This commit add support for 96Boards Dragonboard410C.
It is board based on APQ8016 Qualcomm SoC, complying with
96boards specification.
Features (present out of the box):
- 4x Cortex A53 (ARMv8)
- 2x USB Host port
- 1x USB Device port
- 4x LEDs
- 1x HDMI connector
- 1x uSD connector
- 3x buttons (Power, Vol+, Vol-/Reset)
- WIFI, Bluetooth with integrated antenna
- 8GiB eMMC
U-Boot boots chained with fastboot in 64-bit mode.
For detailed build instructions see readme.txt in board directory.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
fsl-ls1043a-qds-lpuart.dtb \
fsl-ls1043a-rdb.dtb
+dtb-$(CONFIG_ARCH_SNAPDRAGON) += dragonboard410c.dtb
+
dtb-$(CONFIG_MACH_SUN4I) += \
sun4i-a10-a1000.dtb \
sun4i-a10-ba10-tvbox.dtb \
--- /dev/null
+/*
+ * U-Boot addition to handle Dragonboard 410c pins
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+&pm8916_gpios {
+ usb_hub_reset_pm {
+ gpios = <&pm8916_gpios 2 0>;
+ };
+
+ usb_sw_sel_pm {
+ gpios = <&pm8916_gpios 3 0>;
+ };
+};
+
+
+&pm8916_pon {
+ key_vol_down {
+ gpios = <&pm8916_pon 1 0>;
+ };
+
+ key_power {
+ gpios = <&pm8916_pon 0 0>;
+ };
+};
--- /dev/null
+/*
+ * Qualcomm APQ8016 based Dragonboard 410C board device tree source
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/dts-v1/;
+
+#include "skeleton64.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. Dragonboard 410c";
+ compatible = "qcom,dragonboard", "qcom,apq8016-sbc";
+ qcom,msm-id = <0xce 0x0 0xf8 0x0 0xf9 0x0 0xfa 0x0 0xf7 0x0>;
+ qcom,board-id = <0x10018 0x0>;
+ #address-cells = <0x2>;
+ #size-cells = <0x2>;
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x80000000 0 0x3da00000>;
+ };
+
+ chosen {
+ stdout-path = "/soc/serial@78b0000";
+ };
+
+
+ soc {
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ ranges = <0x0 0x0 0x0 0xffffffff>;
+ compatible = "simple-bus";
+
+ clkc: qcom,gcc@1800000 {
+ compatible = "qcom,gcc-apq8016";
+ reg = <0x1800000 0x80000>;
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ };
+
+ serial@78b0000 {
+ compatible = "qcom,msm-uartdm-v1.4";
+ reg = <0x78b0000 0x200>;
+ u-boot,dm-pre-reloc;
+ clock = <&clkc 4>;
+ };
+
+ restart@4ab000 {
+ compatible = "qcom,pshold";
+ reg = <0x4ab000 0x4>;
+ };
+
+ soc_gpios: pinctrl@1000000 {
+ compatible = "qcom,apq8016-pinctrl";
+ reg = <0x1000000 0x300000>;
+ gpio-controller;
+ gpio-count = <122>;
+ gpio-bank-name="soc";
+ #gpio-cells = <1>;
+ };
+
+ ehci@78d9000 {
+ compatible = "qcom,ehci-host";
+ reg = <0x78d9000 0x400>;
+ };
+
+ sdhci@07824000 {
+ compatible = "qcom,sdhci-msm-v4";
+ reg = <0x7824900 0x11c 0x7824000 0x800>;
+ bus-width = <0x8>;
+ index = <0x0>;
+ non-removable;
+ clock = <&clkc 0>;
+ clock-frequency = <100000000>;
+ };
+
+ sdhci@07864000 {
+ compatible = "qcom,sdhci-msm-v4";
+ reg = <0x7864900 0x11c 0x7864000 0x800>;
+ index = <0x1>;
+ bus-width = <0x4>;
+ clock = <&clkc 1>;
+ clock-frequency = <200000000>;
+ };
+
+ spmi@200f000 {
+ compatible = "qcom,spmi-pmic-arb";
+ reg = <0x200f800 0x200 0x2400000 0x400000 0x2c00000 0x400000>;
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ pmic0: pm8916@0 {
+ compatible = "qcom,spmi-pmic";
+ reg = <0x0 0x1>;
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+
+ pm8916_pon: pm8916_pon@800 {
+ compatible = "qcom,pm8916-pwrkey";
+ reg = <0x800 0x96>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ pm8916_gpios: pm8916_gpios@c000 {
+ compatible = "qcom,pm8916-gpio";
+ reg = <0xc000 0x400>;
+ gpio-controller;
+ gpio-count = <4>;
+ #gpio-cells = <2>;
+ gpio-bank-name="pmic";
+ };
+ };
+
+ pmic1: pm8916@1 {
+ compatible = "qcom,spmi-pmic";
+ reg = <0x1 0x1>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ user1 {
+ label = "green:user1";
+ gpios = <&soc_gpios 21 0>;
+ };
+
+ user2 {
+ label = "green:user2";
+ gpios = <&soc_gpios 120 0>;
+ };
+
+ user3 {
+ label = "green:user3";
+ gpios = <&pm8916_gpios 0 0>;
+ };
+
+ user4 {
+ label = "green:user4";
+ gpios = <&pm8916_gpios 1 0>;
+ };
+ };
+};
+
+#include "dragonboard410c-uboot.dtsi"
config SYS_SOC
default "snapdragon"
+choice
+ prompt "Snapdragon board select"
+
+config TARGET_DRAGONBOARD410C
+ bool "96Boards Dragonboard 410C"
+ help
+ Support for 96Boards Dragonboard 410C. This board complies with
+ 96Board Open Platform Specifications. Features:
+ - Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
+ - 1GiB RAM
+ - 8GiB eMMC, uSD slot
+ - WiFi, Bluetooth and GPS module
+ - 2x Host, 1x Device USB port
+ - HDMI
+ - 20-pin low speed and 40-pin high speed expanders, 4 LED, 3 buttons
+
+endchoice
+
+source "board/qualcomm/dragonboard410c/Kconfig"
+
endif
--- /dev/null
+if TARGET_DRAGONBOARD410C
+
+config SYS_BOARD
+ default "dragonboard410c"
+
+config SYS_VENDOR
+ default "qualcomm"
+
+config SYS_SOC
+ default "apq8016"
+
+config SYS_CONFIG_NAME
+ default "dragonboard410c"
+
+endif
--- /dev/null
+DRAGONBOARD410C BOARD
+M: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+S: Maintained
+F: board/qualcomm/dragonboard410c/
+F: include/configs/dragonboard410c.h
+F: configs/dragonboard410c_defconfig
--- /dev/null
+#
+# (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := dragonboard410c.o
+extra-y += head.o
--- /dev/null
+/*
+ * Board init file for Dragonboard 410C
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <usb.h>
+#include <asm/gpio.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+ gd->ram_size = PHYS_SDRAM_1_SIZE;
+ return 0;
+}
+
+void dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+}
+
+
+int board_prepare_usb(enum usb_init_type type)
+{
+ static struct udevice *pmic_gpio;
+ static struct gpio_desc hub_reset, usb_sel;
+ int ret = 0, node;
+
+ if (!pmic_gpio) {
+ ret = uclass_get_device_by_name(UCLASS_GPIO,
+ "pm8916_gpios@c000",
+ &pmic_gpio);
+ if (ret < 0) {
+ printf("Failed to find pm8916_gpios@c000 node.\n");
+ return ret;
+ }
+ }
+
+ /* Try to request gpios needed to start usb host on dragonboard */
+ if (!dm_gpio_is_valid(&hub_reset)) {
+ node = fdt_subnode_offset(gd->fdt_blob, pmic_gpio->of_offset,
+ "usb_hub_reset_pm");
+ if (node < 0) {
+ printf("Failed to find usb_hub_reset_pm dt node.\n");
+ return node;
+ }
+ ret = gpio_request_by_name_nodev(gd->fdt_blob, node, "gpios", 0,
+ &hub_reset, 0);
+ if (ret < 0) {
+ printf("Failed to request usb_hub_reset_pm gpio.\n");
+ return ret;
+ }
+ }
+
+ if (!dm_gpio_is_valid(&usb_sel)) {
+ node = fdt_subnode_offset(gd->fdt_blob, pmic_gpio->of_offset,
+ "usb_sw_sel_pm");
+ if (node < 0) {
+ printf("Failed to find usb_sw_sel_pm dt node.\n");
+ return 0;
+ }
+ ret = gpio_request_by_name_nodev(gd->fdt_blob, node, "gpios", 0,
+ &usb_sel, 0);
+ if (ret < 0) {
+ printf("Failed to request usb_sw_sel_pm gpio.\n");
+ return ret;
+ }
+ }
+
+ if (type == USB_INIT_HOST) {
+ /* Start USB Hub */
+ dm_gpio_set_dir_flags(&hub_reset,
+ GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
+ mdelay(100);
+ /* Switch usb to host connectors */
+ dm_gpio_set_dir_flags(&usb_sel,
+ GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
+ mdelay(100);
+ } else { /* Device */
+ /* Disable hub */
+ dm_gpio_set_dir_flags(&hub_reset, GPIOD_IS_OUT);
+ /* Switch back to device connector */
+ dm_gpio_set_dir_flags(&usb_sel, GPIOD_IS_OUT);
+ }
+
+ return 0;
+}
+
+int board_init(void)
+{
+ return 0;
+}
+
+/* Check for vol- button - if pressed - stop autoboot */
+int misc_init_r(void)
+{
+ struct udevice *pon;
+ struct gpio_desc resin;
+ int node, ret;
+
+ ret = uclass_get_device_by_name(UCLASS_GPIO, "pm8916_pon@800", &pon);
+ if (ret < 0) {
+ printf("Failed to find PMIC pon node. Check device tree\n");
+ return 0;
+ }
+
+ node = fdt_subnode_offset(gd->fdt_blob, pon->of_offset, "key_vol_down");
+ if (node < 0) {
+ printf("Failed to find key_vol_down node. Check device tree\n");
+ return 0;
+ }
+
+ if (gpio_request_by_name_nodev(gd->fdt_blob, node, "gpios", 0, &resin,
+ 0)) {
+ printf("Failed to request key_vol_down button.\n");
+ return 0;
+ }
+
+ if (dm_gpio_get_value(&resin)) {
+ setenv("bootdelay", "-1");
+ printf("Power button pressed - dropping to console.\n");
+ }
+
+ return 0;
+}
--- /dev/null
+/*
+ * ARM64 header for proper chain-loading with Little Kernel.
+ *
+ * Little Kernel shipped with Dragonboard410C boots standard Linux images for
+ * ARM64. This file adds header that is required to boot U-Boot properly.
+ *
+ * For details see:
+ * https://www.kernel.org/doc/Documentation/arm64/booting.txt
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <config.h>
+
+.global _arm64_header
+_arm64_header:
+ b _start
+ .word 0
+ /* Image load offset from start of RAM, little-endian */
+ .quad CONFIG_SYS_TEXT_BASE-PHYS_SDRAM_1
+ /* Effective size of kernel image, little-endian */
+ .quad 0 /* 0x60000 - ignored */
+ /* Informative flags, little-endian */
+ .quad 0
+ .quad 0 /* reserved */
+ .quad 0 /* reserved */
+ .quad 0 /* reserved */
+ .byte 0x41 /* Magic number, "ARM\x64" */
+ .byte 0x52
+ .byte 0x4d
+ .byte 0x64
+ .word 0 /* reserved */
--- /dev/null
+#
+# (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+Build & Run instructions:
+
+1) Install mkbootimg and dtbTool from
+ git://codeaurora.org/quic/kernel/skales (15ece94f09 worked for me)
+2) Setup CROSS_COMPILE to aarch64 compiler
+3) make dragonboard410c_config
+4) make
+5) generate fake, empty ramdisk (can have 0 bytes)
+$ touch rd
+
+6) Generate qualcomm device tree table with dtbTool [1]
+$ dtbTool -o dt.img arch/arm/dts
+
+7) Generate Android boot image with mkbootimg [2]:
+$ mkbootimg --kernel=u-boot-dtb.bin --output=u-boot.img --dt=dt.img \
+ --pagesize 2048 --base 0x80000000 --ramdisk=rd --cmdline=""
+
+8) Enter fastboot (reboot board with vol- button pressed)
+
+9) Boot it:
+$ fastboot boot u-boot.img
+or flash as kernel:
+$ fastboot flash boot u-boot.img
+$ fastboot reboot
+
+
+What is working:
+- UART
+- GPIO (SoC)
+- SD
+- eMMC
+- Reset
+- USB in EHCI mode (usb starts does switch device->host, usb stop does the opposite)
+- PMIC GPIOS (but not in generic subsystem)
+- PMIC "special" buttons (power, vol-)
+
+What is not working / known bugs:
+- SDHCI is slow (~2.5MiB/s for SD and eMMC)
+
+[1] To boot any kernel image, Little Kernel requires valid device tree for the
+platform it runs on. dtbTool creates device tree table that Little Kernel scans.
+Later on proper device tree is passed to next boot stage.
+Full device tree is not required to boot u-boot. Enough would be:
+/dts-v1/;
+
+/ {
+ model = "Qualcomm Technologies, Inc. Dragonboard 410c";
+ compatible = "qcom,dragonboard", "qcom,apq8016-sbc";
+ qcom,msm-id = <0xce 0x0 0xf8 0x0 0xf9 0x0 0xfa 0x0 0xf7 0x0>;
+ qcom,board-id = <0x10018 0x0>;
+ #address-cells = <0x2>;
+ #size-cells = <0x2>;
+ chosen { };
+ aliases { };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x80000000 0 0x3da00000>;
+ };
+};
+
+but for simplicity (and because size of image is not that critical) we use
+existing Qualcomm device trees.
+
+[2] Note that ramdisk is required, even if it is unused.
--- /dev/null
+/*
+ * Override linker script for fastboot-readable images
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * Based on arch/arm/cpu/armv8/u-boot.lds (Just add header)
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+OUTPUT_FORMAT("elf64-littleaarch64", "elf64-littleaarch64", "elf64-littleaarch64")
+OUTPUT_ARCH(aarch64)
+ENTRY(_arm64_header)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(8);
+ .text :
+ {
+ *(.__image_copy_start)
+ board/qualcomm/dragonboard410c/head.o (.text*)
+ CPUDIR/start.o (.text*)
+ *(.text*)
+ }
+
+ . = ALIGN(8);
+ .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+ . = ALIGN(8);
+ .data : {
+ *(.data*)
+ }
+
+ . = ALIGN(8);
+
+ . = .;
+
+ . = ALIGN(8);
+ .u_boot_list : {
+ KEEP(*(SORT(.u_boot_list*)));
+ }
+
+ . = ALIGN(8);
+
+ .image_copy_end :
+ {
+ *(.__image_copy_end)
+ }
+
+ . = ALIGN(8);
+
+ .rel_dyn_start :
+ {
+ *(.__rel_dyn_start)
+ }
+
+ .rela.dyn : {
+ *(.rela*)
+ }
+
+ .rel_dyn_end :
+ {
+ *(.__rel_dyn_end)
+ }
+
+ _end = .;
+
+ . = ALIGN(8);
+
+ .bss_start : {
+ KEEP(*(.__bss_start));
+ }
+
+ .bss : {
+ *(.bss*)
+ . = ALIGN(8);
+ }
+
+ .bss_end : {
+ KEEP(*(.__bss_end));
+ }
+
+ /DISCARD/ : { *(.dynsym) }
+ /DISCARD/ : { *(.dynstr*) }
+ /DISCARD/ : { *(.dynamic*) }
+ /DISCARD/ : { *(.plt*) }
+ /DISCARD/ : { *(.interp*) }
+ /DISCARD/ : { *(.gnu*) }
+}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SNAPDRAGON=y
+CONFIG_DEFAULT_DEVICE_TREE="dragonboard410c"
+CONFIG_SYS_PROMPT="dragonboard410c => "
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_USB=y
+CONFIG_CLK=y
+CONFIG_MSM_GPIO=y
+CONFIG_PM8916_GPIO=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_RESET=y
+CONFIG_DM_MMC=y
+CONFIG_MSM_SDHCI=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_PM8916=y
+CONFIG_MSM_SERIAL=y
+CONFIG_SPMI_MSM=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_MSM=y
+CONFIG_USB_ULPI_VIEWPORT=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_STORAGE=y
--- /dev/null
+/*
+ * Board configuration file for Dragonboard 410C
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIGS_DRAGONBOARD410C_H
+#define __CONFIGS_DRAGONBOARD410C_H
+
+#include <linux/sizes.h>
+#include <asm/arch/sysmap-apq8016.h>
+
+#define CONFIG_IDENT_STRING "\nQualcomm-DragonBoard 410C"
+
+#define CONFIG_MISC_INIT_R /* To stop autoboot */
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM_1 0x80000000
+/* 1008 MB (the last ~30Mb are secured for TrustZone by ATF*/
+#define PHYS_SDRAM_1_SIZE 0x3da00000
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_TEXT_BASE 0x80080000
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0)
+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x80000)
+#define CONFIG_SYS_BOOTM_LEN 0x1000000 /* 16MB max kernel size */
+
+/* UART */
+#define CONFIG_BAUDRATE 115200
+
+/* Generic Timer Definitions */
+#define COUNTER_FREQUENCY 19000000
+
+/* This are needed to have proper mmc support */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_SDHCI
+
+#define CONFIG_SYS_LDSCRIPT "board/qualcomm/dragonboard410c/u-boot.lds"
+
+/* Fixup - in init code we switch from device to host mode,
+ * it has to be done after each HCD reset */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+
+#define CONFIG_USB_HOST_ETHER /* Enable USB Networking */
+
+/* Support all possible USB ethernet dongles */
+#define CONFIG_USB_ETHER_DM9601
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_ETHER_ASIX88179
+#define CONFIG_USB_ETHER_MCS7830
+#define CONFIG_USB_ETHER_SMSC95XX
+
+/* Libraries */
+#define CONFIG_MD5
+
+/* Extra Commands */
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_GPIO
+#define CONFIG_CMD_GPT
+#define CONFIG_CMD_MD5SUM
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MMC
+/* Enable that for switching of boot partitions */
+/* Disabled by default as some sub-commands can brick eMMC */
+/*#define CONFIG_SUPPORT_EMMC_BOOT */
+#define CONFIG_CMD_PART
+#define CONFIG_CMD_REGINFO /* Register dump */
+#define CONFIG_CMD_TFTP
+#define CONFIG_CMD_TIMER
+#define CONFIG_CMD_UNZIP
+
+/* Partition table support */
+#define HAVE_BLOCK_DEVICE /* Needed for partition commands */
+#define CONFIG_PARTITION_UUIDS
+
+#include <config_distro_defaults.h>
+
+/* BOOTP options */
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+/* Environment - Boot*/
+#define CONFIG_BOOTARGS "console=ttyMSM0,115200n8"
+
+#define BOOT_TARGET_DEVICES(func) \
+ func(USB, usb, 0) \
+ func(MMC, mmc, 0) \
+ func(MMC, mmc, 1) \
+ func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+
+/* Does what recovery does */
+#define REFLASH(file, part) \
+"part start mmc 0 "#part" start && "\
+"part size mmc 0 "#part" size && "\
+"tftp $loadaddr "#file" && " \
+"mmc write $loadaddr $start $size && "
+
+
+#define CONFIG_ENV_REFLASH \
+"mmc dev 0 && "\
+"usb start && "\
+"dhcp && "\
+"tftp $loadaddr dragonboard/rescue/gpt_both0.bin && "\
+"mmc write $loadaddr 0 43 && " \
+"mmc rescan && "\
+REFLASH(dragonboard/rescue/NON-HLOS.bin, 1)\
+REFLASH(dragonboard/rescue/sbl1.mbn, 2)\
+REFLASH(dragonboard/rescue/rpm.mbn, 3)\
+REFLASH(dragonboard/rescue/tz.mbn, 4)\
+REFLASH(dragonboard/rescue/hyp.mbn, 5)\
+REFLASH(dragonboard/rescue/sec.dat, 6)\
+REFLASH(dragonboard/rescue/emmc_appsboot.mbn, 7)\
+REFLASH(dragonboard/u-boot.img, 8)\
+"usb stop &&"\
+"echo Reflash completed"
+
+/* Environment */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "reflash="CONFIG_ENV_REFLASH"\0"\
+ "loadaddr=0x81000000\0" \
+ "fdt_high=0xffffffffffffffff\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "linux_image=Image\0" \
+ "linux_addr=0x81000000\0"\
+ "fdt_image=apq8016-sbc.dtb\0" \
+ "fdt_addr=0x83000000\0"\
+ "ramdisk_addr=0x84000000\0"\
+ BOOTENV
+
+#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_SIZE 0x1000
+#define CONFIG_ENV_VARS_UBOOT_CONFIG
+#define CONFIG_SYS_NO_FLASH
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_8M)
+
+/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_MAXARGS 64 /* max command args */
+
+#endif
projects / people / ms / u-boot.git / commitdiff
