If you do not have i2c muxes on your board, omit this define.
-- Legacy I2C Support: CONFIG_HARD_I2C
-
- NOTE: It is intended to move drivers to CONFIG_SYS_I2C which
- provides the following compelling advantages:
-
- - more than one i2c adapter is usable
- - approved multibus support
- - better i2c mux support
-
- ** Please consider updating your I2C driver now. **
-
- These enable legacy I2C serial bus commands. Defining
- CONFIG_HARD_I2C will include the appropriate I2C driver
- for the selected CPU.
-
- This will allow you to use i2c commands at the u-boot
- command line (as long as you set CONFIG_CMD_I2C in
- CONFIG_COMMANDS) and communicate with i2c based realtime
- clock chips. See common/cmd_i2c.c for a description of the
- command line interface.
-
- CONFIG_HARD_I2C selects a hardware I2C controller.
-
- There are several other quantities that must also be
- defined when you define CONFIG_HARD_I2C.
-
- In both cases you will need to define CONFIG_SYS_I2C_SPEED
- to be the frequency (in Hz) at which you wish your i2c bus
- to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
- the CPU's i2c node address).
-
- Now, the u-boot i2c code for the mpc8xx
- (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
- and so its address should therefore be cleared to 0 (See,
- eg, MPC823e User's Manual p.16-473). So, set
- CONFIG_SYS_I2C_SLAVE to 0.
-
- CONFIG_SYS_I2C_INIT_MPC5XXX
-
- When a board is reset during an i2c bus transfer
- chips might think that the current transfer is still
- in progress. Reset the slave devices by sending start
- commands until the slave device responds.
-
- That's all that's required for CONFIG_HARD_I2C.
-
+- Legacy I2C Support:
If you use the software i2c interface (CONFIG_SYS_I2C_SOFT)
then the following macros need to be defined (examples are
from include/configs/lwmon.h):
custom i2c_init_board() routine in boards/xxx/board.c
is run early in the boot sequence.
- CONFIG_SYS_I2C_BOARD_LATE_INIT
-
- An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
- defined a custom i2c_board_late_init() routine in
- boards/xxx/board.c is run AFTER the operations in i2c_init()
- is completed. This callpoint can be used to unreset i2c bus
- using CPU i2c controller register accesses for CPUs whose i2c
- controller provide such a method. It is called at the end of
- i2c_init() to allow i2c_init operations to setup the i2c bus
- controller on the CPU (e.g. setting bus speed & slave address).
-
- CONFIG_I2CFAST (PPC405GP|PPC405EP only)
-
- This option enables configuration of bi_iic_fast[] flags
- in u-boot bd_info structure based on u-boot environment
- variable "i2cfast". (see also i2cfast)
-
CONFIG_I2C_MULTI_BUS
This option allows the use of multiple I2C buses, each of which
If defined, don't allow the -f switch to env set override variable
access flags.
-- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
- This is set by OMAP boards for the max time that reset should
- be asserted. See doc/README.omap-reset-time for details on how
- the value can be calculated on a given board.
-
- CONFIG_USE_STDINT
If stdint.h is available with your toolchain you can define this
option to enable it. You can provide option 'USE_STDINT=1' when
select DM_GPIO
select DM_SPI
select DM_SPI_FLASH
+ select USB_EHCI_HCD
config XTENSA
bool "Xtensa architecture"
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = timer.o
-obj-$(CONFIG_DISPLAY_CPUINFO) += cpuinfo.o
-obj-y += reset.o
+++ /dev/null
-/*
- * OMAP1 CPU identification code
- *
- * Copyright (C) 2004 Nokia Corporation
- * Written by Tony Lindgren <tony@atomide.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <common.h>
-#include <command.h>
-#include <linux/compiler.h>
-
-#if defined(CONFIG_OMAP)
-
-#define omap_readw(x) *(volatile unsigned short *)(x)
-#define omap_readl(x) *(volatile unsigned long *)(x)
-
-#define OMAP_DIE_ID_0 0xfffe1800
-#define OMAP_DIE_ID_1 0xfffe1804
-#define OMAP_PRODUCTION_ID_0 0xfffe2000
-#define OMAP_PRODUCTION_ID_1 0xfffe2004
-#define OMAP32_ID_0 0xfffed400
-#define OMAP32_ID_1 0xfffed404
-
-struct omap_id {
- u16 jtag_id; /* Used to determine OMAP type */
- u8 die_rev; /* Processor revision */
- u32 omap_id; /* OMAP revision */
- u32 type; /* Cpu id bits [31:08], cpu class bits [07:00] */
-};
-
-/* Register values to detect the OMAP version */
-static struct omap_id omap_ids[] = {
- { .jtag_id = 0xb574, .die_rev = 0x2, .omap_id = 0x03310315, .type = 0x03100000},
- { .jtag_id = 0x355f, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x07300100},
- { .jtag_id = 0xb55f, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x07300300},
- { .jtag_id = 0xb470, .die_rev = 0x0, .omap_id = 0x03310100, .type = 0x15100000},
- { .jtag_id = 0xb576, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x16100000},
- { .jtag_id = 0xb576, .die_rev = 0x2, .omap_id = 0x03320100, .type = 0x16110000},
- { .jtag_id = 0xb576, .die_rev = 0x3, .omap_id = 0x03320100, .type = 0x16100c00},
- { .jtag_id = 0xb576, .die_rev = 0x0, .omap_id = 0x03320200, .type = 0x16100d00},
- { .jtag_id = 0xb613, .die_rev = 0x0, .omap_id = 0x03320300, .type = 0x1610ef00},
- { .jtag_id = 0xb613, .die_rev = 0x0, .omap_id = 0x03320300, .type = 0x1610ef00},
- { .jtag_id = 0xb576, .die_rev = 0x1, .omap_id = 0x03320100, .type = 0x16110000},
- { .jtag_id = 0xb58c, .die_rev = 0x2, .omap_id = 0x03320200, .type = 0x16110b00},
- { .jtag_id = 0xb58c, .die_rev = 0x3, .omap_id = 0x03320200, .type = 0x16110c00},
- { .jtag_id = 0xb65f, .die_rev = 0x0, .omap_id = 0x03320400, .type = 0x16212300},
- { .jtag_id = 0xb65f, .die_rev = 0x1, .omap_id = 0x03320400, .type = 0x16212300},
- { .jtag_id = 0xb65f, .die_rev = 0x1, .omap_id = 0x03320500, .type = 0x16212300},
- { .jtag_id = 0xb5f7, .die_rev = 0x0, .omap_id = 0x03330000, .type = 0x17100000},
- { .jtag_id = 0xb5f7, .die_rev = 0x1, .omap_id = 0x03330100, .type = 0x17100000},
- { .jtag_id = 0xb5f7, .die_rev = 0x2, .omap_id = 0x03330100, .type = 0x17100000},
-};
-
-/*
- * Get OMAP type from PROD_ID.
- * 1710 has the PROD_ID in bits 15:00, not in 16:01 as documented in TRM.
- * 1510 PROD_ID is empty, and 1610 PROD_ID does not make sense.
- * Undocumented register in TEST BLOCK is used as fallback; This seems to
- * work on 1510, 1610 & 1710. The official way hopefully will work in future
- * processors.
- */
-static u16 omap_get_jtag_id(void)
-{
- u32 prod_id, omap_id;
-
- prod_id = omap_readl(OMAP_PRODUCTION_ID_1);
- omap_id = omap_readl(OMAP32_ID_1);
-
- /* Check for unusable OMAP_PRODUCTION_ID_1 on 1611B/5912 and 730 */
- if (((prod_id >> 20) == 0) || (prod_id == omap_id))
- prod_id = 0;
- else
- prod_id &= 0xffff;
-
- if (prod_id)
- return prod_id;
-
- /* Use OMAP32_ID_1 as fallback */
- prod_id = ((omap_id >> 12) & 0xffff);
-
- return prod_id;
-}
-
-/*
- * Get OMAP revision from DIE_REV.
- * Early 1710 processors may have broken OMAP_DIE_ID, it contains PROD_ID.
- * Undocumented register in the TEST BLOCK is used as fallback.
- * REVISIT: This does not seem to work on 1510
- */
-static u8 omap_get_die_rev(void)
-{
- u32 die_rev;
-
- die_rev = omap_readl(OMAP_DIE_ID_1);
-
- /* Check for broken OMAP_DIE_ID on early 1710 */
- if (((die_rev >> 12) & 0xffff) == omap_get_jtag_id())
- die_rev = 0;
-
- die_rev = (die_rev >> 17) & 0xf;
- if (die_rev)
- return die_rev;
-
- die_rev = (omap_readl(OMAP32_ID_1) >> 28) & 0xf;
-
- return die_rev;
-}
-
-static unsigned long dpll1(void)
-{
- unsigned short pll_ctl_val = omap_readw(DPLL_CTL_REG);
- unsigned long rate;
-
- rate = CONFIG_SYS_CLK_FREQ; /* Base xtal rate */
- if (pll_ctl_val & 0x10) {
- /* PLL enabled, apply multiplier and divisor */
- if (pll_ctl_val & 0xf80)
- rate *= (pll_ctl_val & 0xf80) >> 7;
- rate /= ((pll_ctl_val & 0x60) >> 5) + 1;
- } else {
- /* PLL disabled, apply bypass divisor */
- switch (pll_ctl_val & 0xc) {
- case 0:
- break;
- case 0x4:
- rate /= 2;
- break;
- default:
- rate /= 4;
- break;
- }
- }
-
- return rate;
-}
-
-static unsigned long armcore(void)
-{
- unsigned short arm_ckctl = omap_readw(ARM_CKCTL);
-
- return (dpll1() >> ((arm_ckctl & 0x0030) >> 4));
-}
-
-int print_cpuinfo (void)
-{
- int i;
- u16 jtag_id;
- u8 die_rev;
- u32 omap_id;
- u8 cpu_type;
- __maybe_unused u32 system_serial_high;
- __maybe_unused u32 system_serial_low;
- u32 system_rev = 0;
-
- jtag_id = omap_get_jtag_id();
- die_rev = omap_get_die_rev();
- omap_id = omap_readl(OMAP32_ID_0);
-
-#ifdef DEBUG
- printf("OMAP_DIE_ID_0: 0x%08x\n", omap_readl(OMAP_DIE_ID_0));
- printf("OMAP_DIE_ID_1: 0x%08x DIE_REV: %i\n",
- omap_readl(OMAP_DIE_ID_1),
- (omap_readl(OMAP_DIE_ID_1) >> 17) & 0xf);
- printf("OMAP_PRODUCTION_ID_0: 0x%08x\n", omap_readl(OMAP_PRODUCTION_ID_0));
- printf("OMAP_PRODUCTION_ID_1: 0x%08x JTAG_ID: 0x%04x\n",
- omap_readl(OMAP_PRODUCTION_ID_1),
- omap_readl(OMAP_PRODUCTION_ID_1) & 0xffff);
- printf("OMAP32_ID_0: 0x%08x\n", omap_readl(OMAP32_ID_0));
- printf("OMAP32_ID_1: 0x%08x\n", omap_readl(OMAP32_ID_1));
- printf("JTAG_ID: 0x%04x DIE_REV: %i\n", jtag_id, die_rev);
-#endif
-
- system_serial_high = omap_readl(OMAP_DIE_ID_0);
- system_serial_low = omap_readl(OMAP_DIE_ID_1);
-
- /* First check only the major version in a safe way */
- for (i = 0; i < ARRAY_SIZE(omap_ids); i++) {
- if (jtag_id == (omap_ids[i].jtag_id)) {
- system_rev = omap_ids[i].type;
- break;
- }
- }
-
- /* Check if we can find the die revision */
- for (i = 0; i < ARRAY_SIZE(omap_ids); i++) {
- if (jtag_id == omap_ids[i].jtag_id && die_rev == omap_ids[i].die_rev) {
- system_rev = omap_ids[i].type;
- break;
- }
- }
-
- /* Finally check also the omap_id */
- for (i = 0; i < ARRAY_SIZE(omap_ids); i++) {
- if (jtag_id == omap_ids[i].jtag_id
- && die_rev == omap_ids[i].die_rev
- && omap_id == omap_ids[i].omap_id) {
- system_rev = omap_ids[i].type;
- break;
- }
- }
-
- /* Add the cpu class info (7xx, 15xx, 16xx, 24xx) */
- cpu_type = system_rev >> 24;
-
- switch (cpu_type) {
- case 0x07:
- system_rev |= 0x07;
- break;
- case 0x03:
- case 0x15:
- system_rev |= 0x15;
- break;
- case 0x16:
- case 0x17:
- system_rev |= 0x16;
- break;
- case 0x24:
- system_rev |= 0x24;
- break;
- default:
- printf("Unknown OMAP cpu type: 0x%02x\n", cpu_type);
- }
-
- printf("CPU: OMAP%04x", system_rev >> 16);
- if ((system_rev >> 8) & 0xff)
- printf("%x", (system_rev >> 8) & 0xff);
-#ifdef DEBUG
- printf(" revision %i handled as %02xxx id: %08x%08x",
- die_rev, system_rev & 0xff, system_serial_low, system_serial_high);
-#endif
- printf(" at %ld.%01ld MHz (DPLL1=%ld.%01ld MHz)\n",
- armcore() / 1000000, (armcore() / 100000) % 10,
- dpll1() / 1000000, (dpll1() / 100000) % 10);
-
- return 0;
-}
-
-#endif /* #if defined(CONFIG_OMAP) */
+++ /dev/null
-/*
- * armboot - Startup Code for ARM926EJS CPU-core
- *
- * Copyright (c) 2003 Texas Instruments
- *
- * ----- Adapted for OMAP1610 OMAP730 from ARM925t code ------
- *
- * Copyright (c) 2001 Marius Gröger <mag@sysgo.de>
- * Copyright (c) 2002 Alex Züpke <azu@sysgo.de>
- * Copyright (c) 2002 Gary Jennejohn <garyj@denx.de>
- * Copyright (c) 2003 Richard Woodruff <r-woodruff2@ti.com>
- * Copyright (c) 2003 Kshitij <kshitij@ti.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
- .align 5
-.globl reset_cpu
-reset_cpu:
- ldr r1, rstctl1 /* get clkm1 reset ctl */
- mov r3, #0x0
- strh r3, [r1] /* clear it */
- mov r3, #0x8
- strh r3, [r1] /* force dsp+arm reset */
-_loop_forever:
- b _loop_forever
-
-rstctl1:
- .word 0xfffece10
+++ /dev/null
-/*
- * (C) Copyright 2003
- * Texas Instruments <www.ti.com>
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Alex Zuepke <azu@sysgo.de>
- *
- * (C) Copyright 2002-2004
- * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
- *
- * (C) Copyright 2004
- * Philippe Robin, ARM Ltd. <philippe.robin@arm.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-
-#define TIMER_CLOCK (CONFIG_SYS_CLK_FREQ / (2 << CONFIG_SYS_PTV))
-#define TIMER_LOAD_VAL 0xffffffff
-
-/* macro to read the 32 bit timer */
-#define READ_TIMER readl(CONFIG_SYS_TIMERBASE+8) \
- / (TIMER_CLOCK / CONFIG_SYS_HZ)
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define timestamp gd->arch.tbl
-#define lastdec gd->arch.lastinc
-
-int timer_init (void)
-{
- int32_t val;
-
- /* Start the decrementer ticking down from 0xffffffff */
- *((int32_t *) (CONFIG_SYS_TIMERBASE + LOAD_TIM)) = TIMER_LOAD_VAL;
- val = MPUTIM_ST | MPUTIM_AR | MPUTIM_CLOCK_ENABLE | (CONFIG_SYS_PTV << MPUTIM_PTV_BIT);
- *((int32_t *) (CONFIG_SYS_TIMERBASE + CNTL_TIMER)) = val;
-
- /* init the timestamp and lastdec value */
- reset_timer_masked();
-
- return 0;
-}
-
-/*
- * timer without interrupts
- */
-ulong get_timer (ulong base)
-{
- return get_timer_masked () - base;
-}
-
-/* delay x useconds AND preserve advance timestamp value */
-void __udelay (unsigned long usec)
-{
- ulong tmo, tmp;
-
- if(usec >= 1000){ /* if "big" number, spread normalization to seconds */
- tmo = usec / 1000; /* start to normalize for usec to ticks per sec */
- tmo *= CONFIG_SYS_HZ; /* find number of "ticks" to wait to achieve target */
- tmo /= 1000; /* finish normalize. */
- }else{ /* else small number, don't kill it prior to HZ multiply */
- tmo = usec * CONFIG_SYS_HZ;
- tmo /= (1000*1000);
- }
-
- tmp = get_timer (0); /* get current timestamp */
- if( (tmo + tmp + 1) < tmp ) /* if setting this fordward will roll time stamp */
- reset_timer_masked (); /* reset "advancing" timestamp to 0, set lastdec value */
- else
- tmo += tmp; /* else, set advancing stamp wake up time */
-
- while (get_timer_masked () < tmo)/* loop till event */
- /*NOP*/;
-}
-
-void reset_timer_masked (void)
-{
- /* reset time */
- lastdec = READ_TIMER; /* capure current decrementer value time */
- timestamp = 0; /* start "advancing" time stamp from 0 */
-}
-
-ulong get_timer_masked (void)
-{
- ulong now = READ_TIMER; /* current tick value */
-
- if (lastdec >= now) { /* normal mode (non roll) */
- /* normal mode */
- timestamp += lastdec - now; /* move stamp fordward with absoulte diff ticks */
- } else { /* we have overflow of the count down timer */
- /* nts = ts + ld + (TLV - now)
- * ts=old stamp, ld=time that passed before passing through -1
- * (TLV-now) amount of time after passing though -1
- * nts = new "advancing time stamp"...it could also roll and cause problems.
- */
- timestamp += lastdec + (TIMER_LOAD_VAL / (TIMER_CLOCK /
- CONFIG_SYS_HZ)) - now;
- }
- lastdec = now;
-
- return timestamp;
-}
-
-/* waits specified delay value and resets timestamp */
-void udelay_masked (unsigned long usec)
-{
- ulong tmo;
- ulong endtime;
- signed long diff;
-
- if (usec >= 1000) { /* if "big" number, spread normalization to seconds */
- tmo = usec / 1000; /* start to normalize for usec to ticks per sec */
- tmo *= CONFIG_SYS_HZ; /* find number of "ticks" to wait to achieve target */
- tmo /= 1000; /* finish normalize. */
- } else { /* else small number, don't kill it prior to HZ multiply */
- tmo = usec * CONFIG_SYS_HZ;
- tmo /= (1000*1000);
- }
-
- endtime = get_timer_masked () + tmo;
-
- do {
- ulong now = get_timer_masked ();
- diff = endtime - now;
- } while (diff >= 0);
-}
-
-/*
- * This function is derived from PowerPC code (read timebase as long long).
- * On ARM it just returns the timer value.
- */
-unsigned long long get_ticks(void)
-{
- return get_timer(0);
-}
-
-/*
- * This function is derived from PowerPC code (timebase clock frequency).
- * On ARM it returns the number of timer ticks per second.
- */
-ulong get_tbclk (void)
-{
- return CONFIG_SYS_HZ;
-}
0:
/*
- * Enalbe SMPEN bit for coherency.
+ * Enable SMPEN bit for coherency.
* This register is not architectural but at the moment
* this bit should be set for A53/A57/A72.
*/
#ifdef CONFIG_ARMV8_SET_SMPEN
- mrs x0, S3_1_c15_c2_1 /* cpuactlr_el1 */
+ mrs x0, S3_1_c15_c2_1 /* cpuectlr_el1 */
orr x0, x0, #0x40
msr S3_1_c15_c2_1, x0
#endif
#define MV_UART_CONSOLE_BASE ARMD1_UART1_BASE
#define CONFIG_SYS_NS16550_IER (1 << 6) /* Bit 6 in UART_IER register
represents UART Unit Enable */
-/*
- * I2C definition
- */
-#ifdef CONFIG_CMD_I2C
-#define CONFIG_I2C_MV 1
-#define CONFIG_MV_I2C_NUM 2
-#define CONFIG_I2C_MULTI_BUS 1
-#define CONFIG_MV_I2C_REG {0xd4011000, 0xd4025000}
-#define CONFIG_HARD_I2C 1
-#define CONFIG_SYS_I2C_SPEED 0
-#define CONFIG_SYS_I2C_SLAVE 0xfe
-#endif
#endif /* _ARMD1_CONFIG_H */
#ifdef CONFIG_MXC_OCOTP
void enable_ocotp_clk(unsigned char enable);
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
void enable_usboh3_clk(unsigned char enable);
#endif
void init_clk_usdhc(u32 index);
#define DPLL_NO_LOCK 0
#define DPLL_LOCK 1
-/*
- * MAX value for PRM_RSTTIME[9:0]RSTTIME1 stored is 0x3ff.
- * 0x3ff is in the no of FUNC_32K_CLK cycles. Converting cycles
- * into microsec and passing the value.
- */
-#define CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC 31219
-
#if defined(CONFIG_DRA7XX)
#define V_OSCK 20000000 /* Clock output from T2 */
#else
u32 lcd0_ch0_clk_cfg; /* 0x118 LCD0 CH0 module clock */
u32 lcd1_ch0_clk_cfg; /* 0x11c LCD1 CH0 module clock */
#endif
- u32 reserved14[3];
+ u32 tve_clk_cfg; /* 0x120 H3/H5 TVE module clock */
+ u32 reserved14[2];
u32 lcd0_ch1_clk_cfg; /* 0x12c LCD0 CH1 module clock */
u32 lcd1_ch1_clk_cfg; /* 0x130 LCD1 CH1 module clock */
u32 csi0_clk_cfg; /* 0x134 CSI0 module clock */
#define AHB_GATE_OFFSET_DE_BE0 12
#define AHB_GATE_OFFSET_DE 12
#define AHB_GATE_OFFSET_HDMI 11
+#define AHB_GATE_OFFSET_TVE 9
#ifndef CONFIG_SUNXI_DE2
#define AHB_GATE_OFFSET_LCD1 5
#define AHB_GATE_OFFSET_LCD0 4
#define CCM_HDMI_SLOW_CTRL_DDC_GATE (1 << 31)
+#define CCM_TVE_CTRL_GATE (0x1 << 31)
+#define CCM_TVE_CTRL_M(n) ((((n) - 1) & 0xf) << 0)
+
#if defined(CONFIG_MACH_SUN50I)
#define MBUS_CLK_DEFAULT 0x81000002 /* PLL6x2 / 3 */
#elif defined(CONFIG_MACH_SUN8I)
#define AHB_RESET_OFFSET_DE 12
#define AHB_RESET_OFFSET_HDMI 11
#define AHB_RESET_OFFSET_HDMI2 10
+#define AHB_RESET_OFFSET_TVE 9
#ifndef CONFIG_SUNXI_DE2
#define AHB_RESET_OFFSET_LCD1 5
#define AHB_RESET_OFFSET_LCD0 4
#endif
};
-/*
- * This is based on the A10s User Manual, and the A10s only supports
- * composite video and not vga like the A10 / A20 does, still other
- * than the removed vga out capability the tvencoder seems to be the same.
- * "unknown#" registers are registers which are used in the A10 kernel code,
- * but not documented in the A10s User Manual.
- */
-struct sunxi_tve_reg {
- u32 gctrl; /* 0x000 */
- u32 cfg0; /* 0x004 */
- u32 dac_cfg0; /* 0x008 */
- u32 filter; /* 0x00c */
- u32 chroma_freq; /* 0x010 */
- u32 porch_num; /* 0x014 */
- u32 unknown0; /* 0x018 */
- u32 line_num; /* 0x01c */
- u32 blank_black_level; /* 0x020 */
- u32 unknown1; /* 0x024, seems to be 1 byte per dac */
- u8 res0[0x08]; /* 0x028 */
- u32 auto_detect_en; /* 0x030 */
- u32 auto_detect_int_status; /* 0x034 */
- u32 auto_detect_status; /* 0x038 */
- u32 auto_detect_debounce; /* 0x03c */
- u32 csc_reg0; /* 0x040 */
- u32 csc_reg1; /* 0x044 */
- u32 csc_reg2; /* 0x048 */
- u32 csc_reg3; /* 0x04c */
- u8 res1[0xb0]; /* 0x050 */
- u32 color_burst; /* 0x100 */
- u32 vsync_num; /* 0x104 */
- u32 notch_freq; /* 0x108 */
- u32 cbr_level; /* 0x10c */
- u32 burst_phase; /* 0x110 */
- u32 burst_width; /* 0x114 */
- u32 unknown2; /* 0x118 */
- u32 sync_vbi_level; /* 0x11c */
- u32 white_level; /* 0x120 */
- u32 active_num; /* 0x124 */
- u32 chroma_bw_gain; /* 0x128 */
- u32 notch_width; /* 0x12c */
- u32 resync_num; /* 0x130 */
- u32 slave_para; /* 0x134 */
- u32 cfg1; /* 0x138 */
- u32 cfg2; /* 0x13c */
-};
-
/*
* DE-FE register constants.
*/
#define SUNXI_HMDI_DDC_LINE_CTRL_SCL_ENABLE (1 << 8)
#define SUNXI_HMDI_DDC_LINE_CTRL_SDA_ENABLE (1 << 9)
-/*
- * TVE register constants.
- */
-#define SUNXI_TVE_GCTRL_ENABLE (1 << 0)
-/*
- * Select input 0 to disable dac, 1 - 4 to feed dac from tve0, 5 - 8 to feed
- * dac from tve1. When using tve1 the mux value must be written to both tve0's
- * and tve1's gctrl reg.
- */
-#define SUNXI_TVE_GCTRL_DAC_INPUT_MASK(dac) (0xf << (((dac) + 1) * 4))
-#define SUNXI_TVE_GCTRL_DAC_INPUT(dac, sel) ((sel) << (((dac) + 1) * 4))
-#define SUNXI_TVE_CFG0_VGA 0x20000000
-#define SUNXI_TVE_CFG0_PAL 0x07030001
-#define SUNXI_TVE_CFG0_NTSC 0x07030000
-#define SUNXI_TVE_DAC_CFG0_VGA 0x403e1ac7
-#ifdef CONFIG_MACH_SUN5I
-#define SUNXI_TVE_DAC_CFG0_COMPOSITE 0x433f0009
-#else
-#define SUNXI_TVE_DAC_CFG0_COMPOSITE 0x403f0008
-#endif
-#define SUNXI_TVE_FILTER_COMPOSITE 0x00000120
-#define SUNXI_TVE_CHROMA_FREQ_PAL_M 0x21e6efe3
-#define SUNXI_TVE_CHROMA_FREQ_PAL_NC 0x21f69446
-#define SUNXI_TVE_PORCH_NUM_PAL 0x008a0018
-#define SUNXI_TVE_PORCH_NUM_NTSC 0x00760020
-#define SUNXI_TVE_LINE_NUM_PAL 0x00160271
-#define SUNXI_TVE_LINE_NUM_NTSC 0x0016020d
-#define SUNXI_TVE_BLANK_BLACK_LEVEL_PAL 0x00fc00fc
-#define SUNXI_TVE_BLANK_BLACK_LEVEL_NTSC 0x00f0011a
-#define SUNXI_TVE_UNKNOWN1_VGA 0x00000000
-#define SUNXI_TVE_UNKNOWN1_COMPOSITE 0x18181818
-#define SUNXI_TVE_AUTO_DETECT_EN_DET_EN(dac) (1 << ((dac) + 0))
-#define SUNXI_TVE_AUTO_DETECT_EN_INT_EN(dac) (1 << ((dac) + 16))
-#define SUNXI_TVE_AUTO_DETECT_INT_STATUS(dac) (1 << ((dac) + 0))
-#define SUNXI_TVE_AUTO_DETECT_STATUS_SHIFT(dac) ((dac) * 8)
-#define SUNXI_TVE_AUTO_DETECT_STATUS_MASK(dac) (3 << ((dac) * 8))
-#define SUNXI_TVE_AUTO_DETECT_STATUS_NONE 0
-#define SUNXI_TVE_AUTO_DETECT_STATUS_CONNECTED 1
-#define SUNXI_TVE_AUTO_DETECT_STATUS_SHORT_GND 3
-#define SUNXI_TVE_AUTO_DETECT_DEBOUNCE_SHIFT(d) ((d) * 8)
-#define SUNXI_TVE_AUTO_DETECT_DEBOUNCE_MASK(d) (0xf << ((d) * 8))
-#define SUNXI_TVE_CSC_REG0_ENABLE (1 << 31)
-#define SUNXI_TVE_CSC_REG0 0x08440832
-#define SUNXI_TVE_CSC_REG1 0x3b6dace1
-#define SUNXI_TVE_CSC_REG2 0x0e1d13dc
-#define SUNXI_TVE_CSC_REG3 0x00108080
-#define SUNXI_TVE_COLOR_BURST_PAL_M 0x00000000
-#define SUNXI_TVE_CBR_LEVEL_PAL 0x00002828
-#define SUNXI_TVE_CBR_LEVEL_NTSC 0x0000004f
-#define SUNXI_TVE_BURST_PHASE_NTSC 0x00000000
-#define SUNXI_TVE_BURST_WIDTH_COMPOSITE 0x0016447e
-#define SUNXI_TVE_UNKNOWN2_PAL 0x0000e0e0
-#define SUNXI_TVE_UNKNOWN2_NTSC 0x0000a0a0
-#define SUNXI_TVE_SYNC_VBI_LEVEL_NTSC 0x001000f0
-#define SUNXI_TVE_ACTIVE_NUM_COMPOSITE 0x000005a0
-#define SUNXI_TVE_CHROMA_BW_GAIN_COMP 0x00000002
-#define SUNXI_TVE_NOTCH_WIDTH_COMPOSITE 0x00000101
-#define SUNXI_TVE_RESYNC_NUM_PAL 0x800d000c
-#define SUNXI_TVE_RESYNC_NUM_NTSC 0x000e000c
-#define SUNXI_TVE_SLAVE_PARA_COMPOSITE 0x00000000
-
int sunxi_simplefb_setup(void *blob);
#endif /* _SUNXI_DISPLAY_H */
--- /dev/null
+/*
+ * Sunxi TV encoder register and constant defines
+ *
+ * (C) Copyright 2014 Hans de Goede <hdegoede@redhat.com>
+ * (C) Copyright 2017 Jernej Skrabec <jernej.skrabec@siol.net>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _TVE_H
+#define _TVE_H
+
+enum tve_mode {
+ tve_mode_vga,
+ tve_mode_composite_pal,
+ tve_mode_composite_ntsc,
+ tve_mode_composite_pal_m,
+ tve_mode_composite_pal_nc,
+};
+
+/*
+ * This is based on the A10s User Manual, and the A10s only supports
+ * composite video and not vga like the A10 / A20 does, still other
+ * than the removed vga out capability the tvencoder seems to be the same.
+ * "unknown#" registers are registers which are used in the A10 kernel code,
+ * but not documented in the A10s User Manual.
+ */
+struct sunxi_tve_reg {
+ u32 gctrl; /* 0x000 */
+ u32 cfg0; /* 0x004 */
+ u32 dac_cfg0; /* 0x008 */
+ u32 filter; /* 0x00c */
+ u32 chroma_freq; /* 0x010 */
+ u32 porch_num; /* 0x014 */
+ u32 unknown0; /* 0x018 */
+ u32 line_num; /* 0x01c */
+ u32 blank_black_level; /* 0x020 */
+ u32 unknown1; /* 0x024, seems to be 1 byte per dac */
+ u8 res0[0x08]; /* 0x028 */
+ u32 auto_detect_en; /* 0x030 */
+ u32 auto_detect_int_status; /* 0x034 */
+ u32 auto_detect_status; /* 0x038 */
+ u32 auto_detect_debounce; /* 0x03c */
+ u32 csc_reg0; /* 0x040 */
+ u32 csc_reg1; /* 0x044 */
+ u32 csc_reg2; /* 0x048 */
+ u32 csc_reg3; /* 0x04c */
+ u8 res1[0xb0]; /* 0x050 */
+ u32 color_burst; /* 0x100 */
+ u32 vsync_num; /* 0x104 */
+ u32 notch_freq; /* 0x108 */
+ u32 cbr_level; /* 0x10c */
+ u32 burst_phase; /* 0x110 */
+ u32 burst_width; /* 0x114 */
+ u32 unknown2; /* 0x118 */
+ u32 sync_vbi_level; /* 0x11c */
+ u32 white_level; /* 0x120 */
+ u32 active_num; /* 0x124 */
+ u32 chroma_bw_gain; /* 0x128 */
+ u32 notch_width; /* 0x12c */
+ u32 resync_num; /* 0x130 */
+ u32 slave_para; /* 0x134 */
+ u32 cfg1; /* 0x138 */
+ u32 cfg2; /* 0x13c */
+};
+
+/*
+ * TVE register constants.
+ */
+#define SUNXI_TVE_GCTRL_ENABLE (1 << 0)
+/*
+ * Select input 0 to disable dac, 1 - 4 to feed dac from tve0, 5 - 8 to feed
+ * dac from tve1. When using tve1 the mux value must be written to both tve0's
+ * and tve1's gctrl reg.
+ */
+#define SUNXI_TVE_GCTRL_DAC_INPUT_MASK(dac) (0xf << (((dac) + 1) * 4))
+#define SUNXI_TVE_GCTRL_DAC_INPUT(dac, sel) ((sel) << (((dac) + 1) * 4))
+#define SUNXI_TVE_CFG0_VGA 0x20000000
+#define SUNXI_TVE_CFG0_PAL 0x07030001
+#define SUNXI_TVE_CFG0_NTSC 0x07030000
+#define SUNXI_TVE_DAC_CFG0_VGA 0x403e1ac7
+#ifdef CONFIG_MACH_SUN5I
+#define SUNXI_TVE_DAC_CFG0_COMPOSITE 0x433f0009
+#else
+#define SUNXI_TVE_DAC_CFG0_COMPOSITE 0x403f0008
+#endif
+#define SUNXI_TVE_FILTER_COMPOSITE 0x00000120
+#define SUNXI_TVE_CHROMA_FREQ_PAL_M 0x21e6efe3
+#define SUNXI_TVE_CHROMA_FREQ_PAL_NC 0x21f69446
+#define SUNXI_TVE_PORCH_NUM_PAL 0x008a0018
+#define SUNXI_TVE_PORCH_NUM_NTSC 0x00760020
+#define SUNXI_TVE_LINE_NUM_PAL 0x00160271
+#define SUNXI_TVE_LINE_NUM_NTSC 0x0016020d
+#define SUNXI_TVE_BLANK_BLACK_LEVEL_PAL 0x00fc00fc
+#define SUNXI_TVE_BLANK_BLACK_LEVEL_NTSC 0x00f0011a
+#define SUNXI_TVE_UNKNOWN1_VGA 0x00000000
+#define SUNXI_TVE_UNKNOWN1_COMPOSITE 0x18181818
+#define SUNXI_TVE_AUTO_DETECT_EN_DET_EN(dac) (1 << ((dac) + 0))
+#define SUNXI_TVE_AUTO_DETECT_EN_INT_EN(dac) (1 << ((dac) + 16))
+#define SUNXI_TVE_AUTO_DETECT_INT_STATUS(dac) (1 << ((dac) + 0))
+#define SUNXI_TVE_AUTO_DETECT_STATUS_SHIFT(dac) ((dac) * 8)
+#define SUNXI_TVE_AUTO_DETECT_STATUS_MASK(dac) (3 << ((dac) * 8))
+#define SUNXI_TVE_AUTO_DETECT_STATUS_NONE 0
+#define SUNXI_TVE_AUTO_DETECT_STATUS_CONNECTED 1
+#define SUNXI_TVE_AUTO_DETECT_STATUS_SHORT_GND 3
+#define SUNXI_TVE_AUTO_DETECT_DEBOUNCE_SHIFT(d) ((d) * 8)
+#define SUNXI_TVE_AUTO_DETECT_DEBOUNCE_MASK(d) (0xf << ((d) * 8))
+#define SUNXI_TVE_CSC_REG0_ENABLE (1 << 31)
+#define SUNXI_TVE_CSC_REG0 0x08440832
+#define SUNXI_TVE_CSC_REG1 0x3b6dace1
+#define SUNXI_TVE_CSC_REG2 0x0e1d13dc
+#define SUNXI_TVE_CSC_REG3 0x00108080
+#define SUNXI_TVE_COLOR_BURST_PAL_M 0x00000000
+#define SUNXI_TVE_CBR_LEVEL_PAL 0x00002828
+#define SUNXI_TVE_CBR_LEVEL_NTSC 0x0000004f
+#define SUNXI_TVE_BURST_PHASE_NTSC 0x00000000
+#define SUNXI_TVE_BURST_WIDTH_COMPOSITE 0x0016447e
+#define SUNXI_TVE_UNKNOWN2_PAL 0x0000e0e0
+#define SUNXI_TVE_UNKNOWN2_NTSC 0x0000a0a0
+#define SUNXI_TVE_SYNC_VBI_LEVEL_NTSC 0x001000f0
+#define SUNXI_TVE_ACTIVE_NUM_COMPOSITE 0x000005a0
+#define SUNXI_TVE_CHROMA_BW_GAIN_COMP 0x00000002
+#define SUNXI_TVE_NOTCH_WIDTH_COMPOSITE 0x00000101
+#define SUNXI_TVE_RESYNC_NUM_PAL 0x800d000c
+#define SUNXI_TVE_RESYNC_NUM_NTSC 0x000e000c
+#define SUNXI_TVE_SLAVE_PARA_COMPOSITE 0x00000000
+
+void tvencoder_mode_set(struct sunxi_tve_reg * const tve, enum tve_mode mode);
+void tvencoder_enable(struct sunxi_tve_reg * const tve);
+
+#endif /* _TVE_H */
#ifndef _ASM_SPL_H_
#define _ASM_SPL_H_
-#if defined(CONFIG_OMAP) \
+#if defined(CONFIG_ARCH_OMAP2PLUS) \
|| defined(CONFIG_EXYNOS4) || defined(CONFIG_EXYNOS5) \
|| defined(CONFIG_EXYNOS4210)
/* Platform-specific defines */
}
#endif
-#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI)
+#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI_HCD)
void at91_uhp_hw_init(void)
{
/* Enable VBus on UHP ports */
* USB/EHCI
*/
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI_MARVELL
#define CONFIG_EHCI_IS_TDI
#endif /* CONFIG_CMD_USB */
if OMAP34XX
+# We only enable the clocks for the GPIO banks that a given board requies.
+config OMAP3_GPIO_2
+ bool
+
+config OMAP3_GPIO_3
+ bool
+
+config OMAP3_GPIO_4
+ bool
+
+config OMAP3_GPIO_5
+ bool
+
+config OMAP3_GPIO_6
+ bool
+
choice
prompt "OMAP3 board select"
optional
config TARGET_MT_VENTOUX
bool "TeeJet Mt.Ventoux"
+ select OMAP3_GPIO_4
+ select OMAP3_GPIO_5 if USB_EHCI_HCD
config TARGET_OMAP3_BEAGLE
bool "TI OMAP3 BeagleBoard"
select DM
select DM_SERIAL
select DM_GPIO
+ select OMAP3_GPIO_5
+ select OMAP3_GPIO_6
config TARGET_CM_T35
bool "CompuLab CM-T3530 and CM-T3730 boards"
+ select OMAP3_GPIO_2
+ select OMAP3_GPIO_5
+ select OMAP3_GPIO_6 if LED_STATUS
config TARGET_CM_T3517
bool "CompuLab CM-T3517 boards"
+ select OMAP3_GPIO_2
+ select OMAP3_GPIO_5
+ select OMAP3_GPIO_6 if LED_STATUS
config TARGET_DEVKIT8000
bool "TimLL OMAP3 Devkit8000"
select DM
select DM_SERIAL
select DM_GPIO
+ select OMAP3_GPIO_3
+ select OMAP3_GPIO_5
+ select OMAP3_GPIO_6
config TARGET_OMAP3_OVERO
bool "OMAP35xx Gumstix Overo"
select DM
select DM_SERIAL
select DM_GPIO
+ select OMAP3_GPIO_2
+ select OMAP3_GPIO_3
+ select OMAP3_GPIO_4
+ select OMAP3_GPIO_5
+ select OMAP3_GPIO_6
config TARGET_OMAP3_ZOOM1
bool "TI Zoom1"
config TARGET_OMAP3_PANDORA
bool "OMAP3 Pandora"
+ select OMAP3_GPIO_4
+ select OMAP3_GPIO_6
config TARGET_ECO5PK
bool "ECO5PK"
+ select OMAP3_GPIO_5 if USB_EHCI_HCD
config TARGET_TRICORDER
bool "Tricorder"
+ select OMAP3_GPIO_2
config TARGET_MCX
bool "MCX"
select BOARD_LATE_INIT
+ select OMAP3_GPIO_2 if USB_EHCI_HCD
+ select OMAP3_GPIO_5 if USB_EHCI_HCD
config TARGET_OMAP3_LOGIC
bool "OMAP3 Logic"
select DM
select DM_SERIAL
select DM_GPIO
+ select OMAP3_GPIO_4
+ select OMAP3_GPIO_6
config TARGET_NOKIA_RX51
bool "Nokia RX51"
config TARGET_TAO3530
bool "TAO3530"
+ select OMAP3_GPIO_2
+ select OMAP3_GPIO_3
+ select OMAP3_GPIO_4
+ select OMAP3_GPIO_5
+ select OMAP3_GPIO_6
config TARGET_TWISTER
bool "Twister"
+ select OMAP3_GPIO_2
+ select OMAP3_GPIO_5 if USB_EHCI_HCD
config TARGET_OMAP3_CAIRO
bool "QUIPOS CAIRO"
select DM
select DM_SERIAL
select DM_GPIO
+ select OMAP3_GPIO_2
+ select OMAP3_GPIO_3
+ select OMAP3_GPIO_4
+ select OMAP3_GPIO_5
+ select OMAP3_GPIO_6
endchoice
using hardware memory firewalls. This value must be smaller than the
TI_SECURE_EMIF_TOTAL_REGION_SIZE value.
+config OMAP_PLATFORM_RESET_TIME_MAX_USEC
+ int "Something"
+ range 0 31219
+ default 31219
+ help
+ Most OMAPs' provide a way to specify the time for which the reset
+ should be held low while the voltages and Oscillator outputs
+ stabilize.
+ This time is mostly board and PMIC dependent. Hence the boards are
+ expected to specify a pre-computed time using the above option.
+ This value can be computed using a summation of the below 3
+ parameters
+ 1: Time taken by the Osciallator to stop and restart
+ 2: PMIC OTP time
+ 3: Voltage ramp time, which can be derived using the PMIC slew rate
+ and value of voltage ramp needed.
+
if TARGET_DRA7XX_EVM || TARGET_AM57XX_EVM
menu "Voltage Domain OPP selections"
{
u32 rst_time, rst_val;
-#ifndef CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC
- rst_time = CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC;
-#else
- rst_time = CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC;
-#endif
- rst_time = usec_to_32k(rst_time) << RSTTIME1_SHIFT;
+ /*
+ * MAX value for PRM_RSTTIME[9:0]RSTTIME1 stored is 0x3ff.
+ * 0x3ff is in the no of FUNC_32K_CLK cycles. Converting cycles
+ * into microsec and passing the value.
+ */
+ rst_time = usec_to_32k(CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC)
+ << RSTTIME1_SHIFT;
if (rst_time > RSTTIME1_MASK)
rst_time = RSTTIME1_MASK;
#include <asm/arch/sys_proto.h>
#include <asm/arch/clock.h>
-/*
- * Define Master code if there are multiple masters on the I2C_SR bus.
- * Normally not required
- */
-#ifndef CONFIG_OMAP_VC_I2C_HS_MCODE
-#define CONFIG_OMAP_VC_I2C_HS_MCODE 0x0
-#endif
-
/* Register defines and masks for VC IP Block */
/* PRM_VC_CFG_I2C_MODE */
#define PRM_VC_CFG_I2C_MODE_DFILTEREN_BIT (0x1 << 6)
(cycles_low << PRM_VC_CFG_I2C_CLK_SCLL_SHIFT);
writel(val, (*prcm)->prm_vc_cfg_i2c_clk);
- val = CONFIG_OMAP_VC_I2C_HS_MCODE <<
- PRM_VC_CFG_I2C_MODE_HSMCODE_SHIFT;
+ /*
+ * Master code if there are multiple masters on the I2C_SR bus.
+ */
+ val = 0x0 << PRM_VC_CFG_I2C_MODE_HSMCODE_SHIFT;
/* No HS mode for now */
val &= ~PRM_VC_CFG_I2C_MODE_HSMODEEN_BIT;
writel(val, (*prcm)->prm_vc_cfg_i2c_mode);
/* TODO: use "mmc-pwrseq-emmc" */
writel(1, SDCTRL_EMMC_HW_RESET);
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
{
/* FIXME: the current clk driver can not handle parents */
u32 tmp;
#ifdef CONFIG_UNIPHIER_ETH
tmp |= SC_CLKCTRL_CEN_ETHER;
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
tmp |= SC_CLKCTRL_CEN_MIO | SC_CLKCTRL_CEN_STDMAC;
#endif
#ifdef CONFIG_NAND_DENALI
#ifdef CONFIG_UNIPHIER_ETH
tmp |= SC_CLKCTRL_CEN_ETHER;
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
tmp |= SC_CLKCTRL_CEN_MIO | SC_CLKCTRL_CEN_STDMAC;
#endif
#ifdef CONFIG_NAND_DENALI
select CREATE_ARCH_SYMLINK
select SYS_FSL_DDR
select SYS_FSL_DDR_BE
+ imply USB_EHCI_HCD if USB
config MPC86xx
bool "MPC86xx"
obj-y += traps.o
obj-y += cpu_init.o
obj-y += fixed_sdram.o
-obj-y += i2c.o
obj-y += interrupts.o
obj-y += iopin.o
obj-y += serial.o
+++ /dev/null
-/*
- * (C) Copyright 2003 - 2009
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- *
- * Based on the MPC5xxx code.
- */
-
-#include <common.h>
-#include <asm/io.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_HARD_I2C
-
-#include <i2c.h>
-
-/* by default set I2C bus 0 active */
-static unsigned int bus_num __attribute__ ((section (".data"))) = 0;
-
-#define I2C_TIMEOUT 100
-#define I2C_RETRIES 3
-
-struct mpc512x_i2c_tap {
- int scl2tap;
- int tap2tap;
-};
-
-static int mpc_reg_in(volatile u32 *reg);
-static void mpc_reg_out(volatile u32 *reg, int val, int mask);
-static int wait_for_bb(void);
-static int wait_for_pin(int *status);
-static int do_address(uchar chip, char rdwr_flag);
-static int send_bytes(uchar chip, char *buf, int len);
-static int receive_bytes(uchar chip, char *buf, int len);
-static int mpc_get_fdr(int);
-
-static int mpc_reg_in (volatile u32 *reg)
-{
- int ret = in_be32(reg) >> 24;
-
- return ret;
-}
-
-static void mpc_reg_out (volatile u32 *reg, int val, int mask)
-{
- if (!mask) {
- out_be32(reg, val << 24);
- } else {
- clrsetbits_be32(reg, mask << 24, (val & mask) << 24);
- }
-}
-
-static int wait_for_bb (void)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- int timeout = I2C_TIMEOUT;
- int status;
-
- status = mpc_reg_in (®s->msr);
-
- while (timeout-- && (status & I2C_BB)) {
- mpc_reg_out (®s->mcr, I2C_STA, I2C_STA);
- (void)mpc_reg_in(®s->mdr);
- mpc_reg_out (®s->mcr, 0, I2C_STA);
- mpc_reg_out (®s->mcr, 0, 0);
- mpc_reg_out (®s->mcr, I2C_EN, 0);
-
- udelay (1000);
- status = mpc_reg_in (®s->msr);
- }
-
- return (status & I2C_BB);
-}
-
-static int wait_for_pin (int *status)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- int timeout = I2C_TIMEOUT;
-
- *status = mpc_reg_in (®s->msr);
-
- while (timeout-- && !(*status & I2C_IF)) {
- udelay (1000);
- *status = mpc_reg_in (®s->msr);
- }
-
- if (!(*status & I2C_IF)) {
- return -1;
- }
-
- mpc_reg_out (®s->msr, 0, I2C_IF);
-
- return 0;
-}
-
-static int do_address (uchar chip, char rdwr_flag)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- int status;
-
- chip <<= 1;
-
- if (rdwr_flag) {
- chip |= 1;
- }
-
- mpc_reg_out (®s->mcr, I2C_TX, I2C_TX);
- mpc_reg_out (®s->mdr, chip, 0);
-
- if (wait_for_pin (&status)) {
- return -2;
- }
-
- if (status & I2C_RXAK) {
- return -3;
- }
-
- return 0;
-}
-
-static int send_bytes (uchar chip, char *buf, int len)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- int wrcount;
- int status;
-
- for (wrcount = 0; wrcount < len; ++wrcount) {
-
- mpc_reg_out (®s->mdr, buf[wrcount], 0);
-
- if (wait_for_pin (&status)) {
- break;
- }
-
- if (status & I2C_RXAK) {
- break;
- }
-
- }
-
- return !(wrcount == len);
-}
-
-static int receive_bytes (uchar chip, char *buf, int len)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- int dummy = 1;
- int rdcount = 0;
- int status;
- int i;
-
- mpc_reg_out (®s->mcr, 0, I2C_TX);
-
- for (i = 0; i < len; ++i) {
- buf[rdcount] = mpc_reg_in (®s->mdr);
-
- if (dummy) {
- dummy = 0;
- } else {
- rdcount++;
- }
-
- if (wait_for_pin (&status)) {
- return -4;
- }
- }
-
- mpc_reg_out (®s->mcr, I2C_TXAK, I2C_TXAK);
- buf[rdcount++] = mpc_reg_in (®s->mdr);
-
- if (wait_for_pin (&status)) {
- return -5;
- }
-
- mpc_reg_out (®s->mcr, 0, I2C_TXAK);
-
- return 0;
-}
-
-/**************** I2C API ****************/
-
-void i2c_init (int speed, int saddr)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- int i;
-
- for (i = 0; i < I2C_BUS_CNT; i++){
- volatile i2c512x_dev_t *regs = &im->i2c.dev[i];
-
- mpc_reg_out (®s->mcr, 0, 0);
-
- /* Set clock */
- mpc_reg_out (®s->mfdr, mpc_get_fdr (speed), 0);
- mpc_reg_out (®s->madr, saddr << 1, 0);
-
- /* Enable module */
- mpc_reg_out (®s->mcr, I2C_EN, I2C_INIT_MASK);
- mpc_reg_out (®s->msr, 0, I2C_IF);
- }
-
- /* Disable interrupts */
- out_be32(&im->i2c.icr, 0);
-
- /* Turn off filters */
- out_be32(&im->i2c.mifr, 0);
-}
-
-static int mpc_get_fdr (int speed)
-{
- static int fdr = -1;
-
- if (fdr == -1) {
- ulong best_speed = 0;
- ulong divider;
- ulong ips, scl;
- ulong bestmatch = 0xffffffffUL;
- int best_i = 0, best_j = 0, i, j;
- int SCL_Tap[] = { 9, 10, 12, 15, 5, 6, 7, 8};
- struct mpc512x_i2c_tap scltap[] = {
- {4, 1},
- {4, 2},
- {6, 4},
- {6, 8},
- {14, 16},
- {30, 32},
- {62, 64},
- {126, 128}
- };
-
- ips = gd->arch.ips_clk;
- for (i = 7; i >= 0; i--) {
- for (j = 7; j >= 0; j--) {
- scl = 2 * (scltap[j].scl2tap +
- (SCL_Tap[i] - 1) * scltap[j].tap2tap
- + 2);
- if (ips <= speed*scl) {
- if ((speed*scl - ips) < bestmatch) {
- bestmatch = speed*scl - ips;
- best_i = i;
- best_j = j;
- best_speed = ips/scl;
- }
- }
- }
- }
- divider = (best_i & 3) | ((best_i & 4) << 3) | (best_j << 2);
- if (gd->flags & GD_FLG_RELOC) {
- fdr = divider;
- } else {
- debug("%ld kHz, \n", best_speed / 1000);
- return divider;
- }
- }
-
- return fdr;
-}
-
-int i2c_probe (uchar chip)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- int i;
-
- for (i = 0; i < I2C_RETRIES; i++) {
- mpc_reg_out (®s->mcr, I2C_STA, I2C_STA);
-
- if (! do_address (chip, 0)) {
- mpc_reg_out (®s->mcr, 0, I2C_STA);
- udelay (500);
- break;
- }
-
- mpc_reg_out (®s->mcr, 0, I2C_STA);
- udelay (500);
- }
-
- return (i == I2C_RETRIES);
-}
-
-int i2c_read (uchar chip, uint addr, int alen, uchar *buf, int len)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- char xaddr[4];
- int ret = -1;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
- if (wait_for_bb ()) {
- printf ("i2c_read: bus is busy\n");
- goto Done;
- }
-
- mpc_reg_out (®s->mcr, I2C_STA, I2C_STA);
- if (do_address (chip, 0)) {
- printf ("i2c_read: failed to address chip\n");
- goto Done;
- }
-
- if (send_bytes (chip, &xaddr[4-alen], alen)) {
- printf ("i2c_read: send_bytes failed\n");
- goto Done;
- }
-
- mpc_reg_out (®s->mcr, I2C_RSTA, I2C_RSTA);
- if (do_address (chip, 1)) {
- printf ("i2c_read: failed to address chip\n");
- goto Done;
- }
-
- if (receive_bytes (chip, (char *)buf, len)) {
- printf ("i2c_read: receive_bytes failed\n");
- goto Done;
- }
-
- ret = 0;
-Done:
- mpc_reg_out (®s->mcr, 0, I2C_STA);
- return ret;
-}
-
-int i2c_write (uchar chip, uint addr, int alen, uchar *buf, int len)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num];
- char xaddr[4];
- int ret = -1;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
- if (wait_for_bb ()) {
- printf ("i2c_write: bus is busy\n");
- goto Done;
- }
-
- mpc_reg_out (®s->mcr, I2C_STA, I2C_STA);
- if (do_address (chip, 0)) {
- printf ("i2c_write: failed to address chip\n");
- goto Done;
- }
-
- if (send_bytes (chip, &xaddr[4-alen], alen)) {
- printf ("i2c_write: send_bytes failed\n");
- goto Done;
- }
-
- if (send_bytes (chip, (char *)buf, len)) {
- printf ("i2c_write: send_bytes failed\n");
- goto Done;
- }
-
- ret = 0;
-Done:
- mpc_reg_out (®s->mcr, 0, I2C_STA);
- return ret;
-}
-
-int i2c_set_bus_num (unsigned int bus)
-{
- if (bus >= I2C_BUS_CNT) {
- return -1;
- }
- bus_num = bus;
-
- return 0;
-}
-
-unsigned int i2c_get_bus_num (void)
-{
- return bus_num;
-}
-
-#endif /* CONFIG_HARD_I2C */
extra-y += traps.o
obj-y += io.o
obj-y += firmware_sc_task_bestcomm.impl.o
-obj-y += i2c.o
obj-y += cpu.o
obj-y += cpu_init.o
obj-y += ide.o
+++ /dev/null
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_HARD_I2C
-
-#include <mpc5xxx.h>
-#include <i2c.h>
-
-#if !defined(CONFIG_I2C_MULTI_BUS)
-#if (CONFIG_SYS_I2C_MODULE == 2)
-#define I2C_BASE MPC5XXX_I2C2
-#elif (CONFIG_SYS_I2C_MODULE == 1)
-#define I2C_BASE MPC5XXX_I2C1
-#else
-#error CONFIG_SYS_I2C_MODULE is not properly configured
-#endif
-#else
-static unsigned int i2c_bus_num __attribute__ ((section (".data"))) =
- CONFIG_SYS_SPD_BUS_NUM;
-static unsigned int i2c_bus_speed[2] = {CONFIG_SYS_I2C_SPEED,
- CONFIG_SYS_I2C_SPEED};
-
-static const unsigned long i2c_dev[2] = {
- MPC5XXX_I2C1,
- MPC5XXX_I2C2,
-};
-
-#define I2C_BASE ((struct mpc5xxx_i2c *)i2c_dev[i2c_bus_num])
-#endif
-
-#define I2C_TIMEOUT 6667
-#define I2C_RETRIES 3
-
-struct mpc5xxx_i2c_tap {
- int scl2tap;
- int tap2tap;
-};
-
-static int mpc_reg_in (volatile u32 *reg);
-static void mpc_reg_out (volatile u32 *reg, int val, int mask);
-static int wait_for_bb (void);
-static int wait_for_pin (int *status);
-static int do_address (uchar chip, char rdwr_flag);
-static int send_bytes (uchar chip, char *buf, int len);
-static int receive_bytes (uchar chip, char *buf, int len);
-static int mpc_get_fdr (int);
-
-static int mpc_reg_in(volatile u32 *reg)
-{
- int ret = *reg >> 24;
- __asm__ __volatile__ ("eieio");
- return ret;
-}
-
-static void mpc_reg_out(volatile u32 *reg, int val, int mask)
-{
- int tmp;
-
- if (!mask) {
- *reg = val << 24;
- } else {
- tmp = mpc_reg_in(reg);
- *reg = ((tmp & ~mask) | (val & mask)) << 24;
- }
- __asm__ __volatile__ ("eieio");
-
- return;
-}
-
-static int wait_for_bb(void)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int timeout = I2C_TIMEOUT;
- int status;
-
- status = mpc_reg_in(®s->msr);
-
- while (timeout-- && (status & I2C_BB)) {
- mpc_reg_out(®s->mcr, I2C_STA, I2C_STA);
- (void)mpc_reg_in(®s->mdr);
- mpc_reg_out(®s->mcr, 0, I2C_STA);
- mpc_reg_out(®s->mcr, 0, 0);
- mpc_reg_out(®s->mcr, I2C_EN, 0);
- udelay(15);
- status = mpc_reg_in(®s->msr);
- }
-
- return (status & I2C_BB);
-}
-
-static int wait_for_pin(int *status)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int timeout = I2C_TIMEOUT;
-
- *status = mpc_reg_in(®s->msr);
-
- while (timeout-- && !(*status & I2C_IF)) {
- udelay(15);
- *status = mpc_reg_in(®s->msr);
- }
-
- if (!(*status & I2C_IF)) {
- return -1;
- }
-
- mpc_reg_out(®s->msr, 0, I2C_IF);
-
- return 0;
-}
-
-static int do_address(uchar chip, char rdwr_flag)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int status;
-
- chip <<= 1;
-
- if (rdwr_flag) {
- chip |= 1;
- }
-
- mpc_reg_out(®s->mcr, I2C_TX, I2C_TX);
- mpc_reg_out(®s->mdr, chip, 0);
-
- if (wait_for_pin(&status)) {
- return -2;
- }
-
- if (status & I2C_RXAK) {
- return -3;
- }
-
- return 0;
-}
-
-static int send_bytes(uchar chip, char *buf, int len)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int wrcount;
- int status;
-
- for (wrcount = 0; wrcount < len; ++wrcount) {
-
- mpc_reg_out(®s->mdr, buf[wrcount], 0);
-
- if (wait_for_pin(&status)) {
- break;
- }
-
- if (status & I2C_RXAK) {
- break;
- }
-
- }
-
- return !(wrcount == len);
-}
-
-static int receive_bytes(uchar chip, char *buf, int len)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int dummy = 1;
- int rdcount = 0;
- int status;
- int i;
-
- mpc_reg_out(®s->mcr, 0, I2C_TX);
-
- for (i = 0; i < len; ++i) {
- buf[rdcount] = mpc_reg_in(®s->mdr);
-
- if (dummy) {
- dummy = 0;
- } else {
- rdcount++;
- }
-
-
- if (wait_for_pin(&status)) {
- return -4;
- }
- }
-
- mpc_reg_out(®s->mcr, I2C_TXAK, I2C_TXAK);
- buf[rdcount++] = mpc_reg_in(®s->mdr);
-
- if (wait_for_pin(&status)) {
- return -5;
- }
-
- mpc_reg_out(®s->mcr, 0, I2C_TXAK);
-
- return 0;
-}
-
-#if defined(CONFIG_SYS_I2C_INIT_MPC5XXX)
-
-#define FDR510(x) (u8) (((x & 0x20) >> 3) | (x & 0x3))
-#define FDR432(x) (u8) ((x & 0x1C) >> 2)
-/*
- * Reset any i2c devices that may have been interrupted during a system reset.
- * Normally this would be accomplished by clocking the line until SCL and SDA
- * are released and then sending a start condtiion (From an Atmel datasheet).
- * There is no direct access to the i2c pins so instead create start commands
- * through the i2c interface. Send a start command then delay for the SDA Hold
- * time, repeat this by disabling/enabling the bus a total of 9 times.
- */
-static void send_reset(void)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int i;
- u32 delay;
- u8 fdr;
- int SDA_Tap[] = { 3, 3, 4, 4, 1, 1, 2, 2};
- struct mpc5xxx_i2c_tap scltap[] = {
- {4, 1},
- {4, 2},
- {6, 4},
- {6, 8},
- {14, 16},
- {30, 32},
- {62, 64},
- {126, 128}
- };
-
- fdr = (u8)mpc_reg_in(®s->mfdr);
-
- delay = scltap[FDR432(fdr)].scl2tap + ((SDA_Tap[FDR510(fdr)] - 1) * \
- scltap[FDR432(fdr)].tap2tap) + 3;
-
- for (i = 0; i < 9; i++) {
- mpc_reg_out(®s->mcr, I2C_EN|I2C_STA|I2C_TX, I2C_INIT_MASK);
- udelay(delay);
- mpc_reg_out(®s->mcr, 0, I2C_INIT_MASK);
- udelay(delay);
- }
-
- mpc_reg_out(®s->mcr, I2C_EN, I2C_INIT_MASK);
-}
-#endif /* CONFIG_SYS_I2c_INIT_MPC5XXX */
-
-/**************** I2C API ****************/
-
-void i2c_init(int speed, int saddr)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
-
- mpc_reg_out(®s->mcr, 0, 0);
- mpc_reg_out(®s->madr, saddr << 1, 0);
-
- /* Set clock
- */
- mpc_reg_out(®s->mfdr, mpc_get_fdr(speed), 0);
-
- /* Enable module
- */
- mpc_reg_out(®s->mcr, I2C_EN, I2C_INIT_MASK);
- mpc_reg_out(®s->msr, 0, I2C_IF);
-
-#if defined(CONFIG_SYS_I2C_INIT_MPC5XXX)
- send_reset();
-#endif
- return;
-}
-
-static int mpc_get_fdr(int speed)
-{
- static int fdr = -1;
-
- if (fdr == -1) {
- ulong best_speed = 0;
- ulong divider;
- ulong ipb, scl;
- ulong bestmatch = 0xffffffffUL;
- int best_i = 0, best_j = 0, i, j;
- int SCL_Tap[] = { 9, 10, 12, 15, 5, 6, 7, 8};
- struct mpc5xxx_i2c_tap scltap[] = {
- {4, 1},
- {4, 2},
- {6, 4},
- {6, 8},
- {14, 16},
- {30, 32},
- {62, 64},
- {126, 128}
- };
-
- ipb = gd->arch.ipb_clk;
- for (i = 7; i >= 0; i--) {
- for (j = 7; j >= 0; j--) {
- scl = 2 * (scltap[j].scl2tap +
- (SCL_Tap[i] - 1) * scltap[j].tap2tap + 2);
- if (ipb <= speed*scl) {
- if ((speed*scl - ipb) < bestmatch) {
- bestmatch = speed*scl - ipb;
- best_i = i;
- best_j = j;
- best_speed = ipb/scl;
- }
- }
- }
- }
- divider = (best_i & 3) | ((best_i & 4) << 3) | (best_j << 2);
- if (gd->flags & GD_FLG_RELOC) {
- fdr = divider;
- } else {
- printf("%ld kHz, ", best_speed / 1000);
- return divider;
- }
- }
-
- return fdr;
-}
-
-int i2c_probe(uchar chip)
-{
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int i;
-
- for (i = 0; i < I2C_RETRIES; i++) {
- mpc_reg_out(®s->mcr, I2C_STA, I2C_STA);
-
- if (! do_address(chip, 0)) {
- mpc_reg_out(®s->mcr, 0, I2C_STA);
- udelay(500);
- break;
- }
-
- mpc_reg_out(®s->mcr, 0, I2C_STA);
- udelay(500);
- }
-
- return (i == I2C_RETRIES);
-}
-
-int i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len)
-{
- char xaddr[4];
- struct mpc5xxx_i2c * regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int ret = -1;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
- if (wait_for_bb()) {
- printf("i2c_read: bus is busy\n");
- goto Done;
- }
-
- mpc_reg_out(®s->mcr, I2C_STA, I2C_STA);
- if (do_address(chip, 0)) {
- printf("i2c_read: failed to address chip\n");
- goto Done;
- }
-
- if (send_bytes(chip, &xaddr[4-alen], alen)) {
- printf("i2c_read: send_bytes failed\n");
- goto Done;
- }
-
- mpc_reg_out(®s->mcr, I2C_RSTA, I2C_RSTA);
- if (do_address(chip, 1)) {
- printf("i2c_read: failed to address chip\n");
- goto Done;
- }
-
- if (receive_bytes(chip, (char *)buf, len)) {
- printf("i2c_read: receive_bytes failed\n");
- goto Done;
- }
-
- ret = 0;
-Done:
- mpc_reg_out(®s->mcr, 0, I2C_STA);
- return ret;
-}
-
-int i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len)
-{
- char xaddr[4];
- struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
- int ret = -1;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
- if (wait_for_bb()) {
- printf("i2c_write: bus is busy\n");
- goto Done;
- }
-
- mpc_reg_out(®s->mcr, I2C_STA, I2C_STA);
- if (do_address(chip, 0)) {
- printf("i2c_write: failed to address chip\n");
- goto Done;
- }
-
- if (send_bytes(chip, &xaddr[4-alen], alen)) {
- printf("i2c_write: send_bytes failed\n");
- goto Done;
- }
-
- if (send_bytes(chip, (char *)buf, len)) {
- printf("i2c_write: send_bytes failed\n");
- goto Done;
- }
-
- ret = 0;
-Done:
- mpc_reg_out(®s->mcr, 0, I2C_STA);
- return ret;
-}
-
-#if defined(CONFIG_I2C_MULTI_BUS)
-int i2c_set_bus_num(unsigned int bus)
-{
- if (bus > 1)
- return -1;
-
- i2c_bus_num = bus;
- i2c_init(i2c_bus_speed[bus], CONFIG_SYS_I2C_SLAVE);
- return 0;
-}
-
-int i2c_set_bus_speed(unsigned int speed)
-{
- i2c_init(speed, CONFIG_SYS_I2C_SLAVE);
- return 0;
-}
-
-unsigned int i2c_get_bus_num(void)
-{
- return i2c_bus_num;
-}
-
-unsigned int i2c_get_bus_speed(void)
-{
- return i2c_bus_speed[i2c_bus_num];
-}
-#endif
-
-
-#endif /* CONFIG_HARD_I2C */
extra-y = start.o
obj-y = traps.o serial_smc.o serial_scc.o cpu.o cpu_init.o speed.o \
- interrupts.o ether_fcc.o i2c.o commproc.o \
+ interrupts.o ether_fcc.o commproc.o \
bedbug_603e.o pci.o spi.o kgdb.o
obj-$(CONFIG_ETHER_ON_SCC) += ether_scc.o
do { /* Spin until command processed */
__asm__ __volatile__ ("eieio");
} while ((immr->im_cpm.cp_cpcr & CPM_CR_FLG) && ++count < 1000000);
-
-#ifdef CONFIG_HARD_I2C
- immr->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)] = 0;
-#endif
}
/* Allocate some memory from the dual ported ram.
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Paolo Scaffardi, AIRVENT SAM s.p.a - RIMINI(ITALY), arsenio@tin.it
- *
- * (C) Copyright 2000 Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <console.h>
-
-#if defined(CONFIG_HARD_I2C)
-
-#include <asm/cpm_8260.h>
-#include <i2c.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#if defined(CONFIG_I2C_MULTI_BUS)
-static unsigned int i2c_bus_num __attribute__ ((section(".data"))) = 0;
-#endif /* CONFIG_I2C_MULTI_BUS */
-
-/* uSec to wait between polls of the i2c */
-#define DELAY_US 100
-/* uSec to wait for the CPM to start processing the buffer */
-#define START_DELAY_US 1000
-
-/*
- * tx/rx per-byte timeout: we delay DELAY_US uSec between polls so the
- * timeout will be (tx_length + rx_length) * DELAY_US * TOUT_LOOP
- */
-#define TOUT_LOOP 5
-
-/*
- * Set default values
- */
-#ifndef CONFIG_SYS_I2C_SPEED
-#define CONFIG_SYS_I2C_SPEED 50000
-#endif
-
-
-typedef void (*i2c_ecb_t) (int, int, void *); /* error callback function */
-
-/* This structure keeps track of the bd and buffer space usage. */
-typedef struct i2c_state {
- int rx_idx; /* index to next free Rx BD */
- int tx_idx; /* index to next free Tx BD */
- void *rxbd; /* pointer to next free Rx BD */
- void *txbd; /* pointer to next free Tx BD */
- int tx_space; /* number of Tx bytes left */
- unsigned char *tx_buf; /* pointer to free Tx area */
- i2c_ecb_t err_cb; /* error callback function */
- void *cb_data; /* private data to be passed */
-} i2c_state_t;
-
-/* flags for i2c_send() and i2c_receive() */
-#define I2CF_ENABLE_SECONDARY 0x01 /* secondary_address is valid */
-#define I2CF_START_COND 0x02 /* tx: generate start condition */
-#define I2CF_STOP_COND 0x04 /* tx: generate stop condition */
-
-/* return codes */
-#define I2CERR_NO_BUFFERS 1 /* no more BDs or buffer space */
-#define I2CERR_MSG_TOO_LONG 2 /* tried to send/receive to much data */
-#define I2CERR_TIMEOUT 3 /* timeout in i2c_doio() */
-#define I2CERR_QUEUE_EMPTY 4 /* i2c_doio called without send/rcv */
-#define I2CERR_IO_ERROR 5 /* had an error during comms */
-
-/* error callback flags */
-#define I2CECB_RX_ERR 0x10 /* this is a receive error */
-#define I2CECB_RX_OV 0x02 /* receive overrun error */
-#define I2CECB_RX_MASK 0x0f /* mask for error bits */
-#define I2CECB_TX_ERR 0x20 /* this is a transmit error */
-#define I2CECB_TX_CL 0x01 /* transmit collision error */
-#define I2CECB_TX_UN 0x02 /* transmit underflow error */
-#define I2CECB_TX_NAK 0x04 /* transmit no ack error */
-#define I2CECB_TX_MASK 0x0f /* mask for error bits */
-#define I2CECB_TIMEOUT 0x40 /* this is a timeout error */
-
-#define ERROR_I2C_NONE 0
-#define ERROR_I2C_LENGTH 1
-
-#define I2C_WRITE_BIT 0x00
-#define I2C_READ_BIT 0x01
-
-#define I2C_RXTX_LEN 128 /* maximum tx/rx buffer length */
-
-
-#define NUM_RX_BDS 4
-#define NUM_TX_BDS 4
-#define MAX_TX_SPACE 256
-
-typedef struct I2C_BD {
- unsigned short status;
- unsigned short length;
- unsigned char *addr;
-} I2C_BD;
-
-#define BD_I2C_TX_START 0x0400 /* special status for i2c: Start condition */
-
-#define BD_I2C_TX_CL 0x0001 /* collision error */
-#define BD_I2C_TX_UN 0x0002 /* underflow error */
-#define BD_I2C_TX_NAK 0x0004 /* no acknowledge error */
-#define BD_I2C_TX_ERR (BD_I2C_TX_NAK|BD_I2C_TX_UN|BD_I2C_TX_CL)
-
-#define BD_I2C_RX_ERR BD_SC_OV
-
-/*
- * Returns the best value of I2BRG to meet desired clock speed of I2C with
- * input parameters (clock speed, filter, and predivider value).
- * It returns computer speed value and the difference between it and desired
- * speed.
- */
-static inline int
-i2c_roundrate(int hz, int speed, int filter, int modval,
- int *brgval, int *totspeed)
-{
- int moddiv = 1 << (5 - (modval & 3)), brgdiv, div;
-
- debug("\t[I2C] trying hz=%d, speed=%d, filter=%d, modval=%d\n",
- hz, speed, filter, modval);
-
- div = moddiv * speed;
- brgdiv = (hz + div - 1) / div;
-
- debug("\t\tmoddiv=%d, brgdiv=%d\n", moddiv, brgdiv);
-
- *brgval = ((brgdiv + 1) / 2) - 3 - (2 * filter);
-
- if ((*brgval < 0) || (*brgval > 255)) {
- debug("\t\trejected brgval=%d\n", *brgval);
- return -1;
- }
-
- brgdiv = 2 * (*brgval + 3 + (2 * filter));
- div = moddiv * brgdiv;
- *totspeed = hz / div;
-
- debug("\t\taccepted brgval=%d, totspeed=%d\n", *brgval, *totspeed);
-
- return 0;
-}
-
-/*
- * Sets the I2C clock predivider and divider to meet required clock speed.
- */
-static int i2c_setrate(int hz, int speed)
-{
- immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c;
- int brgval,
- modval, /* 0-3 */
- bestspeed_diff = speed,
- bestspeed_brgval = 0,
- bestspeed_modval = 0,
- bestspeed_filter = 0,
- totspeed,
- filter = 0; /* Use this fixed value */
-
- for (modval = 0; modval < 4; modval++) {
- if (i2c_roundrate(hz, speed, filter, modval, &brgval, &totspeed)
- == 0) {
- int diff = speed - totspeed;
-
- if ((diff >= 0) && (diff < bestspeed_diff)) {
- bestspeed_diff = diff;
- bestspeed_modval = modval;
- bestspeed_brgval = brgval;
- bestspeed_filter = filter;
- }
- }
- }
-
- debug("[I2C] Best is:\n");
- debug("[I2C] CPU=%dhz RATE=%d F=%d I2MOD=%08x I2BRG=%08x DIFF=%dhz\n",
- hz, speed, bestspeed_filter, bestspeed_modval, bestspeed_brgval,
- bestspeed_diff);
-
- i2c->i2c_i2mod |= ((bestspeed_modval & 3) << 1) |
- (bestspeed_filter << 3);
- i2c->i2c_i2brg = bestspeed_brgval & 0xff;
-
- debug("[I2C] i2mod=%08x i2brg=%08x\n", i2c->i2c_i2mod,
- i2c->i2c_i2brg);
-
- return 1;
-}
-
-void i2c_init(int speed, int slaveadd)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8260_t *cp = (cpm8260_t *)&immap->im_cpm;
- volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c;
- volatile iic_t *iip;
- ulong rbase, tbase;
- volatile I2C_BD *rxbd, *txbd;
- uint dpaddr;
-
-#ifdef CONFIG_SYS_I2C_INIT_BOARD
- /*
- * call board specific i2c bus reset routine before accessing the
- * environment, which might be in a chip on that bus. For details
- * about this problem see doc/I2C_Edge_Conditions.
- */
- i2c_init_board();
-#endif
-
- dpaddr = immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)];
- if (dpaddr == 0) {
- /* need to allocate dual port ram */
- dpaddr = m8260_cpm_dpalloc(64 +
- (NUM_RX_BDS * sizeof(I2C_BD)) +
- (NUM_TX_BDS * sizeof(I2C_BD)) +
- MAX_TX_SPACE, 64);
- immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)] =
- dpaddr;
- }
-
- /*
- * initialise data in dual port ram:
- *
- * dpaddr -> parameter ram (64 bytes)
- * rbase -> rx BD (NUM_RX_BDS * sizeof(I2C_BD) bytes)
- * tbase -> tx BD (NUM_TX_BDS * sizeof(I2C_BD) bytes)
- * tx buffer (MAX_TX_SPACE bytes)
- */
-
- iip = (iic_t *)&immap->im_dprambase[dpaddr];
- memset((void *)iip, 0, sizeof(iic_t));
-
- rbase = dpaddr + 64;
- tbase = rbase + NUM_RX_BDS * sizeof(I2C_BD);
-
- /* Disable interrupts */
- i2c->i2c_i2mod = 0x00;
- i2c->i2c_i2cmr = 0x00;
- i2c->i2c_i2cer = 0xff;
- i2c->i2c_i2add = slaveadd;
-
- /*
- * Set the I2C BRG Clock division factor from desired i2c rate
- * and current CPU rate (we assume sccr dfbgr field is 0;
- * divide BRGCLK by 1)
- */
- debug("[I2C] Setting rate...\n");
- i2c_setrate(gd->arch.brg_clk, CONFIG_SYS_I2C_SPEED);
-
- /* Set I2C controller in master mode */
- i2c->i2c_i2com = 0x01;
-
- /* Initialize Tx/Rx parameters */
- iip->iic_rbase = rbase;
- iip->iic_tbase = tbase;
- rxbd = (I2C_BD *)((unsigned char *) &immap->
- im_dprambase[iip->iic_rbase]);
- txbd = (I2C_BD *)((unsigned char *) &immap->
- im_dprambase[iip->iic_tbase]);
-
- debug("[I2C] rbase = %04x\n", iip->iic_rbase);
- debug("[I2C] tbase = %04x\n", iip->iic_tbase);
- debug("[I2C] rxbd = %08x\n", (int) rxbd);
- debug("[I2C] txbd = %08x\n", (int) txbd);
-
- /* Set big endian byte order */
- iip->iic_tfcr = 0x10;
- iip->iic_rfcr = 0x10;
-
- /* Set maximum receive size. */
- iip->iic_mrblr = I2C_RXTX_LEN;
-
- cp->cp_cpcr = mk_cr_cmd(CPM_CR_I2C_PAGE,
- CPM_CR_I2C_SBLOCK,
- 0x00, CPM_CR_INIT_TRX) | CPM_CR_FLG;
- do {
- __asm__ __volatile__("eieio");
- } while (cp->cp_cpcr & CPM_CR_FLG);
-
- /* Clear events and interrupts */
- i2c->i2c_i2cer = 0xff;
- i2c->i2c_i2cmr = 0x00;
-}
-
-static
-void i2c_newio(i2c_state_t *state)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile iic_t *iip;
- uint dpaddr;
-
- debug("[I2C] i2c_newio\n");
-
- dpaddr = immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)];
- iip = (iic_t *)&immap->im_dprambase[dpaddr];
- state->rx_idx = 0;
- state->tx_idx = 0;
- state->rxbd = (void *)&immap->im_dprambase[iip->iic_rbase];
- state->txbd = (void *)&immap->im_dprambase[iip->iic_tbase];
- state->tx_space = MAX_TX_SPACE;
- state->tx_buf = (uchar *)state->txbd + NUM_TX_BDS * sizeof(I2C_BD);
- state->err_cb = NULL;
- state->cb_data = NULL;
-
- debug("[I2C] rxbd = %08x\n", (int)state->rxbd);
- debug("[I2C] txbd = %08x\n", (int)state->txbd);
- debug("[I2C] tx_buf = %08x\n", (int)state->tx_buf);
-
- /* clear the buffer memory */
- memset((char *) state->tx_buf, 0, MAX_TX_SPACE);
-}
-
-static
-int i2c_send(i2c_state_t *state,
- unsigned char address,
- unsigned char secondary_address,
- unsigned int flags, unsigned short size, unsigned char *dataout)
-{
- volatile I2C_BD *txbd;
- int i, j;
-
- debug("[I2C] i2c_send add=%02d sec=%02d flag=%02d size=%d\n",
- address, secondary_address, flags, size);
-
- /* trying to send message larger than BD */
- if (size > I2C_RXTX_LEN)
- return I2CERR_MSG_TOO_LONG;
-
- /* no more free bds */
- if (state->tx_idx >= NUM_TX_BDS || state->tx_space < (2 + size))
- return I2CERR_NO_BUFFERS;
-
- txbd = (I2C_BD *)state->txbd;
- txbd->addr = state->tx_buf;
-
- debug("[I2C] txbd = %08x\n", (int) txbd);
-
- if (flags & I2CF_START_COND) {
- debug("[I2C] Formatting addresses...\n");
- if (flags & I2CF_ENABLE_SECONDARY) {
- /* Length of message plus dest addresses */
- txbd->length = size + 2;
- txbd->addr[0] = address << 1;
- txbd->addr[1] = secondary_address;
- i = 2;
- } else {
- /* Length of message plus dest address */
- txbd->length = size + 1;
- /* Write destination address to BD */
- txbd->addr[0] = address << 1;
- i = 1;
- }
- } else {
- txbd->length = size; /* Length of message */
- i = 0;
- }
-
- /* set up txbd */
- txbd->status = BD_SC_READY;
- if (flags & I2CF_START_COND)
- txbd->status |= BD_I2C_TX_START;
- if (flags & I2CF_STOP_COND)
- txbd->status |= BD_SC_LAST | BD_SC_WRAP;
-
- /* Copy data to send into buffer */
- debug("[I2C] copy data...\n");
- for (j = 0; j < size; i++, j++)
- txbd->addr[i] = dataout[j];
-
- debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
- txbd->length, txbd->status, txbd->addr[0], txbd->addr[1]);
-
- /* advance state */
- state->tx_buf += txbd->length;
- state->tx_space -= txbd->length;
- state->tx_idx++;
- state->txbd = (void *) (txbd + 1);
-
- return 0;
-}
-
-static
-int i2c_receive(i2c_state_t *state,
- unsigned char address,
- unsigned char secondary_address,
- unsigned int flags,
- unsigned short size_to_expect, unsigned char *datain)
-{
- volatile I2C_BD *rxbd, *txbd;
-
- debug("[I2C] i2c_receive %02d %02d %02d\n", address,
- secondary_address, flags);
-
- /* Expected to receive too much */
- if (size_to_expect > I2C_RXTX_LEN)
- return I2CERR_MSG_TOO_LONG;
-
- /* no more free bds */
- if (state->tx_idx >= NUM_TX_BDS || state->rx_idx >= NUM_RX_BDS
- || state->tx_space < 2)
- return I2CERR_NO_BUFFERS;
-
- rxbd = (I2C_BD *) state->rxbd;
- txbd = (I2C_BD *) state->txbd;
-
- debug("[I2C] rxbd = %08x\n", (int) rxbd);
- debug("[I2C] txbd = %08x\n", (int) txbd);
-
- txbd->addr = state->tx_buf;
-
- /* set up TXBD for destination address */
- if (flags & I2CF_ENABLE_SECONDARY) {
- txbd->length = 2;
- txbd->addr[0] = address << 1; /* Write data */
- txbd->addr[1] = secondary_address; /* Internal address */
- txbd->status = BD_SC_READY;
- } else {
- txbd->length = 1 + size_to_expect;
- txbd->addr[0] = (address << 1) | 0x01;
- txbd->status = BD_SC_READY;
- memset(&txbd->addr[1], 0, txbd->length);
- }
-
- /* set up rxbd for reception */
- rxbd->status = BD_SC_EMPTY;
- rxbd->length = size_to_expect;
- rxbd->addr = datain;
-
- txbd->status |= BD_I2C_TX_START;
- if (flags & I2CF_STOP_COND) {
- txbd->status |= BD_SC_LAST | BD_SC_WRAP;
- rxbd->status |= BD_SC_WRAP;
- }
-
- debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
- txbd->length, txbd->status, txbd->addr[0], txbd->addr[1]);
- debug("[I2C] rxbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
- rxbd->length, rxbd->status, rxbd->addr[0], rxbd->addr[1]);
-
- /* advance state */
- state->tx_buf += txbd->length;
- state->tx_space -= txbd->length;
- state->tx_idx++;
- state->txbd = (void *) (txbd + 1);
- state->rx_idx++;
- state->rxbd = (void *) (rxbd + 1);
-
- return 0;
-}
-
-
-static
-int i2c_doio(i2c_state_t *state)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile iic_t *iip;
- volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c;
- volatile I2C_BD *txbd, *rxbd;
- int n, i, b, rxcnt = 0, rxtimeo = 0, txcnt = 0, txtimeo = 0, rc = 0;
- uint dpaddr;
-
- debug("[I2C] i2c_doio\n");
-
- if (state->tx_idx <= 0 && state->rx_idx <= 0) {
- debug("[I2C] No I/O is queued\n");
- return I2CERR_QUEUE_EMPTY;
- }
-
- dpaddr = immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)];
- iip = (iic_t *)&immap->im_dprambase[dpaddr];
- iip->iic_rbptr = iip->iic_rbase;
- iip->iic_tbptr = iip->iic_tbase;
-
- /* Enable I2C */
- debug("[I2C] Enabling I2C...\n");
- i2c->i2c_i2mod |= 0x01;
-
- /* Begin transmission */
- i2c->i2c_i2com |= 0x80;
-
- /* Loop until transmit & receive completed */
-
- n = state->tx_idx;
-
- if (n > 0) {
-
- txbd = ((I2C_BD *) state->txbd) - n;
- for (i = 0; i < n; i++) {
- txtimeo += TOUT_LOOP * txbd->length;
- txbd++;
- }
-
- txbd--; /* wait until last in list is done */
-
- debug("[I2C] Transmitting...(txbd=0x%08lx)\n",
- (ulong) txbd);
-
- udelay(START_DELAY_US); /* give it time to start */
- while ((txbd->status & BD_SC_READY) && (++txcnt < txtimeo)) {
- udelay(DELAY_US);
- if (ctrlc())
- return -1;
- __asm__ __volatile__("eieio");
- }
- }
-
- n = state->rx_idx;
-
- if (txcnt < txtimeo && n > 0) {
-
- rxbd = ((I2C_BD *) state->rxbd) - n;
- for (i = 0; i < n; i++) {
- rxtimeo += TOUT_LOOP * rxbd->length;
- rxbd++;
- }
-
- rxbd--; /* wait until last in list is done */
-
- debug("[I2C] Receiving...(rxbd=0x%08lx)\n", (ulong) rxbd);
-
- udelay(START_DELAY_US); /* give it time to start */
- while ((rxbd->status & BD_SC_EMPTY) && (++rxcnt < rxtimeo)) {
- udelay(DELAY_US);
- if (ctrlc())
- return -1;
- __asm__ __volatile__("eieio");
- }
- }
-
- /* Turn off I2C */
- i2c->i2c_i2mod &= ~0x01;
-
- n = state->tx_idx;
-
- if (n > 0) {
- for (i = 0; i < n; i++) {
- txbd = ((I2C_BD *) state->txbd) - (n - i);
- b = txbd->status & BD_I2C_TX_ERR;
- if (b != 0) {
- if (state->err_cb != NULL)
- (*state->err_cb) (I2CECB_TX_ERR | b,
- i, state->cb_data);
- if (rc == 0)
- rc = I2CERR_IO_ERROR;
- }
- }
- }
-
- n = state->rx_idx;
-
- if (n > 0) {
- for (i = 0; i < n; i++) {
- rxbd = ((I2C_BD *) state->rxbd) - (n - i);
- b = rxbd->status & BD_I2C_RX_ERR;
- if (b != 0) {
- if (state->err_cb != NULL)
- (*state->err_cb) (I2CECB_RX_ERR | b,
- i, state->cb_data);
- if (rc == 0)
- rc = I2CERR_IO_ERROR;
- }
- }
- }
-
- if ((txtimeo > 0 && txcnt >= txtimeo) ||
- (rxtimeo > 0 && rxcnt >= rxtimeo)) {
- if (state->err_cb != NULL)
- (*state->err_cb) (I2CECB_TIMEOUT, -1, state->cb_data);
- if (rc == 0)
- rc = I2CERR_TIMEOUT;
- }
-
- return rc;
-}
-
-static void i2c_probe_callback(int flags, int xnum, void *data)
-{
- /*
- * the only acceptable errors are a transmit NAK or a receive
- * overrun - tx NAK means the device does not exist, rx OV
- * means the device must have responded to the slave address
- * even though the transfer failed
- */
- if (flags == (I2CECB_TX_ERR | I2CECB_TX_NAK))
- *(int *) data |= 1;
- if (flags == (I2CECB_RX_ERR | I2CECB_RX_OV))
- *(int *) data |= 2;
-}
-
-int i2c_probe(uchar chip)
-{
- i2c_state_t state;
- int rc, err_flag;
- uchar buf[1];
-
- i2c_newio(&state);
-
- state.err_cb = i2c_probe_callback;
- state.cb_data = (void *) &err_flag;
- err_flag = 0;
-
- rc = i2c_receive(&state, chip, 0, I2CF_START_COND | I2CF_STOP_COND, 1,
- buf);
-
- if (rc != 0)
- return rc; /* probe failed */
-
- rc = i2c_doio(&state);
-
- if (rc == 0)
- return 0; /* device exists - read succeeded */
-
- if (rc == I2CERR_TIMEOUT)
- return -1; /* device does not exist - timeout */
-
- if (rc != I2CERR_IO_ERROR || err_flag == 0)
- return rc; /* probe failed */
-
- if (err_flag & 1)
- return -1; /* device does not exist - had transmit NAK */
-
- return 0; /* device exists - had receive overrun */
-}
-
-
-int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
-{
- i2c_state_t state;
- uchar xaddr[4];
- int rc;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
-#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
- /*
- * EEPROM chips that implement "address overflow" are ones
- * like Catalyst 24WC04/08/16 which has 9/10/11 bits of address
- * and the extra bits end up in the "chip address" bit slots.
- * This makes a 24WC08 (1Kbyte) chip look like four 256 byte
- * chips.
- *
- * Note that we consider the length of the address field to still
- * be one byte because the extra address bits are hidden in the
- * chip address.
- */
- chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
-#endif
-
- i2c_newio(&state);
-
- rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen,
- &xaddr[4 - alen]);
- if (rc != 0) {
- printf("i2c_read: i2c_send failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_receive(&state, chip, 0, I2CF_STOP_COND, len, buffer);
- if (rc != 0) {
- printf("i2c_read: i2c_receive failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_doio(&state);
- if (rc != 0) {
- printf("i2c_read: i2c_doio failed (%d)\n", rc);
- return 1;
- }
- return 0;
-}
-
-int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
-{
- i2c_state_t state;
- uchar xaddr[4];
- int rc;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
-#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
- /*
- * EEPROM chips that implement "address overflow" are ones
- * like Catalyst 24WC04/08/16 which has 9/10/11 bits of address
- * and the extra bits end up in the "chip address" bit slots.
- * This makes a 24WC08 (1Kbyte) chip look like four 256 byte
- * chips.
- *
- * Note that we consider the length of the address field to still
- * be one byte because the extra address bits are hidden in the
- * chip address.
- */
- chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
-#endif
-
- i2c_newio(&state);
-
- rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen,
- &xaddr[4 - alen]);
- if (rc != 0) {
- printf("i2c_write: first i2c_send failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_send(&state, 0, 0, I2CF_STOP_COND, len, buffer);
- if (rc != 0) {
- printf("i2c_write: second i2c_send failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_doio(&state);
- if (rc != 0) {
- printf("i2c_write: i2c_doio failed (%d)\n", rc);
- return 1;
- }
- return 0;
-}
-
-#if defined(CONFIG_I2C_MULTI_BUS)
-/*
- * Functions for multiple I2C bus handling
- */
-unsigned int i2c_get_bus_num(void)
-{
- return i2c_bus_num;
-}
-
-int i2c_set_bus_num(unsigned int bus)
-{
- if (bus >= CONFIG_SYS_MAX_I2C_BUS)
- return -1;
- i2c_bus_num = bus;
- return 0;
-}
-
-#endif /* CONFIG_I2C_MULTI_BUS */
-#endif /* CONFIG_HARD_I2C */
obj-y += cpu_init.o
obj-y += fec.o
obj-$(CONFIG_OF_LIBFDT) += fdt.o
-obj-y += i2c.o
obj-y += interrupts.o
obj-y += scc.o
obj-y += serial.o
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Paolo Scaffardi, AIRVENT SAM s.p.a - RIMINI(ITALY), arsenio@tin.it
- *
- * (C) Copyright 2000 Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- *
- * Back ported to the 8xx platform (from the 8260 platform) by
- * Murray.Jensen@cmst.csiro.au, 27-Jan-01.
- */
-
-#include <common.h>
-#include <console.h>
-
-#ifdef CONFIG_HARD_I2C
-
-#include <commproc.h>
-#include <i2c.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* tx/rx timeout (we need the i2c early, so we don't use get_timer()) */
-#define TOUT_LOOP 1000000
-
-#define NUM_RX_BDS 4
-#define NUM_TX_BDS 4
-#define MAX_TX_SPACE 256
-#define I2C_RXTX_LEN 128 /* maximum tx/rx buffer length */
-
-typedef struct I2C_BD {
- unsigned short status;
- unsigned short length;
- unsigned char *addr;
-} I2C_BD;
-
-#define BD_I2C_TX_START 0x0400 /* special status for i2c: Start condition */
-
-#define BD_I2C_TX_CL 0x0001 /* collision error */
-#define BD_I2C_TX_UN 0x0002 /* underflow error */
-#define BD_I2C_TX_NAK 0x0004 /* no acknowledge error */
-#define BD_I2C_TX_ERR (BD_I2C_TX_NAK|BD_I2C_TX_UN|BD_I2C_TX_CL)
-
-#define BD_I2C_RX_ERR BD_SC_OV
-
-typedef void (*i2c_ecb_t) (int, int); /* error callback function */
-
-/* This structure keeps track of the bd and buffer space usage. */
-typedef struct i2c_state {
- int rx_idx; /* index to next free Rx BD */
- int tx_idx; /* index to next free Tx BD */
- void *rxbd; /* pointer to next free Rx BD */
- void *txbd; /* pointer to next free Tx BD */
- int tx_space; /* number of Tx bytes left */
- unsigned char *tx_buf; /* pointer to free Tx area */
- i2c_ecb_t err_cb; /* error callback function */
-} i2c_state_t;
-
-
-/* flags for i2c_send() and i2c_receive() */
-#define I2CF_ENABLE_SECONDARY 0x01 /* secondary_address is valid */
-#define I2CF_START_COND 0x02 /* tx: generate start condition */
-#define I2CF_STOP_COND 0x04 /* tx: generate stop condition */
-
-/* return codes */
-#define I2CERR_NO_BUFFERS 0x01 /* no more BDs or buffer space */
-#define I2CERR_MSG_TOO_LONG 0x02 /* tried to send/receive to much data */
-#define I2CERR_TIMEOUT 0x03 /* timeout in i2c_doio() */
-#define I2CERR_QUEUE_EMPTY 0x04 /* i2c_doio called without send/receive */
-
-/* error callback flags */
-#define I2CECB_RX_ERR 0x10 /* this is a receive error */
-#define I2CECB_RX_ERR_OV 0x02 /* receive overrun error */
-#define I2CECB_RX_MASK 0x0f /* mask for error bits */
-#define I2CECB_TX_ERR 0x20 /* this is a transmit error */
-#define I2CECB_TX_CL 0x01 /* transmit collision error */
-#define I2CECB_TX_UN 0x02 /* transmit underflow error */
-#define I2CECB_TX_NAK 0x04 /* transmit no ack error */
-#define I2CECB_TX_MASK 0x0f /* mask for error bits */
-#define I2CECB_TIMEOUT 0x40 /* this is a timeout error */
-
-/*
- * Returns the best value of I2BRG to meet desired clock speed of I2C with
- * input parameters (clock speed, filter, and predivider value).
- * It returns computer speed value and the difference between it and desired
- * speed.
- */
-static inline int
-i2c_roundrate(int hz, int speed, int filter, int modval,
- int *brgval, int *totspeed)
-{
- int moddiv = 1 << (5 - (modval & 3)), brgdiv, div;
-
- debug("\t[I2C] trying hz=%d, speed=%d, filter=%d, modval=%d\n",
- hz, speed, filter, modval);
-
- div = moddiv * speed;
- brgdiv = (hz + div - 1) / div;
-
- debug("\t\tmoddiv=%d, brgdiv=%d\n", moddiv, brgdiv);
-
- *brgval = ((brgdiv + 1) / 2) - 3 - (2 * filter);
-
- if ((*brgval < 0) || (*brgval > 255)) {
- debug("\t\trejected brgval=%d\n", *brgval);
- return -1;
- }
-
- brgdiv = 2 * (*brgval + 3 + (2 * filter));
- div = moddiv * brgdiv;
- *totspeed = hz / div;
-
- debug("\t\taccepted brgval=%d, totspeed=%d\n", *brgval, *totspeed);
-
- return 0;
-}
-
-/*
- * Sets the I2C clock predivider and divider to meet required clock speed.
- */
-static int i2c_setrate(int hz, int speed)
-{
- immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile i2c8xx_t *i2c = (i2c8xx_t *) & immap->im_i2c;
- int brgval,
- modval, /* 0-3 */
- bestspeed_diff = speed,
- bestspeed_brgval = 0,
- bestspeed_modval = 0,
- bestspeed_filter = 0,
- totspeed,
- filter = 0; /* Use this fixed value */
-
- for (modval = 0; modval < 4; modval++) {
- if (i2c_roundrate
- (hz, speed, filter, modval, &brgval, &totspeed) == 0) {
- int diff = speed - totspeed;
-
- if ((diff >= 0) && (diff < bestspeed_diff)) {
- bestspeed_diff = diff;
- bestspeed_modval = modval;
- bestspeed_brgval = brgval;
- bestspeed_filter = filter;
- }
- }
- }
-
- debug("[I2C] Best is:\n");
- debug("[I2C] CPU=%dhz RATE=%d F=%d I2MOD=%08x I2BRG=%08x DIFF=%dhz\n",
- hz,
- speed,
- bestspeed_filter,
- bestspeed_modval,
- bestspeed_brgval,
- bestspeed_diff);
-
- i2c->i2c_i2mod |=
- ((bestspeed_modval & 3) << 1) | (bestspeed_filter << 3);
- i2c->i2c_i2brg = bestspeed_brgval & 0xff;
-
- debug("[I2C] i2mod=%08x i2brg=%08x\n",
- i2c->i2c_i2mod,
- i2c->i2c_i2brg);
-
- return 1;
-}
-
-void i2c_init(int speed, int slaveaddr)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm;
- volatile i2c8xx_t *i2c = (i2c8xx_t *)&immap->im_i2c;
- volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
- ulong rbase, tbase;
- volatile I2C_BD *rxbd, *txbd;
- uint dpaddr;
-
-#ifdef CONFIG_SYS_I2C_INIT_BOARD
- /* call board specific i2c bus reset routine before accessing the */
- /* environment, which might be in a chip on that bus. For details */
- /* about this problem see doc/I2C_Edge_Conditions. */
- i2c_init_board();
-#endif
-
-#ifdef CONFIG_SYS_I2C_UCODE_PATCH
- iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
-#else
- /* Disable relocation */
- iip->iic_rpbase = 0;
-#endif
-
- dpaddr = CPM_I2C_BASE;
-
- /*
- * initialise data in dual port ram:
- *
- * dpaddr->rbase -> rx BD (NUM_RX_BDS * sizeof(I2C_BD) bytes)
- * tbase -> tx BD (NUM_TX_BDS * sizeof(I2C_BD) bytes)
- * tx buffer (MAX_TX_SPACE bytes)
- */
-
- rbase = dpaddr;
- tbase = rbase + NUM_RX_BDS * sizeof(I2C_BD);
-
- /* Initialize Port B I2C pins. */
- cp->cp_pbpar |= 0x00000030;
- cp->cp_pbdir |= 0x00000030;
- cp->cp_pbodr |= 0x00000030;
-
- /* Disable interrupts */
- i2c->i2c_i2mod = 0x00;
- i2c->i2c_i2cmr = 0x00;
- i2c->i2c_i2cer = 0xff;
- i2c->i2c_i2add = slaveaddr;
-
- /*
- * Set the I2C BRG Clock division factor from desired i2c rate
- * and current CPU rate (we assume sccr dfbgr field is 0;
- * divide BRGCLK by 1)
- */
- debug("[I2C] Setting rate...\n");
- i2c_setrate(gd->cpu_clk, CONFIG_SYS_I2C_SPEED);
-
- /* Set I2C controller in master mode */
- i2c->i2c_i2com = 0x01;
-
- /* Set SDMA bus arbitration level to 5 (SDCR) */
- immap->im_siu_conf.sc_sdcr = 0x0001;
-
- /* Initialize Tx/Rx parameters */
- iip->iic_rbase = rbase;
- iip->iic_tbase = tbase;
- rxbd = (I2C_BD *) ((unsigned char *) &cp->cp_dpmem[iip->iic_rbase]);
- txbd = (I2C_BD *) ((unsigned char *) &cp->cp_dpmem[iip->iic_tbase]);
-
- debug("[I2C] rbase = %04x\n", iip->iic_rbase);
- debug("[I2C] tbase = %04x\n", iip->iic_tbase);
- debug("[I2C] rxbd = %08x\n", (int)rxbd);
- debug("[I2C] txbd = %08x\n", (int)txbd);
-
- /* Set big endian byte order */
- iip->iic_tfcr = 0x10;
- iip->iic_rfcr = 0x10;
-
- /* Set maximum receive size. */
- iip->iic_mrblr = I2C_RXTX_LEN;
-
-#ifdef CONFIG_SYS_I2C_UCODE_PATCH
- /*
- * Initialize required parameters if using microcode patch.
- */
- iip->iic_rbptr = iip->iic_rbase;
- iip->iic_tbptr = iip->iic_tbase;
- iip->iic_rstate = 0;
- iip->iic_tstate = 0;
-#else
- cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_I2C, CPM_CR_INIT_TRX) | CPM_CR_FLG;
- do {
- __asm__ __volatile__("eieio");
- } while (cp->cp_cpcr & CPM_CR_FLG);
-#endif
-
- /* Clear events and interrupts */
- i2c->i2c_i2cer = 0xff;
- i2c->i2c_i2cmr = 0x00;
-}
-
-static void i2c_newio(i2c_state_t *state)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm;
- volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
-
- debug("[I2C] i2c_newio\n");
-
-#ifdef CONFIG_SYS_I2C_UCODE_PATCH
- iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
-#endif
- state->rx_idx = 0;
- state->tx_idx = 0;
- state->rxbd = (void *)&cp->cp_dpmem[iip->iic_rbase];
- state->txbd = (void *)&cp->cp_dpmem[iip->iic_tbase];
- state->tx_space = MAX_TX_SPACE;
- state->tx_buf = (uchar *)state->txbd + NUM_TX_BDS * sizeof(I2C_BD);
- state->err_cb = NULL;
-
- debug("[I2C] rxbd = %08x\n", (int)state->rxbd);
- debug("[I2C] txbd = %08x\n", (int)state->txbd);
- debug("[I2C] tx_buf = %08x\n", (int)state->tx_buf);
-
- /* clear the buffer memory */
- memset((char *)state->tx_buf, 0, MAX_TX_SPACE);
-}
-
-static int
-i2c_send(i2c_state_t *state,
- unsigned char address,
- unsigned char secondary_address,
- unsigned int flags, unsigned short size, unsigned char *dataout)
-{
- volatile I2C_BD *txbd;
- int i, j;
-
- debug("[I2C] i2c_send add=%02d sec=%02d flag=%02d size=%d\n",
- address, secondary_address, flags, size);
-
- /* trying to send message larger than BD */
- if (size > I2C_RXTX_LEN)
- return I2CERR_MSG_TOO_LONG;
-
- /* no more free bds */
- if (state->tx_idx >= NUM_TX_BDS || state->tx_space < (2 + size))
- return I2CERR_NO_BUFFERS;
-
- txbd = (I2C_BD *) state->txbd;
- txbd->addr = state->tx_buf;
-
- debug("[I2C] txbd = %08x\n", (int)txbd);
-
- if (flags & I2CF_START_COND) {
- debug("[I2C] Formatting addresses...\n");
- if (flags & I2CF_ENABLE_SECONDARY) {
- /* Length of msg + dest addr */
- txbd->length = size + 2;
-
- txbd->addr[0] = address << 1;
- txbd->addr[1] = secondary_address;
- i = 2;
- } else {
- /* Length of msg + dest addr */
- txbd->length = size + 1;
- /* Write dest addr to BD */
- txbd->addr[0] = address << 1;
- i = 1;
- }
- } else {
- txbd->length = size; /* Length of message */
- i = 0;
- }
-
- /* set up txbd */
- txbd->status = BD_SC_READY;
- if (flags & I2CF_START_COND)
- txbd->status |= BD_I2C_TX_START;
- if (flags & I2CF_STOP_COND)
- txbd->status |= BD_SC_LAST | BD_SC_WRAP;
-
- /* Copy data to send into buffer */
- debug("[I2C] copy data...\n");
- for(j = 0; j < size; i++, j++)
- txbd->addr[i] = dataout[j];
-
- debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
- txbd->length,
- txbd->status,
- txbd->addr[0],
- txbd->addr[1]);
-
- /* advance state */
- state->tx_buf += txbd->length;
- state->tx_space -= txbd->length;
- state->tx_idx++;
- state->txbd = (void *) (txbd + 1);
-
- return 0;
-}
-
-static int
-i2c_receive(i2c_state_t *state,
- unsigned char address,
- unsigned char secondary_address,
- unsigned int flags,
- unsigned short size_to_expect, unsigned char *datain)
-{
- volatile I2C_BD *rxbd, *txbd;
-
- debug("[I2C] i2c_receive %02d %02d %02d\n",
- address, secondary_address, flags);
-
- /* Expected to receive too much */
- if (size_to_expect > I2C_RXTX_LEN)
- return I2CERR_MSG_TOO_LONG;
-
- /* no more free bds */
- if (state->tx_idx >= NUM_TX_BDS || state->rx_idx >= NUM_RX_BDS
- || state->tx_space < 2)
- return I2CERR_NO_BUFFERS;
-
- rxbd = (I2C_BD *) state->rxbd;
- txbd = (I2C_BD *) state->txbd;
-
- debug("[I2C] rxbd = %08x\n", (int)rxbd);
- debug("[I2C] txbd = %08x\n", (int)txbd);
-
- txbd->addr = state->tx_buf;
-
- /* set up TXBD for destination address */
- if (flags & I2CF_ENABLE_SECONDARY) {
- txbd->length = 2;
- txbd->addr[0] = address << 1; /* Write data */
- txbd->addr[1] = secondary_address; /* Internal address */
- txbd->status = BD_SC_READY;
- } else {
- txbd->length = 1 + size_to_expect;
- txbd->addr[0] = (address << 1) | 0x01;
- txbd->status = BD_SC_READY;
- memset(&txbd->addr[1], 0, txbd->length);
- }
-
- /* set up rxbd for reception */
- rxbd->status = BD_SC_EMPTY;
- rxbd->length = size_to_expect;
- rxbd->addr = datain;
-
- txbd->status |= BD_I2C_TX_START;
- if (flags & I2CF_STOP_COND) {
- txbd->status |= BD_SC_LAST | BD_SC_WRAP;
- rxbd->status |= BD_SC_WRAP;
- }
-
- debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
- txbd->length,
- txbd->status,
- txbd->addr[0],
- txbd->addr[1]);
- debug("[I2C] rxbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n",
- rxbd->length,
- rxbd->status,
- rxbd->addr[0],
- rxbd->addr[1]);
-
- /* advance state */
- state->tx_buf += txbd->length;
- state->tx_space -= txbd->length;
- state->tx_idx++;
- state->txbd = (void *) (txbd + 1);
- state->rx_idx++;
- state->rxbd = (void *) (rxbd + 1);
-
- return 0;
-}
-
-
-static int i2c_doio(i2c_state_t *state)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm;
- volatile i2c8xx_t *i2c = (i2c8xx_t *)&immap->im_i2c;
- volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
- volatile I2C_BD *txbd, *rxbd;
- volatile int j = 0;
-
- debug("[I2C] i2c_doio\n");
-
-#ifdef CONFIG_SYS_I2C_UCODE_PATCH
- iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
-#endif
-
- if (state->tx_idx <= 0 && state->rx_idx <= 0) {
- debug("[I2C] No I/O is queued\n");
- return I2CERR_QUEUE_EMPTY;
- }
-
- iip->iic_rbptr = iip->iic_rbase;
- iip->iic_tbptr = iip->iic_tbase;
-
- /* Enable I2C */
- debug("[I2C] Enabling I2C...\n");
- i2c->i2c_i2mod |= 0x01;
-
- /* Begin transmission */
- i2c->i2c_i2com |= 0x80;
-
- /* Loop until transmit & receive completed */
-
- if (state->tx_idx > 0) {
- txbd = ((I2C_BD*)state->txbd) - 1;
-
- debug("[I2C] Transmitting...(txbd=0x%08lx)\n",
- (ulong)txbd);
-
- while ((txbd->status & BD_SC_READY) && (j++ < TOUT_LOOP)) {
- if (ctrlc())
- return (-1);
-
- __asm__ __volatile__("eieio");
- }
- }
-
- if ((state->rx_idx > 0) && (j < TOUT_LOOP)) {
- rxbd = ((I2C_BD*)state->rxbd) - 1;
-
- debug("[I2C] Receiving...(rxbd=0x%08lx)\n",
- (ulong)rxbd);
-
- while ((rxbd->status & BD_SC_EMPTY) && (j++ < TOUT_LOOP)) {
- if (ctrlc())
- return (-1);
-
- __asm__ __volatile__("eieio");
- }
- }
-
- /* Turn off I2C */
- i2c->i2c_i2mod &= ~0x01;
-
- if (state->err_cb != NULL) {
- int n, i, b;
-
- /*
- * if we have an error callback function, look at the
- * error bits in the bd status and pass them back
- */
-
- if ((n = state->tx_idx) > 0) {
- for (i = 0; i < n; i++) {
- txbd = ((I2C_BD *) state->txbd) - (n - i);
- if ((b = txbd->status & BD_I2C_TX_ERR) != 0)
- (*state->err_cb) (I2CECB_TX_ERR | b,
- i);
- }
- }
-
- if ((n = state->rx_idx) > 0) {
- for (i = 0; i < n; i++) {
- rxbd = ((I2C_BD *) state->rxbd) - (n - i);
- if ((b = rxbd->status & BD_I2C_RX_ERR) != 0)
- (*state->err_cb) (I2CECB_RX_ERR | b,
- i);
- }
- }
-
- if (j >= TOUT_LOOP)
- (*state->err_cb) (I2CECB_TIMEOUT, 0);
- }
-
- return (j >= TOUT_LOOP) ? I2CERR_TIMEOUT : 0;
-}
-
-static int had_tx_nak;
-
-static void i2c_test_callback(int flags, int xnum)
-{
- if ((flags & I2CECB_TX_ERR) && (flags & I2CECB_TX_NAK))
- had_tx_nak = 1;
-}
-
-int i2c_probe(uchar chip)
-{
- i2c_state_t state;
- int rc;
- uchar buf[1];
-
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-
- i2c_newio(&state);
-
- state.err_cb = i2c_test_callback;
- had_tx_nak = 0;
-
- rc = i2c_receive(&state, chip, 0, I2CF_START_COND | I2CF_STOP_COND, 1,
- buf);
-
- if (rc != 0)
- return (rc);
-
- rc = i2c_doio(&state);
-
- if ((rc != 0) && (rc != I2CERR_TIMEOUT))
- return (rc);
-
- return (had_tx_nak);
-}
-
-int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
-{
- i2c_state_t state;
- uchar xaddr[4];
- int rc;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
-#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
- /*
- * EEPROM chips that implement "address overflow" are ones like
- * Catalyst 24WC04/08/16 which has 9/10/11 bits of address and the
- * extra bits end up in the "chip address" bit slots. This makes
- * a 24WC08 (1Kbyte) chip look like four 256 byte chips.
- *
- * Note that we consider the length of the address field to still
- * be one byte because the extra address bits are hidden in the
- * chip address.
- */
- chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
-#endif
-
- i2c_newio(&state);
-
- rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen,
- &xaddr[4 - alen]);
- if (rc != 0) {
- printf("i2c_read: i2c_send failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_receive(&state, chip, 0, I2CF_STOP_COND, len, buffer);
- if (rc != 0) {
- printf("i2c_read: i2c_receive failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_doio(&state);
- if (rc != 0) {
- printf("i2c_read: i2c_doio failed (%d)\n", rc);
- return 1;
- }
- return 0;
-}
-
-int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
-{
- i2c_state_t state;
- uchar xaddr[4];
- int rc;
-
- xaddr[0] = (addr >> 24) & 0xFF;
- xaddr[1] = (addr >> 16) & 0xFF;
- xaddr[2] = (addr >> 8) & 0xFF;
- xaddr[3] = addr & 0xFF;
-
-#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
- /*
- * EEPROM chips that implement "address overflow" are ones like
- * Catalyst 24WC04/08/16 which has 9/10/11 bits of address and the
- * extra bits end up in the "chip address" bit slots. This makes
- * a 24WC08 (1Kbyte) chip look like four 256 byte chips.
- *
- * Note that we consider the length of the address field to still
- * be one byte because the extra address bits are hidden in the
- * chip address.
- */
- chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
-#endif
-
- i2c_newio(&state);
-
- rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen,
- &xaddr[4 - alen]);
- if (rc != 0) {
- printf("i2c_write: first i2c_send failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_send(&state, 0, 0, I2CF_STOP_COND, len, buffer);
- if (rc != 0) {
- printf("i2c_write: second i2c_send failed (%d)\n", rc);
- return 1;
- }
-
- rc = i2c_doio(&state);
- if (rc != 0) {
- printf("i2c_write: i2c_doio failed (%d)\n", rc);
- return 1;
- }
- return 0;
-}
-
-#endif /* CONFIG_HARD_I2C */
int board_late_init(void)
{
- u8 mac[6];
-
- /* Read Mac Address and set*/
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
- i2c_set_bus_num(CONFIG_SYS_I2C_MODULE);
-
- /* Read MAC address */
- i2c_read(0x50, 0x0, 0, mac, 6);
-
- if (is_valid_ethaddr(mac))
- eth_setenv_enetaddr("ethaddr", mac);
+ printf("Cannot use I2C to get MAC address\n");
return 0;
}
at91sam9x5ek_nand_hw_init();
#endif
-#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI)
+#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI_HCD)
at91_uhp_hw_init();
#endif
#ifdef CONFIG_LCD
*/
static void read_hw_id(hw_id_t hw_id)
{
- int i;
- for (i = 0; i < HW_ID_ELEM_COUNT; ++i)
- if (i2c_read(CONFIG_SYS_I2C_EEPROM,
- hw_id_format[i].offset,
- 2,
- (uchar *)&hw_id[i][0],
- hw_id_format[i].length) != 0)
- printf("ERROR: can't read HW ID from EEPROM\n");
+ printf("ERROR: can't read HW ID from EEPROM\n");
}
strcat(buf, tmp);
}
-
+#if defined(CONFIG_SYS_I2C_SOFT)
/*
* Compose string with hostname.
* buf is assumed to have enough space, and be null-terminated.
*p = tolower(*p);
}
-
+#endif
#ifdef CONFIG_OF_BOARD_SETUP
/*
hw_id_t hw_id_tmp;
char module_name_tmp[MODULE_NAME_MAXLEN] = "";
- /*
- * We need I2C to access HW ID data from EEPROM, so we call i2c_init()
- * here despite the fact that it will be called again later on. We
- * also use a little trick to silence I2C-related output.
- */
- gd->flags |= GD_FLG_SILENT;
- i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
- gd->flags &= ~GD_FLG_SILENT;
-
read_hw_id(hw_id_tmp);
identify_module(hw_id_tmp); /* this sets gd->board_type */
compose_module_name(hw_id_tmp, module_name_tmp);
#ifdef CONFIG_MISC_INIT_R
int misc_init_r(void)
{
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
+#if defined(CONFIG_SYS_I2C_SOFT)
uchar buf[6];
char str[18];
char hostname[MODULE_NAME_MAXLEN];
" device at address %02X:%04X\n", CONFIG_SYS_I2C_EEPROM,
CONFIG_MAC_OFFSET);
}
-#endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) */
- if (!getenv("ethaddr"))
- printf(LOG_PREFIX "MAC address not set, networking is not "
- "operational\n");
-
- /* set the hostname appropriate to the module we're running on */
hostname[0] = 0x00;
+ /* set the hostname appropriate to the module we're running on */
compose_hostname(hw_id, hostname);
setenv("hostname", hostname);
+#endif /* defined(CONFIG_SYS_I2C_SOFT) */
+ if (!getenv("ethaddr"))
+ printf(LOG_PREFIX "MAC address not set, networking is not "
+ "operational\n");
+
return 0;
}
#endif /* CONFIG_MISC_INIT_R */
#ifdef CONFIG_CMD_BSP
-static int do_i2c_test(char * const argv[])
-{
- unsigned char temp, temp1;
-
- printf("Starting I2C Test\n"
- "Please set Jumper:\nI2C SDA 2-3\nI2C SCL 2-3\n\n"
- "Please press any key to start\n\n");
- getc();
-
- temp = 0xf0; /* set io 0-4 as output */
- i2c_write(CONFIG_SYS_I2C_IO, 3, 1, (uchar *)&temp, 1);
-
- printf("Press I2C4-7. LED I2C0-3 should have the same state\n\n"
- "Press any key to stop\n\n");
-
- while (!tstc()) {
- i2c_read(CONFIG_SYS_I2C_IO, 0, 1, (uchar *)&temp, 1);
- temp1 = (temp >> 4) & 0x03;
- temp1 |= (temp >> 3) & 0x08; /* S302 -> LED303 */
- temp1 |= (temp >> 5) & 0x04; /* S303 -> LED302 */
- temp = temp1;
- i2c_write(CONFIG_SYS_I2C_IO, 1, 1, (uchar *)&temp, 1);
- }
- getc();
-
- return 0;
-}
-
static int do_usb_test(char * const argv[])
{
int i;
switch (argc) {
case 2:
- if (strncmp(argv[1], "i2c", 3) == 0)
- rcode = do_i2c_test(argv);
- else if (strncmp(argv[1], "led", 3) == 0)
+ if (strncmp(argv[1], "led", 3) == 0)
rcode = do_led_test(argv);
else if (strncmp(argv[1], "usb", 3) == 0)
rcode = do_usb_test(argv);
}
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[1] = OMAP_EHCI_PORT_MODE_HSIC,
{
u32 tmp;
- /* we use I2C-2 for on-board eeprom */
- i2c_set_bus_num(2);
-
tmp = in_be32((u32*)CONFIG_SYS_ARIA_FPGA_BASE);
printf("FPGA: %u-%u.%u.%u\n",
(tmp & 0xFF000000) >> 24,
int eeprom_write_enable(unsigned dev_addr, int state)
{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
-
- if (dev_addr != CONFIG_SYS_I2C_EEPROM_ADDR)
- return -1;
-
- if (state == 0)
- setbits_be32(&im->gpio.gpdat, 0x00100000);
- else
- clrbits_be32(&im->gpio.gpdat, 0x00100000);
-
- return 0;
+ return -ENOSYS;
}
int board_early_init_f(void)
CONFIG_MCFPIT -- define to use PIT timer
CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
-CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
CONFIG_MCFPIT -- define to use PIT timer
CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
-CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
CONFIG_MCFPIT -- define to use PIT timer
CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
-CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
CONFIG_MCFPIT -- define to use PIT timer
CONFIG_SYS_FSL_I2C -- define to use FSL common I2C driver
-CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
CONFIG_SLTTMR -- define to use SLT timer
CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
-CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
int misc_init_r(void)
{
- u8 tmp_val;
-
- /* Using this for DIU init before the driver in linux takes over
- * Enable the TFP410 Encoder (I2C address 0x38)
- */
-
- i2c_set_bus_num(2);
- tmp_val = 0xBF;
- i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
- /* Verify if enabled */
- tmp_val = 0;
- i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
- debug("DVI Encoder Read: 0x%02x\n", tmp_val);
-
- tmp_val = 0x10;
- i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
- /* Verify if enabled */
- tmp_val = 0;
- i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
- debug("DVI Encoder Read: 0x%02x\n", tmp_val);
-
return 0;
}
static void setup_net_chip(void);
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/arch/ehci.h>
#include <asm/ehci-omap.h>
return rc;
}
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
#include <asm/arch/clock.h>
#include <errno.h>
#include <i2c.h>
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/ehci-omap.h>
#endif
/* Address of the framebuffer in RAM. */
#define FB_START_ADDRESS 0x88000000
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
#include <i2c.h>
#endif
-static int eeprom_diag;
static int mac_diag;
static int gpio_diag;
#define HW_COMP_MAINCPU 2
static struct eeprom_layout eeprom_content;
-static int eeprom_was_read; /* has_been_read */
static int eeprom_is_valid;
static int eeprom_version;
static int read_eeprom(void)
{
- int eeprom_datalen;
- int ret;
-
- if (eeprom_was_read)
- return 0;
-
- eeprom_is_valid = 0;
- ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
- CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
- (uchar *)&eeprom_content, sizeof(eeprom_content));
- if (eeprom_diag) {
- printf("DIAG: %s() read rc[%d], size[%d]\n",
- __func__, ret, sizeof(eeprom_content));
- }
-
- if (ret != 0)
- return -1;
-
- eeprom_was_read = 1;
-
- /*
- * check validity of EEPROM content
- * (check version, length, optionally checksum)
- */
- eeprom_is_valid = 1;
- eeprom_datalen = get_eeprom_field_int(eeprom_content.len);
- eeprom_version = get_eeprom_field_int(eeprom_content.version);
-
- if (eeprom_diag) {
- printf("DIAG: %s() magic[%c%c%c] len[%d] ver[%d] type[%d]\n",
- __func__, eeprom_content.magic[0],
- eeprom_content.magic[1], eeprom_content.magic[2],
- eeprom_datalen, eeprom_version, eeprom_content.type);
- }
- if (strncmp(eeprom_content.magic, "ifm", strlen("ifm")) != 0)
- eeprom_is_valid = 0;
- if (eeprom_datalen < sizeof(struct eeprom_layout) - 5)
- eeprom_is_valid = 0;
- if ((eeprom_version != 1) && (eeprom_version != 2))
- eeprom_is_valid = 0;
- if (eeprom_content.type != HW_COMP_MAINCPU)
- eeprom_is_valid = 0;
-
- if (eeprom_diag)
- printf("DIAG: %s() valid[%d]\n", __func__, eeprom_is_valid);
-
- return ret;
+ return -ENOSYS;
}
int mac_read_from_eeprom(void)
char *s;
int want_recovery;
- /* we use bus I2C-0 for the on-board eeprom */
- i2c_set_bus_num(0);
-
/* setup GPIO directions and initial values */
gpio_configure();
{ 0, 0, 0, 0, 0, 0 }, /* PD18 */
{ 0, 0, 0, 0, 0, 0 }, /* PD17 */
{ 0, 0, 0, 0, 0, 0 }, /* PD16 */
-#if defined(CONFIG_HARD_I2C)
- { 1, 1, 1, 0, 1, 0 }, /* PD15 I2C SDA */
- { 1, 1, 1, 0, 1, 0 }, /* PD14 I2C SCL */
-#else
{ 1, 0, 0, 0, 1, 1 }, /* PD15 */
{ 1, 0, 0, 1, 1, 1 }, /* PD14 */
-#endif
{ 0, 0, 0, 0, 0, 0 }, /* PD13 */
{ 0, 0, 0, 0, 0, 0 }, /* PD12 */
{ 0, 0, 0, 0, 0, 0 }, /* PD11 */
#if defined(CONFIG_SYS_I2C_SOFT)
MPP8_GPIO, /* SDA */
MPP9_GPIO, /* SCL */
-#endif
-#if defined(CONFIG_HARD_I2C)
- MPP8_TW_SDA,
- MPP9_TW_SCK,
#endif
MPP10_UART0_TXD,
MPP11_UART0_RXD,
config SYS_CONFIG_NAME
default "omap3_logic"
+source "board/ti/common/Kconfig"
+
endif
#include <asm/mach-types.h>
#include "overo.h"
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/ehci-omap.h>
#endif
}
#endif
-#if defined(CONFIG_USB_EHCI)
+#if defined(CONFIG_USB_EHCI_HCD)
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
return omap_ehci_hcd_stop();
}
-#endif /* CONFIG_USB_EHCI */
+#endif /* CONFIG_USB_EHCI_HCD */
clrsetbits_be32(&im->gpio.gpdat, 0x01000000, 0x00040000);
#endif
-#if defined(CONFIG_HARD_I2C)
- if (!getenv("ethaddr")) {
- uchar buf[6];
- uchar ifm_oui[3] = { 0, 2, 1, };
- int ret;
-
- /* I2C-0 for on-board eeprom */
- i2c_set_bus_num(CONFIG_SYS_I2C_EEPROM_BUS_NUM);
-
- /* Read ethaddr from EEPROM */
- ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR,
- CONFIG_SYS_I2C_EEPROM_MAC_OFFSET, 1, buf, 6);
- if (ret != 0) {
- printf("Error: Unable to read MAC from I2C"
- " EEPROM at address %02X:%02X\n",
- CONFIG_SYS_I2C_EEPROM_ADDR,
- CONFIG_SYS_I2C_EEPROM_MAC_OFFSET);
- return 1;
- }
-
- /* Owned by IFM ? */
- if (memcmp(buf, ifm_oui, sizeof(ifm_oui))) {
- printf("Illegal MAC address in EEPROM: %pM\n", buf);
- return 1;
- }
-
- eth_setenv_enetaddr("ethaddr", buf);
- }
-#endif /* defined(CONFIG_HARD_I2C) */
-
return 0;
}
DECLARE_GLOBAL_DATA_PTR;
-/*
- * MUSB port on OMAP3EVM Rev >= E requires extvbus programming.
- */
-u8 omap3_evm_need_extvbus(void)
-{
- u8 retval = 0;
-
- /* TODO: verify if cairo handheld platform needs extvbus programming */
-
- return retval;
-}
-
/*
* Routine: board_init
* Description: Early hardware init.
int board_late_init(void)
{
- u8 mac[6];
-
- /* Read Mac Address and set*/
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
- i2c_set_bus_num(CONFIG_SYS_I2C_MODULE);
-
- /* Read MAC address */
- i2c_read(0x50, 0x10, 0, mac, 6);
-
- if (is_valid_ethaddr(mac))
- eth_setenv_enetaddr("ethaddr", mac);
+ printf("Cannot get MAC address from I2C\n");
return 0;
}
}
#endif
-#if defined(CONFIG_USB_EHCI) && !defined(CONFIG_SPL_BUILD)
+#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD)
/* Call usb_stop() before starting the kernel */
void show_boot_progress(int val)
{
{
return omap_ehci_hcd_stop();
}
-#endif /* CONFIG_USB_EHCI */
+#endif /* CONFIG_USB_EHCI_HCD */
#include <spl.h>
#include <mmc.h>
#include <asm/gpio.h>
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/ehci-omap.h>
#endif
XR16L2751_GPMC_CONFIG6,
};
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
#include <i2c.h>
#include <spartan3.h>
#include <asm/gpio.h>
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/ehci-omap.h>
#endif
FPGA_GPMC_CONFIG6,
};
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
enable_i2c0_pin_mux();
i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
- if (ti_i2c_eeprom_am_get(-1, CONFIG_SYS_I2C_EEPROM_ADDR))
+ if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
+ CONFIG_EEPROM_CHIP_ADDRESS))
printf("ti_i2c_eeprom_init failed\n");
}
#endif
#ifdef CONFIG_TI_I2C_BOARD_DETECT
void do_board_detect(void)
{
- if (ti_i2c_eeprom_am_get(-1, CONFIG_SYS_I2C_EEPROM_ADDR))
+ if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
+ CONFIG_EEPROM_CHIP_ADDRESS))
printf("ti_i2c_eeprom_init failed\n");
}
#endif
#include "beagle.h"
#include <command.h>
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/ehci-omap.h>
#endif
}
#endif
-#if defined(CONFIG_USB_EHCI) && !defined(CONFIG_SPL_BUILD)
+#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD)
/* Call usb_stop() before starting the kernel */
void show_boot_progress(int val)
{
return omap_ehci_hcd_stop();
}
-#endif /* CONFIG_USB_EHCI */
+#endif /* CONFIG_USB_EHCI_HCD */
#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)
int board_eth_init(bd_t *bis)
#include "mux_data.h"
-#if defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_XHCI_OMAP)
+#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_XHCI_OMAP)
#include <sata.h>
#include <usb.h>
#include <asm/gpio.h>
return 0;
}
-#if defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_XHCI_OMAP)
+#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_XHCI_OMAP)
static void enable_host_clocks(void)
{
int auxclk;
}
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[1] = OMAP_EHCI_PORT_MODE_HSIC,
#include "panda_mux_data.h"
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/arch/ehci.h>
#include <asm/ehci-omap.h>
#endif
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
static int tfp410_read_reg(int reg, uchar *buf)
{
- if (i2c_read(CONFIG_SYS_TFP410_ADDR, reg, 1, buf, 1) != 0) {
- puts ("Error reading the chip.\n");
- return 1;
- }
- return 0;
+ puts("Error reading the chip.\n");
+ return -ENOSYS;
}
static int tfp410_write_reg(int reg, uchar buf)
{
- if (i2c_write(CONFIG_SYS_TFP410_ADDR, reg, 1, &buf, 1) != 0) {
- puts ("Error writing the chip.\n");
- return 1;
- }
- return 0;
+ puts("Error writing the chip.\n");
+ return -ENOSYS;
}
typedef struct _tfp410_config {
{
volatile struct mpc5xxx_lpb *lpb =
(struct mpc5xxx_lpb *) MPC5XXX_LPB;
- int oldbus = i2c_get_bus_num();
uchar buf;
int i = 0;
- i2c_set_bus_num(CONFIG_SYS_TFP410_BUS);
-
/* check version */
if (tfp410_read_reg(TFP410_REG_DEV_ID_H, &buf) != 0)
return -1;
i++;
}
printf("TFP410 initialized.\n");
- i2c_set_bus_num(oldbus);
/* set deadcycle for cs3 to 0 */
setbits_be32(&lpb->cs_deadcycle, 0xffffcfff);
#endif
/* I2C EEPROM */
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
#if defined(CONFIG_SYS_I2C)
if (bus >= 0)
i2c_set_bus_num(bus);
-#endif
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
#endif
}
return 0;
}
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
+#if defined(CONFIG_SYS_I2C)
static int init_func_i2c(void)
{
puts("I2C: ");
/* get CPU and bus clocks according to the environment variable */
get_clocks, /* get CPU and bus clocks (etc.) */
#endif
+#if !defined(CONFIG_M68K)
timer_init, /* initialize timer */
+#endif
#if defined(CONFIG_BOARD_POSTCLK_INIT)
board_postclk_init,
#endif
misc_init_f,
#endif
INIT_FUNC_WATCHDOG_RESET
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
+#if defined(CONFIG_SYS_I2C)
init_func_i2c,
#endif
#if defined(CONFIG_HARD_SPI)
/* Initialize from environment */
load_addr = getenv_ulong("loadaddr", 16, load_addr);
-#if defined(CONFIG_SYS_EXTBDINFO)
-#if defined(CONFIG_405GP) || defined(CONFIG_405EP)
-#if defined(CONFIG_I2CFAST)
- /*
- * set bi_iic_fast for linux taking environment variable
- * "i2cfast" into account
- */
- {
- char *s = getenv("i2cfast");
- if (s && ((*s == 'y') || (*s == 'Y'))) {
- gd->bd->bi_iic_fast[0] = 1;
- gd->bd->bi_iic_fast[1] = 1;
- }
- }
-#endif /* CONFIG_I2CFAST */
-#endif /* CONFIG_405GP, CONFIG_405EP */
-#endif /* CONFIG_SYS_EXTBDINFO */
return 0;
}
uint x_mm, y_mm;
unsigned int ha, hbl, hso, hspw, hborder;
unsigned int va, vbl, vso, vspw, vborder;
+ struct edid_detailed_timing *t = (struct edid_detailed_timing *)buf;
/* Edid contains pixel clock in terms of 10KHz */
set_entry(&timing->pixelclock, (buf[0] + (buf[1] << 8)) * 10000);
set_entry(&timing->vback_porch, vbl - vso - vspw);
set_entry(&timing->vsync_len, vspw);
+ timing->flags = 0;
+ if (EDID_DETAILED_TIMING_FLAG_HSYNC_POLARITY(*t))
+ timing->flags |= DISPLAY_FLAGS_HSYNC_HIGH;
+ else
+ timing->flags |= DISPLAY_FLAGS_HSYNC_LOW;
+ if (EDID_DETAILED_TIMING_FLAG_VSYNC_POLARITY(*t))
+ timing->flags |= DISPLAY_FLAGS_VSYNC_HIGH;
+ else
+ timing->flags |= DISPLAY_FLAGS_VSYNC_LOW;
+
+ if (EDID_DETAILED_TIMING_FLAG_INTERLACED(*t))
+ timing->flags = DISPLAY_FLAGS_INTERLACED;
+
debug("Detailed mode clock %u Hz, %d mm x %d mm\n"
" %04x %04x %04x %04x hborder %x\n"
" %04x %04x %04x %04x vborder %x\n",
va + vbl, vborder);
}
+/**
+ * Check if HDMI vendor specific data block is present in CEA block
+ * @param info CEA extension block
+ * @return true if block is found
+ */
+static bool cea_is_hdmi_vsdb_present(struct edid_cea861_info *info)
+{
+ u8 end, i = 0;
+
+ /* check for end of data block */
+ end = info->dtd_offset;
+ if (end == 0)
+ end = 127;
+ if (end < 4 || end > 127)
+ return false;
+ end -= 4;
+
+ while (i < end) {
+ /* Look for vendor specific data block of appropriate size */
+ if ((EDID_CEA861_DB_TYPE(*info, i) == EDID_CEA861_DB_VENDOR) &&
+ (EDID_CEA861_DB_LEN(*info, i) >= 5)) {
+ u8 *db = &info->data[i + 1];
+ u32 oui = db[0] | (db[1] << 8) | (db[2] << 16);
+
+ if (oui == HDMI_IEEE_OUI)
+ return true;
+ }
+ i += EDID_CEA861_DB_LEN(*info, i) + 1;
+ }
+
+ return false;
+}
+
int edid_get_timing(u8 *buf, int buf_size, struct display_timing *timing,
int *panel_bits_per_colourp)
{
((edid->video_input_definition & 0x70) >> 3) + 4;
}
+ timing->hdmi_monitor = false;
+ if (edid->extension_flag && (buf_size >= EDID_EXT_SIZE)) {
+ struct edid_cea861_info *info =
+ (struct edid_cea861_info *)(buf + sizeof(*edid));
+
+ if (info->extension_tag == EDID_CEA861_EXTENSION_TAG)
+ timing->hdmi_monitor = cea_is_hdmi_vsdb_present(info);
+ }
+
return 0;
}
}
break;
#endif /* CONFIG_BMP_16BPP */
-#if defined(CONFIG_BMP_24BMP)
+#if defined(CONFIG_BMP_24BPP)
case 24:
for (i = 0; i < height; ++i) {
for (j = 0; j < width; j++) {
fb -= lcd_line_length + width * (bpix / 8);
}
break;
-#endif /* CONFIG_BMP_24BMP */
+#endif /* CONFIG_BMP_24BPP */
#if defined(CONFIG_BMP_32BPP)
case 32:
for (i = 0; i < height; ++i) {
means of transmitting U-Boot over a serial line for using in SPL,
with a checksum to ensure correctness.
+config SPL_ATF_SUPPORT
+ bool "Support ARM Trusted Firmware"
+ depends on SPL && ARM64
+ help
+ ATF(ARM Trusted Firmware) is a component for ARM arch64 which which
+ is loaded by SPL(which is considered as BL2 in ATF terminology).
+ More detail at: https://github.com/ARM-software/arm-trusted-firmware
+
+config SPL_ATF_TEXT_BASE
+ depends on SPL_ATF_SUPPORT
+ hex "ATF BL31 base address"
+ help
+ This is the base address in memory for ATF BL31 text and entry point.
+
config TPL_ENV_SUPPORT
bool "Support an environment"
depends on TPL
obj-$(CONFIG_SPL_UBI) += spl_ubi.o
obj-$(CONFIG_SPL_NET_SUPPORT) += spl_net.o
obj-$(CONFIG_SPL_MMC_SUPPORT) += spl_mmc.o
+obj-$(CONFIG_SPL_ATF_SUPPORT) += spl_atf.o
obj-$(CONFIG_SPL_USB_SUPPORT) += spl_usb.o
obj-$(CONFIG_SPL_FAT_SUPPORT) += spl_fat.o
obj-$(CONFIG_SPL_EXT_SUPPORT) += spl_ext.o
gd->malloc_ptr / 1024);
#endif
+ if (IS_ENABLED(CONFIG_SPL_ATF_SUPPORT)) {
+ debug("loaded - jumping to U-Boot via ATF BL31.\n");
+ bl31_entry();
+ }
+
debug("loaded - jumping to U-Boot...\n");
spl_board_prepare_for_boot();
jump_to_image_no_args(&spl_image);
--- /dev/null
+/*
+ * Reference to the ARM TF Project,
+ * plat/arm/common/arm_bl2_setup.c
+ * Portions copyright (c) 2013-2016, ARM Limited and Contributors. All rights
+ * reserved.
+ * Copyright (C) 2016 Rockchip Electronic Co.,Ltd
+ * Written by Kever Yang <kever.yang@rock-chips.com>
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <common.h>
+#include <atf_common.h>
+#include <errno.h>
+#include <spl.h>
+
+static struct bl2_to_bl31_params_mem bl31_params_mem;
+static struct bl31_params *bl2_to_bl31_params;
+
+/**
+ * bl2_plat_get_bl31_params() - prepare params for bl31.
+ *
+ * This function assigns a pointer to the memory that the platform has kept
+ * aside to pass platform specific and trusted firmware related information
+ * to BL31. This memory is allocated by allocating memory to
+ * bl2_to_bl31_params_mem structure which is a superset of all the
+ * structure whose information is passed to BL31
+ * NOTE: This function should be called only once and should be done
+ * before generating params to BL31
+ *
+ * @return bl31 params structure pointer
+ */
+struct bl31_params *bl2_plat_get_bl31_params(void)
+{
+ struct entry_point_info *bl33_ep_info;
+
+ /*
+ * Initialise the memory for all the arguments that needs to
+ * be passed to BL31
+ */
+ memset(&bl31_params_mem, 0, sizeof(struct bl2_to_bl31_params_mem));
+
+ /* Assign memory for TF related information */
+ bl2_to_bl31_params = &bl31_params_mem.bl31_params;
+ SET_PARAM_HEAD(bl2_to_bl31_params, ATF_PARAM_BL31, ATF_VERSION_1, 0);
+
+ /* Fill BL31 related information */
+ SET_PARAM_HEAD(bl2_to_bl31_params->bl31_image_info,
+ ATF_PARAM_IMAGE_BINARY, ATF_VERSION_1, 0);
+
+ /* Fill BL32 related information if it exists */
+#ifdef BL32_BASE
+ bl2_to_bl31_params->bl32_ep_info = &bl31_params_mem.bl32_ep_info;
+ SET_PARAM_HEAD(bl2_to_bl31_params->bl32_ep_info, ATF_PARAM_EP,
+ ATF_VERSION_1, 0);
+ bl2_to_bl31_params->bl32_image_info = &bl31_params_mem.bl32_image_info;
+ SET_PARAM_HEAD(bl2_to_bl31_params->bl32_image_info,
+ ATF_PARAM_IMAGE_BINARY, ATF_VERSION_1, 0);
+#endif /* BL32_BASE */
+
+ /* Fill BL33 related information */
+ bl2_to_bl31_params->bl33_ep_info = &bl31_params_mem.bl33_ep_info;
+ bl33_ep_info = &bl31_params_mem.bl33_ep_info;
+ SET_PARAM_HEAD(bl33_ep_info, ATF_PARAM_EP, ATF_VERSION_1,
+ ATF_EP_NON_SECURE);
+
+ /* BL33 expects to receive the primary CPU MPID (through x0) */
+ bl33_ep_info->args.arg0 = 0xffff & read_mpidr();
+ bl33_ep_info->pc = CONFIG_SYS_TEXT_BASE;
+ bl33_ep_info->spsr = SPSR_64(MODE_EL2, MODE_SP_ELX,
+ DISABLE_ALL_EXECPTIONS);
+
+ bl2_to_bl31_params->bl33_image_info = &bl31_params_mem.bl33_image_info;
+ SET_PARAM_HEAD(bl2_to_bl31_params->bl33_image_info,
+ ATF_PARAM_IMAGE_BINARY, ATF_VERSION_1, 0);
+
+ return bl2_to_bl31_params;
+}
+
+void raw_write_daif(unsigned int daif)
+{
+ __asm__ __volatile__("msr DAIF, %0\n\t" : : "r" (daif) : "memory");
+}
+
+void bl31_entry(void)
+{
+ struct bl31_params *bl31_params;
+ void (*entry)(struct bl31_params *params, void *plat_params) = NULL;
+
+ bl31_params = bl2_plat_get_bl31_params();
+ entry = (void *)CONFIG_SPL_ATF_TEXT_BASE;
+
+ raw_write_daif(SPSR_EXCEPTION_MASK);
+ dcache_disable();
+
+ entry(bl31_params, NULL);
+}
#include <logbuff.h>
#endif
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
+#if defined(CONFIG_SYS_I2C)
#include <i2c.h>
#endif
#ifdef CONFIG_SYS_I2C
i2c_init_all();
#else
-#if defined(CONFIG_HARD_I2C)
- i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-#endif
#endif
#ifdef CONFIG_DM_VIDEO
/*
trans_cmnd transport; /* transport routine */
};
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
/*
* The U-Boot EHCI driver can handle any transfer length as long as there is
* enough free heap space left, but the SCSI READ(10) and WRITE(10) commands are
CONFIG_MTD_NOR_FLASH=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n"
CONFIG_AUTOBOOT_STOP_STR="++++++++++"
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n"
CONFIG_AUTOBOOT_STOP_STR="++++++++++"
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M110\""
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M112\""
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M113\""
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n"
CONFIG_AUTOBOOT_DELAY_STR="asdfg"
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_PROMPT="ac14xx> "
CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_BAUDRATE=38400
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
# CONFIG_CMD_ENV_EXISTS is not set
# CONFIG_CMD_LOADB is not set
# CONFIG_CMD_LOADS is not set
-CONFIG_CMD_I2C=y
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_ECHO is not set
# CONFIG_CMD_ITEST is not set
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_MMC=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_UBI=y
CONFIG_MMC_MXS=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_BOARD_EARLY_INIT_F=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
# CONFIG_CMD_NET is not set
# CONFIG_CMD_NFS is not set
CONFIG_TEGRA20_SLINK=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_USB_STORAGE=y
CONFIG_SYS_WHITE_ON_BLACK=y
CONFIG_LCD=y
+CONFIG_OMAP_WATCHDOG=y
CONFIG_OF_LIBFDT=y
CONFIG_USB_STORAGE=y
CONFIG_SYS_WHITE_ON_BLACK=y
CONFIG_LCD=y
+CONFIG_OMAP_WATCHDOG=y
CONFIG_OF_LIBFDT=y
CONFIG_USB_STORAGE=y
CONFIG_SYS_WHITE_ON_BLACK=y
CONFIG_LCD=y
+CONFIG_OMAP_WATCHDOG=y
CONFIG_OF_LIBFDT=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_MAC_PARTITION=y
CONFIG_DOS_PARTITION=y
CONFIG_ISO_PARTITION=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_MAC_PARTITION=y
CONFIG_DOS_PARTITION=y
CONFIG_ISO_PARTITION=y
CONFIG_TEGRA20_SLINK=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_TEGRA114_SPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_SILENT_CONSOLE=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_SPI_FLASH_SST=y
CONFIG_SPI_FLASH_WINBOND=y
CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_KEYBOARD=y
CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
CONFIG_OF_LIBFDT=y
CONFIG_ARCH_OMAP2PLUS=y
CONFIG_OMAP54XX=y
CONFIG_TARGET_CM_T54=y
+CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC=16296
# CONFIG_SPL_NAND_SUPPORT is not set
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=3
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_ULPI_VIEWPORT=y
CONFIG_USB_ULPI=y
CONFIG_USB_STORAGE=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_FSL_DSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_DFU_NAND=y
# CONFIG_MMC is not set
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_ATMEL_USBA=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_TEGRA114_SPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_AUTOBOOT_DELAY_STR="d"
CONFIG_AUTOBOOT_STOP_STR=" "
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n"
CONFIG_AUTOBOOT_DELAY_STR=" "
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
CONFIG_AUTOBOOT_DELAY_STR="d"
CONFIG_AUTOBOOT_STOP_STR=" "
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
CONFIG_AUTOBOOT_DELAY_STR="d"
CONFIG_AUTOBOOT_STOP_STR=" "
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
# CONFIG_MMC is not set
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
# CONFIG_MMC is not set
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_G_DNL_MANUFACTURER="Siemens AG"
CONFIG_G_DNL_VENDOR_NUM=0x0908
CONFIG_G_DNL_PRODUCT_NUM=0x02d2
+CONFIG_OMAP_WATCHDOG=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_SYS_NS16550=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_DEBUG_UART_SHIFT=2
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_TEGRA114_SPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_OMAP is not set
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_G_DNL_MANUFACTURER="Siemens AG"
CONFIG_G_DNL_VENDOR_NUM=0x0908
CONFIG_G_DNL_PRODUCT_NUM=0x02d2
+CONFIG_OMAP_WATCHDOG=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
# CONFIG_MMC is not set
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_BAUDRATE=38400
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_BOARD_EARLY_INIT_F=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_SETEXPR is not set
# CONFIG_MMC is not set
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_OF_CONTROL=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_DM_VIDEO=y
CONFIG_CMD_DHRYSTONE=y
# CONFIG_MMC is not set
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_ULPI_VIEWPORT=y
CONFIG_USB_ULPI=y
CONFIG_USB_STORAGE=y
# CONFIG_MMC is not set
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
# CONFIG_MMC is not set
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_LOOPW=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_FAT=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
CONFIG_TEGRA114_SPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_BAUDRATE=38400
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_BAUDRATE=38400
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
+CONFIG_USB=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
# CONFIG_PCI is not set
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_CONSOLE_EXTRA_INFO=y
CONFIG_OF_LIBFDT=y
CONFIG_CMD_MMC=y
CONFIG_CMD_SF=y
CONFIG_CMD_SPI=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_DHCP=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_SPI_FLASH=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_ATMEL_USBA=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_DM_THERMAL=y
+CONFIG_USB=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_DM_THERMAL=y
+CONFIG_USB=y
CONFIG_OF_LIBFDT=y
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_ULPI_VIEWPORT_OMAP=y
CONFIG_USB_ULPI=y
CONFIG_USB_STORAGE=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_FAT=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_DM_VIDEO=y
CONFIG_VIDEO_TEGRA20=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b"
CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_BEDBUG=y
CONFIG_LED_STATUS=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_MAC_PARTITION=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_MAC_PARTITION=y
CONFIG_MTD_NOR_FLASH=y
# CONFIG_PCI is not set
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_ULPI_VIEWPORT_OMAP=y
CONFIG_USB_ULPI=y
CONFIG_USB_STORAGE=y
CONFIG_LED_STATUS_CMD=y
CONFIG_MMC_MXS=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_CMD_FAT=y
CONFIG_MMC_MXS=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_SST=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_SST=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_SST=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_SST=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
# CONFIG_PARTITION_UUIDS is not set
CONFIG_MTD_NOR_FLASH=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_USB=y
CONFIG_DM_USB=y
-CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_USB=y
CONFIG_DM_USB=y
-CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
# CONFIG_MMC is not set
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
# CONFIG_MMC is not set
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_TPM_TIS_INFINEON=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_DWC3=y
CONFIG_USB_DWC3_GADGET=y
CONFIG_USB_DWC3_PHY_SAMSUNG=y
CONFIG_DM_REGULATOR_MAX77686=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_DWC2_OTG=y
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_MUSB_GADGET=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_ARM=y
CONFIG_ARCH_OMAP2PLUS=y
+CONFIG_TI_COMMON_CMD_OPTIONS=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_OMAP34XX=y
CONFIG_TARGET_OMAP3_LOGIC=y
CONFIG_SPL_STACK_R_ADDR=0x82000000
CONFIG_DEFAULT_DEVICE_TREE="logicpd-torpedo-37xx-devkit"
-CONFIG_FIT=y
CONFIG_SYS_EXTRA_OPTIONS="NAND"
CONFIG_SYS_CONSOLE_INFO_QUIET=y
CONFIG_VERSION_VARIABLE=y
CONFIG_SPL_OS_BOOT=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="OMAP Logic # "
-CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMI is not set
# CONFIG_CMD_IMLS is not set
-CONFIG_CMD_ASKENV=y
# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PART=y
-CONFIG_CMD_SPI=y
-CONFIG_CMD_I2C=y
+# CONFIG_CMD_USB is not set
# CONFIG_CMD_FPGA is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
CONFIG_CMD_UBI=y
CONFIG_ISO_PARTITION=y
-CONFIG_EFI_PARTITION=y
CONFIG_OF_CONTROL=y
# CONFIG_BLK is not set
CONFIG_DM_I2C=y
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_ARCH_OMAP2PLUS=y
CONFIG_OMAP54XX=y
CONFIG_TARGET_OMAP5_UEVM=y
+CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC=16296
# CONFIG_SPL_NAND_SUPPORT is not set
CONFIG_ARMV7_LPAE=y
CONFIG_SYS_CONSOLE_INFO_QUIET=y
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_DWC3=y
CONFIG_USB_DWC3_GADGET=y
CONFIG_USB_DWC3_OMAP=y
CONFIG_SPL=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xb5
CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="U-Boot > "
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_GPIO is not set
CONFIG_ISO_PARTITION=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_ISO_PARTITION=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_ISO_PARTITION=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_IMX_THERMAL=y
CONFIG_USB=y
CONFIG_DM_USB=y
-CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_TEGRA114_SPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_TEGRA114_SPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_TEGRA114_SPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_DM_VIDEO=y
CONFIG_VIDEO_TEGRA20=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFF000000"
CONFIG_BOOTDELAY=3
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
-CONFIG_CMD_DATE=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
CONFIG_USB=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=3
CONFIG_SYS_PROMPT="uboot> "
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
-CONFIG_CMD_DATE=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
CONFIG_USB=y
# CONFIG_CONSOLE_MUX is not set
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
-CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
# CONFIG_PCI is not set
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
CONFIG_OF_LIBFDT=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
# CONFIG_MMC is not set
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_BAUDRATE=38400
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
# CONFIG_VIDEO_SW_CURSOR is not set
CONFIG_SYS_CONSOLE_BG_COL=0xff
CONFIG_SYS_CONSOLE_FG_COL=0x00
+CONFIG_OMAP_WATCHDOG=y
# CONFIG_CMD_ENV_EXISTS is not set
# CONFIG_CMD_LOADB is not set
# CONFIG_CMD_LOADS is not set
-CONFIG_CMD_I2C=y
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_ECHO is not set
# CONFIG_CMD_ITEST is not set
CONFIG_G_DNL_MANUFACTURER="Siemens AG"
CONFIG_G_DNL_VENDOR_NUM=0x0908
CONFIG_G_DNL_PRODUCT_NUM=0x02d2
+CONFIG_OMAP_WATCHDOG=y
# CONFIG_MMC is not set
CONFIG_SPI_FLASH=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
# CONFIG_MMC is not set
CONFIG_SPI_FLASH=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_CMD_FAT=y
CONFIG_MMC_MXS=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_OF_LIBFDT=y
CONFIG_CMD_FAT=y
CONFIG_MMC_MXS=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_ULPI_VIEWPORT=y
CONFIG_USB_ULPI=y
CONFIG_USB_STORAGE=y
CONFIG_ISO_PARTITION=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_BAUDRATE=38400
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_VIDEO_BRIDGE=y
CONFIG_ERRNO_STR=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_DM_VIDEO=y
CONFIG_VIDCONSOLE_AS_LCD=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+# CONFIG_USB_EHCI_HCD is not set
CONFIG_USB_STORAGE=y
CONFIG_CONSOLE_EXTRA_INFO=y
CONFIG_OF_LIBFDT=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_DM_VIDEO=y
CONFIG_VIDCONSOLE_AS_LCD=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_BAUDRATE=38400
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_OF_LIBFDT=y
CONFIG_TEGRA20_SLINK=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_DM_VIDEO=y
CONFIG_VIDEO_TEGRA20=y
CONFIG_G_DNL_MANUFACTURER="Siemens AG"
CONFIG_G_DNL_VENDOR_NUM=0x0908
CONFIG_G_DNL_PRODUCT_NUM=0x02d2
+CONFIG_OMAP_WATCHDOG=y
CONFIG_TEGRA20_SFLASH=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_MMC_OMAP_HS=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_ULPI_VIEWPORT_OMAP=y
CONFIG_USB_ULPI=y
CONFIG_USB_STORAGE=y
CONFIG_TARGET_V38B=y
CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
CONFIG_MAC_PARTITION=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_CMD_UBI=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_CMD_UBI=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_TEGRA114_SPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_ULPI_VIEWPORT=y
CONFIG_USB_ULPI=y
CONFIG_USB_STORAGE=y
CONFIG_NETDEVICES=y
CONFIG_ETH_DESIGNWARE=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_ATMEL_USBA=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_NETDEVICES=y
CONFIG_ETH_DESIGNWARE=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USE_TINY_PRINTF=y
CONFIG_OF_LIBFDT=y
CONFIG_CMD_FAT=y
CONFIG_MMC_MXS=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_GADGET=y
CONFIG_CI_UDC=y
CONFIG_OF_LIBFDT=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
+++ /dev/null
-README on how reset time on OMAPs should be calculated
-
-CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC:
-Most OMAPs' provide a way to specify the time for
-which the reset should be held low while the voltages
-and Oscillator outputs stabilize.
-
-This time is mostly board and PMIC dependent. Hence the
-boards are expected to specify a pre-computed time
-using the above option, (the details on how to compute
-the value are given below) without which a default time
-as specified by CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC
-is used.
-
-The value for CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC
-can be computed using a summation of the below 3 parameters
--1- Time taken by the Osciallator to stop and restart
--2- PMIC OTP time
--3- Voltage ramp time, which can be derived using the
-PMIC slew rate and value of voltage ramp needed.
- APQ8016
- MSM8916
+config OMAP_GPIO
+ bool "TI OMAP GPIO driver"
+ depends on ARCH_OMAP2PLUS
+ default y
+ help
+ Support GPIO controllers on the TI OMAP3/4/5 and related (such as
+ AM335x/AM43xx/AM57xx/DRA7xx/etc) families of SoCs.
+
config PM8916_GPIO
bool "Qualcomm PM8916 PMIC GPIO/keypad driver"
depends on DM_GPIO && PMIC_PM8916
break;
}
-
-#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
- /* Call board specific i2c bus reset routine AFTER the bus has been
- * initialized. Use either this callpoint or i2c_init_board;
- * which is called before i2c_init operations.
- * For details about this problem see doc/I2C_Edge_Conditions.
- */
- i2c_board_late_init();
-#endif
}
static int
set_i2c_bus_speed(chip, speed);
/* slave init, don't care */
-
-#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
- /* Call board specific i2c bus reset routine AFTER the bus has been
- * initialized. Use either this callpoint or i2c_init_board;
- * which is called before fti2c010_init operations.
- * For details about this problem see doc/I2C_Edge_Conditions.
- */
- i2c_board_late_init();
-#endif
}
/*
#define I2SR_IIF_CLEAR (0 << 1)
#endif
-#if defined(CONFIG_HARD_I2C) && !defined(CONFIG_SYS_I2C_BASE)
-#error "define CONFIG_SYS_I2C_BASE to use the mxc_i2c driver"
-#endif
-
#ifdef I2C_QUIRK_REG
static u16 i2c_clk_div[60][2] = {
{ 20, 0x00 }, { 22, 0x01 }, { 24, 0x02 }, { 26, 0x03 },
u16 stat;
writew(0xFFFF, &i2c_base->stat); /* clear current interrupts...*/
-#if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX)
+#if defined(CONFIG_OMAP34XX)
while ((stat = readw(&i2c_base->stat) & I2C_STAT_BB) && timeout--) {
#else
/* Read RAW status */
do {
udelay(waitdelay);
-#if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX)
+#if defined(CONFIG_OMAP34XX)
status = readw(&i2c_base->stat);
#else
/* Read RAW status */
/* own address */
writew(slaveadd, &i2c_base->oa);
-#if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX)
+#if defined(CONFIG_OMAP34XX)
/*
* Have to enable interrupts for OMAP2/3, these IPs don't have
* an 'irqstatus_raw' register and we shall have to poll 'stat'
config TWL4030_POWER
depends on OMAP34XX
bool "Enable driver for TI TWL4030 power management chip"
+ imply CMD_POWEROFF
---help---
The TWL4030 in a combination audio CODEC/power management with
GPIO and it is commonly used with the OMAP3 family of processors
;
serial_out(CONFIG_SYS_NS16550_IER, &com_port->ier);
-#if defined(CONFIG_OMAP) || defined(CONFIG_AM33XX) || \
- defined(CONFIG_TI81XX) || defined(CONFIG_AM43XX)
+#if defined(CONFIG_ARCH_OMAP2PLUS)
serial_out(0x7, &com_port->mdr1); /* mode select reset TL16C750*/
#endif
serial_out(UART_MCRVAL, &com_port->mcr);
serial_out(ns16550_getfcr(com_port), &com_port->fcr);
if (baud_divisor != -1)
NS16550_setbrg(com_port, baud_divisor);
-#if defined(CONFIG_OMAP) || \
- defined(CONFIG_AM33XX) || defined(CONFIG_SOC_DA8XX) || \
- defined(CONFIG_TI81XX) || defined(CONFIG_AM43XX)
-
+#if defined(CONFIG_ARCH_OMAP2PLUS) || defined(CONFIG_SOC_DA8XX)
/* /16 is proper to hit 115200 with 48MHz */
serial_out(0, &com_port->mdr1);
-#endif /* CONFIG_OMAP */
+#endif
#if defined(CONFIG_SOC_KEYSTONE)
serial_out(UART_REG_VAL_PWREMU_MGMT_UART_ENABLE, &com_port->regC);
#endif
priv->freq = max_hz;
priv->mode = mode;
priv->wordlen = priv->slave.wordlen;
-#ifdef CONFIG_OMAP3_SPI_D0_D1_SWAPPED
+#if 0
+ /* Please migrate to DM_SPI support for this feature. */
priv->pin_dir = MCSPI_PINDIR_D0_OUT_D1_IN;
#endif
config USB_EHCI_HCD
bool "EHCI HCD (USB 2.0) support"
+ default y if ARCH_MX5 || ARCH_MX6
select USB_HOST
---help---
The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
You may want to read <file:Documentation/usb/ehci.txt>.
-config USB_EHCI
- bool
- default USB_EHCI_HCD
- ---help---
- TODO: rename after most boards switch to Kconfig
-
if USB_EHCI_HCD
config USB_EHCI_ATMEL
Enables support for the on-chip EHCI controller on Atmel chips.
config USB_EHCI_MARVELL
- bool "Support for MVEBU (AXP / A38x) on-chip EHCI USB controller"
- depends on ARCH_MVEBU
+ bool "Support for Marvell on-chip EHCI USB controller"
+ depends on ARCH_MVEBU || KIRKWOOD || ORION5X
default y
---help---
Enables support for the on-chip EHCI controller on MVEBU SoCs.
---help---
Enables support for the on-chip EHCI controller on i.MX7 SoCs.
+config USB_EHCI_OMAP
+ bool "Support for OMAP3+ on-chip EHCI USB controller"
+ depends on ARCH_OMAP2PLUS
+ default y
+ ---help---
+ Enables support for the on-chip EHCI controller on OMAP3 and later
+ SoCs.
+
if USB_EHCI_MX7
config MXC_USB_OTG_HACTIVE
obj-$(CONFIG_USB_OHCI_GENERIC) += ohci-generic.o
# echi
-obj-$(CONFIG_USB_EHCI) += ehci-hcd.o
+obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o
obj-$(CONFIG_USB_EHCI_ARMADA100) += ehci-armada100.o utmi-armada100.o
obj-$(CONFIG_USB_EHCI_ATMEL) += ehci-atmel.o
ifdef CONFIG_MPC512X
#define CONFIG_SOC_OMAP3430
#endif
-#ifdef CONFIG_OMAP4430
+#ifdef CONFIG_OMAP44XX
#define CONFIG_ARCH_OMAP4
#endif
twl6030_usb_device_settings();
#endif
-#ifdef CONFIG_OMAP4430
+#ifdef CONFIG_OMAP44XX
u32 *usbotghs_control = (u32 *)((*ctrl)->control_usbotghs_ctrl);
*usbotghs_control = USBOTGHS_CONTROL_AVALID |
USBOTGHS_CONTROL_VBUSVALID | USBOTGHS_CONTROL_IDDIG;
#define OMAP3_OTG_SYSSTATUS_RESETDONE 0x0001
/* OMAP4430 has an internal PHY, use it */
-#ifdef CONFIG_OMAP4430
+#ifdef CONFIG_OMAP44XX
#define OMAP3_OTG_INTERFSEL_OMAP 0x0000
#else
#define OMAP3_OTG_INTERFSEL_OMAP 0x0001
stdby &= ~OMAP3_OTG_FORCESTDBY_STANDBY;
writel(stdby, &otg->forcestdby);
-#ifdef CONFIG_OMAP3_EVM
+#ifdef CONFIG_TARGET_OMAP3_EVM
musb_cfg.extvbus = omap3_evm_need_extvbus();
#endif
-#ifdef CONFIG_OMAP4430
+#ifdef CONFIG_OMAP44XX
u32 *usbotghs_control =
(u32 *)((*ctrl)->control_usbotghs_ctrl);
*usbotghs_control = 0x15;
int musb_platform_init(void);
-#ifdef CONFIG_OMAP3_EVM
+#ifdef CONFIG_TARGET_OMAP3_EVM
extern u8 omap3_evm_need_extvbus(void);
#endif
CONFIG option. See the README for details. Drives which have been
converted to driver model will instead used CONFIG_DM_VIDEO.
+config VIDEO_DW_HDMI
+ bool
+ help
+ Enables the common driver code for the Designware HDMI TX
+ block found in SoCs from various vendors.
+ As this does not provide any functionality by itself (but
+ rather requires a SoC-specific glue driver to call it), it
+ can not be enabled from the configuration menu.
+
endmenu
obj-$(CONFIG_FORMIKE) += formike.o
obj-$(CONFIG_LG4573) += lg4573.o
obj-$(CONFIG_AM335X_LCD) += am335x-fb.o
+obj-$(CONFIG_VIDEO_DW_HDMI) += dw_hdmi.o
obj-${CONFIG_VIDEO_TEGRA124} += tegra124/
obj-${CONFIG_EXYNOS_FB} += exynos/
HDMI_FC_INVIDCONF_DE_IN_POLARITY_ACTIVE_HIGH :
HDMI_FC_INVIDCONF_DE_IN_POLARITY_ACTIVE_LOW);
- /*
- * TODO(sjg@chromium.org>: Need to check for HDMI / DVI
- * inv_val |= (edid->hdmi_monitor_detected ?
- * HDMI_FC_INVIDCONF_DVI_MODEZ_HDMI_MODE :
- * HDMI_FC_INVIDCONF_DVI_MODEZ_DVI_MODE);
- */
- inv_val |= HDMI_FC_INVIDCONF_DVI_MODEZ_HDMI_MODE;
+ inv_val |= (edid->hdmi_monitor ?
+ HDMI_FC_INVIDCONF_DVI_MODEZ_HDMI_MODE :
+ HDMI_FC_INVIDCONF_DVI_MODEZ_DVI_MODE);
inv_val |= HDMI_FC_INVIDCONF_R_V_BLANK_IN_OSC_ACTIVE_LOW;
}
/* hdmi initialization step b.4 */
-static void hdmi_enable_video_path(struct dw_hdmi *hdmi)
+static void hdmi_enable_video_path(struct dw_hdmi *hdmi, bool audio)
{
uint clkdis;
clkdis &= ~HDMI_MC_CLKDIS_TMDSCLK_DISABLE;
hdmi_write(hdmi, clkdis, HDMI_MC_CLKDIS);
- clkdis &= ~HDMI_MC_CLKDIS_AUDCLK_DISABLE;
- hdmi_write(hdmi, clkdis, HDMI_MC_CLKDIS);
+ if (audio) {
+ clkdis &= ~HDMI_MC_CLKDIS_AUDCLK_DISABLE;
+ hdmi_write(hdmi, clkdis, HDMI_MC_CLKDIS);
+ }
}
/* workaround to clear the overflow condition */
{
int ret;
- debug("hdmi, mode info : clock %d hdis %d vdis %d\n",
+ debug("%s, mode info : clock %d hdis %d vdis %d\n",
+ edid->hdmi_monitor ? "hdmi" : "dvi",
edid->pixelclock.typ, edid->hactive.typ, edid->vactive.typ);
hdmi_av_composer(hdmi, edid);
if (ret)
return ret;
- hdmi_enable_video_path(hdmi);
+ hdmi_enable_video_path(hdmi, edid->hdmi_monitor);
- hdmi_audio_fifo_reset(hdmi);
- hdmi_audio_set_format(hdmi);
- hdmi_audio_set_samplerate(hdmi, edid->pixelclock.typ);
+ if (edid->hdmi_monitor) {
+ hdmi_audio_fifo_reset(hdmi);
+ hdmi_audio_set_format(hdmi);
+ hdmi_audio_set_samplerate(hdmi, edid->pixelclock.typ);
+ }
hdmi_video_packetize(hdmi);
hdmi_video_sample(hdmi);
config DISPLAY_ROCKCHIP_HDMI
bool "HDMI port"
+ select VIDEO_DW_HDMI
depends on VIDEO_ROCKCHIP
help
This enables High-Definition Multimedia Interface display support.
obj-y += rk_vop.o
obj-$(CONFIG_DISPLAY_ROCKCHIP_EDP) += rk_edp.o
obj-$(CONFIG_DISPLAY_ROCKCHIP_LVDS) += rk_lvds.o
-obj-$(CONFIG_DISPLAY_ROCKCHIP_HDMI) += rk_hdmi.o ../dw_hdmi.o
+obj-$(CONFIG_DISPLAY_ROCKCHIP_HDMI) += rk_hdmi.o
obj-$(CONFIG_DISPLAY_ROCKCHIP_MIPI) += rk_mipi.o
endif
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(CONFIG_VIDEO_SUNXI) += sunxi_display.o lcdc.o ../videomodes.o
+obj-$(CONFIG_VIDEO_SUNXI) += sunxi_display.o lcdc.o tve.o ../videomodes.o
obj-$(CONFIG_VIDEO_DE2) += sunxi_de2.o sunxi_dw_hdmi.o lcdc.o ../dw_hdmi.o
#include <asm/arch/gpio.h>
#include <asm/arch/lcdc.h>
#include <asm/arch/pwm.h>
+#include <asm/arch/tve.h>
#include <asm/global_data.h>
#include <asm/gpio.h>
#include <asm/io.h>
switch (sunxi_display.monitor) {
case sunxi_monitor_vga:
- writel(SUNXI_TVE_GCTRL_DAC_INPUT(0, 1) |
- SUNXI_TVE_GCTRL_DAC_INPUT(1, 2) |
- SUNXI_TVE_GCTRL_DAC_INPUT(2, 3), &tve->gctrl);
- writel(SUNXI_TVE_CFG0_VGA, &tve->cfg0);
- writel(SUNXI_TVE_DAC_CFG0_VGA, &tve->dac_cfg0);
- writel(SUNXI_TVE_UNKNOWN1_VGA, &tve->unknown1);
+ tvencoder_mode_set(tve, tve_mode_vga);
break;
case sunxi_monitor_composite_pal_nc:
- writel(SUNXI_TVE_CHROMA_FREQ_PAL_NC, &tve->chroma_freq);
- /* Fall through */
+ tvencoder_mode_set(tve, tve_mode_composite_pal_nc);
+ break;
case sunxi_monitor_composite_pal:
- writel(SUNXI_TVE_GCTRL_DAC_INPUT(0, 1) |
- SUNXI_TVE_GCTRL_DAC_INPUT(1, 2) |
- SUNXI_TVE_GCTRL_DAC_INPUT(2, 3) |
- SUNXI_TVE_GCTRL_DAC_INPUT(3, 4), &tve->gctrl);
- writel(SUNXI_TVE_CFG0_PAL, &tve->cfg0);
- writel(SUNXI_TVE_DAC_CFG0_COMPOSITE, &tve->dac_cfg0);
- writel(SUNXI_TVE_FILTER_COMPOSITE, &tve->filter);
- writel(SUNXI_TVE_PORCH_NUM_PAL, &tve->porch_num);
- writel(SUNXI_TVE_LINE_NUM_PAL, &tve->line_num);
- writel(SUNXI_TVE_BLANK_BLACK_LEVEL_PAL, &tve->blank_black_level);
- writel(SUNXI_TVE_UNKNOWN1_COMPOSITE, &tve->unknown1);
- writel(SUNXI_TVE_CBR_LEVEL_PAL, &tve->cbr_level);
- writel(SUNXI_TVE_BURST_WIDTH_COMPOSITE, &tve->burst_width);
- writel(SUNXI_TVE_UNKNOWN2_PAL, &tve->unknown2);
- writel(SUNXI_TVE_ACTIVE_NUM_COMPOSITE, &tve->active_num);
- writel(SUNXI_TVE_CHROMA_BW_GAIN_COMP, &tve->chroma_bw_gain);
- writel(SUNXI_TVE_NOTCH_WIDTH_COMPOSITE, &tve->notch_width);
- writel(SUNXI_TVE_RESYNC_NUM_PAL, &tve->resync_num);
- writel(SUNXI_TVE_SLAVE_PARA_COMPOSITE, &tve->slave_para);
+ tvencoder_mode_set(tve, tve_mode_composite_pal);
break;
case sunxi_monitor_composite_pal_m:
- writel(SUNXI_TVE_CHROMA_FREQ_PAL_M, &tve->chroma_freq);
- writel(SUNXI_TVE_COLOR_BURST_PAL_M, &tve->color_burst);
- /* Fall through */
+ tvencoder_mode_set(tve, tve_mode_composite_pal_m);
+ break;
case sunxi_monitor_composite_ntsc:
- writel(SUNXI_TVE_GCTRL_DAC_INPUT(0, 1) |
- SUNXI_TVE_GCTRL_DAC_INPUT(1, 2) |
- SUNXI_TVE_GCTRL_DAC_INPUT(2, 3) |
- SUNXI_TVE_GCTRL_DAC_INPUT(3, 4), &tve->gctrl);
- writel(SUNXI_TVE_CFG0_NTSC, &tve->cfg0);
- writel(SUNXI_TVE_DAC_CFG0_COMPOSITE, &tve->dac_cfg0);
- writel(SUNXI_TVE_FILTER_COMPOSITE, &tve->filter);
- writel(SUNXI_TVE_PORCH_NUM_NTSC, &tve->porch_num);
- writel(SUNXI_TVE_LINE_NUM_NTSC, &tve->line_num);
- writel(SUNXI_TVE_BLANK_BLACK_LEVEL_NTSC, &tve->blank_black_level);
- writel(SUNXI_TVE_UNKNOWN1_COMPOSITE, &tve->unknown1);
- writel(SUNXI_TVE_CBR_LEVEL_NTSC, &tve->cbr_level);
- writel(SUNXI_TVE_BURST_PHASE_NTSC, &tve->burst_phase);
- writel(SUNXI_TVE_BURST_WIDTH_COMPOSITE, &tve->burst_width);
- writel(SUNXI_TVE_UNKNOWN2_NTSC, &tve->unknown2);
- writel(SUNXI_TVE_SYNC_VBI_LEVEL_NTSC, &tve->sync_vbi_level);
- writel(SUNXI_TVE_ACTIVE_NUM_COMPOSITE, &tve->active_num);
- writel(SUNXI_TVE_CHROMA_BW_GAIN_COMP, &tve->chroma_bw_gain);
- writel(SUNXI_TVE_NOTCH_WIDTH_COMPOSITE, &tve->notch_width);
- writel(SUNXI_TVE_RESYNC_NUM_NTSC, &tve->resync_num);
- writel(SUNXI_TVE_SLAVE_PARA_COMPOSITE, &tve->slave_para);
+ tvencoder_mode_set(tve, tve_mode_composite_ntsc);
break;
case sunxi_monitor_none:
case sunxi_monitor_dvi:
}
}
-static void sunxi_tvencoder_enable(void)
-{
- struct sunxi_tve_reg * const tve =
- (struct sunxi_tve_reg *)SUNXI_TVE0_BASE;
-
- setbits_le32(&tve->gctrl, SUNXI_TVE_GCTRL_ENABLE);
-}
-
#endif /* CONFIG_VIDEO_VGA || defined CONFIG_VIDEO_COMPOSITE */
static void sunxi_drc_init(void)
int __maybe_unused clk_div, clk_double;
struct sunxi_lcdc_reg * const lcdc =
(struct sunxi_lcdc_reg *)SUNXI_LCD0_BASE;
+ struct sunxi_tve_reg * __maybe_unused const tve =
+ (struct sunxi_tve_reg *)SUNXI_TVE0_BASE;
switch (sunxi_display.monitor) {
case sunxi_monitor_none:
sunxi_tvencoder_mode_set();
sunxi_composer_enable();
lcdc_enable(lcdc, sunxi_display.depth);
- sunxi_tvencoder_enable();
+ tvencoder_enable(tve);
#elif defined CONFIG_VIDEO_VGA_VIA_LCD
sunxi_composer_mode_set(mode, address);
sunxi_lcdc_tcon0_mode_set(mode, true);
sunxi_tvencoder_mode_set();
sunxi_composer_enable();
lcdc_enable(lcdc, sunxi_display.depth);
- sunxi_tvencoder_enable();
+ tvencoder_enable(tve);
#endif
break;
}
--- /dev/null
+/*
+ * TV encoder driver for Allwinner SoCs.
+ *
+ * (C) Copyright 2013-2014 Luc Verhaegen <libv@skynet.be>
+ * (C) Copyright 2014-2015 Hans de Goede <hdegoede@redhat.com>
+ * (C) Copyright 2017 Jernej Skrabec <jernej.skrabec@siol.net>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+
+#include <asm/arch/tve.h>
+#include <asm/io.h>
+
+void tvencoder_mode_set(struct sunxi_tve_reg * const tve, enum tve_mode mode)
+{
+ switch (mode) {
+ case tve_mode_vga:
+ writel(SUNXI_TVE_GCTRL_DAC_INPUT(0, 1) |
+ SUNXI_TVE_GCTRL_DAC_INPUT(1, 2) |
+ SUNXI_TVE_GCTRL_DAC_INPUT(2, 3), &tve->gctrl);
+ writel(SUNXI_TVE_CFG0_VGA, &tve->cfg0);
+ writel(SUNXI_TVE_DAC_CFG0_VGA, &tve->dac_cfg0);
+ writel(SUNXI_TVE_UNKNOWN1_VGA, &tve->unknown1);
+ break;
+ case tve_mode_composite_pal_nc:
+ writel(SUNXI_TVE_CHROMA_FREQ_PAL_NC, &tve->chroma_freq);
+ /* Fall through */
+ case tve_mode_composite_pal:
+ writel(SUNXI_TVE_GCTRL_DAC_INPUT(0, 1) |
+ SUNXI_TVE_GCTRL_DAC_INPUT(1, 2) |
+ SUNXI_TVE_GCTRL_DAC_INPUT(2, 3) |
+ SUNXI_TVE_GCTRL_DAC_INPUT(3, 4), &tve->gctrl);
+ writel(SUNXI_TVE_CFG0_PAL, &tve->cfg0);
+ writel(SUNXI_TVE_DAC_CFG0_COMPOSITE, &tve->dac_cfg0);
+ writel(SUNXI_TVE_FILTER_COMPOSITE, &tve->filter);
+ writel(SUNXI_TVE_PORCH_NUM_PAL, &tve->porch_num);
+ writel(SUNXI_TVE_LINE_NUM_PAL, &tve->line_num);
+ writel(SUNXI_TVE_BLANK_BLACK_LEVEL_PAL,
+ &tve->blank_black_level);
+ writel(SUNXI_TVE_UNKNOWN1_COMPOSITE, &tve->unknown1);
+ writel(SUNXI_TVE_CBR_LEVEL_PAL, &tve->cbr_level);
+ writel(SUNXI_TVE_BURST_WIDTH_COMPOSITE, &tve->burst_width);
+ writel(SUNXI_TVE_UNKNOWN2_PAL, &tve->unknown2);
+ writel(SUNXI_TVE_ACTIVE_NUM_COMPOSITE, &tve->active_num);
+ writel(SUNXI_TVE_CHROMA_BW_GAIN_COMP, &tve->chroma_bw_gain);
+ writel(SUNXI_TVE_NOTCH_WIDTH_COMPOSITE, &tve->notch_width);
+ writel(SUNXI_TVE_RESYNC_NUM_PAL, &tve->resync_num);
+ writel(SUNXI_TVE_SLAVE_PARA_COMPOSITE, &tve->slave_para);
+ break;
+ case tve_mode_composite_pal_m:
+ writel(SUNXI_TVE_CHROMA_FREQ_PAL_M, &tve->chroma_freq);
+ writel(SUNXI_TVE_COLOR_BURST_PAL_M, &tve->color_burst);
+ /* Fall through */
+ case tve_mode_composite_ntsc:
+ writel(SUNXI_TVE_GCTRL_DAC_INPUT(0, 1) |
+ SUNXI_TVE_GCTRL_DAC_INPUT(1, 2) |
+ SUNXI_TVE_GCTRL_DAC_INPUT(2, 3) |
+ SUNXI_TVE_GCTRL_DAC_INPUT(3, 4), &tve->gctrl);
+ writel(SUNXI_TVE_CFG0_NTSC, &tve->cfg0);
+ writel(SUNXI_TVE_DAC_CFG0_COMPOSITE, &tve->dac_cfg0);
+ writel(SUNXI_TVE_FILTER_COMPOSITE, &tve->filter);
+ writel(SUNXI_TVE_PORCH_NUM_NTSC, &tve->porch_num);
+ writel(SUNXI_TVE_LINE_NUM_NTSC, &tve->line_num);
+ writel(SUNXI_TVE_BLANK_BLACK_LEVEL_NTSC,
+ &tve->blank_black_level);
+ writel(SUNXI_TVE_UNKNOWN1_COMPOSITE, &tve->unknown1);
+ writel(SUNXI_TVE_CBR_LEVEL_NTSC, &tve->cbr_level);
+ writel(SUNXI_TVE_BURST_PHASE_NTSC, &tve->burst_phase);
+ writel(SUNXI_TVE_BURST_WIDTH_COMPOSITE, &tve->burst_width);
+ writel(SUNXI_TVE_UNKNOWN2_NTSC, &tve->unknown2);
+ writel(SUNXI_TVE_SYNC_VBI_LEVEL_NTSC, &tve->sync_vbi_level);
+ writel(SUNXI_TVE_ACTIVE_NUM_COMPOSITE, &tve->active_num);
+ writel(SUNXI_TVE_CHROMA_BW_GAIN_COMP, &tve->chroma_bw_gain);
+ writel(SUNXI_TVE_NOTCH_WIDTH_COMPOSITE, &tve->notch_width);
+ writel(SUNXI_TVE_RESYNC_NUM_NTSC, &tve->resync_num);
+ writel(SUNXI_TVE_SLAVE_PARA_COMPOSITE, &tve->slave_para);
+ break;
+ }
+}
+
+void tvencoder_enable(struct sunxi_tve_reg * const tve)
+{
+ setbits_le32(&tve->gctrl, SUNXI_TVE_GCTRL_ENABLE);
+}
}
break;
#endif /* CONFIG_BMP_16BPP */
-#if defined(CONFIG_BMP_24BMP)
+#if defined(CONFIG_BMP_24BPP)
case 24:
for (i = 0; i < height; ++i) {
for (j = 0; j < width; j++) {
fb -= priv->line_length + width * (bpix / 8);
}
break;
-#endif /* CONFIG_BMP_24BMP */
+#endif /* CONFIG_BMP_24BPP */
#if defined(CONFIG_BMP_32BPP)
case 32:
for (i = 0; i < height; ++i) {
This provides basic infrastructure to support BCM2835/2836 watchdog
hardware, with a max timeout of ~15secs.
+config OMAP_WATCHDOG
+ bool "TI OMAP watchdog driver"
+ depends on ARCH_OMAP2PLUS
+ select HW_WATCHDOG
+ default y if AM33XX
+ help
+ Say Y here to enable the OMAP3+ watchdog driver.
+
config ULP_WATCHDOG
bool "i.MX7ULP watchdog"
help
--- /dev/null
+/*
+ * This is from the ARM TF Project,
+ * Repository: https://github.com/ARM-software/arm-trusted-firmware.git
+ * File: include/common/bl_common.h
+ * Portions copyright (c) 2013-2016, ARM Limited and Contributors. All rights
+ * reserved.
+ * Copyright (C) 2016-2017 Rockchip Electronic Co.,Ltd
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#ifndef __BL_COMMON_H__
+#define __BL_COMMON_H__
+
+#define ATF_PARAM_EP 0x01
+#define ATF_PARAM_IMAGE_BINARY 0x02
+#define ATF_PARAM_BL31 0x03
+
+#define ATF_VERSION_1 0x01
+
+#define ATF_EP_SECURE 0x0
+#define ATF_EP_NON_SECURE 0x1
+
+#define SET_PARAM_HEAD(_p, _type, _ver, _attr) do { \
+ (_p)->h.type = (uint8_t)(_type); \
+ (_p)->h.version = (uint8_t)(_ver); \
+ (_p)->h.size = (uint16_t)sizeof(*_p); \
+ (_p)->h.attr = (uint32_t)(_attr) ; \
+ } while (0)
+
+#define MODE_RW_SHIFT 0x4
+#define MODE_RW_MASK 0x1
+#define MODE_RW_64 0x0
+#define MODE_RW_32 0x1
+
+#define MODE_EL_SHIFT 0x2
+#define MODE_EL_MASK 0x3
+#define MODE_EL3 0x3
+#define MODE_EL2 0x2
+#define MODE_EL1 0x1
+#define MODE_EL0 0x0
+
+#define MODE_SP_SHIFT 0x0
+#define MODE_SP_MASK 0x1
+#define MODE_SP_EL0 0x0
+#define MODE_SP_ELX 0x1
+
+#define SPSR_DAIF_SHIFT 6
+#define SPSR_DAIF_MASK 0x0f
+
+#define SPSR_64(el, sp, daif) \
+ (MODE_RW_64 << MODE_RW_SHIFT | \
+ ((el) & MODE_EL_MASK) << MODE_EL_SHIFT | \
+ ((sp) & MODE_SP_MASK) << MODE_SP_SHIFT | \
+ ((daif) & SPSR_DAIF_MASK) << SPSR_DAIF_SHIFT)
+
+#define SPSR_FIQ (1 << 6)
+#define SPSR_IRQ (1 << 7)
+#define SPSR_SERROR (1 << 8)
+#define SPSR_DEBUG (1 << 9)
+#define SPSR_EXCEPTION_MASK (SPSR_FIQ | SPSR_IRQ | SPSR_SERROR | SPSR_DEBUG)
+
+#define DAIF_FIQ_BIT (1<<0)
+#define DAIF_IRQ_BIT (1<<1)
+#define DAIF_ABT_BIT (1<<2)
+#define DAIF_DBG_BIT (1<<3)
+#define DISABLE_ALL_EXECPTIONS \
+ (DAIF_FIQ_BIT | DAIF_IRQ_BIT | DAIF_ABT_BIT | DAIF_DBG_BIT)
+
+#ifndef __ASSEMBLY__
+
+/*******************************************************************************
+ * Structure used for telling the next BL how much of a particular type of
+ * memory is available for its use and how much is already used.
+ ******************************************************************************/
+struct aapcs64_params {
+ unsigned long arg0;
+ unsigned long arg1;
+ unsigned long arg2;
+ unsigned long arg3;
+ unsigned long arg4;
+ unsigned long arg5;
+ unsigned long arg6;
+ unsigned long arg7;
+};
+
+/***************************************************************************
+ * This structure provides version information and the size of the
+ * structure, attributes for the structure it represents
+ ***************************************************************************/
+struct param_header {
+ uint8_t type; /* type of the structure */
+ uint8_t version; /* version of this structure */
+ uint16_t size; /* size of this structure in bytes */
+ uint32_t attr; /* attributes: unused bits SBZ */
+};
+
+/*****************************************************************************
+ * This structure represents the superset of information needed while
+ * switching exception levels. The only two mechanisms to do so are
+ * ERET & SMC. Security state is indicated using bit zero of header
+ * attribute
+ * NOTE: BL1 expects entrypoint followed by spsr at an offset from the start
+ * of this structure defined by the macro `ENTRY_POINT_INFO_PC_OFFSET` while
+ * processing SMC to jump to BL31.
+ *****************************************************************************/
+struct entry_point_info {
+ struct param_header h;
+ uintptr_t pc;
+ uint32_t spsr;
+ struct aapcs64_params args;
+};
+
+/*****************************************************************************
+ * Image info binary provides information from the image loader that
+ * can be used by the firmware to manage available trusted RAM.
+ * More advanced firmware image formats can provide additional
+ * information that enables optimization or greater flexibility in the
+ * common firmware code
+ *****************************************************************************/
+struct atf_image_info {
+ struct param_header h;
+ uintptr_t image_base; /* physical address of base of image */
+ uint32_t image_size; /* bytes read from image file */
+};
+
+/*****************************************************************************
+ * The image descriptor struct definition.
+ *****************************************************************************/
+struct image_desc {
+ /* Contains unique image id for the image. */
+ unsigned int image_id;
+ /*
+ * This member contains Image state information.
+ * Refer IMAGE_STATE_XXX defined above.
+ */
+ unsigned int state;
+ uint32_t copied_size; /* image size copied in blocks */
+ struct atf_image_info atf_image_info;
+ struct entry_point_info ep_info;
+};
+
+/*******************************************************************************
+ * This structure represents the superset of information that can be passed to
+ * BL31 e.g. while passing control to it from BL2. The BL32 parameters will be
+ * populated only if BL2 detects its presence. A pointer to a structure of this
+ * type should be passed in X0 to BL31's cold boot entrypoint.
+ *
+ * Use of this structure and the X0 parameter is not mandatory: the BL31
+ * platform code can use other mechanisms to provide the necessary information
+ * about BL32 and BL33 to the common and SPD code.
+ *
+ * BL31 image information is mandatory if this structure is used. If either of
+ * the optional BL32 and BL33 image information is not provided, this is
+ * indicated by the respective image_info pointers being zero.
+ ******************************************************************************/
+struct bl31_params {
+ struct param_header h;
+ struct atf_image_info *bl31_image_info;
+ struct entry_point_info *bl32_ep_info;
+ struct atf_image_info *bl32_image_info;
+ struct entry_point_info *bl33_ep_info;
+ struct atf_image_info *bl33_image_info;
+};
+
+/*******************************************************************************
+ * This structure represents the superset of information that is passed to
+ * BL31, e.g. while passing control to it from BL2, bl31_params
+ * and other platform specific params
+ ******************************************************************************/
+struct bl2_to_bl31_params_mem {
+ struct bl31_params bl31_params;
+ struct atf_image_info bl31_image_info;
+ struct atf_image_info bl32_image_info;
+ struct atf_image_info bl33_image_info;
+ struct entry_point_info bl33_ep_info;
+ struct entry_point_info bl32_ep_info;
+ struct entry_point_info bl31_ep_info;
+};
+
+#endif /*__ASSEMBLY__*/
+
+#endif /* __BL_COMMON_H__ */
void fdc_hw_init (void);
/* $(BOARD)/eeprom.c */
+#ifdef CONFIG_CMD_EEPROM
void eeprom_init (int bus);
int eeprom_read (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
+#else
+/*
+ * Some EEPROM code is depecated because it used the legacy I2C interface. Add
+ * some macros here so we don't have to touch every one of those uses
+ */
+#define eeprom_init(bus)
+#define eeprom_read(dev_addr, offset, buffer, cnt) ((void)-ENOSYS)
+#define eeprom_write(dev_addr, offset, buffer, cnt) ((void)-ENOSYS)
+#endif
/*
* Set this up regardless of board
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#define CONFIG_SHA_HW_ACCEL
#endif
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
#endif
-#define CONFIG_USB_EHCI /* USB */
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#define CONFIG_HAS_FSL_DR_USB
/* USB */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
#define CONFIG_SYS_USB_EHCI_REGS_BASE 0xFC0B0000
#define CONFIG_SYS_USB_EHCI_CPU_INIT
#endif
/* I2c */
#undef CONFIG_SYS_FSL_I2C
-#undef CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
/* I2C speed and slave address */
#define CONFIG_SYS_I2C_SPEED 80000
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_SYS_SCCR_USBDRCM 3
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_USB_PHY_TYPE "utmi"
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
/*
* Support USB
*/
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
/* Current USB implementation supports the only USB controller,
#define CONFIG_PQ_MDS_PIB 1 /* PQ MDS Platform IO Board */
#define CONFIG_HAS_FSL_DR_USB 1 /* fixup device tree for the DR USB */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_ENV_OVERWRITE
#define CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
*/
#define CONFIG_HAS_FSL_MPH_USB
#ifdef CONFIG_HAS_FSL_MPH_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
/*
* USB
*/
-#define CONFIG_USB_EHCI
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_PCI
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_PCI_EHCI_DEVICE 0
/*
* USB
*/
-#define CONFIG_USB_EHCI
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_PCI
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_PCI_EHCI_DEVICE 0
#define CONFIG_HAS_FSL_DR_USB
#if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI_HCD) \
|| defined(CONFIG_FSL_SATA)
#endif
*/
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
*/
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
#define CONFIG_HAS_FSL_MPH_USB
#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#define __T208xQDS_H
#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
-#define CONFIG_USB_EHCI
#if defined(CONFIG_ARCH_T2080)
#define CONFIG_FSL_SATA_V2
#define CONFIG_SYS_SRIO /* Enable Serial RapidIO Support */
/*
* USB
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_HAS_FSL_DR_USB
#define __T2080RDB_H
#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
-#define CONFIG_USB_EHCI
#define CONFIG_FSL_SATA_V2
/* High Level Configuration Options */
/*
* USB
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_HAS_FSL_DR_USB
/*
* USB
*/
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_HAS_FSL_DR_USB
/*
* USB
*/
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_HAS_FSL_DR_USB
#ifndef CONFIG_CAM5200
/* POST support */
#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_CPU | \
- CONFIG_SYS_POST_I2C)
+ CONFIG_SYS_POST_CPU)
#endif
#ifdef CONFIG_POST
/*
* Command line configuration.
*/
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_REGINFO
#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#ifdef CONFIG_TQM5200_REV100
-#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */
-#else
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 for all other revs */
-#endif
-
-/*
- * I2C clock frequency
- *
- * Please notice, that the resulting clock frequency could differ from the
- * configured value. This is because the I2C clock is derived from system
- * clock over a frequency divider with only a few divider values. U-Boot
- * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
- * approximation allways lies below the configured value, never above.
- */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
- * also). For other EEPROMs configuration should be verified. On Mini-FAP the
- * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
- * same configuration could be used.
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
-
-/*
- * HW-Monitor configuration on Mini-FAP
- */
-#if defined (CONFIG_MINIFAP)
-#define CONFIG_SYS_I2C_HWMON_ADDR 0x2C
-#endif
-
-/* List of I2C addresses to be verified by POST */
-#if defined (CONFIG_MINIFAP)
-#undef CONFIG_SYS_POST_I2C_ADDRS
-#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \
- CONFIG_SYS_I2C_HWMON_ADDR, \
- CONFIG_SYS_I2C_SLAVE}
-#endif
-
/*
* Flash configuration
*/
#endif
#endif
-/*
- * RTC configuration
- */
-#if defined (CONFIG_STK52XX) && !defined (CONFIG_STK52XX_REV100)
-# define CONFIG_RTC_M41T11 1
-# define CONFIG_SYS_I2C_RTC_ADDR 0x68
-# define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* because Linux uses the same base
- year */
-#else
-# define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */
-#endif
-
/*
* Miscellaneous configurable options
*/
#define CONFIG_HAS_FSL_DR_USB
#if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
/*
* Command line configuration.
*/
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_IDE
#if defined(CONFIG_PCI)
*/
#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010010x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_SYS_EEPROM_WREN 1
-#define CONFIG_SYS_EEPROM_WP GPIO_PSC2_4
-
/*
* Flash configuration
*/
#define CONFIG_CMDLINE_EDITING 1 /* command line history */
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-
-/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
/*
* IIM - IC Identification Module
*/
#undef CONFIG_FSL_IIM
-/*
- * EEPROM configuration for Atmel AT24C01:
- * 8-bit addresses, 30ms write delay, 32-Byte Page Write Mode
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 30
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
-
/*
* Ethernet configuration
*/
#define CONFIG_LOADS_ECHO 1
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
-#define CONFIG_CMD_EEPROM
#undef CONFIG_CMD_FUSE
#undef CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2
#define CONFIG_BOUNCE_BUFFER
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_STORAGE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */
/* USB */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_RMOBILE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
/*
* High Level Configuration Options
*/
-#define CONFIG_OMAP 1 /* in a TI OMAP core */
-#define CONFIG_OMAP3_AM3517CRANE 1 /* working with CRANEBOARD */
-
#define CONFIG_EMIF4 /* The chip has EMIF4 controller */
#include <asm/arch/cpu.h> /* get chip and board defs */
#ifndef __CONFIG_H
#define __CONFIG_H
-/* High Level Configuration Options */
-
-#define CONFIG_OMAP
-
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define CONFIG_EMIF4 /* The chip has EMIF4 controller */
/* Hardware drivers */
-/* OMAP GPIO configuration */
-#define CONFIG_OMAP_GPIO
-
/* NS16550 Configuration */
#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_BITBANGMII
#define CONFIG_BITBANGMII_MULTI
-/* I2C */
-#define CONFIG_SH_SH7734_I2C 1
-#define CONFIG_HARD_I2C 1
-#define CONFIG_I2C_MULTI_BUS 1
-#define CONFIG_SYS_MAX_I2C_BUS 2
-#define CONFIG_SYS_I2C_MODULE 0
-#define CONFIG_SYS_I2C_SPEED 400000 /* 400 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x50
-#define CONFIG_SH_I2C_DATA_HIGH 4
-#define CONFIG_SH_I2C_DATA_LOW 5
-#define CONFIG_SH_I2C_CLOCK 500000000
-#define CONFIG_SH_I2C_BASE0 0xFFC70000
-#define CONFIG_SH_I2C_BASE1 0xFFC71000
-
/* undef to save memory */
#define CONFIG_SYS_LONGHELP
/* Monitor Command Prompt */
#define CONFIG_SYS_MMC_ENV_PART 1
/* USB host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* PCI host support */
#define CONFIG_SYS_MMC_ENV_PART 1
/* USB host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* PCI host support */
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#endif
-/* RTC */
-#ifdef CONFIG_CMD_DATE
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51
-#endif
-
/* Boot Linux */
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_BOOTCOMMAND "run bootcmd_nand"
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-
-/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#if 0
-#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
-#endif
-
/*
* IIM - IC Identification Module
*/
#undef CONFIG_FSL_IIM
-/*
- * EEPROM configuration for Atmel AT24C32A-10TQ-2.7:
- * 16-bit addresses, 10ms write delay, 32-Byte Page Write Mode
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
-
/*
* Ethernet configuration
*/
#define CONFIG_LOADS_ECHO 1
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
-#define CONFIG_CMD_EEPROM
#undef CONFIG_CMD_FUSE
#undef CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2
#define CONFIG_RTC_M41T11
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_CMD_NAND
/*
- * define CONFIG_USB_EHCI to enable USB Hi-Speed (aka 2.0)
+ * define CONFIG_USB_EHCI_HCD to enable USB Hi-Speed (aka 2.0)
* NB: in this case, USB 1.1 devices won't be recognized.
*/
/* USB */
#ifdef CONFIG_CMD_USB
-#ifndef CONFIG_USB_EHCI
+#ifndef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_ATMEL
#define CONFIG_USB_ATMEL_CLK_SEL_UPLL
#define CONFIG_USB_OHCI_NEW
/*
* Environment settings
*/
-#define CONFIG_ENV_IS_IN_EEPROM
+#define CONFIG_ENV_IS_NOWHERE
#define CONFIG_ENV_SIZE SZ_512
#define CONFIG_ENV_OFFSET 0
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_LCD_DT_SIMPLEFB
#define LCD_BPP LCD_COLOR32
-#define CONFIG_HW_WATCHDOG
-#define CONFIG_OMAP_WATCHDOG
-
/* Bootcount using the RTC block */
#define CONFIG_SYS_BOOTCOUNT_ADDR 0x44E3E000
#define CONFIG_BOOTCOUNT_LIMIT
#define CONFIG_VIDEO_BMP_GZIP
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (1366*767*4)
-#define CONFIG_BMP_24BMP
+#define CONFIG_BMP_24BPP
#define CONFIG_BMP_32BPP
/* memory */
#define __BUR_AM335X_COMMON_H__
/* ------------------------------------------------------------------------- */
#define CONFIG_AM33XX
-#define CONFIG_OMAP
#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */
/* Timer information */
#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
#define CONFIG_SYS_I2C_OMAP24XX
-/* GPIO */
-#define CONFIG_OMAP_GPIO
/*
* Our platforms make use of SPL to initalize the hardware (primarily
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
/*
* POST support
*/
-#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU | CONFIG_SYS_POST_I2C)
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU)
#define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4)
/* List of I2C addresses to be verified by POST */
#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_SLAVE, \
"2m(kernel),27904k(rootfs)," \
"-(config)"
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */
-#define CONFIG_SYS_I2C_SPEED 40000 /* 40 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x0
-#define CONFIG_SYS_I2C_IO 0x38 /* PCA9554AD I2C I/O port address */
-#define CONFIG_SYS_I2C_EEPROM 0x53 /* I2C EEPROM device address */
-
/*
* RTC configuration
*/
/*
* High Level Configuration Options
*/
-#define CONFIG_OMAP /* in a TI OMAP core */
-#define CONFIG_OMAP_GPIO
#define CONFIG_CM_T3X /* working with CM-T35 and CM-T3730 */
#define CONFIG_SDRC /* The chip has SDRC controller */
/* USB */
#define CONFIG_USB_OMAP3
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_OMAP
#define CONFIG_USB_MUSB_UDC
#define CONFIG_TWL4030_USB
#define CONFIG_SPLASHIMAGE_GUARD
-/* GPIO banks */
-#ifdef CONFIG_LED_STATUS
-#define CONFIG_OMAP3_GPIO_6 /* GPIO186 is in GPIO bank 6 */
-#endif
-
/* Display Configuration */
-#define CONFIG_OMAP3_GPIO_2
-#define CONFIG_OMAP3_GPIO_5
#define CONFIG_VIDEO_OMAP3
#define LCD_BPP LCD_COLOR16
/*
* High Level Configuration Options
*/
-#define CONFIG_OMAP /* in a TI OMAP core */
#define CONFIG_CM_T3517 /* working with CM-T3517 */
#define CONFIG_SYS_TEXT_BASE 0x80008000
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
115200}
-#define CONFIG_OMAP_GPIO
-
/* USB */
#define CONFIG_USB_MUSB_AM35X
#ifndef CONFIG_USB_MUSB_AM35X
#define CONFIG_USB_OMAP3
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_OMAP
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 146
#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 147
#else /* !CONFIG_USB_MUSB_AM35X */
/* Status LED */
#define GREEN_LED_GPIO 186 /* CM-T3517 Green LED is GPIO186 */
-/* GPIO banks */
-#ifdef CONFIG_LED_STATUS
-#define CONFIG_OMAP3_GPIO_6 /* GPIO186 is in GPIO bank 6 */
-#endif
-
/* Display Configuration */
-#define CONFIG_OMAP3_GPIO_2
-#define CONFIG_OMAP3_GPIO_5
#define CONFIG_VIDEO_OMAP3
#define LCD_BPP LCD_COLOR16
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
/* USB UHH support options */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_OMAP
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_USB_ETHER_MCS7830
-/* Max time to hold reset on this board, see doc/README.omap-reset-time */
-#define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC 16296
-
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_I2C_TEGRA
/* USB host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
#define CONFIG_USB_MAX_CONTROLLER_COUNT 3
#define CONFIG_SYS_MMC_ENV_PART 1
/* USB host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#endif
/* USB Host Support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_VF
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
/*
* USB
*/
-#define CONFIG_USB_EHCI
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_USB_EHCI_FSL
#define CONFIG_HAS_FSL_MPH_USB
#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#define CONFIG_AT91_WANTS_COMMON_PHY
/* USB */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
/* USB DFU support */
#define CONFIG_HAS_FSL_MPH_USB
#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_EHCI_IS_TDI
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define __CONFIG_H
/* High Level Configuration Options */
-#define CONFIG_OMAP3_DEVKIT8000 1 /* working with DevKit8000 */
#define CONFIG_MACH_TYPE MACH_TYPE_DEVKIT8000
/*
/*
* Command line configuration.
*/
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_IDE
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_PCI
#define CONFIG_BOOTCOMMAND "run mtcb_start"
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1
-#define CONFIG_SYS_I2C_MODULE 1
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
-
-/*
- * RTC configuration
- */
-#if defined(CONFIG_DIGSY_REV5)
-#define CONFIG_SYS_I2C_RTC_ADDR 0x56
-#define CONFIG_RTC_RV3029
-/* Enable 5k Ohm trickle charge resistor */
-#define CONFIG_SYS_RV3029_TCR 0x20
-#else
-#define CONFIG_RTC_DS1337
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#define CONFIG_SYS_DS1339_TCR_VAL 0xAB /* diode + 4k resistor */
-#endif
-
/*
* Flash configuration
*/
#define CONFIG_FACTORYSET
-/* Watchdog */
-#define CONFIG_OMAP_WATCHDOG
-
/* Define own nand partitions */
#define CONFIG_ENV_OFFSET_REDUND 0x2E0000
#define CONFIG_ENV_SIZE_REDUND 0x2000
#endif
#if !defined(CONFIG_USB_XHCI_HCD)
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MARVELL
#define CONFIG_EHCI_IS_TDI
#endif
#define CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
/* USB UHH support options */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_OMAP
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 1
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB2.0 Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#include "tam3517-common.h"
-#undef CONFIG_USB_EHCI
-#undef CONFIG_USB_EHCI_OMAP
#undef CONFIG_USB_OMAP3
/* Our console port is port3 */
* Common USB/EHCI configuration
*/
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
-#define CONFIG_USB_EHCI_MARVELL
#define ORION5X_USB20_HOST_PORT_BASE ORION5X_USB20_PORT0_BASE
#define CONFIG_SUPPORT_VFAT
#endif /* CONFIG_CMD_USB */
#define CONFIG_SYS_I2C_SPEED 100000
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_SYS_DCACHE_OFF
#endif
-/* Watchdog */
-#define CONFIG_OMAP_WATCHDOG
-
/* Define own nand partitions */
#define CONFIG_ENV_OFFSET_REDUND 0xB80000
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_IRAM_STACK
/* USB */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_EXYNOS
#define CONFIG_USB_XHCI_EXYNOS
/* USB Configs */
#ifdef CONFIG_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */
/* USB */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_RMOBILE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_ENV_SIZE 0x4000
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_ARMADA100
#define CONFIG_EHCI_IS_TDI
#endif /* CONFIG_CMD_USB */
#define CONFIG_ARP_TIMEOUT 200UL
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_USB_ETHER_SMSC95XX
#define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sector size */
/* USB Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_TSEC2
#define CONFIG_TSEC_ENET
#define CONFIG_HARD_SPI
-#define CONFIG_HARD_I2C
/*
* NOR FLASH setup
#define OF_SOC "soc5200@f0000000"
#define OF_TBCLK (bd->bi_busfreq / 4)
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51
-
#define CONFIG_SYS_FLASH_BASE 0xFC000000
#define CONFIG_SYS_FLASH_SIZE 0x01000000
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
#endif
-#if 0
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
-#endif
-
/*
* Flash configuration
*/
#define CONFIG_SYS_L2_PL310 1
#define CONFIG_SYS_PL310_BASE 0x48242000
-/*
- * Platform
- */
-
-#define CONFIG_OMAP
-#define CONFIG_OMAP4430
-
/*
* Board
*/
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024 + CONFIG_ENV_SIZE)
-/*
- * GPIO
- */
-
-#define CONFIG_OMAP_GPIO
-
/*
* I2C
*/
#define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */
/* USB */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_RMOBILE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_SYS_TMU_CLK_DIV 4
/* USB */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_RMOBILE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 3
/* USB Configs */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_STORAGE
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
/*#define CONFIG_HAS_FSL_DR_USB*/
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
/*#define CONFIG_HAS_FSL_DR_USB*/
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
/*#define CONFIG_HAS_FSL_DR_USB*/
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
/*
* USB/EHCI
*/
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
#define CONFIG_USB_EHCI_PPC4XX /* on PPC4xx platform */
#define CONFIG_SYS_PPC4XX_USB_ADDR 0xe0000300
#define CONFIG_EHCI_MMIO_BIG_ENDIAN
/* U-Boot Commands */
#define CONFIG_FAT_WRITE
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_NAND
#define CONFIG_CMD_NAND_TRIMFFS
#define CONFIG_FEC_MXC
#endif
-/* EEPROM */
-#ifdef CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#endif
-
/* RTC */
#ifdef CONFIG_CMD_DATE
/* Use the internal RTC in the MXS chip */
* USB
*/
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX5
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
* USB
*/
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
/* USB device */
--- /dev/null
+/*
+ * (C) Copyright 2009
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __MANROLAND_MPC52XX__COMMON_H
+#define __MANROLAND_MPC52XX__COMMON_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MPC5200 1 /* MPC5200 CPU */
+
+/* ... running at 33.000000MHz */
+#define CONFIG_SYS_MPC5XXX_CLKIN 33000000
+
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
+/*
+ * Serial console configuration
+ */
+#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200,\
+ 230400 }
+
+#if (CONFIG_SYS_TEXT_BASE == 0xFFF00000) /* Boot low */
+# define CONFIG_SYS_LOWBOOT 1
+#endif
+
+/*
+ * IPB Bus clocking configuration.
+ */
+#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
+
+/*
+ * Flash configuration
+ */
+#define CONFIG_SYS_FLASH_BASE 0xFF800000
+
+#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */
+
+#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE+0x40000) /* second sector */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks
+ (= chip selects) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout [ms]*/
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout [ms]*/
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_CFI_AMD_RESET
+
+/*
+ * Environment settings
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SIZE 0x4000
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+/*
+ * Memory map
+ */
+#define CONFIG_SYS_MBAR 0xF0000000
+#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SRAM_BASE 0x80100000 /* CS 1 */
+#define CONFIG_SYS_DISPLAY_BASE 0x80600000 /* CS 3 */
+
+/* Settings for XLB = 132 MHz */
+#define SDRAM_DDR 1
+#define SDRAM_MODE 0x018D0000
+#define SDRAM_EMODE 0x40090000
+#define SDRAM_CONTROL 0x714f0f00
+#define SDRAM_CONFIG1 0x73722930
+#define SDRAM_CONFIG2 0x47770000
+#define SDRAM_TAPDELAY 0x10000000
+
+/* Use ON-Chip SRAM until RAM will be available */
+#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
+#ifdef CONFIG_POST
+/* preserve space for the post_word at end of on-chip SRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE
+#else
+#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
+#endif
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT 1
+#endif
+
+#define CONFIG_SYS_MONITOR_LEN (192 << 10)
+#define CONFIG_SYS_MALLOC_LEN (512 << 10)
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
+
+/*
+ * Ethernet configuration
+ */
+#define CONFIG_MPC5xxx_FEC 1
+#define CONFIG_MPC5xxx_FEC_MII100
+#define CONFIG_PHY_ADDR 0x00
+#define CONFIG_MII 1
+
+/*use Hardware WDT */
+#define CONFIG_HW_WATCHDOG
+
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*
+ * Various low-level settings
+ */
+#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
+#define CONFIG_SYS_HID0_FINAL HID0_ICE
+
+#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
+#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
+
+/* 8Mbit SRAM @0x80100000 */
+#define CONFIG_SYS_CS1_START CONFIG_SYS_SRAM_BASE
+
+#define CONFIG_SYS_CS_BURST 0x00000000
+#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff Supports IDE harddisk
+ *-----------------------------------------------------------------------
+ */
+
+#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+
+#define CONFIG_IDE_PREINIT 1
+
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+
+#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
+
+/* Offset for data I/O */
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
+
+/* Offset for normal register accesses */
+#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
+
+/* Offset for alternate registers */
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
+
+/* Interval between registers */
+#define CONFIG_SYS_ATA_STRIDE 4
+
+#define CONFIG_ATAPI 1
+
+#define OF_CPU "PowerPC,5200@0"
+#define OF_SOC "soc5200@f0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
+#define CONFIG_OF_IDE_FIXUP
+
+#endif /* __MANROLAND_MPC52XX__COMMON_H */
"128k@0x19C0000(swupdate-kernel-dtb.nor)"
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_STORAGE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
/*
* High Level Configuration Options
*/
-#define CONFIG_OMAP /* in a TI OMAP core */
-#define CONFIG_OMAP3_MCX /* working with mcx */
-#define CONFIG_OMAP_GPIO
#define CONFIG_MACH_TYPE MACH_TYPE_MCX
115200}
/* EHCI */
-#define CONFIG_OMAP3_GPIO_2
-#define CONFIG_OMAP3_GPIO_5
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_OMAP
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 57
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_USB_HOST_ETHER
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */
-#define CONFIG_SYS_I2C_SLAVE 0x7F /* slave address */
-
/*
* IIM - IC Identification Module
*/
#undef CONFIG_FSL_IIM
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */
-#define CONFIG_SYS_EEPROM_WREN /* Use EEPROM write protect */
-
/*
* Ethernet configuration
*/
/*
* Environment
*/
-#define CONFIG_ENV_IS_IN_EEPROM /* Store env in I2C EEPROM */
+#define CONFIG_ENV_IS_NOWHERE /* Store env in I2C EEPROM */
#define CONFIG_ENV_SIZE 0x1000
#define CONFIG_ENV_OFFSET 0x0000 /* environment starts here */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_EEPROM
#undef CONFIG_CMD_FUSE
#undef CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2
#define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sectors */
/* USB host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
* Command line configuration.
*/
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_IDE
#define CONFIG_CMD_IMMAP
#define CONFIG_CMD_JFFS2
#define CONFIG_SYS_ATA_REG_OFFSET CONFIG_SYS_ATA_DATA_OFFSET
#define CONFIG_SYS_ATA_STRIDE 4
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* select I2C module #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */
-
/*
* RTC configuration
*/
#define ENABLE_GPIO_OUT 0x00000024
#define LED_ON 0x00000010
-/*
- * Temperature sensor
- */
-#define CONFIG_DTT_LM75 1
-#define CONFIG_DTT_SENSORS { 0x49 }
-
/*
* Environment settings
*/
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#if 0
-#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
-#endif
-
/*
* IIM - IC Identification Module
*/
#undef CONFIG_FSL_IIM
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */
-
/*
* Ethernet configuration
*/
*/
#if defined(CONFIG_CMD_USB)
-#define CONFIG_USB_EHCI /* Enable EHCI Support */
#define CONFIG_USB_EHCI_FSL /* On a FSL platform */
#define CONFIG_EHCI_MMIO_BIG_ENDIAN /* With big-endian regs */
#define CONFIG_EHCI_DESC_BIG_ENDIAN
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_REGINFO
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_AUTO_COMPLETE
-#define CONFIG_OMAP3_GPIO_4
#define CONFIG_HOSTNAME mt_ventoux
/*
* Common USB/EHCI configuration
*/
#if defined(CONFIG_CMD_USB) && !defined(CONFIG_DM)
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
#define CONFIG_SUPPORT_VFAT
#endif /* CONFIG_CMD_USB */
#define CONFIG_SYS_NAND_LARGEPAGE
/* EHCI driver */
-#define CONFIG_USB_EHCI
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1
#define CONFIG_EHCI_IS_TDI
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_FEC_MXC_PHYADDR 0x1F
/* USB Configs */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX5
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_FEC_MXC_PHYADDR 0x1F
/* USB Configs */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX5
#define CONFIG_USB_STORAGE
#define CONFIG_USB_HOST_ETHER
#define CONFIG_FEC_MXC_PHYADDR 0x1F
/* USB Configs */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX5
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_IMX_VIDEO_SKIP
/* USB */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
/* USB Configs */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_MMCROOT "/dev/mmcblk0p2"
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
/* USB Configs */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
/* USB Configs */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_PHY_ATHEROS
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_PHY_ATHEROS
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
/* USB Configs */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#endif
#endif
-/* I2C */
-#ifdef CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXS
-#define CONFIG_HARD_I2C
-#ifndef CONFIG_SYS_I2C_SPEED
-#define CONFIG_SYS_I2C_SPEED 400000
-#endif
-#endif
-
/* LCD */
#ifdef CONFIG_VIDEO
#define CONFIG_VIDEO_MXS
/* USB */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MXS
#define CONFIG_EHCI_IS_TDI
#endif
* USB/EHCI
*/
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
#define CONFIG_EHCI_IS_TDI
#define CONFIG_SUPPORT_VFAT
#define CONFIG_PHY_MICREL_KSZ9021
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_USB_ETHER_MCS7830
/*
* High Level Configuration Options
*/
-
-#define CONFIG_OMAP /* in a TI OMAP core */
-#define CONFIG_OMAP3430 /* which is in a 3430 */
-#define CONFIG_OMAP3_RX51 /* working with RX51 */
#define CONFIG_SYS_L2CACHE_OFF /* pretend there is no L2 CACHE */
#define CONFIG_MACH_TYPE MACH_TYPE_NOKIA_RX51
#define CONFIG_TWL4030_LED
#define CONFIG_TWL4030_KEYPAD
-#define CONFIG_OMAP_GPIO
#define GPIO_SLIDE 71
/*
/* USB Configs */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
/*
* Supported commands
*/
-#define CONFIG_CMD_EEPROM
#ifdef CONFIG_PCI
#define CONFIG_CMD_PCI
#endif
#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration:
- *
- * O2DNT board is equiped with Ramtron FRAM device FM24CL16
- * 16 Kib Ferroelectric Nonvolatile serial RAM memory
- * organized as 2048 x 8 bits and addressable as eight I2C devices
- * 0x50 ... 0x57 each 256 bytes in size
- *
- */
-#define CONFIG_SYS_I2C_FRAM
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
/*
* There is no write delay with FRAM, write operations are performed at bus
* speed. Thus, no status polling or write delay is needed.
#define CONFIG_LIB_HW_RAND
/* USB */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_EXYNOS
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_DEFAULT_CONSOLE "console=ttySAC2,115200n8\0"
/* USB */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_EXYNOS
/* DFU */
#define CONFIG_FASTBOOT_BUF_SIZE 0x07000000
/* USB EHCI */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_OMAP
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_USB_ETHER_MCS7830
#define CONFIG_USB_ETHER_SMSC95XX
-/* GPIO banks */
-#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */
-#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */
-
/* commands to include */
#define MTDIDS_DEFAULT "nand0=nand"
/*
* High level configuration options
*/
-#define CONFIG_OMAP /* This is TI OMAP core */
-#define CONFIG_OMAP_GPIO
#define CONFIG_SDRC /* The chip has SDRC controller */
-#define CONFIG_OMAP3_EVM /* This is a OMAP3 EVM */
-
/*
* Clock related definitions
*/
#endif
#endif
-/* GPIO banks */
-#define CONFIG_OMAP3_GPIO_3 /* GPIO64 .. 95 is in GPIO bank 3 */
-#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */
-#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */
-
/* USB */
#define CONFIG_USB_MUSB_UDC 1
#define CONFIG_USB_OMAP3 1
* DM support in SPL
*/
#undef CONFIG_DM_MMC
+#undef CONFIG_DM_MMC_OPS
#undef OMAP_HSMMC_USE_GPIO
/* select serial console configuration for SPL */
/* Hardware drivers */
-/* GPIO banks */
-#define CONFIG_OMAP3_GPIO_4 /* GPIO 96..128 is in GPIO bank 4 */
-#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */
-
#define CONFIG_USB_OMAP3
/* commands to include */
#define CONFIG_TWL4030_LED
/* USB EHCI */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_OMAP
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 183
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
-/* Initialize GPIOs by default */
-#define CONFIG_OMAP3_GPIO_2 /* GPIO32..63 is in GPIO Bank 2 */
-#define CONFIG_OMAP3_GPIO_3 /* GPIO64..95 is in GPIO Bank 3 */
-#define CONFIG_OMAP3_GPIO_4 /* GPIO96..127 is in GPIO Bank 4 */
-#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO Bank 5 */
-#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO Bank 6 */
-
/* commands to include */
#ifdef CONFIG_NAND
/* TWL4030 LED */
#define CONFIG_TWL4030_LED
-/* Initialize GPIOs by default */
-#define CONFIG_OMAP3_GPIO_4 /* GPIO96..127 is in GPIO Bank 4 */
-#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO Bank 6 */
-
/*
* NS16550 Configuration
*/
#ifndef __CONFIG_H
#define __CONFIG_H
-/*
- * High Level Configuration Options
- */
-#define CONFIG_OMAP3_ZOOM1 1 /* working with Zoom MDK Rev1 */
-
#define CONFIG_NAND
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#include <asm/arch/cpu.h> /* get chip and board defs */
*/
/* USB UHH support options */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_OMAP
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 1
#define CONFIG_SYS_I2C_TCA642X_ADDR 0x22
/* USB UHH support options */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_OMAP
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONSOLEDEV "ttyO2"
-/* Max time to hold reset on this board, see doc/README.omap-reset-time */
-#define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC 16296
-
#define CONFIG_SCSI
#define CONFIG_LIBATA
#define CONFIG_SCSI_AHCI
#define CONFIG_SYS_FSL_USDHC_NUM 2
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_HAS_FSL_DR_USB
#if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
#define CONFIG_HAS_FSL_DR_USB
#if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB2.0 Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB2.0 Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB2.0 Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SYS_MMC_ENV_PART 2
/* USB Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
/*
* Command line configuration.
*/
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_PCI
#define CONFIG_PCI_IO_SIZE 0x01000000
#define CONFIG_SYS_XLB_PIPELINING 1
-/*---------------------------------------------------------------------------
- I2C configuration
----------------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*---------------------------------------------------------------------------
- EEPROM CAT24WC32 configuration
----------------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010100x */
-#define CONFIG_SYS_I2C_FACT_ADDR 0x52 /* EEPROM CAT24WC32 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
-#define CONFIG_SYS_EEPROM_SIZE 2048
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15
-
-/*---------------------------------------------------------------------------
-RTC configuration
----------------------------------------------------------------------------*/
-#define RTC
-#define CONFIG_RTC_PCF8563 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51
-
/*---------------------------------------------------------------------------
Flash configuration
---------------------------------------------------------------------------*/
Environment settings
---------------------------------------------------------------------------*/
-/* pcm030 ships with environment is EEPROM by default */
-#define CONFIG_ENV_IS_IN_EEPROM 1
+#define CONFIG_ENV_IS_NOWHERE
#define CONFIG_ENV_OFFSET 0x00 /* environment starts at the */
/*beginning of the EEPROM */
-#define CONFIG_ENV_SIZE CONFIG_SYS_EEPROM_SIZE
+#define CONFIG_ENV_SIZE 2048
#define CONFIG_ENV_OVERWRITE 1
#define CONFIG_SYS_PDM360NG_COPROC_READ_DELAY 5000
#define CONFIG_SYS_PDM360NG_COPROC_BAUDRATE 38400
-/*
- * I2C
- */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
/*
* IIM - IC Identification Module
*/
#undef CONFIG_FSL_IIM
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM addr */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* ST AT24C01 */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-Byte Write Mode */
-
-/*
- * MAC addr in EEPROM
- */
-#define CONFIG_SYS_I2C_EEPROM_BUS_NUM 0
-#define CONFIG_SYS_I2C_EEPROM_MAC_OFFSET 0x10
/*
* Enabled only to delete "ethaddr" before testing
* "ethaddr" setting from EEPROM
#define CONFIG_FEC_AN_TIMEOUT 1
#define CONFIG_HAS_ETH0
-/*
- * Configure on-board RTC
- */
-#define CONFIG_RTC_M41T62 /* use M41T00 rtc via i2c */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
-
/*
* Environment
*/
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_REGINFO
#undef CONFIG_CMD_FUSE
#define CONFIG_SUPPORT_EMMC_BOOT
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#define CONFIG_AT91_WANTS_COMMON_PHY
/* USB */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
#define CONFIG_PHYLIB
/* USB config */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_MXC_USB_PORT 1
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sectors */
/* USB host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */
/* USB */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_RMOBILE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_FACTORYSET
-/* Watchdog */
-#define CONFIG_OMAP_WATCHDOG
-
#ifndef CONFIG_SPL_BUILD
/* Use common default */
# define CONFIG_SMC911X_BASE (0x84000000)
#endif
-/* I2C */
-#define CONFIG_SH_SH7734_I2C 1
-#define CONFIG_HARD_I2C 1
-#define CONFIG_I2C_MULTI_BUS 1
-#define CONFIG_SYS_MAX_I2C_BUS 2
-#define CONFIG_SYS_I2C_MODULE 0
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x50
-#define CONFIG_SH_I2C_DATA_HIGH 4
-#define CONFIG_SH_I2C_DATA_LOW 5
-#define CONFIG_SH_I2C_CLOCK 500000000
-#define CONFIG_SH_I2C_BASE0 0xFFC70000
-#define CONFIG_SH_I2C_BASE1 0xFFC7100
-
/* undef to save memory */
#define CONFIG_SYS_LONGHELP
/* Monitor Command Prompt */
#define CONFIG_FACTORYSET
-/* Watchdog */
-#define CONFIG_OMAP_WATCHDOG
-
/* Define own nand partitions */
#define CONFIG_ENV_OFFSET_REDUND 0x2E0000
#define CONFIG_ENV_SIZE_REDUND 0x2000
#endif /* CONFIG_SPL_BUILD */
-#ifdef CONFIG_SPL_BUILD
-#undef CONFIG_HW_WATCHDOG
-#endif
-
#if defined(CONFIG_VIDEO)
#define CONFIG_VIDEO_DA8XX
#define CONFIG_SPLASH_SCREEN
#define CONFIG_PHY_MICREL
#endif
-#if 0 /* Disable until the I2C driver will be updated */
-
-/* I2C Configs */
-#define CONFIG_CMD_I2C
-#define CONFIG_HARD_I2C
-#define CONFIG_I2C_MXC
-#define CONFIG_SYS_I2C_BASE I2C0_BASE_ADDR
-#define CONFIG_SYS_I2C_SPEED 100000
-#endif
-
#if 0 /* Disable until the FLASH will be implemented */
#define CONFIG_SYS_USE_NAND
#endif
#define CONFIG_CMD_USB
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#endif
#define CONFIG_SYS_MMC_ENV_PART 2
/* USB Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
/* USB */
#ifdef CONFIG_440EPX
-
-#undef CONFIG_USB_EHCI /* OHCI by default */
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_PPC4XX
#define CONFIG_SYS_PPC4XX_USB_ADDR 0xe0000300
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_EHCI_MMIO_BIG_ENDIAN
#define CONFIG_EHCI_DESC_BIG_ENDIAN
-#else /* CONFIG_USB_EHCI */
+#else /* CONFIG_USB_EHCI_HCD */
#define CONFIG_USB_OHCI_NEW
#define CONFIG_SYS_OHCI_BE_CONTROLLER
#define __CONFIG_SIEMENS_AM33X_COMMON_H
#define CONFIG_AM33XX
-#define CONFIG_OMAP
#include <asm/arch/omap.h>
#endif
#endif
-#define CONFIG_OMAP_GPIO
-
-/* Gpio cmd support */
-
-/* Watchdog */
-#define CONFIG_HW_WATCHDOG
-
/* Reboot after 60 sec if bootcmd fails */
#define CONFIG_RESET_TO_RETRY
#define CONFIG_BOOT_RETRY_TIME 60
#define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */
/* USB */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_RMOBILE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_TFTP_TSIZE
/* USB */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
/* MMC */
#define CONFIG_ARM_ARCH_CP15_ERRATA
-/*
- * Platform
- */
-
-#define CONFIG_OMAP
-
/*
* Board
*/
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024 + CONFIG_ENV_SIZE)
-/*
- * GPIO
- */
-
-#define CONFIG_OMAP_GPIO
-#define CONFIG_OMAP3_GPIO_2
-#define CONFIG_OMAP3_GPIO_3
-#define CONFIG_OMAP3_GPIO_4
-#define CONFIG_OMAP3_GPIO_5
-#define CONFIG_OMAP3_GPIO_6
-
/*
* I2C
*/
#define CONFIG_SYS_TMU_CLK_DIV 4
/* USB */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_RMOBILE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 3
* A10 specific configuration
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_SUNXI
#endif
* A64 specific configuration
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_SUNXI
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#endif
* High Level Configuration Options
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_SUNXI
#endif
* A31 specific configuration
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_SUNXI
#endif
* A20 specific configuration
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_SUNXI
#endif
* A23 specific configuration
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_SUNXI
#endif
/*
* High Level Configuration Options
*/
-#define CONFIG_OMAP /* in a TI OMAP core */
-#define CONFIG_OMAP_GPIO
#define CONFIG_SYS_TEXT_BASE 0x80008000
/*
* DDR related
*/
-#define CONFIG_OMAP3_MICRON_DDR /* Micron DDR */
#define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)
/*
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
115200}
/* EHCI */
-#define CONFIG_OMAP3_GPIO_5
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_OMAP
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 25
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
/*
* High Level Configuration Options
*/
-#define CONFIG_OMAP /* in a TI OMAP core */
-
-#define CONFIG_OMAP_GPIO
#define CONFIG_SDRC /* Has an SDRC controller */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
-/* GPIO banks */
-#define CONFIG_OMAP3_GPIO_2 /* GPIO32 ..63 is in GPIO bank 2 */
-#define CONFIG_OMAP3_GPIO_3 /* GPIO64 ..95 is in GPIO bank 3 */
-#define CONFIG_OMAP3_GPIO_4 /* GPIO96 ..127 is in GPIO bank 4 */
-#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */
-#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */
-
/* commands to include */
#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
*/
/* USB EHCI */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_OMAP
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 162
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
/* USB */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sectors */
/* USB host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#endif
/* remove USB */
-#ifdef CONFIG_USB_EHCI
-#undef CONFIG_USB_EHCI
-#endif
#ifdef CONFIG_USB_EHCI_TEGRA
#undef CONFIG_USB_EHCI_TEGRA
#endif
#define CONFIG_FACTORYSET
-/* Watchdog */
-#define CONFIG_OMAP_WATCHDOG
-
/* Define own nand partitions */
#define CONFIG_ENV_OFFSET_REDUND 0x2E0000
#define CONFIG_ENV_SIZE_REDUND 0x2000
#define CONFIG_TI81XX
#define CONFIG_TI814X
-#define CONFIG_OMAP
#include <asm/arch/omap.h>
#define CONFIG_SYS_LOAD_ADDR 0x81000000 /* Default */
-#define CONFIG_OMAP_GPIO
-
/**
* Physical Memory Map
*/
#define CONFIG_TI81XX
#define CONFIG_TI816X
-#define CONFIG_OMAP
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_SYS_LOAD_ADDR 0x81000000 /* Default load address */
#define CONFIG_CMD_ASKENV
-#define CONFIG_OMAP_GPIO
#define CONFIG_FS_FAT
*/
#define CONFIG_SYS_BOOTCOUNT_ADDR 0x44E3E000
-/* Enable the HW watchdog, since we can use this with bootcount */
-#define CONFIG_HW_WATCHDOG
-#define CONFIG_OMAP_WATCHDOG
-
/*
* SPL related defines. The Public RAM memory map the ROM defines the
* area between 0x402F0400 and 0x4030B800 as a download area and
#ifndef __CONFIG_TI_ARMV7_OMAP_H__
#define __CONFIG_TI_ARMV7_OMAP_H__
-/* Common defines for all OMAP architecture based SoCs */
-#define CONFIG_OMAP
-
/* I2C IP block */
#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
/* SPI IP Block */
#define CONFIG_OMAP3_SPI
-/* GPIO block */
-#define CONFIG_OMAP_GPIO
-
/*
* GPMC NAND block. We support 1 device and the physical address to
* access CS0 at is 0x8000000.
#ifndef __CONFIG_TI_OMAP4_COMMON_H
#define __CONFIG_TI_OMAP4_COMMON_H
-/*
- * High Level Configuration Options
- */
-#define CONFIG_OMAP4430 1 /* which is in a 4430 */
#define CONFIG_MISC_INIT_R
#ifndef CONFIG_SYS_L2CACHE_OFF
#define CONFIG_PHY_MICREL_KSZ9021
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_MXC_USB_PORT 1
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_SMSC95XX
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#ifndef __CONFIG_H
#define __CONFIG_H
-/* High Level Configuration Options */
-#define CONFIG_OMAP /* in a TI OMAP core */
-
#define CONFIG_MACH_TYPE MACH_TYPE_TRICORDER
/*
* 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
/* Hardware drivers */
-/* GPIO support */
-#define CONFIG_OMAP_GPIO
-
-/* GPIO banks */
-#define CONFIG_OMAP3_GPIO_2 /* GPIO32..63 are in GPIO bank 2 */
-
-/* LED support */
-
/* NS16550 Configuration */
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_ENV_OFFSET (SZ_1M - CONFIG_ENV_SIZE)
/* USB Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SYS_SPL_ARGS_ADDR (PHYS_SDRAM_1 + 0x100)
#define CONFIG_SPL_BOARD_INIT
-/* gpio 55 is used as SPL_OS_BOOT_KEY */
-#define CONFIG_OMAP3_GPIO_2
-
#endif /* __CONFIG_H */
#define CONFIG_SYS_FSL_ESDHC_NUM 1
/* USB */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX5
#define CONFIG_MXC_USB_PORT 1
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
*/
#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
-
-/*
- * RTC configuration
- */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51
-
/*
* Flash configuration - use CFI driver
*/
/*
* USB/EHCI
*/
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
#define CONFIG_USB_EHCI_VCT /* on VCT platform */
#define CONFIG_EHCI_MMIO_BIG_ENDIAN
#define CONFIG_EHCI_DESC_BIG_ENDIAN
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SYS_MMC_ENV_PART 2
/* USB Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
/* USB */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#endif
#define CONFIG_PHY_ATHEROS
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
/* USB Configs */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#define CONFIG_SYS_MMC_ENV_PART 2
/* USB Host support */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_FPGA_COUNT 1
/* USB EHCI options */
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_SPEAR
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
/*-----------------------------------------------------------------------
* USB configuration
*/
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_PCI
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 12
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
/*
* USB
*/
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MMCROOT "/dev/mmcblk0p2" /* USDHC2 */
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
* USB
*/
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
#define CONFIG_USB_EHCI_MXC
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORT 1
#define EDID_SIZE 128
#define EDID_EXT_SIZE 256
+/* OUI of HDMI vendor specific data block */
+#define HDMI_IEEE_OUI 0x000c03
+
#define GET_BIT(_x, _pos) \
(((_x) >> (_pos)) & 1)
#define GET_BITS(_x, _pos_msb, _pos_lsb) \
unsigned char checksum;
} __attribute__ ((__packed__));
+enum edid_cea861_db_types {
+ EDID_CEA861_DB_AUDIO = 0x01,
+ EDID_CEA861_DB_VIDEO = 0x02,
+ EDID_CEA861_DB_VENDOR = 0x03,
+ EDID_CEA861_DB_SPEAKER = 0x04,
+};
+
struct edid_cea861_info {
unsigned char extension_tag;
#define EDID_CEA861_EXTENSION_TAG 0x02
#define EDID_CEA861_DTD_COUNT(_x) \
GET_BITS(((_x).dtd_count), 3, 0)
unsigned char data[124];
+#define EDID_CEA861_DB_TYPE(_x, offset) \
+ GET_BITS((_x).data[offset], 7, 5)
+#define EDID_CEA861_DB_LEN(_x, offset) \
+ GET_BITS((_x).data[offset], 4, 0)
} __attribute__ ((__packed__));
/**
struct timing_entry vsync_len; /* ver. sync len */
enum display_flags flags; /* display flags */
+ bool hdmi_monitor; /* is hdmi monitor? */
};
/**
#endif
void i2c_init(int speed, int slaveaddr);
void i2c_init_board(void);
-#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
-void i2c_board_late_init(void);
-#endif
#ifdef CONFIG_SYS_I2C
/*
int spl_mmc_load_image(struct spl_image_info *spl_image,
struct spl_boot_device *bootdev);
+void bl31_entry(void);
#endif
int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
int transfer_len, int interval);
-#if defined CONFIG_USB_EHCI || defined CONFIG_USB_MUSB_HOST || defined(CONFIG_DM_USB)
+#if defined CONFIG_USB_EHCI_HCD || defined CONFIG_USB_MUSB_HOST \
+ || defined(CONFIG_DM_USB)
struct int_queue *create_int_queue(struct usb_device *dev, unsigned long pipe,
int queuesize, int elementsize, void *buffer, int interval);
int destroy_int_queue(struct usb_device *dev, struct int_queue *queue);
KBUILD_CFLAGS += $(warning)
+dtc-warning-2 += $(call dtc-option,-Wnode_name_chars_strict)
+dtc-warning-2 += $(call dtc-option,-Wproperty_name_chars_strict)
+
+dtc-warning := $(dtc-warning-$(findstring 1, $(KBUILD_ENABLE_EXTRA_GCC_CHECKS)))
+dtc-warning += $(dtc-warning-$(findstring 2, $(KBUILD_ENABLE_EXTRA_GCC_CHECKS)))
+dtc-warning += $(dtc-warning-$(findstring 3, $(KBUILD_ENABLE_EXTRA_GCC_CHECKS)))
+
+DTC_FLAGS += $(dtc-warning)
+
else
# Disable noisy checks by default
DTC_FLAGS += $(call dtc-option,-Wno-unit_address_vs_reg)
+DTC_FLAGS += $(call dtc-option,-Wno-simple_bus_reg)
+DTC_FLAGS += $(call dtc-option,-Wno-unit_address_format)
+DTC_FLAGS += $(call dtc-option,-Wno-pci_bridge)
+DTC_FLAGS += $(call dtc-option,-Wno-pci_device_bus_num)
+DTC_FLAGS += $(call dtc-option,-Wno-pci_device_reg)
endif
CONFIG_BL2_OFFSET
CONFIG_BL2_SIZE
CONFIG_BMP_16BPP
-CONFIG_BMP_24BMP
CONFIG_BMP_24BPP
CONFIG_BMP_32BPP
CONFIG_BOARDDIR
CONFIG_DEFAULT
CONFIG_DEFAULT_CONSOLE
CONFIG_DEFAULT_IMMR
-CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC
CONFIG_DEFAULT_SPI_BUS
CONFIG_DEFAULT_SPI_CS
CONFIG_DEFAULT_SPI_MODE
CONFIG_H264_FREQ
CONFIG_H8300
CONFIG_HALEAKALA
-CONFIG_HARD_I2C
CONFIG_HARD_SPI
CONFIG_HASH_VERIFY
CONFIG_HAS_DATAFLASH
CONFIG_HW_WATCHDOG
CONFIG_HW_WATCHDOG_TIMEOUT_MS
CONFIG_I2C
-CONFIG_I2CFAST
CONFIG_I2C_CHIPADDRESS
CONFIG_I2C_CMD_TREE
CONFIG_I2C_ENV_EEPROM_BUS
CONFIG_OF_SPI_FLASH
CONFIG_OF_STDOUT_PATH
CONFIG_OF_SUPPORT_OLD_DEVICE_TREES
-CONFIG_OMAP
-CONFIG_OMAP3430
-CONFIG_OMAP3_AM3517CRANE
-CONFIG_OMAP3_DEVKIT8000
-CONFIG_OMAP3_EVM
-CONFIG_OMAP3_GPIO_2
-CONFIG_OMAP3_GPIO_3
-CONFIG_OMAP3_GPIO_4
-CONFIG_OMAP3_GPIO_5
-CONFIG_OMAP3_GPIO_6
-CONFIG_OMAP3_LOGIC_USE_NEW_PRODUCT_ID
-CONFIG_OMAP3_MCX
-CONFIG_OMAP3_MICRON_DDR
-CONFIG_OMAP3_RX51
-CONFIG_OMAP3_SPI_D0_D1_SWAPPED
-CONFIG_OMAP3_ZOOM1
-CONFIG_OMAP4430
CONFIG_OMAP_EHCI_PHY1_RESET_GPIO
CONFIG_OMAP_EHCI_PHY2_RESET_GPIO
CONFIG_OMAP_EHCI_PHY3_RESET_GPIO
-CONFIG_OMAP_GPIO
-CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC
CONFIG_OMAP_USB2PHY2_HOST
CONFIG_OMAP_USB3PHY1_HOST
CONFIG_OMAP_USB_PHY
-CONFIG_OMAP_VC_I2C_HS_MCODE
-CONFIG_OMAP_WATCHDOG
CONFIG_OPTREX_BW
CONFIG_ORIGEN
CONFIG_OS1_ENV_ADDR
CONFIG_SYS_I2C_BASE3
CONFIG_SYS_I2C_BASE4
CONFIG_SYS_I2C_BASE5
-CONFIG_SYS_I2C_BOARD_LATE_INIT
CONFIG_SYS_I2C_BOOT_EEPROM_ADDR
CONFIG_SYS_I2C_BUSES
CONFIG_SYS_I2C_BUS_MAX
CONFIG_USB_EHCI_MX5
CONFIG_USB_EHCI_MXC
CONFIG_USB_EHCI_MXS
-CONFIG_USB_EHCI_OMAP
CONFIG_USB_EHCI_PCI
CONFIG_USB_EHCI_PPC4XX
CONFIG_USB_EHCI_RMOBILE
projects / people / ms / u-boot.git / commitdiff
