((u32)(n))&0x3FFF)<<0)
+#define DDR0_26_TREF_DECODE(n) ((((u32)(n))>>0)&0x3FFF)
+
+#define DDR0_27 0x1B
+#define DDR0_27_EMRS_DATA_MASK 0x3FFF0000
+#define DDR0_27_EMRS_DATA_ENCODE(n) ((((u32)(n))&0x3FFF)<<16)
+#define DDR0_27_EMRS_DATA_DECODE(n) ((((u32)(n))>>16)&0x3FFF)
+#define DDR0_27_TINIT_MASK 0x0000FFFF
+#define DDR0_27_TINIT_ENCODE(n) ((((u32)(n))&0xFFFF)<<0)
+#define DDR0_27_TINIT_DECODE(n) ((((u32)(n))>>0)&0xFFFF)
+
+#define DDR0_28 0x1C
+#define DDR0_28_EMRS3_DATA_MASK 0x3FFF0000
+#define DDR0_28_EMRS3_DATA_ENCODE(n) ((((u32)(n))&0x3FFF)<<16)
+#define DDR0_28_EMRS3_DATA_DECODE(n) ((((u32)(n))>>16)&0x3FFF)
+#define DDR0_28_EMRS2_DATA_MASK 0x00003FFF
+#define DDR0_28_EMRS2_DATA_ENCODE(n) ((((u32)(n))&0x3FFF)<<0)
+#define DDR0_28_EMRS2_DATA_DECODE(n) ((((u32)(n))>>0)&0x3FFF)
+
+#define DDR0_31 0x1F
+#define DDR0_31_XOR_CHECK_BITS_MASK 0x0000FFFF
+#define DDR0_31_XOR_CHECK_BITS_ENCODE(n) ((((u32)(n))&0xFFFF)<<0)
+#define DDR0_31_XOR_CHECK_BITS_DECODE(n) ((((u32)(n))>>0)&0xFFFF)
+
+#define DDR0_32 0x20
+#define DDR0_32_OUT_OF_RANGE_ADDR_MASK 0xFFFFFFFF /* Read only */
+#define DDR0_32_OUT_OF_RANGE_ADDR_ENCODE(n) ((((u32)(n))&0xFFFFFFFF)<<0)
+#define DDR0_32_OUT_OF_RANGE_ADDR_DECODE(n) ((((u32)(n))>>0)&0xFFFFFFFF)
+
+#define DDR0_33 0x21
+#define DDR0_33_OUT_OF_RANGE_ADDR_MASK 0x00000001 /* Read only */
+#define DDR0_33_OUT_OF_RANGE_ADDR_ENCODE(n) ((((u32)(n))&0x1)<<0)
+#define DDR0_33_OUT_OF_RANGE_ADDR_DECODE(n) ((((u32)(n))>>0)&0x1)
+
+#define DDR0_34 0x22
+#define DDR0_34_ECC_U_ADDR_MASK 0xFFFFFFFF /* Read only */
+#define DDR0_34_ECC_U_ADDR_ENCODE(n) ((((u32)(n))&0xFFFFFFFF)<<0)
+#define DDR0_34_ECC_U_ADDR_DECODE(n) ((((u32)(n))>>0)&0xFFFFFFFF)
+
+#define DDR0_35 0x23
+#define DDR0_35_ECC_U_ADDR_MASK 0x00000001 /* Read only */
+#define DDR0_35_ECC_U_ADDR_ENCODE(n) ((((u32)(n))&0x1)<<0)
+#define DDR0_35_ECC_U_ADDR_DECODE(n) ((((u32)(n))>>0)&0x1)
+
+#define DDR0_36 0x24
+#define DDR0_36_ECC_U_DATA_MASK 0xFFFFFFFF /* Read only */
+#define DDR0_36_ECC_U_DATA_ENCODE(n) ((((u32)(n))&0xFFFFFFFF)<<0)
+#define DDR0_36_ECC_U_DATA_DECODE(n) ((((u32)(n))>>0)&0xFFFFFFFF)
+
+#define DDR0_37 0x25
+#define DDR0_37_ECC_U_DATA_MASK 0xFFFFFFFF /* Read only */
+#define DDR0_37_ECC_U_DATA_ENCODE(n) ((((u32)(n))&0xFFFFFFFF)<<0)
+#define DDR0_37_ECC_U_DATA_DECODE(n) ((((u32)(n))>>0)&0xFFFFFFFF)
+
+#define DDR0_38 0x26
+#define DDR0_38_ECC_C_ADDR_MASK 0xFFFFFFFF /* Read only */
+#define DDR0_38_ECC_C_ADDR_ENCODE(n) ((((u32)(n))&0xFFFFFFFF)<<0)
+#define DDR0_38_ECC_C_ADDR_DECODE(n) ((((u32)(n))>>0)&0xFFFFFFFF)
+
+#define DDR0_39 0x27
+#define DDR0_39_ECC_C_ADDR_MASK 0x00000001 /* Read only */
+#define DDR0_39_ECC_C_ADDR_ENCODE(n) ((((u32)(n))&0x1)<<0)
+#define DDR0_39_ECC_C_ADDR_DECODE(n) ((((u32)(n))>>0)&0x1)
+
+#define DDR0_40 0x28
+#define DDR0_40_ECC_C_DATA_MASK 0xFFFFFFFF /* Read only */
+#define DDR0_40_ECC_C_DATA_ENCODE(n) ((((u32)(n))&0xFFFFFFFF)<<0)
+#define DDR0_40_ECC_C_DATA_DECODE(n) ((((u32)(n))>>0)&0xFFFFFFFF)
+
+#define DDR0_41 0x29
+#define DDR0_41_ECC_C_DATA_MASK 0xFFFFFFFF /* Read only */
+#define DDR0_41_ECC_C_DATA_ENCODE(n) ((((u32)(n))&0xFFFFFFFF)<<0)
+#define DDR0_41_ECC_C_DATA_DECODE(n) ((((u32)(n))>>0)&0xFFFFFFFF)
+
+#define DDR0_42 0x2A
+#define DDR0_42_ADDR_PINS_MASK 0x07000000
+#define DDR0_42_ADDR_PINS_ENCODE(n) ((((u32)(n))&0x7)<<24)
+#define DDR0_42_ADDR_PINS_DECODE(n) ((((u32)(n))>>24)&0x7)
+#define DDR0_42_CASLAT_LIN_GATE_MASK 0x0000000F
+#define DDR0_42_CASLAT_LIN_GATE_ENCODE(n) ((((u32)(n))&0xF)<<0)
+#define DDR0_42_CASLAT_LIN_GATE_DECODE(n) ((((u32)(n))>>0)&0xF)
+
+#define DDR0_43 0x2B
+#define DDR0_43_TWR_MASK 0x07000000
+#define DDR0_43_TWR_ENCODE(n) ((((u32)(n))&0x7)<<24)
+#define DDR0_43_TWR_DECODE(n) ((((u32)(n))>>24)&0x7)
+#define DDR0_43_APREBIT_MASK 0x000F0000
+#define DDR0_43_APREBIT_ENCODE(n) ((((u32)(n))&0xF)<<16)
+#define DDR0_43_APREBIT_DECODE(n) ((((u32)(n))>>16)&0xF)
+#define DDR0_43_COLUMN_SIZE_MASK 0x00000700
+#define DDR0_43_COLUMN_SIZE_ENCODE(n) ((((u32)(n))&0x7)<<8)
+#define DDR0_43_COLUMN_SIZE_DECODE(n) ((((u32)(n))>>8)&0x7)
+#define DDR0_43_EIGHT_BANK_MODE_MASK 0x00000001
+#define DDR0_43_EIGHT_BANK_MODE_8_BANKS 0x00000001
+#define DDR0_43_EIGHT_BANK_MODE_4_BANKS 0x00000000
+#define DDR0_43_EIGHT_BANK_MODE_ENCODE(n) ((((u32)(n))&0x1)<<0)
+#define DDR0_43_EIGHT_BANK_MODE_DECODE(n) ((((u32)(n))>>0)&0x1)
+
+#define DDR0_44 0x2C
+#define DDR0_44_TRCD_MASK 0x000000FF
+#define DDR0_44_TRCD_ENCODE(n) ((((u32)(n))&0xFF)<<0)
+#define DDR0_44_TRCD_DECODE(n) ((((u32)(n))>>0)&0xFF)
+
+#endif /* CONFIG_SDRAM_PPC4xx_DENALI_DDR2 */
+
+#endif /* _PPC4xx_SDRAM_H_ */
#define SPRN_PID2 0x27a /* Process ID Register 2 */
#define SPRN_MCSR 0x23c /* Machine Check Syndrome register */
#define SPRN_MCAR 0x23d /* Machine Check Address register */
-#ifdef CONFIG_440
#define MCSR_MCS 0x80000000 /* Machine Check Summary */
#define MCSR_IB 0x40000000 /* Instruction PLB Error */
+#if defined(CONFIG_440)
#define MCSR_DRB 0x20000000 /* Data Read PLB Error */
#define MCSR_DWB 0x10000000 /* Data Write PLB Error */
+#else
+#define MCSR_DB 0x20000000 /* Data PLB Error */
+#endif /* defined(CONFIG_440) */
#define MCSR_TLBP 0x08000000 /* TLB Parity Error */
#define MCSR_ICP 0x04000000 /* I-Cache Parity Error */
#define MCSR_DCSP 0x02000000 /* D-Cache Search Parity Error */
#define MCSR_DCFP 0x01000000 /* D-Cache Flush Parity Error */
#define MCSR_IMPE 0x00800000 /* Imprecise Machine Check Exception */
-#endif
#define ESR_ST 0x00800000 /* Store Operation */
#if defined(CONFIG_MPC86xx)
#define CONFIG_CMD_FAT
#define CONFIG_CMD_ELF
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_BSP
#define CONFIG_CMD_EEPROM
-
-#if 0 /* test-only */
-#define CONFIG_NETCONSOLE
-#define CONFIG_NET_MULTI
-
-#ifdef CONFIG_NET_MULTI
-#define CONFIG_PHY1_ADDR 1 /* PHY address: for NetConsole */
-#endif
-#endif
-
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_SUPPORT_VFAT
-#if 0 /* test-only */
-#define CONFIG_AUTO_UPDATE 1 /* autoupdate via compactflash */
-#endif
-
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-
-/*
- * JFFS2 partitions
- */
-
-/* No command line, one static partition, use whole device */
-#undef CONFIG_JFFS2_CMDLINE
-#define CONFIG_JFFS2_DEV "nor0"
-#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET 0x00000000
-
-/* mtdparts command line support */
-
-/* Use first bank for JFFS2, second bank contains U-Boot.
- *
- * Note: fake mtd_id's used, no linux mtd map file.
- */
-/*
-#define CONFIG_JFFS2_CMDLINE
-#define MTDIDS_DEFAULT "nor0=cpci4052-0"
-#define MTDPARTS_DEFAULT "mtdparts=cpci4052-0:-(jffs2)"
-*/
-
#if 0 /* Use NVRAM for environment variables */
/*-----------------------------------------------------------------------
* NVRAM organization
#define CONFIG_CMD_FAT
#define CONFIG_CMD_ELF
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-/*
- * JFFS2 partitions
- */
-/* No command line, one static partition */
-#undef CONFIG_JFFS2_CMDLINE
-#define CONFIG_JFFS2_DEV "nor0"
-#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET 0x00000000
-
-/* mtdparts command line support */
-
-/* Use first bank for JFFS2, second bank contains U-Boot.
- *
- * Note: fake mtd_id's used, no linux mtd map file.
- */
-/*
-#define CONFIG_JFFS2_CMDLINE
-#define MTDIDS_DEFAULT "nor0=cpci405ab-0"
-#define MTDPARTS_DEFAULT "mtdparts=cpci405ab-0:-(jffs2)"
-*/
-
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC32) for environment
*/
#define CONFIG_CMD_FAT
#define CONFIG_CMD_ELF
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_BSP
#define CONFIG_CMD_EEPROM
-
-#if 0 /* test-only */
-#define CONFIG_NETCONSOLE
-#define CONFIG_NET_MULTI
-
-#ifdef CONFIG_NET_MULTI
-#define CONFIG_PHY1_ADDR 1 /* PHY address: for NetConsole */
-#endif
-#endif
-
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-/*
- * JFFS2 partitions
- */
-/* No command line, one static partition */
-#undef CONFIG_JFFS2_CMDLINE
-#define CONFIG_JFFS2_DEV "nor0"
-#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET 0x00000000
-
-/* mtdparts command line support */
-
-/* Use first bank for JFFS2, second bank contains U-Boot.
- *
- * Note: fake mtd_id's used, no linux mtd map file.
- */
-/*
-#define CONFIG_JFFS2_CMDLINE
-#define MTDIDS_DEFAULT "nor0=cpci405dt-0"
-#define MTDPARTS_DEFAULT "mtdparts=cpci405dt-0:-(jffs2)"
-*/
-
#if 0 /* Use NVRAM for environment variables */
/*-----------------------------------------------------------------------
* NVRAM organization
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
/*
* Internal Definitions
*
#define CONFIG_ACADIA 1 /* Board is Acadia */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_405EZ 1 /* Specifc 405EZ support*/
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME acadia
+#include "amcc-common.h"
+
/* Detect Acadia PLL input clock automatically via CPLD bit */
#define CONFIG_SYS_CLK_FREQ ((in8(CFG_CPLD_BASE + 0) == 0x0c) ? \
66666666 : 33333000)
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xfe000000
#define CFG_CPLD_BASE 0x80000000
#define CFG_NAND_ADDR 0xd0000000
#define CFG_USB_HOST 0xef603000 /* USB OHCI 1.1 controller */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1)
-#define CFG_MALLOC_LEN (512 * 1024)/* Reserve 512 kB for malloc() */
-
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer
*----------------------------------------------------------------------*/
*----------------------------------------------------------------------*/
#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
#define CFG_BASE_BAUD 691200
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
-
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
/*-----------------------------------------------------------------------
* Environment
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_DTT_LOW_TEMP -30
#define CFG_DTT_HYSTERESIS 3
-#if 0 /* test-only... */
-/*-----------------------------------------------------------------------
- * SPI stuff - Define to include SPI control
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SPI
-#endif
-
/*-----------------------------------------------------------------------
* Ethernet
*----------------------------------------------------------------------*/
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
-#define CONFIG_NET_MULTI 1
-#define CFG_RX_ETH_BUFFER 16 /* # of rx buffers & descriptors*/
#define CONFIG_HAS_ETH0 1
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define xstr(s) str(s)
-#define str(s) #s
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=acadia\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=acadia/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_PPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"kernel_addr=fff10000\0" \
"ramdisk_addr=fff20000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 acadia/u-boot.bin\0" \
- "update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
- "era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
- "cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "nload=tftp 200000 acadia/u-boot-nand.bin\0" \
- "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \
- "setenv filesize;saveenv\0" \
- "nupd=run nload nupdate\0" \
"kozio=bootm ffc60000\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_USB_OHCI
#define CONFIG_USB_STORAGE
#define CONFIG_SUPPORT_VFAT
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_USB
/*
#undef CONFIG_CMD_IMLS
#endif
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
/*-----------------------------------------------------------------------
* NAND FLASH
*----------------------------------------------------------------------*/
#define CFG_GPIO1_TSRL 0x00000000
#define CFG_GPIO1_TSRH 0x00000000
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
- #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#define CONFIG_LAST_STAGE_INIT 1 /* call last_stage_init() */
-#undef CFG_DRAM_TEST /* Disable-takes long time! */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
#define CONFIG_4xx_DCACHE /* Enable i- and d-cache */
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * Common configuration options for all AMCC boards
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __AMCC_COMMON_H
+#define __AMCC_COMMON_H
+
+#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CFG_MONITOR_BASE TEXT_BASE /* Start of U-Boot */
+#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1)
+#define CFG_MALLOC_LEN (1 << 20) /* Reserved for malloc */
+
+/*
+ * UART
+ */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SERIAL_MULTI
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
+
+/*
+ * I2C
+ */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#define CFG_I2C_SLAVE 0x7F
+
+/*
+ * Ethernet/EMAC/PHY
+ */
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_NET_MULTI
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#if defined(CONFIG_440)
+#define CFG_RX_ETH_BUFFER 32 /* number of eth rx buffers */
+#else
+#define CFG_RX_ETH_BUFFER 16 /* number of eth rx buffers */
+#endif
+
+/*
+ * Commands
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#if defined(CONFIG_440)
+#define CONFIG_CMD_CACHE
+#endif
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_EXTBDINFO /* To use extended board_into (bd_t) */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_CMDLINE_EDITING /* add command line history */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+#define CONFIG_LOOPW /* enable loopw command */
+#define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE /* include version env variable */
+#define CFG_CONSOLE_INFO_QUIET /* don't print console @ startup*/
+
+#define CFG_HUSH_PARSER /* Use the HUSH parser */
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_SUBNETMASK
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Internal Definitions
+ */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+
+/*
+ * Booting and default environment
+ */
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo"
+#define CONFIG_BOOTCOMMAND "run flash_self"
+
+/*
+ * Only very few boards have default console not on ttyS0 (like Taishan)
+ */
+#if !defined(CONFIG_USE_TTY)
+#define CONFIG_USE_TTY ttyS0
+#endif
+
+/*
+ * Only some 4xx PPC's are equipped with an FPU
+ */
+#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT)
+#define CONFIG_AMCC_DEF_ENV_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0"
+#else
+#define CONFIG_AMCC_DEF_ENV_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0"
+#endif
+
+/*
+ * Only some boards need to extend the bootargs by some additional
+ * parameters (like Makalu)
+ */
+#if !defined(CONFIG_ADDMISC)
+#define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs}\0"
+#endif
+
+#define xstr(s) str(s)
+#define str(s) #s
+
+/*
+ * General common environment variables shared on all AMCC eval boards
+ */
+#define CONFIG_AMCC_DEF_ENV \
+ "netdev=eth0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs}" \
+ " console=" xstr(CONFIG_USE_TTY) ",${baudrate}\0" \
+ CONFIG_ADDMISC \
+ "initrd_high=30000000\0" \
+ "kernel_addr_r=400000\0" \
+ "fdt_addr_r=800000\0" \
+ "hostname=" xstr(CONFIG_HOSTNAME) "\0" \
+ "bootfile=" xstr(CONFIG_HOSTNAME) "/uImage\0" \
+ CONFIG_AMCC_DEF_ENV_ROOTPATH
+
+/*
+ * Default environment for arch/powerpc booting
+ * for boards that are ported to arch/powerpc
+ */
+#define CONFIG_AMCC_DEF_ENV_POWERPC \
+ "flash_self=run ramargs addip addtty addmisc;" \
+ "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
+ "flash_nfs=run nfsargs addip addtty addmisc;" \
+ "bootm ${kernel_addr} - ${fdt_addr}\0" \
+ "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
+ "tftp ${fdt_addr_r} ${fdt_file}; " \
+ "run nfsargs addip addtty addmisc;" \
+ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
+ "fdt_file=" xstr(CONFIG_HOSTNAME) "/" xstr(CONFIG_HOSTNAME) ".dtb\0"
+
+/*
+ * Default environment for arch/ppc booting,
+ * for boards that are not ported to arch/powerpc yet
+ */
+#define CONFIG_AMCC_DEF_ENV_PPC \
+ "flash_self=run ramargs addip addtty addmisc;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "flash_nfs=run nfsargs addip addtty addmisc;" \
+ "bootm ${kernel_addr}\0" \
+ "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
+ "run nfsargs addip addtty addmisc;" \
+ "bootm ${kernel_addr_r}\0"
+
+/*
+ * Default environment for arch/ppc booting (old version),
+ * for boards that are ported to arch/ppc and arch/powerpc
+ */
+#define CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ "flash_self_old=run ramargs addip addtty addmisc;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "flash_nfs_old=run nfsargs addip addtty addmisc;" \
+ "bootm ${kernel_addr}\0" \
+ "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \
+ "run nfsargs addip addtty addmisc;" \
+ "bootm ${kernel_addr_r}\0"
+
+#define CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ "load=tftp 200000 " xstr(CONFIG_HOSTNAME) "/u-boot.bin\0" \
+ "update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
+ "era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
+ "cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \
+ "setenv filesize;saveenv\0" \
+ "upd=run load update\0" \
+
+#define CONFIG_AMCC_DEF_ENV_NAND_UPD \
+ "nload=tftp 200000 " xstr(CONFIG_HOSTNAME) "/u-boot-nand.bin\0" \
+ "nupdate=nand erase 0 100000;nand write 200000 0 100000;" \
+ "setenv filesize;saveenv\0" \
+ "nupd=run nload nupdate\0"
+
+#endif /* __AMCC_COMMON_H */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME bamboo
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */
#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/
#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
* Serial Port
*----------------------------------------------------------------------*/
#define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
/* define this if you want console on UART1 */
#undef CONFIG_UART1_CONSOLE
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* NVRAM/RTC
*
#define SPD_EEPROM_ADDRESS {CFG_SIMULATE_SPD_EEPROM, 0x50, 0x51}
#define CFG_MBYTES_SDRAM (64) /* 64MB fixed size for early-sdram-init */
#define CONFIG_PROG_SDRAM_TLB
-#undef CFG_DRAM_TEST
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_ENV_OFFSET 0x0
#endif /* CFG_ENV_IS_IN_EEPROM */
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=bamboo\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/bamboo/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"kernel_addr=fff00000\0" \
"ramdisk_addr=fff10000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/bamboo/u-boot.bin\0" \
- "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
- "cp.b 100000 fffa0000 60000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_HAS_ETH0
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
#define CONFIG_PHY1_ADDR 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#endif /* CONFIG_BAMBOO_NAND */
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI 1 /* required for netconsole */
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
#ifdef CONFIG_440EP
/* USB */
#define CONFIG_USB_OHCI
#define USB_2_0_DEVICE
#endif /*CONFIG_440EP*/
-
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_EXT2
#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_USB
#ifdef CONFIG_BAMBOO_NAND
#define CONFIG_CMD_NAND
#endif
-
#define CONFIG_SUPPORT_VFAT
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CONFIG_LYNXKDI 1 /* support kdi files */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
/*-----------------------------------------------------------------------
* PCI stuff
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_BUBINGA 1 /* ...on a BUBINGA board */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME bubinga
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
#endif
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=bubinga\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/bubinga/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_PPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fff80000\0" \
"ramdisk_addr=fff90000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/bubinga/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run net_nfs"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */
-#define CONFIG_NET_MULTI 1
-#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
#define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Bubinga */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SNTP
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
/*
* If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
* If CFG_405_UART_ERRATA_59, then UART divisor is 31.
#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
#define CFG_BASE_BAUD 691200
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*-----------------------------------------------------------------------
* I2C stuff
*-----------------------------------------------------------------------
*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES { 0x69 } /* avoid iprobe hangup (why?) */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_SRAM_BASE 0xFFF00000
#define CFG_FLASH_BASE 0xFFF80000
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
#define FPGA_REG1_OFFB_FLASH 0x02 /* Off board flash */
#define FPGA_REG1_SRAM_BOOT 0x01 /* SRAM at 0xFFF80000 not Flash */
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
/* This config file is used for Canyonlands (460EX) and Glacier (460GT) */
#ifndef CONFIG_CANYONLANDS
#define CONFIG_460GT 1 /* Specific PPC460GT */
+#define CONFIG_HOSTNAME glacier
#else
#define CONFIG_460EX 1 /* Specific PPC460EX */
+#define CONFIG_HOSTNAME canyonlands
#endif
#define CONFIG_440 1
#define CONFIG_4xx 1 /* ... PPC4xx family */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
+
#define CONFIG_SYS_CLK_FREQ 66666667 /* external freq to pll */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-
#define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
#define CFG_PCI_TARGBASE CFG_PCI_MEMBASE
#define CFG_AHB_BASE 0xE2000000 /* internal AHB peripherals */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc()*/
-
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in OCM)
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
#undef CONFIG_UART1_CONSOLE /* define this if you want console on UART1 */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_SPEED 400000 /* I2C speed */
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
* Ethernet
*----------------------------------------------------------------------*/
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
#define CONFIG_PHY1_ADDR 1
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH2
#define CONFIG_HAS_ETH3
#endif
-#define CONFIG_NET_MULTI 1
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_PHY_DYNAMIC_ANEG 1
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
/*-----------------------------------------------------------------------
* USB-OHCI
*----------------------------------------------------------------------*/
#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
#endif
-/*-----------------------------------------------------------------------
- * Default environment
- *----------------------------------------------------------------------*/
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-/* Setup some board specific values for the default environment variables */
-#ifdef CONFIG_CANYONLANDS
-#define CONFIG_HOSTNAME canyonlands
-#define CFG_BOOTFILE "bootfile=canyonlands/uImage\0"
-#define CFG_DTBFILE "fdt_file=canyonlands/canyonlands.dtb\0"
-#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0"
-#else
-#define CONFIG_HOSTNAME glacier
-#define CFG_BOOTFILE "bootfile=glacier/uImage\0"
-#define CFG_DTBFILE "fdt_file=glacier/glacier.dtb\0"
-#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0"
-#endif
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- CFG_BOOTFILE \
- CFG_DTBFILE \
- CFG_ROOTPATH \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; " \
- "run nfsargs addip addtty;" \
- "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
- "kernel_addr_r=400000\0" \
- "fdt_addr_r=800000\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"kernel_addr=fc000000\0" \
"fdt_addr=fc1e0000\0" \
"ramdisk_addr=fc200000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 ${hostname}/u-boot.bin\0" \
- "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
- "cp.b ${fileaddr} fffa0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "nload=tftp 200000 ${hostname}/u-boot-nand.bin\0" \
- "nupdate=nand erase 0 100000;nand write 200000 0 100000;" \
- "setenv filesize;saveenv\0" \
- "nupd=run nload nupdate\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SNTP
#ifdef CONFIG_460EX
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#define CONFIG_ISO_PARTITION
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
-#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#endif
-
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
}
#endif
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#undef CFG_DRAM_TEST /* Disable-takes long time! */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME ebony
+#include "amcc-common.h"
+
/*
* Define here the location of the environment variables (FLASH or NVRAM).
* Note: DENX encourages to use redundant environment in FLASH. NVRAM is only
*----------------------------------------------------------------------*/
#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xff800000 /* start of FLASH */
-#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */
#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/
-
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE 115200
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400}
/*-----------------------------------------------------------------------
* NVRAM/RTC
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_EEPROM_PAGE_WRITE_BITS 3
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=ebony\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/ebony/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=ff800000\0" \
"ramdisk_addr=ff810000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/ebony/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 8 /* PHY address */
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_PHY1_ADDR 9 /* EMAC1 PHY address */
-#define CONFIG_NET_MULTI 1
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SNTP
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_440SPE 1 /* Specifc SPe support */
-#undef CFG_DRAM_TEST /* Disable-takes long time */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME katmai
+#include "amcc-common.h"
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xff000000 /* start of FLASH */
#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */
#define CFG_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1)
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */
-
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in internal SRAM)
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#define CONFIG_SERIAL_MULTI 1
#undef CONFIG_UART1_CONSOLE
#undef CFG_EXT_SERIAL_CLOCK
-#define CONFIG_BAUDRATE 115200
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*-----------------------------------------------------------------------
* DDR SDRAM
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_I2C_CMD_TREE
*----------------------------------------------------------------------*/
#define CFG_ENV_IS_IN_FLASH 1 /* Environment uses flash */
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define xstr(s) str(s)
-#define str(s) #s
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=katmai\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "net_nfs_fdt=tftp 200000 ${bootfile};" \
- "tftp ${fdt_addr} ${fdt_file};" \
- "run nfsargs addip addtty;" \
- "bootm 200000 - ${fdt_addr}\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=katmai/uImage\0" \
- "fdt_file=katmai/katmai.dtb\0" \
- "fdt_addr=400000\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fff10000\0" \
"ramdisk_addr=fff20000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 katmai/u-boot.bin\0" \
- "update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
- "era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
- "cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
"kozio=bootm ffc60000\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP:RP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SNTP
#define CONFIG_IBM_EMAC4_V4 1 /* 440SPe has this EMAC version */
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
#define CONFIG_HAS_ETH0
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_RESET_DELAY 1000
#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* needed for NetConsole */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
-#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */
/*-----------------------------------------------------------------------
* FLASH related
#define CFG_GPIO_TCR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF)
#define CFG_GPIO_ODR 0
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
/*
+ * Copyright (c) 2008 Nuovation System Designs, LLC
+ * Grant Erickson <gerickson@nuovations.com>
+ *
* (C) Copyright 2007
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
#define CONFIG_405EX 1 /* Specifc 405EX support*/
#define CONFIG_SYS_CLK_FREQ 33333333 /* ext frequency to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME kilauea
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
#define CONFIG_BOARD_EMAC_COUNT
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xFC000000
#define CFG_NAND_ADDR 0xF8000000
#define CFG_FPGA_BASE 0xF0000000
#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */
-#define CFG_MONITOR_BASE (TEXT_BASE)
/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer
- *----------------------------------------------------------------------*/
-#define CFG_INIT_RAM_ADDR 0x02000000 /* inside of SDRAM */
-#define CFG_INIT_RAM_END (4 << 10)
+ * Initial RAM & Stack Pointer Configuration Options
+ *
+ * There are traditionally three options for the primordial
+ * (i.e. initial) stack usage on the 405-series:
+ *
+ * 1) On-chip Memory (OCM) (i.e. SRAM)
+ * 2) Data cache
+ * 3) SDRAM
+ *
+ * For the 405EX(r), there is no OCM, so we are left with (2) or (3)
+ * the latter of which is less than desireable since it requires
+ * setting up the SDRAM and ECC in assembly code.
+ *
+ * To use (2), define 'CFG_INIT_DCACHE_CS' to be an unused chip
+ * select on the External Bus Controller (EBC) and then select a
+ * value for 'CFG_INIT_RAM_ADDR' outside of the range of valid,
+ * physical SDRAM. Otherwise, undefine 'CFG_INIT_DCACHE_CS' and
+ * select a value for 'CFG_INIT_RAM_ADDR' within the range of valid,
+ * physical SDRAM to use (3).
+ *-----------------------------------------------------------------------*/
+
+#define CFG_INIT_DCACHE_CS 4
+
+#if defined(CFG_INIT_DCACHE_CS)
+#define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + ( 1 << 30)) /* 1 GiB */
+#else
+#define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + (32 << 20)) /* 32 MiB */
+#endif /* defined(CFG_INIT_DCACHE_CS) */
+
+#define CFG_INIT_RAM_END (4 << 10) /* 4 KiB */
#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-/* reserve some memory for POST and BOOT limit info */
-#define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - 16)
-/* extra data in init-ram */
-#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4)
-#define CFG_POST_MAGIC (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 8)
-#define CFG_POST_VAL (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 12)
-#define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR /* for commproc.c */
+/*
+ * If the data cache is being used for the primordial stack and global
+ * data area, the POST word must be placed somewhere else. The General
+ * Purpose Timer (GPT) is unused by u-boot and the kernel and preserves
+ * its compare and mask register contents across reset, so it is used
+ * for the POST word.
+ */
+
+#if defined(CFG_INIT_DCACHE_CS)
+# define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+# define CFG_POST_ALT_WORD_ADDR (CFG_PERIPHERAL_BASE + GPT0_COMP6)
+#else
+# define CFG_INIT_EXTRA_SIZE 16
+# define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - CFG_INIT_EXTRA_SIZE)
+# define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4)
+# define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR
+#endif /* defined(CFG_INIT_DCACHE_CS) */
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
/* define this if you want console on UART1 */
#undef CONFIG_UART1_CONSOLE
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
* This NAND U-Boot (NUB) is a special U-Boot version which can be started
* from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
*
- * On 440EPx the SPL is copied to SDRAM before the NAND controller is
- * set up. While still running from cache, I experienced problems accessing
- * the NAND controller. sr - 2006-08-25
+ * On 405EX the SPL is copied to SDRAM before the NAND controller is
+ * set up. While still running from location 0xfffff000...0xffffffff the
+ * NAND controller cannot be accessed since it is attached to CS0 too.
*/
#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
*----------------------------------------------------------------------*/
#define CFG_MBYTES_SDRAM (256) /* 256MB */
+#define CFG_SDRAM0_MB0CF_BASE (( 0 << 20) + CFG_SDRAM_BASE)
+
+/* DDR1/2 SDRAM Device Control Register Data Values */
+#define CFG_SDRAM0_MB0CF ((CFG_SDRAM0_MB0CF_BASE >> 3) | \
+ SDRAM_RXBAS_SDSZ_256MB | \
+ SDRAM_RXBAS_SDAM_MODE7 | \
+ SDRAM_RXBAS_SDBE_ENABLE)
+#define CFG_SDRAM0_MB1CF SDRAM_RXBAS_SDBE_DISABLE
+#define CFG_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE
+#define CFG_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE
+#define CFG_SDRAM0_MCOPT1 0x04322000
+#define CFG_SDRAM0_MCOPT2 0x00000000
+#define CFG_SDRAM0_MODT0 0x01800000
+#define CFG_SDRAM0_MODT1 0x00000000
+#define CFG_SDRAM0_CODT 0x0080f837
+#define CFG_SDRAM0_RTR 0x06180000
+#define CFG_SDRAM0_INITPLR0 0xa8380000
+#define CFG_SDRAM0_INITPLR1 0x81900400
+#define CFG_SDRAM0_INITPLR2 0x81020000
+#define CFG_SDRAM0_INITPLR3 0x81030000
+#define CFG_SDRAM0_INITPLR4 0x81010404
+#define CFG_SDRAM0_INITPLR5 0x81000542
+#define CFG_SDRAM0_INITPLR6 0x81900400
+#define CFG_SDRAM0_INITPLR7 0x8D080000
+#define CFG_SDRAM0_INITPLR8 0x8D080000
+#define CFG_SDRAM0_INITPLR9 0x8D080000
+#define CFG_SDRAM0_INITPLR10 0x8D080000
+#define CFG_SDRAM0_INITPLR11 0x81000442
+#define CFG_SDRAM0_INITPLR12 0x81010780
+#define CFG_SDRAM0_INITPLR13 0x81010400
+#define CFG_SDRAM0_INITPLR14 0x00000000
+#define CFG_SDRAM0_INITPLR15 0x00000000
+#define CFG_SDRAM0_RQDC 0x80000038
+#define CFG_SDRAM0_RFDC 0x00000209
+#define CFG_SDRAM0_RDCC 0x40000000
+#define CFG_SDRAM0_DLCR 0x030000a5
+#define CFG_SDRAM0_CLKTR 0x80000000
+#define CFG_SDRAM0_WRDTR 0x00000000
+#define CFG_SDRAM0_SDTR1 0x80201000
+#define CFG_SDRAM0_SDTR2 0x32204232
+#define CFG_SDRAM0_SDTR3 0x080b0d1a
+#define CFG_SDRAM0_MMODE 0x00000442
+#define CFG_SDRAM0_MEMODE 0x00000404
+
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
#define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */
*----------------------------------------------------------------------*/
#define CONFIG_M88E1111_PHY 1
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_HAS_ETH0 1
-#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR 2
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"logversion=2\0" \
- "netdev=eth0\0" \
- "hostname=kilauea\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_self_old=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- "flash_nfs_old=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \
- "run nfsargs addip addtty;bootm ${kernel_addr_r}\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; " \
- "run nfsargs addip addtty;" \
- "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=kilauea/uImage\0" \
- "fdt_file=kilauea/kilauea.dtb\0" \
- "kernel_addr_r=400000\0" \
- "fdt_addr_r=800000\0" \
"kernel_addr=fc000000\0" \
"fdt_addr=fc1e0000\0" \
"ramdisk_addr=fc200000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 kilauea/u-boot.bin\0" \
- "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
- "cp.b ${fileaddr} fffa0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "nload=tftp 200000 kilauea/u-boot-nand.bin\0" \
- "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \
- "setenv filesize;saveenv\0" \
- "nupd=run nload nupdate\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
#define CONFIG_CMD_LOG
-#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SNTP
/* POST support */
-#define CONFIG_POST (CFG_POST_MEMORY | \
- CFG_POST_CACHE | \
+#define CONFIG_POST (CFG_POST_CACHE | \
CFG_POST_CPU | \
CFG_POST_ETHER | \
CFG_POST_I2C | \
#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
/* base address of inbound PCIe window */
#define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
/* Memory Bank 2 (FPGA) initialization */
#define CFG_EBC_PB2AP 0x9400C800
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0x800,BS=1MB,BU=R/W,BW=8bit */
+#define CFG_EBC_PB2CR (CFG_FPGA_BASE | 0x18000)
#define CFG_EBC_CFG 0x7FC00000 /* EBC0_CFG */
} \
}
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
/*-----------------------------------------------------------------------
* Some Kilauea stuff..., mainly fpga registers
*/
#define CFG_FPGA_USER_LED0 0x00000200
#define CFG_FPGA_USER_LED1 0x00000100
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_440 1
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME luan
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc */
-#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
-#define CFG_SDRAM_BASE 0x00000000 /* MUST be zero */
-
#define CFG_LARGE_FLASH 0xffc00000 /* 4MB flash address CS0 */
#define CFG_SMALL_FLASH 0xff900000 /* 1MB flash address CS2 */
#define CFG_SRAM_BASE 0xff800000 /* 1MB SRAM address CS2 */
#define CFG_FLASH_BASE CFG_SMALL_FLASH
#endif
-#undef CFG_DRAM_TEST
#if CFG_SRAM_BASE
#define CFG_KBYTES_SDRAM 1024*2
#else
* Serial Port
*----------------------------------------------------------------------*/
#define CFG_EXT_SERIAL_CLOCK 11059200 /* external 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#undef CONFIG_SERIAL_MULTI
#undef CONFIG_UART1_CONSOLE /* define if you want console on UART1 */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_EEPROM_PAGE_WRITE_BITS 3
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=luan\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
- "addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm $(kernel_addr)\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm $(kernel_addr) $(ramdisk_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/luan/uImage\0" \
+/*
+ * Default environment variables
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_PPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fc000000\0" \
"ramdisk_addr=fc100000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/luan/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_HAS_ETH0
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1
#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* needed for NetConsole */
-
#ifdef DEBUG
#define CONFIG_PANIC_HANG
#else
#endif
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#undef CONFIG_LYNXKDI /* support kdi files */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
#endif
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
/*
+ * Copyright (c) 2008 Nuovation System Designs, LLC
+ * Grant Erickson <gerickson@nuovations.com>
+ *
* (C) Copyright 2007-2008
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
#define CONFIG_405EX 1 /* Specifc 405EX support*/
#define CONFIG_SYS_CLK_FREQ 33330000 /* ext frequency to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME makalu
+#define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0"
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xFC000000
#define CFG_FPGA_BASE 0xF0000000
#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */
-#define CFG_MONITOR_BASE (TEXT_BASE)
/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer
- *----------------------------------------------------------------------*/
-#define CFG_INIT_RAM_ADDR 0x02000000 /* inside of SDRAM */
-#define CFG_INIT_RAM_END (4 << 10)
+ * Initial RAM & Stack Pointer Configuration Options
+ *
+ * There are traditionally three options for the primordial
+ * (i.e. initial) stack usage on the 405-series:
+ *
+ * 1) On-chip Memory (OCM) (i.e. SRAM)
+ * 2) Data cache
+ * 3) SDRAM
+ *
+ * For the 405EX(r), there is no OCM, so we are left with (2) or (3)
+ * the latter of which is less than desireable since it requires
+ * setting up the SDRAM and ECC in assembly code.
+ *
+ * To use (2), define 'CFG_INIT_DCACHE_CS' to be an unused chip
+ * select on the External Bus Controller (EBC) and then select a
+ * value for 'CFG_INIT_RAM_ADDR' outside of the range of valid,
+ * physical SDRAM. Otherwise, undefine 'CFG_INIT_DCACHE_CS' and
+ * select a value for 'CFG_INIT_RAM_ADDR' within the range of valid,
+ * physical SDRAM to use (3).
+ *-----------------------------------------------------------------------*/
+
+#define CFG_INIT_DCACHE_CS 4
+
+#if defined(CFG_INIT_DCACHE_CS)
+#define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + ( 1 << 30)) /* 1 GiB */
+#else
+#define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + (32 << 20)) /* 32 MiB */
+#endif /* defined(CFG_INIT_DCACHE_CS) */
+
+#define CFG_INIT_RAM_END (4 << 10) /* 4 KiB */
#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-/* reserve some memory for POST and BOOT limit info */
-#define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - 16)
-/* extra data in init-ram */
-#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4)
-#define CFG_POST_MAGIC (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 8)
-#define CFG_POST_VAL (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 12)
-#define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR /* for commproc.c */
+/*
+ * If the data cache is being used for the primordial stack and global
+ * data area, the POST word must be placed somewhere else. The General
+ * Purpose Timer (GPT) is unused by u-boot and the kernel and preserves
+ * its compare and mask register contents across reset, so it is used
+ * for the POST word.
+ */
+
+#if defined(CFG_INIT_DCACHE_CS)
+# define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+# define CFG_POST_ALT_WORD_ADDR (CFG_PERIPHERAL_BASE + GPT0_COMP6)
+#else
+# define CFG_INIT_EXTRA_SIZE 16
+# define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - CFG_INIT_EXTRA_SIZE)
+# define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4)
+# define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR
+#endif /* defined(CFG_INIT_DCACHE_CS) */
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#undef CFG_EXT_SERIAL_CLOCK /* no ext. clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
/* define this if you want console on UART1 */
#undef CONFIG_UART1_CONSOLE
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
-#define CFG_MBYTES_SDRAM 256
+#define CFG_MBYTES_SDRAM (256) /* 256MB */
+
+#define CFG_SDRAM0_MB0CF_BASE (( 0 << 20) + CFG_SDRAM_BASE)
+#define CFG_SDRAM0_MB1CF_BASE ((128 << 20) + CFG_SDRAM_BASE)
+
+/* DDR1/2 SDRAM Device Control Register Data Values */
+#define CFG_SDRAM0_MB0CF ((CFG_SDRAM0_MB0CF_BASE >> 3) | \
+ SDRAM_RXBAS_SDSZ_128MB | \
+ SDRAM_RXBAS_SDAM_MODE2 | \
+ SDRAM_RXBAS_SDBE_ENABLE)
+#define CFG_SDRAM0_MB1CF ((CFG_SDRAM0_MB1CF_BASE >> 3) | \
+ SDRAM_RXBAS_SDSZ_128MB | \
+ SDRAM_RXBAS_SDAM_MODE2 | \
+ SDRAM_RXBAS_SDBE_ENABLE)
+#define CFG_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE
+#define CFG_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE
+#define CFG_SDRAM0_MCOPT1 0x04322000
+#define CFG_SDRAM0_MCOPT2 0x00000000
+#define CFG_SDRAM0_MODT0 0x01800000
+#define CFG_SDRAM0_MODT1 0x00000000
+#define CFG_SDRAM0_CODT 0x0080f837
+#define CFG_SDRAM0_RTR 0x06180000
+#define CFG_SDRAM0_INITPLR0 0xa8380000
+#define CFG_SDRAM0_INITPLR1 0x81900400
+#define CFG_SDRAM0_INITPLR2 0x81020000
+#define CFG_SDRAM0_INITPLR3 0x81030000
+#define CFG_SDRAM0_INITPLR4 0x81010404
+#define CFG_SDRAM0_INITPLR5 0x81000542
+#define CFG_SDRAM0_INITPLR6 0x81900400
+#define CFG_SDRAM0_INITPLR7 0x8D080000
+#define CFG_SDRAM0_INITPLR8 0x8D080000
+#define CFG_SDRAM0_INITPLR9 0x8D080000
+#define CFG_SDRAM0_INITPLR10 0x8D080000
+#define CFG_SDRAM0_INITPLR11 0x81000442
+#define CFG_SDRAM0_INITPLR12 0x81010780
+#define CFG_SDRAM0_INITPLR13 0x81010400
+#define CFG_SDRAM0_INITPLR14 0x00000000
+#define CFG_SDRAM0_INITPLR15 0x00000000
+#define CFG_SDRAM0_RQDC 0x80000038
+#define CFG_SDRAM0_RFDC 0x00000209
+#define CFG_SDRAM0_RDCC 0x40000000
+#define CFG_SDRAM0_DLCR 0x030000a5
+#define CFG_SDRAM0_CLKTR 0x80000000
+#define CFG_SDRAM0_WRDTR 0x00000000
+#define CFG_SDRAM0_SDTR1 0x80201000
+#define CFG_SDRAM0_SDTR2 0x32204232
+#define CFG_SDRAM0_SDTR3 0x080b0d1a
+#define CFG_SDRAM0_MMODE 0x00000442
+#define CFG_SDRAM0_MEMODE 0x00000404
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
#define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */
*----------------------------------------------------------------------*/
#define CONFIG_M88E1111_PHY 1
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 6 /* PHY address, See schematics */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_HAS_ETH0 1
-#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR 0
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "logversion=2\0" \
- "netdev=eth0\0" \
- "hostname=makalu\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0" \
- "flash_self_old=run ramargs addip addtty addmisc;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "flash_self=run ramargs addip addtty addmisc;" \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- "flash_nfs_old=run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr}\0" \
- "flash_nfs=run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \
- "run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr_r}\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; " \
- "run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=makalu/uImage\0" \
- "fdt_file=makalu/makalu.dtb\0" \
- "kernel_addr_r=400000\0" \
- "fdt_addr_r=800000\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fc000000\0" \
"fdt_addr=fc1e0000\0" \
"ramdisk_addr=fc200000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 makalu/u-boot.bin\0" \
- "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
- "cp.b ${fileaddr} fffa0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
#define CONFIG_CMD_LOG
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SNTP
/* POST support */
-#define CONFIG_POST (CFG_POST_MEMORY | \
- CFG_POST_CACHE | \
+#define CONFIG_POST (CFG_POST_CACHE | \
CFG_POST_CPU | \
CFG_POST_ETHER | \
CFG_POST_I2C | \
#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
/* base address of inbound PCIe window */
#define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
#define CFG_GPIO_PCIE_CLKREQ 27
#define CFG_GPIO_PCIE_WAKE 28
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#undef CFG_DRAM_TEST /* Disable-takes long time! */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME ocotea
+#include "amcc-common.h"
+
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xff800000 /* start of FLASH */
-#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */
#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */
#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/
-
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE 115200
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*-----------------------------------------------------------------------
* Environment
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_EEPROM_PAGE_WRITE_BITS 3
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=ocotea\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/ocotea/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_PPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fff00000\0" \
"ramdisk_addr=fff10000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/ocotea/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_NET_MULTI 1
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
#define CONFIG_PHY1_ADDR 2
#define CONFIG_PHY2_ADDR 0x10
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_RESET_DELAY 1000
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SNTP
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
/* This config file is used for Sequoia (440EPx) and Rainier (440GRx) */
#ifndef CONFIG_RAINIER
#define CONFIG_440EPX 1 /* Specific PPC440EPx */
+#define CONFIG_HOSTNAME sequoia
#else
#define CONFIG_440GRX 1 /* Specific PPC440GRx */
+#define CONFIG_HOSTNAME rainier
#endif
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
+
/* Detect Sequoia PLL input clock automatically via CPLD bit */
#define CONFIG_SYS_CLK_FREQ ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \
33333333 : 33000000)
* Base addresses -- Note these are effective addresses where the actual
* resources get mapped (not physical addresses).
*/
-#ifndef CONFIG_VIDEO
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kiB for Monitor */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kiB for malloc() */
-#else
-#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
-#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */
-#endif
-
#define CFG_TLB_FOR_BOOT_FLASH 0x0003
#define CFG_BOOT_BASE_ADDR 0xf0000000
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
-#define CFG_MONITOR_BASE TEXT_BASE
#define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */
#define CFG_OCM_BASE 0xe0010000 /* ocm */
#define CFG_OCM_DATA_ADDR CFG_OCM_BASE
* Serial Port
*/
#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
/* define this if you want console on UART1 */
#undef CONFIG_UART1_CONSOLE
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*
* Environment
*/
/*
* I2C
*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_DTT_LOW_TEMP -30
#define CFG_DTT_HYSTERESIS 3
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-/* Setup some board specific values for the default environment variables */
-#ifndef CONFIG_RAINIER
-#define CONFIG_HOSTNAME sequoia
-#define CFG_BOOTFILE "bootfile=sequoia/uImage\0"
-#define CFG_DTBFILE "fdt_file=sequoia/sequoia.dtb\0"
-#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0"
-#else
-#define CONFIG_HOSTNAME rainier
-#define CFG_BOOTFILE "bootfile=rainier/uImage\0"
-#define CFG_DTBFILE "fdt_file=rainier/rainier.dtb\0"
-#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0"
-#endif
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- CFG_BOOTFILE \
- CFG_ROOTPATH \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "addmisc=setenv bootargs ${bootargs}\0" \
- "flash_nfs=run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty addmisc;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};" \
- "run nfsargs addip addtty addmisc;" \
- "bootm\0" \
- "fdt_file=sequoia/sequoia.dtb\0" \
- "fdt_addr=400000\0" \
- "net_nfs_fdt=tftp 200000 ${bootfile};" \
- "tftp ${fdt_addr} ${fdt_file};" \
- "run nfsargs addip addtty addmisc;" \
- "bootm 200000 - ${fdt_addr}\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"kernel_addr=FC000000\0" \
"ramdisk_addr=FC180000\0" \
- "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \
- "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \
- "cp.b 200000 FFFA0000 60000\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_M88E1111_PHY 1
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_HAS_ETH0
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx */
- /* buffers & descriptors */
-#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR 1
#define CONFIG_ISO_PARTITION
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#ifdef CONFIG_440EPX
#define CONFIG_SUPPORT_VFAT
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
- /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*
* PCI stuff
*/
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data have to be in the
- * first 8 MB of memory, since this is the maximum mapped by the Linux kernel
- * during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
/*
* External Bus Controller (EBC) Setup
*/
} \
}
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#ifdef CONFIG_VIDEO
#define CONFIG_BIOSEMU /* x86 bios emulator for vga bios */
#define CONFIG_ATI_RADEON_FB /* use radeon framebuffer driver */
#define CONFIG_4xx 1 /* member of PPC4xx family */
#define CONFIG_TAIHU 1 /* on a taihu board */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME taihu
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f */
#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-#define CONFIG_ENV_OVERWRITE 1
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "bootfile=/tftpboot/taihu/uImage\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "netdev=eth0\0" \
- "hostname=taihu\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
+/*
+ * Default environment variables
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_PPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=FC000000\0" \
"ramdisk_addr=FC180000\0" \
- "load=tftp 200000 /tftpboot/taihu/u-boot.bin\0" \
- "update=protect off FFFC0000 FFFFFFFF;era FFFC0000 FFFFFFFF;" \
- "cp.b 200000 FFFC0000 40000\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0x14 /* PHY address */
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_PHY1_ADDR 0x10 /* EMAC1 PHY address */
-#define CONFIG_NET_MULTI 1
-#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */
#define CONFIG_PHY_RESET 1
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SPI
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
#undef CONFIG_SPD_EEPROM /* use SPD EEPROM for setup */
#define CFG_SDRAM_SIZE_PER_BANK 0x04000000 /* 64MB */
#define CFG_SDRAM_BANKS 2
#define CFG_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */
#define CFG_SDRAM_tRFC 66 /* Auto refresh period */
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* print buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
/*
* If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
* If CFG_405_UART_ERRATA_59, then UART divisor is 31.
#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
#define CFG_BASE_BAUD 691200
-
-#define CONFIG_BAUDRATE 115200
-
#define CONFIG_UART1_CONSOLE 1
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
/*-----------------------------------------------------------------------
* I2C stuff
*-----------------------------------------------------------------------
*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES { 0x69 } /* avoid iprobe hangup (why?) */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xFFE00000
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-
#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CPLD_REG0_ADDR 0x50100000
#define CPLD_REG1_ADDR 0x50100001
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
#endif /* __CONFIG_H */
#define CONFIG_440GX 1 /* Specifc GX support */
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
-#undef CFG_DRAM_TEST /* Disable-takes long time! */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME taishan
+#define CONFIG_USE_TTY ttyS1
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
-#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */
#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */
#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/
-#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc*/
-
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#define CONFIG_UART1_CONSOLE 1 /* use of UART1 as console */
-#define CONFIG_SERIAL_MULTI 1 /* enable serial multi support */
#define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE 115200
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*-----------------------------------------------------------------------
* Environment
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#undef CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR 0x50
#define CFG_DTT_LOW_TEMP -30
#define CFG_DTT_HYSTERESIS 3
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=taishan\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/taishan/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fc000000\0" \
"ramdisk_addr=fc180000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/taishan/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "fixedip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
- "$(gatewayip):$(netmask):$(hostname):$(netdev):off panic=1\0" \
- "dhcp=setenv bootargs $(bootargs) ip=dhcp\0" \
"kozio=bootm 0xffe00000\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*-----------------------------------------------------------------------
* Networking
*----------------------------------------------------------------------*/
#define CONFIG_EMAC_NR_START 2 /* start with EMAC 2 (skip 0&1) */
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_NET_MULTI 1
#define CONFIG_PHY_ADDR 0xff /* no phy on EMAC0 */
#define CONFIG_PHY1_ADDR 0xff /* no phy on EMAC1 */
#define CONFIG_PHY2_ADDR 0x1
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_RESET_DELAY 1000
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* PCI stuff
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_WALNUT 1 /* ...on a WALNUT board */
/* ...and on a SYCAMORE board */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME walnut
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=walnut\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/walnut/uImage\0" \
+/*
+ * Default environment variables
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fff80000\0" \
"ramdisk_addr=fff80000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/walnut/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run net_nfs"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
-
-#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
#define CONFIG_HAS_ETH0 1
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* needed for NetConsole */
-
#define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Walnut */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SNTP
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
/*
* If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
* If CFG_405_UART_ERRATA_59, then UART divisor is 31.
#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
#define CFG_BASE_BAUD 691200
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*-----------------------------------------------------------------------
* I2C stuff
*-----------------------------------------------------------------------
*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xFFF80000
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
/*
* Define here the location of the environment variables (FLASH or NVRAM).
#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
#endif
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
/*-----------------------------------------------------------------------
* FLASH organization
*/
*/
#define SPD_EEPROM_ADDRESS 0x50
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
#define CONFIG_BOARD_RESET 1 /* call board_reset() */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/
#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
* Serial Port
*----------------------------------------------------------------------*/
#define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
/*define this if you want console on UART1*/
#undef CONFIG_UART1_CONSOLE
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_DTT_LOW_TEMP -30
#define CFG_DTT_HYSTERESIS 3
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-/* Setup some board specific values for the default environment variables */
-#ifndef CONFIG_YELLOWSTONE
-#define CONFIG_HOSTNAME yosemite
-#define CFG_BOOTFILE "bootfile=/tftpboot/yosemite/uImage\0"
-#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0"
-#else
-#define CONFIG_HOSTNAME yellowstone
-#define CFG_BOOTFILE "bootfile=/tftpboot/yellowstone/uImage\0"
-#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0"
-#endif
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- CFG_BOOTFILE \
- CFG_ROOTPATH \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "bootfile=/tftpboot/${hostname}/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fc000000\0" \
"ramdisk_addr=fc180000\0" \
- "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \
- "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \
- "cp.b 200000 fff80000 80000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_NET_MULTI 1 /* required for netconsole */
-#define CONFIG_PHY1_ADDR 3
#define CONFIG_HAS_ETH0 1 /* add support for "ethaddr" */
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
-
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_PHY1_ADDR 3
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_HW_WATCHDOG /* watchdog */
#endif
-
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SDRAM
#ifdef CONFIG_440EP
#define CONFIG_CMD_USB
#define CONFIG_CMD_EXT2
#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CONFIG_LYNXKDI 1 /* support kdi files */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
#define CFG_BCSR5_PCI66EN 0x80
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_440SPE 1 /* Specifc SPe support */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#undef CFG_DRAM_TEST /* Disable-takes long time */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
#define EXTCLK_33_33 33333333
#define EXTCLK_66_66 66666666
#define EXTCLK_50 50000000
#define EXTCLK_83 83333333
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME yucca
+#include "amcc-common.h"
+
#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
#undef CONFIG_SHOW_BOOT_PROGRESS
#undef CONFIG_STRESS
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */
-#define CFG_MONITOR_BASE 0xfffb0000 /* start of monitor */
#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */
#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
-#define CFG_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Mon */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */
-
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#define CONFIG_SERIAL_MULTI 1
#undef CONFIG_UART1_CONSOLE
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#undef CFG_EXT_SERIAL_CLOCK
/* #define CFG_EXT_SERIAL_CLOCK (1843200 * 6) */ /* Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE 115200
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define IIC0_BOOTPROM_ADDR 0x50
#define IIC0_ALT_BOOTPROM_ADDR 0x54
#undef CFG_ENV_IS_IN_EEPROM /* ... not in EEPROM */
#define CONFIG_ENV_OVERWRITE 1
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=yucca\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=yucca/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_PPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=E7F10000\0" \
"ramdisk_addr=E7F20000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 yuca/u-boot.bin\0" \
- "update=protect off 2:4-7;era 2:4-7;" \
- "cp.b ${fileaddr} FFFB0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:EP:EP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
-
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
-#undef CONFIG_NET_MULTI
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
#define CONFIG_HAS_ETH0
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_RESET_DELAY 1000
#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* needed for NetConsole */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* FLASH related
/* Support for Intel 82557/82559/82559ER chips. */
#define CONFIG_EEPRO100
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
/* FB Divisor selection */
#define FPGA_FB_DIV_6 6
#define FPGA_FB_DIV_10 10
#define PERIOD_33_33MHZ 30000 /* 30ns */
#define PERIOD_25_00MHZ 40000 /* 40ns */
-/*---------------------------------------------------------------------------*/
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#ifndef __PPC405_H__
#define __PPC405_H__
+/* Define bits and masks for real-mode storage attribute control registers */
+#define PPC_128MB_SACR_BIT(addr) ((addr) >> 27)
+#define PPC_128MB_SACR_VALUE(addr) PPC_REG_VAL(PPC_128MB_SACR_BIT(addr),1)
+
#ifndef CONFIG_IOP480
#define CFG_DCACHE_SIZE (16 << 10) /* For AMCC 405 CPUs */
#else
#endif /* defined(CONFIG_405EZ) */
/******************************************************************************
- * SDRAM Controller
- ******************************************************************************/
- /* values for memcfga register - indirect addressing of these regs */
-#ifndef CONFIG_405EP
- #define mem_besra 0x00 /* bus error syndrome reg a */
- #define mem_besrsa 0x04 /* bus error syndrome reg set a */
- #define mem_besrb 0x08 /* bus error syndrome reg b */
- #define mem_besrsb 0x0c /* bus error syndrome reg set b */
- #define mem_bear 0x10 /* bus error address reg */
-#endif
- #define mem_mcopt1 0x20 /* memory controller options 1 */
- #define mem_status 0x24 /* memory status */
- #define mem_rtr 0x30 /* refresh timer reg */
- #define mem_pmit 0x34 /* power management idle timer */
- #define mem_mb0cf 0x40 /* memory bank 0 configuration */
- #define mem_mb1cf 0x44 /* memory bank 1 configuration */
-#ifndef CONFIG_405EP
- #define mem_mb2cf 0x48 /* memory bank 2 configuration */
- #define mem_mb3cf 0x4c /* memory bank 3 configuration */
-#endif
- #define mem_sdtr1 0x80 /* timing reg 1 */
-#ifndef CONFIG_405EP
- #define mem_ecccf 0x94 /* ECC configuration */
- #define mem_eccerr 0x98 /* ECC error status */
-#endif
+ * External Bus Controller (EBC)
+ *****************************************************************************/
+
+/* Bank Configuration Register */
+#define EBC_BXCR_BAS_MASK PPC_REG_VAL(11, 0xFFF)
+#define EBC_BXCR_BAS_ENCODE(n) (((static_cast(unsigned long, n)) & \
+ EBC_BXCR_BAS_MASK) << 0)
+#define EBC_BXCR_BS_MASK PPC_REG_VAL(14, 0x7)
+#define EBC_BXCR_BS_1MB PPC_REG_VAL(14, 0x0)
+#define EBC_BXCR_BS_2MB PPC_REG_VAL(14, 0x1)
+#define EBC_BXCR_BS_4MB PPC_REG_VAL(14, 0x2)
+#define EBC_BXCR_BS_8MB PPC_REG_VAL(14, 0x3)
+#define EBC_BXCR_BS_16MB PPC_REG_VAL(14, 0x4)
+#define EBC_BXCR_BS_32MB PPC_REG_VAL(14, 0x5)
+#define EBC_BXCR_BS_64MB PPC_REG_VAL(14, 0x6)
+#define EBC_BXCR_BS_128MB PPC_REG_VAL(14, 0x7)
+#define EBC_BXCR_BU_MASK PPC_REG_VAL(16, 0x3)
+#define EBC_BXCR_BU_NONE PPC_REG_VAL(16, 0x0)
+#define EBC_BXCR_BU_R PPC_REG_VAL(16, 0x1)
+#define EBC_BXCR_BU_W PPC_REG_VAL(16, 0x2)
+#define EBC_BXCR_BU_RW PPC_REG_VAL(16, 0x3)
+#define EBC_BXCR_BW_MASK PPC_REG_VAL(18, 0x3)
+#define EBC_BXCR_BW_8BIT PPC_REG_VAL(18, 0x0)
+#define EBC_BXCR_BW_16BIT PPC_REG_VAL(18, 0x1)
+#define EBC_BXCR_BW_32BIT PPC_REG_VAL(18, 0x3)
+
+/* Bank Access Parameter Register */
+#define EBC_BXAP_BME_ENABLED PPC_REG_VAL(0, 0x1)
+#define EBC_BXAP_BME_DISABLED PPC_REG_VAL(0, 0x0)
+#define EBC_BXAP_TWT_ENCODE(n) PPC_REG_VAL(8, \
+ (static_cast(unsigned long, n)) \
+ & 0xFF)
+#define EBC_BXAP_FWT_ENCODE(n) PPC_REG_VAL(5, \
+ (static_cast(unsigned long, n)) \
+ & 0x1F)
+#define EBC_BXAP_BWT_ENCODE(n) PPC_REG_VAL(8, \
+ (static_cast(unsigned long, n)) \
+ & 0x7)
+#define EBC_BXAP_BCE_DISABLE PPC_REG_VAL(9, 0x0)
+#define EBC_BXAP_BCE_ENABLE PPC_REG_VAL(9, 0x1)
+#define EBC_BXAP_BCT_MASK PPC_REG_VAL(11, 0x3)
+#define EBC_BXAP_BCT_2TRANS PPC_REG_VAL(11, 0x0)
+#define EBC_BXAP_BCT_4TRANS PPC_REG_VAL(11, 0x1)
+#define EBC_BXAP_BCT_8TRANS PPC_REG_VAL(11, 0x2)
+#define EBC_BXAP_BCT_16TRANS PPC_REG_VAL(11, 0x3)
+#define EBC_BXAP_CSN_ENCODE(n) PPC_REG_VAL(13, \
+ (static_cast(unsigned long, n)) \
+ & 0x3)
+#define EBC_BXAP_OEN_ENCODE(n) PPC_REG_VAL(15, \
+ (static_cast(unsigned long, n)) \
+ & 0x3)
+#define EBC_BXAP_WBN_ENCODE(n) PPC_REG_VAL(17, \
+ (static_cast(unsigned long, n)) \
+ & 0x3)
+#define EBC_BXAP_WBF_ENCODE(n) PPC_REG_VAL(19, \
+ (static_cast(unsigned long, n)) \
+ & 0x3)
+#define EBC_BXAP_TH_ENCODE(n) PPC_REG_VAL(22, \
+ (static_cast(unsigned long, n)) \
+ & 0x7)
+#define EBC_BXAP_RE_ENABLED PPC_REG_VAL(23, 0x1)
+#define EBC_BXAP_RE_DISABLED PPC_REG_VAL(23, 0x0)
+#define EBC_BXAP_SOR_DELAYED PPC_REG_VAL(24, 0x0)
+#define EBC_BXAP_SOR_NONDELAYED PPC_REG_VAL(24, 0x1)
+#define EBC_BXAP_BEM_WRITEONLY PPC_REG_VAL(25, 0x0)
+#define EBC_BXAP_BEM_RW PPC_REG_VAL(25, 0x1)
+#define EBC_BXAP_PEN_DISABLED PPC_REG_VAL(26, 0x0)
+#define EBC_BXAP_PEN_ENABLED PPC_REG_VAL(26, 0x1)
+
+/* Configuration Register */
+#define EBC_CFG_LE_MASK PPC_REG_VAL(0, 0x1)
+#define EBC_CFG_LE_UNLOCK PPC_REG_VAL(0, 0x0)
+#define EBC_CFG_LE_LOCK PPC_REG_VAL(0, 0x1)
+#define EBC_CFG_PTD_MASK PPC_REG_VAL(1, 0x1)
+#define EBC_CFG_PTD_ENABLE PPC_REG_VAL(1, 0x0)
+#define EBC_CFG_PTD_DISABLE PPC_REG_VAL(1, 0x1)
+#define EBC_CFG_RTC_MASK PPC_REG_VAL(4, 0x7)
+#define EBC_CFG_RTC_16PERCLK PPC_REG_VAL(4, 0x0)
+#define EBC_CFG_RTC_32PERCLK PPC_REG_VAL(4, 0x1)
+#define EBC_CFG_RTC_64PERCLK PPC_REG_VAL(4, 0x2)
+#define EBC_CFG_RTC_128PERCLK PPC_REG_VAL(4, 0x3)
+#define EBC_CFG_RTC_256PERCLK PPC_REG_VAL(4, 0x4)
+#define EBC_CFG_RTC_512PERCLK PPC_REG_VAL(4, 0x5)
+#define EBC_CFG_RTC_1024PERCLK PPC_REG_VAL(4, 0x6)
+#define EBC_CFG_RTC_2048PERCLK PPC_REG_VAL(4, 0x7)
+#define EBC_CFG_ATC_MASK PPC_REG_VAL(5, 0x1)
+#define EBC_CFG_ATC_HI PPC_REG_VAL(5, 0x0)
+#define EBC_CFG_ATC_PREVIOUS PPC_REG_VAL(5, 0x1)
+#define EBC_CFG_DTC_MASK PPC_REG_VAL(6, 0x1)
+#define EBC_CFG_DTC_HI PPC_REG_VAL(6, 0x0)
+#define EBC_CFG_DTC_PREVIOUS PPC_REG_VAL(6, 0x1)
+#define EBC_CFG_CTC_MASK PPC_REG_VAL(7, 0x1)
+#define EBC_CFG_CTC_HI PPC_REG_VAL(7, 0x0)
+#define EBC_CFG_CTC_PREVIOUS PPC_REG_VAL(7, 0x1)
+#define EBC_CFG_OEO_MASK PPC_REG_VAL(8, 0x1)
+#define EBC_CFG_OEO_DISABLE PPC_REG_VAL(8, 0x0)
+#define EBC_CFG_OEO_ENABLE PPC_REG_VAL(8, 0x1)
+#define EBC_CFG_EMC_MASK PPC_REG_VAL(9, 0x1)
+#define EBC_CFG_EMC_NONDEFAULT PPC_REG_VAL(9, 0x0)
+#define EBC_CFG_EMC_DEFAULT PPC_REG_VAL(9, 0x1)
+#define EBC_CFG_PME_MASK PPC_REG_VAL(14, 0x1)
+#define EBC_CFG_PME_DISABLE PPC_REG_VAL(14, 0x0)
+#define EBC_CFG_PME_ENABLE PPC_REG_VAL(14, 0x1)
+#define EBC_CFG_PMT_MASK PPC_REG_VAL(19, 0x1F)
+#define EBC_CFG_PMT_ENCODE(n) PPC_REG_VAL(19, \
+ (static_cast(unsigned long, n)) \
+ & 0x1F)
+#define EBC_CFG_PR_MASK PPC_REG_VAL(21, 0x3)
+#define EBC_CFG_PR_16 PPC_REG_VAL(21, 0x0)
+#define EBC_CFG_PR_32 PPC_REG_VAL(21, 0x1)
+#define EBC_CFG_PR_64 PPC_REG_VAL(21, 0x2)
+#define EBC_CFG_PR_128 PPC_REG_VAL(21, 0x3)
#ifndef CONFIG_405EP
/******************************************************************************
#if defined(CONFIG_405EX)
#define SDR0_SRST 0x0200
-#define SDRAM_BESR0 0x00
-#define SDRAM_BEARL 0x02
-#define SDRAM_BEARU 0x03
-#define SDRAM_WMIRQ 0x06 /**/
-#define SDRAM_PLBOPT 0x08 /**/
-#define SDRAM_PUABA 0x09 /**/
-#define SDRAM_MCSTAT 0x1F /* memory controller status */
-#define SDRAM_MCOPT1 0x20 /* memory controller options 1 */
-#define SDRAM_MCOPT2 0x21 /* memory controller options 2 */
-#define SDRAM_MODT0 0x22 /* on die termination for bank 0 */
-#define SDRAM_MODT1 0x23 /* on die termination for bank 1 */
-#define SDRAM_MODT2 0x24 /* on die termination for bank 2 */
-#define SDRAM_MODT3 0x25 /* on die termination for bank 3 */
-#define SDRAM_CODT 0x26 /* on die termination for controller */
-#define SDRAM_VVPR 0x27 /* variable VRef programmming */
-#define SDRAM_OPARS 0x28 /* on chip driver control setup */
-#define SDRAM_OPART 0x29 /* on chip driver control trigger */
-#define SDRAM_RTR 0x30 /* refresh timer */
-#define SDRAM_PMIT 0x34 /* power management idle timer */
-#define SDRAM_MB0CF 0x40 /* memory bank 0 configuration */
-#define SDRAM_MB1CF 0x44 /* memory bank 1 configuration */
-#define SDRAM_MB2CF 0x48 /* memory bank 2 configuration */
-#define SDRAM_MB3CF 0x4C /* memory bank 3 configuration */
-#define SDRAM_INITPLR0 0x50 /* manual initialization control */
-#define SDRAM_INITPLR1 0x51 /* manual initialization control */
-#define SDRAM_INITPLR2 0x52 /* manual initialization control */
-#define SDRAM_INITPLR3 0x53 /* manual initialization control */
-#define SDRAM_INITPLR4 0x54 /* manual initialization control */
-#define SDRAM_INITPLR5 0x55 /* manual initialization control */
-#define SDRAM_INITPLR6 0x56 /* manual initialization control */
-#define SDRAM_INITPLR7 0x57 /* manual initialization control */
-#define SDRAM_INITPLR8 0x58 /* manual initialization control */
-#define SDRAM_INITPLR9 0x59 /* manual initialization control */
-#define SDRAM_INITPLR10 0x5a /* manual initialization control */
-#define SDRAM_INITPLR11 0x5b /* manual initialization control */
-#define SDRAM_INITPLR12 0x5c /* manual initialization control */
-#define SDRAM_INITPLR13 0x5d /* manual initialization control */
-#define SDRAM_INITPLR14 0x5e /* manual initialization control */
-#define SDRAM_INITPLR15 0x5f /* manual initialization control */
-#define SDRAM_RQDC 0x70 /* read DQS delay control */
-#define SDRAM_RFDC 0x74 /* read feedback delay control */
-#define SDRAM_RDCC 0x78 /* read data capture control */
-#define SDRAM_DLCR 0x7A /* delay line calibration */
-#define SDRAM_CLKTR 0x80 /* DDR clock timing */
-#define SDRAM_WRDTR 0x81 /* write data, DQS, DM clock, timing */
-#define SDRAM_SDTR1 0x85 /* DDR SDRAM timing 1 */
-#define SDRAM_SDTR2 0x86 /* DDR SDRAM timing 2 */
-#define SDRAM_SDTR3 0x87 /* DDR SDRAM timing 3 */
-#define SDRAM_MMODE 0x88 /* memory mode */
-#define SDRAM_MEMODE 0x89 /* memory extended mode */
-#define SDRAM_ECCCR 0x98 /* ECC error status */
-#define SDRAM_RID 0xF8 /* revision ID */
-
-/*-----------------------------------------------------------------------------+
-| Memory Bank 0-7 configuration
-+-----------------------------------------------------------------------------*/
-#define SDRAM_RXBAS_SDSZ_4 0x00000000 /* 4M */
-#define SDRAM_RXBAS_SDSZ_8 0x00001000 /* 8M */
-#define SDRAM_RXBAS_SDSZ_16 0x00002000 /* 16M */
-#define SDRAM_RXBAS_SDSZ_32 0x00003000 /* 32M */
-#define SDRAM_RXBAS_SDSZ_64 0x00004000 /* 64M */
-#define SDRAM_RXBAS_SDSZ_128 0x00005000 /* 128M */
-#define SDRAM_RXBAS_SDSZ_256 0x00006000 /* 256M */
-#define SDRAM_RXBAS_SDSZ_512 0x00007000 /* 512M */
-#define SDRAM_RXBAS_SDSZ_1024 0x00008000 /* 1024M */
-#define SDRAM_RXBAS_SDSZ_2048 0x00009000 /* 2048M */
-#define SDRAM_RXBAS_SDSZ_4096 0x0000a000 /* 4096M */
-#define SDRAM_RXBAS_SDSZ_8192 0x0000b000 /* 8192M */
-
-/*-----------------------------------------------------------------------------+
-| Memory Controller Status
-+-----------------------------------------------------------------------------*/
-#define SDRAM_MCSTAT_MIC_MASK 0x80000000 /* Memory init status mask */
-#define SDRAM_MCSTAT_MIC_NOTCOMP 0x00000000 /* Mem init not complete */
-#define SDRAM_MCSTAT_MIC_COMP 0x80000000 /* Mem init complete */
-#define SDRAM_MCSTAT_SRMS_MASK 0x80000000 /* Mem self refresh stat mask */
-#define SDRAM_MCSTAT_SRMS_NOT_SF 0x00000000 /* Mem not in self refresh */
-#define SDRAM_MCSTAT_SRMS_SF 0x80000000 /* Mem in self refresh */
-
-/*-----------------------------------------------------------------------------+
-| Memory Controller Options 1
-+-----------------------------------------------------------------------------*/
-#define SDRAM_MCOPT1_MCHK_MASK 0x30000000 /* Memory data err check mask */
-#define SDRAM_MCOPT1_MCHK_NON 0x00000000 /* No ECC generation */
-#define SDRAM_MCOPT1_MCHK_GEN 0x20000000 /* ECC generation */
-#define SDRAM_MCOPT1_MCHK_CHK 0x10000000 /* ECC generation and check */
-#define SDRAM_MCOPT1_MCHK_CHK_REP 0x30000000 /* ECC generation, chk, report*/
-#define SDRAM_MCOPT1_MCHK_CHK_DECODE(n) ((((unsigned long)(n))>>28)&0x3)
-#define SDRAM_MCOPT1_RDEN_MASK 0x08000000 /* Registered DIMM mask */
-#define SDRAM_MCOPT1_RDEN 0x08000000 /* Registered DIMM enable */
-#define SDRAM_MCOPT1_PMU_MASK 0x06000000 /* Page management unit mask */
-#define SDRAM_MCOPT1_PMU_CLOSE 0x00000000 /* PMU Close */
-#define SDRAM_MCOPT1_PMU_OPEN 0x04000000 /* PMU Open */
-#define SDRAM_MCOPT1_PMU_AUTOCLOSE 0x02000000 /* PMU AutoClose */
-#define SDRAM_MCOPT1_DMWD_MASK 0x01000000 /* DRAM width mask */
-#define SDRAM_MCOPT1_DMWD_32 0x00000000 /* 32 bits */
-#define SDRAM_MCOPT1_DMWD_64 0x01000000 /* 64 bits */
-#define SDRAM_MCOPT1_UIOS_MASK 0x00C00000 /* Unused IO State */
-#define SDRAM_MCOPT1_BCNT_MASK 0x00200000 /* Bank count */
-#define SDRAM_MCOPT1_4_BANKS 0x00000000 /* 4 Banks */
-#define SDRAM_MCOPT1_8_BANKS 0x00200000 /* 8 Banks */
-#define SDRAM_MCOPT1_DDR_TYPE_MASK 0x00100000 /* DDR Memory Type mask */
-#define SDRAM_MCOPT1_DDR1_TYPE 0x00000000 /* DDR1 Memory Type */
-#define SDRAM_MCOPT1_DDR2_TYPE 0x00100000 /* DDR2 Memory Type */
-#define SDRAM_MCOPT1_QDEP 0x00020000 /* 4 commands deep */
-#define SDRAM_MCOPT1_RWOO_MASK 0x00008000 /* Out of Order Read mask */
-#define SDRAM_MCOPT1_RWOO_DISABLED 0x00000000 /* disabled */
-#define SDRAM_MCOPT1_RWOO_ENABLED 0x00008000 /* enabled */
-#define SDRAM_MCOPT1_WOOO_MASK 0x00004000 /* Out of Order Write mask */
-#define SDRAM_MCOPT1_WOOO_DISABLED 0x00000000 /* disabled */
-#define SDRAM_MCOPT1_WOOO_ENABLED 0x00004000 /* enabled */
-#define SDRAM_MCOPT1_DCOO_MASK 0x00002000 /* All Out of Order mask */
-#define SDRAM_MCOPT1_DCOO_DISABLED 0x00002000 /* disabled */
-#define SDRAM_MCOPT1_DCOO_ENABLED 0x00000000 /* enabled */
-#define SDRAM_MCOPT1_DREF_MASK 0x00001000 /* Deferred refresh mask */
-#define SDRAM_MCOPT1_DREF_NORMAL 0x00000000 /* normal refresh */
-#define SDRAM_MCOPT1_DREF_DEFER_4 0x00001000 /* defer up to 4 refresh cmd */
-
-/*-----------------------------------------------------------------------------+
-| Memory Controller Options 2
-+-----------------------------------------------------------------------------*/
-#define SDRAM_MCOPT2_SREN_MASK 0x80000000 /* Self Test mask */
-#define SDRAM_MCOPT2_SREN_EXIT 0x00000000 /* Self Test exit */
-#define SDRAM_MCOPT2_SREN_ENTER 0x80000000 /* Self Test enter */
-#define SDRAM_MCOPT2_PMEN_MASK 0x40000000 /* Power Management mask */
-#define SDRAM_MCOPT2_PMEN_DISABLE 0x00000000 /* disable */
-#define SDRAM_MCOPT2_PMEN_ENABLE 0x40000000 /* enable */
-#define SDRAM_MCOPT2_IPTR_MASK 0x20000000 /* Init Trigger Reg mask */
-#define SDRAM_MCOPT2_IPTR_IDLE 0x00000000 /* idle */
-#define SDRAM_MCOPT2_IPTR_EXECUTE 0x20000000 /* execute preloaded init */
-#define SDRAM_MCOPT2_XSRP_MASK 0x10000000 /* Exit Self Refresh Prevent */
-#define SDRAM_MCOPT2_XSRP_ALLOW 0x00000000 /* allow self refresh exit */
-#define SDRAM_MCOPT2_XSRP_PREVENT 0x10000000 /* prevent self refresh exit */
-#define SDRAM_MCOPT2_DCEN_MASK 0x08000000 /* SDRAM Controller Enable */
-#define SDRAM_MCOPT2_DCEN_DISABLE 0x00000000 /* SDRAM Controller Enable */
-#define SDRAM_MCOPT2_DCEN_ENABLE 0x08000000 /* SDRAM Controller Enable */
-#define SDRAM_MCOPT2_ISIE_MASK 0x04000000 /* Init Seq Interruptable mas*/
-#define SDRAM_MCOPT2_ISIE_DISABLE 0x00000000 /* disable */
-#define SDRAM_MCOPT2_ISIE_ENABLE 0x04000000 /* enable */
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Refresh Timer Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_RTR_RINT_MASK 0xFFF80000
-#define SDRAM_RTR_RINT_ENCODE(n) ((((unsigned long)(n))&0xFFF8)<<16)
-#define SDRAM_RTR_RINT_DECODE(n) ((((unsigned long)(n))>>16)&0xFFF8)
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Read DQS Delay Control Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_RQDC_RQDE_MASK 0x80000000
-#define SDRAM_RQDC_RQDE_DISABLE 0x00000000
-#define SDRAM_RQDC_RQDE_ENABLE 0x80000000
-#define SDRAM_RQDC_RQFD_MASK 0x000001FF
-#define SDRAM_RQDC_RQFD_ENCODE(n) ((((unsigned long)(n))&0x1FF)<<0)
-
-#define SDRAM_RQDC_RQFD_MAX 0xFF
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Read Data Capture Control Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_RDCC_RDSS_MASK 0xC0000000
-#define SDRAM_RDCC_RDSS_T1 0x00000000
-#define SDRAM_RDCC_RDSS_T2 0x40000000
-#define SDRAM_RDCC_RDSS_T3 0x80000000
-#define SDRAM_RDCC_RDSS_T4 0xC0000000
-#define SDRAM_RDCC_RSAE_MASK 0x00000001
-#define SDRAM_RDCC_RSAE_DISABLE 0x00000001
-#define SDRAM_RDCC_RSAE_ENABLE 0x00000000
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Read Feedback Delay Control Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_RFDC_ARSE_MASK 0x80000000
-#define SDRAM_RFDC_ARSE_DISABLE 0x80000000
-#define SDRAM_RFDC_ARSE_ENABLE 0x00000000
-#define SDRAM_RFDC_RFOS_MASK 0x007F0000
-#define SDRAM_RFDC_RFOS_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16)
-#define SDRAM_RFDC_RFFD_MASK 0x000003FF
-#define SDRAM_RFDC_RFFD_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<0)
-
-#define SDRAM_RFDC_RFFD_MAX 0x4FF
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Delay Line Calibration Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_DLCR_DCLM_MASK 0x80000000
-#define SDRAM_DLCR_DCLM_MANUEL 0x80000000
-#define SDRAM_DLCR_DCLM_AUTO 0x00000000
-#define SDRAM_DLCR_DLCR_MASK 0x08000000
-#define SDRAM_DLCR_DLCR_CALIBRATE 0x08000000
-#define SDRAM_DLCR_DLCR_IDLE 0x00000000
-#define SDRAM_DLCR_DLCS_MASK 0x07000000
-#define SDRAM_DLCR_DLCS_NOT_RUN 0x00000000
-#define SDRAM_DLCR_DLCS_IN_PROGRESS 0x01000000
-#define SDRAM_DLCR_DLCS_COMPLETE 0x02000000
-#define SDRAM_DLCR_DLCS_CONT_DONE 0x03000000
-#define SDRAM_DLCR_DLCS_ERROR 0x04000000
-#define SDRAM_DLCR_DLCV_MASK 0x000001FF
-#define SDRAM_DLCR_DLCV_ENCODE(n) ((((unsigned long)(n))&0x1FF)<<0)
-#define SDRAM_DLCR_DLCV_DECODE(n) ((((unsigned long)(n))>>0)&0x1FF)
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Controller On Die Termination Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_CODT_ODT_ON 0x80000000
-#define SDRAM_CODT_ODT_OFF 0x00000000
-#define SDRAM_CODT_DQS_VOLTAGE_DDR_MASK 0x00000020
-#define SDRAM_CODT_DQS_2_5_V_DDR1 0x00000000
-#define SDRAM_CODT_DQS_1_8_V_DDR2 0x00000020
-#define SDRAM_CODT_DQS_MASK 0x00000010
-#define SDRAM_CODT_DQS_DIFFERENTIAL 0x00000000
-#define SDRAM_CODT_DQS_SINGLE_END 0x00000010
-#define SDRAM_CODT_CKSE_DIFFERENTIAL 0x00000000
-#define SDRAM_CODT_CKSE_SINGLE_END 0x00000008
-#define SDRAM_CODT_FEEBBACK_RCV_SINGLE_END 0x00000004
-#define SDRAM_CODT_FEEBBACK_DRV_SINGLE_END 0x00000002
-#define SDRAM_CODT_IO_HIZ 0x00000000
-#define SDRAM_CODT_IO_NMODE 0x00000001
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Mode Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_MMODE_WR_MASK 0x00000E00
-#define SDRAM_MMODE_WR_DDR1 0x00000000
-#define SDRAM_MMODE_WR_DDR2_3_CYC 0x00000400
-#define SDRAM_MMODE_WR_DDR2_4_CYC 0x00000600
-#define SDRAM_MMODE_WR_DDR2_5_CYC 0x00000800
-#define SDRAM_MMODE_WR_DDR2_6_CYC 0x00000A00
-#define SDRAM_MMODE_DCL_MASK 0x00000070
-#define SDRAM_MMODE_DCL_DDR1_2_0_CLK 0x00000020
-#define SDRAM_MMODE_DCL_DDR1_2_5_CLK 0x00000060
-#define SDRAM_MMODE_DCL_DDR1_3_0_CLK 0x00000030
-#define SDRAM_MMODE_DCL_DDR2_2_0_CLK 0x00000020
-#define SDRAM_MMODE_DCL_DDR2_3_0_CLK 0x00000030
-#define SDRAM_MMODE_DCL_DDR2_4_0_CLK 0x00000040
-#define SDRAM_MMODE_DCL_DDR2_5_0_CLK 0x00000050
-#define SDRAM_MMODE_DCL_DDR2_6_0_CLK 0x00000060
-#define SDRAM_MMODE_DCL_DDR2_7_0_CLK 0x00000070
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Extended Mode Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_MEMODE_DIC_MASK 0x00000002
-#define SDRAM_MEMODE_DIC_NORMAL 0x00000000
-#define SDRAM_MEMODE_DIC_WEAK 0x00000002
-#define SDRAM_MEMODE_DLL_MASK 0x00000001
-#define SDRAM_MEMODE_DLL_DISABLE 0x00000001
-#define SDRAM_MEMODE_DLL_ENABLE 0x00000000
-#define SDRAM_MEMODE_RTT_MASK 0x00000044
-#define SDRAM_MEMODE_RTT_DISABLED 0x00000000
-#define SDRAM_MEMODE_RTT_75OHM 0x00000004
-#define SDRAM_MEMODE_RTT_150OHM 0x00000040
-#define SDRAM_MEMODE_DQS_MASK 0x00000400
-#define SDRAM_MEMODE_DQS_DISABLE 0x00000400
-#define SDRAM_MEMODE_DQS_ENABLE 0x00000000
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Clock Timing Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_CLKTR_CLKP_MASK 0xC0000000
-#define SDRAM_CLKTR_CLKP_0_DEG 0x00000000
-#define SDRAM_CLKTR_CLKP_180_DEG_ADV 0x80000000
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Write Timing Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_WRDTR_WDTP_1_CYC 0x80000000
-#define SDRAM_WRDTR_LLWP_MASK 0x10000000
-#define SDRAM_WRDTR_LLWP_DIS 0x10000000
-#define SDRAM_WRDTR_LLWP_1_CYC 0x00000000
-#define SDRAM_WRDTR_WTR_MASK 0x0E000000
-#define SDRAM_WRDTR_WTR_0_DEG 0x06000000
-#define SDRAM_WRDTR_WTR_180_DEG_ADV 0x02000000
-#define SDRAM_WRDTR_WTR_270_DEG_ADV 0x00000000
-
-/*-----------------------------------------------------------------------------+
-| SDRAM SDTR1 Options
-+-----------------------------------------------------------------------------*/
-#define SDRAM_SDTR1_LDOF_MASK 0x80000000
-#define SDRAM_SDTR1_LDOF_1_CLK 0x00000000
-#define SDRAM_SDTR1_LDOF_2_CLK 0x80000000
-#define SDRAM_SDTR1_RTW_MASK 0x00F00000
-#define SDRAM_SDTR1_RTW_2_CLK 0x00200000
-#define SDRAM_SDTR1_RTW_3_CLK 0x00300000
-#define SDRAM_SDTR1_WTWO_MASK 0x000F0000
-#define SDRAM_SDTR1_WTWO_0_CLK 0x00000000
-#define SDRAM_SDTR1_WTWO_1_CLK 0x00010000
-#define SDRAM_SDTR1_RTRO_MASK 0x0000F000
-#define SDRAM_SDTR1_RTRO_1_CLK 0x00000000
-#define SDRAM_SDTR1_RTRO_2_CLK 0x00002000
-
-/*-----------------------------------------------------------------------------+
-| SDRAM SDTR2 Options
-+-----------------------------------------------------------------------------*/
-#define SDRAM_SDTR2_RCD_MASK 0xF0000000
-#define SDRAM_SDTR2_RCD_1_CLK 0x10000000
-#define SDRAM_SDTR2_RCD_2_CLK 0x20000000
-#define SDRAM_SDTR2_RCD_3_CLK 0x30000000
-#define SDRAM_SDTR2_RCD_4_CLK 0x40000000
-#define SDRAM_SDTR2_RCD_5_CLK 0x50000000
-#define SDRAM_SDTR2_WTR_MASK 0x0F000000
-#define SDRAM_SDTR2_WTR_1_CLK 0x01000000
-#define SDRAM_SDTR2_WTR_2_CLK 0x02000000
-#define SDRAM_SDTR2_WTR_3_CLK 0x03000000
-#define SDRAM_SDTR2_WTR_4_CLK 0x04000000
-#define SDRAM_SDTR3_WTR_ENCODE(n) ((((unsigned long)(n))&0xF)<<24)
-#define SDRAM_SDTR2_XSNR_MASK 0x00FF0000
-#define SDRAM_SDTR2_XSNR_8_CLK 0x00080000
-#define SDRAM_SDTR2_XSNR_16_CLK 0x00100000
-#define SDRAM_SDTR2_XSNR_32_CLK 0x00200000
-#define SDRAM_SDTR2_XSNR_64_CLK 0x00400000
-#define SDRAM_SDTR2_WPC_MASK 0x0000F000
-#define SDRAM_SDTR2_WPC_2_CLK 0x00002000
-#define SDRAM_SDTR2_WPC_3_CLK 0x00003000
-#define SDRAM_SDTR2_WPC_4_CLK 0x00004000
-#define SDRAM_SDTR2_WPC_5_CLK 0x00005000
-#define SDRAM_SDTR2_WPC_6_CLK 0x00006000
-#define SDRAM_SDTR3_WPC_ENCODE(n) ((((unsigned long)(n))&0xF)<<12)
-#define SDRAM_SDTR2_RPC_MASK 0x00000F00
-#define SDRAM_SDTR2_RPC_2_CLK 0x00000200
-#define SDRAM_SDTR2_RPC_3_CLK 0x00000300
-#define SDRAM_SDTR2_RPC_4_CLK 0x00000400
-#define SDRAM_SDTR2_RP_MASK 0x000000F0
-#define SDRAM_SDTR2_RP_3_CLK 0x00000030
-#define SDRAM_SDTR2_RP_4_CLK 0x00000040
-#define SDRAM_SDTR2_RP_5_CLK 0x00000050
-#define SDRAM_SDTR2_RP_6_CLK 0x00000060
-#define SDRAM_SDTR2_RP_7_CLK 0x00000070
-#define SDRAM_SDTR2_RRD_MASK 0x0000000F
-#define SDRAM_SDTR2_RRD_2_CLK 0x00000002
-#define SDRAM_SDTR2_RRD_3_CLK 0x00000003
-
-/*-----------------------------------------------------------------------------+
-| SDRAM SDTR3 Options
-+-----------------------------------------------------------------------------*/
-#define SDRAM_SDTR3_RAS_MASK 0x1F000000
-#define SDRAM_SDTR3_RAS_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24)
-#define SDRAM_SDTR3_RC_MASK 0x001F0000
-#define SDRAM_SDTR3_RC_ENCODE(n) ((((unsigned long)(n))&0x1F)<<16)
-#define SDRAM_SDTR3_XCS_MASK 0x00001F00
-#define SDRAM_SDTR3_XCS 0x00000D00
-#define SDRAM_SDTR3_RFC_MASK 0x0000003F
-#define SDRAM_SDTR3_RFC_ENCODE(n) ((((unsigned long)(n))&0x3F)<<0)
-
-/*-----------------------------------------------------------------------------+
-| Memory Bank 0-1 configuration
-+-----------------------------------------------------------------------------*/
-#define SDRAM_BXCF_M_AM_MASK 0x00000F00 /* Addressing mode */
-#define SDRAM_BXCF_M_AM_0 0x00000000 /* Mode 0 */
-#define SDRAM_BXCF_M_AM_1 0x00000100 /* Mode 1 */
-#define SDRAM_BXCF_M_AM_2 0x00000200 /* Mode 2 */
-#define SDRAM_BXCF_M_AM_3 0x00000300 /* Mode 3 */
-#define SDRAM_BXCF_M_AM_4 0x00000400 /* Mode 4 */
-#define SDRAM_BXCF_M_AM_5 0x00000500 /* Mode 5 */
-#define SDRAM_BXCF_M_AM_6 0x00000600 /* Mode 6 */
-#define SDRAM_BXCF_M_AM_7 0x00000700 /* Mode 7 */
-#define SDRAM_BXCF_M_AM_8 0x00000800 /* Mode 8 */
-#define SDRAM_BXCF_M_AM_9 0x00000900 /* Mode 9 */
-#define SDRAM_BXCF_M_BE_MASK 0x00000001 /* Memory Bank Enable */
-#define SDRAM_BXCF_M_BE_DISABLE 0x00000000 /* Memory Bank Enable */
-#define SDRAM_BXCF_M_BE_ENABLE 0x00000001 /* Memory Bank Enable */
-
#define sdr_uart0 0x0120 /* UART0 Config */
#define sdr_uart1 0x0121 /* UART1 Config */
#define sdr_mfr 0x4300 /* SDR0_MFR reg */
#define SDR0_PFC1_GPT_FREQ 0x0000000f
#endif
+/* General Purpose Timer (GPT) Register Offsets */
+#define GPT0_TBC 0x00000000
+#define GPT0_IM 0x00000018
+#define GPT0_ISS 0x0000001C
+#define GPT0_ISC 0x00000020
+#define GPT0_IE 0x00000024
+#define GPT0_COMP0 0x00000080
+#define GPT0_COMP1 0x00000084
+#define GPT0_COMP2 0x00000088
+#define GPT0_COMP3 0x0000008C
+#define GPT0_COMP4 0x00000090
+#define GPT0_COMP5 0x00000094
+#define GPT0_COMP6 0x00000098
+#define GPT0_MASK0 0x000000C0
+#define GPT0_MASK1 0x000000C4
+#define GPT0_MASK2 0x000000C8
+#define GPT0_MASK3 0x000000CC
+#define GPT0_MASK4 0x000000D0
+#define GPT0_MASK5 0x000000D4
+#define GPT0_MASK6 0x000000D8
+#define GPT0_DCT0 0x00000110
+#define GPT0_DCIS 0x0000011C
+
#endif /* __PPC405_H__ */
#define sdr_plbtr 0x4200
#define sdr_mfr 0x4300 /* SDR0_MFR reg */
-/*-----------------------------------------------------------------------------
- | SDRAM Controller
- +----------------------------------------------------------------------------*/
-/* values for memcfga register - indirect addressing of these regs */
-#define mem_besr0_clr 0x0000 /* bus error status reg 0 (clr) */
-#define mem_besr0_set 0x0004 /* bus error status reg 0 (set) */
-#define mem_besr1_clr 0x0008 /* bus error status reg 1 (clr) */
-#define mem_besr1_set 0x000c /* bus error status reg 1 (set) */
-#define mem_bear 0x0010 /* bus error address reg */
-#define mem_mirq_clr 0x0011 /* bus master interrupt (clr) */
-#define mem_mirq_set 0x0012 /* bus master interrupt (set) */
-#define mem_slio 0x0018 /* ddr sdram slave interface options */
-#define mem_cfg0 0x0020 /* ddr sdram options 0 */
-#define mem_cfg1 0x0021 /* ddr sdram options 1 */
-#define mem_devopt 0x0022 /* ddr sdram device options */
-#define mem_mcsts 0x0024 /* memory controller status */
-#define mem_rtr 0x0030 /* refresh timer register */
-#define mem_pmit 0x0034 /* power management idle timer */
-#define mem_uabba 0x0038 /* plb UABus base address */
-#define mem_b0cr 0x0040 /* ddr sdram bank 0 configuration */
-#define mem_b1cr 0x0044 /* ddr sdram bank 1 configuration */
-#define mem_b2cr 0x0048 /* ddr sdram bank 2 configuration */
-#define mem_b3cr 0x004c /* ddr sdram bank 3 configuration */
-#define mem_tr0 0x0080 /* sdram timing register 0 */
-#define mem_tr1 0x0081 /* sdram timing register 1 */
-#define mem_clktr 0x0082 /* ddr clock timing register */
-#define mem_wddctr 0x0083 /* write data/dm/dqs clock timing reg */
-#define mem_dlycal 0x0084 /* delay line calibration register */
-#define mem_eccesr 0x0098 /* ECC error status */
-
#ifdef CONFIG_440GX
#define sdr_amp 0x0240
#define sdr_xpllc 0x01c1
#define SDR0_PEGPLLSTS 0x000003A2 /* PE Pll LC Tank Status */
#endif /* CONFIG_440SPE */
-#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
- defined(CONFIG_460EX) || defined(CONFIG_460GT)
-/*----------------------------------------------------------------------------+
-| SDRAM Controller
-+----------------------------------------------------------------------------*/
-/*-----------------------------------------------------------------------------+
-| SDRAM DLYCAL Options
-+-----------------------------------------------------------------------------*/
-#define SDRAM_DLYCAL_DLCV_MASK 0x000003FC
-#define SDRAM_DLYCAL_DLCV_ENCODE(x) (((x)<<2) & SDRAM_DLYCAL_DLCV_MASK)
-#define SDRAM_DLYCAL_DLCV_DECODE(x) (((x) & SDRAM_DLYCAL_DLCV_MASK)>>2)
-
-/*----------------------------------------------------------------------------+
-| Memory queue defines
-+----------------------------------------------------------------------------*/
-/* A REVOIR versus RWC - SG*/
-#define SDRAMQ_DCR_BASE 0x040
-
-#define SDRAM_R0BAS (SDRAMQ_DCR_BASE+0x0) /* rank 0 base address & size */
-#define SDRAM_R1BAS (SDRAMQ_DCR_BASE+0x1) /* rank 1 base address & size */
-#define SDRAM_R2BAS (SDRAMQ_DCR_BASE+0x2) /* rank 2 base address & size */
-#define SDRAM_R3BAS (SDRAMQ_DCR_BASE+0x3) /* rank 3 base address & size */
-#define SDRAM_CONF1HB (SDRAMQ_DCR_BASE+0x5) /* configuration 1 HB */
-#define SDRAM_ERRSTATHB (SDRAMQ_DCR_BASE+0x7) /* error status HB */
-#define SDRAM_ERRADDUHB (SDRAMQ_DCR_BASE+0x8) /* error address upper 32 HB */
-#define SDRAM_ERRADDLHB (SDRAMQ_DCR_BASE+0x9) /* error address lower 32 HB */
-#define SDRAM_PLBADDULL (SDRAMQ_DCR_BASE+0xA) /* PLB base address upper 32 LL */
-#define SDRAM_CONF1LL (SDRAMQ_DCR_BASE+0xB) /* configuration 1 LL */
-#define SDRAM_ERRSTATLL (SDRAMQ_DCR_BASE+0xC) /* error status LL */
-#define SDRAM_ERRADDULL (SDRAMQ_DCR_BASE+0xD) /* error address upper 32 LL */
-#define SDRAM_ERRADDLLL (SDRAMQ_DCR_BASE+0xE) /* error address lower 32 LL */
-#define SDRAM_CONFPATHB (SDRAMQ_DCR_BASE+0xF) /* configuration between paths */
-#define SDRAM_PLBADDUHB (SDRAMQ_DCR_BASE+0x10) /* PLB base address upper 32 LL */
-
-/*-----------------------------------------------------------------------------+
-| Memory Bank 0-7 configuration
-+-----------------------------------------------------------------------------*/
-#if defined(CONFIG_440SPE) || \
- defined(CONFIG_460EX) || defined(CONFIG_460GT)
-#define SDRAM_RXBAS_SDBA_MASK 0xFFE00000 /* Base address */
-#define SDRAM_RXBAS_SDBA_ENCODE(n) ((((unsigned long)(n))&0xFFE00000)>>2)
-#define SDRAM_RXBAS_SDBA_DECODE(n) ((((unsigned long)(n))&0xFFE00000)<<2)
-#endif /* CONFIG_440SPE */
-#if defined(CONFIG_440SP)
-#define SDRAM_RXBAS_SDBA_MASK 0xFF800000 /* Base address */
-#define SDRAM_RXBAS_SDBA_ENCODE(n) ((((unsigned long)(n))&0xFF800000))
-#define SDRAM_RXBAS_SDBA_DECODE(n) ((((unsigned long)(n))&0xFF800000))
-#endif /* CONFIG_440SP */
-#define SDRAM_RXBAS_SDSZ_MASK 0x0000FFC0 /* Size */
-#define SDRAM_RXBAS_SDSZ_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<6)
-#define SDRAM_RXBAS_SDSZ_DECODE(n) ((((unsigned long)(n))>>6)&0x3FF)
-#define SDRAM_RXBAS_SDSZ_0 0x00000000 /* 0M */
-#define SDRAM_RXBAS_SDSZ_8 0x0000FFC0 /* 8M */
-#define SDRAM_RXBAS_SDSZ_16 0x0000FF80 /* 16M */
-#define SDRAM_RXBAS_SDSZ_32 0x0000FF00 /* 32M */
-#define SDRAM_RXBAS_SDSZ_64 0x0000FE00 /* 64M */
-#define SDRAM_RXBAS_SDSZ_128 0x0000FC00 /* 128M */
-#define SDRAM_RXBAS_SDSZ_256 0x0000F800 /* 256M */
-#define SDRAM_RXBAS_SDSZ_512 0x0000F000 /* 512M */
-#define SDRAM_RXBAS_SDSZ_1024 0x0000E000 /* 1024M */
-#define SDRAM_RXBAS_SDSZ_2048 0x0000C000 /* 2048M */
-#define SDRAM_RXBAS_SDSZ_4096 0x00008000 /* 4096M */
-
-/*----------------------------------------------------------------------------+
-| Memory controller defines
-+----------------------------------------------------------------------------*/
-/* A REVOIR versus specs 4 bank - SG*/
-#define SDRAM_MCSTAT 0x14 /* memory controller status */
-#define SDRAM_MCOPT1 0x20 /* memory controller options 1 */
-#define SDRAM_MCOPT2 0x21 /* memory controller options 2 */
-#define SDRAM_MODT0 0x22 /* on die termination for bank 0 */
-#define SDRAM_MODT1 0x23 /* on die termination for bank 1 */
-#define SDRAM_MODT2 0x24 /* on die termination for bank 2 */
-#define SDRAM_MODT3 0x25 /* on die termination for bank 3 */
-#define SDRAM_CODT 0x26 /* on die termination for controller */
-#define SDRAM_VVPR 0x27 /* variable VRef programmming */
-#define SDRAM_OPARS 0x28 /* on chip driver control setup */
-#define SDRAM_OPART 0x29 /* on chip driver control trigger */
-#define SDRAM_RTR 0x30 /* refresh timer */
-#define SDRAM_PMIT 0x34 /* power management idle timer */
-#define SDRAM_MB0CF 0x40 /* memory bank 0 configuration */
-#define SDRAM_MB1CF 0x44 /* memory bank 1 configuration */
-#define SDRAM_MB2CF 0x48
-#define SDRAM_MB3CF 0x4C
-#define SDRAM_INITPLR0 0x50 /* manual initialization control */
-#define SDRAM_INITPLR1 0x51 /* manual initialization control */
-#define SDRAM_INITPLR2 0x52 /* manual initialization control */
-#define SDRAM_INITPLR3 0x53 /* manual initialization control */
-#define SDRAM_INITPLR4 0x54 /* manual initialization control */
-#define SDRAM_INITPLR5 0x55 /* manual initialization control */
-#define SDRAM_INITPLR6 0x56 /* manual initialization control */
-#define SDRAM_INITPLR7 0x57 /* manual initialization control */
-#define SDRAM_INITPLR8 0x58 /* manual initialization control */
-#define SDRAM_INITPLR9 0x59 /* manual initialization control */
-#define SDRAM_INITPLR10 0x5a /* manual initialization control */
-#define SDRAM_INITPLR11 0x5b /* manual initialization control */
-#define SDRAM_INITPLR12 0x5c /* manual initialization control */
-#define SDRAM_INITPLR13 0x5d /* manual initialization control */
-#define SDRAM_INITPLR14 0x5e /* manual initialization control */
-#define SDRAM_INITPLR15 0x5f /* manual initialization control */
-#define SDRAM_RQDC 0x70 /* read DQS delay control */
-#define SDRAM_RFDC 0x74 /* read feedback delay control */
-#define SDRAM_RDCC 0x78 /* read data capture control */
-#define SDRAM_DLCR 0x7A /* delay line calibration */
-#define SDRAM_CLKTR 0x80 /* DDR clock timing */
-#define SDRAM_WRDTR 0x81 /* write data, DQS, DM clock, timing */
-#define SDRAM_SDTR1 0x85 /* DDR SDRAM timing 1 */
-#define SDRAM_SDTR2 0x86 /* DDR SDRAM timing 2 */
-#define SDRAM_SDTR3 0x87 /* DDR SDRAM timing 3 */
-#define SDRAM_MMODE 0x88 /* memory mode */
-#define SDRAM_MEMODE 0x89 /* memory extended mode */
-#define SDRAM_ECCCR 0x98 /* ECC error status */
-#define SDRAM_CID 0xA4 /* core ID */
-#define SDRAM_RID 0xA8 /* revision ID */
-#define SDRAM_RTSR 0xB1 /* run time status tracking */
-
-/*-----------------------------------------------------------------------------+
-| Memory Controller Status
-+-----------------------------------------------------------------------------*/
-#define SDRAM_MCSTAT_MIC_MASK 0x80000000 /* Memory init status mask */
-#define SDRAM_MCSTAT_MIC_NOTCOMP 0x00000000 /* Mem init not complete */
-#define SDRAM_MCSTAT_MIC_COMP 0x80000000 /* Mem init complete */
-#define SDRAM_MCSTAT_SRMS_MASK 0x40000000 /* Mem self refresh stat mask */
-#define SDRAM_MCSTAT_SRMS_NOT_SF 0x00000000 /* Mem not in self refresh */
-#define SDRAM_MCSTAT_SRMS_SF 0x40000000 /* Mem in self refresh */
-#define SDRAM_MCSTAT_IDLE_MASK 0x20000000 /* Mem self refresh stat mask */
-#define SDRAM_MCSTAT_IDLE_NOT 0x00000000 /* Mem contr not idle */
-#define SDRAM_MCSTAT_IDLE 0x20000000 /* Mem contr idle */
-
-/*-----------------------------------------------------------------------------+
-| Memory Controller Options 1
-+-----------------------------------------------------------------------------*/
-#define SDRAM_MCOPT1_MCHK_MASK 0x30000000 /* Memory data err check mask*/
-#define SDRAM_MCOPT1_MCHK_NON 0x00000000 /* No ECC generation */
-#define SDRAM_MCOPT1_MCHK_GEN 0x20000000 /* ECC generation */
-#define SDRAM_MCOPT1_MCHK_CHK 0x10000000 /* ECC generation and check */
-#define SDRAM_MCOPT1_MCHK_CHK_REP 0x30000000 /* ECC generation, chk, report*/
-#define SDRAM_MCOPT1_MCHK_CHK_DECODE(n) ((((unsigned long)(n))>>28)&0x3)
-#define SDRAM_MCOPT1_RDEN_MASK 0x08000000 /* Registered DIMM mask */
-#define SDRAM_MCOPT1_RDEN 0x08000000 /* Registered DIMM enable */
-#define SDRAM_MCOPT1_PMU_MASK 0x06000000 /* Page management unit mask */
-#define SDRAM_MCOPT1_PMU_CLOSE 0x00000000 /* PMU Close */
-#define SDRAM_MCOPT1_PMU_OPEN 0x04000000 /* PMU Open */
-#define SDRAM_MCOPT1_PMU_AUTOCLOSE 0x02000000 /* PMU AutoClose */
-#define SDRAM_MCOPT1_DMWD_MASK 0x01000000 /* DRAM width mask */
-#define SDRAM_MCOPT1_DMWD_32 0x00000000 /* 32 bits */
-#define SDRAM_MCOPT1_DMWD_64 0x01000000 /* 64 bits */
-#define SDRAM_MCOPT1_UIOS_MASK 0x00C00000 /* Unused IO State */
-#define SDRAM_MCOPT1_BCNT_MASK 0x00200000 /* Bank count */
-#define SDRAM_MCOPT1_4_BANKS 0x00000000 /* 4 Banks */
-#define SDRAM_MCOPT1_8_BANKS 0x00200000 /* 8 Banks */
-#define SDRAM_MCOPT1_DDR_TYPE_MASK 0x00100000 /* DDR Memory Type mask */
-#define SDRAM_MCOPT1_DDR1_TYPE 0x00000000 /* DDR1 Memory Type */
-#define SDRAM_MCOPT1_DDR2_TYPE 0x00100000 /* DDR2 Memory Type */
-#define SDRAM_MCOPT1_QDEP 0x00020000 /* 4 commands deep */
-#define SDRAM_MCOPT1_RWOO_MASK 0x00008000 /* Out of Order Read mask */
-#define SDRAM_MCOPT1_RWOO_DISABLED 0x00000000 /* disabled */
-#define SDRAM_MCOPT1_RWOO_ENABLED 0x00008000 /* enabled */
-#define SDRAM_MCOPT1_WOOO_MASK 0x00004000 /* Out of Order Write mask */
-#define SDRAM_MCOPT1_WOOO_DISABLED 0x00000000 /* disabled */
-#define SDRAM_MCOPT1_WOOO_ENABLED 0x00004000 /* enabled */
-#define SDRAM_MCOPT1_DCOO_MASK 0x00002000 /* All Out of Order mask */
-#define SDRAM_MCOPT1_DCOO_DISABLED 0x00002000 /* disabled */
-#define SDRAM_MCOPT1_DCOO_ENABLED 0x00000000 /* enabled */
-#define SDRAM_MCOPT1_DREF_MASK 0x00001000 /* Deferred refresh mask */
-#define SDRAM_MCOPT1_DREF_NORMAL 0x00000000 /* normal refresh */
-#define SDRAM_MCOPT1_DREF_DEFER_4 0x00001000 /* defer up to 4 refresh cmd */
-
-/*-----------------------------------------------------------------------------+
-| Memory Controller Options 2
-+-----------------------------------------------------------------------------*/
-#define SDRAM_MCOPT2_SREN_MASK 0x80000000 /* Self Test mask */
-#define SDRAM_MCOPT2_SREN_EXIT 0x00000000 /* Self Test exit */
-#define SDRAM_MCOPT2_SREN_ENTER 0x80000000 /* Self Test enter */
-#define SDRAM_MCOPT2_PMEN_MASK 0x40000000 /* Power Management mask */
-#define SDRAM_MCOPT2_PMEN_DISABLE 0x00000000 /* disable */
-#define SDRAM_MCOPT2_PMEN_ENABLE 0x40000000 /* enable */
-#define SDRAM_MCOPT2_IPTR_MASK 0x20000000 /* Init Trigger Reg mask */
-#define SDRAM_MCOPT2_IPTR_IDLE 0x00000000 /* idle */
-#define SDRAM_MCOPT2_IPTR_EXECUTE 0x20000000 /* execute preloaded init */
-#define SDRAM_MCOPT2_XSRP_MASK 0x10000000 /* Exit Self Refresh Prevent */
-#define SDRAM_MCOPT2_XSRP_ALLOW 0x00000000 /* allow self refresh exit */
-#define SDRAM_MCOPT2_XSRP_PREVENT 0x10000000 /* prevent self refresh exit */
-#define SDRAM_MCOPT2_DCEN_MASK 0x08000000 /* SDRAM Controller Enable */
-#define SDRAM_MCOPT2_DCEN_DISABLE 0x00000000 /* SDRAM Controller Enable */
-#define SDRAM_MCOPT2_DCEN_ENABLE 0x08000000 /* SDRAM Controller Enable */
-#define SDRAM_MCOPT2_ISIE_MASK 0x04000000 /* Init Seq Interruptable mas*/
-#define SDRAM_MCOPT2_ISIE_DISABLE 0x00000000 /* disable */
-#define SDRAM_MCOPT2_ISIE_ENABLE 0x04000000 /* enable */
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Refresh Timer Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_RTR_RINT_MASK 0xFFF80000
-#define SDRAM_RTR_RINT_ENCODE(n) ((((unsigned long)(n))&0xFFF8)<<16)
-#define SDRAM_RTR_RINT_DECODE(n) ((((unsigned long)(n))>>16)&0xFFF8)
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Read DQS Delay Control Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_RQDC_RQDE_MASK 0x80000000
-#define SDRAM_RQDC_RQDE_DISABLE 0x00000000
-#define SDRAM_RQDC_RQDE_ENABLE 0x80000000
-#define SDRAM_RQDC_RQFD_MASK 0x000001FF
-#define SDRAM_RQDC_RQFD_ENCODE(n) ((((unsigned long)(n))&0x1FF)<<0)
-
-#define SDRAM_RQDC_RQFD_MAX 0x1FF
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Read Data Capture Control Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_RDCC_RDSS_MASK 0xC0000000
-#define SDRAM_RDCC_RDSS_T1 0x00000000
-#define SDRAM_RDCC_RDSS_T2 0x40000000
-#define SDRAM_RDCC_RDSS_T3 0x80000000
-#define SDRAM_RDCC_RDSS_T4 0xC0000000
-#define SDRAM_RDCC_RSAE_MASK 0x00000001
-#define SDRAM_RDCC_RSAE_DISABLE 0x00000001
-#define SDRAM_RDCC_RSAE_ENABLE 0x00000000
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Read Feedback Delay Control Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_RFDC_ARSE_MASK 0x80000000
-#define SDRAM_RFDC_ARSE_DISABLE 0x80000000
-#define SDRAM_RFDC_ARSE_ENABLE 0x00000000
-#define SDRAM_RFDC_RFOS_MASK 0x007F0000
-#define SDRAM_RFDC_RFOS_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16)
-#define SDRAM_RFDC_RFFD_MASK 0x000007FF
-#define SDRAM_RFDC_RFFD_ENCODE(n) ((((unsigned long)(n))&0x7FF)<<0)
-
-#define SDRAM_RFDC_RFFD_MAX 0x7FF
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Delay Line Calibration Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_DLCR_DCLM_MASK 0x80000000
-#define SDRAM_DLCR_DCLM_MANUEL 0x80000000
-#define SDRAM_DLCR_DCLM_AUTO 0x00000000
-#define SDRAM_DLCR_DLCR_MASK 0x08000000
-#define SDRAM_DLCR_DLCR_CALIBRATE 0x08000000
-#define SDRAM_DLCR_DLCR_IDLE 0x00000000
-#define SDRAM_DLCR_DLCS_MASK 0x07000000
-#define SDRAM_DLCR_DLCS_NOT_RUN 0x00000000
-#define SDRAM_DLCR_DLCS_IN_PROGRESS 0x01000000
-#define SDRAM_DLCR_DLCS_COMPLETE 0x02000000
-#define SDRAM_DLCR_DLCS_CONT_DONE 0x03000000
-#define SDRAM_DLCR_DLCS_ERROR 0x04000000
-#define SDRAM_DLCR_DLCV_MASK 0x000001FF
-#define SDRAM_DLCR_DLCV_ENCODE(n) ((((unsigned long)(n))&0x1FF)<<0)
-#define SDRAM_DLCR_DLCV_DECODE(n) ((((unsigned long)(n))>>0)&0x1FF)
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Controller On Die Termination Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_CODT_ODT_ON 0x80000000
-#define SDRAM_CODT_ODT_OFF 0x00000000
-#define SDRAM_CODT_DQS_VOLTAGE_DDR_MASK 0x00000020
-#define SDRAM_CODT_DQS_2_5_V_DDR1 0x00000000
-#define SDRAM_CODT_DQS_1_8_V_DDR2 0x00000020
-#define SDRAM_CODT_DQS_MASK 0x00000010
-#define SDRAM_CODT_DQS_DIFFERENTIAL 0x00000000
-#define SDRAM_CODT_DQS_SINGLE_END 0x00000010
-#define SDRAM_CODT_CKSE_DIFFERENTIAL 0x00000000
-#define SDRAM_CODT_CKSE_SINGLE_END 0x00000008
-#define SDRAM_CODT_FEEBBACK_RCV_SINGLE_END 0x00000004
-#define SDRAM_CODT_FEEBBACK_DRV_SINGLE_END 0x00000002
-#define SDRAM_CODT_IO_HIZ 0x00000000
-#define SDRAM_CODT_IO_NMODE 0x00000001
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Mode Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_MMODE_WR_MASK 0x00000E00
-#define SDRAM_MMODE_WR_DDR1 0x00000000
-#define SDRAM_MMODE_WR_DDR2_3_CYC 0x00000400
-#define SDRAM_MMODE_WR_DDR2_4_CYC 0x00000600
-#define SDRAM_MMODE_WR_DDR2_5_CYC 0x00000800
-#define SDRAM_MMODE_WR_DDR2_6_CYC 0x00000A00
-#define SDRAM_MMODE_DCL_MASK 0x00000070
-#define SDRAM_MMODE_DCL_DDR1_2_0_CLK 0x00000020
-#define SDRAM_MMODE_DCL_DDR1_2_5_CLK 0x00000060
-#define SDRAM_MMODE_DCL_DDR1_3_0_CLK 0x00000030
-#define SDRAM_MMODE_DCL_DDR2_2_0_CLK 0x00000020
-#define SDRAM_MMODE_DCL_DDR2_3_0_CLK 0x00000030
-#define SDRAM_MMODE_DCL_DDR2_4_0_CLK 0x00000040
-#define SDRAM_MMODE_DCL_DDR2_5_0_CLK 0x00000050
-#define SDRAM_MMODE_DCL_DDR2_6_0_CLK 0x00000060
-#define SDRAM_MMODE_DCL_DDR2_7_0_CLK 0x00000070
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Extended Mode Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_MEMODE_DIC_MASK 0x00000002
-#define SDRAM_MEMODE_DIC_NORMAL 0x00000000
-#define SDRAM_MEMODE_DIC_WEAK 0x00000002
-#define SDRAM_MEMODE_DLL_MASK 0x00000001
-#define SDRAM_MEMODE_DLL_DISABLE 0x00000001
-#define SDRAM_MEMODE_DLL_ENABLE 0x00000000
-#define SDRAM_MEMODE_RTT_MASK 0x00000044
-#define SDRAM_MEMODE_RTT_DISABLED 0x00000000
-#define SDRAM_MEMODE_RTT_75OHM 0x00000004
-#define SDRAM_MEMODE_RTT_150OHM 0x00000040
-#define SDRAM_MEMODE_DQS_MASK 0x00000400
-#define SDRAM_MEMODE_DQS_DISABLE 0x00000400
-#define SDRAM_MEMODE_DQS_ENABLE 0x00000000
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Clock Timing Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_CLKTR_CLKP_MASK 0xC0000000
-#define SDRAM_CLKTR_CLKP_0_DEG 0x00000000
-#define SDRAM_CLKTR_CLKP_180_DEG_ADV 0x80000000
-#define SDRAM_CLKTR_CLKP_90_DEG_ADV 0x40000000
-#define SDRAM_CLKTR_CLKP_270_DEG_ADV 0xC0000000
-
-/*-----------------------------------------------------------------------------+
-| SDRAM Write Timing Register
-+-----------------------------------------------------------------------------*/
-#define SDRAM_WRDTR_LLWP_MASK 0x10000000
-#define SDRAM_WRDTR_LLWP_DIS 0x10000000
-#define SDRAM_WRDTR_LLWP_1_CYC 0x00000000
-#define SDRAM_WRDTR_WTR_MASK 0x0E000000
-#define SDRAM_WRDTR_WTR_0_DEG 0x06000000
-#define SDRAM_WRDTR_WTR_90_DEG_ADV 0x04000000
-#define SDRAM_WRDTR_WTR_180_DEG_ADV 0x02000000
-#define SDRAM_WRDTR_WTR_270_DEG_ADV 0x00000000
-
-/*-----------------------------------------------------------------------------+
-| SDRAM SDTR1 Options
-+-----------------------------------------------------------------------------*/
-#define SDRAM_SDTR1_LDOF_MASK 0x80000000
-#define SDRAM_SDTR1_LDOF_1_CLK 0x00000000
-#define SDRAM_SDTR1_LDOF_2_CLK 0x80000000
-#define SDRAM_SDTR1_RTW_MASK 0x00F00000
-#define SDRAM_SDTR1_RTW_2_CLK 0x00200000
-#define SDRAM_SDTR1_RTW_3_CLK 0x00300000
-#define SDRAM_SDTR1_WTWO_MASK 0x000F0000
-#define SDRAM_SDTR1_WTWO_0_CLK 0x00000000
-#define SDRAM_SDTR1_WTWO_1_CLK 0x00010000
-#define SDRAM_SDTR1_RTRO_MASK 0x0000F000
-#define SDRAM_SDTR1_RTRO_1_CLK 0x00001000
-#define SDRAM_SDTR1_RTRO_2_CLK 0x00002000
-
-/*-----------------------------------------------------------------------------+
-| SDRAM SDTR2 Options
-+-----------------------------------------------------------------------------*/
-#define SDRAM_SDTR2_RCD_MASK 0xF0000000
-#define SDRAM_SDTR2_RCD_1_CLK 0x10000000
-#define SDRAM_SDTR2_RCD_2_CLK 0x20000000
-#define SDRAM_SDTR2_RCD_3_CLK 0x30000000
-#define SDRAM_SDTR2_RCD_4_CLK 0x40000000
-#define SDRAM_SDTR2_RCD_5_CLK 0x50000000
-#define SDRAM_SDTR2_WTR_MASK 0x0F000000
-#define SDRAM_SDTR2_WTR_1_CLK 0x01000000
-#define SDRAM_SDTR2_WTR_2_CLK 0x02000000
-#define SDRAM_SDTR2_WTR_3_CLK 0x03000000
-#define SDRAM_SDTR2_WTR_4_CLK 0x04000000
-#define SDRAM_SDTR3_WTR_ENCODE(n) ((((unsigned long)(n))&0xF)<<24)
-#define SDRAM_SDTR2_XSNR_MASK 0x00FF0000
-#define SDRAM_SDTR2_XSNR_8_CLK 0x00080000
-#define SDRAM_SDTR2_XSNR_16_CLK 0x00100000
-#define SDRAM_SDTR2_XSNR_32_CLK 0x00200000
-#define SDRAM_SDTR2_XSNR_64_CLK 0x00400000
-#define SDRAM_SDTR2_WPC_MASK 0x0000F000
-#define SDRAM_SDTR2_WPC_2_CLK 0x00002000
-#define SDRAM_SDTR2_WPC_3_CLK 0x00003000
-#define SDRAM_SDTR2_WPC_4_CLK 0x00004000
-#define SDRAM_SDTR2_WPC_5_CLK 0x00005000
-#define SDRAM_SDTR2_WPC_6_CLK 0x00006000
-#define SDRAM_SDTR3_WPC_ENCODE(n) ((((unsigned long)(n))&0xF)<<12)
-#define SDRAM_SDTR2_RPC_MASK 0x00000F00
-#define SDRAM_SDTR2_RPC_2_CLK 0x00000200
-#define SDRAM_SDTR2_RPC_3_CLK 0x00000300
-#define SDRAM_SDTR2_RPC_4_CLK 0x00000400
-#define SDRAM_SDTR2_RP_MASK 0x000000F0
-#define SDRAM_SDTR2_RP_3_CLK 0x00000030
-#define SDRAM_SDTR2_RP_4_CLK 0x00000040
-#define SDRAM_SDTR2_RP_5_CLK 0x00000050
-#define SDRAM_SDTR2_RP_6_CLK 0x00000060
-#define SDRAM_SDTR2_RP_7_CLK 0x00000070
-#define SDRAM_SDTR2_RRD_MASK 0x0000000F
-#define SDRAM_SDTR2_RRD_2_CLK 0x00000002
-#define SDRAM_SDTR2_RRD_3_CLK 0x00000003
-
-/*-----------------------------------------------------------------------------+
-| SDRAM SDTR3 Options
-+-----------------------------------------------------------------------------*/
-#define SDRAM_SDTR3_RAS_MASK 0x1F000000
-#define SDRAM_SDTR3_RAS_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24)
-#define SDRAM_SDTR3_RC_MASK 0x001F0000
-#define SDRAM_SDTR3_RC_ENCODE(n) ((((unsigned long)(n))&0x1F)<<16)
-#define SDRAM_SDTR3_XCS_MASK 0x00001F00
-#define SDRAM_SDTR3_XCS 0x00000D00
-#define SDRAM_SDTR3_RFC_MASK 0x0000003F
-#define SDRAM_SDTR3_RFC_ENCODE(n) ((((unsigned long)(n))&0x3F)<<0)
-
-/*-----------------------------------------------------------------------------+
-| Memory Bank 0-1 configuration
-+-----------------------------------------------------------------------------*/
-#define SDRAM_BXCF_M_AM_MASK 0x00000F00 /* Addressing mode */
-#define SDRAM_BXCF_M_AM_0 0x00000000 /* Mode 0 */
-#define SDRAM_BXCF_M_AM_1 0x00000100 /* Mode 1 */
-#define SDRAM_BXCF_M_AM_2 0x00000200 /* Mode 2 */
-#define SDRAM_BXCF_M_AM_3 0x00000300 /* Mode 3 */
-#define SDRAM_BXCF_M_AM_4 0x00000400 /* Mode 4 */
-#define SDRAM_BXCF_M_AM_5 0x00000500 /* Mode 5 */
-#define SDRAM_BXCF_M_AM_6 0x00000600 /* Mode 6 */
-#define SDRAM_BXCF_M_AM_7 0x00000700 /* Mode 7 */
-#define SDRAM_BXCF_M_AM_8 0x00000800 /* Mode 8 */
-#define SDRAM_BXCF_M_AM_9 0x00000900 /* Mode 9 */
-#define SDRAM_BXCF_M_BE_MASK 0x00000001 /* Memory Bank Enable */
-#define SDRAM_BXCF_M_BE_DISABLE 0x00000000 /* Memory Bank Enable */
-#define SDRAM_BXCF_M_BE_ENABLE 0x00000001 /* Memory Bank Enable */
-
-#define SDRAM_RTSR_TRK1SM_MASK 0xC0000000 /* Tracking State Mach 1*/
-#define SDRAM_RTSR_TRK1SM_ATBASE 0x00000000 /* atbase state */
-#define SDRAM_RTSR_TRK1SM_MISSED 0x40000000 /* missed state */
-#define SDRAM_RTSR_TRK1SM_ATPLS1 0x80000000 /* atpls1 state */
-#define SDRAM_RTSR_TRK1SM_RESET 0xC0000000 /* reset state */
-
-#define SDR0_MFR_FIXD 0x10000000 /* Workaround for PCI/DMA */
-#endif /* CONFIG_440SPE */
-
-#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
-/*-----------------------------------------------------------------------------
- | SDRAM Controller
- +----------------------------------------------------------------------------*/
-#define DDR0_00 0x00
-#define DDR0_00_INT_ACK_MASK 0x7F000000 /* Write only */
-#define DDR0_00_INT_ACK_ALL 0x7F000000
-#define DDR0_00_INT_ACK_ENCODE(n) ((((unsigned long)(n))&0x7F)<<24)
-#define DDR0_00_INT_ACK_DECODE(n) ((((unsigned long)(n))>>24)&0x7F)
-/* Status */
-#define DDR0_00_INT_STATUS_MASK 0x00FF0000 /* Read only */
-/* Bit0. A single access outside the defined PHYSICAL memory space detected. */
-#define DDR0_00_INT_STATUS_BIT0 0x00010000
-/* Bit1. Multiple accesses outside the defined PHYSICAL memory space detected. */
-#define DDR0_00_INT_STATUS_BIT1 0x00020000
-/* Bit2. Single correctable ECC event detected */
-#define DDR0_00_INT_STATUS_BIT2 0x00040000
-/* Bit3. Multiple correctable ECC events detected. */
-#define DDR0_00_INT_STATUS_BIT3 0x00080000
-/* Bit4. Single uncorrectable ECC event detected. */
-#define DDR0_00_INT_STATUS_BIT4 0x00100000
-/* Bit5. Multiple uncorrectable ECC events detected. */
-#define DDR0_00_INT_STATUS_BIT5 0x00200000
-/* Bit6. DRAM initialization complete. */
-#define DDR0_00_INT_STATUS_BIT6 0x00400000
-/* Bit7. Logical OR of all lower bits. */
-#define DDR0_00_INT_STATUS_BIT7 0x00800000
-
-#define DDR0_00_INT_STATUS_ENCODE(n) ((((unsigned long)(n))&0xFF)<<16)
-#define DDR0_00_INT_STATUS_DECODE(n) ((((unsigned long)(n))>>16)&0xFF)
-#define DDR0_00_DLL_INCREMENT_MASK 0x00007F00
-#define DDR0_00_DLL_INCREMENT_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8)
-#define DDR0_00_DLL_INCREMENT_DECODE(n) ((((unsigned long)(n))>>8)&0x7F)
-#define DDR0_00_DLL_START_POINT_MASK 0x0000007F
-#define DDR0_00_DLL_START_POINT_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0)
-#define DDR0_00_DLL_START_POINT_DECODE(n) ((((unsigned long)(n))>>0)&0x7F)
-
-#define DDR0_01 0x01
-#define DDR0_01_PLB0_DB_CS_LOWER_MASK 0x1F000000
-#define DDR0_01_PLB0_DB_CS_LOWER_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24)
-#define DDR0_01_PLB0_DB_CS_LOWER_DECODE(n) ((((unsigned long)(n))>>24)&0x1F)
-#define DDR0_01_PLB0_DB_CS_UPPER_MASK 0x001F0000
-#define DDR0_01_PLB0_DB_CS_UPPER_ENCODE(n) ((((unsigned long)(n))&0x1F)<<16)
-#define DDR0_01_PLB0_DB_CS_UPPER_DECODE(n) ((((unsigned long)(n))>>16)&0x1F)
-#define DDR0_01_OUT_OF_RANGE_TYPE_MASK 0x00000700 /* Read only */
-#define DDR0_01_OUT_OF_RANGE_TYPE_ENCODE(n) ((((unsigned long)(n))&0x7)<<8)
-#define DDR0_01_OUT_OF_RANGE_TYPE_DECODE(n) ((((unsigned long)(n))>>8)&0x7)
-#define DDR0_01_INT_MASK_MASK 0x000000FF
-#define DDR0_01_INT_MASK_ENCODE(n) ((((unsigned long)(n))&0xFF)<<0)
-#define DDR0_01_INT_MASK_DECODE(n) ((((unsigned long)(n))>>0)&0xFF)
-#define DDR0_01_INT_MASK_ALL_ON 0x000000FF
-#define DDR0_01_INT_MASK_ALL_OFF 0x00000000
-
-#define DDR0_02 0x02
-#define DDR0_02_MAX_CS_REG_MASK 0x02000000 /* Read only */
-#define DDR0_02_MAX_CS_REG_ENCODE(n) ((((unsigned long)(n))&0x2)<<24)
-#define DDR0_02_MAX_CS_REG_DECODE(n) ((((unsigned long)(n))>>24)&0x2)
-#define DDR0_02_MAX_COL_REG_MASK 0x000F0000 /* Read only */
-#define DDR0_02_MAX_COL_REG_ENCODE(n) ((((unsigned long)(n))&0xF)<<16)
-#define DDR0_02_MAX_COL_REG_DECODE(n) ((((unsigned long)(n))>>16)&0xF)
-#define DDR0_02_MAX_ROW_REG_MASK 0x00000F00 /* Read only */
-#define DDR0_02_MAX_ROW_REG_ENCODE(n) ((((unsigned long)(n))&0xF)<<8)
-#define DDR0_02_MAX_ROW_REG_DECODE(n) ((((unsigned long)(n))>>8)&0xF)
-#define DDR0_02_START_MASK 0x00000001
-#define DDR0_02_START_ENCODE(n) ((((unsigned long)(n))&0x1)<<0)
-#define DDR0_02_START_DECODE(n) ((((unsigned long)(n))>>0)&0x1)
-#define DDR0_02_START_OFF 0x00000000
-#define DDR0_02_START_ON 0x00000001
-
-#define DDR0_03 0x03
-#define DDR0_03_BSTLEN_MASK 0x07000000
-#define DDR0_03_BSTLEN_ENCODE(n) ((((unsigned long)(n))&0x7)<<24)
-#define DDR0_03_BSTLEN_DECODE(n) ((((unsigned long)(n))>>24)&0x7)
-#define DDR0_03_CASLAT_MASK 0x00070000
-#define DDR0_03_CASLAT_ENCODE(n) ((((unsigned long)(n))&0x7)<<16)
-#define DDR0_03_CASLAT_DECODE(n) ((((unsigned long)(n))>>16)&0x7)
-#define DDR0_03_CASLAT_LIN_MASK 0x00000F00
-#define DDR0_03_CASLAT_LIN_ENCODE(n) ((((unsigned long)(n))&0xF)<<8)
-#define DDR0_03_CASLAT_LIN_DECODE(n) ((((unsigned long)(n))>>8)&0xF)
-#define DDR0_03_INITAREF_MASK 0x0000000F
-#define DDR0_03_INITAREF_ENCODE(n) ((((unsigned long)(n))&0xF)<<0)
-#define DDR0_03_INITAREF_DECODE(n) ((((unsigned long)(n))>>0)&0xF)
-
-#define DDR0_04 0x04
-#define DDR0_04_TRC_MASK 0x1F000000
-#define DDR0_04_TRC_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24)
-#define DDR0_04_TRC_DECODE(n) ((((unsigned long)(n))>>24)&0x1F)
-#define DDR0_04_TRRD_MASK 0x00070000
-#define DDR0_04_TRRD_ENCODE(n) ((((unsigned long)(n))&0x7)<<16)
-#define DDR0_04_TRRD_DECODE(n) ((((unsigned long)(n))>>16)&0x7)
-#define DDR0_04_TRTP_MASK 0x00000700
-#define DDR0_04_TRTP_ENCODE(n) ((((unsigned long)(n))&0x7)<<8)
-#define DDR0_04_TRTP_DECODE(n) ((((unsigned long)(n))>>8)&0x7)
-
-#define DDR0_05 0x05
-#define DDR0_05_TMRD_MASK 0x1F000000
-#define DDR0_05_TMRD_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24)
-#define DDR0_05_TMRD_DECODE(n) ((((unsigned long)(n))>>24)&0x1F)
-#define DDR0_05_TEMRS_MASK 0x00070000
-#define DDR0_05_TEMRS_ENCODE(n) ((((unsigned long)(n))&0x7)<<16)
-#define DDR0_05_TEMRS_DECODE(n) ((((unsigned long)(n))>>16)&0x7)
-#define DDR0_05_TRP_MASK 0x00000F00
-#define DDR0_05_TRP_ENCODE(n) ((((unsigned long)(n))&0xF)<<8)
-#define DDR0_05_TRP_DECODE(n) ((((unsigned long)(n))>>8)&0xF)
-#define DDR0_05_TRAS_MIN_MASK 0x000000FF
-#define DDR0_05_TRAS_MIN_ENCODE(n) ((((unsigned long)(n))&0xFF)<<0)
-#define DDR0_05_TRAS_MIN_DECODE(n) ((((unsigned long)(n))>>0)&0xFF)
-
-#define DDR0_06 0x06
-#define DDR0_06_WRITEINTERP_MASK 0x01000000
-#define DDR0_06_WRITEINTERP_ENCODE(n) ((((unsigned long)(n))&0x1)<<24)
-#define DDR0_06_WRITEINTERP_DECODE(n) ((((unsigned long)(n))>>24)&0x1)
-#define DDR0_06_TWTR_MASK 0x00070000
-#define DDR0_06_TWTR_ENCODE(n) ((((unsigned long)(n))&0x7)<<16)
-#define DDR0_06_TWTR_DECODE(n) ((((unsigned long)(n))>>16)&0x7)
-#define DDR0_06_TDLL_MASK 0x0000FF00
-#define DDR0_06_TDLL_ENCODE(n) ((((unsigned long)(n))&0xFF)<<8)
-#define DDR0_06_TDLL_DECODE(n) ((((unsigned long)(n))>>8)&0xFF)
-#define DDR0_06_TRFC_MASK 0x0000007F
-#define DDR0_06_TRFC_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0)
-#define DDR0_06_TRFC_DECODE(n) ((((unsigned long)(n))>>0)&0x7F)
-
-#define DDR0_07 0x07
-#define DDR0_07_NO_CMD_INIT_MASK 0x01000000
-#define DDR0_07_NO_CMD_INIT_ENCODE(n) ((((unsigned long)(n))&0x1)<<24)
-#define DDR0_07_NO_CMD_INIT_DECODE(n) ((((unsigned long)(n))>>24)&0x1)
-#define DDR0_07_TFAW_MASK 0x001F0000
-#define DDR0_07_TFAW_ENCODE(n) ((((unsigned long)(n))&0x1F)<<16)
-#define DDR0_07_TFAW_DECODE(n) ((((unsigned long)(n))>>16)&0x1F)
-#define DDR0_07_AUTO_REFRESH_MODE_MASK 0x00000100
-#define DDR0_07_AUTO_REFRESH_MODE_ENCODE(n) ((((unsigned long)(n))&0x1)<<8)
-#define DDR0_07_AUTO_REFRESH_MODE_DECODE(n) ((((unsigned long)(n))>>8)&0x1)
-#define DDR0_07_AREFRESH_MASK 0x00000001
-#define DDR0_07_AREFRESH_ENCODE(n) ((((unsigned long)(n))&0x1)<<0)
-#define DDR0_07_AREFRESH_DECODE(n) ((((unsigned long)(n))>>0)&0x1)
-
-#define DDR0_08 0x08
-#define DDR0_08_WRLAT_MASK 0x07000000
-#define DDR0_08_WRLAT_ENCODE(n) ((((unsigned long)(n))&0x7)<<24)
-#define DDR0_08_WRLAT_DECODE(n) ((((unsigned long)(n))>>24)&0x7)
-#define DDR0_08_TCPD_MASK 0x00FF0000
-#define DDR0_08_TCPD_ENCODE(n) ((((unsigned long)(n))&0xFF)<<16)
-#define DDR0_08_TCPD_DECODE(n) ((((unsigned long)(n))>>16)&0xFF)
-#define DDR0_08_DQS_N_EN_MASK 0x00000100
-#define DDR0_08_DQS_N_EN_ENCODE(n) ((((unsigned long)(n))&0x1)<<8)
-#define DDR0_08_DQS_N_EN_DECODE(n) ((((unsigned long)(n))>>8)&0x1)
-#define DDR0_08_DDRII_SDRAM_MODE_MASK 0x00000001
-#define DDR0_08_DDRII_ENCODE(n) ((((unsigned long)(n))&0x1)<<0)
-#define DDR0_08_DDRII_DECODE(n) ((((unsigned long)(n))>>0)&0x1)
-
-#define DDR0_09 0x09
-#define DDR0_09_OCD_ADJUST_PDN_CS_0_MASK 0x1F000000
-#define DDR0_09_OCD_ADJUST_PDN_CS_0_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24)
-#define DDR0_09_OCD_ADJUST_PDN_CS_0_DECODE(n) ((((unsigned long)(n))>>24)&0x1F)
-#define DDR0_09_RTT_0_MASK 0x00030000
-#define DDR0_09_RTT_0_ENCODE(n) ((((unsigned long)(n))&0x3)<<16)
-#define DDR0_09_RTT_0_DECODE(n) ((((unsigned long)(n))>>16)&0x3)
-#define DDR0_09_WR_DQS_SHIFT_BYPASS_MASK 0x00007F00
-#define DDR0_09_WR_DQS_SHIFT_BYPASS_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8)
-#define DDR0_09_WR_DQS_SHIFT_BYPASS_DECODE(n) ((((unsigned long)(n))>>8)&0x7F)
-#define DDR0_09_WR_DQS_SHIFT_MASK 0x0000007F
-#define DDR0_09_WR_DQS_SHIFT_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0)
-#define DDR0_09_WR_DQS_SHIFT_DECODE(n) ((((unsigned long)(n))>>0)&0x7F)
-
-#define DDR0_10 0x0A
-#define DDR0_10_WRITE_MODEREG_MASK 0x00010000 /* Write only */
-#define DDR0_10_WRITE_MODEREG_ENCODE(n) ((((unsigned long)(n))&0x1)<<16)
-#define DDR0_10_WRITE_MODEREG_DECODE(n) ((((unsigned long)(n))>>16)&0x1)
-#define DDR0_10_CS_MAP_MASK 0x00000300
-#define DDR0_10_CS_MAP_NO_MEM 0x00000000
-#define DDR0_10_CS_MAP_RANK0_INSTALLED 0x00000100
-#define DDR0_10_CS_MAP_RANK1_INSTALLED 0x00000200
-#define DDR0_10_CS_MAP_ENCODE(n) ((((unsigned long)(n))&0x3)<<8)
-#define DDR0_10_CS_MAP_DECODE(n) ((((unsigned long)(n))>>8)&0x3)
-#define DDR0_10_OCD_ADJUST_PUP_CS_0_MASK 0x0000001F
-#define DDR0_10_OCD_ADJUST_PUP_CS_0_ENCODE(n) ((((unsigned long)(n))&0x1F)<<0)
-#define DDR0_10_OCD_ADJUST_PUP_CS_0_DECODE(n) ((((unsigned long)(n))>>0)&0x1F)
-
-#define DDR0_11 0x0B
-#define DDR0_11_SREFRESH_MASK 0x01000000
-#define DDR0_11_SREFRESH_ENCODE(n) ((((unsigned long)(n))&0x1)<<24)
-#define DDR0_11_SREFRESH_DECODE(n) ((((unsigned long)(n))>>24)&0x1F)
-#define DDR0_11_TXSNR_MASK 0x00FF0000
-#define DDR0_11_TXSNR_ENCODE(n) ((((unsigned long)(n))&0xFF)<<16)
-#define DDR0_11_TXSNR_DECODE(n) ((((unsigned long)(n))>>16)&0xFF)
-#define DDR0_11_TXSR_MASK 0x0000FF00
-#define DDR0_11_TXSR_ENCODE(n) ((((unsigned long)(n))&0xFF)<<8)
-#define DDR0_11_TXSR_DECODE(n) ((((unsigned long)(n))>>8)&0xFF)
-
-#define DDR0_12 0x0C
-#define DDR0_12_TCKE_MASK 0x0000007
-#define DDR0_12_TCKE_ENCODE(n) ((((unsigned long)(n))&0x7)<<0)
-#define DDR0_12_TCKE_DECODE(n) ((((unsigned long)(n))>>0)&0x7)
-
-#define DDR0_14 0x0E
-#define DDR0_14_DLL_BYPASS_MODE_MASK 0x01000000
-#define DDR0_14_DLL_BYPASS_MODE_ENCODE(n) ((((unsigned long)(n))&0x1)<<24)
-#define DDR0_14_DLL_BYPASS_MODE_DECODE(n) ((((unsigned long)(n))>>24)&0x1)
-#define DDR0_14_REDUC_MASK 0x00010000
-#define DDR0_14_REDUC_64BITS 0x00000000
-#define DDR0_14_REDUC_32BITS 0x00010000
-#define DDR0_14_REDUC_ENCODE(n) ((((unsigned long)(n))&0x1)<<16)
-#define DDR0_14_REDUC_DECODE(n) ((((unsigned long)(n))>>16)&0x1)
-#define DDR0_14_REG_DIMM_ENABLE_MASK 0x00000100
-#define DDR0_14_REG_DIMM_ENABLE_ENCODE(n) ((((unsigned long)(n))&0x1)<<8)
-#define DDR0_14_REG_DIMM_ENABLE_DECODE(n) ((((unsigned long)(n))>>8)&0x1)
-
-#define DDR0_17 0x11
-#define DDR0_17_DLL_DQS_DELAY_0_MASK 0x7F000000
-#define DDR0_17_DLL_DQS_DELAY_0_ENCODE(n) ((((unsigned long)(n))&0x7F)<<24)
-#define DDR0_17_DLL_DQS_DELAY_0_DECODE(n) ((((unsigned long)(n))>>24)&0x7F)
-#define DDR0_17_DLLLOCKREG_MASK 0x00010000 /* Read only */
-#define DDR0_17_DLLLOCKREG_LOCKED 0x00010000
-#define DDR0_17_DLLLOCKREG_UNLOCKED 0x00000000
-#define DDR0_17_DLLLOCKREG_ENCODE(n) ((((unsigned long)(n))&0x1)<<16)
-#define DDR0_17_DLLLOCKREG_DECODE(n) ((((unsigned long)(n))>>16)&0x1)
-#define DDR0_17_DLL_LOCK_MASK 0x00007F00 /* Read only */
-#define DDR0_17_DLL_LOCK_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8)
-#define DDR0_17_DLL_LOCK_DECODE(n) ((((unsigned long)(n))>>8)&0x7F)
-
-#define DDR0_18 0x12
-#define DDR0_18_DLL_DQS_DELAY_X_MASK 0x7F7F7F7F
-#define DDR0_18_DLL_DQS_DELAY_4_MASK 0x7F000000
-#define DDR0_18_DLL_DQS_DELAY_4_ENCODE(n) ((((unsigned long)(n))&0x7F)<<24)
-#define DDR0_18_DLL_DQS_DELAY_4_DECODE(n) ((((unsigned long)(n))>>24)&0x7F)
-#define DDR0_18_DLL_DQS_DELAY_3_MASK 0x007F0000
-#define DDR0_18_DLL_DQS_DELAY_3_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16)
-#define DDR0_18_DLL_DQS_DELAY_3_DECODE(n) ((((unsigned long)(n))>>16)&0x7F)
-#define DDR0_18_DLL_DQS_DELAY_2_MASK 0x00007F00
-#define DDR0_18_DLL_DQS_DELAY_2_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8)
-#define DDR0_18_DLL_DQS_DELAY_2_DECODE(n) ((((unsigned long)(n))>>8)&0x7F)
-#define DDR0_18_DLL_DQS_DELAY_1_MASK 0x0000007F
-#define DDR0_18_DLL_DQS_DELAY_1_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0)
-#define DDR0_18_DLL_DQS_DELAY_1_DECODE(n) ((((unsigned long)(n))>>0)&0x7F)
-
-#define DDR0_19 0x13
-#define DDR0_19_DLL_DQS_DELAY_X_MASK 0x7F7F7F7F
-#define DDR0_19_DLL_DQS_DELAY_8_MASK 0x7F000000
-#define DDR0_19_DLL_DQS_DELAY_8_ENCODE(n) ((((unsigned long)(n))&0x7F)<<24)
-#define DDR0_19_DLL_DQS_DELAY_8_DECODE(n) ((((unsigned long)(n))>>24)&0x7F)
-#define DDR0_19_DLL_DQS_DELAY_7_MASK 0x007F0000
-#define DDR0_19_DLL_DQS_DELAY_7_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16)
-#define DDR0_19_DLL_DQS_DELAY_7_DECODE(n) ((((unsigned long)(n))>>16)&0x7F)
-#define DDR0_19_DLL_DQS_DELAY_6_MASK 0x00007F00
-#define DDR0_19_DLL_DQS_DELAY_6_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8)
-#define DDR0_19_DLL_DQS_DELAY_6_DECODE(n) ((((unsigned long)(n))>>8)&0x7F)
-#define DDR0_19_DLL_DQS_DELAY_5_MASK 0x0000007F
-#define DDR0_19_DLL_DQS_DELAY_5_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0)
-#define DDR0_19_DLL_DQS_DELAY_5_DECODE(n) ((((unsigned long)(n))>>0)&0x7F)
-
-#define DDR0_20 0x14
-#define DDR0_20_DLL_DQS_BYPASS_3_MASK 0x7F000000
-#define DDR0_20_DLL_DQS_BYPASS_3_ENCODE(n) ((((unsigned long)(n))&0x7F)<<24)
-#define DDR0_20_DLL_DQS_BYPASS_3_DECODE(n) ((((unsigned long)(n))>>24)&0x7F)
-#define DDR0_20_DLL_DQS_BYPASS_2_MASK 0x007F0000
-#define DDR0_20_DLL_DQS_BYPASS_2_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16)
-#define DDR0_20_DLL_DQS_BYPASS_2_DECODE(n) ((((unsigned long)(n))>>16)&0x7F)
-#define DDR0_20_DLL_DQS_BYPASS_1_MASK 0x00007F00
-#define DDR0_20_DLL_DQS_BYPASS_1_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8)
-#define DDR0_20_DLL_DQS_BYPASS_1_DECODE(n) ((((unsigned long)(n))>>8)&0x7F)
-#define DDR0_20_DLL_DQS_BYPASS_0_MASK 0x0000007F
-#define DDR0_20_DLL_DQS_BYPASS_0_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0)
-#define DDR0_20_DLL_DQS_BYPASS_0_DECODE(n) ((((unsigned long)(n))>>0)&0x7F)
-
-#define DDR0_21 0x15
-#define DDR0_21_DLL_DQS_BYPASS_7_MASK 0x7F000000
-#define DDR0_21_DLL_DQS_BYPASS_7_ENCODE(n) ((((unsigned long)(n))&0x7F)<<24)
-#define DDR0_21_DLL_DQS_BYPASS_7_DECODE(n) ((((unsigned long)(n))>>24)&0x7F)
-#define DDR0_21_DLL_DQS_BYPASS_6_MASK 0x007F0000
-#define DDR0_21_DLL_DQS_BYPASS_6_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16)
-#define DDR0_21_DLL_DQS_BYPASS_6_DECODE(n) ((((unsigned long)(n))>>16)&0x7F)
-#define DDR0_21_DLL_DQS_BYPASS_5_MASK 0x00007F00
-#define DDR0_21_DLL_DQS_BYPASS_5_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8)
-#define DDR0_21_DLL_DQS_BYPASS_5_DECODE(n) ((((unsigned long)(n))>>8)&0x7F)
-#define DDR0_21_DLL_DQS_BYPASS_4_MASK 0x0000007F
-#define DDR0_21_DLL_DQS_BYPASS_4_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0)
-#define DDR0_21_DLL_DQS_BYPASS_4_DECODE(n) ((((unsigned long)(n))>>0)&0x7F)
-
-#define DDR0_22 0x16
-#define DDR0_22_CTRL_RAW_MASK 0x03000000
-#define DDR0_22_CTRL_RAW_ECC_DISABLE 0x00000000 /* ECC not being used */
-#define DDR0_22_CTRL_RAW_ECC_CHECK_ONLY 0x01000000 /* ECC checking is on, but no attempts to correct */
-#define DDR0_22_CTRL_RAW_NO_ECC_RAM 0x02000000 /* No ECC RAM storage available */
-#define DDR0_22_CTRL_RAW_ECC_ENABLE 0x03000000 /* ECC checking and correcting on */
-#define DDR0_22_CTRL_RAW_ENCODE(n) ((((unsigned long)(n))&0x3)<<24)
-#define DDR0_22_CTRL_RAW_DECODE(n) ((((unsigned long)(n))>>24)&0x3)
-#define DDR0_22_DQS_OUT_SHIFT_BYPASS_MASK 0x007F0000
-#define DDR0_22_DQS_OUT_SHIFT_BYPASS_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16)
-#define DDR0_22_DQS_OUT_SHIFT_BYPASS_DECODE(n) ((((unsigned long)(n))>>16)&0x7F)
-#define DDR0_22_DQS_OUT_SHIFT_MASK 0x00007F00
-#define DDR0_22_DQS_OUT_SHIFT_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8)
-#define DDR0_22_DQS_OUT_SHIFT_DECODE(n) ((((unsigned long)(n))>>8)&0x7F)
-#define DDR0_22_DLL_DQS_BYPASS_8_MASK 0x0000007F
-#define DDR0_22_DLL_DQS_BYPASS_8_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0)
-#define DDR0_22_DLL_DQS_BYPASS_8_DECODE(n) ((((unsigned long)(n))>>0)&0x7F)
-
-#define DDR0_23 0x17
-#define DDR0_23_ODT_RD_MAP_CS0_MASK 0x03000000
-#define DDR0_23_ODT_RD_MAP_CS0_ENCODE(n) ((((unsigned long)(n))&0x3)<<24)
-#define DDR0_23_ODT_RD_MAP_CS0_DECODE(n) ((((unsigned long)(n))>>24)&0x3)
-#define DDR0_23_ECC_C_SYND_MASK 0x00FF0000 /* Read only */
-#define DDR0_23_ECC_C_SYND_ENCODE(n) ((((unsigned long)(n))&0xFF)<<16)
-#define DDR0_23_ECC_C_SYND_DECODE(n) ((((unsigned long)(n))>>16)&0xFF)
-#define DDR0_23_ECC_U_SYND_MASK 0x0000FF00 /* Read only */
-#define DDR0_23_ECC_U_SYND_ENCODE(n) ((((unsigned long)(n))&0xFF)<<8)
-#define DDR0_23_ECC_U_SYND_DECODE(n) ((((unsigned long)(n))>>8)&0xFF)
-#define DDR0_23_FWC_MASK 0x00000001 /* Write only */
-#define DDR0_23_FWC_ENCODE(n) ((((unsigned long)(n))&0x1)<<0)
-#define DDR0_23_FWC_DECODE(n) ((((unsigned long)(n))>>0)&0x1)
-
-#define DDR0_24 0x18
-#define DDR0_24_RTT_PAD_TERMINATION_MASK 0x03000000
-#define DDR0_24_RTT_PAD_TERMINATION_ENCODE(n) ((((unsigned long)(n))&0x3)<<24)
-#define DDR0_24_RTT_PAD_TERMINATION_DECODE(n) ((((unsigned long)(n))>>24)&0x3)
-#define DDR0_24_ODT_WR_MAP_CS1_MASK 0x00030000
-#define DDR0_24_ODT_WR_MAP_CS1_ENCODE(n) ((((unsigned long)(n))&0x3)<<16)
-#define DDR0_24_ODT_WR_MAP_CS1_DECODE(n) ((((unsigned long)(n))>>16)&0x3)
-#define DDR0_24_ODT_RD_MAP_CS1_MASK 0x00000300
-#define DDR0_24_ODT_RD_MAP_CS1_ENCODE(n) ((((unsigned long)(n))&0x3)<<8)
-#define DDR0_24_ODT_RD_MAP_CS1_DECODE(n) ((((unsigned long)(n))>>8)&0x3)
-#define DDR0_24_ODT_WR_MAP_CS0_MASK 0x00000003
-#define DDR0_24_ODT_WR_MAP_CS0_ENCODE(n) ((((unsigned long)(n))&0x3)<<0)
-#define DDR0_24_ODT_WR_MAP_CS0_DECODE(n) ((((unsigned long)(n))>>0)&0x3)
-
-#define DDR0_25 0x19
-#define DDR0_25_VERSION_MASK 0xFFFF0000 /* Read only */
-#define DDR0_25_VERSION_ENCODE(n) ((((unsigned long)(n))&0xFFFF)<<16)
-#define DDR0_25_VERSION_DECODE(n) ((((unsigned long)(n))>>16)&0xFFFF)
-#define DDR0_25_OUT_OF_RANGE_LENGTH_MASK 0x000003FF /* Read only */
-#define DDR0_25_OUT_OF_RANGE_LENGTH_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<0)
-#define DDR0_25_OUT_OF_RANGE_LENGTH_DECODE(n) ((((unsigned long)(n))>>0)&0x3FF)
-
-#define DDR0_26 0x1A
-#define DDR0_26_TRAS_MAX_MASK 0xFFFF0000
-#define DDR0_26_TRAS_MAX_ENCODE(n) ((((unsigned long)(n))&0xFFFF)<<16)
-#define DDR0_26_TRAS_MAX_DECODE(n) ((((unsigned long)(n))>>16)&0xFFFF)
-#define DDR0_26_TREF_MASK 0x00003FFF
-#define DDR0_26_TREF_ENCODE(n) ((((unsigned long)(n))&0x3FFF)<<0)
-#define DDR0_26_TREF_DECODE(n) ((((unsigned long)(n))>>0)&0x3FFF)
-
-#define DDR0_27 0x1B
-#define DDR0_27_EMRS_DATA_MASK 0x3FFF0000
-#define DDR0_27_EMRS_DATA_ENCODE(n) ((((unsigned long)(n))&0x3FFF)<<16)
-#define DDR0_27_EMRS_DATA_DECODE(n) ((((unsigned long)(n))>>16)&0x3FFF)
-#define DDR0_27_TINIT_MASK 0x0000FFFF
-#define DDR0_27_TINIT_ENCODE(n) ((((unsigned long)(n))&0xFFFF)<<0)
-#define DDR0_27_TINIT_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFF)
-
-#define DDR0_28 0x1C
-#define DDR0_28_EMRS3_DATA_MASK 0x3FFF0000
-#define DDR0_28_EMRS3_DATA_ENCODE(n) ((((unsigned long)(n))&0x3FFF)<<16)
-#define DDR0_28_EMRS3_DATA_DECODE(n) ((((unsigned long)(n))>>16)&0x3FFF)
-#define DDR0_28_EMRS2_DATA_MASK 0x00003FFF
-#define DDR0_28_EMRS2_DATA_ENCODE(n) ((((unsigned long)(n))&0x3FFF)<<0)
-#define DDR0_28_EMRS2_DATA_DECODE(n) ((((unsigned long)(n))>>0)&0x3FFF)
-
-#define DDR0_31 0x1F
-#define DDR0_31_XOR_CHECK_BITS_MASK 0x0000FFFF
-#define DDR0_31_XOR_CHECK_BITS_ENCODE(n) ((((unsigned long)(n))&0xFFFF)<<0)
-#define DDR0_31_XOR_CHECK_BITS_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFF)
-
-#define DDR0_32 0x20
-#define DDR0_32_OUT_OF_RANGE_ADDR_MASK 0xFFFFFFFF /* Read only */
-#define DDR0_32_OUT_OF_RANGE_ADDR_ENCODE(n) ((((unsigned long)(n))&0xFFFFFFFF)<<0)
-#define DDR0_32_OUT_OF_RANGE_ADDR_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFFFFFF)
-
-#define DDR0_33 0x21
-#define DDR0_33_OUT_OF_RANGE_ADDR_MASK 0x00000001 /* Read only */
-#define DDR0_33_OUT_OF_RANGE_ADDR_ENCODE(n) ((((unsigned long)(n))&0x1)<<0)
-#define DDR0_33_OUT_OF_RANGE_ADDR_DECODE(n) ((((unsigned long)(n))>>0)&0x1)
-
-#define DDR0_34 0x22
-#define DDR0_34_ECC_U_ADDR_MASK 0xFFFFFFFF /* Read only */
-#define DDR0_34_ECC_U_ADDR_ENCODE(n) ((((unsigned long)(n))&0xFFFFFFFF)<<0)
-#define DDR0_34_ECC_U_ADDR_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFFFFFF)
-
-#define DDR0_35 0x23
-#define DDR0_35_ECC_U_ADDR_MASK 0x00000001 /* Read only */
-#define DDR0_35_ECC_U_ADDR_ENCODE(n) ((((unsigned long)(n))&0x1)<<0)
-#define DDR0_35_ECC_U_ADDR_DECODE(n) ((((unsigned long)(n))>>0)&0x1)
-
-#define DDR0_36 0x24
-#define DDR0_36_ECC_U_DATA_MASK 0xFFFFFFFF /* Read only */
-#define DDR0_36_ECC_U_DATA_ENCODE(n) ((((unsigned long)(n))&0xFFFFFFFF)<<0)
-#define DDR0_36_ECC_U_DATA_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFFFFFF)
-
-#define DDR0_37 0x25
-#define DDR0_37_ECC_U_DATA_MASK 0xFFFFFFFF /* Read only */
-#define DDR0_37_ECC_U_DATA_ENCODE(n) ((((unsigned long)(n))&0xFFFFFFFF)<<0)
-#define DDR0_37_ECC_U_DATA_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFFFFFF)
-
-#define DDR0_38 0x26
-#define DDR0_38_ECC_C_ADDR_MASK 0xFFFFFFFF /* Read only */
-#define DDR0_38_ECC_C_ADDR_ENCODE(n) ((((unsigned long)(n))&0xFFFFFFFF)<<0)
-#define DDR0_38_ECC_C_ADDR_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFFFFFF)
-
-#define DDR0_39 0x27
-#define DDR0_39_ECC_C_ADDR_MASK 0x00000001 /* Read only */
-#define DDR0_39_ECC_C_ADDR_ENCODE(n) ((((unsigned long)(n))&0x1)<<0)
-#define DDR0_39_ECC_C_ADDR_DECODE(n) ((((unsigned long)(n))>>0)&0x1)
-
-#define DDR0_40 0x28
-#define DDR0_40_ECC_C_DATA_MASK 0xFFFFFFFF /* Read only */
-#define DDR0_40_ECC_C_DATA_ENCODE(n) ((((unsigned long)(n))&0xFFFFFFFF)<<0)
-#define DDR0_40_ECC_C_DATA_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFFFFFF)
-
-#define DDR0_41 0x29
-#define DDR0_41_ECC_C_DATA_MASK 0xFFFFFFFF /* Read only */
-#define DDR0_41_ECC_C_DATA_ENCODE(n) ((((unsigned long)(n))&0xFFFFFFFF)<<0)
-#define DDR0_41_ECC_C_DATA_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFFFFFF)
-
-#define DDR0_42 0x2A
-#define DDR0_42_ADDR_PINS_MASK 0x07000000
-#define DDR0_42_ADDR_PINS_ENCODE(n) ((((unsigned long)(n))&0x7)<<24)
-#define DDR0_42_ADDR_PINS_DECODE(n) ((((unsigned long)(n))>>24)&0x7)
-#define DDR0_42_CASLAT_LIN_GATE_MASK 0x0000000F
-#define DDR0_42_CASLAT_LIN_GATE_ENCODE(n) ((((unsigned long)(n))&0xF)<<0)
-#define DDR0_42_CASLAT_LIN_GATE_DECODE(n) ((((unsigned long)(n))>>0)&0xF)
-
-#define DDR0_43 0x2B
-#define DDR0_43_TWR_MASK 0x07000000
-#define DDR0_43_TWR_ENCODE(n) ((((unsigned long)(n))&0x7)<<24)
-#define DDR0_43_TWR_DECODE(n) ((((unsigned long)(n))>>24)&0x7)
-#define DDR0_43_APREBIT_MASK 0x000F0000
-#define DDR0_43_APREBIT_ENCODE(n) ((((unsigned long)(n))&0xF)<<16)
-#define DDR0_43_APREBIT_DECODE(n) ((((unsigned long)(n))>>16)&0xF)
-#define DDR0_43_COLUMN_SIZE_MASK 0x00000700
-#define DDR0_43_COLUMN_SIZE_ENCODE(n) ((((unsigned long)(n))&0x7)<<8)
-#define DDR0_43_COLUMN_SIZE_DECODE(n) ((((unsigned long)(n))>>8)&0x7)
-#define DDR0_43_EIGHT_BANK_MODE_MASK 0x00000001
-#define DDR0_43_EIGHT_BANK_MODE_8_BANKS 0x00000001
-#define DDR0_43_EIGHT_BANK_MODE_4_BANKS 0x00000000
-#define DDR0_43_EIGHT_BANK_MODE_ENCODE(n) ((((unsigned long)(n))&0x1)<<0)
-#define DDR0_43_EIGHT_BANK_MODE_DECODE(n) ((((unsigned long)(n))>>0)&0x1)
-
-#define DDR0_44 0x2C
-#define DDR0_44_TRCD_MASK 0x000000FF
-#define DDR0_44_TRCD_ENCODE(n) ((((unsigned long)(n))&0xFF)<<0)
-#define DDR0_44_TRCD_DECODE(n) ((((unsigned long)(n))>>0)&0xFF)
-
-#endif /* CONFIG_440EPX */
-
/*-----------------------------------------------------------------------------
| External Bus Controller
+----------------------------------------------------------------------------*/
#ifndef __PPC4XX_H__
#define __PPC4XX_H__
+/*
+ * Configure which SDRAM/DDR/DDR2 controller is equipped
+ */
+#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_405EP) || \
+ defined(CONFIG_AP1000) || defined(CONFIG_ML2)
+#define CONFIG_SDRAM_PPC4xx_IBM_SDRAM /* IBM SDRAM controller */
+#endif
+
+#if defined(CONFIG_440GP) || defined(CONFIG_440GX) || \
+ defined(CONFIG_440EP) || defined(CONFIG_440GR)
+#define CONFIG_SDRAM_PPC4xx_IBM_DDR /* IBM DDR controller */
+#endif
+
+#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
+#define CONFIG_SDRAM_PPC4xx_DENALI_DDR2 /* Denali DDR(2) controller */
+#endif
+
+#if defined(CONFIG_405EX) || \
+ defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT)
+#define CONFIG_SDRAM_PPC4xx_IBM_DDR2 /* IBM DDR(2) controller */
+#endif
+
#if defined(CONFIG_440)
#include <ppc440.h>
#else
#include <ppc405.h>
#endif
+#include <asm/ppc4xx-sdram.h>
+
+/*
+ * Macro for generating register field mnemonics
+ */
+#define PPC_REG_BITS 32
+#define PPC_REG_VAL(bit, value) ((value) << ((PPC_REG_BITS - 1) - (bit)))
+
+/*
+ * Elide casts when assembling register mnemonics
+ */
+#ifndef __ASSEMBLY__
+#define static_cast(type, val) (type)(val)
+#else
+#define static_cast(type, val) (val)
+#endif
+
/*
* Common stuff for 4xx (405 and 440)
*/
$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
$(nandobj)u-boot-spl: $(OBJS)
- cd $(LNDIR) && $(LD) $(LDFLAGS) $$UNDEF_SYM $(__OBJS) \
+ cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \
-Map $(nandobj)u-boot-spl.map \
-o $(nandobj)u-boot-spl
$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
$(nandobj)u-boot-spl: $(OBJS)
- cd $(LNDIR) && $(LD) $(LDFLAGS) $$UNDEF_SYM $(__OBJS) \
+ cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \
-Map $(nandobj)u-boot-spl.map \
-o $(nandobj)u-boot-spl
}
/*
- * early_sdram_init()
+ * long int initdram(int board_type)
*
* As the name already indicates, this function is called very early
* from start.S and configures the SDRAM with fixed values. This is needed,
* modules are still plugged in. So it is recommended to remove the DIMM
* modules while using the NAND booting code with the fixed SDRAM setup!
*/
-void early_sdram_init(void)
+long int initdram(int board_type)
{
/*
* Soft-reset SDRAM controller.
*/
mtsdram(mem_cfg0, 0x80000000); /* DCEN=1, PMUD=0*/
wait_init_complete();
-}
-long int initdram(int board_type)
-{
- /*
- * Nothing to do here, just return size of fixed SDRAM setup
- */
return CFG_MBYTES_SDRAM << 20;
}
$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
$(nandobj)u-boot-spl: $(OBJS)
- cd $(LNDIR) && $(LD) $(LDFLAGS) $$UNDEF_SYM $(__OBJS) \
+ cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \
-Map $(nandobj)u-boot-spl.map \
-o $(nandobj)u-boot-spl
AFLAGS += -DCONFIG_NAND_SPL
CFLAGS += -DCONFIG_NAND_SPL
-SOBJS = start.o init.o resetvec.o cache.o
-COBJS = memory.o nand_boot.o nand_ecc.o ndfc.o
+SOBJS = start.o resetvec.o cache.o
+COBJS = 44x_spd_ddr2.o nand_boot.o nand_ecc.o ndfc.o
SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
$(nandobj)u-boot-spl: $(OBJS)
- cd $(LNDIR) && $(LD) $(LDFLAGS) $$UNDEF_SYM $(__OBJS) \
+ cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \
-Map $(nandobj)u-boot-spl.map \
-o $(nandobj)u-boot-spl
# create symbolic links for common files
# from cpu directory
+$(obj)44x_spd_ddr2.c: ecc.h
+ @rm -f $(obj)44x_spd_ddr2.c
+ ln -s $(SRCTREE)/cpu/ppc4xx/44x_spd_ddr2.c $(obj)44x_spd_ddr2.c
+
$(obj)cache.S:
@rm -f $(obj)cache.S
ln -s $(SRCTREE)/cpu/ppc4xx/cache.S $(obj)cache.S
+$(obj)ecc.h:
+ @rm -f $(obj)ecc.h
+ ln -s $(SRCTREE)/cpu/ppc4xx/ecc.h $(obj)ecc.h
+
$(obj)ndfc.c:
@rm -f $(obj)ndfc.c
ln -s $(SRCTREE)/cpu/ppc4xx/ndfc.c $(obj)ndfc.c
@rm -f $(obj)start.S
ln -s $(SRCTREE)/cpu/ppc4xx/start.S $(obj)start.S
-# from board directory
-$(obj)init.S:
- @rm -f $(obj)init.S
- ln -s $(SRCTREE)/board/amcc/kilauea/init.S $(obj)init.S
-
-$(obj)memory.c:
- @rm -f $(obj)memory.c
- ln -s $(SRCTREE)/board/amcc/kilauea/memory.c $(obj)memory.c
-
# from nand_spl directory
$(obj)nand_boot.c:
@rm -f $(obj)nand_boot.c
#
# On 4xx platforms the SPL is located at 0xfffff000...0xffffffff,
# in the last 4kBytes of memory space in cache.
-# We will copy this SPL into instruction-cache in start.S. So we set
-# TEXT_BASE to starting address in i-cache here.
+# We will copy this SPL into SDRAM since we can't access the NAND
+# controller at CS0 while running from this location. So we set
+# TEXT_BASE to starting address in SDRAM here.
#
TEXT_BASE = 0x00800000
.text :
{
start.o (.text)
- init.o (.text)
nand_boot.o (.text)
ndfc.o (.text)
$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
$(nandobj)u-boot-spl: $(OBJS)
- cd $(LNDIR) && $(LD) $(LDFLAGS) $$UNDEF_SYM $(__OBJS) \
+ cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \
-Map $(nandobj)u-boot-spl.map \
-o $(nandobj)u-boot-spl
return 0;
}
+/*
+ * The main entry for NAND booting. It's necessary that SDRAM is already
+ * configured and available since this code loads the main U-Boot image
+ * from NAND into SDRAM and starts it from there.
+ */
void nand_boot(void)
{
- ulong mem_size;
struct nand_chip nand_chip;
nand_info_t nand_info;
int ret;
void (*uboot)(void);
- /*
- * Init sdram, so we have access to memory
- */
- mem_size = initdram(0);
-
/*
* Init board specific nand support
*/
#define UDIV_SUBTRACT 0
#define UART0_SDR sdr_uart0
#define UART1_SDR sdr_uart1
-#if defined(CONFIG_440EP) || defined(CONFIG_440EPx) || \
- defined(CONFIG_440GR) || defined(CONFIG_440GRx) || \
- defined(CONFIG_440SP) || defined(CONFIG_440SPe)
+#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
+ defined(CONFIG_440GR) || defined(CONFIG_440GRX) || \
+ defined(CONFIG_440SP) || defined(CONFIG_440SPE)
#define UART2_SDR sdr_uart2
#endif
-#if defined(CONFIG_440EP) || defined(CONFIG_440EPx) || \
- defined(CONFIG_440GR) || defined(CONFIG_440GRx)
+#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
+ defined(CONFIG_440GR) || defined(CONFIG_440GRX)
#define UART3_SDR sdr_uart3
#endif
#define MFREG(a, d) mfsdr(a, d)
projects / people / ms / u-boot.git / commitdiff
