armadillo ARM720T
+Dirk Behme <dirk.behme@gmail.com>
+
+ omap3_beagle ARM CORTEX-A8 (OMAP3530 SoC)
+
Rishi Bhattacharya <rishi@ti.com>
omap5912osk ARM926EJS
imx31_litekit i.MX31
imx31_phycore i.MX31
+Grazvydas Ignotas <notasas@gmail.com>
+
+ omap3_pandora ARM CORTEX-A8 (OMAP3xx SoC)
+
Gary Jennejohn <gj@denx.de>
smdk2400 ARM920T
mx31ads i.MX31
SMDK6400 S3C6400
+Nishanth Menon <nm@ti.com>
+
+ omap3_zoom1 ARM CORTEX-A8 (OMAP3xx SoC)
+
David Müller <d.mueller@elsoft.ch>
smdk2410 ARM920T
omap730p2 ARM926EJS
+Manikandan Pillai <mani.pillai@ti.com>
+
+ omap3_evm ARM CORTEX-A8 (OMAP3xx SoC)
+
Stelian Pop <stelian.pop@leadtechdesign.com>
at91cap9adk ARM926EJS (AT91CAP9 SoC)
pdnb3 xscale
scpu xscale
+Alessandro Rubini <rubini@unipv.it>
+Nomadik Linux Team <STN_WMM_nomadik_linux@list.st.com>
+
+ nmdk8815 ARM926EJS (Nomadik 8815 Soc)
+
+Steve Sakoman <sakoman@gmail.com>
+
+ omap3_overo ARM CORTEX-A8 (OMAP3xx SoC)
+
Robert Schwebel <r.schwebel@pengutronix.de>
csb226 xscale
mx1ads \
mx1fs2 \
netstar \
+ nmdk8815 \
omap1510inn \
omap1610h2 \
omap1610inn \
smdk6400 \
"
+#########################################################################
+## ARM Cortex-A8 Systems
+#########################################################################
+LIST_ARM_CORTEX_A8=" \
+ omap3_beagle \
+ omap3_overo \
+ omap3_evm \
+ omap3_pandora \
+ omap3_zoom1 \
+"
+
#########################################################################
## AT91 Systems
#########################################################################
## ARM groups
#########################################################################
-LIST_arm=" \
- ${LIST_SA} \
- ${LIST_ARM7} \
- ${LIST_ARM9} \
- ${LIST_ARM10} \
- ${LIST_ARM11} \
- ${LIST_at91} \
- ${LIST_pxa} \
- ${LIST_ixp} \
+LIST_arm=" \
+ ${LIST_SA} \
+ ${LIST_ARM7} \
+ ${LIST_ARM9} \
+ ${LIST_ARM10} \
+ ${LIST_ARM11} \
+ ${LIST_ARM_CORTEX_A8} \
+ ${LIST_at91} \
+ ${LIST_pxa} \
+ ${LIST_ixp} \
"
#########################################################################
for arg in $@
do
case "$arg" in
- arm|SA|ARM7|ARM9|ARM10|ARM11|at91|ixp|pxa \
+ arm|SA|ARM7|ARM9|ARM10|ARM11|ARM_CORTEX_A8|at91|ixp|pxa \
|avr32 \
|blackfin \
|coldfire \
ap920t_config \
ap926ejs_config \
ap946es_config: unconfig
- @board/integratorap/split_by_variant.sh $@
+ @board/armltd/integratorap/split_by_variant.sh $@
integratorcp_config \
cp_config \
cp922_config \
cp922_XA10_config \
cp1026_config: unconfig
- @board/integratorcp/split_by_variant.sh $@
+ @board/armltd/integratorcp/split_by_variant.sh $@
davinci_dvevm_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm926ejs dvevm davinci davinci
netstar_config: unconfig
@$(MKCONFIG) $(@:_config=) arm arm925t netstar
+nmdk8815_config \
+nmdk8815_onenand_config: unconfig
+ @mkdir -p $(obj)include
+ @ > $(obj)include/config.h
+ @if [ "$(findstring _onenand, $@)" ] ; then \
+ echo "#define CONFIG_BOOT_ONENAND" >> $(obj)include/config.h; \
+ $(XECHO) "... configured for OneNand Flash"; \
+ else \
+ $(XECHO) "... configured for Nand Flash"; \
+ fi
+ @$(MKCONFIG) -a nmdk8815 arm arm926ejs nmdk8815 st nomadik
+
omap1510inn_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm925t omap1510inn
@$(MKCONFIG) $(@:_config=) arm arm920t scb9328 NULL imx
smdk2400_config : unconfig
- @$(MKCONFIG) $(@:_config=) arm arm920t smdk2400 NULL s3c24x0
+ @$(MKCONFIG) $(@:_config=) arm arm920t smdk2400 samsung s3c24x0
smdk2410_config : unconfig
- @$(MKCONFIG) $(@:_config=) arm arm920t smdk2410 NULL s3c24x0
+ @$(MKCONFIG) $(@:_config=) arm arm920t smdk2410 samsung s3c24x0
-SX1_config : unconfig
- @$(MKCONFIG) $(@:_config=) arm arm925t sx1
+SX1_stdout_serial_config \
+SX1_config: unconfig
+ @mkdir -p $(obj)include
+ @if [ "$(findstring _stdout_serial_, $@)" ] ; then \
+ echo "#undef CONFIG_STDOUT_USBTTY" >> $(obj)include/config.h ; \
+ $(XECHO) "... configured for stdout serial"; \
+ else \
+ echo "#define CONFIG_STDOUT_USBTTY" >> $(obj)include/config.h ; \
+ $(XECHO) "... configured for stdout usbtty"; \
+ fi;
+ @$(MKCONFIG) SX1 arm arm925t sx1
# TRAB default configuration: 8 MB Flash, 32 MB RAM
xtract_trab = $(subst _bigram,,$(subst _bigflash,,$(subst _old,,$(subst _config,,$1))))
versatile_config \
versatileab_config \
versatilepb_config : unconfig
- @board/versatile/split_by_variant.sh $@
+ @board/armltd/versatile/split_by_variant.sh $@
voiceblue_config: unconfig
@$(MKCONFIG) $(@:_config=) arm arm925t voiceblue
SMN42_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm720t SMN42 siemens lpc2292
+#########################################################################
+## ARM CORTEX Systems
+#########################################################################
+
+omap3_beagle_config : unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 beagle omap3 omap3
+
+omap3_overo_config : unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 overo omap3 omap3
+
+omap3_evm_config : unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 evm omap3 omap3
+
+omap3_pandora_config : unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 pandora omap3 omap3
+
+omap3_zoom1_config : unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 zoom1 omap3 omap3
+
#########################################################################
## XScale Systems
#########################################################################
--- /dev/null
+/integratorap/u-boot.lds
+/integratorcp/u-boot.lds
fi
mkdir -p ${obj}include
-mkdir -p ${obj}board/integratorap
+mkdir -p ${obj}board/armltd/integratorap
mv tmp.fil ${obj}include/config.h
# ---------------------------------------------------------
# Ensure correct core object loaded first in U-Boot image
# ---------------------------------------------------------
-sed -r 's/CPU_FILE/cpu\/'$cpu'\/start.o/; s/#.*//' ${src}board/integratorap/u-boot.lds.template > ${obj}board/integratorap/u-boot.lds
+sed -r 's/CPU_FILE/cpu\/'$cpu'\/start.o/; s/#.*//' ${src}board/armltd/integratorap/u-boot.lds.template > ${obj}board/armltd/integratorap/u-boot.lds
# ---------------------------------------------------------
# Complete the configuration
# ---------------------------------------------------------
-$MKCONFIG -a integratorap arm $cpu integratorap;
+$MKCONFIG -a integratorap arm $cpu integratorap armltd;
echo "Variant:: $variant with core $cpu"
fi
mkdir -p ${obj}include
-mkdir -p ${obj}board/integratorcp
+mkdir -p ${obj}board/armltd/integratorcp
mv tmp.fil ${obj}include/config.h
# ---------------------------------------------------------
# Ensure correct core object loaded first in U-Boot image
# ---------------------------------------------------------
-sed -r 's/CPU_FILE/cpu\/'$cpu'\/start.o/; s/#.*//' ${src}board/integratorcp/u-boot.lds.template > ${obj}board/integratorcp/u-boot.lds
+sed -r 's/CPU_FILE/cpu\/'$cpu'\/start.o/; s/#.*//' ${src}board/armltd/integratorcp/u-boot.lds.template > ${obj}board/armltd/integratorcp/u-boot.lds
# ---------------------------------------------------------
# Complete the configuration
# ---------------------------------------------------------
-$MKCONFIG -a integratorcp arm $cpu integratorcp;
+$MKCONFIG -a integratorcp arm $cpu integratorcp armltd;
echo "Variant:: $variant with core $cpu"
# ---------------------------------------------------------
# Complete the configuration
# ---------------------------------------------------------
-$MKCONFIG -a versatile arm arm926ejs versatile NULL versatile
+$MKCONFIG -a versatile arm arm926ejs versatile armltd versatile
echo "Variant:: $variant"
--- /dev/null
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := beagle.o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+/*
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ * Sunil Kumar <sunilsaini05@gmail.com>
+ * Shashi Ranjan <shashiranjanmca05@gmail.com>
+ *
+ * Derived from Beagle Board and 3430 SDP code by
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-types.h>
+#include "beagle.h"
+
+/******************************************************************************
+ * Routine: board_init
+ * Description: Early hardware init.
+ *****************************************************************************/
+int board_init(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+ /* board id for Linux */
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP3_BEAGLE;
+ /* boot param addr */
+ gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+ return 0;
+}
+
+/******************************************************************************
+ * Routine: misc_init_r
+ * Description: Configure board specific parts
+ *****************************************************************************/
+int misc_init_r(void)
+{
+ gpio_t *gpio5_base = (gpio_t *)OMAP34XX_GPIO5_BASE;
+ gpio_t *gpio6_base = (gpio_t *)OMAP34XX_GPIO6_BASE;
+
+ power_init_r();
+
+ /* Configure GPIOs to output */
+ writel(~(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1), &gpio6_base->oe);
+ writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
+ GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
+
+ /* Set GPIOs */
+ writel(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1,
+ &gpio6_base->setdataout);
+ writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
+ GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
+
+ return 0;
+}
+
+/******************************************************************************
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ * hardware. Many pins need to be moved from protect to primary
+ * mode.
+ *****************************************************************************/
+void set_muxconf_regs(void)
+{
+ MUX_BEAGLE();
+}
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Dirk Behme <dirk.behme@gmail.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _BEAGLE_H_
+#define _BEAGLE_H_
+
+const omap3_sysinfo sysinfo = {
+ SDP_3430_V1,
+ SDP_3430_V2,
+ DDR_STACKED,
+ "3530",
+ "OMAP3 Beagle board",
+#if defined(CONFIG_ENV_IS_IN_ONENAND)
+ "OneNAND",
+#else
+ "NAND",
+#endif
+};
+
+/*
+ * IEN - Input Enable
+ * IDIS - Input Disable
+ * PTD - Pull type Down
+ * PTU - Pull type Up
+ * DIS - Pull type selection is inactive
+ * EN - Pull type selection is active
+ * M0 - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_BEAGLE() \
+ /*SDRC*/\
+ MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) /*SDRC_D0*/\
+ MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /*SDRC_D1*/\
+ MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /*SDRC_D2*/\
+ MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /*SDRC_D3*/\
+ MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /*SDRC_D4*/\
+ MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /*SDRC_D5*/\
+ MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /*SDRC_D6*/\
+ MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /*SDRC_D7*/\
+ MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /*SDRC_D8*/\
+ MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /*SDRC_D9*/\
+ MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /*SDRC_D10*/\
+ MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /*SDRC_D11*/\
+ MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /*SDRC_D12*/\
+ MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /*SDRC_D13*/\
+ MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /*SDRC_D14*/\
+ MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /*SDRC_D15*/\
+ MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /*SDRC_D16*/\
+ MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /*SDRC_D17*/\
+ MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /*SDRC_D18*/\
+ MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /*SDRC_D19*/\
+ MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /*SDRC_D20*/\
+ MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /*SDRC_D21*/\
+ MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /*SDRC_D22*/\
+ MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /*SDRC_D23*/\
+ MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /*SDRC_D24*/\
+ MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /*SDRC_D25*/\
+ MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /*SDRC_D26*/\
+ MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /*SDRC_D27*/\
+ MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /*SDRC_D28*/\
+ MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /*SDRC_D29*/\
+ MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /*SDRC_D30*/\
+ MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /*SDRC_D31*/\
+ MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /*SDRC_CLK*/\
+ MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /*SDRC_DQS0*/\
+ MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /*SDRC_DQS1*/\
+ MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /*SDRC_DQS2*/\
+ MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /*SDRC_DQS3*/\
+ /*GPMC*/\
+ MUX_VAL(CP(GPMC_A1), (IDIS | PTD | DIS | M0)) /*GPMC_A1*/\
+ MUX_VAL(CP(GPMC_A2), (IDIS | PTD | DIS | M0)) /*GPMC_A2*/\
+ MUX_VAL(CP(GPMC_A3), (IDIS | PTD | DIS | M0)) /*GPMC_A3*/\
+ MUX_VAL(CP(GPMC_A4), (IDIS | PTD | DIS | M0)) /*GPMC_A4*/\
+ MUX_VAL(CP(GPMC_A5), (IDIS | PTD | DIS | M0)) /*GPMC_A5*/\
+ MUX_VAL(CP(GPMC_A6), (IDIS | PTD | DIS | M0)) /*GPMC_A6*/\
+ MUX_VAL(CP(GPMC_A7), (IDIS | PTD | DIS | M0)) /*GPMC_A7*/\
+ MUX_VAL(CP(GPMC_A8), (IDIS | PTD | DIS | M0)) /*GPMC_A8*/\
+ MUX_VAL(CP(GPMC_A9), (IDIS | PTD | DIS | M0)) /*GPMC_A9*/\
+ MUX_VAL(CP(GPMC_A10), (IDIS | PTD | DIS | M0)) /*GPMC_A10*/\
+ MUX_VAL(CP(GPMC_D0), (IEN | PTD | DIS | M0)) /*GPMC_D0*/\
+ MUX_VAL(CP(GPMC_D1), (IEN | PTD | DIS | M0)) /*GPMC_D1*/\
+ MUX_VAL(CP(GPMC_D2), (IEN | PTD | DIS | M0)) /*GPMC_D2*/\
+ MUX_VAL(CP(GPMC_D3), (IEN | PTD | DIS | M0)) /*GPMC_D3*/\
+ MUX_VAL(CP(GPMC_D4), (IEN | PTD | DIS | M0)) /*GPMC_D4*/\
+ MUX_VAL(CP(GPMC_D5), (IEN | PTD | DIS | M0)) /*GPMC_D5*/\
+ MUX_VAL(CP(GPMC_D6), (IEN | PTD | DIS | M0)) /*GPMC_D6*/\
+ MUX_VAL(CP(GPMC_D7), (IEN | PTD | DIS | M0)) /*GPMC_D7*/\
+ MUX_VAL(CP(GPMC_D8), (IEN | PTD | DIS | M0)) /*GPMC_D8*/\
+ MUX_VAL(CP(GPMC_D9), (IEN | PTD | DIS | M0)) /*GPMC_D9*/\
+ MUX_VAL(CP(GPMC_D10), (IEN | PTD | DIS | M0)) /*GPMC_D10*/\
+ MUX_VAL(CP(GPMC_D11), (IEN | PTD | DIS | M0)) /*GPMC_D11*/\
+ MUX_VAL(CP(GPMC_D12), (IEN | PTD | DIS | M0)) /*GPMC_D12*/\
+ MUX_VAL(CP(GPMC_D13), (IEN | PTD | DIS | M0)) /*GPMC_D13*/\
+ MUX_VAL(CP(GPMC_D14), (IEN | PTD | DIS | M0)) /*GPMC_D14*/\
+ MUX_VAL(CP(GPMC_D15), (IEN | PTD | DIS | M0)) /*GPMC_D15*/\
+ MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /*GPMC_nCS0*/\
+ MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M0)) /*GPMC_nCS1*/\
+ MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M0)) /*GPMC_nCS2*/\
+ MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M0)) /*GPMC_nCS3*/\
+ MUX_VAL(CP(GPMC_NCS4), (IDIS | PTU | EN | M0)) /*GPMC_nCS4*/\
+ MUX_VAL(CP(GPMC_NCS5), (IDIS | PTD | DIS | M0)) /*GPMC_nCS5*/\
+ MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M1)) /*SYS_nDMA_REQ2*/\
+ MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M1)) /*SYS_nDMA_REQ3*/\
+ MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | DIS | M0)) /*GPMC_nBE1*/\
+ MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M0)) /*GPMC_WAIT2*/\
+ MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) /*GPMC_WAIT3*/\
+ MUX_VAL(CP(GPMC_CLK), (IDIS | PTD | DIS | M0)) /*GPMC_CLK*/\
+ MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /*GPMC_nADV_ALE*/\
+ MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\
+ MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\
+ MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTD | DIS | M0)) /*GPMC_nBE0_CLE*/\
+ MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0)) /*GPMC_nWP*/\
+ MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) /*GPMC_WAIT0*/\
+ MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) /*GPMC_WAIT1*/\
+ /*DSS*/\
+ MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
+ MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0)) /*DSS_HSYNC*/\
+ MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0)) /*DSS_VSYNC*/\
+ MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0)) /*DSS_ACBIAS*/\
+ MUX_VAL(CP(DSS_DATA0), (IDIS | PTD | DIS | M0)) /*DSS_DATA0*/\
+ MUX_VAL(CP(DSS_DATA1), (IDIS | PTD | DIS | M0)) /*DSS_DATA1*/\
+ MUX_VAL(CP(DSS_DATA2), (IDIS | PTD | DIS | M0)) /*DSS_DATA2*/\
+ MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M0)) /*DSS_DATA3*/\
+ MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M0)) /*DSS_DATA4*/\
+ MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M0)) /*DSS_DATA5*/\
+ MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0)) /*DSS_DATA6*/\
+ MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0)) /*DSS_DATA7*/\
+ MUX_VAL(CP(DSS_DATA8), (IDIS | PTD | DIS | M0)) /*DSS_DATA8*/\
+ MUX_VAL(CP(DSS_DATA9), (IDIS | PTD | DIS | M0)) /*DSS_DATA9*/\
+ MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0)) /*DSS_DATA10*/\
+ MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0)) /*DSS_DATA11*/\
+ MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0)) /*DSS_DATA12*/\
+ MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0)) /*DSS_DATA13*/\
+ MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0)) /*DSS_DATA14*/\
+ MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0)) /*DSS_DATA15*/\
+ MUX_VAL(CP(DSS_DATA16), (IDIS | PTD | DIS | M0)) /*DSS_DATA16*/\
+ MUX_VAL(CP(DSS_DATA17), (IDIS | PTD | DIS | M0)) /*DSS_DATA17*/\
+ MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M0)) /*DSS_DATA18*/\
+ MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0)) /*DSS_DATA19*/\
+ MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0)) /*DSS_DATA20*/\
+ MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0)) /*DSS_DATA21*/\
+ MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0)) /*DSS_DATA22*/\
+ MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0)) /*DSS_DATA23*/\
+ /*CAMERA*/\
+ MUX_VAL(CP(CAM_HS), (IEN | PTU | EN | M0)) /*CAM_HS */\
+ MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M0)) /*CAM_VS */\
+ MUX_VAL(CP(CAM_XCLKA), (IDIS | PTD | DIS | M0)) /*CAM_XCLKA*/\
+ MUX_VAL(CP(CAM_PCLK), (IEN | PTU | EN | M0)) /*CAM_PCLK*/\
+ MUX_VAL(CP(CAM_FLD), (IDIS | PTD | DIS | M4)) /*GPIO_98*/\
+ MUX_VAL(CP(CAM_D0), (IEN | PTD | DIS | M0)) /*CAM_D0*/\
+ MUX_VAL(CP(CAM_D1), (IEN | PTD | DIS | M0)) /*CAM_D1*/\
+ MUX_VAL(CP(CAM_D2), (IEN | PTD | DIS | M0)) /*CAM_D2*/\
+ MUX_VAL(CP(CAM_D3), (IEN | PTD | DIS | M0)) /*CAM_D3*/\
+ MUX_VAL(CP(CAM_D4), (IEN | PTD | DIS | M0)) /*CAM_D4*/\
+ MUX_VAL(CP(CAM_D5), (IEN | PTD | DIS | M0)) /*CAM_D5*/\
+ MUX_VAL(CP(CAM_D6), (IEN | PTD | DIS | M0)) /*CAM_D6*/\
+ MUX_VAL(CP(CAM_D7), (IEN | PTD | DIS | M0)) /*CAM_D7*/\
+ MUX_VAL(CP(CAM_D8), (IEN | PTD | DIS | M0)) /*CAM_D8*/\
+ MUX_VAL(CP(CAM_D9), (IEN | PTD | DIS | M0)) /*CAM_D9*/\
+ MUX_VAL(CP(CAM_D10), (IEN | PTD | DIS | M0)) /*CAM_D10*/\
+ MUX_VAL(CP(CAM_D11), (IEN | PTD | DIS | M0)) /*CAM_D11*/\
+ MUX_VAL(CP(CAM_XCLKB), (IDIS | PTD | DIS | M0)) /*CAM_XCLKB*/\
+ MUX_VAL(CP(CAM_WEN), (IEN | PTD | DIS | M4)) /*GPIO_167*/\
+ MUX_VAL(CP(CAM_STROBE), (IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
+ MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0)) /*CSI2_DX0*/\
+ MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0)) /*CSI2_DY0*/\
+ MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0)) /*CSI2_DX1*/\
+ MUX_VAL(CP(CSI2_DY1), (IEN | PTD | DIS | M0)) /*CSI2_DY1*/\
+ /*Audio Interface */\
+ MUX_VAL(CP(MCBSP2_FSX), (IEN | PTD | DIS | M0)) /*McBSP2_FSX*/\
+ MUX_VAL(CP(MCBSP2_CLKX), (IEN | PTD | DIS | M0)) /*McBSP2_CLKX*/\
+ MUX_VAL(CP(MCBSP2_DR), (IEN | PTD | DIS | M0)) /*McBSP2_DR*/\
+ MUX_VAL(CP(MCBSP2_DX), (IDIS | PTD | DIS | M0)) /*McBSP2_DX*/\
+ /*Expansion card */\
+ MUX_VAL(CP(MMC1_CLK), (IDIS | PTU | EN | M0)) /*MMC1_CLK*/\
+ MUX_VAL(CP(MMC1_CMD), (IEN | PTU | EN | M0)) /*MMC1_CMD*/\
+ MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | EN | M0)) /*MMC1_DAT0*/\
+ MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | EN | M0)) /*MMC1_DAT1*/\
+ MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | EN | M0)) /*MMC1_DAT2*/\
+ MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | EN | M0)) /*MMC1_DAT3*/\
+ MUX_VAL(CP(MMC1_DAT4), (IEN | PTU | EN | M0)) /*MMC1_DAT4*/\
+ MUX_VAL(CP(MMC1_DAT5), (IEN | PTU | EN | M0)) /*MMC1_DAT5*/\
+ MUX_VAL(CP(MMC1_DAT6), (IEN | PTU | EN | M0)) /*MMC1_DAT6*/\
+ MUX_VAL(CP(MMC1_DAT7), (IEN | PTU | EN | M0)) /*MMC1_DAT7*/\
+ /*Wireless LAN */\
+ MUX_VAL(CP(MMC2_CLK), (IEN | PTU | EN | M4)) /*GPIO_130*/\
+ MUX_VAL(CP(MMC2_CMD), (IEN | PTU | EN | M4)) /*GPIO_131*/\
+ MUX_VAL(CP(MMC2_DAT0), (IEN | PTU | EN | M4)) /*GPIO_132*/\
+ MUX_VAL(CP(MMC2_DAT1), (IEN | PTU | EN | M4)) /*GPIO_133*/\
+ MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | EN | M4)) /*GPIO_134*/\
+ MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M4)) /*GPIO_135*/\
+ MUX_VAL(CP(MMC2_DAT4), (IEN | PTU | EN | M4)) /*GPIO_136*/\
+ MUX_VAL(CP(MMC2_DAT5), (IEN | PTU | EN | M4)) /*GPIO_137*/\
+ MUX_VAL(CP(MMC2_DAT6), (IEN | PTU | EN | M4)) /*GPIO_138*/\
+ MUX_VAL(CP(MMC2_DAT7), (IEN | PTU | EN | M4)) /*GPIO_139*/\
+ /*Bluetooth*/\
+ MUX_VAL(CP(MCBSP3_DX), (IDIS | PTD | DIS | M4)) /*GPIO_140*/\
+ MUX_VAL(CP(MCBSP3_DR), (IDIS | PTD | DIS | M4)) /*GPIO_142*/\
+ MUX_VAL(CP(MCBSP3_CLKX), (IDIS | PTD | DIS | M4)) /*GPIO_141*/\
+ MUX_VAL(CP(MCBSP3_FSX), (IDIS | PTD | DIS | M4)) /*GPIO_143*/\
+ MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M0)) /*UART2_CTS*/\
+ MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M0)) /*UART2_RTS*/\
+ MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M0)) /*UART2_TX*/\
+ MUX_VAL(CP(UART2_RX), (IDIS | PTD | DIS | M4)) /*GPIO_147*/\
+ /*Modem Interface */\
+ MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) /*UART1_TX*/\
+ MUX_VAL(CP(UART1_RTS), (IDIS | PTD | DIS | M4)) /*GPIO_149*/ \
+ MUX_VAL(CP(UART1_CTS), (IDIS | PTD | DIS | M4)) /*GPIO_150*/ \
+ MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0)) /*UART1_RX*/\
+ MUX_VAL(CP(MCBSP4_CLKX), (IEN | PTD | DIS | M1)) /*SSI1_DAT_RX*/\
+ MUX_VAL(CP(MCBSP4_DR), (IEN | PTD | DIS | M1)) /*SSI1_FLAG_RX*/\
+ MUX_VAL(CP(MCBSP4_DX), (IEN | PTD | DIS | M1)) /*SSI1_RDY_RX*/\
+ MUX_VAL(CP(MCBSP4_FSX), (IEN | PTD | DIS | M1)) /*SSI1_WAKE*/\
+ MUX_VAL(CP(MCBSP1_CLKR), (IDIS | PTD | DIS | M4)) /*GPIO_156*/\
+ MUX_VAL(CP(MCBSP1_FSR), (IDIS | PTU | EN | M4)) /*GPIO_157*/\
+ MUX_VAL(CP(MCBSP1_DX), (IDIS | PTD | DIS | M4)) /*GPIO_158*/\
+ MUX_VAL(CP(MCBSP1_DR), (IDIS | PTD | DIS | M4)) /*GPIO_159*/\
+ MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) /*McBSP_CLKS*/\
+ MUX_VAL(CP(MCBSP1_FSX), (IDIS | PTD | DIS | M4)) /*GPIO_161*/\
+ MUX_VAL(CP(MCBSP1_CLKX), (IDIS | PTD | DIS | M4)) /*GPIO_162*/\
+ /*Serial Interface*/\
+ MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTD | EN | M0)) /*UART3_CTS_RCTX*/\
+ MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTD | DIS | M0)) /*UART3_RTS_SD */\
+ MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0)) /*UART3_RX_IRRX*/\
+ MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0)) /*UART3_TX_IRTX*/\
+ MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0)) /*HSUSB0_CLK*/\
+ MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0)) /*HSUSB0_STP*/\
+ MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0)) /*HSUSB0_DIR*/\
+ MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0)) /*HSUSB0_NXT*/\
+ MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA0*/\
+ MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA1*/\
+ MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA2*/\
+ MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA3*/\
+ MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA4*/\
+ MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA5*/\
+ MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA6*/\
+ MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA7*/\
+ MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) /*I2C1_SCL*/\
+ MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) /*I2C1_SDA*/\
+ MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M4)) /*GPIO_168*/\
+ MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M4)) /*GPIO_183*/\
+ MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0)) /*I2C3_SCL*/\
+ MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0)) /*I2C3_SDA*/\
+ MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0)) /*I2C4_SCL*/\
+ MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0)) /*I2C4_SDA*/\
+ MUX_VAL(CP(HDQ_SIO), (IDIS | PTU | EN | M4)) /*GPIO_170*/\
+ MUX_VAL(CP(MCSPI1_CLK), (IEN | PTU | EN | M4)) /*GPIO_171*/\
+ MUX_VAL(CP(MCSPI1_SIMO), (IEN | PTU | EN | M4)) /*GPIO_172*/\
+ MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M0)) /*McSPI1_SOMI*/\
+ MUX_VAL(CP(MCSPI1_CS0), (IEN | PTD | EN | M0)) /*McSPI1_CS0*/\
+ MUX_VAL(CP(MCSPI1_CS1), (IDIS | PTD | EN | M0)) /*McSPI1_CS1*/\
+ MUX_VAL(CP(MCSPI1_CS2), (IDIS | PTD | DIS | M4)) /*GPIO_176*/\
+ /* USB EHCI (port 2) */\
+ MUX_VAL(CP(MCSPI1_CS3), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA2*/\
+ MUX_VAL(CP(MCSPI2_CLK), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA7*/\
+ MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA4*/\
+ MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA5*/\
+ MUX_VAL(CP(MCSPI2_CS0), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA6*/\
+ MUX_VAL(CP(MCSPI2_CS1), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA3*/\
+ MUX_VAL(CP(ETK_D10_ES2), (IDIS | PTU | DIS | M3)) /*HSUSB2_CLK*/\
+ MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTU | DIS | M3)) /*HSUSB2_STP*/\
+ MUX_VAL(CP(ETK_D12_ES2), (IEN | PTU | DIS | M3)) /*HSUSB2_DIR*/\
+ MUX_VAL(CP(ETK_D13_ES2), (IEN | PTU | DIS | M3)) /*HSUSB2_NXT*/\
+ MUX_VAL(CP(ETK_D14_ES2), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA0*/\
+ MUX_VAL(CP(ETK_D15_ES2), (IEN | PTU | DIS | M3)) /*HSUSB2_DATA1*/\
+ /*Control and debug */\
+ MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)) /*SYS_32K*/\
+ MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) /*SYS_CLKREQ*/\
+ MUX_VAL(CP(SYS_NIRQ), (IEN | PTU | EN | M0)) /*SYS_nIRQ*/\
+ MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) /*GPIO_2*/\
+ MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) /*GPIO_3*/\
+ MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /*GPIO_4 - MMC1_WP*/\
+ MUX_VAL(CP(SYS_BOOT3), (IEN | PTD | DIS | M4)) /*GPIO_5*/\
+ MUX_VAL(CP(SYS_BOOT4), (IEN | PTD | DIS | M4)) /*GPIO_6*/\
+ MUX_VAL(CP(SYS_BOOT5), (IEN | PTD | DIS | M4)) /*GPIO_7*/\
+ MUX_VAL(CP(SYS_BOOT6), (IDIS | PTD | DIS | M4)) /*GPIO_8*/ \
+ MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)) /*SYS_OFF_MODE*/\
+ MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0)) /*SYS_CLKOUT1*/\
+ MUX_VAL(CP(SYS_CLKOUT2), (IEN | PTU | EN | M4)) /*GPIO_186*/\
+ MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | EN | M3)) /*HSUSB1_STP*/\
+ MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTU | DIS | M3)) /*HSUSB1_CLK*/\
+ MUX_VAL(CP(ETK_D0_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA0*/\
+ MUX_VAL(CP(ETK_D1_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA1*/\
+ MUX_VAL(CP(ETK_D2_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA2*/\
+ MUX_VAL(CP(ETK_D3_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA7*/\
+ MUX_VAL(CP(ETK_D4_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA4*/\
+ MUX_VAL(CP(ETK_D5_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA5*/\
+ MUX_VAL(CP(ETK_D6_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA6*/\
+ MUX_VAL(CP(ETK_D7_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA3*/\
+ MUX_VAL(CP(ETK_D8_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DIR*/\
+ MUX_VAL(CP(ETK_D9_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_NXT*/\
+ MUX_VAL(CP(D2D_MCAD1), (IEN | PTD | EN | M0)) /*d2d_mcad1*/\
+ MUX_VAL(CP(D2D_MCAD2), (IEN | PTD | EN | M0)) /*d2d_mcad2*/\
+ MUX_VAL(CP(D2D_MCAD3), (IEN | PTD | EN | M0)) /*d2d_mcad3*/\
+ MUX_VAL(CP(D2D_MCAD4), (IEN | PTD | EN | M0)) /*d2d_mcad4*/\
+ MUX_VAL(CP(D2D_MCAD5), (IEN | PTD | EN | M0)) /*d2d_mcad5*/\
+ MUX_VAL(CP(D2D_MCAD6), (IEN | PTD | EN | M0)) /*d2d_mcad6*/\
+ MUX_VAL(CP(D2D_MCAD7), (IEN | PTD | EN | M0)) /*d2d_mcad7*/\
+ MUX_VAL(CP(D2D_MCAD8), (IEN | PTD | EN | M0)) /*d2d_mcad8*/\
+ MUX_VAL(CP(D2D_MCAD9), (IEN | PTD | EN | M0)) /*d2d_mcad9*/\
+ MUX_VAL(CP(D2D_MCAD10), (IEN | PTD | EN | M0)) /*d2d_mcad10*/\
+ MUX_VAL(CP(D2D_MCAD11), (IEN | PTD | EN | M0)) /*d2d_mcad11*/\
+ MUX_VAL(CP(D2D_MCAD12), (IEN | PTD | EN | M0)) /*d2d_mcad12*/\
+ MUX_VAL(CP(D2D_MCAD13), (IEN | PTD | EN | M0)) /*d2d_mcad13*/\
+ MUX_VAL(CP(D2D_MCAD14), (IEN | PTD | EN | M0)) /*d2d_mcad14*/\
+ MUX_VAL(CP(D2D_MCAD15), (IEN | PTD | EN | M0)) /*d2d_mcad15*/\
+ MUX_VAL(CP(D2D_MCAD16), (IEN | PTD | EN | M0)) /*d2d_mcad16*/\
+ MUX_VAL(CP(D2D_MCAD17), (IEN | PTD | EN | M0)) /*d2d_mcad17*/\
+ MUX_VAL(CP(D2D_MCAD18), (IEN | PTD | EN | M0)) /*d2d_mcad18*/\
+ MUX_VAL(CP(D2D_MCAD19), (IEN | PTD | EN | M0)) /*d2d_mcad19*/\
+ MUX_VAL(CP(D2D_MCAD20), (IEN | PTD | EN | M0)) /*d2d_mcad20*/\
+ MUX_VAL(CP(D2D_MCAD21), (IEN | PTD | EN | M0)) /*d2d_mcad21*/\
+ MUX_VAL(CP(D2D_MCAD22), (IEN | PTD | EN | M0)) /*d2d_mcad22*/\
+ MUX_VAL(CP(D2D_MCAD23), (IEN | PTD | EN | M0)) /*d2d_mcad23*/\
+ MUX_VAL(CP(D2D_MCAD24), (IEN | PTD | EN | M0)) /*d2d_mcad24*/\
+ MUX_VAL(CP(D2D_MCAD25), (IEN | PTD | EN | M0)) /*d2d_mcad25*/\
+ MUX_VAL(CP(D2D_MCAD26), (IEN | PTD | EN | M0)) /*d2d_mcad26*/\
+ MUX_VAL(CP(D2D_MCAD27), (IEN | PTD | EN | M0)) /*d2d_mcad27*/\
+ MUX_VAL(CP(D2D_MCAD28), (IEN | PTD | EN | M0)) /*d2d_mcad28*/\
+ MUX_VAL(CP(D2D_MCAD29), (IEN | PTD | EN | M0)) /*d2d_mcad29*/\
+ MUX_VAL(CP(D2D_MCAD30), (IEN | PTD | EN | M0)) /*d2d_mcad30*/\
+ MUX_VAL(CP(D2D_MCAD31), (IEN | PTD | EN | M0)) /*d2d_mcad31*/\
+ MUX_VAL(CP(D2D_MCAD32), (IEN | PTD | EN | M0)) /*d2d_mcad32*/\
+ MUX_VAL(CP(D2D_MCAD33), (IEN | PTD | EN | M0)) /*d2d_mcad33*/\
+ MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0)) /*d2d_mcad34*/\
+ MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0)) /*d2d_mcad35*/\
+ MUX_VAL(CP(D2D_MCAD36), (IEN | PTD | EN | M0)) /*d2d_mcad36*/\
+ MUX_VAL(CP(D2D_CLK26MI), (IEN | PTD | DIS | M0)) /*d2d_clk26mi*/\
+ MUX_VAL(CP(D2D_NRESPWRON), (IEN | PTD | EN | M0)) /*d2d_nrespwron*/\
+ MUX_VAL(CP(D2D_NRESWARM), (IEN | PTU | EN | M0)) /*d2d_nreswarm */\
+ MUX_VAL(CP(D2D_ARM9NIRQ), (IEN | PTD | DIS | M0)) /*d2d_arm9nirq */\
+ MUX_VAL(CP(D2D_UMA2P6FIQ), (IEN | PTD | DIS | M0)) /*d2d_uma2p6fiq*/\
+ MUX_VAL(CP(D2D_SPINT), (IEN | PTD | EN | M0)) /*d2d_spint*/\
+ MUX_VAL(CP(D2D_FRINT), (IEN | PTD | EN | M0)) /*d2d_frint*/\
+ MUX_VAL(CP(D2D_DMAREQ0), (IEN | PTD | DIS | M0)) /*d2d_dmareq0*/\
+ MUX_VAL(CP(D2D_DMAREQ1), (IEN | PTD | DIS | M0)) /*d2d_dmareq1*/\
+ MUX_VAL(CP(D2D_DMAREQ2), (IEN | PTD | DIS | M0)) /*d2d_dmareq2*/\
+ MUX_VAL(CP(D2D_DMAREQ3), (IEN | PTD | DIS | M0)) /*d2d_dmareq3*/\
+ MUX_VAL(CP(D2D_N3GTRST), (IEN | PTD | DIS | M0)) /*d2d_n3gtrst*/\
+ MUX_VAL(CP(D2D_N3GTDI), (IEN | PTD | DIS | M0)) /*d2d_n3gtdi*/\
+ MUX_VAL(CP(D2D_N3GTDO), (IEN | PTD | DIS | M0)) /*d2d_n3gtdo*/\
+ MUX_VAL(CP(D2D_N3GTMS), (IEN | PTD | DIS | M0)) /*d2d_n3gtms*/\
+ MUX_VAL(CP(D2D_N3GTCK), (IEN | PTD | DIS | M0)) /*d2d_n3gtck*/\
+ MUX_VAL(CP(D2D_N3GRTCK), (IEN | PTD | DIS | M0)) /*d2d_n3grtck*/\
+ MUX_VAL(CP(D2D_MSTDBY), (IEN | PTU | EN | M0)) /*d2d_mstdby*/\
+ MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0)) /*d2d_swakeup*/\
+ MUX_VAL(CP(D2D_IDLEREQ), (IEN | PTD | DIS | M0)) /*d2d_idlereq*/\
+ MUX_VAL(CP(D2D_IDLEACK), (IEN | PTU | EN | M0)) /*d2d_idleack*/\
+ MUX_VAL(CP(D2D_MWRITE), (IEN | PTD | DIS | M0)) /*d2d_mwrite*/\
+ MUX_VAL(CP(D2D_SWRITE), (IEN | PTD | DIS | M0)) /*d2d_swrite*/\
+ MUX_VAL(CP(D2D_MREAD), (IEN | PTD | DIS | M0)) /*d2d_mread*/\
+ MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0)) /*d2d_sread*/\
+ MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_mbusflag*/\
+ MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_sbusflag*/\
+ MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0)) /*sdrc_cke0*/\
+ MUX_VAL(CP(SDRC_CKE1), (IDIS | PTD | DIS | M7)) /*sdrc_cke1*/
+#endif
--- /dev/null
+#
+# (C) Copyright 2006
+# Texas Instruments, <www.ti.com>
+#
+# Beagle Board uses OMAP3 (ARM-CortexA8) cpu
+# see http://www.ti.com/ for more information on Texas Instruments
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# Physical Address:
+# 8000'0000 (bank0)
+# A000/0000 (bank1)
+# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+
+# For use with external or internal boots.
+TEXT_BASE = 0x80e80000
--- /dev/null
+/*
+ * January 2004 - Changed to support H4 device
+ * Copyright (c) 2004 Texas Instruments
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ cpu/arm_cortexa8/start.o (.text)
+ *(.text)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(.rodata) }
+
+ .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) }
+ __exidx_start = .;
+ .ARM.exidx : { *(.ARM.exidx* .gnu.linkonce.armexidx.*) }
+ __exidx_end = .;
+
+ . = ALIGN(4);
+ .data : { *(.data) }
+
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = ALIGN(4);
+ __bss_start = .;
+ .bss : { *(.bss) }
+ _end = .;
+}
--- /dev/null
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)board/$(VENDOR)/common)
+endif
+
+LIB = $(obj)lib$(VENDOR).a
+
+COBJS-$(CONFIG_OMAP3_BEAGLE) += power.o
+COBJS-$(CONFIG_OMAP3_OVERO) += power.o
+COBJS-$(CONFIG_OMAP3_PANDORA) += power.o
+COBJS-$(CONFIG_OMAP3_ZOOM1) += power.o
+
+COBJS := $(COBJS-y)
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+all: $(LIB)
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+/*
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ * Sunil Kumar <sunilsaini05@gmail.com>
+ * Shashi Ranjan <shashiranjanmca05@gmail.com>
+ *
+ * Derived from Beagle Board and 3430 SDP code by
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <i2c.h>
+
+/******************************************************************************
+ * Routine: power_init_r
+ * Description: Configure power supply
+ *****************************************************************************/
+void power_init_r(void)
+{
+ unsigned char byte;
+
+#ifdef CONFIG_DRIVER_OMAP34XX_I2C
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+#endif
+
+ /*
+ * Configure OMAP3 supply voltages in power management
+ * companion chip.
+ */
+
+ /* set VAUX3 to 2.8V */
+ byte = DEV_GRP_P1;
+ i2c_write(PWRMGT_ADDR_ID4, VAUX3_DEV_GRP, 1, &byte, 1);
+ byte = VAUX3_VSEL_28;
+ i2c_write(PWRMGT_ADDR_ID4, VAUX3_DEDICATED, 1, &byte, 1);
+
+ /* set VPLL2 to 1.8V */
+ byte = DEV_GRP_ALL;
+ i2c_write(PWRMGT_ADDR_ID4, VPLL2_DEV_GRP, 1, &byte, 1);
+ byte = VPLL2_VSEL_18;
+ i2c_write(PWRMGT_ADDR_ID4, VPLL2_DEDICATED, 1, &byte, 1);
+
+ /* set VDAC to 1.8V */
+ byte = DEV_GRP_P1;
+ i2c_write(PWRMGT_ADDR_ID4, VDAC_DEV_GRP, 1, &byte, 1);
+ byte = VDAC_VSEL_18;
+ i2c_write(PWRMGT_ADDR_ID4, VDAC_DEDICATED, 1, &byte, 1);
+
+ /* enable LED */
+ byte = LEDBPWM | LEDAPWM | LEDBON | LEDAON;
+ i2c_write(PWRMGT_ADDR_ID3, LEDEN, 1, &byte, 1);
+}
--- /dev/null
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := evm.o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
--- /dev/null
+#
+# (C) Copyright 2006 - 2008
+# Texas Instruments, <www.ti.com>
+#
+# EVM uses OMAP3 (ARM-CortexA8) cpu
+# see http://www.ti.com/ for more information on Texas Instruments
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# Physical Address:
+# 8000'0000 (bank0)
+# A000/0000 (bank1)
+# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+
+# For use with external or internal boots.
+TEXT_BASE = 0x80e80000
--- /dev/null
+/*
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ * Manikandan Pillai <mani.pillai@ti.com>
+ *
+ * Derived from Beagle Board and 3430 SDP code by
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <i2c.h>
+#include <asm/mach-types.h>
+#include "evm.h"
+
+/******************************************************************************
+ * Routine: board_init
+ * Description: Early hardware init.
+ *****************************************************************************/
+int board_init(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+ /* board id for Linux */
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP3EVM;
+ /* boot param addr */
+ gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+ return 0;
+}
+
+/******************************************************************************
+ * Routine: misc_init_r
+ * Description: Init ethernet (done here so udelay works)
+ *****************************************************************************/
+int misc_init_r(void)
+{
+
+#ifdef CONFIG_DRIVER_OMAP34XX_I2C
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+#endif
+
+#if defined(CONFIG_CMD_NET)
+ setup_net_chip();
+#endif
+
+ return 0;
+}
+
+/******************************************************************************
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ * hardware. Many pins need to be moved from protect to primary
+ * mode.
+ *****************************************************************************/
+void set_muxconf_regs(void)
+{
+ MUX_EVM();
+}
+
+/******************************************************************************
+ * Routine: setup_net_chip
+ * Description: Setting up the configuration GPMC registers specific to the
+ * Ethernet hardware.
+ *****************************************************************************/
+static void setup_net_chip(void)
+{
+ gpio_t *gpio3_base = (gpio_t *)OMAP34XX_GPIO3_BASE;
+ gpmc_csx_t *gpmc_cs6_base = (gpmc_csx_t *)GPMC_CONFIG_CS6_BASE;
+ ctrl_t *ctrl_base = (ctrl_t *)OMAP34XX_CTRL_BASE;
+
+ /* Configure GPMC registers */
+ writel(NET_GPMC_CONFIG1, &gpmc_cs6_base->config1);
+ writel(NET_GPMC_CONFIG2, &gpmc_cs6_base->config2);
+ writel(NET_GPMC_CONFIG3, &gpmc_cs6_base->config3);
+ writel(NET_GPMC_CONFIG4, &gpmc_cs6_base->config4);
+ writel(NET_GPMC_CONFIG5, &gpmc_cs6_base->config5);
+ writel(NET_GPMC_CONFIG6, &gpmc_cs6_base->config6);
+ writel(NET_GPMC_CONFIG7, &gpmc_cs6_base->config7);
+
+ /* Enable off mode for NWE in PADCONF_GPMC_NWE register */
+ writew(readw(&ctrl_base ->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
+ /* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
+ writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
+ /* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
+ writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
+ &ctrl_base->gpmc_nadv_ale);
+
+ /* Make GPIO 64 as output pin */
+ writel(readl(&gpio3_base->oe) & ~(GPIO0), &gpio3_base->oe);
+
+ /* Now send a pulse on the GPIO pin */
+ writel(GPIO0, &gpio3_base->setdataout);
+ udelay(1);
+ writel(GPIO0, &gpio3_base->cleardataout);
+ udelay(1);
+ writel(GPIO0, &gpio3_base->setdataout);
+}
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Nishanth Menon <menon.nishanth@gmail.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _EVM_H_
+#define _EVM_H_
+
+const omap3_sysinfo sysinfo = {
+ OMAP3EVM_V1,
+ OMAP3EVM_V2,
+ DDR_DISCRETE,
+ "35X-Family",
+ "OMAP3 EVM board",
+#if defined(CONFIG_ENV_IS_IN_ONENAND)
+ "OneNAND",
+#else
+ "NAND",
+#endif
+};
+
+static void setup_net_chip(void);
+
+/*
+ * IEN - Input Enable
+ * IDIS - Input Disable
+ * PTD - Pull type Down
+ * PTU - Pull type Up
+ * DIS - Pull type selection is inactive
+ * EN - Pull type selection is active
+ * M0 - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_EVM() \
+ /*SDRC*/\
+ MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) /*SDRC_D0*/\
+ MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /*SDRC_D1*/\
+ MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /*SDRC_D2*/\
+ MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /*SDRC_D3*/\
+ MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /*SDRC_D4*/\
+ MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /*SDRC_D5*/\
+ MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /*SDRC_D6*/\
+ MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /*SDRC_D7*/\
+ MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /*SDRC_D8*/\
+ MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /*SDRC_D9*/\
+ MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /*SDRC_D10*/\
+ MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /*SDRC_D11*/\
+ MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /*SDRC_D12*/\
+ MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /*SDRC_D13*/\
+ MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /*SDRC_D14*/\
+ MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /*SDRC_D15*/\
+ MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /*SDRC_D16*/\
+ MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /*SDRC_D17*/\
+ MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /*SDRC_D18*/\
+ MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /*SDRC_D19*/\
+ MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /*SDRC_D20*/\
+ MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /*SDRC_D21*/\
+ MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /*SDRC_D22*/\
+ MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /*SDRC_D23*/\
+ MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /*SDRC_D24*/\
+ MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /*SDRC_D25*/\
+ MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /*SDRC_D26*/\
+ MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /*SDRC_D27*/\
+ MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /*SDRC_D28*/\
+ MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /*SDRC_D29*/\
+ MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /*SDRC_D30*/\
+ MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /*SDRC_D31*/\
+ MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /*SDRC_CLK*/\
+ MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /*SDRC_DQS0*/\
+ MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /*SDRC_DQS1*/\
+ MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /*SDRC_DQS2*/\
+ MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /*SDRC_DQS3*/\
+ /*GPMC*/\
+ MUX_VAL(CP(GPMC_A1), (IDIS | PTU | EN | M0)) /*GPMC_A1*/\
+ MUX_VAL(CP(GPMC_A2), (IDIS | PTU | EN | M0)) /*GPMC_A2*/\
+ MUX_VAL(CP(GPMC_A3), (IDIS | PTU | EN | M0)) /*GPMC_A3*/\
+ MUX_VAL(CP(GPMC_A4), (IDIS | PTU | EN | M0)) /*GPMC_A4*/\
+ MUX_VAL(CP(GPMC_A5), (IDIS | PTU | EN | M0)) /*GPMC_A5*/\
+ MUX_VAL(CP(GPMC_A6), (IDIS | PTU | EN | M0)) /*GPMC_A6*/\
+ MUX_VAL(CP(GPMC_A7), (IDIS | PTU | EN | M0)) /*GPMC_A7*/\
+ MUX_VAL(CP(GPMC_A8), (IDIS | PTU | EN | M0)) /*GPMC_A8*/\
+ MUX_VAL(CP(GPMC_A9), (IDIS | PTU | EN | M0)) /*GPMC_A9*/\
+ MUX_VAL(CP(GPMC_A10), (IDIS | PTU | EN | M0)) /*GPMC_A10*/\
+ MUX_VAL(CP(GPMC_D0), (IEN | PTU | EN | M0)) /*GPMC_D0*/\
+ MUX_VAL(CP(GPMC_D1), (IEN | PTU | EN | M0)) /*GPMC_D1*/\
+ MUX_VAL(CP(GPMC_D2), (IEN | PTU | EN | M0)) /*GPMC_D2*/\
+ MUX_VAL(CP(GPMC_D3), (IEN | PTU | EN | M0)) /*GPMC_D3*/\
+ MUX_VAL(CP(GPMC_D4), (IEN | PTU | EN | M0)) /*GPMC_D4*/\
+ MUX_VAL(CP(GPMC_D5), (IEN | PTU | EN | M0)) /*GPMC_D5*/\
+ MUX_VAL(CP(GPMC_D6), (IEN | PTU | EN | M0)) /*GPMC_D6*/\
+ MUX_VAL(CP(GPMC_D7), (IEN | PTU | EN | M0)) /*GPMC_D7*/\
+ MUX_VAL(CP(GPMC_D8), (IEN | PTU | EN | M0)) /*GPMC_D8*/\
+ MUX_VAL(CP(GPMC_D9), (IEN | PTU | EN | M0)) /*GPMC_D9*/\
+ MUX_VAL(CP(GPMC_D10), (IEN | PTU | EN | M0)) /*GPMC_D10*/\
+ MUX_VAL(CP(GPMC_D11), (IEN | PTU | EN | M0)) /*GPMC_D11*/\
+ MUX_VAL(CP(GPMC_D12), (IEN | PTU | EN | M0)) /*GPMC_D12*/\
+ MUX_VAL(CP(GPMC_D13), (IEN | PTU | EN | M0)) /*GPMC_D13*/\
+ MUX_VAL(CP(GPMC_D14), (IEN | PTU | EN | M0)) /*GPMC_D14*/\
+ MUX_VAL(CP(GPMC_D15), (IEN | PTU | EN | M0)) /*GPMC_D15*/\
+ MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /*GPMC_nCS0*/\
+ MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M0)) /*GPMC_nCS1*/\
+ MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M0)) /*GPMC_nCS2*/\
+ MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M0)) /*GPMC_nCS3*/\
+ MUX_VAL(CP(GPMC_NCS4), (IEN | PTU | EN | M0)) /*GPMC_nCS4*/\
+ MUX_VAL(CP(GPMC_NCS5), (IDIS | PTU | EN | M0)) /*GPMC_nCS5*/\
+ MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M0)) /*GPMC_nCS6*/\
+ MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M0)) /*GPMC_nCS7*/\
+ MUX_VAL(CP(GPMC_CLK), (IDIS | PTU | EN | M0)) /*GPMC_CLK*/\
+ MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /*GPMC_nADV_ALE*/\
+ MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\
+ MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\
+ MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTU | EN | M0)) /*GPMC_nBE0_CLE*/\
+ MUX_VAL(CP(GPMC_NBE1), (IEN | PTU | EN | M0)) /*GPMC_nBE1*/\
+ MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0)) /*GPMC_nWP*/\
+ MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) /*GPMC_WAIT0*/\
+ MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) /*GPMC_WAIT1*/\
+ MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M4)) /*GPIO_64*/\
+ /* - ETH_nRESET*/\
+ MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) /*GPMC_WAIT3*/\
+ /*DSS*/\
+ MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
+ MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0)) /*DSS_HSYNC*/\
+ MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0)) /*DSS_VSYNC*/\
+ MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0)) /*DSS_ACBIAS*/\
+ MUX_VAL(CP(DSS_DATA0), (IDIS | PTD | DIS | M0)) /*DSS_DATA0*/\
+ MUX_VAL(CP(DSS_DATA1), (IDIS | PTD | DIS | M0)) /*DSS_DATA1*/\
+ MUX_VAL(CP(DSS_DATA2), (IDIS | PTD | DIS | M0)) /*DSS_DATA2*/\
+ MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M0)) /*DSS_DATA3*/\
+ MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M0)) /*DSS_DATA4*/\
+ MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M0)) /*DSS_DATA5*/\
+ MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0)) /*DSS_DATA6*/\
+ MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0)) /*DSS_DATA7*/\
+ MUX_VAL(CP(DSS_DATA8), (IDIS | PTD | DIS | M0)) /*DSS_DATA8*/\
+ MUX_VAL(CP(DSS_DATA9), (IDIS | PTD | DIS | M0)) /*DSS_DATA9*/\
+ MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0)) /*DSS_DATA10*/\
+ MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0)) /*DSS_DATA11*/\
+ MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0)) /*DSS_DATA12*/\
+ MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0)) /*DSS_DATA13*/\
+ MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0)) /*DSS_DATA14*/\
+ MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0)) /*DSS_DATA15*/\
+ MUX_VAL(CP(DSS_DATA16), (IDIS | PTD | DIS | M0)) /*DSS_DATA16*/\
+ MUX_VAL(CP(DSS_DATA17), (IDIS | PTD | DIS | M0)) /*DSS_DATA17*/\
+ MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M0)) /*DSS_DATA18*/\
+ MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0)) /*DSS_DATA19*/\
+ MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0)) /*DSS_DATA20*/\
+ MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0)) /*DSS_DATA21*/\
+ MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0)) /*DSS_DATA22*/\
+ MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0)) /*DSS_DATA23*/\
+ /*CAMERA*/\
+ MUX_VAL(CP(CAM_HS), (IEN | PTU | EN | M0)) /*CAM_HS */\
+ MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M0)) /*CAM_VS */\
+ MUX_VAL(CP(CAM_XCLKA), (IDIS | PTD | DIS | M0)) /*CAM_XCLKA*/\
+ MUX_VAL(CP(CAM_PCLK), (IEN | PTU | EN | M0)) /*CAM_PCLK*/\
+ MUX_VAL(CP(CAM_FLD), (IDIS | PTD | DIS | M4)) /*GPIO_98*/\
+ /* - CAM_RESET*/\
+ MUX_VAL(CP(CAM_D0), (IEN | PTD | DIS | M0)) /*CAM_D0*/\
+ MUX_VAL(CP(CAM_D1), (IEN | PTD | DIS | M0)) /*CAM_D1*/\
+ MUX_VAL(CP(CAM_D2), (IEN | PTD | DIS | M0)) /*CAM_D2*/\
+ MUX_VAL(CP(CAM_D3), (IEN | PTD | DIS | M0)) /*CAM_D3*/\
+ MUX_VAL(CP(CAM_D4), (IEN | PTD | DIS | M0)) /*CAM_D4*/\
+ MUX_VAL(CP(CAM_D5), (IEN | PTD | DIS | M0)) /*CAM_D5*/\
+ MUX_VAL(CP(CAM_D6), (IEN | PTD | DIS | M0)) /*CAM_D6*/\
+ MUX_VAL(CP(CAM_D7), (IEN | PTD | DIS | M0)) /*CAM_D7*/\
+ MUX_VAL(CP(CAM_D8), (IEN | PTD | DIS | M0)) /*CAM_D8*/\
+ MUX_VAL(CP(CAM_D9), (IEN | PTD | DIS | M0)) /*CAM_D9*/\
+ MUX_VAL(CP(CAM_D10), (IEN | PTD | DIS | M0)) /*CAM_D10*/\
+ MUX_VAL(CP(CAM_D11), (IEN | PTD | DIS | M0)) /*CAM_D11*/\
+ MUX_VAL(CP(CAM_XCLKB), (IDIS | PTD | DIS | M0)) /*CAM_XCLKB*/\
+ MUX_VAL(CP(CAM_WEN), (IEN | PTD | DIS | M4)) /*GPIO_167*/\
+ MUX_VAL(CP(CAM_STROBE), (IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
+ MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0)) /*CSI2_DX0*/\
+ MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0)) /*CSI2_DY0*/\
+ MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0)) /*CSI2_DX1*/\
+ MUX_VAL(CP(CSI2_DY1), (IEN | PTD | DIS | M0)) /*CSI2_DY1*/\
+ /*Audio Interface */\
+ MUX_VAL(CP(MCBSP2_FSX), (IEN | PTD | DIS | M0)) /*McBSP2_FSX*/\
+ MUX_VAL(CP(MCBSP2_CLKX), (IEN | PTD | DIS | M0)) /*McBSP2_CLKX*/\
+ MUX_VAL(CP(MCBSP2_DR), (IEN | PTD | DIS | M0)) /*McBSP2_DR*/\
+ MUX_VAL(CP(MCBSP2_DX), (IDIS | PTD | DIS | M0)) /*McBSP2_DX*/\
+ /*Expansion card */\
+ MUX_VAL(CP(MMC1_CLK), (IDIS | PTU | EN | M0)) /*MMC1_CLK*/\
+ MUX_VAL(CP(MMC1_CMD), (IEN | PTU | EN | M0)) /*MMC1_CMD*/\
+ MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | EN | M0)) /*MMC1_DAT0*/\
+ MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | EN | M0)) /*MMC1_DAT1*/\
+ MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | EN | M0)) /*MMC1_DAT2*/\
+ MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | EN | M0)) /*MMC1_DAT3*/\
+ MUX_VAL(CP(MMC1_DAT4), (IEN | PTU | EN | M0)) /*MMC1_DAT4*/\
+ MUX_VAL(CP(MMC1_DAT5), (IEN | PTU | EN | M0)) /*MMC1_DAT5*/\
+ MUX_VAL(CP(MMC1_DAT6), (IEN | PTU | EN | M0)) /*MMC1_DAT6*/\
+ MUX_VAL(CP(MMC1_DAT7), (IEN | PTU | EN | M0)) /*MMC1_DAT7*/\
+ /*Wireless LAN */\
+ MUX_VAL(CP(MMC2_CLK), (IEN | PTD | DIS | M0)) /*MMC2_CLK*/\
+ MUX_VAL(CP(MMC2_CMD), (IEN | PTU | EN | M0)) /*MMC2_CMD*/\
+ MUX_VAL(CP(MMC2_DAT0), (IEN | PTU | EN | M0)) /*MMC2_DAT0*/\
+ MUX_VAL(CP(MMC2_DAT1), (IEN | PTU | EN | M0)) /*MMC2_DAT1*/\
+ MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | EN | M0)) /*MMC2_DAT2*/\
+ MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M0)) /*MMC2_DAT3*/\
+ MUX_VAL(CP(MMC2_DAT4), (IDIS | PTD | DIS | M0)) /*MMC2_DAT4*/\
+ MUX_VAL(CP(MMC2_DAT5), (IDIS | PTD | DIS | M0)) /*MMC2_DAT5*/\
+ MUX_VAL(CP(MMC2_DAT6), (IDIS | PTD | DIS | M0)) /*MMC2_DAT6 */\
+ MUX_VAL(CP(MMC2_DAT7), (IEN | PTU | EN | M0)) /*MMC2_DAT7*/\
+ /*Bluetooth*/\
+ MUX_VAL(CP(MCBSP3_DX), (IDIS | PTD | DIS | M0)) /*McBSP3_DX*/\
+ MUX_VAL(CP(MCBSP3_DR), (IEN | PTD | DIS | M0)) /*McBSP3_DR*/\
+ MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTD | DIS | M0)) /*McBSP3_CLKX */\
+ MUX_VAL(CP(MCBSP3_FSX), (IEN | PTD | DIS | M0)) /*McBSP3_FSX*/\
+ MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M0)) /*UART2_CTS*/\
+ MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M0)) /*UART2_RTS*/\
+ MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M0)) /*UART2_TX*/\
+ MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M0)) /*UART2_RX*/\
+ /*Modem Interface */\
+ MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) /*UART1_TX*/\
+ MUX_VAL(CP(UART1_RTS), (IDIS | PTD | DIS | M0)) /*UART1_RTS*/\
+ MUX_VAL(CP(UART1_CTS), (IEN | PTU | DIS | M0)) /*UART1_CTS*/\
+ MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0)) /*UART1_RX*/\
+ MUX_VAL(CP(MCBSP4_CLKX), (IDIS | PTD | DIS | M4)) /*GPIO_152*/\
+ /* - LCD_INI*/\
+ MUX_VAL(CP(MCBSP4_DR), (IDIS | PTD | DIS | M4)) /*GPIO_153*/\
+ /* - LCD_ENVDD */\
+ MUX_VAL(CP(MCBSP4_DX), (IDIS | PTD | DIS | M4)) /*GPIO_154*/\
+ /* - LCD_QVGA/nVGA */\
+ MUX_VAL(CP(MCBSP4_FSX), (IDIS | PTD | DIS | M4)) /*GPIO_155*/\
+ /* - LCD_RESB */\
+ MUX_VAL(CP(MCBSP1_CLKR), (IEN | PTD | DIS | M0)) /*MCBSP1_CLKR */\
+ MUX_VAL(CP(MCBSP1_FSR), (IDIS | PTU | EN | M0)) /*MCBSP1_FSR*/\
+ MUX_VAL(CP(MCBSP1_DX), (IDIS | PTD | DIS | M0)) /*MCBSP1_DX*/\
+ MUX_VAL(CP(MCBSP1_DR), (IEN | PTD | DIS | M0)) /*MCBSP1_DR*/\
+ MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) /*MCBSP_CLKS */\
+ MUX_VAL(CP(MCBSP1_FSX), (IEN | PTD | DIS | M0)) /*MCBSP1_FSX*/\
+ MUX_VAL(CP(MCBSP1_CLKX), (IEN | PTD | DIS | M0)) /*MCBSP1_CLKX */\
+ /*Serial Interface*/\
+ MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTD | EN | M0)) /*UART3_CTS_*/\
+ /* RCTX*/\
+ MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTD | DIS | M0)) /*UART3_RTS_SD */\
+ MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0)) /*UART3_RX_IRRX*/\
+ MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0)) /*UART3_TX_IRTX*/\
+ MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0)) /*HSUSB0_CLK*/\
+ MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0)) /*HSUSB0_STP*/\
+ MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0)) /*HSUSB0_DIR*/\
+ MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0)) /*HSUSB0_NXT*/\
+ MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA0*/\
+ MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA1*/\
+ MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA2*/\
+ MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA3*/\
+ MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA4*/\
+ MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA5*/\
+ MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA6*/\
+ MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA7*/\
+ MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) /*I2C1_SCL*/\
+ MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) /*I2C1_SDA*/\
+ MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M0)) /*I2C2_SCL*/\
+ MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M0)) /*I2C2_SDA*/\
+ MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0)) /*I2C3_SCL*/\
+ MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0)) /*I2C3_SDA*/\
+ MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0)) /*I2C4_SCL*/\
+ MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0)) /*I2C4_SDA*/\
+ MUX_VAL(CP(HDQ_SIO), (IEN | PTU | EN | M0)) /*HDQ_SIO*/\
+ MUX_VAL(CP(MCSPI1_CLK), (IEN | PTD | DIS | M0)) /*McSPI1_CLK*/\
+ MUX_VAL(CP(MCSPI1_SIMO), (IEN | PTD | DIS | M0)) /*McSPI1_SIMO */\
+ MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M0)) /*McSPI1_SOMI */\
+ MUX_VAL(CP(MCSPI1_CS0), (IEN | PTD | EN | M0)) /*McSPI1_CS0*/\
+ MUX_VAL(CP(MCSPI1_CS1), (IEN | PTD | EN | M4)) /*GPIO_175*/\
+ /* TS_PEN_IRQ */\
+ MUX_VAL(CP(MCSPI1_CS2), (IEN | PTU | DIS | M4)) /*GPIO_176*/\
+ /* - LAN_INTR*/\
+ MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | EN | M0)) /*McSPI1_CS3*/\
+ MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | DIS | M0)) /*McSPI2_CLK*/\
+ MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | DIS | M0)) /*McSPI2_SIMO*/\
+ MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | DIS | M0)) /*McSPI2_SOMI*/\
+ MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | EN | M0)) /*McSPI2_CS0*/\
+ MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | EN | M0)) /*McSPI2_CS1*/\
+ /*Control and debug */\
+ MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)) /*SYS_32K*/\
+ MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) /*SYS_CLKREQ*/\
+ MUX_VAL(CP(SYS_NIRQ), (IEN | PTU | EN | M0)) /*SYS_nIRQ*/\
+ MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) /*GPIO_2*/\
+ /* - PEN_IRQ */\
+ MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) /*GPIO_3 */\
+ MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /*GPIO_4*/\
+ MUX_VAL(CP(SYS_BOOT3), (IEN | PTD | DIS | M4)) /*GPIO_5*/\
+ MUX_VAL(CP(SYS_BOOT4), (IEN | PTD | DIS | M4)) /*GPIO_6*/\
+ MUX_VAL(CP(SYS_BOOT5), (IEN | PTD | DIS | M4)) /*GPIO_7*/\
+ MUX_VAL(CP(SYS_BOOT6), (IDIS | PTD | DIS | M4)) /*GPIO_8*/\
+ /* - VIO_1V8*/\
+ MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)) /*SYS_OFF_MODE*/\
+ MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0)) /*SYS_CLKOUT1*/\
+ MUX_VAL(CP(SYS_CLKOUT2), (IEN | PTU | EN | M0)) /*SYS_CLKOUT2*/\
+ MUX_VAL(CP(JTAG_nTRST), (IEN | PTD | DIS | M0)) /*JTAG_nTRST*/\
+ MUX_VAL(CP(JTAG_TCK), (IEN | PTD | DIS | M0)) /*JTAG_TCK*/\
+ MUX_VAL(CP(JTAG_TMS), (IEN | PTD | DIS | M0)) /*JTAG_TMS*/\
+ MUX_VAL(CP(JTAG_TDI), (IEN | PTD | DIS | M0)) /*JTAG_TDI*/\
+ MUX_VAL(CP(JTAG_EMU0), (IEN | PTD | DIS | M0)) /*JTAG_EMU0*/\
+ MUX_VAL(CP(JTAG_EMU1), (IEN | PTD | DIS | M0)) /*JTAG_EMU1*/\
+ MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | EN | M0)) /*ETK_CLK*/\
+ MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTD | DIS | M0)) /*ETK_CTL*/\
+ MUX_VAL(CP(ETK_D0_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D0*/\
+ MUX_VAL(CP(ETK_D1_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D1*/\
+ MUX_VAL(CP(ETK_D2_ES2 ), (IEN | PTD | EN | M0)) /*ETK_D2*/\
+ MUX_VAL(CP(ETK_D3_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D3*/\
+ MUX_VAL(CP(ETK_D4_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D4*/\
+ MUX_VAL(CP(ETK_D5_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D5*/\
+ MUX_VAL(CP(ETK_D6_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D6*/\
+ MUX_VAL(CP(ETK_D7_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D7*/\
+ MUX_VAL(CP(ETK_D8_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D8*/\
+ MUX_VAL(CP(ETK_D9_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D9*/\
+ MUX_VAL(CP(ETK_D10_ES2), (IEN | PTD | DIS | M0)) /*ETK_D10*/\
+ MUX_VAL(CP(ETK_D11_ES2), (IEN | PTD | DIS | M0)) /*ETK_D11*/\
+ MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M0)) /*ETK_D12*/\
+ MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M0)) /*ETK_D13*/\
+ MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M0)) /*ETK_D14*/\
+ MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | DIS | M0)) /*ETK_D15*/\
+ /*Die to Die */\
+ MUX_VAL(CP(D2D_MCAD1), (IEN | PTD | EN | M0)) /*d2d_mcad1*/\
+ MUX_VAL(CP(D2D_MCAD2), (IEN | PTD | EN | M0)) /*d2d_mcad2*/\
+ MUX_VAL(CP(D2D_MCAD3), (IEN | PTD | EN | M0)) /*d2d_mcad3*/\
+ MUX_VAL(CP(D2D_MCAD4), (IEN | PTD | EN | M0)) /*d2d_mcad4*/\
+ MUX_VAL(CP(D2D_MCAD5), (IEN | PTD | EN | M0)) /*d2d_mcad5*/\
+ MUX_VAL(CP(D2D_MCAD6), (IEN | PTD | EN | M0)) /*d2d_mcad6*/\
+ MUX_VAL(CP(D2D_MCAD7), (IEN | PTD | EN | M0)) /*d2d_mcad7*/\
+ MUX_VAL(CP(D2D_MCAD8), (IEN | PTD | EN | M0)) /*d2d_mcad8*/\
+ MUX_VAL(CP(D2D_MCAD9), (IEN | PTD | EN | M0)) /*d2d_mcad9*/\
+ MUX_VAL(CP(D2D_MCAD10), (IEN | PTD | EN | M0)) /*d2d_mcad10*/\
+ MUX_VAL(CP(D2D_MCAD11), (IEN | PTD | EN | M0)) /*d2d_mcad11*/\
+ MUX_VAL(CP(D2D_MCAD12), (IEN | PTD | EN | M0)) /*d2d_mcad12*/\
+ MUX_VAL(CP(D2D_MCAD13), (IEN | PTD | EN | M0)) /*d2d_mcad13*/\
+ MUX_VAL(CP(D2D_MCAD14), (IEN | PTD | EN | M0)) /*d2d_mcad14*/\
+ MUX_VAL(CP(D2D_MCAD15), (IEN | PTD | EN | M0)) /*d2d_mcad15*/\
+ MUX_VAL(CP(D2D_MCAD16), (IEN | PTD | EN | M0)) /*d2d_mcad16*/\
+ MUX_VAL(CP(D2D_MCAD17), (IEN | PTD | EN | M0)) /*d2d_mcad17*/\
+ MUX_VAL(CP(D2D_MCAD18), (IEN | PTD | EN | M0)) /*d2d_mcad18*/\
+ MUX_VAL(CP(D2D_MCAD19), (IEN | PTD | EN | M0)) /*d2d_mcad19*/\
+ MUX_VAL(CP(D2D_MCAD20), (IEN | PTD | EN | M0)) /*d2d_mcad20*/\
+ MUX_VAL(CP(D2D_MCAD21), (IEN | PTD | EN | M0)) /*d2d_mcad21*/\
+ MUX_VAL(CP(D2D_MCAD22), (IEN | PTD | EN | M0)) /*d2d_mcad22*/\
+ MUX_VAL(CP(D2D_MCAD23), (IEN | PTD | EN | M0)) /*d2d_mcad23*/\
+ MUX_VAL(CP(D2D_MCAD24), (IEN | PTD | EN | M0)) /*d2d_mcad24*/\
+ MUX_VAL(CP(D2D_MCAD25), (IEN | PTD | EN | M0)) /*d2d_mcad25*/\
+ MUX_VAL(CP(D2D_MCAD26), (IEN | PTD | EN | M0)) /*d2d_mcad26*/\
+ MUX_VAL(CP(D2D_MCAD27), (IEN | PTD | EN | M0)) /*d2d_mcad27*/\
+ MUX_VAL(CP(D2D_MCAD28), (IEN | PTD | EN | M0)) /*d2d_mcad28*/\
+ MUX_VAL(CP(D2D_MCAD29), (IEN | PTD | EN | M0)) /*d2d_mcad29*/\
+ MUX_VAL(CP(D2D_MCAD30), (IEN | PTD | EN | M0)) /*d2d_mcad30*/\
+ MUX_VAL(CP(D2D_MCAD31), (IEN | PTD | EN | M0)) /*d2d_mcad31*/\
+ MUX_VAL(CP(D2D_MCAD32), (IEN | PTD | EN | M0)) /*d2d_mcad32*/\
+ MUX_VAL(CP(D2D_MCAD33), (IEN | PTD | EN | M0)) /*d2d_mcad33*/\
+ MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0)) /*d2d_mcad34*/\
+ MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0)) /*d2d_mcad35*/\
+ MUX_VAL(CP(D2D_MCAD36), (IEN | PTD | EN | M0)) /*d2d_mcad36*/\
+ MUX_VAL(CP(D2D_CLK26MI), (IEN | PTD | DIS | M0)) /*d2d_clk26mi*/\
+ MUX_VAL(CP(D2D_NRESPWRON), (IEN | PTD | EN | M0)) /*d2d_nrespwron*/\
+ MUX_VAL(CP(D2D_NRESWARM), (IEN | PTU | EN | M0)) /*d2d_nreswarm */\
+ MUX_VAL(CP(D2D_ARM9NIRQ), (IEN | PTD | DIS | M0)) /*d2d_arm9nirq */\
+ MUX_VAL(CP(D2D_UMA2P6FIQ), (IEN | PTD | DIS | M0)) /*d2d_uma2p6fiq*/\
+ MUX_VAL(CP(D2D_SPINT), (IEN | PTD | EN | M0)) /*d2d_spint*/\
+ MUX_VAL(CP(D2D_FRINT), (IEN | PTD | EN | M0)) /*d2d_frint*/\
+ MUX_VAL(CP(D2D_DMAREQ0), (IEN | PTD | DIS | M0)) /*d2d_dmareq0*/\
+ MUX_VAL(CP(D2D_DMAREQ1), (IEN | PTD | DIS | M0)) /*d2d_dmareq1*/\
+ MUX_VAL(CP(D2D_DMAREQ2), (IEN | PTD | DIS | M0)) /*d2d_dmareq2*/\
+ MUX_VAL(CP(D2D_DMAREQ3), (IEN | PTD | DIS | M0)) /*d2d_dmareq3*/\
+ MUX_VAL(CP(D2D_N3GTRST), (IEN | PTD | DIS | M0)) /*d2d_n3gtrst*/\
+ MUX_VAL(CP(D2D_N3GTDI), (IEN | PTD | DIS | M0)) /*d2d_n3gtdi*/\
+ MUX_VAL(CP(D2D_N3GTDO), (IEN | PTD | DIS | M0)) /*d2d_n3gtdo*/\
+ MUX_VAL(CP(D2D_N3GTMS), (IEN | PTD | DIS | M0)) /*d2d_n3gtms*/\
+ MUX_VAL(CP(D2D_N3GTCK), (IEN | PTD | DIS | M0)) /*d2d_n3gtck*/\
+ MUX_VAL(CP(D2D_N3GRTCK), (IEN | PTD | DIS | M0)) /*d2d_n3grtck*/\
+ MUX_VAL(CP(D2D_MSTDBY), (IEN | PTU | EN | M0)) /*d2d_mstdby*/\
+ MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0)) /*d2d_swakeup*/\
+ MUX_VAL(CP(D2D_IDLEREQ), (IEN | PTD | DIS | M0)) /*d2d_idlereq*/\
+ MUX_VAL(CP(D2D_IDLEACK), (IEN | PTU | EN | M0)) /*d2d_idleack*/\
+ MUX_VAL(CP(D2D_MWRITE), (IEN | PTD | DIS | M0)) /*d2d_mwrite*/\
+ MUX_VAL(CP(D2D_SWRITE), (IEN | PTD | DIS | M0)) /*d2d_swrite*/\
+ MUX_VAL(CP(D2D_MREAD), (IEN | PTD | DIS | M0)) /*d2d_mread*/\
+ MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0)) /*d2d_sread*/\
+ MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_mbusflag*/\
+ MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_sbusflag*/\
+ MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0)) /*sdrc_cke0*/\
+ MUX_VAL(CP(SDRC_CKE1), (IDIS | PTD | DIS | M7)) /*sdrc_cke1*/\
+
+#endif
--- /dev/null
+/*
+ * January 2004 - Changed to support H4 device
+ * Copyright (c) 2004 Texas Instruments
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ cpu/arm_cortexa8/start.o (.text)
+ *(.text)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(.rodata) }
+
+ .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) }
+ __exidx_start = .;
+ .ARM.exidx : { *(.ARM.exidx* .gnu.linkonce.armexidx.*) }
+ __exidx_end = .;
+
+ . = ALIGN(4);
+ .data : { *(.data) }
+
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = ALIGN(4);
+ __bss_start = .;
+ .bss : { *(.bss) }
+ _end = .;
+}
--- /dev/null
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := overo.o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
--- /dev/null
+#
+# Overo uses OMAP3 (ARM-CortexA8) cpu
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# Physical Address:
+# 8000'0000 (bank0)
+# A000/0000 (bank1)
+# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+
+# For use with external or internal boots.
+TEXT_BASE = 0x80e80000
--- /dev/null
+/*
+ * Maintainer : Steve Sakoman <steve@sakoman.com>
+ *
+ * Derived from Beagle Board, 3430 SDP, and OMAP3EVM code by
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ * Sunil Kumar <sunilsaini05@gmail.com>
+ * Shashi Ranjan <shashiranjanmca05@gmail.com>
+ *
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-types.h>
+#include "overo.h"
+
+/******************************************************************************
+ * Routine: board_init
+ * Description: Early hardware init.
+ *****************************************************************************/
+int board_init(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+ /* board id for Linux */
+ gd->bd->bi_arch_number = MACH_TYPE_OVERO;
+ /* boot param addr */
+ gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+ return 0;
+}
+
+/******************************************************************************
+ * Routine: misc_init_r
+ * Description: Configure board specific parts
+ *****************************************************************************/
+int misc_init_r(void)
+{
+ gpio_t *gpio5_base = (gpio_t *)OMAP34XX_GPIO5_BASE;
+ gpio_t *gpio6_base = (gpio_t *)OMAP34XX_GPIO6_BASE;
+
+ power_init_r();
+
+ /* Configure GPIOs to output */
+ writel(~((GPIO10) | GPIO9 | GPIO3 | GPIO2), &gpio6_base->oe);
+ writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
+ GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
+
+ /* Set GPIOs */
+ writel(GPIO10 | GPIO9 | GPIO3 | GPIO2, &gpio6_base->setdataout);
+ writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
+ GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
+
+ return 0;
+}
+
+/******************************************************************************
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ * hardware. Many pins need to be moved from protect to primary
+ * mode.
+ *****************************************************************************/
+void set_muxconf_regs(void)
+{
+ MUX_OVERO();
+}
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Steve Sakoman <steve@sakoman.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _OVERO_H_
+#define _OVERO_H_
+
+const omap3_sysinfo sysinfo = {
+ SDP_3430_V1,
+ SDP_3430_V2,
+ DDR_STACKED,
+ "3503",
+ "Gumstix Overo board",
+#if defined(CONFIG_ENV_IS_IN_ONENAND)
+ "OneNAND",
+#else
+ "NAND",
+#endif
+};
+
+/*
+ * IEN - Input Enable
+ * IDIS - Input Disable
+ * PTD - Pull type Down
+ * PTU - Pull type Up
+ * DIS - Pull type selection is inactive
+ * EN - Pull type selection is active
+ * M0 - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_OVERO() \
+ /*SDRC*/\
+ MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) /*SDRC_D0*/\
+ MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /*SDRC_D1*/\
+ MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /*SDRC_D2*/\
+ MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /*SDRC_D3*/\
+ MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /*SDRC_D4*/\
+ MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /*SDRC_D5*/\
+ MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /*SDRC_D6*/\
+ MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /*SDRC_D7*/\
+ MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /*SDRC_D8*/\
+ MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /*SDRC_D9*/\
+ MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /*SDRC_D10*/\
+ MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /*SDRC_D11*/\
+ MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /*SDRC_D12*/\
+ MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /*SDRC_D13*/\
+ MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /*SDRC_D14*/\
+ MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /*SDRC_D15*/\
+ MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /*SDRC_D16*/\
+ MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /*SDRC_D17*/\
+ MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /*SDRC_D18*/\
+ MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /*SDRC_D19*/\
+ MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /*SDRC_D20*/\
+ MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /*SDRC_D21*/\
+ MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /*SDRC_D22*/\
+ MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /*SDRC_D23*/\
+ MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /*SDRC_D24*/\
+ MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /*SDRC_D25*/\
+ MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /*SDRC_D26*/\
+ MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /*SDRC_D27*/\
+ MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /*SDRC_D28*/\
+ MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /*SDRC_D29*/\
+ MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /*SDRC_D30*/\
+ MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /*SDRC_D31*/\
+ MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /*SDRC_CLK*/\
+ MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /*SDRC_DQS0*/\
+ MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /*SDRC_DQS1*/\
+ MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /*SDRC_DQS2*/\
+ MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /*SDRC_DQS3*/\
+ /*GPMC*/\
+ MUX_VAL(CP(GPMC_A1), (IDIS | PTD | DIS | M0)) /*GPMC_A1*/\
+ MUX_VAL(CP(GPMC_A2), (IDIS | PTD | DIS | M0)) /*GPMC_A2*/\
+ MUX_VAL(CP(GPMC_A3), (IDIS | PTD | DIS | M0)) /*GPMC_A3*/\
+ MUX_VAL(CP(GPMC_A4), (IDIS | PTD | DIS | M0)) /*GPMC_A4*/\
+ MUX_VAL(CP(GPMC_A5), (IDIS | PTD | DIS | M0)) /*GPMC_A5*/\
+ MUX_VAL(CP(GPMC_A6), (IDIS | PTD | DIS | M0)) /*GPMC_A6*/\
+ MUX_VAL(CP(GPMC_A7), (IDIS | PTD | DIS | M0)) /*GPMC_A7*/\
+ MUX_VAL(CP(GPMC_A8), (IDIS | PTD | DIS | M0)) /*GPMC_A8*/\
+ MUX_VAL(CP(GPMC_A9), (IDIS | PTD | DIS | M0)) /*GPMC_A9*/\
+ MUX_VAL(CP(GPMC_A10), (IDIS | PTD | DIS | M0)) /*GPMC_A10*/\
+ MUX_VAL(CP(GPMC_D0), (IEN | PTD | DIS | M0)) /*GPMC_D0*/\
+ MUX_VAL(CP(GPMC_D1), (IEN | PTD | DIS | M0)) /*GPMC_D1*/\
+ MUX_VAL(CP(GPMC_D2), (IEN | PTD | DIS | M0)) /*GPMC_D2*/\
+ MUX_VAL(CP(GPMC_D3), (IEN | PTD | DIS | M0)) /*GPMC_D3*/\
+ MUX_VAL(CP(GPMC_D4), (IEN | PTD | DIS | M0)) /*GPMC_D4*/\
+ MUX_VAL(CP(GPMC_D5), (IEN | PTD | DIS | M0)) /*GPMC_D5*/\
+ MUX_VAL(CP(GPMC_D6), (IEN | PTD | DIS | M0)) /*GPMC_D6*/\
+ MUX_VAL(CP(GPMC_D7), (IEN | PTD | DIS | M0)) /*GPMC_D7*/\
+ MUX_VAL(CP(GPMC_D8), (IEN | PTD | DIS | M0)) /*GPMC_D8*/\
+ MUX_VAL(CP(GPMC_D9), (IEN | PTD | DIS | M0)) /*GPMC_D9*/\
+ MUX_VAL(CP(GPMC_D10), (IEN | PTD | DIS | M0)) /*GPMC_D10*/\
+ MUX_VAL(CP(GPMC_D11), (IEN | PTD | DIS | M0)) /*GPMC_D11*/\
+ MUX_VAL(CP(GPMC_D12), (IEN | PTD | DIS | M0)) /*GPMC_D12*/\
+ MUX_VAL(CP(GPMC_D13), (IEN | PTD | DIS | M0)) /*GPMC_D13*/\
+ MUX_VAL(CP(GPMC_D14), (IEN | PTD | DIS | M0)) /*GPMC_D14*/\
+ MUX_VAL(CP(GPMC_D15), (IEN | PTD | DIS | M0)) /*GPMC_D15*/\
+ MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /*GPMC_nCS0*/\
+ MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M0)) /*GPMC_nCS1*/\
+ MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M0)) /*GPMC_nCS2*/\
+ MUX_VAL(CP(GPMC_NCS3), (IEN | PTU | EN | M4)) /*GPIO_54*/\
+ /* - MMC1_WP*/\
+ MUX_VAL(CP(GPMC_NCS4), (IDIS | PTU | EN | M0)) /*GPMC_nCS4*/\
+ MUX_VAL(CP(GPMC_NCS5), (IDIS | PTD | DIS | M0)) /*GPMC_nCS5*/\
+ MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M0)) /*GPMC_nCS6*/\
+ MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M0)) /*GPMC_nCS7*/\
+ MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | DIS | M0)) /*GPMC_nCS3*/\
+ MUX_VAL(CP(GPMC_CLK), (IDIS | PTD | DIS | M0)) /*GPMC_CLK*/\
+ MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /*GPMC_nADV_ALE*/\
+ MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\
+ MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\
+ MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTD | DIS | M0)) /*GPMC_nBE0_CLE*/\
+ MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0)) /*GPMC_nWP*/\
+ MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) /*GPMC_WAIT0*/\
+ MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) /*GPMC_WAIT1*/\
+ MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M0)) /*GPMC_nCS3*/\
+ MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) /*GPMC_nCS3*/\
+ /*DSS*/\
+ MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
+ MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0)) /*DSS_HSYNC*/\
+ MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0)) /*DSS_VSYNC*/\
+ MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0)) /*DSS_ACBIAS*/\
+ MUX_VAL(CP(DSS_DATA0), (IDIS | PTD | DIS | M0)) /*DSS_DATA0*/\
+ MUX_VAL(CP(DSS_DATA1), (IDIS | PTD | DIS | M0)) /*DSS_DATA1*/\
+ MUX_VAL(CP(DSS_DATA2), (IDIS | PTD | DIS | M0)) /*DSS_DATA2*/\
+ MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M0)) /*DSS_DATA3*/\
+ MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M0)) /*DSS_DATA4*/\
+ MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M0)) /*DSS_DATA5*/\
+ MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0)) /*DSS_DATA6*/\
+ MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0)) /*DSS_DATA7*/\
+ MUX_VAL(CP(DSS_DATA8), (IDIS | PTD | DIS | M0)) /*DSS_DATA8*/\
+ MUX_VAL(CP(DSS_DATA9), (IDIS | PTD | DIS | M0)) /*DSS_DATA9*/\
+ MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0)) /*DSS_DATA10*/\
+ MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0)) /*DSS_DATA11*/\
+ MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0)) /*DSS_DATA12*/\
+ MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0)) /*DSS_DATA13*/\
+ MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0)) /*DSS_DATA14*/\
+ MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0)) /*DSS_DATA15*/\
+ MUX_VAL(CP(DSS_DATA16), (IDIS | PTD | DIS | M0)) /*DSS_DATA16*/\
+ MUX_VAL(CP(DSS_DATA17), (IDIS | PTD | DIS | M0)) /*DSS_DATA17*/\
+ MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M0)) /*DSS_DATA18*/\
+ MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0)) /*DSS_DATA19*/\
+ MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0)) /*DSS_DATA20*/\
+ MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0)) /*DSS_DATA21*/\
+ MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0)) /*DSS_DATA22*/\
+ MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0)) /*DSS_DATA23*/\
+ /*CAMERA*/\
+ MUX_VAL(CP(CAM_HS), (IEN | PTU | EN | M0)) /*CAM_HS */\
+ MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M0)) /*CAM_VS */\
+ MUX_VAL(CP(CAM_XCLKA), (IDIS | PTD | DIS | M0)) /*CAM_XCLKA*/\
+ MUX_VAL(CP(CAM_PCLK), (IEN | PTU | EN | M0)) /*CAM_PCLK*/\
+ MUX_VAL(CP(CAM_FLD), (IDIS | PTD | DIS | M4)) /*CAM_FLD*/\
+ MUX_VAL(CP(CAM_D0), (IEN | PTD | DIS | M0)) /*CAM_D0*/\
+ MUX_VAL(CP(CAM_D1), (IEN | PTD | DIS | M0)) /*CAM_D1*/\
+ MUX_VAL(CP(CAM_D2), (IEN | PTD | DIS | M0)) /*CAM_D2*/\
+ MUX_VAL(CP(CAM_D3), (IEN | PTD | DIS | M0)) /*CAM_D3*/\
+ MUX_VAL(CP(CAM_D4), (IEN | PTD | DIS | M0)) /*CAM_D4*/\
+ MUX_VAL(CP(CAM_D5), (IEN | PTD | DIS | M0)) /*CAM_D5*/\
+ MUX_VAL(CP(CAM_D6), (IEN | PTD | DIS | M0)) /*CAM_D6*/\
+ MUX_VAL(CP(CAM_D7), (IEN | PTD | DIS | M0)) /*CAM_D7*/\
+ MUX_VAL(CP(CAM_D8), (IEN | PTD | DIS | M0)) /*CAM_D8*/\
+ MUX_VAL(CP(CAM_D9), (IEN | PTD | DIS | M0)) /*CAM_D9*/\
+ MUX_VAL(CP(CAM_D10), (IEN | PTD | DIS | M0)) /*CAM_D10*/\
+ MUX_VAL(CP(CAM_D11), (IEN | PTD | DIS | M0)) /*CAM_D11*/\
+ MUX_VAL(CP(CAM_XCLKB), (IDIS | PTD | DIS | M0)) /*CAM_XCLKB*/\
+ MUX_VAL(CP(CAM_WEN), (IEN | PTD | DIS | M0)) /*CAM_WEN*/\
+ MUX_VAL(CP(CAM_STROBE), (IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
+ MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0)) /*CSI2_DX0*/\
+ MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0)) /*CSI2_DY0*/\
+ MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0)) /*CSI2_DX1*/\
+ MUX_VAL(CP(CSI2_DY1), (IEN | PTU | EN | M4)) /*GPIO_115*/\
+ /*Audio Interface */\
+ MUX_VAL(CP(MCBSP2_FSX), (IEN | PTD | DIS | M0)) /*McBSP2_FSX*/\
+ MUX_VAL(CP(MCBSP2_CLKX), (IEN | PTD | DIS | M0)) /*McBSP2_CLKX*/\
+ MUX_VAL(CP(MCBSP2_DR), (IEN | PTD | DIS | M0)) /*McBSP2_DR*/\
+ MUX_VAL(CP(MCBSP2_DX), (IDIS | PTD | DIS | M0)) /*McBSP2_DX*/\
+ /*Expansion card */\
+ MUX_VAL(CP(MMC1_CLK), (IDIS | PTU | EN | M0)) /*MMC1_CLK*/\
+ MUX_VAL(CP(MMC1_CMD), (IEN | PTU | EN | M0)) /*MMC1_CMD*/\
+ MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | EN | M0)) /*MMC1_DAT0*/\
+ MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | EN | M0)) /*MMC1_DAT1*/\
+ MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | EN | M0)) /*MMC1_DAT2*/\
+ MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | EN | M0)) /*MMC1_DAT3*/\
+ MUX_VAL(CP(MMC1_DAT4), (IEN | PTU | EN | M0)) /*MMC1_DAT4*/\
+ MUX_VAL(CP(MMC1_DAT5), (IEN | PTU | EN | M0)) /*MMC1_DAT5*/\
+ MUX_VAL(CP(MMC1_DAT6), (IEN | PTU | EN | M0)) /*MMC1_DAT6*/\
+ MUX_VAL(CP(MMC1_DAT7), (IEN | PTU | EN | M0)) /*MMC1_DAT7*/\
+ /*Wireless LAN */\
+ MUX_VAL(CP(MMC2_CLK), (IEN | PTU | EN | M0)) /*MMC2_CLK*/\
+ MUX_VAL(CP(MMC2_CMD), (IEN | PTU | EN | M0)) /*MMC2_CMD*/\
+ MUX_VAL(CP(MMC2_DAT0), (IEN | PTU | EN | M0)) /*MMC2_DAT0*/\
+ MUX_VAL(CP(MMC2_DAT1), (IEN | PTU | EN | M0)) /*MMC2_DAT1*/\
+ MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | EN | M0)) /*MMC2_DAT2*/\
+ MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M0)) /*MMC2_DAT3*/\
+ MUX_VAL(CP(MMC2_DAT4), (IEN | PTU | EN | M1)) /*MMC2_DIR_DAT0*/\
+ MUX_VAL(CP(MMC2_DAT5), (IEN | PTU | EN | M1)) /*MMC2_DIR_DAT1*/\
+ MUX_VAL(CP(MMC2_DAT6), (IEN | PTU | EN | M1)) /*MMC2_DIR_CMD*/\
+ MUX_VAL(CP(MMC2_DAT7), (IEN | PTU | EN | M1)) /*MMC2_CLKIN*/\
+ /*Bluetooth*/\
+ MUX_VAL(CP(MCBSP3_DX), (IEN | PTD | DIS | M1)) /*UART2_CTS*/\
+ MUX_VAL(CP(MCBSP3_DR), (IDIS | PTD | DIS | M1)) /*UART2_RTS*/\
+ MUX_VAL(CP(MCBSP3_CLKX), (IDIS | PTD | DIS | M1)) /*UART2_TX*/\
+ MUX_VAL(CP(MCBSP3_FSX), (IEN | PTD | DIS | M1)) /*UART2_RX*/\
+ MUX_VAL(CP(UART2_CTS), (IDIS | PTD | DIS | M4)) /*GPIO_144 - LCD_EN*/\
+ MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M4)) /*GPIO_145*/\
+ MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M4)) /*GPIO_146*/\
+ MUX_VAL(CP(UART2_RX), (IDIS | PTD | DIS | M4)) /*GPIO_147*/\
+ MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) /*UART1_TX*/\
+ MUX_VAL(CP(UART1_RTS), (IEN | PTU | DIS | M4)) /*GPIO_149*/ \
+ MUX_VAL(CP(UART1_CTS), (IEN | PTU | DIS | M4)) /*GPIO_150-MMC3_WP*/\
+ MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0)) /*UART1_RX*/\
+ MUX_VAL(CP(MCBSP4_CLKX), (IEN | PTD | DIS | M0)) /*McBSP4_CLKX*/\
+ MUX_VAL(CP(MCBSP4_DR), (IEN | PTD | DIS | M0)) /*McBSP4_DR*/\
+ MUX_VAL(CP(MCBSP4_DX), (IEN | PTD | DIS | M0)) /*McBSP4_DX*/\
+ MUX_VAL(CP(MCBSP4_FSX), (IEN | PTD | DIS | M0)) /*McBSP4_FSX*/\
+ MUX_VAL(CP(MCBSP1_CLKR), (IEN | PTD | DIS | M0)) /*McBSP1_CLKR*/\
+ MUX_VAL(CP(MCBSP1_FSR), (IEN | PTD | DIS | M0)) /*McBSP1_FSR*/\
+ MUX_VAL(CP(MCBSP1_DX), (IEN | PTD | DIS | M0)) /*McBSP1_DX*/\
+ MUX_VAL(CP(MCBSP1_DR), (IEN | PTD | DIS | M0)) /*McBSP1_DR*/\
+ MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) /*McBSP_CLKS*/\
+ MUX_VAL(CP(MCBSP1_FSX), (IEN | PTD | DIS | M0)) /*McBSP1_FSX*/\
+ MUX_VAL(CP(MCBSP1_CLKX), (IEN | PTD | DIS | M0)) /*McBSP1_CLKX*/\
+ /*Serial Interface*/\
+ MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTD | EN | M0)) /*UART3_CTS_RCTX*/\
+ MUX_VAL(CP(UART3_RTS_SD), (IEN | PTU | EN | M4)) /*GPIO_164 W2W_*/\
+ /* BT_NRESET*/\
+ MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTU | EN | M0)) /*UART3_RX_IRRX*/\
+ MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0)) /*UART3_TX_IRTX*/\
+ MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0)) /*HSUSB0_CLK*/\
+ MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0)) /*HSUSB0_STP*/\
+ MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0)) /*HSUSB0_DIR*/\
+ MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0)) /*HSUSB0_NXT*/\
+ MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA0*/\
+ MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA1*/\
+ MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA2*/\
+ MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA3*/\
+ MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA4*/\
+ MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA5*/\
+ MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA6*/\
+ MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA7*/\
+ MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) /*I2C1_SCL*/\
+ MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) /*I2C1_SDA*/\
+ MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M4)) /*GPIO_168*/\
+ /* - USBH_CPEN*/\
+ MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M4)) /*GPIO_183*/\
+ /* - USBH_RESET*/\
+ MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0)) /*I2C3_SCL*/\
+ MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0)) /*I2C3_SDA*/\
+ MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0)) /*I2C4_SCL*/\
+ MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0)) /*I2C4_SDA*/\
+ MUX_VAL(CP(HDQ_SIO), (IDIS | PTU | EN | M4)) /*HDQ_SIO*/\
+ MUX_VAL(CP(MCSPI1_CLK), (IEN | PTD | DIS | M0)) /*McSPI1_CLK*/\
+ MUX_VAL(CP(MCSPI1_SIMO), (IEN | PTD | DIS | M0)) /*McSPI1_SIMO */\
+ MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M0)) /*McSPI1_SOMI */\
+ MUX_VAL(CP(MCSPI1_CS0), (IEN | PTD | EN | M0)) /*McSPI1_CS0*/\
+ MUX_VAL(CP(MCSPI1_CS1), (IDIS | PTD | EN | M0)) /*McSPI1_CS1*/\
+ MUX_VAL(CP(MCSPI1_CS2), (IDIS | PTD | DIS | M4)) /*GPIO_176*/\
+ MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA2*/\
+ MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA7*/\
+ MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA4*/\
+ MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA5*/\
+ MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA6*/\
+ MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA3*/\
+ /*Control and debug */\
+ MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)) /*SYS_32K*/\
+ MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) /*SYS_CLKREQ*/\
+ MUX_VAL(CP(SYS_NIRQ), (IEN | PTU | EN | M0)) /*SYS_nIRQ*/\
+ MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) /*GPIO_2*/\
+ MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) /*GPIO_3 */\
+ MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /*GPIO_4 - MMC1_WP*/\
+ MUX_VAL(CP(SYS_BOOT3), (IEN | PTD | DIS | M4)) /*GPIO_5*/\
+ MUX_VAL(CP(SYS_BOOT4), (IEN | PTD | DIS | M4)) /*GPIO_6*/\
+ MUX_VAL(CP(SYS_BOOT5), (IEN | PTD | DIS | M4)) /*GPIO_7*/\
+ MUX_VAL(CP(SYS_BOOT6), (IDIS | PTD | DIS | M4)) /*GPIO_8*/\
+ MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)) /*SYS_OFF_MODE*/\
+ MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0)) /*SYS_CLKOUT1*/\
+ MUX_VAL(CP(SYS_CLKOUT2), (IEN | PTU | EN | M4)) /*GPIO_186*/\
+ MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | EN | M2)) /*MMC3_CLK*/\
+ MUX_VAL(CP(ETK_CTL_ES2), (IEN | PTU | EN | M2)) /*MMC3_CMD*/\
+ MUX_VAL(CP(ETK_D0_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT4*/\
+ MUX_VAL(CP(ETK_D1_ES2), (IEN | PTD | EN | M4)) /*GPIO_15 - X_GATE*/\
+ MUX_VAL(CP(ETK_D2_ES2), (IEN | PTU | EN | M4)) /*GPIO_16*/\
+ /* - W2W_NRESET*/\
+ MUX_VAL(CP(ETK_D3_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT3*/\
+ MUX_VAL(CP(ETK_D4_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT0*/\
+ MUX_VAL(CP(ETK_D5_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT1*/\
+ MUX_VAL(CP(ETK_D6_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT2*/\
+ MUX_VAL(CP(ETK_D7_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT7*/\
+ MUX_VAL(CP(ETK_D8_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT6*/\
+ MUX_VAL(CP(ETK_D9_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT5*/\
+ MUX_VAL(CP(ETK_D10_ES2), (IDIS | PTD | DIS | M3)) /*HSUSB2_CLK*/\
+ MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTU | EN | M3)) /*HSUSB2_STP*/\
+ MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M3)) /*HSUSB2_DIR*/\
+ MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M3)) /*HSUSB2_NXT*/\
+ MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA0*/\
+ MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA1*/\
+ /* die to die */\
+ MUX_VAL(CP(D2D_MCAD1), (IEN | PTD | EN | M0)) /*d2d_mcad1*/\
+ MUX_VAL(CP(D2D_MCAD2), (IEN | PTD | EN | M0)) /*d2d_mcad2*/\
+ MUX_VAL(CP(D2D_MCAD3), (IEN | PTD | EN | M0)) /*d2d_mcad3*/\
+ MUX_VAL(CP(D2D_MCAD4), (IEN | PTD | EN | M0)) /*d2d_mcad4*/\
+ MUX_VAL(CP(D2D_MCAD5), (IEN | PTD | EN | M0)) /*d2d_mcad5*/\
+ MUX_VAL(CP(D2D_MCAD6), (IEN | PTD | EN | M0)) /*d2d_mcad6*/\
+ MUX_VAL(CP(D2D_MCAD7), (IEN | PTD | EN | M0)) /*d2d_mcad7*/\
+ MUX_VAL(CP(D2D_MCAD8), (IEN | PTD | EN | M0)) /*d2d_mcad8*/\
+ MUX_VAL(CP(D2D_MCAD9), (IEN | PTD | EN | M0)) /*d2d_mcad9*/\
+ MUX_VAL(CP(D2D_MCAD10), (IEN | PTD | EN | M0)) /*d2d_mcad10*/\
+ MUX_VAL(CP(D2D_MCAD11), (IEN | PTD | EN | M0)) /*d2d_mcad11*/\
+ MUX_VAL(CP(D2D_MCAD12), (IEN | PTD | EN | M0)) /*d2d_mcad12*/\
+ MUX_VAL(CP(D2D_MCAD13), (IEN | PTD | EN | M0)) /*d2d_mcad13*/\
+ MUX_VAL(CP(D2D_MCAD14), (IEN | PTD | EN | M0)) /*d2d_mcad14*/\
+ MUX_VAL(CP(D2D_MCAD15), (IEN | PTD | EN | M0)) /*d2d_mcad15*/\
+ MUX_VAL(CP(D2D_MCAD16), (IEN | PTD | EN | M0)) /*d2d_mcad16*/\
+ MUX_VAL(CP(D2D_MCAD17), (IEN | PTD | EN | M0)) /*d2d_mcad17*/\
+ MUX_VAL(CP(D2D_MCAD18), (IEN | PTD | EN | M0)) /*d2d_mcad18*/\
+ MUX_VAL(CP(D2D_MCAD19), (IEN | PTD | EN | M0)) /*d2d_mcad19*/\
+ MUX_VAL(CP(D2D_MCAD20), (IEN | PTD | EN | M0)) /*d2d_mcad20*/\
+ MUX_VAL(CP(D2D_MCAD21), (IEN | PTD | EN | M0)) /*d2d_mcad21*/\
+ MUX_VAL(CP(D2D_MCAD22), (IEN | PTD | EN | M0)) /*d2d_mcad22*/\
+ MUX_VAL(CP(D2D_MCAD23), (IEN | PTD | EN | M0)) /*d2d_mcad23*/\
+ MUX_VAL(CP(D2D_MCAD24), (IEN | PTD | EN | M0)) /*d2d_mcad24*/\
+ MUX_VAL(CP(D2D_MCAD25), (IEN | PTD | EN | M0)) /*d2d_mcad25*/\
+ MUX_VAL(CP(D2D_MCAD26), (IEN | PTD | EN | M0)) /*d2d_mcad26*/\
+ MUX_VAL(CP(D2D_MCAD27), (IEN | PTD | EN | M0)) /*d2d_mcad27*/\
+ MUX_VAL(CP(D2D_MCAD28), (IEN | PTD | EN | M0)) /*d2d_mcad28*/\
+ MUX_VAL(CP(D2D_MCAD29), (IEN | PTD | EN | M0)) /*d2d_mcad29*/\
+ MUX_VAL(CP(D2D_MCAD30), (IEN | PTD | EN | M0)) /*d2d_mcad30*/\
+ MUX_VAL(CP(D2D_MCAD31), (IEN | PTD | EN | M0)) /*d2d_mcad31*/\
+ MUX_VAL(CP(D2D_MCAD32), (IEN | PTD | EN | M0)) /*d2d_mcad32*/\
+ MUX_VAL(CP(D2D_MCAD33), (IEN | PTD | EN | M0)) /*d2d_mcad33*/\
+ MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0)) /*d2d_mcad34*/\
+ MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0)) /*d2d_mcad35*/\
+ MUX_VAL(CP(D2D_MCAD36), (IEN | PTD | EN | M0)) /*d2d_mcad36*/\
+ MUX_VAL(CP(D2D_CLK26MI), (IEN | PTD | DIS | M0)) /*d2d_clk26mi*/\
+ MUX_VAL(CP(D2D_NRESPWRON), (IEN | PTD | EN | M0)) /*d2d_nrespwron*/\
+ MUX_VAL(CP(D2D_NRESWARM), (IEN | PTU | EN | M0)) /*d2d_nreswarm */\
+ MUX_VAL(CP(D2D_ARM9NIRQ), (IEN | PTD | DIS | M0)) /*d2d_arm9nirq */\
+ MUX_VAL(CP(D2D_UMA2P6FIQ), (IEN | PTD | DIS | M0)) /*d2d_uma2p6fiq*/\
+ MUX_VAL(CP(D2D_SPINT), (IEN | PTD | EN | M0)) /*d2d_spint*/\
+ MUX_VAL(CP(D2D_FRINT), (IEN | PTD | EN | M0)) /*d2d_frint*/\
+ MUX_VAL(CP(D2D_DMAREQ0), (IEN | PTD | DIS | M0)) /*d2d_dmareq0*/\
+ MUX_VAL(CP(D2D_DMAREQ1), (IEN | PTD | DIS | M0)) /*d2d_dmareq1*/\
+ MUX_VAL(CP(D2D_DMAREQ2), (IEN | PTD | DIS | M0)) /*d2d_dmareq2*/\
+ MUX_VAL(CP(D2D_DMAREQ3), (IEN | PTD | DIS | M0)) /*d2d_dmareq3*/\
+ MUX_VAL(CP(D2D_N3GTRST), (IEN | PTD | DIS | M0)) /*d2d_n3gtrst*/\
+ MUX_VAL(CP(D2D_N3GTDI), (IEN | PTD | DIS | M0)) /*d2d_n3gtdi*/\
+ MUX_VAL(CP(D2D_N3GTDO), (IEN | PTD | DIS | M0)) /*d2d_n3gtdo*/\
+ MUX_VAL(CP(D2D_N3GTMS), (IEN | PTD | DIS | M0)) /*d2d_n3gtms*/\
+ MUX_VAL(CP(D2D_N3GTCK), (IEN | PTD | DIS | M0)) /*d2d_n3gtck*/\
+ MUX_VAL(CP(D2D_N3GRTCK), (IEN | PTD | DIS | M0)) /*d2d_n3grtck*/\
+ MUX_VAL(CP(D2D_MSTDBY), (IEN | PTU | EN | M0)) /*d2d_mstdby*/\
+ MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0)) /*d2d_swakeup*/\
+ MUX_VAL(CP(D2D_IDLEREQ), (IEN | PTD | DIS | M0)) /*d2d_idlereq*/\
+ MUX_VAL(CP(D2D_IDLEACK), (IEN | PTU | EN | M0)) /*d2d_idleack*/\
+ MUX_VAL(CP(D2D_MWRITE), (IEN | PTD | DIS | M0)) /*d2d_mwrite*/\
+ MUX_VAL(CP(D2D_SWRITE), (IEN | PTD | DIS | M0)) /*d2d_swrite*/\
+ MUX_VAL(CP(D2D_MREAD), (IEN | PTD | DIS | M0)) /*d2d_mread*/\
+ MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0)) /*d2d_sread*/\
+ MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_mbusflag*/\
+ MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_sbusflag*/\
+ MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0)) /*sdrc_cke0*/\
+ MUX_VAL(CP(SDRC_CKE1), (IDIS | PTD | DIS | M7)) /*sdrc_cke1*/
+
+#endif
--- /dev/null
+/*
+ * January 2004 - Changed to support H4 device
+ * Copyright (c) 2004 Texas Instruments
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ cpu/arm_cortexa8/start.o (.text)
+ *(.text)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(.rodata) }
+
+ .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) }
+ __exidx_start = .;
+ .ARM.exidx : { *(.ARM.exidx* .gnu.linkonce.armexidx.*) }
+ __exidx_end = .;
+
+ . = ALIGN(4);
+ .data : { *(.data) }
+
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = ALIGN(4);
+ __bss_start = .;
+ .bss : { *(.bss) }
+ _end = .;
+}
--- /dev/null
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := pandora.o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+#
+# (C) Copyright 2006
+# Texas Instruments, <www.ti.com>
+#
+# Pandora uses OMAP3 (ARM-CortexA8) cpu
+# see http://www.ti.com/ for more information on Texas Instruments
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# Physical Address:
+# 8000'0000 (bank0)
+# A000/0000 (bank1)
+# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+
+# For use with external or internal boots.
+TEXT_BASE = 0x80e80000
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Grazvydas Ignotas <notasas@gmail.com>
+ *
+ * Derived from Beagle Board, 3430 SDP, and OMAP3EVM code by
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ * Sunil Kumar <sunilsaini05@gmail.com>
+ * Shashi Ranjan <shashiranjanmca05@gmail.com>
+ *
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-types.h>
+#include "pandora.h"
+
+/******************************************************************************
+ * Routine: board_init
+ * Description: Early hardware init.
+ *****************************************************************************/
+int board_init(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+ /* board id for Linux */
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP3_PANDORA;
+ /* boot param addr */
+ gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+ return 0;
+}
+
+/******************************************************************************
+ * Routine: misc_init_r
+ * Description: Configure board specific parts
+ *****************************************************************************/
+int misc_init_r(void)
+{
+ gpio_t *gpio1_base = (gpio_t *)OMAP34XX_GPIO1_BASE;
+ gpio_t *gpio4_base = (gpio_t *)OMAP34XX_GPIO4_BASE;
+ gpio_t *gpio5_base = (gpio_t *)OMAP34XX_GPIO5_BASE;
+ gpio_t *gpio6_base = (gpio_t *)OMAP34XX_GPIO6_BASE;
+
+ power_init_r();
+
+ /* Configure GPIOs to output */
+ writel(~(GPIO14 | GPIO15 | GPIO16 | GPIO23), &gpio1_base->oe);
+ writel(~GPIO22, &gpio4_base->oe); /* 118 */
+ writel(~(GPIO0 | GPIO1 | GPIO28 | GPIO29 | GPIO30 | GPIO31),
+ &gpio5_base->oe); /* 128, 129, 156-159 */
+ writel(~GPIO4, &gpio6_base->oe); /* 164 */
+
+ /* Set GPIOs */
+ writel(GPIO28, &gpio5_base->setdataout);
+ writel(GPIO4, &gpio6_base->setdataout);
+
+ return 0;
+}
+
+/******************************************************************************
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ * hardware. Many pins need to be moved from protect to primary
+ * mode.
+ *****************************************************************************/
+void set_muxconf_regs(void)
+{
+ MUX_PANDORA();
+}
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Grazvydas Ignotas <notasas@gmail.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _PANDORA_H_
+#define _PANDORA_H_
+
+const omap3_sysinfo sysinfo = {
+ SDP_3430_V1,
+ SDP_3430_V2,
+ DDR_STACKED,
+ "3530",
+ "OMAP3 Pandora",
+ "NAND",
+};
+
+/*
+ * IEN - Input Enable
+ * IDIS - Input Disable
+ * PTD - Pull type Down
+ * PTU - Pull type Up
+ * DIS - Pull type selection is inactive
+ * EN - Pull type selection is active
+ * M0 - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_PANDORA() \
+ /*SDRC*/\
+ MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) /*SDRC_D0*/\
+ MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /*SDRC_D1*/\
+ MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /*SDRC_D2*/\
+ MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /*SDRC_D3*/\
+ MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /*SDRC_D4*/\
+ MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /*SDRC_D5*/\
+ MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /*SDRC_D6*/\
+ MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /*SDRC_D7*/\
+ MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /*SDRC_D8*/\
+ MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /*SDRC_D9*/\
+ MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /*SDRC_D10*/\
+ MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /*SDRC_D11*/\
+ MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /*SDRC_D12*/\
+ MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /*SDRC_D13*/\
+ MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /*SDRC_D14*/\
+ MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /*SDRC_D15*/\
+ MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /*SDRC_D16*/\
+ MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /*SDRC_D17*/\
+ MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /*SDRC_D18*/\
+ MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /*SDRC_D19*/\
+ MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /*SDRC_D20*/\
+ MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /*SDRC_D21*/\
+ MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /*SDRC_D22*/\
+ MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /*SDRC_D23*/\
+ MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /*SDRC_D24*/\
+ MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /*SDRC_D25*/\
+ MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /*SDRC_D26*/\
+ MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /*SDRC_D27*/\
+ MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /*SDRC_D28*/\
+ MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /*SDRC_D29*/\
+ MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /*SDRC_D30*/\
+ MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /*SDRC_D31*/\
+ MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /*SDRC_CLK*/\
+ MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /*SDRC_DQS0*/\
+ MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /*SDRC_DQS1*/\
+ MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /*SDRC_DQS2*/\
+ MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /*SDRC_DQS3*/\
+ /*GPMC*/\
+ MUX_VAL(CP(GPMC_A1), (IDIS | PTD | DIS | M0)) /*GPMC_A1*/\
+ MUX_VAL(CP(GPMC_A2), (IDIS | PTD | DIS | M0)) /*GPMC_A2*/\
+ MUX_VAL(CP(GPMC_A3), (IDIS | PTD | DIS | M0)) /*GPMC_A3*/\
+ MUX_VAL(CP(GPMC_A4), (IDIS | PTD | DIS | M0)) /*GPMC_A4*/\
+ MUX_VAL(CP(GPMC_A5), (IDIS | PTD | DIS | M0)) /*GPMC_A5*/\
+ MUX_VAL(CP(GPMC_A6), (IDIS | PTD | DIS | M0)) /*GPMC_A6*/\
+ MUX_VAL(CP(GPMC_A7), (IDIS | PTD | DIS | M0)) /*GPMC_A7*/\
+ MUX_VAL(CP(GPMC_A8), (IDIS | PTD | DIS | M0)) /*GPMC_A8*/\
+ MUX_VAL(CP(GPMC_A9), (IDIS | PTD | DIS | M0)) /*GPMC_A9*/\
+ MUX_VAL(CP(GPMC_A10), (IDIS | PTD | DIS | M0)) /*GPMC_A10*/\
+ MUX_VAL(CP(GPMC_D0), (IEN | PTD | DIS | M0)) /*GPMC_D0*/\
+ MUX_VAL(CP(GPMC_D1), (IEN | PTD | DIS | M0)) /*GPMC_D1*/\
+ MUX_VAL(CP(GPMC_D2), (IEN | PTD | DIS | M0)) /*GPMC_D2*/\
+ MUX_VAL(CP(GPMC_D3), (IEN | PTD | DIS | M0)) /*GPMC_D3*/\
+ MUX_VAL(CP(GPMC_D4), (IEN | PTD | DIS | M0)) /*GPMC_D4*/\
+ MUX_VAL(CP(GPMC_D5), (IEN | PTD | DIS | M0)) /*GPMC_D5*/\
+ MUX_VAL(CP(GPMC_D6), (IEN | PTD | DIS | M0)) /*GPMC_D6*/\
+ MUX_VAL(CP(GPMC_D7), (IEN | PTD | DIS | M0)) /*GPMC_D7*/\
+ MUX_VAL(CP(GPMC_D8), (IEN | PTD | DIS | M0)) /*GPMC_D8*/\
+ MUX_VAL(CP(GPMC_D9), (IEN | PTD | DIS | M0)) /*GPMC_D9*/\
+ MUX_VAL(CP(GPMC_D10), (IEN | PTD | DIS | M0)) /*GPMC_D10*/\
+ MUX_VAL(CP(GPMC_D11), (IEN | PTD | DIS | M0)) /*GPMC_D11*/\
+ MUX_VAL(CP(GPMC_D12), (IEN | PTD | DIS | M0)) /*GPMC_D12*/\
+ MUX_VAL(CP(GPMC_D13), (IEN | PTD | DIS | M0)) /*GPMC_D13*/\
+ MUX_VAL(CP(GPMC_D14), (IEN | PTD | DIS | M0)) /*GPMC_D14*/\
+ MUX_VAL(CP(GPMC_D15), (IEN | PTD | DIS | M0)) /*GPMC_D15*/\
+ MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /*GPMC_nCS0*/\
+ MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M0)) /*GPMC_nCS1*/\
+ MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M0)) /*GPMC_nCS2*/\
+ MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M0)) /*GPMC_nCS3*/\
+ MUX_VAL(CP(GPMC_NCS4), (IDIS | PTU | EN | M0))\
+ MUX_VAL(CP(GPMC_NCS5), (IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M1))\
+ MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M1))\
+ MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M0))\
+ MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0))\
+ MUX_VAL(CP(GPMC_CLK), (IDIS | PTD | DIS | M0)) /*GPMC_CLK*/\
+ MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /*GPMC_nADV_ALE*/\
+ MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\
+ MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\
+ MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTD | DIS | M0)) /*GPMC_nBE0_CLE*/\
+ MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0)) /*GPMC_nWP*/\
+ MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) /*GPMC_WAIT0*/\
+ MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) /*GPMC_WAIT1*/\
+ /*DSS*/\
+ MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
+ MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0)) /*DSS_HSYNC*/\
+ MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0)) /*DSS_VSYNC*/\
+ MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0)) /*DSS_ACBIAS*/\
+ MUX_VAL(CP(DSS_DATA0), (IDIS | PTD | DIS | M0)) /*DSS_DATA0*/\
+ MUX_VAL(CP(DSS_DATA1), (IDIS | PTD | DIS | M0)) /*DSS_DATA1*/\
+ MUX_VAL(CP(DSS_DATA2), (IDIS | PTD | DIS | M0)) /*DSS_DATA2*/\
+ MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M0)) /*DSS_DATA3*/\
+ MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M0)) /*DSS_DATA4*/\
+ MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M0)) /*DSS_DATA5*/\
+ MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0)) /*DSS_DATA6*/\
+ MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0)) /*DSS_DATA7*/\
+ MUX_VAL(CP(DSS_DATA8), (IDIS | PTD | DIS | M0)) /*DSS_DATA8*/\
+ MUX_VAL(CP(DSS_DATA9), (IDIS | PTD | DIS | M0)) /*DSS_DATA9*/\
+ MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0)) /*DSS_DATA10*/\
+ MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0)) /*DSS_DATA11*/\
+ MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0)) /*DSS_DATA12*/\
+ MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0)) /*DSS_DATA13*/\
+ MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0)) /*DSS_DATA14*/\
+ MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0)) /*DSS_DATA15*/\
+ MUX_VAL(CP(DSS_DATA16), (IDIS | PTD | DIS | M0)) /*DSS_DATA16*/\
+ MUX_VAL(CP(DSS_DATA17), (IDIS | PTD | DIS | M0)) /*DSS_DATA17*/\
+ MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M0)) /*DSS_DATA18*/\
+ MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0)) /*DSS_DATA19*/\
+ MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0)) /*DSS_DATA20*/\
+ MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0)) /*DSS_DATA21*/\
+ MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0)) /*DSS_DATA22*/\
+ MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0)) /*DSS_DATA23*/\
+ /*GPIO based game buttons*/\
+ MUX_VAL(CP(CAM_XCLKA), (IEN | PTU | DIS | M4)) /*GPIO_96 - LEFT*/\
+ MUX_VAL(CP(CAM_PCLK), (IEN | PTU | DIS | M4)) /*GPIO_97 - L2*/\
+ MUX_VAL(CP(CAM_FLD), (IEN | PTU | DIS | M4)) /*GPIO_98 - RIGHT*/\
+ MUX_VAL(CP(CAM_D0), (IEN | PTU | DIS | M4)) /*GPIO_99 - MENU*/\
+ MUX_VAL(CP(CAM_D1), (IEN | PTU | DIS | M4)) /*GPIO_100 - START*/\
+ MUX_VAL(CP(CAM_D2), (IEN | PTU | DIS | M4)) /*GPIO_101 - Y*/\
+ MUX_VAL(CP(CAM_D3), (IEN | PTU | DIS | M4)) /*GPIO_102 - L1*/\
+ MUX_VAL(CP(CAM_D4), (IEN | PTU | DIS | M4)) /*GPIO_103 - DOWN*/\
+ MUX_VAL(CP(CAM_D5), (IEN | PTU | DIS | M4)) /*GPIO_104 - SELECT*/\
+ MUX_VAL(CP(CAM_D6), (IEN | PTU | DIS | M4)) /*GPIO_105 - R1*/\
+ MUX_VAL(CP(CAM_D7), (IEN | PTU | DIS | M4)) /*GPIO_106 - B*/\
+ MUX_VAL(CP(CAM_D8), (IEN | PTU | DIS | M4)) /*GPIO_107 - R2*/\
+ MUX_VAL(CP(CAM_D10), (IEN | PTU | DIS | M4)) /*GPIO_109 - X*/\
+ MUX_VAL(CP(CAM_D11), (IEN | PTU | DIS | M4)) /*GPIO_110 - UP*/\
+ MUX_VAL(CP(CAM_XCLKB), (IEN | PTU | DIS | M4)) /*GPIO_111 - A*/\
+ /*Audio Interface To External DAC (Headphone, Speakers)*/\
+ MUX_VAL(CP(MCBSP2_FSX), (IDIS | PTD | DIS | M0)) /*McBSP2_FSX*/\
+ MUX_VAL(CP(MCBSP2_CLKX), (IDIS | PTD | DIS | M0)) /*McBSP2_CLKX*/\
+ MUX_VAL(CP(MCBSP2_DX), (IDIS | PTD | DIS | M0)) /*McBSP2_DX*/\
+ MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) /*McBSP_CLKS*/\
+ MUX_VAL(CP(MCBSP2_DR), (IDIS | PTD | DIS | M4)) /*GPIO_118*/\
+ /* - nPOWERDOWN_DAC*/\
+ /*Expansion card 1*/\
+ MUX_VAL(CP(MMC1_CLK), (IDIS | PTU | EN | M0)) /*MMC1_CLK*/\
+ MUX_VAL(CP(MMC1_CMD), (IEN | PTU | EN | M0)) /*MMC1_CMD*/\
+ MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | EN | M0)) /*MMC1_DAT0*/\
+ MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | EN | M0)) /*MMC1_DAT1*/\
+ MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | EN | M0)) /*MMC1_DAT2*/\
+ MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | EN | M0)) /*MMC1_DAT3*/\
+ MUX_VAL(CP(MMC1_DAT4), (IEN | PTD | DIS | M4)) /*GPIO_126 - MMC1_WP*/\
+ /*Expansion card 2*/\
+ MUX_VAL(CP(MMC2_CLK), (IDIS | PTD | DIS | M0)) /*MMC2_CLK*/\
+ MUX_VAL(CP(MMC2_CMD), (IEN | PTU | EN | M0)) /*MMC2_CMD*/\
+ MUX_VAL(CP(MMC2_DAT0), (IEN | PTU | EN | M0)) /*MMC2_DAT0*/\
+ MUX_VAL(CP(MMC2_DAT1), (IEN | PTU | EN | M0)) /*MMC2_DAT1*/\
+ MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | EN | M0)) /*MMC2_DAT2*/\
+ MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M0)) /*MMC2_DAT3*/\
+ MUX_VAL(CP(MMC2_DAT4), (IDIS | PTD | DIS | M1)) /*MMC2_DIR_DAT0*/\
+ MUX_VAL(CP(MMC2_DAT5), (IDIS | PTD | DIS | M1)) /*MMC2_DIR_DAT1*/\
+ MUX_VAL(CP(MMC2_DAT6), (IDIS | PTD | DIS | M1)) /*MMC2_DIR_CMD */\
+ MUX_VAL(CP(MMC2_DAT7), (IEN | PTU | EN | M1)) /*MMC2_CLKIN*/\
+ MUX_VAL(CP(MMC1_DAT5), (IEN | PTD | DIS | M4)) /*GPIO_127 - MMC2_WP*/\
+ /*SDIO Interface to WIFI Module*/\
+ MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | EN | M2)) /*MMC3_CLK*/\
+ MUX_VAL(CP(ETK_CTL_ES2), (IEN | PTD | DIS | M2)) /*MMC3_CMD*/\
+ MUX_VAL(CP(ETK_D4_ES2), (IEN | PTD | DIS | M2)) /*MMC3_DAT0*/\
+ MUX_VAL(CP(ETK_D5_ES2), (IEN | PTD | DIS | M2)) /*MMC3_DAT1*/\
+ MUX_VAL(CP(ETK_D6_ES2), (IEN | PTD | DIS | M2)) /*MMC3_DAT2*/\
+ MUX_VAL(CP(ETK_D3_ES2), (IEN | PTD | DIS | M2)) /*MMC3_DAT3*/\
+ /*Audio Interface To Bluetooth chip*/\
+ MUX_VAL(CP(MCBSP3_DX), (IDIS | PTD | DIS | M0)) /*McBSP3_DX*/\
+ MUX_VAL(CP(MCBSP3_DR), (IEN | PTD | DIS | M0)) /*McBSP3_DR*/\
+ MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTD | DIS | M0)) /*McBSP3_CLKX*/\
+ MUX_VAL(CP(MCBSP3_FSX), (IEN | PTD | DIS | M0)) /*McBSP3_FSX*/\
+ /*Digital Interface to Bluetooth (UART)*/\
+ MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) /*UART1_TX*/\
+ MUX_VAL(CP(UART1_RTS), (IDIS | PTD | DIS | M0)) /*UART1_RTS*/\
+ MUX_VAL(CP(UART1_CTS), (IEN | PTU | EN | M0)) /*UART1_CTS*/\
+ MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0)) /*UART1_RX*/\
+ /*Audio Interface to Triton2 chip (TPS65950)*/\
+ MUX_VAL(CP(MCBSP4_CLKX), (IEN | PTD | DIS | M0)) /*McBSP4_CLKX*/\
+ MUX_VAL(CP(MCBSP4_DR), (IEN | PTD | DIS | M0)) /*McBSP4_DR*/\
+ MUX_VAL(CP(MCBSP4_DX), (IDIS | PTD | DIS | M0)) /*McBSP4_DX*/\
+ MUX_VAL(CP(MCBSP4_FSX), (IEN | PTD | DIS | M0)) /*McBSP4_FSX*/\
+ /*GPIO definitions for muxed pins on AV connector*/\
+ MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M4)) /*GPIO_144,*/\
+ /*UART2_CTS*/\
+ MUX_VAL(CP(UART2_RTS), (IEN | PTU | DIS | M4)) /*GPIO_145,*/\
+ /*UART2_RTS*/\
+ MUX_VAL(CP(UART2_TX), (IEN | PTU | EN | M4)) /*GPIO_146,*/\
+ /*UART2_TX*/\
+ MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M4)) /*GPIO_147,*/\
+ /*UART2_RX*/\
+ /*Serial Interface (Peripheral boot, Linux console, on AV connector)*/\
+ MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0)) /*UART3_RX*/\
+ MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0)) /*UART3_TX*/\
+ /*LEDs (Controlled by OMAP)*/\
+ MUX_VAL(CP(MMC1_DAT6), (IDIS | PTD | DIS | M4)) /*GPIO_128*/\
+ /* - LED_MMC1*/\
+ MUX_VAL(CP(MMC1_DAT7), (IDIS | PTD | DIS | M4)) /*GPIO_129*/\
+ /* - LED_MMC2*/\
+ MUX_VAL(CP(MCBSP1_DX), (IDIS | PTD | DIS | M4)) /*GPIO_158*/\
+ /* - LED_BT*/\
+ MUX_VAL(CP(MCBSP1_DR), (IDIS | PTD | DIS | M4)) /*GPIO_159*/\
+ /* - LED_WIFI*/\
+ /*Switches*/\
+ MUX_VAL(CP(MCSPI1_CS2), (IEN | PTU | DIS | M4)) /*GPIO_176*/\
+ /* - nHOLD_SWITCH*/\
+ MUX_VAL(CP(CAM_D9), (IEN | PTU | DIS | M4)) /*GPIO_108*/\
+ /* - nLID_SWITCH*/\
+ /*External IRQs*/\
+ MUX_VAL(CP(CAM_HS), (IEN | PTU | DIS | M4)) /*GPIO_94*/\
+ /* - nTOUCH_IRQ*/\
+ MUX_VAL(CP(ETK_D7_ES2), (IEN | PTD | DIS | M4)) /*GPIO_21*/\
+ /* - WIFI_IRQ*/\
+ MUX_VAL(CP(MCBSP1_FSX), (IEN | PTD | DIS | M4)) /*GPIO_161*/\
+ /* - nIRQ_NUB1*/\
+ MUX_VAL(CP(CAM_WEN), (IEN | PTU | DIS | M4)) /*GPIO_167*/\
+ /* - nIRQ_NUB2*/\
+ /*Various other stuff*/\
+ MUX_VAL(CP(CAM_VS), (IEN | PTU | DIS | M4)) /*GPIO_95*/\
+ /* - nTOUCH_BUSY*/\
+ MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTD | DIS | M4)) /*GPIO_163*/\
+ /* - nOC_USB5*/\
+ MUX_VAL(CP(MCBSP1_CLKX), (IDIS | PTD | DIS | M4)) /*GPIO_162*/\
+ /* - START_ADC*/\
+ MUX_VAL(CP(ETK_D8_ES2), (IEN | PTD | DIS | M4)) /*GPIO_22*/\
+ /* - MSECURE*/\
+ MUX_VAL(CP(CAM_STROBE), (IEN | PTU | DIS | M4)) /*GPIO_126*/\
+ /* - HP_DETECT*/\
+ /*External Resets and Enables*/\
+ MUX_VAL(CP(ETK_D0_ES2), (IDIS | PTD | DIS | M4)) /*GPIO_14*/\
+ /* - nHDPHN_SHUTDOWN*/\
+ MUX_VAL(CP(ETK_D1_ES2), (IDIS | PTD | DIS | M4)) /*GPIO_15*/\
+ /* - nBT_SHUTDOWN*/\
+ MUX_VAL(CP(ETK_D9_ES2), (IDIS | PTD | DIS | M4)) /*GPIO_23*/\
+ /* - nWIFI_RESET*/\
+ MUX_VAL(CP(MCBSP1_FSR), (IDIS | PTU | DIS | M4)) /*GPIO_157*/\
+ /* - nLCD_RESET*/\
+ MUX_VAL(CP(MCBSP1_CLKR), (IDIS | PTD | DIS | M4)) /*GPIO_156*/\
+ /* - RESET_NUBS*/\
+ MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTU | EN | M4)) /*GPIO_164*/\
+ /* - EN_USB_5V*/\
+ /*Unused*/\
+ MUX_VAL(CP(HDQ_SIO), (IEN | PTU | EN | M0)) /*HDQ_SIO - NC*/\
+ MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0)) /*CSI2_DX0 - NC*/\
+ MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0)) /*CSI2_DY0 - NC*/\
+ MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0)) /*CSI2_DX1 - NC*/\
+ MUX_VAL(CP(CSI2_DY1), (IEN | PTD | DIS | M0)) /*CSI2_DY1 - NC*/\
+ MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M0)) /*I2C2_SCL - NC*/\
+ MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M0)) /*I2C2_SDA - NC*/\
+ /*HS USB OTG Port (connects to HSUSB0)*/\
+ MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0)) /*HSUSB0_CLK*/\
+ MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0)) /*HSUSB0_STP*/\
+ MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0)) /*HSUSB0_DIR*/\
+ MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0)) /*HSUSB0_NXT*/\
+ MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA0*/\
+ MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA1*/\
+ MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA2*/\
+ MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA3*/\
+ MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA4*/\
+ MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA5*/\
+ MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA6*/\
+ MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA7*/\
+ /*I2C Ports*/\
+ MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) /*I2C1_SCL - T2_CTRL*/\
+ MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) /*I2C1_SDA - T2_CTRL*/\
+ MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0)) /*I2C3_SCL - NUBS*/\
+ MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0)) /*I2C3_SDA - NUBS*/\
+ MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0)) /*I2C4_SCL - T2_SR*/\
+ MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0)) /*I2C4_SDA - T2_SR*/\
+ /*Serial Interface (Touch, LCD control)*/\
+ MUX_VAL(CP(MCSPI1_CLK), (IEN | PTD | DIS | M0)) /*McSPI1_CLK*/\
+ MUX_VAL(CP(MCSPI1_SIMO), (IEN | PTD | DIS | M0)) /*McSPI1_SIMO*/\
+ MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M0)) /*McSPI1_SOMI*/\
+ MUX_VAL(CP(MCSPI1_CS0), (IDIS | PTU | EN | M0)) /*McSPI1_CS0 - TOUCH*/\
+ MUX_VAL(CP(MCSPI1_CS1), (IDIS | PTU | EN | M0)) /*McSPI1_CS1 - LCD*/\
+ /*HS USB HOST Port (connects to HSUSB2)*/\
+ MUX_VAL(CP(ETK_D10_ES2), (IDIS | PTD | DIS | M3)) /*USB_HOST_CLK*/\
+ MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTU | EN | M3)) /*USB_HOST_STP*/\
+ MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M3)) /*USB_HOST_DIR*/\
+ MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M3)) /*USB_HOST_NXT*/\
+ MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M3)) /*USB_HOST_D0*/\
+ MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | DIS | M3)) /*USB_HOST_D1*/\
+ MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | DIS | M3)) /*USB_HOST_D2*/\
+ MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | DIS | M3)) /*USB_HOST_D3*/\
+ MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | DIS | M3)) /*USB_HOST_D4*/\
+ MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | DIS | M3)) /*USB_HOST_D5*/\
+ MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | DIS | M3)) /*USB_HOST_D6*/\
+ MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | DIS | M3)) /*USB_HOST_D7*/\
+ MUX_VAL(CP(ETK_D2_ES2), (IDIS | PTD | DIS | M4)) /*GPIO_16*/\
+ /* - nRESET_USB_HOST*/\
+ /*Control and debug */\
+ MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)) /*SYS_32K*/\
+ MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) /*SYS_CLKREQ*/\
+ MUX_VAL(CP(SYS_NIRQ), (IEN | PTU | EN | M0)) /*SYS_nIRQ*/\
+ MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) /*GPIO_2*/\
+ MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) /*GPIO_3*/\
+ MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /*GPIO_4*/\
+ MUX_VAL(CP(SYS_BOOT3), (IEN | PTD | DIS | M4)) /*GPIO_5*/\
+ MUX_VAL(CP(SYS_BOOT4), (IEN | PTD | DIS | M4)) /*GPIO_6*/\
+ MUX_VAL(CP(SYS_BOOT5), (IEN | PTD | DIS | M4)) /*GPIO_7*/\
+ MUX_VAL(CP(SYS_BOOT6), (IEN | PTD | DIS | M4)) /*GPIO_8*/\
+ MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)) /*SYS_OFF_MODE*/\
+ MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M4)) /*SYS_CLKOUT1 - NC*/\
+ MUX_VAL(CP(SYS_CLKOUT2), (IEN | PTD | DIS | M4)) /*SYS_CLKOUT2 - NC*/\
+ /*JTAG*/\
+ MUX_VAL(CP(JTAG_nTRST), (IEN | PTD | DIS | M0)) /*JTAG_nTRST*/\
+ MUX_VAL(CP(JTAG_TCK), (IEN | PTD | DIS | M0)) /*JTAG_TCK*/\
+ MUX_VAL(CP(JTAG_TMS), (IEN | PTD | DIS | M0)) /*JTAG_TMS*/\
+ MUX_VAL(CP(JTAG_TDI), (IEN | PTD | DIS | M0)) /*JTAG_TDI*/\
+ MUX_VAL(CP(JTAG_EMU0), (IEN | PTD | DIS | M0)) /*JTAG_EMU0*/\
+ MUX_VAL(CP(JTAG_EMU1), (IEN | PTD | DIS | M0)) /*JTAG_EMU1*/\
+ /*Die to Die stuff*/\
+ MUX_VAL(CP(D2D_MCAD1), (IEN | PTD | EN | M0)) /*d2d_mcad1*/\
+ MUX_VAL(CP(D2D_MCAD2), (IEN | PTD | EN | M0)) /*d2d_mcad2*/\
+ MUX_VAL(CP(D2D_MCAD3), (IEN | PTD | EN | M0)) /*d2d_mcad3*/\
+ MUX_VAL(CP(D2D_MCAD4), (IEN | PTD | EN | M0)) /*d2d_mcad4*/\
+ MUX_VAL(CP(D2D_MCAD5), (IEN | PTD | EN | M0)) /*d2d_mcad5*/\
+ MUX_VAL(CP(D2D_MCAD6), (IEN | PTD | EN | M0)) /*d2d_mcad6*/\
+ MUX_VAL(CP(D2D_MCAD7), (IEN | PTD | EN | M0)) /*d2d_mcad7*/\
+ MUX_VAL(CP(D2D_MCAD8), (IEN | PTD | EN | M0)) /*d2d_mcad8*/\
+ MUX_VAL(CP(D2D_MCAD9), (IEN | PTD | EN | M0)) /*d2d_mcad9*/\
+ MUX_VAL(CP(D2D_MCAD10), (IEN | PTD | EN | M0)) /*d2d_mcad10*/\
+ MUX_VAL(CP(D2D_MCAD11), (IEN | PTD | EN | M0)) /*d2d_mcad11*/\
+ MUX_VAL(CP(D2D_MCAD12), (IEN | PTD | EN | M0)) /*d2d_mcad12*/\
+ MUX_VAL(CP(D2D_MCAD13), (IEN | PTD | EN | M0)) /*d2d_mcad13*/\
+ MUX_VAL(CP(D2D_MCAD14), (IEN | PTD | EN | M0)) /*d2d_mcad14*/\
+ MUX_VAL(CP(D2D_MCAD15), (IEN | PTD | EN | M0)) /*d2d_mcad15*/\
+ MUX_VAL(CP(D2D_MCAD16), (IEN | PTD | EN | M0)) /*d2d_mcad16*/\
+ MUX_VAL(CP(D2D_MCAD17), (IEN | PTD | EN | M0)) /*d2d_mcad17*/\
+ MUX_VAL(CP(D2D_MCAD18), (IEN | PTD | EN | M0)) /*d2d_mcad18*/\
+ MUX_VAL(CP(D2D_MCAD19), (IEN | PTD | EN | M0)) /*d2d_mcad19*/\
+ MUX_VAL(CP(D2D_MCAD20), (IEN | PTD | EN | M0)) /*d2d_mcad20*/\
+ MUX_VAL(CP(D2D_MCAD21), (IEN | PTD | EN | M0)) /*d2d_mcad21*/\
+ MUX_VAL(CP(D2D_MCAD22), (IEN | PTD | EN | M0)) /*d2d_mcad22*/\
+ MUX_VAL(CP(D2D_MCAD23), (IEN | PTD | EN | M0)) /*d2d_mcad23*/\
+ MUX_VAL(CP(D2D_MCAD24), (IEN | PTD | EN | M0)) /*d2d_mcad24*/\
+ MUX_VAL(CP(D2D_MCAD25), (IEN | PTD | EN | M0)) /*d2d_mcad25*/\
+ MUX_VAL(CP(D2D_MCAD26), (IEN | PTD | EN | M0)) /*d2d_mcad26*/\
+ MUX_VAL(CP(D2D_MCAD27), (IEN | PTD | EN | M0)) /*d2d_mcad27*/\
+ MUX_VAL(CP(D2D_MCAD28), (IEN | PTD | EN | M0)) /*d2d_mcad28*/\
+ MUX_VAL(CP(D2D_MCAD29), (IEN | PTD | EN | M0)) /*d2d_mcad29*/\
+ MUX_VAL(CP(D2D_MCAD30), (IEN | PTD | EN | M0)) /*d2d_mcad30*/\
+ MUX_VAL(CP(D2D_MCAD31), (IEN | PTD | EN | M0)) /*d2d_mcad31*/\
+ MUX_VAL(CP(D2D_MCAD32), (IEN | PTD | EN | M0)) /*d2d_mcad32*/\
+ MUX_VAL(CP(D2D_MCAD33), (IEN | PTD | EN | M0)) /*d2d_mcad33*/\
+ MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0)) /*d2d_mcad34*/\
+ MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0)) /*d2d_mcad35*/\
+ MUX_VAL(CP(D2D_MCAD36), (IEN | PTD | EN | M0)) /*d2d_mcad36*/\
+ MUX_VAL(CP(D2D_CLK26MI), (IEN | PTD | DIS | M0)) /*d2d_clk26mi*/\
+ MUX_VAL(CP(D2D_NRESPWRON), (IEN | PTD | EN | M0)) /*d2d_nrespwron*/\
+ MUX_VAL(CP(D2D_NRESWARM), (IEN | PTU | EN | M0)) /*d2d_nreswarm*/\
+ MUX_VAL(CP(D2D_ARM9NIRQ), (IEN | PTD | DIS | M0)) /*d2d_arm9nirq*/\
+ MUX_VAL(CP(D2D_UMA2P6FIQ), (IEN | PTD | DIS | M0)) /*d2d_uma2p6fiq*/\
+ MUX_VAL(CP(D2D_SPINT), (IEN | PTD | EN | M0)) /*d2d_spint*/\
+ MUX_VAL(CP(D2D_FRINT), (IEN | PTD | EN | M0)) /*d2d_frint*/\
+ MUX_VAL(CP(D2D_DMAREQ0), (IEN | PTD | DIS | M0)) /*d2d_dmareq0*/\
+ MUX_VAL(CP(D2D_DMAREQ1), (IEN | PTD | DIS | M0)) /*d2d_dmareq1*/\
+ MUX_VAL(CP(D2D_DMAREQ2), (IEN | PTD | DIS | M0)) /*d2d_dmareq2*/\
+ MUX_VAL(CP(D2D_DMAREQ3), (IEN | PTD | DIS | M0)) /*d2d_dmareq3*/\
+ MUX_VAL(CP(D2D_N3GTRST), (IEN | PTD | DIS | M0)) /*d2d_n3gtrst*/\
+ MUX_VAL(CP(D2D_N3GTDI), (IEN | PTD | DIS | M0)) /*d2d_n3gtdi*/\
+ MUX_VAL(CP(D2D_N3GTDO), (IEN | PTD | DIS | M0)) /*d2d_n3gtdo*/\
+ MUX_VAL(CP(D2D_N3GTMS), (IEN | PTD | DIS | M0)) /*d2d_n3gtms*/\
+ MUX_VAL(CP(D2D_N3GTCK), (IEN | PTD | DIS | M0)) /*d2d_n3gtck*/\
+ MUX_VAL(CP(D2D_N3GRTCK), (IEN | PTD | DIS | M0)) /*d2d_n3grtck*/\
+ MUX_VAL(CP(D2D_MSTDBY), (IEN | PTU | EN | M0)) /*d2d_mstdby*/\
+ MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0)) /*d2d_swakeup*/\
+ MUX_VAL(CP(D2D_IDLEREQ), (IEN | PTD | DIS | M0)) /*d2d_idlereq*/\
+ MUX_VAL(CP(D2D_IDLEACK), (IEN | PTU | EN | M0)) /*d2d_idleack*/\
+ MUX_VAL(CP(D2D_MWRITE), (IEN | PTD | DIS | M0)) /*d2d_mwrite*/\
+ MUX_VAL(CP(D2D_SWRITE), (IEN | PTD | DIS | M0)) /*d2d_swrite*/\
+ MUX_VAL(CP(D2D_MREAD), (IEN | PTD | DIS | M0)) /*d2d_mread*/\
+ MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0)) /*d2d_sread*/\
+ MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_mbusflag*/\
+ MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_sbusflag*/\
+ MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0)) /*sdrc_cke0*/\
+ MUX_VAL(CP(SDRC_CKE1), (IDIS | PTD | DIS | M7)) /*sdrc_cke1*/
+
+#endif
--- /dev/null
+/*
+ * January 2004 - Changed to support H4 device
+ * Copyright (c) 2004 Texas Instruments
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ cpu/arm_cortexa8/start.o (.text)
+ *(.text)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(.rodata) }
+
+ .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) }
+ __exidx_start = .;
+ .ARM.exidx : { *(.ARM.exidx* .gnu.linkonce.armexidx.*) }
+ __exidx_end = .;
+
+ . = ALIGN(4);
+ .data : { *(.data) }
+
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = ALIGN(4);
+ __bss_start = .;
+ .bss : { *(.bss) }
+ _end = .;
+}
--- /dev/null
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := zoom1.o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+#
+# (C) Copyright 2006-2008
+# Texas Instruments, <www.ti.com>
+#
+# Zoom MDK uses OMAP3 (ARM-CortexA8) cpu
+# see http://www.ti.com/ for more information on Texas Instruments
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# Physical Address:
+# 8000'0000 (bank0)
+# A000/0000 (bank1)
+# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+
+# For use with external or internal boots.
+TEXT_BASE = 0x80e80000
--- /dev/null
+/*
+ * January 2004 - Changed to support H4 device
+ * Copyright (c) 2004-2008 Texas Instruments
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ cpu/arm_cortexa8/start.o (.text)
+ *(.text)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(.rodata) }
+
+ .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) }
+ __exidx_start = .;
+ .ARM.exidx : { *(.ARM.exidx* .gnu.linkonce.armexidx.*) }
+ __exidx_end = .;
+
+ . = ALIGN(4);
+ .data : { *(.data) }
+
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = ALIGN(4);
+ __bss_start = .;
+ .bss : { *(.bss) }
+ _end = .;
+}
--- /dev/null
+/*
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ * Nishanth Menon <nm@ti.com>
+ *
+ * Derived from Beagle Board and 3430 SDP code by
+ * Sunil Kumar <sunilsaini05@gmail.com>
+ * Shashi Ranjan <shashiranjanmca05@gmail.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-types.h>
+#include "zoom1.h"
+
+/******************************************************************************
+ * Routine: board_init
+ * Description: Early hardware init.
+ *****************************************************************************/
+int board_init(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+ /* board id for Linux */
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP_LDP;
+ /* boot param addr */
+ gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+ return 0;
+}
+
+/******************************************************************************
+ * Routine: misc_init_r
+ * Description: Configure zoom board specific configurations
+ *****************************************************************************/
+int misc_init_r(void)
+{
+ power_init_r();
+ return 0;
+}
+
+/******************************************************************************
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ * hardware. Many pins need to be moved from protect to primary
+ * mode.
+ *****************************************************************************/
+void set_muxconf_regs(void)
+{
+ /* platform specific muxes */
+ MUX_ZOOM1_MDK();
+}
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Texas Instruments
+ * Nishanth Menon <nm@ti.com>
+ *
+ * Derived from: board/omap3/beagle/beagle.h
+ * Dirk Behme <dirk.behme@gmail.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _BOARD_ZOOM1_H_
+#define _BOARD_ZOOM1_H_
+
+const omap3_sysinfo sysinfo = {
+ SDP_3430_V1,
+ SDP_3430_V2,
+ DDR_STACKED,
+ "3430",
+ "OMAP3 Zoom MDK Rev 1",
+ "NAND",
+};
+
+/*
+ * IEN - Input Enable
+ * IDIS - Input Disable
+ * PTD - Pull type Down
+ * PTU - Pull type Up
+ * DIS - Pull type selection is inactive
+ * EN - Pull type selection is active
+ * M0 - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_ZOOM1_MDK() \
+ /*SDRC*/\
+ MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) /*SDRC_D0*/\
+ MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /*SDRC_D1*/\
+ MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /*SDRC_D2*/\
+ MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /*SDRC_D3*/\
+ MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /*SDRC_D4*/\
+ MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /*SDRC_D5*/\
+ MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /*SDRC_D6*/\
+ MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /*SDRC_D7*/\
+ MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /*SDRC_D8*/\
+ MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /*SDRC_D9*/\
+ MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /*SDRC_D10*/\
+ MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /*SDRC_D11*/\
+ MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /*SDRC_D12*/\
+ MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /*SDRC_D13*/\
+ MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /*SDRC_D14*/\
+ MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /*SDRC_D15*/\
+ MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /*SDRC_D16*/\
+ MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /*SDRC_D17*/\
+ MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /*SDRC_D18*/\
+ MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /*SDRC_D19*/\
+ MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /*SDRC_D20*/\
+ MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /*SDRC_D21*/\
+ MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /*SDRC_D22*/\
+ MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /*SDRC_D23*/\
+ MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /*SDRC_D24*/\
+ MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /*SDRC_D25*/\
+ MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /*SDRC_D26*/\
+ MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /*SDRC_D27*/\
+ MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /*SDRC_D28*/\
+ MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /*SDRC_D29*/\
+ MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /*SDRC_D30*/\
+ MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /*SDRC_D31*/\
+ MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /*SDRC_CLK*/\
+ MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /*SDRC_DQS0*/\
+ MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /*SDRC_DQS1*/\
+ MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /*SDRC_DQS2*/\
+ MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /*SDRC_DQS3*/\
+ /*GPMC*/\
+ MUX_VAL(CP(GPMC_A1), (IDIS | PTD | DIS | M0)) /*GPMC_A1*/\
+ MUX_VAL(CP(GPMC_A2), (IDIS | PTD | DIS | M0)) /*GPMC_A2*/\
+ MUX_VAL(CP(GPMC_A3), (IDIS | PTD | DIS | M0)) /*GPMC_A3*/\
+ MUX_VAL(CP(GPMC_A4), (IDIS | PTD | DIS | M0)) /*GPMC_A4*/\
+ MUX_VAL(CP(GPMC_A5), (IDIS | PTD | DIS | M0)) /*GPMC_A5*/\
+ MUX_VAL(CP(GPMC_A6), (IDIS | PTD | DIS | M0)) /*GPMC_A6*/\
+ MUX_VAL(CP(GPMC_A7), (IDIS | PTD | DIS | M0)) /*GPMC_A7*/\
+ MUX_VAL(CP(GPMC_A8), (IDIS | PTD | DIS | M0)) /*GPMC_A8*/\
+ MUX_VAL(CP(GPMC_A9), (IDIS | PTD | DIS | M0)) /*GPMC_A9*/\
+ MUX_VAL(CP(GPMC_A10), (IDIS | PTD | DIS | M0)) /*GPMC_A10*/\
+ MUX_VAL(CP(GPMC_D0), (IEN | PTD | DIS | M0)) /*GPMC_D0*/\
+ MUX_VAL(CP(GPMC_D1), (IEN | PTD | DIS | M0)) /*GPMC_D1*/\
+ MUX_VAL(CP(GPMC_D2), (IEN | PTD | DIS | M0)) /*GPMC_D2*/\
+ MUX_VAL(CP(GPMC_D3), (IEN | PTD | DIS | M0)) /*GPMC_D3*/\
+ MUX_VAL(CP(GPMC_D4), (IEN | PTD | DIS | M0)) /*GPMC_D4*/\
+ MUX_VAL(CP(GPMC_D5), (IEN | PTD | DIS | M0)) /*GPMC_D5*/\
+ MUX_VAL(CP(GPMC_D6), (IEN | PTD | DIS | M0)) /*GPMC_D6*/\
+ MUX_VAL(CP(GPMC_D7), (IEN | PTD | DIS | M0)) /*GPMC_D7*/\
+ MUX_VAL(CP(GPMC_D8), (IEN | PTD | DIS | M0)) /*GPMC_D8*/\
+ MUX_VAL(CP(GPMC_D9), (IEN | PTD | DIS | M0)) /*GPMC_D9*/\
+ MUX_VAL(CP(GPMC_D10), (IEN | PTD | DIS | M0)) /*GPMC_D10*/\
+ MUX_VAL(CP(GPMC_D11), (IEN | PTD | DIS | M0)) /*GPMC_D11*/\
+ MUX_VAL(CP(GPMC_D12), (IEN | PTD | DIS | M0)) /*GPMC_D12*/\
+ MUX_VAL(CP(GPMC_D13), (IEN | PTD | DIS | M0)) /*GPMC_D13*/\
+ MUX_VAL(CP(GPMC_D14), (IEN | PTD | DIS | M0)) /*GPMC_D14*/\
+ MUX_VAL(CP(GPMC_D15), (IEN | PTD | DIS | M0)) /*GPMC_D15*/\
+ MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /*GPMC_nCS0*/\
+ MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M7)) /*GPMC_nCS1*/\
+ MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M7)) /*GPMC_nCS2*/\
+ MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M7)) /*GPMC_nCS3*/\
+ MUX_VAL(CP(GPMC_NCS4), (IDIS | PTU | EN | M7)) /*GPMC_nCS4*/\
+ MUX_VAL(CP(GPMC_NCS5), (IDIS | PTD | DIS | M7)) /*GPMC_nCS5*/\
+ MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M7)) /*GPMC_nCS6*/\
+ MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M7)) /*GPMC_nCS7*/\
+ MUX_VAL(CP(GPMC_CLK), (IDIS | PTD | DIS | M0)) /*GPMC_CLK*/\
+ MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /*GPMC_nADV_ALE*/\
+ MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\
+ MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\
+ MUX_VAL(CP(GPMC_NWP), (IDIS | PTU | DIS | M0)) /*GPMC_nWP*/\
+ MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTD | DIS | M0)) /*GPMC_nBE0_CLE*/\
+ MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | DIS | M0)) /*GPMC_nBE1*/\
+ MUX_VAL(CP(GPMC_WAIT0), (IEN | PTD | EN | M0)) /*GPMC_WAIT0*/\
+ MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) /*GPMC_WAIT1*/\
+ MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M0)) /*GPMC_WAIT2*/\
+ MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) /*GPMC_WAIT3*/
+
+#endif /* _BOARD_ZOOM_H_ */
--- /dev/null
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# (C) Copyright 2004
+# ARM Ltd.
+# Philippe Robin, <philippe.robin@arm.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := nmdk8815.o
+SOBJS := platform.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+# (C) Copyright 2007
+# STMicroelectronics, <www.st.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+#
+# image should be loaded at 0x01000000
+#
+
+TEXT_BASE = 0x03F80000
--- /dev/null
+/*
+ * (C) Copyright 2005
+ * STMicrolelctronics, <www.st.com>
+ *
+ * (C) Copyright 2004
+ * ARM Ltd.
+ * Philippe Robin, <philippe.robin@arm.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_SHOW_BOOT_PROGRESS
+void show_boot_progress(int progress)
+{
+ printf("%i\n", progress);
+}
+#endif
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+int board_init(void)
+{
+ gd->bd->bi_arch_number = MACH_TYPE_NOMADIK;
+ gd->bd->bi_boot_params = 0x00000100;
+ writel(0xC37800F0, NOMADIK_GPIO1_BASE + 0x20);
+ writel(0x00000000, NOMADIK_GPIO1_BASE + 0x24);
+ writel(0x00000000, NOMADIK_GPIO1_BASE + 0x28);
+ writel(readl(NOMADIK_SRC_BASE) | 0x8000, NOMADIK_SRC_BASE);
+
+ icache_enable();
+
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ setenv("verify", "n");
+ return 0;
+}
+
+int dram_init(void)
+{
+ /* set dram bank start addr and size */
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+ gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+ gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+ return 0;
+}
--- /dev/null
+/*
+ * Board specific setup info
+ *
+ * (C) Copyright 2005
+ * STMicrolelctronics, <www.st.com>
+ *
+ * (C) Copyright 2004, ARM Ltd.
+ * Philippe Robin, <philippe.robin@arm.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+.globl lowlevel_init
+lowlevel_init:
+ /* Jump to the flash address */
+ ldr r0, =CFG_ONENAND_BASE
+
+ /*
+ * Make it independent whether we boot from 0x0 or 0x30000000.
+ * Non-portable: it relies on the knowledge that ip has to be updated
+ */
+ orr ip, ip, r0 /* adjust return address of cpu_init_crit */
+ orr lr, lr, r0 /* adjust return address */
+ orr pc, pc, r0 /* jump to the normal address */
+ nop
+
+ /* Initialize PLL, Remap clear, FSMC, MPMC here! */
+ /* What about GPIO, CLCD and UART */
+
+ /* PLL Initialization */
+ /* Prog the PLL1 @ 266 MHz ==> SDRAM Clock = 100.8 MHz */
+ ldr r0, =NOMADIK_SRC_BASE
+
+ ldr r1, =0x2B013502
+
+ str r1, [r0, #0x14]
+
+ /* Used to set all the timers clock to 2.4MHZ */
+ ldr r1, =0x2AAAA004
+ str r1, [r0]
+
+ ldr r1, =0x10000000
+ str r1, [r0, #0x10]
+
+ /* FSMC setup ---- */
+ ldr r0, =NOMADIK_FSMC_BASE
+
+ ldr r1, =0x10DB /* For 16-bit NOR flash */
+ str r1, [r0, #0x08]
+
+ ldr r1, =0x03333333 /* For 16-bit NOR flash */
+ str r1, [r0, #0xc]
+
+ /* oneNAND setting */
+ ldr r1, =0x0000105B /* BCR0 Prog control register */
+ str r1, [r0]
+
+ ldr r1, =0x0A200551 /* BTR0 Prog timing register */
+ str r1, [r0, #0x04]
+
+ /* preload the instructions into icache */
+ add r0, pc, #0x1F
+ bic r0, r0, #0x1F
+ mcr p15, 0, r0, c7, c13, 1
+ add r0, r0, #0x20
+ mcr p15, 0, r0, c7, c13, 1
+
+ /* Now Clear Remap */
+ ldr r0, =NOMADIK_SRC_BASE
+
+ ldr r1, =0x2004
+ str r1, [r0]
+
+ ldr r1, =0x10000000
+ str r1, [r0, #0x10]
+
+ ldr r0, =0x101E9000
+ ldr r1, =0x2004
+ str r1, [r0]
+
+ ldr r0, =NOMADIK_SRC_BASE
+ ldr r1, =0x2104
+ str r1, [r0]
+
+ /* FSMC setup -- */
+ mov r0, #(NOMADIK_FSMC_BASE & 0x10000000)
+ orr r0, r0, #(NOMADIK_FSMC_BASE & 0x0FFFFFFF)
+
+ ldr r1, =0x10DB /* For 16-bit NOR flash */
+ str r1, [r0, #0x8]
+
+ ldr r1, =0x03333333 /* For 16-bit NOR flash */
+ str r1, [r0, #0xc]
+
+ /* MPMC Setup */
+ ldr r0, =NOMADIK_MPMC_BASE
+
+ ldr r1, =0xF00003
+ str r1, [r0] /* Enable the MPMC and the DLL */
+
+ ldr r1, =0x183
+ str r1, [r0, #0x20]
+
+ ldr r2, =NOMADIK_PMU_BASE
+
+ ldr r1, =0x1111
+ str r1, [r2]
+
+ ldr r1, =0x1111 /* Prog the, mand delay strategy */
+ str r1, [r0, #0x28]
+
+ ldr r1, =0x103 /* NOP ,mand */
+ str r1, [r0, #0x20]
+
+ /* FIXME -- Wait required here */
+
+ ldr r1, =0x103 /* PALL ,mand*/
+ str r1, [r0, #0x20]
+
+ ldr r1, =0x1
+ str r1, [r0, #0x24] /* To do at least two auto-refresh */
+
+ /* FIXME -- Wait required here */
+
+ /* Auto-refresh period = 7.8us @ SDRAM Clock = 100.8 MHz */
+ ldr r1, =0x31
+ str r1, [r0, #0x24]
+
+ /* Prog Little Endian, Not defined in 8800 board */
+ ldr r1, =0x0
+ str r1, [r0, #0x8]
+
+
+ ldr r1, =0x2
+ str r1, [r0, #0x30] /* Prog tRP timing */
+
+ ldr r1, =0x4 /* Change for 8815 */
+ str r1, [r0, #0x34] /* Prog tRAS timing */
+
+ ldr r1, =0xB
+ str r1, [r0, #0x38] /* Prog tSREX timing */
+
+
+ ldr r1, =0x1
+ str r1, [r0, #0x44] /* Prog tWR timing */
+
+ ldr r1, =0x8
+ str r1, [r0, #0x48] /* Prog tRC timing */
+
+ ldr r1, =0xA
+ str r1, [r0, #0x4C] /* Prog tRFC timing */
+
+ ldr r1, =0xB
+ str r1, [r0, #0x50] /* Prog tXSR timing */
+
+ ldr r1, =0x1
+ str r1, [r0, #0x54] /* Prog tRRD timing */
+
+ ldr r1, =0x1
+ str r1, [r0, #0x58] /* Prog tMRD timing */
+
+ ldr r1, =0x1
+ str r1, [r0, #0x5C] /* Prog tCDLR timing */
+
+ /* DDR-SDRAM MEMORY IS ON BANK0 8815 */
+ ldr r1, =0x304 /* Prog RAS and CAS for CS 0 */
+ str r1, [r0, #0x104]
+
+ /* SDR-SDRAM MEMORY IS ON BANK1 8815 */
+ ldr r1, =0x304 /* Prog RAS and CAS for CS 1 */
+ str r1, [r0, #0x124]
+ /* THE DATA BUS WIDE IS PROGRAM FOR 16-BITS */
+ /* DDR-SDRAM MEMORY IS ON BANK0*/
+
+ ldr r1, =0x884 /* 8815 : config reg in BRC for CS0 */
+ str r1, [r0, #0x100]
+
+ /*SDR-SDRAM MEMORY IS ON BANK1*/
+
+ ldr r1, =0x884 /* 8815 : config reg in BRC for CS1 */
+ str r1, [r0, #0x120]
+
+ ldr r1, =0x83 /*MODE Mand*/
+ str r1, [r0, #0x20]
+
+ /* LOAD MODE REGISTER FOR 2 bursts of 16b, with DDR mem ON BANK0 */
+
+ ldr r1, =0x62000 /*Data in*/
+ ldr r1, [r1]
+
+ /* LOAD MODE REGISTER FOR 2 bursts of 16b, with DDR mem ON BANK1 */
+
+ ldr r1, =0x8062000
+ ldr r1, [r1]
+
+ ldr r1, =0x003
+ str r1, [r0, #0x20]
+
+ /* ENABLE ALL THE BUFFER FOR EACH AHB PORT*/
+
+ ldr r1, =0x01 /* Enable buffer 0 */
+ str r1, [r0, #0x400]
+
+ ldr r1, =0x01 /* Enable buffer 1 */
+ str r1, [r0, #0x420]
+
+ ldr r1, =0x01 /* Enable buffer 2 */
+ str r1, [r0, #0x440]
+
+ ldr r1, =0x01 /* Enable buffer 3 */
+ str r1, [r0, #0x460]
+
+ ldr r1, =0x01 /* Enable buffer 4 */
+ str r1, [r0, #0x480]
+
+ ldr r1, =0x01 /* Enable buffer 5 */
+ str r1, [r0, #0x4A0]
+
+ /* GPIO settings */
+
+ ldr r0, =NOMADIK_GPIO1_BASE
+
+ ldr r1, =0xC0600000
+ str r1, [r0, #0x20]
+
+ ldr r1, =0x3F9FFFFF /* ABHI change this for uart1 */
+ str r1, [r0, #0x24]
+
+ ldr r1, =0x3F9FFFFF /* ABHI change this for uart1 */
+ str r1, [r0, #0x28]
+
+ ldr r0, =NOMADIK_GPIO0_BASE
+
+ ldr r1, =0xFFFFFFFF
+ str r1, [r0, #0x20]
+
+ ldr r1, =0x00
+ str r1, [r0, #0x24]
+
+ ldr r1, =0x00
+ str r1, [r0, #0x28]
+
+ /* Configure CPLD_CTRL register for enabling MUX logic for UART0/UART2 */
+
+ ldr r0, =NOMADIK_FSMC_BASE
+
+ ldr r1, =0x10DB /* INIT FSMC bank 0 */
+ str r1, [r0, #0x00]
+
+ ldr r1, =0x0FFFFFFF
+ str r1, [r0, #0x04]
+
+ ldr r1, =0x010DB /* INIT FSMC bank 1 */
+ str r1, [r0, #0x08]
+
+ ldr r1, =0x00FFFFFFF
+ str r1, [r0, #0x0C]
+
+ ldr r0, =NOMADIK_UART0_BASE
+
+ ldr r1, =0x00000000
+ str r1, [r0, #0x30]
+
+ ldr r1, =0x0000004e
+ str r1, [r0, #0x24]
+
+ ldr r1, =0x00000008
+ str r1, [r0, #0x28]
+
+ ldr r1, =0x00000060
+ str r1, [r0, #0x2C]
+
+ ldr r1, =0x00000301
+ str r1, [r0, #0x30]
+
+ ldr r1, =0x00000066
+ str r1, [r0]
+
+ ldr r0, =NOMADIK_UART1_BASE
+
+ ldr r1, =0x00000000
+ str r1, [r0, #0x30]
+
+ ldr r1, =0x0000004e
+ str r1, [r0, #0x24]
+
+ ldr r1, =0x00000008
+ str r1, [r0, #0x28]
+
+ ldr r1, =0x00000060
+ str r1, [r0, #0x2C]
+
+ ldr r1, =0x00000301
+ str r1, [r0, #0x30]
+
+ ldr r1, =0x00000066
+ str r1, [r0]
+
+ ldr r0, =NOMADIK_UART2_BASE
+
+ ldr r1, =0x00000000
+ str r1, [r0, #0x30]
+
+ ldr r1, =0x0000004e
+ str r1, [r0, #0x24]
+
+ ldr r1, =0x00000008
+ str r1, [r0, #0x28]
+
+ ldr r1, =0x00000060
+ str r1, [r0, #0x2C]
+
+ ldr r1, =0x00000301
+ str r1, [r0, #0x30]
+
+ ldr r1, =0x00000066
+ str r1, [r0]
+
+ /* Configure CPLD to enable UART0 */
+
+ mov pc, lr
--- /dev/null
+/*
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+ . = ALIGN(4);
+ .text :
+ {
+ cpu/arm926ejs/start.o (.text)
+ *(.text)
+ }
+ . = ALIGN(4);
+ .rodata : { *(.rodata) }
+ . = ALIGN(4);
+ .data : { *(.data) }
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = ALIGN(4);
+ __bss_start = .;
+ .bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
+ _end = .;
+}
--- /dev/null
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(SOC).a
+
+COBJS = timer.o
+SOBJS = reset.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS)) $(addprefix $(obj),$(SOBJS))
+
+all: $(obj).depend $(LIB)
+
+$(LIB): $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+#include <config.h>
+/*
+ * Processor reset for Nomadik
+ */
+
+ .align 5
+.globl reset_cpu
+reset_cpu:
+#if defined CONFIG_NOMADIK_8815
+ ldr r0, =NOMADIK_SRC_BASE
+ ldr r1, =0x1
+ str r1, [r0, #0x18]
+#else
+ ldr r1, rstctl1 /* get clkm1 reset ctl */
+ mov r3, #0x0
+ strh r3, [r1] /* clear it */
+ mov r3, #0x8
+ strh r3, [r1] /* force dsp+arm reset */
+#endif
+
+_loop_forever:
+ b _loop_forever
+
+rstctl1:
+ .word 0xfffece10
--- /dev/null
+/*
+ * (C) Copyright 2003
+ * Texas Instruments <www.ti.com>
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Alex Zuepke <azu@sysgo.de>
+ *
+ * (C) Copyright 2002-2004
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * (C) Copyright 2004
+ * Philippe Robin, ARM Ltd. <philippe.robin@arm.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <arm926ejs.h>
+
+#define TIMER_LOAD_VAL 0xffffffff
+
+/* macro to read the 32 bit timer */
+#define READ_TIMER readl(CONFIG_SYS_TIMERBASE + 20)
+
+static ulong timestamp;
+static ulong lastdec;
+
+/* nothing really to do with interrupts, just starts up a counter. */
+int timer_init(void)
+{
+ /* Load timer with initial value */
+ writel(TIMER_LOAD_VAL, CONFIG_SYS_TIMERBASE + 16);
+
+ /*
+ * Set timer to be enabled, free-running, no interrupts, 256 divider,
+ * 32-bit, wrap-mode
+ */
+ writel(0x8a, CONFIG_SYS_TIMERBASE + 24);
+
+ /* init the timestamp and lastdec value */
+ reset_timer_masked();
+
+ return 0;
+}
+
+/*
+ * timer without interrupts
+ */
+void reset_timer(void)
+{
+ reset_timer_masked();
+}
+
+ulong get_timer(ulong base)
+{
+ return get_timer_masked() - base;
+}
+
+void set_timer(ulong t)
+{
+ timestamp = t;
+}
+
+/* delay x useconds AND perserve advance timstamp value */
+void udelay(unsigned long usec)
+{
+ ulong tmo, tmp;
+
+ if (usec >= 1000) {
+ /* if "big" number, spread normalization to seconds */
+ tmo = usec / 1000; /* start to normalize */
+ tmo *= CONFIG_SYS_HZ; /* find number of "ticks" */
+ tmo /= 1000; /* finish normalize. */
+ } else {
+ /* small number, don't kill it prior to HZ multiply */
+ tmo = usec * CONFIG_SYS_HZ;
+ tmo /= (1000 * 1000);
+ }
+
+ tmp = get_timer(0); /* get current timestamp */
+ if ((tmo + tmp + 1) < tmp) /* will roll time stamp? */
+ reset_timer_masked(); /* reset to 0, set lastdec value */
+ else
+ tmo += tmp;
+
+ while (get_timer_masked() < tmo)
+ /* nothing */ ;
+}
+
+void reset_timer_masked(void)
+{
+ /* reset time */
+ lastdec = READ_TIMER; /* capure current decrementer value time */
+ timestamp = 0; /* start "advancing" time stamp from 0 */
+}
+
+ulong get_timer_masked(void)
+{
+ ulong now = READ_TIMER; /* current tick value */
+
+ if (lastdec >= now) { /* normal mode (non roll) */
+ /* move stamp fordward */
+ timestamp += lastdec - now;
+ } else {
+ /*
+ * An overflow is expected.
+ * nts = ts + ld + (TLV - now)
+ * ts=old stamp, ld=time that passed before passing through -1
+ * (TLV-now) amount of time after passing though -1
+ * nts = new "advancing time stamp"...it could also roll
+ */
+ timestamp += lastdec + TIMER_LOAD_VAL - now;
+ }
+ lastdec = now;
+
+ return timestamp;
+}
+
+/* waits specified delay value and resets timestamp */
+void udelay_masked(unsigned long usec)
+{
+ ulong tmo;
+
+ if (usec >= 1000) {
+ /* if "big" number, spread normalization to seconds */
+ tmo = usec / 1000; /* start to normalize */
+ tmo *= CONFIG_SYS_HZ; /* find number of "ticks" */
+ tmo /= 1000; /* finish normalize. */
+ } else {
+ /* else small number, don't kill it prior to HZ multiply */
+ tmo = usec * CONFIG_SYS_HZ;
+ tmo /= (1000*1000);
+ }
+
+ reset_timer_masked();
+ /* set "advancing" timestamp to 0, set lastdec vaule */
+
+ while (get_timer_masked() < tmo)
+ /* nothing */ ;
+}
+
+/*
+ * This function is derived from PowerPC code (read timebase as long long).
+ * On ARM it just returns the timer value.
+ */
+unsigned long long get_ticks(void)
+{
+ return get_timer(0);
+}
+
+/*
+ * This function is derived from PowerPC code (timebase clock frequency).
+ * On ARM it returns the number of timer ticks per second.
+ */
+ulong get_tbclk(void)
+{
+ ulong tbclk;
+
+ tbclk = CONFIG_SYS_HZ;
+ return tbclk;
+}
--- /dev/null
+#
+# (C) Copyright 2000-2003
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(CPU).a
+
+START := start.o
+COBJS := cpu.o
+
+SRCS := $(START:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+START := $(addprefix $(obj),$(START))
+
+all: $(obj).depend $(START) $(LIB)
+
+$(LIB): $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
\ No newline at end of file
--- /dev/null
+#
+# (C) Copyright 2002
+# Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+PLATFORM_RELFLAGS += -fno-strict-aliasing -fno-common -ffixed-r8 \
+ -msoft-float
+
+# Make ARMv5 to allow more compilers to work, even though its v7a.
+PLATFORM_CPPFLAGS += -march=armv5
+# =========================================================================
+#
+# Supply options according to compiler version
+#
+# =========================================================================
+PLATFORM_CPPFLAGS +=$(call cc-option)
+PLATFORM_CPPFLAGS +=$(call cc-option,-mno-thumb-interwork,)
+PLATFORM_RELFLAGS +=$(call cc-option,-mshort-load-bytes,\
+ $(call cc-option,-malignment-traps,))
\ No newline at end of file
--- /dev/null
+/*
+ * (C) Copyright 2008 Texas Insturments
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * CPU specific code
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/arch/sys_proto.h>
+
+#ifdef CONFIG_USE_IRQ
+DECLARE_GLOBAL_DATA_PTR;
+#endif
+
+#ifndef CONFIG_L2_OFF
+void l2cache_disable(void);
+#endif
+
+static void cache_flush(void);
+
+/* read co-processor 15, register #1 (control register) */
+static unsigned long read_p15_c1(void)
+{
+ unsigned long value;
+
+ __asm__ __volatile__("mrc p15, 0, %0, c1, c0, 0\
+ @ read control reg\n":"=r"(value)
+ ::"memory");
+ return value;
+}
+
+/* write to co-processor 15, register #1 (control register) */
+static void write_p15_c1(unsigned long value)
+{
+ __asm__ __volatile__("mcr p15, 0, %0, c1, c0, 0\
+ @ write it back\n"::"r"(value)
+ : "memory");
+
+ read_p15_c1();
+}
+
+static void cp_delay(void)
+{
+ /* Many OMAP regs need at least 2 nops */
+ asm("nop");
+ asm("nop");
+}
+
+/* See also ARM Ref. Man. */
+#define C1_MMU (1<<0) /* mmu off/on */
+#define C1_ALIGN (1<<1) /* alignment faults off/on */
+#define C1_DC (1<<2) /* dcache off/on */
+#define C1_WB (1<<3) /* merging write buffer on/off */
+#define C1_BIG_ENDIAN (1<<7) /* big endian off/on */
+#define C1_SYS_PROT (1<<8) /* system protection */
+#define C1_ROM_PROT (1<<9) /* ROM protection */
+#define C1_IC (1<<12) /* icache off/on */
+#define C1_HIGH_VECTORS (1<<13) /* location of vectors: low/high addresses */
+#define RESERVED_1 (0xf << 3) /* must be 111b for R/W */
+
+int cpu_init(void)
+{
+ /*
+ * setup up stacks if necessary
+ */
+#ifdef CONFIG_USE_IRQ
+ IRQ_STACK_START =
+ _armboot_start - CONFIG_SYS_MALLOC_LEN - CONFIG_SYS_GBL_DATA_SIZE - 4;
+ FIQ_STACK_START = IRQ_STACK_START - CONFIG_STACKSIZE_IRQ;
+#endif
+ return 0;
+}
+
+int cleanup_before_linux(void)
+{
+ unsigned int i;
+
+ /*
+ * this function is called just before we call linux
+ * it prepares the processor for linux
+ *
+ * we turn off caches etc ...
+ */
+ disable_interrupts();
+
+ /* turn off I/D-cache */
+ icache_disable();
+ dcache_disable();
+
+ /* invalidate I-cache */
+ cache_flush();
+
+#ifndef CONFIG_L2_OFF
+ /* turn off L2 cache */
+ l2cache_disable();
+ /* invalidate L2 cache also */
+ v7_flush_dcache_all(get_device_type());
+#endif
+ i = 0;
+ /* mem barrier to sync up things */
+ asm("mcr p15, 0, %0, c7, c10, 4": :"r"(i));
+
+#ifndef CONFIG_L2_OFF
+ l2cache_enable();
+#endif
+
+ return 0;
+}
+
+int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ disable_interrupts();
+ reset_cpu(0);
+
+ /* NOTREACHED */
+ return 0;
+}
+
+void icache_enable(void)
+{
+ ulong reg;
+
+ reg = read_p15_c1(); /* get control reg. */
+ cp_delay();
+ write_p15_c1(reg | C1_IC);
+}
+
+void icache_disable(void)
+{
+ ulong reg;
+
+ reg = read_p15_c1();
+ cp_delay();
+ write_p15_c1(reg & ~C1_IC);
+}
+
+void dcache_disable (void)
+{
+ ulong reg;
+
+ reg = read_p15_c1 ();
+ cp_delay ();
+ write_p15_c1 (reg & ~C1_DC);
+}
+
+void l2cache_enable()
+{
+ unsigned long i;
+ volatile unsigned int j;
+
+ /* ES2 onwards we can disable/enable L2 ourselves */
+ if (get_cpu_rev() == CPU_3430_ES2) {
+ __asm__ __volatile__("mrc p15, 0, %0, c1, c0, 1":"=r"(i));
+ __asm__ __volatile__("orr %0, %0, #0x2":"=r"(i));
+ __asm__ __volatile__("mcr p15, 0, %0, c1, c0, 1":"=r"(i));
+ } else {
+ /* Save r0, r12 and restore them after usage */
+ __asm__ __volatile__("mov %0, r12":"=r"(j));
+ __asm__ __volatile__("mov %0, r0":"=r"(i));
+
+ /*
+ * GP Device ROM code API usage here
+ * r12 = AUXCR Write function and r0 value
+ */
+ __asm__ __volatile__("mov r12, #0x3");
+ __asm__ __volatile__("mrc p15, 0, r0, c1, c0, 1");
+ __asm__ __volatile__("orr r0, r0, #0x2");
+ /* SMI instruction to call ROM Code API */
+ __asm__ __volatile__(".word 0xE1600070");
+ __asm__ __volatile__("mov r0, %0":"=r"(i));
+ __asm__ __volatile__("mov r12, %0":"=r"(j));
+ }
+
+}
+
+void l2cache_disable()
+{
+ unsigned long i;
+ volatile unsigned int j;
+
+ /* ES2 onwards we can disable/enable L2 ourselves */
+ if (get_cpu_rev() == CPU_3430_ES2) {
+ __asm__ __volatile__("mrc p15, 0, %0, c1, c0, 1":"=r"(i));
+ __asm__ __volatile__("bic %0, %0, #0x2":"=r"(i));
+ __asm__ __volatile__("mcr p15, 0, %0, c1, c0, 1":"=r"(i));
+ } else {
+ /* Save r0, r12 and restore them after usage */
+ __asm__ __volatile__("mov %0, r12":"=r"(j));
+ __asm__ __volatile__("mov %0, r0":"=r"(i));
+
+ /*
+ * GP Device ROM code API usage here
+ * r12 = AUXCR Write function and r0 value
+ */
+ __asm__ __volatile__("mov r12, #0x3");
+ __asm__ __volatile__("mrc p15, 0, r0, c1, c0, 1");
+ __asm__ __volatile__("bic r0, r0, #0x2");
+ /* SMI instruction to call ROM Code API */
+ __asm__ __volatile__(".word 0xE1600070");
+ __asm__ __volatile__("mov r0, %0":"=r"(i));
+ __asm__ __volatile__("mov r12, %0":"=r"(j));
+ }
+}
+
+int icache_status(void)
+{
+ return (read_p15_c1() & C1_IC) != 0;
+}
+
+static void cache_flush(void)
+{
+ asm ("mcr p15, 0, %0, c7, c5, 0": :"r" (0));
+}
+
--- /dev/null
+#
+# (C) Copyright 2000-2003
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(SOC).a
+
+SOBJS := lowlevel_init.o
+COBJS := sys_info.o board.o clock.o interrupts.o mem.o syslib.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS))
+
+all: $(obj).depend $(LIB)
+
+$(LIB): $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+/*
+ *
+ * Common board functions for OMAP3 based boards.
+ *
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ * Sunil Kumar <sunilsaini05@gmail.com>
+ * Shashi Ranjan <shashiranjanmca05@gmail.com>
+ *
+ * Derived from Beagle Board and 3430 SDP code by
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
+
+extern omap3_sysinfo sysinfo;
+
+/******************************************************************************
+ * Routine: delay
+ * Description: spinning delay to use before udelay works
+ *****************************************************************************/
+static inline void delay(unsigned long loops)
+{
+ __asm__ volatile ("1:\n" "subs %0, %1, #1\n"
+ "bne 1b":"=r" (loops):"0"(loops));
+}
+
+/******************************************************************************
+ * Routine: secure_unlock
+ * Description: Setup security registers for access
+ * (GP Device only)
+ *****************************************************************************/
+void secure_unlock_mem(void)
+{
+ pm_t *pm_rt_ape_base = (pm_t *)PM_RT_APE_BASE_ADDR_ARM;
+ pm_t *pm_gpmc_base = (pm_t *)PM_GPMC_BASE_ADDR_ARM;
+ pm_t *pm_ocm_ram_base = (pm_t *)PM_OCM_RAM_BASE_ADDR_ARM;
+ pm_t *pm_iva2_base = (pm_t *)PM_IVA2_BASE_ADDR_ARM;
+ sms_t *sms_base = (sms_t *)OMAP34XX_SMS_BASE;
+
+ /* Protection Module Register Target APE (PM_RT) */
+ writel(UNLOCK_1, &pm_rt_ape_base->req_info_permission_1);
+ writel(UNLOCK_1, &pm_rt_ape_base->read_permission_0);
+ writel(UNLOCK_1, &pm_rt_ape_base->wirte_permission_0);
+ writel(UNLOCK_2, &pm_rt_ape_base->addr_match_1);
+
+ writel(UNLOCK_3, &pm_gpmc_base->req_info_permission_0);
+ writel(UNLOCK_3, &pm_gpmc_base->read_permission_0);
+ writel(UNLOCK_3, &pm_gpmc_base->wirte_permission_0);
+
+ writel(UNLOCK_3, &pm_ocm_ram_base->req_info_permission_0);
+ writel(UNLOCK_3, &pm_ocm_ram_base->read_permission_0);
+ writel(UNLOCK_3, &pm_ocm_ram_base->wirte_permission_0);
+ writel(UNLOCK_2, &pm_ocm_ram_base->addr_match_2);
+
+ /* IVA Changes */
+ writel(UNLOCK_3, &pm_iva2_base->req_info_permission_0);
+ writel(UNLOCK_3, &pm_iva2_base->read_permission_0);
+ writel(UNLOCK_3, &pm_iva2_base->wirte_permission_0);
+
+ /* SDRC region 0 public */
+ writel(UNLOCK_1, &sms_base->rg_att0);
+}
+
+/******************************************************************************
+ * Routine: secureworld_exit()
+ * Description: If chip is EMU and boot type is external
+ * configure secure registers and exit secure world
+ * general use.
+ *****************************************************************************/
+void secureworld_exit()
+{
+ unsigned long i;
+
+ /* configrue non-secure access control register */
+ __asm__ __volatile__("mrc p15, 0, %0, c1, c1, 2":"=r"(i));
+ /* enabling co-processor CP10 and CP11 accesses in NS world */
+ __asm__ __volatile__("orr %0, %0, #0xC00":"=r"(i));
+ /*
+ * allow allocation of locked TLBs and L2 lines in NS world
+ * allow use of PLE registers in NS world also
+ */
+ __asm__ __volatile__("orr %0, %0, #0x70000":"=r"(i));
+ __asm__ __volatile__("mcr p15, 0, %0, c1, c1, 2":"=r"(i));
+
+ /* Enable ASA in ACR register */
+ __asm__ __volatile__("mrc p15, 0, %0, c1, c0, 1":"=r"(i));
+ __asm__ __volatile__("orr %0, %0, #0x10":"=r"(i));
+ __asm__ __volatile__("mcr p15, 0, %0, c1, c0, 1":"=r"(i));
+
+ /* Exiting secure world */
+ __asm__ __volatile__("mrc p15, 0, %0, c1, c1, 0":"=r"(i));
+ __asm__ __volatile__("orr %0, %0, #0x31":"=r"(i));
+ __asm__ __volatile__("mcr p15, 0, %0, c1, c1, 0":"=r"(i));
+}
+
+/******************************************************************************
+ * Routine: setup_auxcr()
+ * Description: Write to AuxCR desired value using SMI.
+ * general use.
+ *****************************************************************************/
+void setup_auxcr()
+{
+ unsigned long i;
+ volatile unsigned int j;
+ /* Save r0, r12 and restore them after usage */
+ __asm__ __volatile__("mov %0, r12":"=r"(j));
+ __asm__ __volatile__("mov %0, r0":"=r"(i));
+
+ /*
+ * GP Device ROM code API usage here
+ * r12 = AUXCR Write function and r0 value
+ */
+ __asm__ __volatile__("mov r12, #0x3");
+ __asm__ __volatile__("mrc p15, 0, r0, c1, c0, 1");
+ /* Enabling ASA */
+ __asm__ __volatile__("orr r0, r0, #0x10");
+ /* Enable L1NEON */
+ __asm__ __volatile__("orr r0, r0, #1 << 5");
+ /* SMI instruction to call ROM Code API */
+ __asm__ __volatile__(".word 0xE1600070");
+ __asm__ __volatile__("mov r0, %0":"=r"(i));
+ __asm__ __volatile__("mov r12, %0":"=r"(j));
+}
+
+/******************************************************************************
+ * Routine: try_unlock_sram()
+ * Description: If chip is GP/EMU(special) type, unlock the SRAM for
+ * general use.
+ *****************************************************************************/
+void try_unlock_memory()
+{
+ int mode;
+ int in_sdram = is_running_in_sdram();
+
+ /*
+ * if GP device unlock device SRAM for general use
+ * secure code breaks for Secure/Emulation device - HS/E/T
+ */
+ mode = get_device_type();
+ if (mode == GP_DEVICE)
+ secure_unlock_mem();
+
+ /*
+ * If device is EMU and boot is XIP external booting
+ * Unlock firewalls and disable L2 and put chip
+ * out of secure world
+ *
+ * Assuming memories are unlocked by the demon who put us in SDRAM
+ */
+ if ((mode <= EMU_DEVICE) && (get_boot_type() == 0x1F)
+ && (!in_sdram)) {
+ secure_unlock_mem();
+ secureworld_exit();
+ }
+
+ return;
+}
+
+/******************************************************************************
+ * Routine: s_init
+ * Description: Does early system init of muxing and clocks.
+ * - Called path is with SRAM stack.
+ *****************************************************************************/
+void s_init(void)
+{
+ int in_sdram = is_running_in_sdram();
+
+ watchdog_init();
+
+ try_unlock_memory();
+
+ /*
+ * Right now flushing at low MPU speed.
+ * Need to move after clock init
+ */
+ v7_flush_dcache_all(get_device_type());
+#ifndef CONFIG_ICACHE_OFF
+ icache_enable();
+#endif
+
+#ifdef CONFIG_L2_OFF
+ l2cache_disable();
+#else
+ l2cache_enable();
+#endif
+ /*
+ * Writing to AuxCR in U-boot using SMI for GP DEV
+ * Currently SMI in Kernel on ES2 devices seems to have an issue
+ * Once that is resolved, we can postpone this config to kernel
+ */
+ if (get_device_type() == GP_DEVICE)
+ setup_auxcr();
+
+ set_muxconf_regs();
+ delay(100);
+
+ prcm_init();
+
+ per_clocks_enable();
+
+ if (!in_sdram)
+ sdrc_init();
+}
+
+/******************************************************************************
+ * Routine: wait_for_command_complete
+ * Description: Wait for posting to finish on watchdog
+ *****************************************************************************/
+void wait_for_command_complete(watchdog_t *wd_base)
+{
+ int pending = 1;
+ do {
+ pending = readl(&wd_base->wwps);
+ } while (pending);
+}
+
+/******************************************************************************
+ * Routine: watchdog_init
+ * Description: Shut down watch dogs
+ *****************************************************************************/
+void watchdog_init(void)
+{
+ watchdog_t *wd2_base = (watchdog_t *)WD2_BASE;
+ prcm_t *prcm_base = (prcm_t *)PRCM_BASE;
+
+ /*
+ * There are 3 watch dogs WD1=Secure, WD2=MPU, WD3=IVA. WD1 is
+ * either taken care of by ROM (HS/EMU) or not accessible (GP).
+ * We need to take care of WD2-MPU or take a PRCM reset. WD3
+ * should not be running and does not generate a PRCM reset.
+ */
+
+ sr32(&prcm_base->fclken_wkup, 5, 1, 1);
+ sr32(&prcm_base->iclken_wkup, 5, 1, 1);
+ wait_on_value(ST_WDT2, 0x20, &prcm_base->idlest_wkup, 5);
+
+ writel(WD_UNLOCK1, &wd2_base->wspr);
+ wait_for_command_complete(wd2_base);
+ writel(WD_UNLOCK2, &wd2_base->wspr);
+}
+
+/******************************************************************************
+ * Routine: dram_init
+ * Description: sets uboots idea of sdram size
+ *****************************************************************************/
+int dram_init(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+ unsigned int size0 = 0, size1 = 0;
+ u32 btype;
+
+ btype = get_board_type();
+
+ display_board_info(btype);
+
+ /*
+ * If a second bank of DDR is attached to CS1 this is
+ * where it can be started. Early init code will init
+ * memory on CS0.
+ */
+ if ((sysinfo.mtype == DDR_COMBO) || (sysinfo.mtype == DDR_STACKED)) {
+ do_sdrc_init(CS1, NOT_EARLY);
+ make_cs1_contiguous();
+ }
+
+ size0 = get_sdr_cs_size(CS0);
+ size1 = get_sdr_cs_size(CS1);
+
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = size0;
+ gd->bd->bi_dram[1].start = PHYS_SDRAM_1 + get_sdr_cs_offset(CS1);
+ gd->bd->bi_dram[1].size = size1;
+
+ return 0;
+}
+
+/******************************************************************************
+ * Dummy function to handle errors for EABI incompatibility
+ *****************************************************************************/
+void raise(void)
+{
+}
+
+/******************************************************************************
+ * Dummy function to handle errors for EABI incompatibility
+ *****************************************************************************/
+void abort(void)
+{
+}
+
+#ifdef CONFIG_NAND_OMAP_GPMC
+/******************************************************************************
+ * OMAP3 specific command to switch between NAND HW and SW ecc
+ *****************************************************************************/
+static int do_switch_ecc(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+ if (argc != 2)
+ goto usage;
+ if (strncmp(argv[1], "hw", 2) == 0)
+ omap_nand_switch_ecc(1);
+ else if (strncmp(argv[1], "sw", 2) == 0)
+ omap_nand_switch_ecc(0);
+ else
+ goto usage;
+
+ return 0;
+
+usage:
+ printf ("Usage: nandecc %s\n", cmdtp->help);
+ return 1;
+}
+
+U_BOOT_CMD(
+ nandecc, 2, 1, do_switch_ecc,
+ "nandecc - switch OMAP3 NAND ECC calculation algorithm\n",
+ "[hw/sw] - Switch between NAND hardware (hw) or software (sw) ecc algorithm\n"
+ );
+
+#endif /* CONFIG_NAND_OMAP_GPMC */
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ * Manikandan Pillai <mani.pillai@ti.com>
+ *
+ * Derived from Beagle Board and OMAP3 SDP code by
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/clocks.h>
+#include <asm/arch/clocks_omap3.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/sys_proto.h>
+#include <environment.h>
+#include <command.h>
+
+/******************************************************************************
+ * get_sys_clk_speed() - determine reference oscillator speed
+ * based on known 32kHz clock and gptimer.
+ *****************************************************************************/
+u32 get_osc_clk_speed(void)
+{
+ u32 start, cstart, cend, cdiff, val;
+ prcm_t *prcm_base = (prcm_t *)PRCM_BASE;
+ prm_t *prm_base = (prm_t *)PRM_BASE;
+ gptimer_t *gpt1_base = (gptimer_t *)OMAP34XX_GPT1;
+ s32ktimer_t *s32k_base = (s32ktimer_t *)SYNC_32KTIMER_BASE;
+
+ val = readl(&prm_base->clksrc_ctrl);
+
+ /* If SYS_CLK is being divided by 2, remove for now */
+ val = (val & (~SYSCLKDIV_2)) | SYSCLKDIV_1;
+ writel(val, &prm_base->clksrc_ctrl);
+
+ /* enable timer2 */
+ val = readl(&prcm_base->clksel_wkup) | CLKSEL_GPT1;
+
+ /* select sys_clk for GPT1 */
+ writel(val, &prcm_base->clksel_wkup);
+
+ /* Enable I and F Clocks for GPT1 */
+ val = readl(&prcm_base->iclken_wkup) | EN_GPT1 | EN_32KSYNC;
+ writel(val, &prcm_base->iclken_wkup);
+ val = readl(&prcm_base->fclken_wkup) | EN_GPT1;
+ writel(val, &prcm_base->fclken_wkup);
+
+ writel(0, &gpt1_base->tldr); /* start counting at 0 */
+ writel(GPT_EN, &gpt1_base->tclr); /* enable clock */
+
+ /* enable 32kHz source, determine sys_clk via gauging */
+
+ /* start time in 20 cycles */
+ start = 20 + readl(&s32k_base->s32k_cr);
+
+ /* dead loop till start time */
+ while (readl(&s32k_base->s32k_cr) < start);
+
+ /* get start sys_clk count */
+ cstart = readl(&gpt1_base->tcrr);
+
+ /* wait for 40 cycles */
+ while (readl(&s32k_base->s32k_cr) < (start + 20)) ;
+ cend = readl(&gpt1_base->tcrr); /* get end sys_clk count */
+ cdiff = cend - cstart; /* get elapsed ticks */
+
+ /* based on number of ticks assign speed */
+ if (cdiff > 19000)
+ return S38_4M;
+ else if (cdiff > 15200)
+ return S26M;
+ else if (cdiff > 13000)
+ return S24M;
+ else if (cdiff > 9000)
+ return S19_2M;
+ else if (cdiff > 7600)
+ return S13M;
+ else
+ return S12M;
+}
+
+/******************************************************************************
+ * get_sys_clkin_sel() - returns the sys_clkin_sel field value based on
+ * input oscillator clock frequency.
+ *****************************************************************************/
+void get_sys_clkin_sel(u32 osc_clk, u32 *sys_clkin_sel)
+{
+ switch(osc_clk) {
+ case S38_4M:
+ *sys_clkin_sel = 4;
+ break;
+ case S26M:
+ *sys_clkin_sel = 3;
+ break;
+ case S19_2M:
+ *sys_clkin_sel = 2;
+ break;
+ case S13M:
+ *sys_clkin_sel = 1;
+ break;
+ case S12M:
+ default:
+ *sys_clkin_sel = 0;
+ }
+}
+
+/******************************************************************************
+ * prcm_init() - inits clocks for PRCM as defined in clocks.h
+ * called from SRAM, or Flash (using temp SRAM stack).
+ *****************************************************************************/
+void prcm_init(void)
+{
+ void (*f_lock_pll) (u32, u32, u32, u32);
+ int xip_safe, p0, p1, p2, p3;
+ u32 osc_clk = 0, sys_clkin_sel;
+ u32 clk_index, sil_index;
+ prm_t *prm_base = (prm_t *)PRM_BASE;
+ prcm_t *prcm_base = (prcm_t *)PRCM_BASE;
+ dpll_param *dpll_param_p;
+
+ f_lock_pll = (void *) ((u32) &_end_vect - (u32) &_start +
+ SRAM_VECT_CODE);
+
+ xip_safe = is_running_in_sram();
+
+ /*
+ * Gauge the input clock speed and find out the sys_clkin_sel
+ * value corresponding to the input clock.
+ */
+ osc_clk = get_osc_clk_speed();
+ get_sys_clkin_sel(osc_clk, &sys_clkin_sel);
+
+ /* set input crystal speed */
+ sr32(&prm_base->clksel, 0, 3, sys_clkin_sel);
+
+ /* If the input clock is greater than 19.2M always divide/2 */
+ if (sys_clkin_sel > 2) {
+ /* input clock divider */
+ sr32(&prm_base->clksrc_ctrl, 6, 2, 2);
+ clk_index = sys_clkin_sel / 2;
+ } else {
+ /* input clock divider */
+ sr32(&prm_base->clksrc_ctrl, 6, 2, 1);
+ clk_index = sys_clkin_sel;
+ }
+
+ /*
+ * The DPLL tables are defined according to sysclk value and
+ * silicon revision. The clk_index value will be used to get
+ * the values for that input sysclk from the DPLL param table
+ * and sil_index will get the values for that SysClk for the
+ * appropriate silicon rev.
+ */
+ sil_index = get_cpu_rev() - 1;
+
+ /* Unlock MPU DPLL (slows things down, and needed later) */
+ sr32(&prcm_base->clken_pll_mpu, 0, 3, PLL_LOW_POWER_BYPASS);
+ wait_on_value(ST_MPU_CLK, 0, &prcm_base->idlest_pll_mpu, LDELAY);
+
+ /* Getting the base address of Core DPLL param table */
+ dpll_param_p = (dpll_param *) get_core_dpll_param();
+
+ /* Moving it to the right sysclk and ES rev base */
+ dpll_param_p = dpll_param_p + 3 * clk_index + sil_index;
+ if (xip_safe) {
+ /*
+ * CORE DPLL
+ * sr32(CM_CLKSEL2_EMU) set override to work when asleep
+ */
+ sr32(&prcm_base->clken_pll, 0, 3, PLL_FAST_RELOCK_BYPASS);
+ wait_on_value(ST_CORE_CLK, 0, &prcm_base->idlest_ckgen,
+ LDELAY);
+
+ /*
+ * For OMAP3 ES1.0 Errata 1.50, default value directly doesn't
+ * work. write another value and then default value.
+ */
+
+ /* m3x2 */
+ sr32(&prcm_base->clksel1_emu, 16, 5, CORE_M3X2 + 1);
+ /* m3x2 */
+ sr32(&prcm_base->clksel1_emu, 16, 5, CORE_M3X2);
+ /* Set M2 */
+ sr32(&prcm_base->clksel1_pll, 27, 2, dpll_param_p->m2);
+ /* Set M */
+ sr32(&prcm_base->clksel1_pll, 16, 11, dpll_param_p->m);
+ /* Set N */
+ sr32(&prcm_base->clksel1_pll, 8, 7, dpll_param_p->n);
+ /* 96M Src */
+ sr32(&prcm_base->clksel1_pll, 6, 1, 0);
+ /* ssi */
+ sr32(&prcm_base->clksel_core, 8, 4, CORE_SSI_DIV);
+ /* fsusb */
+ sr32(&prcm_base->clksel_core, 4, 2, CORE_FUSB_DIV);
+ /* l4 */
+ sr32(&prcm_base->clksel_core, 2, 2, CORE_L4_DIV);
+ /* l3 */
+ sr32(&prcm_base->clksel_core, 0, 2, CORE_L3_DIV);
+ /* gfx */
+ sr32(&prcm_base->clksel_gfx, 0, 3, GFX_DIV);
+ /* reset mgr */
+ sr32(&prcm_base->clksel_wkup, 1, 2, WKUP_RSM);
+ /* FREQSEL */
+ sr32(&prcm_base->clken_pll, 4, 4, dpll_param_p->fsel);
+ /* lock mode */
+ sr32(&prcm_base->clken_pll, 0, 3, PLL_LOCK);
+
+ wait_on_value(ST_CORE_CLK, 1, &prcm_base->idlest_ckgen,
+ LDELAY);
+ } else if (is_running_in_flash()) {
+ /*
+ * if running from flash, jump to small relocated code
+ * area in SRAM.
+ */
+ p0 = readl(&prcm_base->clken_pll);
+ sr32(&p0, 0, 3, PLL_FAST_RELOCK_BYPASS);
+ sr32(&p0, 4, 4, dpll_param_p->fsel); /* FREQSEL */
+
+ p1 = readl(&prcm_base->clksel1_pll);
+ sr32(&p1, 27, 2, dpll_param_p->m2); /* Set M2 */
+ sr32(&p1, 16, 11, dpll_param_p->m); /* Set M */
+ sr32(&p1, 8, 7, dpll_param_p->n); /* Set N */
+ sr32(&p1, 6, 1, 0); /* set source for 96M */
+
+ p2 = readl(&prcm_base->clksel_core);
+ sr32(&p2, 8, 4, CORE_SSI_DIV); /* ssi */
+ sr32(&p2, 4, 2, CORE_FUSB_DIV); /* fsusb */
+ sr32(&p2, 2, 2, CORE_L4_DIV); /* l4 */
+ sr32(&p2, 0, 2, CORE_L3_DIV); /* l3 */
+
+ p3 = (u32)&prcm_base->idlest_ckgen;
+
+ (*f_lock_pll) (p0, p1, p2, p3);
+ }
+
+ /* PER DPLL */
+ sr32(&prcm_base->clken_pll, 16, 3, PLL_STOP);
+ wait_on_value(ST_PERIPH_CLK, 0, &prcm_base->idlest_ckgen, LDELAY);
+
+ /* Getting the base address to PER DPLL param table */
+
+ /* Set N */
+ dpll_param_p = (dpll_param *) get_per_dpll_param();
+
+ /* Moving it to the right sysclk base */
+ dpll_param_p = dpll_param_p + clk_index;
+
+ /*
+ * Errata 1.50 Workaround for OMAP3 ES1.0 only
+ * If using default divisors, write default divisor + 1
+ * and then the actual divisor value
+ */
+ sr32(&prcm_base->clksel1_emu, 24, 5, PER_M6X2 + 1); /* set M6 */
+ sr32(&prcm_base->clksel1_emu, 24, 5, PER_M6X2); /* set M6 */
+ sr32(&prcm_base->clksel_cam, 0, 5, PER_M5X2 + 1); /* set M5 */
+ sr32(&prcm_base->clksel_cam, 0, 5, PER_M5X2); /* set M5 */
+ sr32(&prcm_base->clksel_dss, 0, 5, PER_M4X2 + 1); /* set M4 */
+ sr32(&prcm_base->clksel_dss, 0, 5, PER_M4X2); /* set M4 */
+ sr32(&prcm_base->clksel_dss, 8, 5, PER_M3X2 + 1); /* set M3 */
+ sr32(&prcm_base->clksel_dss, 8, 5, PER_M3X2); /* set M3 */
+ sr32(&prcm_base->clksel3_pll, 0, 5, dpll_param_p->m2 + 1); /* set M2 */
+ sr32(&prcm_base->clksel3_pll, 0, 5, dpll_param_p->m2); /* set M2 */
+ /* Workaround end */
+
+ sr32(&prcm_base->clksel2_pll, 8, 11, dpll_param_p->m); /* set m */
+ sr32(&prcm_base->clksel2_pll, 0, 7, dpll_param_p->n); /* set n */
+ sr32(&prcm_base->clken_pll, 20, 4, dpll_param_p->fsel); /* FREQSEL */
+ sr32(&prcm_base->clken_pll, 16, 3, PLL_LOCK); /* lock mode */
+ wait_on_value(ST_PERIPH_CLK, 2, &prcm_base->idlest_ckgen, LDELAY);
+
+ /* Getting the base address to MPU DPLL param table */
+ dpll_param_p = (dpll_param *) get_mpu_dpll_param();
+
+ /* Moving it to the right sysclk and ES rev base */
+ dpll_param_p = dpll_param_p + 3 * clk_index + sil_index;
+
+ /* MPU DPLL (unlocked already) */
+
+ /* Set M2 */
+ sr32(&prcm_base->clksel2_pll_mpu, 0, 5, dpll_param_p->m2);
+ /* Set M */
+ sr32(&prcm_base->clksel1_pll_mpu, 8, 11, dpll_param_p->m);
+ /* Set N */
+ sr32(&prcm_base->clksel1_pll_mpu, 0, 7, dpll_param_p->n);
+ /* FREQSEL */
+ sr32(&prcm_base->clken_pll_mpu, 4, 4, dpll_param_p->fsel);
+ /* lock mode */
+ sr32(&prcm_base->clken_pll_mpu, 0, 3, PLL_LOCK);
+ wait_on_value(ST_MPU_CLK, 1, &prcm_base->idlest_pll_mpu, LDELAY);
+
+ /* Getting the base address to IVA DPLL param table */
+ dpll_param_p = (dpll_param *) get_iva_dpll_param();
+
+ /* Moving it to the right sysclk and ES rev base */
+ dpll_param_p = dpll_param_p + 3 * clk_index + sil_index;
+
+ /* IVA DPLL (set to 12*20=240MHz) */
+ sr32(&prcm_base->clken_pll_iva2, 0, 3, PLL_STOP);
+ wait_on_value(ST_IVA2_CLK, 0, &prcm_base->idlest_pll_iva2, LDELAY);
+ /* set M2 */
+ sr32(&prcm_base->clksel2_pll_iva2, 0, 5, dpll_param_p->m2);
+ /* set M */
+ sr32(&prcm_base->clksel1_pll_iva2, 8, 11, dpll_param_p->m);
+ /* set N */
+ sr32(&prcm_base->clksel1_pll_iva2, 0, 7, dpll_param_p->n);
+ /* FREQSEL */
+ sr32(&prcm_base->clken_pll_iva2, 4, 4, dpll_param_p->fsel);
+ /* lock mode */
+ sr32(&prcm_base->clken_pll_iva2, 0, 3, PLL_LOCK);
+ wait_on_value(ST_IVA2_CLK, 1, &prcm_base->idlest_pll_iva2, LDELAY);
+
+ /* Set up GPTimers to sys_clk source only */
+ sr32(&prcm_base->clksel_per, 0, 8, 0xff);
+ sr32(&prcm_base->clksel_wkup, 0, 1, 1);
+
+ sdelay(5000);
+}
+
+/******************************************************************************
+ * peripheral_enable() - Enable the clks & power for perifs (GPT2, UART1,...)
+ *****************************************************************************/
+void per_clocks_enable(void)
+{
+ prcm_t *prcm_base = (prcm_t *)PRCM_BASE;
+
+ /* Enable GP2 timer. */
+ sr32(&prcm_base->clksel_per, 0, 1, 0x1); /* GPT2 = sys clk */
+ sr32(&prcm_base->iclken_per, 3, 1, 0x1); /* ICKen GPT2 */
+ sr32(&prcm_base->fclken_per, 3, 1, 0x1); /* FCKen GPT2 */
+
+#ifdef CONFIG_SYS_NS16550
+ /* Enable UART1 clocks */
+ sr32(&prcm_base->fclken1_core, 13, 1, 0x1);
+ sr32(&prcm_base->iclken1_core, 13, 1, 0x1);
+
+ /* UART 3 Clocks */
+ sr32(&prcm_base->fclken_per, 11, 1, 0x1);
+ sr32(&prcm_base->iclken_per, 11, 1, 0x1);
+#endif
+#ifdef CONFIG_DRIVER_OMAP34XX_I2C
+ /* Turn on all 3 I2C clocks */
+ sr32(&prcm_base->fclken1_core, 15, 3, 0x7);
+ sr32(&prcm_base->iclken1_core, 15, 3, 0x7); /* I2C1,2,3 = on */
+#endif
+ /* Enable the ICLK for 32K Sync Timer as its used in udelay */
+ sr32(&prcm_base->iclken_wkup, 2, 1, 0x1);
+
+ sr32(&prcm_base->fclken_iva2, 0, 32, FCK_IVA2_ON);
+ sr32(&prcm_base->fclken1_core, 0, 32, FCK_CORE1_ON);
+ sr32(&prcm_base->iclken1_core, 0, 32, ICK_CORE1_ON);
+ sr32(&prcm_base->iclken2_core, 0, 32, ICK_CORE2_ON);
+ sr32(&prcm_base->fclken_wkup, 0, 32, FCK_WKUP_ON);
+ sr32(&prcm_base->iclken_wkup, 0, 32, ICK_WKUP_ON);
+ sr32(&prcm_base->fclken_dss, 0, 32, FCK_DSS_ON);
+ sr32(&prcm_base->iclken_dss, 0, 32, ICK_DSS_ON);
+ sr32(&prcm_base->fclken_cam, 0, 32, FCK_CAM_ON);
+ sr32(&prcm_base->iclken_cam, 0, 32, ICK_CAM_ON);
+ sr32(&prcm_base->fclken_per, 0, 32, FCK_PER_ON);
+ sr32(&prcm_base->iclken_per, 0, 32, ICK_PER_ON);
+
+ sdelay(1000);
+}
--- /dev/null
+#
+# (C) Copyright 2002
+# Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+PLATFORM_RELFLAGS += -fno-strict-aliasing -fno-common -ffixed-r8 \
+ -msoft-float
+
+# Make ARMv5 to allow more compilers to work, even though its v7a.
+PLATFORM_CPPFLAGS += -march=armv5
+# =========================================================================
+#
+# Supply options according to compiler version
+#
+# =========================================================================
+PLATFORM_CPPFLAGS +=$(call cc-option)
+PLATFORM_CPPFLAGS +=$(call cc-option,-mno-thumb-interwork,)
+PLATFORM_RELFLAGS +=$(call cc-option,-mshort-load-bytes,\
+ $(call cc-option,-malignment-traps,))
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Texas Instruments
+ *
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Moahmmed Khasim <khasim@ti.com>
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ * Alex Zuepke <azu@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/proc-armv/ptrace.h>
+
+#define TIMER_LOAD_VAL 0
+
+#ifdef CONFIG_USE_IRQ
+/* enable IRQ interrupts */
+void enable_interrupts(void)
+{
+ unsigned long temp;
+ __asm__ __volatile__("mrs %0, cpsr\n"
+ "bic %0, %0, #0x80\n" "msr cpsr_c, %0":"=r"(temp)
+ ::"memory");
+}
+
+/*
+ * disable IRQ/FIQ interrupts
+ * returns true if interrupts had been enabled before we disabled them
+ */
+int disable_interrupts(void)
+{
+ unsigned long old, temp;
+ __asm__ __volatile__("mrs %0, cpsr\n"
+ "orr %1, %0, #0xc0\n"
+ "msr cpsr_c, %1":"=r"(old), "=r"(temp)
+ ::"memory");
+ return (old & 0x80) == 0;
+}
+#else
+void enable_interrupts(void)
+{
+ return;
+}
+int disable_interrupts(void)
+{
+ return 0;
+}
+#endif
+
+void bad_mode(void)
+{
+ panic("Resetting CPU ...\n");
+ reset_cpu(0);
+}
+
+void show_regs(struct pt_regs *regs)
+{
+ unsigned long flags;
+ const char *processor_modes[] = {
+ "USER_26", "FIQ_26", "IRQ_26", "SVC_26",
+ "UK4_26", "UK5_26", "UK6_26", "UK7_26",
+ "UK8_26", "UK9_26", "UK10_26", "UK11_26",
+ "UK12_26", "UK13_26", "UK14_26", "UK15_26",
+ "USER_32", "FIQ_32", "IRQ_32", "SVC_32",
+ "UK4_32", "UK5_32", "UK6_32", "ABT_32",
+ "UK8_32", "UK9_32", "UK10_32", "UND_32",
+ "UK12_32", "UK13_32", "UK14_32", "SYS_32",
+ };
+
+ flags = condition_codes(regs);
+
+ printf("pc : [<%08lx>] lr : [<%08lx>]\n"
+ "sp : %08lx ip : %08lx fp : %08lx\n",
+ instruction_pointer(regs),
+ regs->ARM_lr, regs->ARM_sp, regs->ARM_ip, regs->ARM_fp);
+ printf("r10: %08lx r9 : %08lx r8 : %08lx\n",
+ regs->ARM_r10, regs->ARM_r9, regs->ARM_r8);
+ printf("r7 : %08lx r6 : %08lx r5 : %08lx r4 : %08lx\n",
+ regs->ARM_r7, regs->ARM_r6, regs->ARM_r5, regs->ARM_r4);
+ printf("r3 : %08lx r2 : %08lx r1 : %08lx r0 : %08lx\n",
+ regs->ARM_r3, regs->ARM_r2, regs->ARM_r1, regs->ARM_r0);
+ printf("Flags: %c%c%c%c",
+ flags & CC_N_BIT ? 'N' : 'n',
+ flags & CC_Z_BIT ? 'Z' : 'z',
+ flags & CC_C_BIT ? 'C' : 'c', flags & CC_V_BIT ? 'V' : 'v');
+ printf(" IRQs %s FIQs %s Mode %s%s\n",
+ interrupts_enabled(regs) ? "on" : "off",
+ fast_interrupts_enabled(regs) ? "on" : "off",
+ processor_modes[processor_mode(regs)],
+ thumb_mode(regs) ? " (T)" : "");
+}
+
+void do_undefined_instruction(struct pt_regs *pt_regs)
+{
+ printf("undefined instruction\n");
+ show_regs(pt_regs);
+ bad_mode();
+}
+
+void do_software_interrupt(struct pt_regs *pt_regs)
+{
+ printf("software interrupt\n");
+ show_regs(pt_regs);
+ bad_mode();
+}
+
+void do_prefetch_abort(struct pt_regs *pt_regs)
+{
+ printf("prefetch abort\n");
+ show_regs(pt_regs);
+ bad_mode();
+}
+
+void do_data_abort(struct pt_regs *pt_regs)
+{
+ printf("data abort\n");
+ show_regs(pt_regs);
+ bad_mode();
+}
+
+void do_not_used(struct pt_regs *pt_regs)
+{
+ printf("not used\n");
+ show_regs(pt_regs);
+ bad_mode();
+}
+
+void do_fiq(struct pt_regs *pt_regs)
+{
+ printf("fast interrupt request\n");
+ show_regs(pt_regs);
+ bad_mode();
+}
+
+void do_irq(struct pt_regs *pt_regs)
+{
+ printf("interrupt request\n");
+ show_regs(pt_regs);
+ bad_mode();
+}
+
+
+static ulong timestamp;
+static ulong lastinc;
+static gptimer_t *timer_base = (gptimer_t *)CONFIG_SYS_TIMERBASE;
+
+/* nothing really to do with interrupts, just starts up a counter. */
+int interrupt_init(void)
+{
+ /* start the counter ticking up, reload value on overflow */
+ writel(TIMER_LOAD_VAL, &timer_base->tldr);
+ /* enable timer */
+ writel((CONFIG_SYS_PVT << 2) | TCLR_PRE | TCLR_AR | TCLR_ST,
+ &timer_base->tclr);
+
+ reset_timer_masked(); /* init the timestamp and lastinc value */
+
+ return 0;
+}
+
+/*
+ * timer without interrupts
+ */
+void reset_timer(void)
+{
+ reset_timer_masked();
+}
+
+ulong get_timer(ulong base)
+{
+ return get_timer_masked() - base;
+}
+
+void set_timer(ulong t)
+{
+ timestamp = t;
+}
+
+/* delay x useconds AND perserve advance timstamp value */
+void udelay(unsigned long usec)
+{
+ ulong tmo, tmp;
+
+ /* if "big" number, spread normalization to seconds */
+ if (usec >= 1000) {
+ /* if "big" number, spread normalization to seconds */
+ tmo = usec / 1000;
+ /* find number of "ticks" to wait to achieve target */
+ tmo *= CONFIG_SYS_HZ;
+ tmo /= 1000; /* finish normalize. */
+ } else {/* else small number, don't kill it prior to HZ multiply */
+ tmo = usec * CONFIG_SYS_HZ;
+ tmo /= (1000 * 1000);
+ }
+
+ tmp = get_timer(0); /* get current timestamp */
+ /* if setting this forward will roll time stamp */
+ if ((tmo + tmp + 1) < tmp)
+ /* reset "advancing" timestamp to 0, set lastinc value */
+ reset_timer_masked();
+ else
+ tmo += tmp; /* else, set advancing stamp wake up time */
+ while (get_timer_masked() < tmo) /* loop till event */
+ /*NOP*/;
+}
+
+void reset_timer_masked(void)
+{
+ /* reset time, capture current incrementer value time */
+ lastinc = readl(&timer_base->tcrr);
+ timestamp = 0; /* start "advancing" time stamp from 0 */
+}
+
+ulong get_timer_masked(void)
+{
+ ulong now = readl(&timer_base->tcrr); /* current tick value */
+
+ if (now >= lastinc) /* normal mode (non roll) */
+ /* move stamp fordward with absoulte diff ticks */
+ timestamp += (now - lastinc);
+ else /* we have rollover of incrementer */
+ timestamp += (0xFFFFFFFF - lastinc) + now;
+ lastinc = now;
+ return timestamp;
+}
+
+/* waits specified delay value and resets timestamp */
+void udelay_masked(unsigned long usec)
+{
+ ulong tmo;
+ ulong endtime;
+ signed long diff;
+
+ /* if "big" number, spread normalization to seconds */
+ if (usec >= 1000) {
+ /* start to normalize for usec to ticks per sec */
+ tmo = usec / 1000;
+ /* find number of "ticks" to wait to achieve target */
+ tmo *= CONFIG_SYS_HZ;
+ tmo /= 1000; /* finish normalize. */
+ } else { /* else small number, */
+ /* don't kill it prior to HZ multiply */
+ tmo = usec * CONFIG_SYS_HZ;
+ tmo /= (1000 * 1000);
+ }
+ endtime = get_timer_masked() + tmo;
+
+ do {
+ ulong now = get_timer_masked();
+ diff = endtime - now;
+ } while (diff >= 0);
+}
+
+/*
+ * This function is derived from PowerPC code (read timebase as long long).
+ * On ARM it just returns the timer value.
+ */
+unsigned long long get_ticks(void)
+{
+ return get_timer(0);
+}
+
+/*
+ * This function is derived from PowerPC code (timebase clock frequency).
+ * On ARM it returns the number of timer ticks per second.
+ */
+ulong get_tbclk(void)
+{
+ ulong tbclk;
+ tbclk = CONFIG_SYS_HZ;
+ return tbclk;
+}
--- /dev/null
+/*
+ * Board specific setup info
+ *
+ * (C) Copyright 2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Initial Code by:
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/clocks_omap3.h>
+
+_TEXT_BASE:
+ .word TEXT_BASE /* sdram load addr from config.mk */
+
+#if !defined(CONFIG_SYS_NAND_BOOT) && !defined(CONFIG_SYS_NAND_BOOT)
+/**************************************************************************
+ * cpy_clk_code: relocates clock code into SRAM where its safer to execute
+ * R1 = SRAM destination address.
+ *************************************************************************/
+.global cpy_clk_code
+ cpy_clk_code:
+ /* Copy DPLL code into SRAM */
+ adr r0, go_to_speed /* get addr of clock setting code */
+ mov r2, #384 /* r2 size to copy (div by 32 bytes) */
+ mov r1, r1 /* r1 <- dest address (passed in) */
+ add r2, r2, r0 /* r2 <- source end address */
+next2:
+ ldmia r0!, {r3 - r10} /* copy from source address [r0] */
+ stmia r1!, {r3 - r10} /* copy to target address [r1] */
+ cmp r0, r2 /* until source end address [r2] */
+ bne next2
+ mov pc, lr /* back to caller */
+
+/* ***************************************************************************
+ * go_to_speed: -Moves to bypass, -Commits clock dividers, -puts dpll at speed
+ * -executed from SRAM.
+ * R0 = CM_CLKEN_PLL-bypass value
+ * R1 = CM_CLKSEL1_PLL-m, n, and divider values
+ * R2 = CM_CLKSEL_CORE-divider values
+ * R3 = CM_IDLEST_CKGEN - addr dpll lock wait
+ *
+ * Note: If core unlocks/relocks and SDRAM is running fast already it gets
+ * confused. A reset of the controller gets it back. Taking away its
+ * L3 when its not in self refresh seems bad for it. Normally, this
+ * code runs from flash before SDR is init so that should be ok.
+ ****************************************************************************/
+.global go_to_speed
+ go_to_speed:
+ stmfd sp!, {r4 - r6}
+
+ /* move into fast relock bypass */
+ ldr r4, pll_ctl_add
+ str r0, [r4]
+wait1:
+ ldr r5, [r3] /* get status */
+ and r5, r5, #0x1 /* isolate core status */
+ cmp r5, #0x1 /* still locked? */
+ beq wait1 /* if lock, loop */
+
+ /* set new dpll dividers _after_ in bypass */
+ ldr r5, pll_div_add1
+ str r1, [r5] /* set m, n, m2 */
+ ldr r5, pll_div_add2
+ str r2, [r5] /* set l3/l4/.. dividers*/
+ ldr r5, pll_div_add3 /* wkup */
+ ldr r2, pll_div_val3 /* rsm val */
+ str r2, [r5]
+ ldr r5, pll_div_add4 /* gfx */
+ ldr r2, pll_div_val4
+ str r2, [r5]
+ ldr r5, pll_div_add5 /* emu */
+ ldr r2, pll_div_val5
+ str r2, [r5]
+
+ /* now prepare GPMC (flash) for new dpll speed */
+ /* flash needs to be stable when we jump back to it */
+ ldr r5, flash_cfg3_addr
+ ldr r2, flash_cfg3_val
+ str r2, [r5]
+ ldr r5, flash_cfg4_addr
+ ldr r2, flash_cfg4_val
+ str r2, [r5]
+ ldr r5, flash_cfg5_addr
+ ldr r2, flash_cfg5_val
+ str r2, [r5]
+ ldr r5, flash_cfg1_addr
+ ldr r2, [r5]
+ orr r2, r2, #0x3 /* up gpmc divider */
+ str r2, [r5]
+
+ /* lock DPLL3 and wait a bit */
+ orr r0, r0, #0x7 /* set up for lock mode */
+ str r0, [r4] /* lock */
+ nop /* ARM slow at this point working at sys_clk */
+ nop
+ nop
+ nop
+wait2:
+ ldr r5, [r3] /* get status */
+ and r5, r5, #0x1 /* isolate core status */
+ cmp r5, #0x1 /* still locked? */
+ bne wait2 /* if lock, loop */
+ nop
+ nop
+ nop
+ nop
+ ldmfd sp!, {r4 - r6}
+ mov pc, lr /* back to caller, locked */
+
+_go_to_speed: .word go_to_speed
+
+/* these constants need to be close for PIC code */
+/* The Nor has to be in the Flash Base CS0 for this condition to happen */
+flash_cfg1_addr:
+ .word (GPMC_CONFIG_CS0 + GPMC_CONFIG1)
+flash_cfg3_addr:
+ .word (GPMC_CONFIG_CS0 + GPMC_CONFIG3)
+flash_cfg3_val:
+ .word STNOR_GPMC_CONFIG3
+flash_cfg4_addr:
+ .word (GPMC_CONFIG_CS0 + GPMC_CONFIG4)
+flash_cfg4_val:
+ .word STNOR_GPMC_CONFIG4
+flash_cfg5_val:
+ .word STNOR_GPMC_CONFIG5
+flash_cfg5_addr:
+ .word (GPMC_CONFIG_CS0 + GPMC_CONFIG5)
+pll_ctl_add:
+ .word CM_CLKEN_PLL
+pll_div_add1:
+ .word CM_CLKSEL1_PLL
+pll_div_add2:
+ .word CM_CLKSEL_CORE
+pll_div_add3:
+ .word CM_CLKSEL_WKUP
+pll_div_val3:
+ .word (WKUP_RSM << 1)
+pll_div_add4:
+ .word CM_CLKSEL_GFX
+pll_div_val4:
+ .word (GFX_DIV << 0)
+pll_div_add5:
+ .word CM_CLKSEL1_EMU
+pll_div_val5:
+ .word CLSEL1_EMU_VAL
+
+#endif
+
+.globl lowlevel_init
+lowlevel_init:
+ ldr sp, SRAM_STACK
+ str ip, [sp] /* stash old link register */
+ mov ip, lr /* save link reg across call */
+ bl s_init /* go setup pll, mux, memory */
+ ldr ip, [sp] /* restore save ip */
+ mov lr, ip /* restore link reg */
+
+ /* back to arch calling code */
+ mov pc, lr
+
+ /* the literal pools origin */
+ .ltorg
+
+REG_CONTROL_STATUS:
+ .word CONTROL_STATUS
+SRAM_STACK:
+ .word LOW_LEVEL_SRAM_STACK
+
+/* DPLL(1-4) PARAM TABLES */
+
+/*
+ * Each of the tables has M, N, FREQSEL, M2 values defined for nominal
+ * OPP (1.2V). The fields are defined according to dpll_param struct (clock.c).
+ * The values are defined for all possible sysclk and for ES1 and ES2.
+ */
+
+mpu_dpll_param:
+/* 12MHz */
+/* ES1 */
+.word MPU_M_12_ES1, MPU_N_12_ES1, MPU_FSEL_12_ES1, MPU_M2_12_ES1
+/* ES2 */
+.word MPU_M_12_ES2, MPU_N_12_ES2, MPU_FSEL_12_ES2, MPU_M2_ES2
+/* 3410 */
+.word MPU_M_12, MPU_N_12, MPU_FSEL_12, MPU_M2_12
+
+/* 13MHz */
+/* ES1 */
+.word MPU_M_13_ES1, MPU_N_13_ES1, MPU_FSEL_13_ES1, MPU_M2_13_ES1
+/* ES2 */
+.word MPU_M_13_ES2, MPU_N_13_ES2, MPU_FSEL_13_ES2, MPU_M2_13_ES2
+/* 3410 */
+.word MPU_M_13, MPU_N_13, MPU_FSEL_13, MPU_M2_13
+
+/* 19.2MHz */
+/* ES1 */
+.word MPU_M_19P2_ES1, MPU_N_19P2_ES1, MPU_FSEL_19P2_ES1, MPU_M2_19P2_ES1
+/* ES2 */
+.word MPU_M_19P2_ES2, MPU_N_19P2_ES2, MPU_FSEL_19P2_ES2, MPU_M2_19P2_ES2
+/* 3410 */
+.word MPU_M_19P2, MPU_N_19P2, MPU_FSEL_19P2, MPU_M2_19P2
+
+/* 26MHz */
+/* ES1 */
+.word MPU_M_26_ES1, MPU_N_26_ES1, MPU_FSEL_26_ES1, MPU_M2_26_ES1
+/* ES2 */
+.word MPU_M_26_ES2, MPU_N_26_ES2, MPU_FSEL_26_ES2, MPU_M2_26_ES2
+/* 3410 */
+.word MPU_M_26, MPU_N_26, MPU_FSEL_26, MPU_M2_26
+
+/* 38.4MHz */
+/* ES1 */
+.word MPU_M_38P4_ES1, MPU_N_38P4_ES1, MPU_FSEL_38P4_ES1, MPU_M2_38P4_ES1
+/* ES2 */
+.word MPU_M_38P4_ES2, MPU_N_38P4_ES2, MPU_FSEL_38P4_ES2, MPU_M2_38P4_ES2
+/* 3410 */
+.word MPU_M_38P4, MPU_N_38P4, MPU_FSEL_38P4, MPU_M2_38P4
+
+
+.globl get_mpu_dpll_param
+get_mpu_dpll_param:
+ adr r0, mpu_dpll_param
+ mov pc, lr
+
+iva_dpll_param:
+/* 12MHz */
+/* ES1 */
+.word IVA_M_12_ES1, IVA_N_12_ES1, IVA_FSEL_12_ES1, IVA_M2_12_ES1
+/* ES2 */
+.word IVA_M_12_ES2, IVA_N_12_ES2, IVA_FSEL_12_ES2, IVA_M2_12_ES2
+/* 3410 */
+.word IVA_M_12, IVA_N_12, IVA_FSEL_12, IVA_M2_12
+
+/* 13MHz */
+/* ES1 */
+.word IVA_M_13_ES1, IVA_N_13_ES1, IVA_FSEL_13_ES1, IVA_M2_13_ES1
+/* ES2 */
+.word IVA_M_13_ES2, IVA_N_13_ES2, IVA_FSEL_13_ES2, IVA_M2_13_ES2
+/* 3410 */
+.word IVA_M_13, IVA_N_13, IVA_FSEL_13, IVA_M2_13
+
+/* 19.2MHz */
+/* ES1 */
+.word IVA_M_19P2_ES1, IVA_N_19P2_ES1, IVA_FSEL_19P2_ES1, IVA_M2_19P2_ES1
+/* ES2 */
+.word IVA_M_19P2_ES2, IVA_N_19P2_ES2, IVA_FSEL_19P2_ES2, IVA_M2_19P2_ES2
+/* 3410 */
+.word IVA_M_19P2, IVA_N_19P2, IVA_FSEL_19P2, IVA_M2_19P2
+
+/* 26MHz */
+/* ES1 */
+.word IVA_M_26_ES1, IVA_N_26_ES1, IVA_FSEL_26_ES1, IVA_M2_26_ES1
+/* ES2 */
+.word IVA_M_26_ES2, IVA_N_26_ES2, IVA_FSEL_26_ES2, IVA_M2_26_ES2
+/* 3410 */
+.word IVA_M_26, IVA_N_26, IVA_FSEL_26, IVA_M2_26
+
+/* 38.4MHz */
+/* ES1 */
+.word IVA_M_38P4_ES1, IVA_N_38P4_ES1, IVA_FSEL_38P4_ES1, IVA_M2_38P4_ES1
+/* ES2 */
+.word IVA_M_38P4_ES2, IVA_N_38P4_ES2, IVA_FSEL_38P4_ES2, IVA_M2_38P4_ES2
+/* 3410 */
+.word IVA_M_38P4, IVA_N_38P4, IVA_FSEL_38P4, IVA_M2_38P4
+
+
+.globl get_iva_dpll_param
+get_iva_dpll_param:
+ adr r0, iva_dpll_param
+ mov pc, lr
+
+/* Core DPLL targets for L3 at 166 & L133 */
+core_dpll_param:
+/* 12MHz */
+/* ES1 */
+.word CORE_M_12_ES1, CORE_N_12_ES1, CORE_FSL_12_ES1, CORE_M2_12_ES1
+/* ES2 */
+.word CORE_M_12, CORE_N_12, CORE_FSEL_12, CORE_M2_12
+/* 3410 */
+.word CORE_M_12, CORE_N_12, CORE_FSEL_12, CORE_M2_12
+
+/* 13MHz */
+/* ES1 */
+.word CORE_M_13_ES1, CORE_N_13_ES1, CORE_FSL_13_ES1, CORE_M2_13_ES1
+/* ES2 */
+.word CORE_M_13, CORE_N_13, CORE_FSEL_13, CORE_M2_13
+/* 3410 */
+.word CORE_M_13, CORE_N_13, CORE_FSEL_13, CORE_M2_13
+
+/* 19.2MHz */
+/* ES1 */
+.word CORE_M_19P2_ES1, CORE_N_19P2_ES1, CORE_FSL_19P2_ES1, CORE_M2_19P2_ES1
+/* ES2 */
+.word CORE_M_19P2, CORE_N_19P2, CORE_FSEL_19P2, CORE_M2_19P2
+/* 3410 */
+.word CORE_M_19P2, CORE_N_19P2, CORE_FSEL_19P2, CORE_M2_19P2
+
+/* 26MHz */
+/* ES1 */
+.word CORE_M_26_ES1, CORE_N_26_ES1, CORE_FSL_26_ES1, CORE_M2_26_ES1
+/* ES2 */
+.word CORE_M_26, CORE_N_26, CORE_FSEL_26, CORE_M2_26
+/* 3410 */
+.word CORE_M_26, CORE_N_26, CORE_FSEL_26, CORE_M2_26
+
+/* 38.4MHz */
+/* ES1 */
+.word CORE_M_38P4_ES1, CORE_N_38P4_ES1, CORE_FSL_38P4_ES1, CORE_M2_38P4_ES1
+/* ES2 */
+.word CORE_M_38P4, CORE_N_38P4, CORE_FSEL_38P4, CORE_M2_38P4
+/* 3410 */
+.word CORE_M_38P4, CORE_N_38P4, CORE_FSEL_38P4, CORE_M2_38P4
+
+.globl get_core_dpll_param
+get_core_dpll_param:
+ adr r0, core_dpll_param
+ mov pc, lr
+
+/* PER DPLL values are same for both ES1 and ES2 */
+per_dpll_param:
+/* 12MHz */
+.word PER_M_12, PER_N_12, PER_FSEL_12, PER_M2_12
+
+/* 13MHz */
+.word PER_M_13, PER_N_13, PER_FSEL_13, PER_M2_13
+
+/* 19.2MHz */
+.word PER_M_19P2, PER_N_19P2, PER_FSEL_19P2, PER_M2_19P2
+
+/* 26MHz */
+.word PER_M_26, PER_N_26, PER_FSEL_26, PER_M2_26
+
+/* 38.4MHz */
+.word PER_M_38P4, PER_N_38P4, PER_FSEL_38P4, PER_M2_38P4
+
+.globl get_per_dpll_param
+get_per_dpll_param:
+ adr r0, per_dpll_param
+ mov pc, lr
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ * Manikandan Pillai <mani.pillai@ti.com>
+ *
+ * Initial Code from:
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/sys_proto.h>
+#include <command.h>
+
+/*
+ * Only One NAND allowed on board at a time.
+ * The GPMC CS Base for the same
+ */
+unsigned int boot_flash_base;
+unsigned int boot_flash_off;
+unsigned int boot_flash_sec;
+unsigned int boot_flash_type;
+volatile unsigned int boot_flash_env_addr;
+
+#if defined(CONFIG_CMD_NAND)
+static u32 gpmc_m_nand[GPMC_MAX_REG] = {
+ M_NAND_GPMC_CONFIG1,
+ M_NAND_GPMC_CONFIG2,
+ M_NAND_GPMC_CONFIG3,
+ M_NAND_GPMC_CONFIG4,
+ M_NAND_GPMC_CONFIG5,
+ M_NAND_GPMC_CONFIG6, 0
+};
+
+gpmc_csx_t *nand_cs_base;
+gpmc_t *gpmc_cfg_base;
+
+#if defined(CONFIG_ENV_IS_IN_NAND)
+#define GPMC_CS 0
+#else
+#define GPMC_CS 1
+#endif
+
+#endif
+
+#if defined(CONFIG_CMD_ONENAND)
+static u32 gpmc_onenand[GPMC_MAX_REG] = {
+ ONENAND_GPMC_CONFIG1,
+ ONENAND_GPMC_CONFIG2,
+ ONENAND_GPMC_CONFIG3,
+ ONENAND_GPMC_CONFIG4,
+ ONENAND_GPMC_CONFIG5,
+ ONENAND_GPMC_CONFIG6, 0
+};
+
+gpmc_csx_t *onenand_cs_base;
+
+#if defined(CONFIG_ENV_IS_IN_ONENAND)
+#define GPMC_CS 0
+#else
+#define GPMC_CS 1
+#endif
+
+#endif
+
+static sdrc_t *sdrc_base = (sdrc_t *)OMAP34XX_SDRC_BASE;
+
+/**************************************************************************
+ * make_cs1_contiguous() - for es2 and above remap cs1 behind cs0 to allow
+ * command line mem=xyz use all memory with out discontinuous support
+ * compiled in. Could do it at the ATAG, but there really is two banks...
+ * Called as part of 2nd phase DDR init.
+ **************************************************************************/
+void make_cs1_contiguous(void)
+{
+ u32 size, a_add_low, a_add_high;
+
+ size = get_sdr_cs_size(CS0);
+ size /= SZ_32M; /* find size to offset CS1 */
+ a_add_high = (size & 3) << 8; /* set up low field */
+ a_add_low = (size & 0x3C) >> 2; /* set up high field */
+ writel((a_add_high | a_add_low), &sdrc_base->cs_cfg);
+
+}
+
+/********************************************************
+ * mem_ok() - test used to see if timings are correct
+ * for a part. Helps in guessing which part
+ * we are currently using.
+ *******************************************************/
+u32 mem_ok(u32 cs)
+{
+ u32 val1, val2, addr;
+ u32 pattern = 0x12345678;
+
+ addr = OMAP34XX_SDRC_CS0 + get_sdr_cs_offset(cs);
+
+ writel(0x0, addr + 0x400); /* clear pos A */
+ writel(pattern, addr); /* pattern to pos B */
+ writel(0x0, addr + 4); /* remove pattern off the bus */
+ val1 = readl(addr + 0x400); /* get pos A value */
+ val2 = readl(addr); /* get val2 */
+
+ if ((val1 != 0) || (val2 != pattern)) /* see if pos A val changed */
+ return 0;
+ else
+ return 1;
+}
+
+/********************************************************
+ * sdrc_init() - init the sdrc chip selects CS0 and CS1
+ * - early init routines, called from flash or
+ * SRAM.
+ *******************************************************/
+void sdrc_init(void)
+{
+ /* only init up first bank here */
+ do_sdrc_init(CS0, EARLY_INIT);
+}
+
+/*************************************************************************
+ * do_sdrc_init(): initialize the SDRAM for use.
+ * -code sets up SDRAM basic SDRC timings for CS0
+ * -optimal settings can be placed here, or redone after i2c
+ * inspection of board info
+ *
+ * - code called once in C-Stack only context for CS0 and a possible 2nd
+ * time depending on memory configuration from stack+global context
+ **************************************************************************/
+
+void do_sdrc_init(u32 cs, u32 early)
+{
+ sdrc_actim_t *sdrc_actim_base;
+
+ if(cs)
+ sdrc_actim_base = (sdrc_actim_t *)SDRC_ACTIM_CTRL1_BASE;
+ else
+ sdrc_actim_base = (sdrc_actim_t *)SDRC_ACTIM_CTRL0_BASE;
+
+ if (early) {
+ /* reset sdrc controller */
+ writel(SOFTRESET, &sdrc_base->sysconfig);
+ wait_on_value(RESETDONE, RESETDONE, &sdrc_base->status,
+ 12000000);
+ writel(0, &sdrc_base->sysconfig);
+
+ /* setup sdrc to ball mux */
+ writel(SDP_SDRC_SHARING, &sdrc_base->sharing);
+
+ /* Disable Power Down of CKE cuz of 1 CKE on combo part */
+ writel(SRFRONRESET | PAGEPOLICY_HIGH, &sdrc_base->power);
+
+ writel(ENADLL | DLLPHASE_90, &sdrc_base->dlla_ctrl);
+ sdelay(0x20000);
+ }
+
+ writel(RASWIDTH_13BITS | CASWIDTH_10BITS | ADDRMUXLEGACY |
+ RAMSIZE_128 | BANKALLOCATION | B32NOT16 | B32NOT16 |
+ DEEPPD | DDR_SDRAM, &sdrc_base->cs[cs].mcfg);
+ writel(ARCV | ARE_ARCV_1, &sdrc_base->cs[cs].rfr_ctrl);
+ writel(V_ACTIMA_165, &sdrc_actim_base->ctrla);
+ writel(V_ACTIMB_165, &sdrc_actim_base->ctrlb);
+
+ writel(CMD_NOP, &sdrc_base ->cs[cs].manual);
+ writel(CMD_PRECHARGE, &sdrc_base->cs[cs].manual);
+ writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
+ writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
+
+ /*
+ * CAS latency 3, Write Burst = Read Burst, Serial Mode,
+ * Burst length = 4
+ */
+ writel(CASL3 | BURSTLENGTH4, &sdrc_base->cs[cs].mr);
+
+ if (!mem_ok(cs))
+ writel(0, &sdrc_base->cs[cs].mcfg);
+}
+
+void enable_gpmc_config(u32 *gpmc_config, gpmc_csx_t *gpmc_cs_base, u32 base,
+ u32 size)
+{
+ writel(0, &gpmc_cs_base->config7);
+ sdelay(1000);
+ /* Delay for settling */
+ writel(gpmc_config[0], &gpmc_cs_base->config1);
+ writel(gpmc_config[1], &gpmc_cs_base->config2);
+ writel(gpmc_config[2], &gpmc_cs_base->config3);
+ writel(gpmc_config[3], &gpmc_cs_base->config4);
+ writel(gpmc_config[4], &gpmc_cs_base->config5);
+ writel(gpmc_config[5], &gpmc_cs_base->config6);
+ /* Enable the config */
+ writel((((size & 0xF) << 8) | ((base >> 24) & 0x3F) |
+ (1 << 6)), &gpmc_cs_base->config7);
+ sdelay(2000);
+}
+
+/*****************************************************
+ * gpmc_init(): init gpmc bus
+ * Init GPMC for x16, MuxMode (SDRAM in x32).
+ * This code can only be executed from SRAM or SDRAM.
+ *****************************************************/
+void gpmc_init(void)
+{
+ /* putting a blanket check on GPMC based on ZeBu for now */
+ u32 *gpmc_config = NULL;
+ gpmc_t *gpmc_base = (gpmc_t *)GPMC_BASE;
+ gpmc_csx_t *gpmc_cs_base = (gpmc_csx_t *)GPMC_CONFIG_CS0_BASE;
+ u32 base = 0;
+ u32 size = 0;
+ u32 f_off = CONFIG_SYS_MONITOR_LEN;
+ u32 f_sec = 0;
+ u32 config = 0;
+
+ /* global settings */
+ writel(0, &gpmc_base->irqenable); /* isr's sources masked */
+ writel(0, &gpmc_base->timeout_control);/* timeout disable */
+
+ config = readl(&gpmc_base->config);
+ config &= (~0xf00);
+ writel(config, &gpmc_base->config);
+
+ /*
+ * Disable the GPMC0 config set by ROM code
+ * It conflicts with our MPDB (both at 0x08000000)
+ */
+ writel(0, &gpmc_cs_base->config7);
+ sdelay(1000);
+
+#if defined(CONFIG_CMD_NAND) /* CS 0 */
+ gpmc_config = gpmc_m_nand;
+ gpmc_cfg_base = gpmc_base;
+ nand_cs_base = (gpmc_csx_t *)(GPMC_CONFIG_CS0_BASE +
+ (GPMC_CS * GPMC_CONFIG_WIDTH));
+ base = PISMO1_NAND_BASE;
+ size = PISMO1_NAND_SIZE;
+ enable_gpmc_config(gpmc_config, nand_cs_base, base, size);
+#if defined(CONFIG_ENV_IS_IN_NAND)
+ f_off = SMNAND_ENV_OFFSET;
+ f_sec = SZ_128K;
+ /* env setup */
+ boot_flash_base = base;
+ boot_flash_off = f_off;
+ boot_flash_sec = f_sec;
+ boot_flash_env_addr = f_off;
+#endif
+#endif
+
+#if defined(CONFIG_CMD_ONENAND)
+ gpmc_config = gpmc_onenand;
+ onenand_cs_base = (gpmc_csx_t *)(GPMC_CONFIG_CS0_BASE +
+ (GPMC_CS * GPMC_CONFIG_WIDTH));
+ base = PISMO1_ONEN_BASE;
+ size = PISMO1_ONEN_SIZE;
+ enable_gpmc_config(gpmc_config, onenand_cs_base, base, size);
+#if defined(CONFIG_ENV_IS_IN_ONENAND)
+ f_off = ONENAND_ENV_OFFSET;
+ f_sec = SZ_128K;
+ /* env setup */
+ boot_flash_base = base;
+ boot_flash_off = f_off;
+ boot_flash_sec = f_sec;
+ boot_flash_env_addr = f_off;
+#endif
+#endif
+}
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ * Manikandan Pillai <mani.pillai@ti.com>
+ *
+ * Derived from Beagle Board and 3430 SDP code by
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/mem.h> /* get mem tables */
+#include <asm/arch/sys_proto.h>
+#include <i2c.h>
+
+extern omap3_sysinfo sysinfo;
+static gpmc_csx_t *gpmc_cs_base = (gpmc_csx_t *)GPMC_CONFIG_CS0_BASE;
+static sdrc_t *sdrc_base = (sdrc_t *)OMAP34XX_SDRC_BASE;
+static ctrl_t *ctrl_base = (ctrl_t *)OMAP34XX_CTRL_BASE;
+
+/******************************************
+ * get_cpu_rev(void) - extract version info
+ ******************************************/
+u32 get_cpu_rev(void)
+{
+ u32 cpuid = 0;
+
+ /*
+ * On ES1.0 the IDCODE register is not exposed on L4
+ * so using CPU ID to differentiate
+ * between ES2.0 and ES1.0.
+ */
+ __asm__ __volatile__("mrc p15, 0, %0, c0, c0, 0":"=r"(cpuid));
+ if ((cpuid & 0xf) == 0x0)
+ return CPU_3430_ES1;
+ else
+ return CPU_3430_ES2;
+
+}
+
+/****************************************************
+ * is_mem_sdr() - return 1 if mem type in use is SDR
+ ****************************************************/
+u32 is_mem_sdr(void)
+{
+ if (readl(&sdrc_base->cs[CS0].mr) == SDP_SDRC_MR_0_SDR)
+ return 1;
+ return 0;
+}
+
+/***********************************************************************
+ * get_cs0_size() - get size of chip select 0/1
+ ************************************************************************/
+u32 get_sdr_cs_size(u32 cs)
+{
+ u32 size;
+
+ /* get ram size field */
+ size = readl(&sdrc_base->cs[cs].mcfg) >> 8;
+ size &= 0x3FF; /* remove unwanted bits */
+ size *= SZ_2M; /* find size in MB */
+ return size;
+}
+
+/***********************************************************************
+ * get_sdr_cs_offset() - get offset of cs from cs0 start
+ ************************************************************************/
+u32 get_sdr_cs_offset(u32 cs)
+{
+ u32 offset;
+
+ if (!cs)
+ return 0;
+
+ offset = readl(&sdrc_base->cs_cfg);
+ offset = (offset & 15) << 27 | (offset & 0x30) >> 17;
+
+ return offset;
+}
+
+/***********************************************************************
+ * get_board_type() - get board type based on current production stats.
+ * - NOTE-1-: 2 I2C EEPROMs will someday be populated with proper info.
+ * when they are available we can get info from there. This should
+ * be correct of all known boards up until today.
+ * - NOTE-2- EEPROMs are populated but they are updated very slowly. To
+ * avoid waiting on them we will use ES version of the chip to get info.
+ * A later version of the FPGA migth solve their speed issue.
+ ************************************************************************/
+u32 get_board_type(void)
+{
+ if (get_cpu_rev() == CPU_3430_ES2)
+ return sysinfo.board_type_v2;
+ else
+ return sysinfo.board_type_v1;
+}
+
+/***************************************************************************
+ * get_gpmc0_base() - Return current address hardware will be
+ * fetching from. The below effectively gives what is correct, its a bit
+ * mis-leading compared to the TRM. For the most general case the mask
+ * needs to be also taken into account this does work in practice.
+ * - for u-boot we currently map:
+ * -- 0 to nothing,
+ * -- 4 to flash
+ * -- 8 to enent
+ * -- c to wifi
+ ****************************************************************************/
+u32 get_gpmc0_base(void)
+{
+ u32 b;
+
+ b = readl(&gpmc_cs_base->config7);
+ b &= 0x1F; /* keep base [5:0] */
+ b = b << 24; /* ret 0x0b000000 */
+ return b;
+}
+
+/*******************************************************************
+ * get_gpmc0_width() - See if bus is in x8 or x16 (mainly for nand)
+ *******************************************************************/
+u32 get_gpmc0_width(void)
+{
+ return WIDTH_16BIT;
+}
+
+/*************************************************************************
+ * get_board_rev() - setup to pass kernel board revision information
+ * returns:(bit[0-3] sub version, higher bit[7-4] is higher version)
+ *************************************************************************/
+u32 get_board_rev(void)
+{
+ return 0x20;
+}
+
+/*********************************************************************
+ * display_board_info() - print banner with board info.
+ *********************************************************************/
+void display_board_info(u32 btype)
+{
+ char *mem_s, *sec_s;
+
+ if (is_mem_sdr())
+ mem_s = "mSDR";
+ else
+ mem_s = "LPDDR";
+
+ switch (get_device_type()) {
+ case TST_DEVICE:
+ sec_s = "TST";
+ break;
+ case EMU_DEVICE:
+ sec_s = "EMU";
+ break;
+ case HS_DEVICE:
+ sec_s = "HS";
+ break;
+ case GP_DEVICE:
+ sec_s = "GP";
+ break;
+ default:
+ sec_s = "?";
+ }
+
+ printf("OMAP%s-%s rev %d, CPU-OPP2 L3-165MHz\n", sysinfo.cpu_string,
+ sec_s, get_cpu_rev());
+ printf("%s + %s/%s\n", sysinfo.board_string,
+ mem_s, sysinfo.nand_string);
+
+}
+
+/********************************************************
+ * get_base(); get upper addr of current execution
+ *******************************************************/
+u32 get_base(void)
+{
+ u32 val;
+
+ __asm__ __volatile__("mov %0, pc \n":"=r"(val)::"memory");
+ val &= 0xF0000000;
+ val >>= 28;
+ return val;
+}
+
+/********************************************************
+ * is_running_in_flash() - tell if currently running in
+ * FLASH.
+ *******************************************************/
+u32 is_running_in_flash(void)
+{
+ if (get_base() < 4)
+ return 1; /* in FLASH */
+
+ return 0; /* running in SRAM or SDRAM */
+}
+
+/********************************************************
+ * is_running_in_sram() - tell if currently running in
+ * SRAM.
+ *******************************************************/
+u32 is_running_in_sram(void)
+{
+ if (get_base() == 4)
+ return 1; /* in SRAM */
+
+ return 0; /* running in FLASH or SDRAM */
+}
+
+/********************************************************
+ * is_running_in_sdram() - tell if currently running in
+ * SDRAM.
+ *******************************************************/
+u32 is_running_in_sdram(void)
+{
+ if (get_base() > 4)
+ return 1; /* in SDRAM */
+
+ return 0; /* running in SRAM or FLASH */
+}
+
+/***************************************************************
+ * get_boot_type() - Is this an XIP type device or a stream one
+ * bits 4-0 specify type. Bit 5 says mem/perif
+ ***************************************************************/
+u32 get_boot_type(void)
+{
+ return (readl(&ctrl_base->status) & SYSBOOT_MASK);
+}
+
+/*************************************************************
+ * get_device_type(): tell if GP/HS/EMU/TST
+ *************************************************************/
+u32 get_device_type(void)
+{
+ return ((readl(&ctrl_base->status) & (DEVICE_MASK)) >> 8);
+}
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/clocks.h>
+#include <asm/arch/sys_proto.h>
+
+/************************************************************
+ * sdelay() - simple spin loop. Will be constant time as
+ * its generally used in bypass conditions only. This
+ * is necessary until timers are accessible.
+ *
+ * not inline to increase chances its in cache when called
+ *************************************************************/
+void sdelay(unsigned long loops)
+{
+ __asm__ volatile ("1:\n" "subs %0, %1, #1\n"
+ "bne 1b":"=r" (loops):"0"(loops));
+}
+
+/*****************************************************************
+ * sr32 - clear & set a value in a bit range for a 32 bit address
+ *****************************************************************/
+void sr32(void *addr, u32 start_bit, u32 num_bits, u32 value)
+{
+ u32 tmp, msk = 0;
+ msk = 1 << num_bits;
+ --msk;
+ tmp = readl((u32)addr) & ~(msk << start_bit);
+ tmp |= value << start_bit;
+ writel(tmp, (u32)addr);
+}
+
+/*********************************************************************
+ * wait_on_value() - common routine to allow waiting for changes in
+ * volatile regs.
+ *********************************************************************/
+u32 wait_on_value(u32 read_bit_mask, u32 match_value, void *read_addr,
+ u32 bound)
+{
+ u32 i = 0, val;
+ do {
+ ++i;
+ val = readl((u32)read_addr) & read_bit_mask;
+ if (val == match_value)
+ return 1;
+ if (i == bound)
+ return 0;
+ } while (1);
+}
--- /dev/null
+/*
+ * armboot - Startup Code for OMAP3530/ARM Cortex CPU-core
+ *
+ * Copyright (c) 2004 Texas Instruments <r-woodruff2@ti.com>
+ *
+ * Copyright (c) 2001 Marius Gröger <mag@sysgo.de>
+ * Copyright (c) 2002 Alex Züpke <azu@sysgo.de>
+ * Copyright (c) 2002 Gary Jennejohn <gj@denx.de>
+ * Copyright (c) 2003 Richard Woodruff <r-woodruff2@ti.com>
+ * Copyright (c) 2003 Kshitij <kshitij@ti.com>
+ * Copyright (c) 2006-2008 Syed Mohammed Khasim <x0khasim@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+.globl _start
+_start: b reset
+ ldr pc, _undefined_instruction
+ ldr pc, _software_interrupt
+ ldr pc, _prefetch_abort
+ ldr pc, _data_abort
+ ldr pc, _not_used
+ ldr pc, _irq
+ ldr pc, _fiq
+
+_undefined_instruction: .word undefined_instruction
+_software_interrupt: .word software_interrupt
+_prefetch_abort: .word prefetch_abort
+_data_abort: .word data_abort
+_not_used: .word not_used
+_irq: .word irq
+_fiq: .word fiq
+_pad: .word 0x12345678 /* now 16*4=64 */
+.global _end_vect
+_end_vect:
+
+ .balignl 16,0xdeadbeef
+/*************************************************************************
+ *
+ * Startup Code (reset vector)
+ *
+ * do important init only if we don't start from memory!
+ * setup Memory and board specific bits prior to relocation.
+ * relocate armboot to ram
+ * setup stack
+ *
+ *************************************************************************/
+
+_TEXT_BASE:
+ .word TEXT_BASE
+
+.globl _armboot_start
+_armboot_start:
+ .word _start
+
+/*
+ * These are defined in the board-specific linker script.
+ */
+.globl _bss_start
+_bss_start:
+ .word __bss_start
+
+.globl _bss_end
+_bss_end:
+ .word _end
+
+#ifdef CONFIG_USE_IRQ
+/* IRQ stack memory (calculated at run-time) */
+.globl IRQ_STACK_START
+IRQ_STACK_START:
+ .word 0x0badc0de
+
+/* IRQ stack memory (calculated at run-time) */
+.globl FIQ_STACK_START
+FIQ_STACK_START:
+ .word 0x0badc0de
+#endif
+
+/*
+ * the actual reset code
+ */
+
+reset:
+ /*
+ * set the cpu to SVC32 mode
+ */
+ mrs r0, cpsr
+ bic r0, r0, #0x1f
+ orr r0, r0, #0xd3
+ msr cpsr,r0
+
+#if (CONFIG_OMAP34XX)
+ /* Copy vectors to mask ROM indirect addr */
+ adr r0, _start @ r0 <- current position of code
+ add r0, r0, #4 @ skip reset vector
+ mov r2, #64 @ r2 <- size to copy
+ add r2, r0, r2 @ r2 <- source end address
+ mov r1, #SRAM_OFFSET0 @ build vect addr
+ mov r3, #SRAM_OFFSET1
+ add r1, r1, r3
+ mov r3, #SRAM_OFFSET2
+ add r1, r1, r3
+next:
+ ldmia r0!, {r3 - r10} @ copy from source address [r0]
+ stmia r1!, {r3 - r10} @ copy to target address [r1]
+ cmp r0, r2 @ until source end address [r2]
+ bne next @ loop until equal */
+#if !defined(CONFIG_SYS_NAND_BOOT) && !defined(CONFIG_SYS_ONENAND_BOOT)
+ /* No need to copy/exec the clock code - DPLL adjust already done
+ * in NAND/oneNAND Boot.
+ */
+ bl cpy_clk_code @ put dpll adjust code behind vectors
+#endif /* NAND Boot */
+#endif
+ /* the mask ROM code should have PLL and others stable */
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
+ bl cpu_init_crit
+#endif
+
+#ifndef CONFIG_SKIP_RELOCATE_UBOOT
+relocate: @ relocate U-Boot to RAM
+ adr r0, _start @ r0 <- current position of code
+ ldr r1, _TEXT_BASE @ test if we run from flash or RAM
+ cmp r0, r1 @ don't reloc during debug
+ beq stack_setup
+
+ ldr r2, _armboot_start
+ ldr r3, _bss_start
+ sub r2, r3, r2 @ r2 <- size of armboot
+ add r2, r0, r2 @ r2 <- source end address
+
+copy_loop: @ copy 32 bytes at a time
+ ldmia r0!, {r3 - r10} @ copy from source address [r0]
+ stmia r1!, {r3 - r10} @ copy to target address [r1]
+ cmp r0, r2 @ until source end addreee [r2]
+ ble copy_loop
+#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
+
+ /* Set up the stack */
+stack_setup:
+ ldr r0, _TEXT_BASE @ upper 128 KiB: relocated uboot
+ sub r0, r0, #CONFIG_SYS_MALLOC_LEN @ malloc area
+ sub r0, r0, #CONFIG_SYS_GBL_DATA_SIZE @ bdinfo
+#ifdef CONFIG_USE_IRQ
+ sub r0, r0, #(CONFIG_STACKSIZE_IRQ + CONFIG_STACKSIZE_FIQ)
+#endif
+ sub sp, r0, #12 @ leave 3 words for abort-stack
+ and sp, sp, #~7 @ 8 byte alinged for (ldr/str)d
+
+ /* Clear BSS (if any). Is below tx (watch load addr - need space) */
+clear_bss:
+ ldr r0, _bss_start @ find start of bss segment
+ ldr r1, _bss_end @ stop here
+ mov r2, #0x00000000 @ clear value
+clbss_l:
+ str r2, [r0] @ clear BSS location
+ cmp r0, r1 @ are we at the end yet
+ add r0, r0, #4 @ increment clear index pointer
+ bne clbss_l @ keep clearing till at end
+
+ ldr pc, _start_armboot @ jump to C code
+
+_start_armboot: .word start_armboot
+
+
+/*************************************************************************
+ *
+ * CPU_init_critical registers
+ *
+ * setup important registers
+ * setup memory timing
+ *
+ *************************************************************************/
+cpu_init_crit:
+ /*
+ * Invalidate L1 I/D
+ */
+ mov r0, #0 @ set up for MCR
+ mcr p15, 0, r0, c8, c7, 0 @ invalidate TLBs
+ mcr p15, 0, r0, c7, c5, 0 @ invalidate icache
+
+ /*
+ * disable MMU stuff and caches
+ */
+ mrc p15, 0, r0, c1, c0, 0
+ bic r0, r0, #0x00002000 @ clear bits 13 (--V-)
+ bic r0, r0, #0x00000007 @ clear bits 2:0 (-CAM)
+ orr r0, r0, #0x00000002 @ set bit 1 (--A-) Align
+ orr r0, r0, #0x00000800 @ set bit 12 (Z---) BTB
+ mcr p15, 0, r0, c1, c0, 0
+
+ /*
+ * Jump to board specific initialization...
+ * The Mask ROM will have already initialized
+ * basic memory. Go here to bump up clock rate and handle
+ * wake up conditions.
+ */
+ mov ip, lr @ persevere link reg across call
+ bl lowlevel_init @ go setup pll,mux,memory
+ mov lr, ip @ restore link
+ mov pc, lr @ back to my caller
+/*
+ *************************************************************************
+ *
+ * Interrupt handling
+ *
+ *************************************************************************
+ */
+@
+@ IRQ stack frame.
+@
+#define S_FRAME_SIZE 72
+
+#define S_OLD_R0 68
+#define S_PSR 64
+#define S_PC 60
+#define S_LR 56
+#define S_SP 52
+
+#define S_IP 48
+#define S_FP 44
+#define S_R10 40
+#define S_R9 36
+#define S_R8 32
+#define S_R7 28
+#define S_R6 24
+#define S_R5 20
+#define S_R4 16
+#define S_R3 12
+#define S_R2 8
+#define S_R1 4
+#define S_R0 0
+
+#define MODE_SVC 0x13
+#define I_BIT 0x80
+
+/*
+ * use bad_save_user_regs for abort/prefetch/undef/swi ...
+ * use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling
+ */
+
+ .macro bad_save_user_regs
+ sub sp, sp, #S_FRAME_SIZE @ carve out a frame on current
+ @ user stack
+ stmia sp, {r0 - r12} @ Save user registers (now in
+ @ svc mode) r0-r12
+
+ ldr r2, _armboot_start
+ sub r2, r2, #(CONFIG_SYS_MALLOC_LEN)
+ sub r2, r2, #(CONFIG_SYS_GBL_DATA_SIZE + 8) @ set base 2 words into abort
+ @ stack
+ ldmia r2, {r2 - r3} @ get values for "aborted" pc
+ @ and cpsr (into parm regs)
+ add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack
+
+ add r5, sp, #S_SP
+ mov r1, lr
+ stmia r5, {r0 - r3} @ save sp_SVC, lr_SVC, pc, cpsr
+ mov r0, sp @ save current stack into r0
+ @ (param register)
+ .endm
+
+ .macro irq_save_user_regs
+ sub sp, sp, #S_FRAME_SIZE
+ stmia sp, {r0 - r12} @ Calling r0-r12
+ add r8, sp, #S_PC @ !! R8 NEEDS to be saved !!
+ @ a reserved stack spot would
+ @ be good.
+ stmdb r8, {sp, lr}^ @ Calling SP, LR
+ str lr, [r8, #0] @ Save calling PC
+ mrs r6, spsr
+ str r6, [r8, #4] @ Save CPSR
+ str r0, [r8, #8] @ Save OLD_R0
+ mov r0, sp
+ .endm
+
+ .macro irq_restore_user_regs
+ ldmia sp, {r0 - lr}^ @ Calling r0 - lr
+ mov r0, r0
+ ldr lr, [sp, #S_PC] @ Get PC
+ add sp, sp, #S_FRAME_SIZE
+ subs pc, lr, #4 @ return & move spsr_svc into
+ @ cpsr
+ .endm
+
+ .macro get_bad_stack
+ ldr r13, _armboot_start @ setup our mode stack (enter
+ @ in banked mode)
+ sub r13, r13, #(CONFIG_SYS_MALLOC_LEN) @ move past malloc pool
+ sub r13, r13, #(CONFIG_SYS_GBL_DATA_SIZE + 8) @ move to reserved a couple
+ @ spots for abort stack
+
+ str lr, [r13] @ save caller lr in position 0
+ @ of saved stack
+ mrs lr, spsr @ get the spsr
+ str lr, [r13, #4] @ save spsr in position 1 of
+ @ saved stack
+
+ mov r13, #MODE_SVC @ prepare SVC-Mode
+ @ msr spsr_c, r13
+ msr spsr, r13 @ switch modes, make sure
+ @ moves will execute
+ mov lr, pc @ capture return pc
+ movs pc, lr @ jump to next instruction &
+ @ switch modes.
+ .endm
+
+ .macro get_bad_stack_swi
+ sub r13, r13, #4 @ space on current stack for
+ @ scratch reg.
+ str r0, [r13] @ save R0's value.
+ ldr r0, _armboot_start @ get data regions start
+ sub r0, r0, #(CONFIG_SYS_MALLOC_LEN) @ move past malloc pool
+ sub r0, r0, #(CONFIG_SYS_GBL_DATA_SIZE + 8) @ move past gbl and a couple
+ @ spots for abort stack
+ str lr, [r0] @ save caller lr in position 0
+ @ of saved stack
+ mrs r0, spsr @ get the spsr
+ str lr, [r0, #4] @ save spsr in position 1 of
+ @ saved stack
+ ldr r0, [r13] @ restore r0
+ add r13, r13, #4 @ pop stack entry
+ .endm
+
+ .macro get_irq_stack @ setup IRQ stack
+ ldr sp, IRQ_STACK_START
+ .endm
+
+ .macro get_fiq_stack @ setup FIQ stack
+ ldr sp, FIQ_STACK_START
+ .endm
+
+/*
+ * exception handlers
+ */
+ .align 5
+undefined_instruction:
+ get_bad_stack
+ bad_save_user_regs
+ bl do_undefined_instruction
+
+ .align 5
+software_interrupt:
+ get_bad_stack_swi
+ bad_save_user_regs
+ bl do_software_interrupt
+
+ .align 5
+prefetch_abort:
+ get_bad_stack
+ bad_save_user_regs
+ bl do_prefetch_abort
+
+ .align 5
+data_abort:
+ get_bad_stack
+ bad_save_user_regs
+ bl do_data_abort
+
+ .align 5
+not_used:
+ get_bad_stack
+ bad_save_user_regs
+ bl do_not_used
+
+#ifdef CONFIG_USE_IRQ
+
+ .align 5
+irq:
+ get_irq_stack
+ irq_save_user_regs
+ bl do_irq
+ irq_restore_user_regs
+
+ .align 5
+fiq:
+ get_fiq_stack
+ /* someone ought to write a more effective fiq_save_user_regs */
+ irq_save_user_regs
+ bl do_fiq
+ irq_restore_user_regs
+
+#else
+
+ .align 5
+irq:
+ get_bad_stack
+ bad_save_user_regs
+ bl do_irq
+
+ .align 5
+fiq:
+ get_bad_stack
+ bad_save_user_regs
+ bl do_fiq
+
+#endif
+
+/*
+ * v7_flush_dcache_all()
+ *
+ * Flush the whole D-cache.
+ *
+ * Corrupted registers: r0-r5, r7, r9-r11
+ *
+ * - mm - mm_struct describing address space
+ */
+ .align 5
+.global v7_flush_dcache_all
+v7_flush_dcache_all:
+ stmfd r13!, {r0 - r5, r7, r9 - r12, r14}
+
+ mov r7, r0 @ take a backup of device type
+ cmp r0, #0x3 @ check if the device type is
+ @ GP
+ moveq r12, #0x1 @ set up to invalide L2
+smi: .word 0x01600070 @ Call SMI monitor (smieq)
+ cmp r7, #0x3 @ compare again in case its
+ @ lost
+ beq finished_inval @ if GP device, inval done
+ @ above
+
+ mrc p15, 1, r0, c0, c0, 1 @ read clidr
+ ands r3, r0, #0x7000000 @ extract loc from clidr
+ mov r3, r3, lsr #23 @ left align loc bit field
+ beq finished_inval @ if loc is 0, then no need to
+ @ clean
+ mov r10, #0 @ start clean at cache level 0
+inval_loop1:
+ add r2, r10, r10, lsr #1 @ work out 3x current cache
+ @ level
+ mov r1, r0, lsr r2 @ extract cache type bits from
+ @ clidr
+ and r1, r1, #7 @ mask of the bits for current
+ @ cache only
+ cmp r1, #2 @ see what cache we have at
+ @ this level
+ blt skip_inval @ skip if no cache, or just
+ @ i-cache
+ mcr p15, 2, r10, c0, c0, 0 @ select current cache level
+ @ in cssr
+ mov r2, #0 @ operand for mcr SBZ
+ mcr p15, 0, r2, c7, c5, 4 @ flush prefetch buffer to
+ @ sych the new cssr&csidr,
+ @ with armv7 this is 'isb',
+ @ but we compile with armv5
+ mrc p15, 1, r1, c0, c0, 0 @ read the new csidr
+ and r2, r1, #7 @ extract the length of the
+ @ cache lines
+ add r2, r2, #4 @ add 4 (line length offset)
+ ldr r4, =0x3ff
+ ands r4, r4, r1, lsr #3 @ find maximum number on the
+ @ way size
+ clz r5, r4 @ find bit position of way
+ @ size increment
+ ldr r7, =0x7fff
+ ands r7, r7, r1, lsr #13 @ extract max number of the
+ @ index size
+inval_loop2:
+ mov r9, r4 @ create working copy of max
+ @ way size
+inval_loop3:
+ orr r11, r10, r9, lsl r5 @ factor way and cache number
+ @ into r11
+ orr r11, r11, r7, lsl r2 @ factor index number into r11
+ mcr p15, 0, r11, c7, c6, 2 @ invalidate by set/way
+ subs r9, r9, #1 @ decrement the way
+ bge inval_loop3
+ subs r7, r7, #1 @ decrement the index
+ bge inval_loop2
+skip_inval:
+ add r10, r10, #2 @ increment cache number
+ cmp r3, r10
+ bgt inval_loop1
+finished_inval:
+ mov r10, #0 @ swith back to cache level 0
+ mcr p15, 2, r10, c0, c0, 0 @ select current cache level
+ @ in cssr
+ mcr p15, 0, r10, c7, c5, 4 @ flush prefetch buffer,
+ @ with armv7 this is 'isb',
+ @ but we compile with armv5
+
+ ldmfd r13!, {r0 - r5, r7, r9 - r12, pc}
+
+
+ .align 5
+.global reset_cpu
+reset_cpu:
+ ldr r1, rstctl @ get addr for global reset
+ @ reg
+ mov r3, #0x2 @ full reset pll + mpu
+ str r3, [r1] @ force reset
+ mov r0, r0
+_loop_forever:
+ b _loop_forever
+rstctl:
+ .word PRM_RSTCTRL
--- /dev/null
+
+The Nomadik 8815 CPU has a "secure" boot mode where no external access
+(not even JTAG) is allowed. The "remap" bits in the evaluation board
+are configured in order to boot from the internal ROM memory (in
+secure mode).
+
+The boot process as defined by the manufacturer executes external code
+(loaded from NAND or OneNAND) that that disables such "security" in
+order to run u-boot and later the kernel without constraints. Such
+code is a proprietary initial boot loader, called "X-Loader" (in case
+anyone wonders, it has no relations with other loaders with the same
+name and there is no GPL code inside the ST X-Loader).
+
+SDRAM configuration, PLL setup and initial loading from NAND is
+implemented in the X-Loader, so U-Boot is already running in SDRAM
+when control is handed over to it.
+
+
+On www.st.com/nomadik and on www.stnwireless.com there are documents,
+summary data and white papers on Nomadik. The full datasheet for
+STn8815 is not currently available on line but under specific request
+to the local ST sales offices.
--- /dev/null
+
+Summary
+=======
+
+This README is about U-Boot support for TI's ARM Cortex-A8 based OMAP3 [1]
+family of SoCs. TI's OMAP3 SoC family contains an ARM Cortex-A8. Additionally,
+some family members contain a TMS320C64x+ DSP and/or an Imagination SGX 2D/3D
+graphics processor and various other standard peripherals.
+
+Currently the following boards are supported:
+
+* OMAP3530 BeagleBoard [2]
+
+* Gumstix Overo [3]
+
+* TI EVM [4]
+
+* OpenPandora Ltd. Pandora [5]
+
+* TI/Logic PD Zoom MDK [6]
+
+Toolchain
+=========
+
+While ARM Cortex-A8 support ARM v7 instruction set (-march=armv7a) we compile
+with -march=armv5 to allow more compilers to work. For U-Boot code this has
+no performance impact.
+
+Build
+=====
+
+* BeagleBoard:
+
+make omap3_beagle_config
+make
+
+* Gumstix Overo:
+
+make omap3_overo_config
+make
+
+* TI EVM:
+
+make omap3_evm_config
+make
+
+* Pandora:
+
+make omap3_pandora_config
+make
+
+* Zoom MDK:
+
+make omap3_zoom1_config
+make
+
+Custom commands
+===============
+
+To make U-Boot for OMAP3 support NAND device SW or HW ECC calculation, U-Boot
+for OMAP3 supports custom user command
+
+nandecc hw/sw
+
+To be compatible with NAND drivers using SW ECC (e.g. kernel code)
+
+nandecc sw
+
+enables SW ECC calculation. HW ECC enabled with
+
+nandecc hw
+
+is typically used to write 2nd stage bootloader (known as 'x-loader') which is
+executed by OMAP3's boot rom and therefore has to be written with HW ECC.
+
+For all other commands see
+
+help
+
+Acknowledgements
+================
+
+OMAP3 U-Boot is based on U-Boot tar ball [7] for BeagleBoard and EVM done by
+several TI employees.
+
+Links
+=====
+
+[1] OMAP3:
+
+http://www.ti.com/omap3 (high volume) and
+http://www.ti.com/omap35x (broad market)
+
+[2] OMAP3530 BeagleBoard:
+
+http://beagleboard.org/
+
+[3] Gumstix Overo:
+
+http://www.gumstix.net/Overo/
+
+[4] TI EVM:
+
+http://focus.ti.com/docs/toolsw/folders/print/tmdxevm3503.html
+
+[5] OpenPandora Ltd. Pandora:
+
+http://openpandora.org/
+
+[6] TI/Logic PD Zoom MDK:
+
+http://www.logicpd.com/products/devkit/ti/zoom_mobile_development_kit
+
+[7] TI OMAP3 U-Boot:
+
+http://beagleboard.googlecode.com/files/u-boot_beagle_revb.tar.gz
COBJS-$(CONFIG_I2C_MXC) += mxc_i2c.o
COBJS-$(CONFIG_DRIVER_OMAP1510_I2C) += omap1510_i2c.o
COBJS-$(CONFIG_DRIVER_OMAP24XX_I2C) += omap24xx_i2c.o
+COBJS-$(CONFIG_DRIVER_OMAP34XX_I2C) += omap24xx_i2c.o
COBJS-$(CONFIG_SOFT_I2C) += soft_i2c.o
COBJS-$(CONFIG_TSI108_I2C) += tsi108_i2c.o
status = wait_for_pin ();
if (status & I2C_STAT_RRDY) {
+#if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX)
+ *value = readb (I2C_DATA);
+#else
*value = readw (I2C_DATA);
+#endif
udelay (20000);
} else {
i2c_error = 1;
status = wait_for_pin ();
if (status & I2C_STAT_XRDY) {
+#if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX)
+ /* send out 1 byte */
+ writeb (regoffset, I2C_DATA);
+ writew (I2C_STAT_XRDY, I2C_STAT);
+
+ status = wait_for_pin ();
+ if ((status & I2C_STAT_XRDY)) {
+ /* send out next 1 byte */
+ writeb (value, I2C_DATA);
+ writew (I2C_STAT_XRDY, I2C_STAT);
+ } else {
+ i2c_error = 1;
+ }
+#else
/* send out two bytes */
writew ((value << 8) + regoffset, I2C_DATA);
+#endif
/* must have enough delay to allow BB bit to go low */
udelay (50000);
if (readw (I2C_STAT) & I2C_STAT_NACK) {
while(1){
stat = readw(I2C_STAT);
if(stat == I2C_STAT_RRDY){
+#if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX)
+ readb(I2C_DATA);
+#else
readw(I2C_DATA);
+#endif
writew(I2C_STAT_RRDY,I2C_STAT);
udelay(1000);
}else
LIB := $(obj)libmmc.a
COBJS-$(CONFIG_ATMEL_MCI) += atmel_mci.o
+COBJS-$(CONFIG_OMAP3_MMC) += omap3_mmc.o
COBJS := $(COBJS-y)
SRCS := $(COBJS:.o=.c)
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Texas Instruments, <www.ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation's version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <common.h>
+#include <fat.h>
+#include <mmc.h>
+#include <part.h>
+#include <i2c.h>
+
+const unsigned short mmc_transspeed_val[15][4] = {
+ {CLKD(10, 1), CLKD(10, 10), CLKD(10, 100), CLKD(10, 1000)},
+ {CLKD(12, 1), CLKD(12, 10), CLKD(12, 100), CLKD(12, 1000)},
+ {CLKD(13, 1), CLKD(13, 10), CLKD(13, 100), CLKD(13, 1000)},
+ {CLKD(15, 1), CLKD(15, 10), CLKD(15, 100), CLKD(15, 1000)},
+ {CLKD(20, 1), CLKD(20, 10), CLKD(20, 100), CLKD(20, 1000)},
+ {CLKD(26, 1), CLKD(26, 10), CLKD(26, 100), CLKD(26, 1000)},
+ {CLKD(30, 1), CLKD(30, 10), CLKD(30, 100), CLKD(30, 1000)},
+ {CLKD(35, 1), CLKD(35, 10), CLKD(35, 100), CLKD(35, 1000)},
+ {CLKD(40, 1), CLKD(40, 10), CLKD(40, 100), CLKD(40, 1000)},
+ {CLKD(45, 1), CLKD(45, 10), CLKD(45, 100), CLKD(45, 1000)},
+ {CLKD(52, 1), CLKD(52, 10), CLKD(52, 100), CLKD(52, 1000)},
+ {CLKD(55, 1), CLKD(55, 10), CLKD(55, 100), CLKD(55, 1000)},
+ {CLKD(60, 1), CLKD(60, 10), CLKD(60, 100), CLKD(60, 1000)},
+ {CLKD(70, 1), CLKD(70, 10), CLKD(70, 100), CLKD(70, 1000)},
+ {CLKD(80, 1), CLKD(80, 10), CLKD(80, 100), CLKD(80, 1000)}
+};
+
+mmc_card_data cur_card_data;
+static block_dev_desc_t mmc_blk_dev;
+
+block_dev_desc_t *mmc_get_dev(int dev)
+{
+ return (block_dev_desc_t *) &mmc_blk_dev;
+}
+
+void twl4030_mmc_config(void)
+{
+ unsigned char data;
+
+ data = 0x20;
+ i2c_write(0x4B, 0x82, 1, &data, 1);
+ data = 0x2;
+ i2c_write(0x4B, 0x85, 1, &data, 1);
+}
+
+unsigned char mmc_board_init(void)
+{
+ unsigned int value = 0;
+
+ twl4030_mmc_config();
+
+ value = CONTROL_PBIAS_LITE;
+ CONTROL_PBIAS_LITE = value | (1 << 2) | (1 << 1) | (1 << 9);
+
+ value = CONTROL_DEV_CONF0;
+ CONTROL_DEV_CONF0 = value | (1 << 24);
+
+ return 1;
+}
+
+void mmc_init_stream(void)
+{
+ volatile unsigned int mmc_stat;
+
+ OMAP_HSMMC_CON |= INIT_INITSTREAM;
+
+ OMAP_HSMMC_CMD = MMC_CMD0;
+ do {
+ mmc_stat = OMAP_HSMMC_STAT;
+ } while (!(mmc_stat & CC_MASK));
+
+ OMAP_HSMMC_STAT = CC_MASK;
+
+ OMAP_HSMMC_CMD = MMC_CMD0;
+ do {
+ mmc_stat = OMAP_HSMMC_STAT;
+ } while (!(mmc_stat & CC_MASK));
+
+ OMAP_HSMMC_STAT = OMAP_HSMMC_STAT;
+ OMAP_HSMMC_CON &= ~INIT_INITSTREAM;
+}
+
+unsigned char mmc_clock_config(unsigned int iclk, unsigned short clk_div)
+{
+ unsigned int val;
+
+ mmc_reg_out(OMAP_HSMMC_SYSCTL, (ICE_MASK | DTO_MASK | CEN_MASK),
+ (ICE_STOP | DTO_15THDTO | CEN_DISABLE));
+
+ switch (iclk) {
+ case CLK_INITSEQ:
+ val = MMC_INIT_SEQ_CLK / 2;
+ break;
+ case CLK_400KHZ:
+ val = MMC_400kHz_CLK;
+ break;
+ case CLK_MISC:
+ val = clk_div;
+ break;
+ default:
+ return 0;
+ }
+ mmc_reg_out(OMAP_HSMMC_SYSCTL,
+ ICE_MASK | CLKD_MASK, (val << CLKD_OFFSET) | ICE_OSCILLATE);
+
+ while ((OMAP_HSMMC_SYSCTL & ICS_MASK) == ICS_NOTREADY) ;
+
+ OMAP_HSMMC_SYSCTL |= CEN_ENABLE;
+ return 1;
+}
+
+unsigned char mmc_init_setup(void)
+{
+ unsigned int reg_val;
+
+ mmc_board_init();
+
+ OMAP_HSMMC_SYSCONFIG |= MMC_SOFTRESET;
+ while ((OMAP_HSMMC_SYSSTATUS & RESETDONE) == 0) ;
+
+ OMAP_HSMMC_SYSCTL |= SOFTRESETALL;
+ while ((OMAP_HSMMC_SYSCTL & SOFTRESETALL) != 0x0) ;
+
+ OMAP_HSMMC_HCTL = DTW_1_BITMODE | SDBP_PWROFF | SDVS_3V0;
+ OMAP_HSMMC_CAPA |= VS30_3V0SUP | VS18_1V8SUP;
+
+ reg_val = OMAP_HSMMC_CON & RESERVED_MASK;
+
+ OMAP_HSMMC_CON = CTPL_MMC_SD | reg_val | WPP_ACTIVEHIGH |
+ CDP_ACTIVEHIGH | MIT_CTO | DW8_1_4BITMODE | MODE_FUNC |
+ STR_BLOCK | HR_NOHOSTRESP | INIT_NOINIT | NOOPENDRAIN;
+
+ mmc_clock_config(CLK_INITSEQ, 0);
+ OMAP_HSMMC_HCTL |= SDBP_PWRON;
+
+ OMAP_HSMMC_IE = 0x307f0033;
+
+ mmc_init_stream();
+ return 1;
+}
+
+unsigned char mmc_send_cmd(unsigned int cmd, unsigned int arg,
+ unsigned int *response)
+{
+ volatile unsigned int mmc_stat;
+
+ while ((OMAP_HSMMC_PSTATE & DATI_MASK) == DATI_CMDDIS) ;
+
+ OMAP_HSMMC_BLK = BLEN_512BYTESLEN | NBLK_STPCNT;
+ OMAP_HSMMC_STAT = 0xFFFFFFFF;
+ OMAP_HSMMC_ARG = arg;
+ OMAP_HSMMC_CMD = cmd | CMD_TYPE_NORMAL | CICE_NOCHECK |
+ CCCE_NOCHECK | MSBS_SGLEBLK | ACEN_DISABLE | BCE_DISABLE |
+ DE_DISABLE;
+
+ while (1) {
+ do {
+ mmc_stat = OMAP_HSMMC_STAT;
+ } while (mmc_stat == 0);
+
+ if ((mmc_stat & ERRI_MASK) != 0)
+ return (unsigned char) mmc_stat;
+
+ if (mmc_stat & CC_MASK) {
+ OMAP_HSMMC_STAT = CC_MASK;
+ response[0] = OMAP_HSMMC_RSP10;
+ if ((cmd & RSP_TYPE_MASK) == RSP_TYPE_LGHT136) {
+ response[1] = OMAP_HSMMC_RSP32;
+ response[2] = OMAP_HSMMC_RSP54;
+ response[3] = OMAP_HSMMC_RSP76;
+ }
+ break;
+ }
+ }
+ return 1;
+}
+
+unsigned char mmc_read_data(unsigned int *output_buf)
+{
+ volatile unsigned int mmc_stat;
+ unsigned int read_count = 0;
+
+ /*
+ * Start Polled Read
+ */
+ while (1) {
+ do {
+ mmc_stat = OMAP_HSMMC_STAT;
+ } while (mmc_stat == 0);
+
+ if ((mmc_stat & ERRI_MASK) != 0)
+ return (unsigned char) mmc_stat;
+
+ if (mmc_stat & BRR_MASK) {
+ unsigned int k;
+
+ OMAP_HSMMC_STAT |= BRR_MASK;
+ for (k = 0; k < MMCSD_SECTOR_SIZE / 4; k++) {
+ *output_buf = OMAP_HSMMC_DATA;
+ output_buf++;
+ read_count += 4;
+ }
+ }
+
+ if (mmc_stat & BWR_MASK)
+ OMAP_HSMMC_STAT |= BWR_MASK;
+
+ if (mmc_stat & TC_MASK) {
+ OMAP_HSMMC_STAT |= TC_MASK;
+ break;
+ }
+ }
+ return 1;
+}
+
+unsigned char mmc_detect_card(mmc_card_data *mmc_card_cur)
+{
+ unsigned char err;
+ unsigned int argument = 0;
+ unsigned int ocr_value, ocr_recvd, ret_cmd41, hcs_val;
+ unsigned int resp[4];
+ unsigned short retry_cnt = 2000;
+
+ /* Set to Initialization Clock */
+ err = mmc_clock_config(CLK_400KHZ, 0);
+ if (err != 1)
+ return err;
+
+ mmc_card_cur->RCA = MMC_RELATIVE_CARD_ADDRESS;
+ argument = 0x00000000;
+
+ ocr_value = (0x1FF << 15);
+ err = mmc_send_cmd(MMC_CMD0, argument, resp);
+ if (err != 1)
+ return err;
+
+ argument = SD_CMD8_CHECK_PATTERN | SD_CMD8_2_7_3_6_V_RANGE;
+ err = mmc_send_cmd(MMC_SDCMD8, argument, resp);
+ hcs_val = (err == 1) ?
+ MMC_OCR_REG_HOST_CAPACITY_SUPPORT_SECTOR :
+ MMC_OCR_REG_HOST_CAPACITY_SUPPORT_BYTE;
+
+ argument = 0x0000 << 16;
+ err = mmc_send_cmd(MMC_CMD55, argument, resp);
+ if (err == 1) {
+ mmc_card_cur->card_type = SD_CARD;
+ ocr_value |= hcs_val;
+ ret_cmd41 = MMC_ACMD41;
+ } else {
+ mmc_card_cur->card_type = MMC_CARD;
+ ocr_value |= MMC_OCR_REG_ACCESS_MODE_SECTOR;
+ ret_cmd41 = MMC_CMD1;
+ OMAP_HSMMC_CON &= ~OD;
+ OMAP_HSMMC_CON |= OPENDRAIN;
+ }
+
+ argument = ocr_value;
+ err = mmc_send_cmd(ret_cmd41, argument, resp);
+ if (err != 1)
+ return err;
+
+ ocr_recvd = ((mmc_resp_r3 *) resp)->ocr;
+
+ while (!(ocr_recvd & (0x1 << 31)) && (retry_cnt > 0)) {
+ retry_cnt--;
+ if (mmc_card_cur->card_type == SD_CARD) {
+ argument = 0x0000 << 16;
+ err = mmc_send_cmd(MMC_CMD55, argument, resp);
+ }
+
+ argument = ocr_value;
+ err = mmc_send_cmd(ret_cmd41, argument, resp);
+ if (err != 1)
+ return err;
+ ocr_recvd = ((mmc_resp_r3 *) resp)->ocr;
+ }
+
+ if (!(ocr_recvd & (0x1 << 31)))
+ return 0;
+
+ if (mmc_card_cur->card_type == MMC_CARD) {
+ if ((ocr_recvd & MMC_OCR_REG_ACCESS_MODE_MASK) ==
+ MMC_OCR_REG_ACCESS_MODE_SECTOR) {
+ mmc_card_cur->mode = SECTOR_MODE;
+ } else {
+ mmc_card_cur->mode = BYTE_MODE;
+ }
+
+ ocr_recvd &= ~MMC_OCR_REG_ACCESS_MODE_MASK;
+ } else {
+ if ((ocr_recvd & MMC_OCR_REG_HOST_CAPACITY_SUPPORT_MASK)
+ == MMC_OCR_REG_HOST_CAPACITY_SUPPORT_SECTOR) {
+ mmc_card_cur->mode = SECTOR_MODE;
+ } else {
+ mmc_card_cur->mode = BYTE_MODE;
+ }
+ ocr_recvd &= ~MMC_OCR_REG_HOST_CAPACITY_SUPPORT_MASK;
+ }
+
+ ocr_recvd &= ~(0x1 << 31);
+ if (!(ocr_recvd & ocr_value))
+ return 0;
+
+ err = mmc_send_cmd(MMC_CMD2, argument, resp);
+ if (err != 1)
+ return err;
+
+ if (mmc_card_cur->card_type == MMC_CARD) {
+ argument = mmc_card_cur->RCA << 16;
+ err = mmc_send_cmd(MMC_CMD3, argument, resp);
+ if (err != 1)
+ return err;
+ } else {
+ argument = 0x00000000;
+ err = mmc_send_cmd(MMC_SDCMD3, argument, resp);
+ if (err != 1)
+ return err;
+
+ mmc_card_cur->RCA = ((mmc_resp_r6 *) resp)->newpublishedrca;
+ }
+
+ OMAP_HSMMC_CON &= ~OD;
+ OMAP_HSMMC_CON |= NOOPENDRAIN;
+ return 1;
+}
+
+unsigned char mmc_read_cardsize(mmc_card_data *mmc_dev_data,
+ mmc_csd_reg_t *cur_csd)
+{
+ mmc_extended_csd_reg_t ext_csd;
+ unsigned int size, count, blk_len, blk_no, card_size, argument;
+ unsigned char err;
+ unsigned int resp[4];
+
+ if (mmc_dev_data->mode == SECTOR_MODE) {
+ if (mmc_dev_data->card_type == SD_CARD) {
+ card_size =
+ (((mmc_sd2_csd_reg_t *) cur_csd)->
+ c_size_lsb & MMC_SD2_CSD_C_SIZE_LSB_MASK) |
+ ((((mmc_sd2_csd_reg_t *) cur_csd)->
+ c_size_msb & MMC_SD2_CSD_C_SIZE_MSB_MASK)
+ << MMC_SD2_CSD_C_SIZE_MSB_OFFSET);
+ mmc_dev_data->size = card_size * 1024;
+ if (mmc_dev_data->size == 0)
+ return 0;
+ } else {
+ argument = 0x00000000;
+ err = mmc_send_cmd(MMC_CMD8, argument, resp);
+ if (err != 1)
+ return err;
+ err = mmc_read_data((unsigned int *) &ext_csd);
+ if (err != 1)
+ return err;
+ mmc_dev_data->size = ext_csd.sectorcount;
+
+ if (mmc_dev_data->size == 0)
+ mmc_dev_data->size = 8388608;
+ }
+ } else {
+ if (cur_csd->c_size_mult >= 8)
+ return 0;
+
+ if (cur_csd->read_bl_len >= 12)
+ return 0;
+
+ /* Compute size */
+ count = 1 << (cur_csd->c_size_mult + 2);
+ card_size = (cur_csd->c_size_lsb & MMC_CSD_C_SIZE_LSB_MASK) |
+ ((cur_csd->c_size_msb & MMC_CSD_C_SIZE_MSB_MASK)
+ << MMC_CSD_C_SIZE_MSB_OFFSET);
+ blk_no = (card_size + 1) * count;
+ blk_len = 1 << cur_csd->read_bl_len;
+ size = blk_no * blk_len;
+ mmc_dev_data->size = size / MMCSD_SECTOR_SIZE;
+ if (mmc_dev_data->size == 0)
+ return 0;
+ }
+ return 1;
+}
+
+unsigned char omap_mmc_read_sect(unsigned int start_sec, unsigned int num_bytes,
+ mmc_card_data *mmc_c,
+ unsigned long *output_buf)
+{
+ unsigned char err;
+ unsigned int argument;
+ unsigned int resp[4];
+ unsigned int num_sec_val =
+ (num_bytes + (MMCSD_SECTOR_SIZE - 1)) / MMCSD_SECTOR_SIZE;
+ unsigned int sec_inc_val;
+
+ if (num_sec_val == 0)
+ return 1;
+
+ if (mmc_c->mode == SECTOR_MODE) {
+ argument = start_sec;
+ sec_inc_val = 1;
+ } else {
+ argument = start_sec * MMCSD_SECTOR_SIZE;
+ sec_inc_val = MMCSD_SECTOR_SIZE;
+ }
+
+ while (num_sec_val) {
+ err = mmc_send_cmd(MMC_CMD17, argument, resp);
+ if (err != 1)
+ return err;
+
+ err = mmc_read_data((unsigned int *) output_buf);
+ if (err != 1)
+ return err;
+
+ output_buf += (MMCSD_SECTOR_SIZE / 4);
+ argument += sec_inc_val;
+ num_sec_val--;
+ }
+ return 1;
+}
+
+unsigned char configure_mmc(mmc_card_data *mmc_card_cur)
+{
+ unsigned char ret_val;
+ unsigned int argument;
+ unsigned int resp[4];
+ unsigned int trans_clk, trans_fact, trans_unit, retries = 2;
+ mmc_csd_reg_t Card_CSD;
+ unsigned char trans_speed;
+
+ ret_val = mmc_init_setup();
+
+ if (ret_val != 1)
+ return ret_val;
+
+ do {
+ ret_val = mmc_detect_card(mmc_card_cur);
+ retries--;
+ } while ((retries > 0) && (ret_val != 1));
+
+ argument = mmc_card_cur->RCA << 16;
+ ret_val = mmc_send_cmd(MMC_CMD9, argument, resp);
+ if (ret_val != 1)
+ return ret_val;
+
+ ((unsigned int *) &Card_CSD)[3] = resp[3];
+ ((unsigned int *) &Card_CSD)[2] = resp[2];
+ ((unsigned int *) &Card_CSD)[1] = resp[1];
+ ((unsigned int *) &Card_CSD)[0] = resp[0];
+
+ if (mmc_card_cur->card_type == MMC_CARD)
+ mmc_card_cur->version = Card_CSD.spec_vers;
+
+ trans_speed = Card_CSD.tran_speed;
+
+ ret_val = mmc_send_cmd(MMC_CMD4, MMC_DSR_DEFAULT << 16, resp);
+ if (ret_val != 1)
+ return ret_val;
+
+ trans_unit = trans_speed & MMC_CSD_TRAN_SPEED_UNIT_MASK;
+ trans_fact = trans_speed & MMC_CSD_TRAN_SPEED_FACTOR_MASK;
+
+ if (trans_unit > MMC_CSD_TRAN_SPEED_UNIT_100MHZ)
+ return 0;
+
+ if ((trans_fact < MMC_CSD_TRAN_SPEED_FACTOR_1_0) ||
+ (trans_fact > MMC_CSD_TRAN_SPEED_FACTOR_8_0))
+ return 0;
+
+ trans_unit >>= 0;
+ trans_fact >>= 3;
+
+ trans_clk = mmc_transspeed_val[trans_fact - 1][trans_unit] * 2;
+ ret_val = mmc_clock_config(CLK_MISC, trans_clk);
+
+ if (ret_val != 1)
+ return ret_val;
+
+ argument = mmc_card_cur->RCA << 16;
+ ret_val = mmc_send_cmd(MMC_CMD7_SELECT, argument, resp);
+ if (ret_val != 1)
+ return ret_val;
+
+ /* Configure the block length to 512 bytes */
+ argument = MMCSD_SECTOR_SIZE;
+ ret_val = mmc_send_cmd(MMC_CMD16, argument, resp);
+ if (ret_val != 1)
+ return ret_val;
+
+ /* get the card size in sectors */
+ ret_val = mmc_read_cardsize(mmc_card_cur, &Card_CSD);
+ if (ret_val != 1)
+ return ret_val;
+
+ return 1;
+}
+unsigned long mmc_bread(int dev_num, unsigned long blknr, lbaint_t blkcnt,
+ void *dst)
+{
+ omap_mmc_read_sect(blknr, (blkcnt * MMCSD_SECTOR_SIZE), &cur_card_data,
+ (unsigned long *) dst);
+ return 1;
+}
+
+int mmc_init(int verbose)
+{
+ if (configure_mmc(&cur_card_data) != 1)
+ return 1;
+
+ mmc_blk_dev.if_type = IF_TYPE_MMC;
+ mmc_blk_dev.part_type = PART_TYPE_DOS;
+ mmc_blk_dev.dev = 0;
+ mmc_blk_dev.lun = 0;
+ mmc_blk_dev.type = 0;
+
+ /* FIXME fill in the correct size (is set to 32MByte) */
+ mmc_blk_dev.blksz = MMCSD_SECTOR_SIZE;
+ mmc_blk_dev.lba = 0x10000;
+ mmc_blk_dev.removable = 0;
+ mmc_blk_dev.block_read = mmc_bread;
+
+ fat_register_device(&mmc_blk_dev, 1);
+ return 0;
+}
+
+int mmc_read(ulong src, uchar *dst, int size)
+{
+ return 0;
+}
+
+int mmc_write(uchar *src, ulong dst, int size)
+{
+ return 0;
+}
+
+int mmc2info(ulong addr)
+{
+ return 0;
+}
COBJS-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_nand.o
COBJS-$(CONFIG_NAND_FSL_UPM) += fsl_upm.o
COBJS-$(CONFIG_NAND_S3C64XX) += s3c64xx.o
+COBJS-$(CONFIG_NAND_OMAP_GPMC) += omap_gpmc.o
endif
COBJS := $(COBJS-y)
--- /dev/null
+/*
+ * (C) Copyright 2004-2008 Texas Instruments, <www.ti.com>
+ * Rohit Choraria <rohitkc@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/omap_gpmc.h>
+#include <linux/mtd/nand_ecc.h>
+#include <nand.h>
+
+static uint8_t cs;
+static gpmc_t *gpmc_base = (gpmc_t *)GPMC_BASE;
+static gpmc_csx_t *gpmc_cs_base;
+static struct nand_ecclayout hw_nand_oob = GPMC_NAND_HW_ECC_LAYOUT;
+
+/*
+ * omap_nand_hwcontrol - Set the address pointers corretly for the
+ * following address/data/command operation
+ */
+static void omap_nand_hwcontrol(struct mtd_info *mtd, int32_t cmd,
+ uint32_t ctrl)
+{
+ register struct nand_chip *this = mtd->priv;
+
+ /*
+ * Point the IO_ADDR to DATA and ADDRESS registers instead
+ * of chip address
+ */
+ switch (ctrl) {
+ case NAND_CTRL_CHANGE | NAND_CTRL_CLE:
+ this->IO_ADDR_W = (void __iomem *)&gpmc_cs_base->nand_cmd;
+ break;
+ case NAND_CTRL_CHANGE | NAND_CTRL_ALE:
+ this->IO_ADDR_W = (void __iomem *)&gpmc_cs_base->nand_adr;
+ break;
+ case NAND_CTRL_CHANGE | NAND_NCE:
+ this->IO_ADDR_W = (void __iomem *)&gpmc_cs_base->nand_dat;
+ break;
+ }
+
+ if (cmd != NAND_CMD_NONE)
+ writeb(cmd, this->IO_ADDR_W);
+}
+
+/*
+ * omap_hwecc_init - Initialize the Hardware ECC for NAND flash in
+ * GPMC controller
+ * @mtd: MTD device structure
+ *
+ */
+static void omap_hwecc_init(struct nand_chip *chip)
+{
+ /*
+ * Init ECC Control Register
+ * Clear all ECC | Enable Reg1
+ */
+ writel(ECCCLEAR | ECCRESULTREG1, &gpmc_base->ecc_control);
+ writel(ECCSIZE1 | ECCSIZE0 | ECCSIZE0SEL, &gpmc_base->ecc_size_config);
+}
+
+/*
+ * gen_true_ecc - This function will generate true ECC value, which
+ * can be used when correcting data read from NAND flash memory core
+ *
+ * @ecc_buf: buffer to store ecc code
+ *
+ * @return: re-formatted ECC value
+ */
+static uint32_t gen_true_ecc(uint8_t *ecc_buf)
+{
+ return ecc_buf[0] | (ecc_buf[1] << 16) | ((ecc_buf[2] & 0xF0) << 20) |
+ ((ecc_buf[2] & 0x0F) << 8);
+}
+
+/*
+ * omap_correct_data - Compares the ecc read from nand spare area with ECC
+ * registers values and corrects one bit error if it has occured
+ * Further details can be had from OMAP TRM and the following selected links:
+ * http://en.wikipedia.org/wiki/Hamming_code
+ * http://www.cs.utexas.edu/users/plaxton/c/337/05f/slides/ErrorCorrection-4.pdf
+ *
+ * @mtd: MTD device structure
+ * @dat: page data
+ * @read_ecc: ecc read from nand flash
+ * @calc_ecc: ecc read from ECC registers
+ *
+ * @return 0 if data is OK or corrected, else returns -1
+ */
+static int omap_correct_data(struct mtd_info *mtd, uint8_t *dat,
+ uint8_t *read_ecc, uint8_t *calc_ecc)
+{
+ uint32_t orig_ecc, new_ecc, res, hm;
+ uint16_t parity_bits, byte;
+ uint8_t bit;
+
+ /* Regenerate the orginal ECC */
+ orig_ecc = gen_true_ecc(read_ecc);
+ new_ecc = gen_true_ecc(calc_ecc);
+ /* Get the XOR of real ecc */
+ res = orig_ecc ^ new_ecc;
+ if (res) {
+ /* Get the hamming width */
+ hm = hweight32(res);
+ /* Single bit errors can be corrected! */
+ if (hm == 12) {
+ /* Correctable data! */
+ parity_bits = res >> 16;
+ bit = (parity_bits & 0x7);
+ byte = (parity_bits >> 3) & 0x1FF;
+ /* Flip the bit to correct */
+ dat[byte] ^= (0x1 << bit);
+ } else if (hm == 1) {
+ printf("Error: Ecc is wrong\n");
+ /* ECC itself is corrupted */
+ return 2;
+ } else {
+ /*
+ * hm distance != parity pairs OR one, could mean 2 bit
+ * error OR potentially be on a blank page..
+ * orig_ecc: contains spare area data from nand flash.
+ * new_ecc: generated ecc while reading data area.
+ * Note: if the ecc = 0, all data bits from which it was
+ * generated are 0xFF.
+ * The 3 byte(24 bits) ecc is generated per 512byte
+ * chunk of a page. If orig_ecc(from spare area)
+ * is 0xFF && new_ecc(computed now from data area)=0x0,
+ * this means that data area is 0xFF and spare area is
+ * 0xFF. A sure sign of a erased page!
+ */
+ if ((orig_ecc == 0x0FFF0FFF) && (new_ecc == 0x00000000))
+ return 0;
+ printf("Error: Bad compare! failed\n");
+ /* detected 2 bit error */
+ return -1;
+ }
+ }
+ return 0;
+}
+
+/*
+ * omap_calculate_ecc - Generate non-inverted ECC bytes.
+ *
+ * Using noninverted ECC can be considered ugly since writing a blank
+ * page ie. padding will clear the ECC bytes. This is no problem as
+ * long nobody is trying to write data on the seemingly unused page.
+ * Reading an erased page will produce an ECC mismatch between
+ * generated and read ECC bytes that has to be dealt with separately.
+ * E.g. if page is 0xFF (fresh erased), and if HW ECC engine within GPMC
+ * is used, the result of read will be 0x0 while the ECC offsets of the
+ * spare area will be 0xFF which will result in an ECC mismatch.
+ * @mtd: MTD structure
+ * @dat: unused
+ * @ecc_code: ecc_code buffer
+ */
+static int omap_calculate_ecc(struct mtd_info *mtd, const uint8_t *dat,
+ uint8_t *ecc_code)
+{
+ u_int32_t val;
+
+ /* Start Reading from HW ECC1_Result = 0x200 */
+ val = readl(&gpmc_base->ecc1_result);
+
+ ecc_code[0] = val & 0xFF;
+ ecc_code[1] = (val >> 16) & 0xFF;
+ ecc_code[2] = ((val >> 8) & 0x0F) | ((val >> 20) & 0xF0);
+
+ /*
+ * Stop reading anymore ECC vals and clear old results
+ * enable will be called if more reads are required
+ */
+ writel(0x000, &gpmc_base->ecc_config);
+
+ return 0;
+}
+
+/*
+ * omap_enable_ecc - This function enables the hardware ecc functionality
+ * @mtd: MTD device structure
+ * @mode: Read/Write mode
+ */
+static void omap_enable_hwecc(struct mtd_info *mtd, int32_t mode)
+{
+ struct nand_chip *chip = mtd->priv;
+ uint32_t val, dev_width = (chip->options & NAND_BUSWIDTH_16) >> 1;
+
+ switch (mode) {
+ case NAND_ECC_READ:
+ case NAND_ECC_WRITE:
+ /* Clear the ecc result registers, select ecc reg as 1 */
+ writel(ECCCLEAR | ECCRESULTREG1, &gpmc_base->ecc_control);
+
+ /*
+ * Size 0 = 0xFF, Size1 is 0xFF - both are 512 bytes
+ * tell all regs to generate size0 sized regs
+ * we just have a single ECC engine for all CS
+ */
+ writel(ECCSIZE1 | ECCSIZE0 | ECCSIZE0SEL,
+ &gpmc_base->ecc_size_config);
+ val = (dev_width << 7) | (cs << 1) | (0x1);
+ writel(val, &gpmc_base->ecc_config);
+ break;
+ default:
+ printf("Error: Unrecognized Mode[%d]!\n", mode);
+ break;
+ }
+}
+
+/*
+ * omap_nand_switch_ecc - switch the ECC operation b/w h/w ecc and s/w ecc.
+ * The default is to come up on s/w ecc
+ *
+ * @hardware - 1 -switch to h/w ecc, 0 - s/w ecc
+ *
+ */
+void omap_nand_switch_ecc(int32_t hardware)
+{
+ struct nand_chip *nand;
+ struct mtd_info *mtd;
+
+ if (nand_curr_device < 0 ||
+ nand_curr_device >= CONFIG_SYS_MAX_NAND_DEVICE ||
+ !nand_info[nand_curr_device].name) {
+ printf("Error: Can't switch ecc, no devices available\n");
+ return;
+ }
+
+ mtd = &nand_info[nand_curr_device];
+ nand = mtd->priv;
+
+ nand->options |= NAND_OWN_BUFFERS;
+
+ /* Reset ecc interface */
+ nand->ecc.read_page = NULL;
+ nand->ecc.write_page = NULL;
+ nand->ecc.read_oob = NULL;
+ nand->ecc.write_oob = NULL;
+ nand->ecc.hwctl = NULL;
+ nand->ecc.correct = NULL;
+ nand->ecc.calculate = NULL;
+
+ /* Setup the ecc configurations again */
+ if (hardware) {
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.layout = &hw_nand_oob;
+ nand->ecc.size = 512;
+ nand->ecc.bytes = 3;
+ nand->ecc.hwctl = omap_enable_hwecc;
+ nand->ecc.correct = omap_correct_data;
+ nand->ecc.calculate = omap_calculate_ecc;
+ omap_hwecc_init(nand);
+ printf("HW ECC selected\n");
+ } else {
+ nand->ecc.mode = NAND_ECC_SOFT;
+ /* Use mtd default settings */
+ nand->ecc.layout = NULL;
+ printf("SW ECC selected\n");
+ }
+
+ /* Update NAND handling after ECC mode switch */
+ nand_scan_tail(mtd);
+
+ nand->options &= ~NAND_OWN_BUFFERS;
+}
+
+/*
+ * Board-specific NAND initialization. The following members of the
+ * argument are board-specific:
+ * - IO_ADDR_R: address to read the 8 I/O lines of the flash device
+ * - IO_ADDR_W: address to write the 8 I/O lines of the flash device
+ * - cmd_ctrl: hardwarespecific function for accesing control-lines
+ * - waitfunc: hardwarespecific function for accesing device ready/busy line
+ * - ecc.hwctl: function to enable (reset) hardware ecc generator
+ * - ecc.mode: mode of ecc, see defines
+ * - chip_delay: chip dependent delay for transfering data from array to
+ * read regs (tR)
+ * - options: various chip options. They can partly be set to inform
+ * nand_scan about special functionality. See the defines for further
+ * explanation
+ */
+int board_nand_init(struct nand_chip *nand)
+{
+ int32_t gpmc_config = 0;
+ cs = 0;
+
+ /*
+ * xloader/Uboot's gpmc configuration would have configured GPMC for
+ * nand type of memory. The following logic scans and latches on to the
+ * first CS with NAND type memory.
+ * TBD: need to make this logic generic to handle multiple CS NAND
+ * devices.
+ */
+ while (cs < GPMC_MAX_CS) {
+ /*
+ * Each GPMC set for a single CS is at offset 0x30
+ * - already remapped for us
+ */
+ gpmc_cs_base = (gpmc_csx_t *)(GPMC_CONFIG_CS0_BASE +
+ (cs * GPMC_CONFIG_WIDTH));
+ /* Check if NAND type is set */
+ if ((readl(&gpmc_cs_base->config1) & 0xC00) ==
+ 0x800) {
+ /* Found it!! */
+ break;
+ }
+ cs++;
+ }
+ if (cs >= GPMC_MAX_CS) {
+ printf("NAND: Unable to find NAND settings in "
+ "GPMC Configuration - quitting\n");
+ return -ENODEV;
+ }
+
+ gpmc_config = readl(&gpmc_base->config);
+ /* Disable Write protect */
+ gpmc_config |= 0x10;
+ writel(gpmc_config, &gpmc_base->config);
+
+ nand->IO_ADDR_R = (void __iomem *)&gpmc_cs_base->nand_dat;
+ nand->IO_ADDR_W = (void __iomem *)&gpmc_cs_base->nand_cmd;
+
+ nand->cmd_ctrl = omap_nand_hwcontrol;
+ nand->options = NAND_NO_PADDING | NAND_CACHEPRG | NAND_NO_AUTOINCR;
+ /* If we are 16 bit dev, our gpmc config tells us that */
+ if ((readl(gpmc_cs_base) & 0x3000) == 0x1000)
+ nand->options |= NAND_BUSWIDTH_16;
+
+ nand->chip_delay = 100;
+ /* Default ECC mode */
+ nand->ecc.mode = NAND_ECC_SOFT;
+
+ return 0;
+}
ifeq ($(BOARD),omap2420h4)
LOAD_ADDR = 0x80300000
else
+ifeq ($(CPU),omap3)
+LOAD_ADDR = 0x80300000
+else
LOAD_ADDR = 0xc100000
endif
endif
+endif
ifeq ($(ARCH),mips)
LOAD_ADDR = 0x80200000 -T mips.lds
#define CCM_PDR1 (CCM_BASE + 0x08)
#define CCM_RCSR (CCM_BASE + 0x0c)
#define CCM_MPCTL (CCM_BASE + 0x10)
-#define CCM_UPCTL (CCM_BASE + 0x10)
+#define CCM_UPCTL (CCM_BASE + 0x14)
#define CCM_SPCTL (CCM_BASE + 0x18)
#define CCM_COSR (CCM_BASE + 0x1C)
#define CCM_CGR0 (CCM_BASE + 0x20)
--- /dev/null
+/*
+ * (C) Copyright 2006-2008
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _CLOCKS_H_
+#define _CLOCKS_H_
+
+#define LDELAY 12000000
+
+#define S12M 12000000
+#define S13M 13000000
+#define S19_2M 19200000
+#define S24M 24000000
+#define S26M 26000000
+#define S38_4M 38400000
+
+#define FCK_IVA2_ON 0x00000001
+#define FCK_CORE1_ON 0x03fffe29
+#define ICK_CORE1_ON 0x3ffffffb
+#define ICK_CORE2_ON 0x0000001f
+#define FCK_WKUP_ON 0x000000e9
+#define ICK_WKUP_ON 0x0000003f
+#define FCK_DSS_ON 0x00000005
+#define ICK_DSS_ON 0x00000001
+#define FCK_CAM_ON 0x00000001
+#define ICK_CAM_ON 0x00000001
+#define FCK_PER_ON 0x0003ffff
+#define ICK_PER_ON 0x0003ffff
+
+/* Used to index into DPLL parameter tables */
+typedef struct {
+ unsigned int m;
+ unsigned int n;
+ unsigned int fsel;
+ unsigned int m2;
+} dpll_param;
+
+/* Following functions are exported from lowlevel_init.S */
+extern dpll_param *get_mpu_dpll_param(void);
+extern dpll_param *get_iva_dpll_param(void);
+extern dpll_param *get_core_dpll_param(void);
+extern dpll_param *get_per_dpll_param(void);
+
+extern void *_end_vect, *_start;
+
+#endif
--- /dev/null
+/*
+ * (C) Copyright 2006-2008
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _CLOCKS_OMAP3_H_
+#define _CLOCKS_OMAP3_H_
+
+#define PLL_STOP 1 /* PER & IVA */
+#define PLL_LOW_POWER_BYPASS 5 /* MPU, IVA & CORE */
+#define PLL_FAST_RELOCK_BYPASS 6 /* CORE */
+#define PLL_LOCK 7 /* MPU, IVA, CORE & PER */
+
+/*
+ * The following configurations are OPP and SysClk value independant
+ * and hence are defined here. All the other DPLL related values are
+ * tabulated in lowlevel_init.S.
+ */
+
+/* CORE DPLL */
+#define CORE_M3X2 2 /* 332MHz : CM_CLKSEL1_EMU */
+#define CORE_SSI_DIV 3 /* 221MHz : CM_CLKSEL_CORE */
+#define CORE_FUSB_DIV 2 /* 41.5MHz: */
+#define CORE_L4_DIV 2 /* 83MHz : L4 */
+#define CORE_L3_DIV 2 /* 166MHz : L3 {DDR} */
+#define GFX_DIV 2 /* 83MHz : CM_CLKSEL_GFX */
+#define WKUP_RSM 2 /* 41.5MHz: CM_CLKSEL_WKUP */
+
+/* PER DPLL */
+#define PER_M6X2 3 /* 288MHz: CM_CLKSEL1_EMU */
+#define PER_M5X2 4 /* 216MHz: CM_CLKSEL_CAM */
+#define PER_M4X2 2 /* 432MHz: CM_CLKSEL_DSS-dss1 */
+#define PER_M3X2 16 /* 54MHz : CM_CLKSEL_DSS-tv */
+
+#define CLSEL1_EMU_VAL ((CORE_M3X2 << 16) | (PER_M6X2 << 24) | (0x0A50))
+
+/* MPU DPLL */
+
+#define MPU_M_12_ES1 0x0FE
+#define MPU_N_12_ES1 0x07
+#define MPU_FSEL_12_ES1 0x05
+#define MPU_M2_12_ES1 0x01
+
+#define MPU_M_12_ES2 0x0FA
+#define MPU_N_12_ES2 0x05
+#define MPU_FSEL_12_ES2 0x07
+#define MPU_M2_ES2 0x01
+
+#define MPU_M_12 0x085
+#define MPU_N_12 0x05
+#define MPU_FSEL_12 0x07
+#define MPU_M2_12 0x01
+
+#define MPU_M_13_ES1 0x17D
+#define MPU_N_13_ES1 0x0C
+#define MPU_FSEL_13_ES1 0x03
+#define MPU_M2_13_ES1 0x01
+
+#define MPU_M_13_ES2 0x1F4
+#define MPU_N_13_ES2 0x0C
+#define MPU_FSEL_13_ES2 0x03
+#define MPU_M2_13_ES2 0x01
+
+#define MPU_M_13 0x10A
+#define MPU_N_13 0x0C
+#define MPU_FSEL_13 0x03
+#define MPU_M2_13 0x01
+
+#define MPU_M_19P2_ES1 0x179
+#define MPU_N_19P2_ES1 0x12
+#define MPU_FSEL_19P2_ES1 0x04
+#define MPU_M2_19P2_ES1 0x01
+
+#define MPU_M_19P2_ES2 0x271
+#define MPU_N_19P2_ES2 0x17
+#define MPU_FSEL_19P2_ES2 0x03
+#define MPU_M2_19P2_ES2 0x01
+
+#define MPU_M_19P2 0x14C
+#define MPU_N_19P2 0x17
+#define MPU_FSEL_19P2 0x03
+#define MPU_M2_19P2 0x01
+
+#define MPU_M_26_ES1 0x17D
+#define MPU_N_26_ES1 0x19
+#define MPU_FSEL_26_ES1 0x03
+#define MPU_M2_26_ES1 0x01
+
+#define MPU_M_26_ES2 0x0FA
+#define MPU_N_26_ES2 0x0C
+#define MPU_FSEL_26_ES2 0x07
+#define MPU_M2_26_ES2 0x01
+
+#define MPU_M_26 0x085
+#define MPU_N_26 0x0C
+#define MPU_FSEL_26 0x07
+#define MPU_M2_26 0x01
+
+#define MPU_M_38P4_ES1 0x1FA
+#define MPU_N_38P4_ES1 0x32
+#define MPU_FSEL_38P4_ES1 0x03
+#define MPU_M2_38P4_ES1 0x01
+
+#define MPU_M_38P4_ES2 0x271
+#define MPU_N_38P4_ES2 0x2F
+#define MPU_FSEL_38P4_ES2 0x03
+#define MPU_M2_38P4_ES2 0x01
+
+#define MPU_M_38P4 0x14C
+#define MPU_N_38P4 0x2F
+#define MPU_FSEL_38P4 0x03
+#define MPU_M2_38P4 0x01
+
+/* IVA DPLL */
+
+#define IVA_M_12_ES1 0x07D
+#define IVA_N_12_ES1 0x05
+#define IVA_FSEL_12_ES1 0x07
+#define IVA_M2_12_ES1 0x01
+
+#define IVA_M_12_ES2 0x0B4
+#define IVA_N_12_ES2 0x05
+#define IVA_FSEL_12_ES2 0x07
+#define IVA_M2_12_ES2 0x01
+
+#define IVA_M_12 0x085
+#define IVA_N_12 0x05
+#define IVA_FSEL_12 0x07
+#define IVA_M2_12 0x01
+
+#define IVA_M_13_ES1 0x0FA
+#define IVA_N_13_ES1 0x0C
+#define IVA_FSEL_13_ES1 0x03
+#define IVA_M2_13_ES1 0x01
+
+#define IVA_M_13_ES2 0x168
+#define IVA_N_13_ES2 0x0C
+#define IVA_FSEL_13_ES2 0x03
+#define IVA_M2_13_ES2 0x01
+
+#define IVA_M_13 0x10A
+#define IVA_N_13 0x0C
+#define IVA_FSEL_13 0x03
+#define IVA_M2_13 0x01
+
+#define IVA_M_19P2_ES1 0x082
+#define IVA_N_19P2_ES1 0x09
+#define IVA_FSEL_19P2_ES1 0x07
+#define IVA_M2_19P2_ES1 0x01
+
+#define IVA_M_19P2_ES2 0x0E1
+#define IVA_N_19P2_ES2 0x0B
+#define IVA_FSEL_19P2_ES2 0x06
+#define IVA_M2_19P2_ES2 0x01
+
+#define IVA_M_19P2 0x14C
+#define IVA_N_19P2 0x17
+#define IVA_FSEL_19P2 0x03
+#define IVA_M2_19P2 0x01
+
+#define IVA_M_26_ES1 0x07D
+#define IVA_N_26_ES1 0x0C
+#define IVA_FSEL_26_ES1 0x07
+#define IVA_M2_26_ES1 0x01
+
+#define IVA_M_26_ES2 0x0B4
+#define IVA_N_26_ES2 0x0C
+#define IVA_FSEL_26_ES2 0x07
+#define IVA_M2_26_ES2 0x01
+
+#define IVA_M_26 0x085
+#define IVA_N_26 0x0C
+#define IVA_FSEL_26 0x07
+#define IVA_M2_26 0x01
+
+#define IVA_M_38P4_ES1 0x13F
+#define IVA_N_38P4_ES1 0x30
+#define IVA_FSEL_38P4_ES1 0x03
+#define IVA_M2_38P4_ES1 0x01
+
+#define IVA_M_38P4_ES2 0x0E1
+#define IVA_N_38P4_ES2 0x17
+#define IVA_FSEL_38P4_ES2 0x06
+#define IVA_M2_38P4_ES2 0x01
+
+#define IVA_M_38P4 0x14C
+#define IVA_N_38P4 0x2F
+#define IVA_FSEL_38P4 0x03
+#define IVA_M2_38P4 0x01
+
+/* CORE DPLL */
+
+#define CORE_M_12 0xA6
+#define CORE_N_12 0x05
+#define CORE_FSEL_12 0x07
+#define CORE_M2_12 0x01 /* M3 of 2 */
+
+#define CORE_M_12_ES1 0x19F
+#define CORE_N_12_ES1 0x0E
+#define CORE_FSL_12_ES1 0x03
+#define CORE_M2_12_ES1 0x1 /* M3 of 2 */
+
+#define CORE_M_13 0x14C
+#define CORE_N_13 0x0C
+#define CORE_FSEL_13 0x03
+#define CORE_M2_13 0x01 /* M3 of 2 */
+
+#define CORE_M_13_ES1 0x1B2
+#define CORE_N_13_ES1 0x10
+#define CORE_FSL_13_ES1 0x03
+#define CORE_M2_13_ES1 0x01 /* M3 of 2 */
+
+#define CORE_M_19P2 0x19F
+#define CORE_N_19P2 0x17
+#define CORE_FSEL_19P2 0x03
+#define CORE_M2_19P2 0x01 /* M3 of 2 */
+
+#define CORE_M_19P2_ES1 0x19F
+#define CORE_N_19P2_ES1 0x17
+#define CORE_FSL_19P2_ES1 0x03
+#define CORE_M2_19P2_ES1 0x01 /* M3 of 2 */
+
+#define CORE_M_26 0xA6
+#define CORE_N_26 0x0C
+#define CORE_FSEL_26 0x07
+#define CORE_M2_26 0x01 /* M3 of 2 */
+
+#define CORE_M_26_ES1 0x1B2
+#define CORE_N_26_ES1 0x21
+#define CORE_FSL_26_ES1 0x03
+#define CORE_M2_26_ES1 0x01 /* M3 of 2 */
+
+#define CORE_M_38P4 0x19F
+#define CORE_N_38P4 0x2F
+#define CORE_FSEL_38P4 0x03
+#define CORE_M2_38P4 0x01 /* M3 of 2 */
+
+#define CORE_M_38P4_ES1 0x19F
+#define CORE_N_38P4_ES1 0x2F
+#define CORE_FSL_38P4_ES1 0x03
+#define CORE_M2_38P4_ES1 0x01 /* M3 of 2 */
+
+/* PER DPLL */
+
+#define PER_M_12 0xD8
+#define PER_N_12 0x05
+#define PER_FSEL_12 0x07
+#define PER_M2_12 0x09
+
+#define PER_M_13 0x1B0
+#define PER_N_13 0x0C
+#define PER_FSEL_13 0x03
+#define PER_M2_13 0x09
+
+#define PER_M_19P2 0xE1
+#define PER_N_19P2 0x09
+#define PER_FSEL_19P2 0x07
+#define PER_M2_19P2 0x09
+
+#define PER_M_26 0xD8
+#define PER_N_26 0x0C
+#define PER_FSEL_26 0x07
+#define PER_M2_26 0x09
+
+#define PER_M_38P4 0xE1
+#define PER_N_38P4 0x13
+#define PER_FSEL_38P4 0x07
+#define PER_M2_38P4 0x09
+
+#endif /* endif _CLOCKS_OMAP3_H_ */
--- /dev/null
+/*
+ * (C) Copyright 2006-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#ifndef _CPU_H
+#define _CPU_H
+
+/* Register offsets of common modules */
+/* Control */
+#ifndef __ASSEMBLY__
+typedef struct ctrl {
+ unsigned char res1[0xC0];
+ unsigned short gpmc_nadv_ale; /* 0xC0 */
+ unsigned short gpmc_noe; /* 0xC2 */
+ unsigned short gpmc_nwe; /* 0xC4 */
+ unsigned char res2[0x22A];
+ unsigned int status; /* 0x2F0 */
+} ctrl_t;
+#else /* __ASSEMBLY__ */
+#define CONTROL_STATUS 0x2F0
+#endif /* __ASSEMBLY__ */
+
+/* device type */
+#define DEVICE_MASK (0x7 << 8)
+#define SYSBOOT_MASK 0x1F
+#define TST_DEVICE 0x0
+#define EMU_DEVICE 0x1
+#define HS_DEVICE 0x2
+#define GP_DEVICE 0x3
+
+/* GPMC CS3/cs4/cs6 not avaliable */
+#define GPMC_BASE (OMAP34XX_GPMC_BASE)
+#define GPMC_CONFIG_CS0 0x60
+#define GPMC_CONFIG_CS6 0x150
+#define GPMC_CONFIG_CS0_BASE (GPMC_BASE + GPMC_CONFIG_CS0)
+#define GPMC_CONFIG_CS6_BASE (GPMC_BASE + GPMC_CONFIG_CS6)
+#define GPMC_CONFIG_WP 0x10
+
+#define GPMC_CONFIG_WIDTH 0x30
+
+#ifndef __ASSEMBLY__
+typedef struct gpmc {
+ unsigned char res1[0x10];
+ unsigned int sysconfig; /* 0x10 */
+ unsigned char res2[0x4];
+ unsigned int irqstatus; /* 0x18 */
+ unsigned int irqenable; /* 0x1C */
+ unsigned char res3[0x20];
+ unsigned int timeout_control; /* 0x40 */
+ unsigned char res4[0xC];
+ unsigned int config; /* 0x50 */
+ unsigned int status; /* 0x54 */
+ unsigned char res5[0x19C];
+ unsigned int ecc_config; /* 0x1F4 */
+ unsigned int ecc_control; /* 0x1F8 */
+ unsigned int ecc_size_config; /* 0x1FC */
+ unsigned int ecc1_result; /* 0x200 */
+ unsigned int ecc2_result; /* 0x204 */
+ unsigned int ecc3_result; /* 0x208 */
+ unsigned int ecc4_result; /* 0x20C */
+ unsigned int ecc5_result; /* 0x210 */
+ unsigned int ecc6_result; /* 0x214 */
+ unsigned int ecc7_result; /* 0x218 */
+ unsigned int ecc8_result; /* 0x21C */
+ unsigned int ecc9_result; /* 0x220 */
+} gpmc_t;
+
+typedef struct gpmc_csx {
+ unsigned int config1; /* 0x00 */
+ unsigned int config2; /* 0x04 */
+ unsigned int config3; /* 0x08 */
+ unsigned int config4; /* 0x0C */
+ unsigned int config5; /* 0x10 */
+ unsigned int config6; /* 0x14 */
+ unsigned int config7; /* 0x18 */
+ unsigned int nand_cmd; /* 0x1C */
+ unsigned int nand_adr; /* 0x20 */
+ unsigned int nand_dat; /* 0x24 */
+} gpmc_csx_t;
+#else /* __ASSEMBLY__ */
+#define GPMC_CONFIG1 0x00
+#define GPMC_CONFIG2 0x04
+#define GPMC_CONFIG3 0x08
+#define GPMC_CONFIG4 0x0C
+#define GPMC_CONFIG5 0x10
+#define GPMC_CONFIG6 0x14
+#define GPMC_CONFIG7 0x18
+#endif /* __ASSEMBLY__ */
+
+/* GPMC Mapping */
+#define FLASH_BASE 0x10000000 /* NOR flash, */
+ /* aligned to 256 Meg */
+#define FLASH_BASE_SDPV1 0x04000000 /* NOR flash, */
+ /* aligned to 64 Meg */
+#define FLASH_BASE_SDPV2 0x10000000 /* NOR flash, */
+ /* aligned to 256 Meg */
+#define DEBUG_BASE 0x08000000 /* debug board */
+#define NAND_BASE 0x30000000 /* NAND addr */
+ /* (actual size small port) */
+#define PISMO2_BASE 0x18000000 /* PISMO2 CS1/2 */
+#define ONENAND_MAP 0x20000000 /* OneNand addr */
+ /* (actual size small port) */
+/* SMS */
+#ifndef __ASSEMBLY__
+typedef struct sms {
+ unsigned char res1[0x10];
+ unsigned int sysconfig; /* 0x10 */
+ unsigned char res2[0x34];
+ unsigned int rg_att0; /* 0x48 */
+ unsigned char res3[0x84];
+ unsigned int class_arb0; /* 0xD0 */
+} sms_t;
+#endif /* __ASSEMBLY__ */
+
+#define BURSTCOMPLETE_GROUP7 (0x1 << 31)
+
+/* SDRC */
+#ifndef __ASSEMBLY__
+typedef struct sdrc_cs {
+ unsigned int mcfg; /* 0x80 || 0xB0 */
+ unsigned int mr; /* 0x84 || 0xB4 */
+ unsigned char res1[0x4];
+ unsigned int emr2; /* 0x8C || 0xBC */
+ unsigned char res2[0x14];
+ unsigned int rfr_ctrl; /* 0x84 || 0xD4 */
+ unsigned int manual; /* 0xA8 || 0xD8 */
+ unsigned char res3[0x4];
+} sdrc_cs_t;
+
+typedef struct sdrc_actim {
+ unsigned int ctrla; /* 0x9C || 0xC4 */
+ unsigned int ctrlb; /* 0xA0 || 0xC8 */
+} sdrc_actim_t;
+
+typedef struct sdrc {
+ unsigned char res1[0x10];
+ unsigned int sysconfig; /* 0x10 */
+ unsigned int status; /* 0x14 */
+ unsigned char res2[0x28];
+ unsigned int cs_cfg; /* 0x40 */
+ unsigned int sharing; /* 0x44 */
+ unsigned char res3[0x18];
+ unsigned int dlla_ctrl; /* 0x60 */
+ unsigned int dlla_status; /* 0x64 */
+ unsigned int dllb_ctrl; /* 0x68 */
+ unsigned int dllb_status; /* 0x6C */
+ unsigned int power; /* 0x70 */
+ unsigned char res4[0xC];
+ sdrc_cs_t cs[2]; /* 0x80 || 0xB0 */
+} sdrc_t;
+#endif /* __ASSEMBLY__ */
+
+#define DLLPHASE_90 (0x1 << 1)
+#define LOADDLL (0x1 << 2)
+#define ENADLL (0x1 << 3)
+#define DLL_DELAY_MASK 0xFF00
+#define DLL_NO_FILTER_MASK ((0x1 << 9) | (0x1 << 8))
+
+#define PAGEPOLICY_HIGH (0x1 << 0)
+#define SRFRONRESET (0x1 << 7)
+#define WAKEUPPROC (0x1 << 26)
+
+#define DDR_SDRAM (0x1 << 0)
+#define DEEPPD (0x1 << 3)
+#define B32NOT16 (0x1 << 4)
+#define BANKALLOCATION (0x2 << 6)
+#define RAMSIZE_128 (0x40 << 8) /* RAM size in 2MB chunks */
+#define ADDRMUXLEGACY (0x1 << 19)
+#define CASWIDTH_10BITS (0x5 << 20)
+#define RASWIDTH_13BITS (0x2 << 24)
+#define BURSTLENGTH4 (0x2 << 0)
+#define CASL3 (0x3 << 4)
+#define SDRC_ACTIM_CTRL0_BASE (OMAP34XX_SDRC_BASE + 0x9C)
+#define SDRC_ACTIM_CTRL1_BASE (OMAP34XX_SDRC_BASE + 0xC4)
+#define ARE_ARCV_1 (0x1 << 0)
+#define ARCV (0x4e2 << 8) /* Autorefresh count */
+#define OMAP34XX_SDRC_CS0 0x80000000
+#define OMAP34XX_SDRC_CS1 0xA0000000
+#define CMD_NOP 0x0
+#define CMD_PRECHARGE 0x1
+#define CMD_AUTOREFRESH 0x2
+#define CMD_ENTR_PWRDOWN 0x3
+#define CMD_EXIT_PWRDOWN 0x4
+#define CMD_ENTR_SRFRSH 0x5
+#define CMD_CKE_HIGH 0x6
+#define CMD_CKE_LOW 0x7
+#define SOFTRESET (0x1 << 1)
+#define SMART_IDLE (0x2 << 3)
+#define REF_ON_IDLE (0x1 << 6)
+
+/* timer regs offsets (32 bit regs) */
+
+#ifndef __ASSEMBLY__
+typedef struct gptimer {
+ unsigned int tidr; /* 0x00 r */
+ unsigned char res[0xc];
+ unsigned int tiocp_cfg; /* 0x10 rw */
+ unsigned int tistat; /* 0x14 r */
+ unsigned int tisr; /* 0x18 rw */
+ unsigned int tier; /* 0x1c rw */
+ unsigned int twer; /* 0x20 rw */
+ unsigned int tclr; /* 0x24 rw */
+ unsigned int tcrr; /* 0x28 rw */
+ unsigned int tldr; /* 0x2c rw */
+ unsigned int ttgr; /* 0x30 rw */
+ unsigned int twpc; /* 0x34 r*/
+ unsigned int tmar; /* 0x38 rw*/
+ unsigned int tcar1; /* 0x3c r */
+ unsigned int tcicr; /* 0x40 rw */
+ unsigned int tcar2; /* 0x44 r */
+} gptimer_t;
+#endif /* __ASSEMBLY__ */
+
+/* enable sys_clk NO-prescale /1 */
+#define GPT_EN ((0x0 << 2) | (0x1 << 1) | (0x1 << 0))
+
+/* Watchdog */
+#ifndef __ASSEMBLY__
+typedef struct watchdog {
+ unsigned char res1[0x34];
+ unsigned int wwps; /* 0x34 r */
+ unsigned char res2[0x10];
+ unsigned int wspr; /* 0x48 rw */
+} watchdog_t;
+#endif /* __ASSEMBLY__ */
+
+#define WD_UNLOCK1 0xAAAA
+#define WD_UNLOCK2 0x5555
+
+/* PRCM */
+#define PRCM_BASE 0x48004000
+
+#ifndef __ASSEMBLY__
+typedef struct prcm {
+ unsigned int fclken_iva2; /* 0x00 */
+ unsigned int clken_pll_iva2; /* 0x04 */
+ unsigned char res1[0x1c];
+ unsigned int idlest_pll_iva2; /* 0x24 */
+ unsigned char res2[0x18];
+ unsigned int clksel1_pll_iva2 ; /* 0x40 */
+ unsigned int clksel2_pll_iva2; /* 0x44 */
+ unsigned char res3[0x8bc];
+ unsigned int clken_pll_mpu; /* 0x904 */
+ unsigned char res4[0x1c];
+ unsigned int idlest_pll_mpu; /* 0x924 */
+ unsigned char res5[0x18];
+ unsigned int clksel1_pll_mpu; /* 0x940 */
+ unsigned int clksel2_pll_mpu; /* 0x944 */
+ unsigned char res6[0xb8];
+ unsigned int fclken1_core; /* 0xa00 */
+ unsigned char res7[0xc];
+ unsigned int iclken1_core; /* 0xa10 */
+ unsigned int iclken2_core; /* 0xa14 */
+ unsigned char res8[0x28];
+ unsigned int clksel_core; /* 0xa40 */
+ unsigned char res9[0xbc];
+ unsigned int fclken_gfx; /* 0xb00 */
+ unsigned char res10[0xc];
+ unsigned int iclken_gfx; /* 0xb10 */
+ unsigned char res11[0x2c];
+ unsigned int clksel_gfx; /* 0xb40 */
+ unsigned char res12[0xbc];
+ unsigned int fclken_wkup; /* 0xc00 */
+ unsigned char res13[0xc];
+ unsigned int iclken_wkup; /* 0xc10 */
+ unsigned char res14[0xc];
+ unsigned int idlest_wkup; /* 0xc20 */
+ unsigned char res15[0x1c];
+ unsigned int clksel_wkup; /* 0xc40 */
+ unsigned char res16[0xbc];
+ unsigned int clken_pll; /* 0xd00 */
+ unsigned char res17[0x1c];
+ unsigned int idlest_ckgen; /* 0xd20 */
+ unsigned char res18[0x1c];
+ unsigned int clksel1_pll; /* 0xd40 */
+ unsigned int clksel2_pll; /* 0xd44 */
+ unsigned int clksel3_pll; /* 0xd48 */
+ unsigned char res19[0xb4];
+ unsigned int fclken_dss; /* 0xe00 */
+ unsigned char res20[0xc];
+ unsigned int iclken_dss; /* 0xe10 */
+ unsigned char res21[0x2c];
+ unsigned int clksel_dss; /* 0xe40 */
+ unsigned char res22[0xbc];
+ unsigned int fclken_cam; /* 0xf00 */
+ unsigned char res23[0xc];
+ unsigned int iclken_cam; /* 0xf10 */
+ unsigned char res24[0x2c];
+ unsigned int clksel_cam; /* 0xf40 */
+ unsigned char res25[0xbc];
+ unsigned int fclken_per; /* 0x1000 */
+ unsigned char res26[0xc];
+ unsigned int iclken_per; /* 0x1010 */
+ unsigned char res27[0x2c];
+ unsigned int clksel_per; /* 0x1040 */
+ unsigned char res28[0xfc];
+ unsigned int clksel1_emu; /* 0x1140 */
+} prcm_t;
+#else /* __ASSEMBLY__ */
+#define CM_CLKSEL_CORE 0x48004a40
+#define CM_CLKSEL_GFX 0x48004b40
+#define CM_CLKSEL_WKUP 0x48004c40
+#define CM_CLKEN_PLL 0x48004d00
+#define CM_CLKSEL1_PLL 0x48004d40
+#define CM_CLKSEL1_EMU 0x48005140
+#endif /* __ASSEMBLY__ */
+
+#define PRM_BASE 0x48306000
+
+#ifndef __ASSEMBLY__
+typedef struct prm {
+ unsigned char res1[0xd40];
+ unsigned int clksel; /* 0xd40 */
+ unsigned char res2[0x50c];
+ unsigned int rstctrl; /* 0x1250 */
+ unsigned char res3[0x1c];
+ unsigned int clksrc_ctrl; /* 0x1270 */
+} prm_t;
+#else /* __ASSEMBLY__ */
+#define PRM_RSTCTRL 0x48307250
+#endif /* __ASSEMBLY__ */
+
+#define SYSCLKDIV_1 (0x1 << 6)
+#define SYSCLKDIV_2 (0x1 << 7)
+
+#define CLKSEL_GPT1 (0x1 << 0)
+
+#define EN_GPT1 (0x1 << 0)
+#define EN_32KSYNC (0x1 << 2)
+
+#define ST_WDT2 (0x1 << 5)
+
+#define ST_MPU_CLK (0x1 << 0)
+
+#define ST_CORE_CLK (0x1 << 0)
+
+#define ST_PERIPH_CLK (0x1 << 1)
+
+#define ST_IVA2_CLK (0x1 << 0)
+
+#define RESETDONE (0x1 << 0)
+
+#define TCLR_ST (0x1 << 0)
+#define TCLR_AR (0x1 << 1)
+#define TCLR_PRE (0x1 << 5)
+
+/* SMX-APE */
+#define PM_RT_APE_BASE_ADDR_ARM (SMX_APE_BASE + 0x10000)
+#define PM_GPMC_BASE_ADDR_ARM (SMX_APE_BASE + 0x12400)
+#define PM_OCM_RAM_BASE_ADDR_ARM (SMX_APE_BASE + 0x12800)
+#define PM_IVA2_BASE_ADDR_ARM (SMX_APE_BASE + 0x14000)
+
+#ifndef __ASSEMBLY__
+typedef struct pm {
+ unsigned char res1[0x48];
+ unsigned int req_info_permission_0; /* 0x48 */
+ unsigned char res2[0x4];
+ unsigned int read_permission_0; /* 0x50 */
+ unsigned char res3[0x4];
+ unsigned int wirte_permission_0; /* 0x58 */
+ unsigned char res4[0x4];
+ unsigned int addr_match_1; /* 0x58 */
+ unsigned char res5[0x4];
+ unsigned int req_info_permission_1; /* 0x68 */
+ unsigned char res6[0x14];
+ unsigned int addr_match_2; /* 0x80 */
+} pm_t;
+#endif /*__ASSEMBLY__ */
+
+/* Permission values for registers -Full fledged permissions to all */
+#define UNLOCK_1 0xFFFFFFFF
+#define UNLOCK_2 0x00000000
+#define UNLOCK_3 0x0000FFFF
+
+#define NOT_EARLY 0
+
+/* I2C base */
+#define I2C_BASE1 (OMAP34XX_CORE_L4_IO_BASE + 0x70000)
+#define I2C_BASE2 (OMAP34XX_CORE_L4_IO_BASE + 0x72000)
+#define I2C_BASE3 (OMAP34XX_CORE_L4_IO_BASE + 0x60000)
+
+#endif /* _CPU_H */
--- /dev/null
+/*
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _I2C_H_
+#define _I2C_H_
+
+#define I2C_DEFAULT_BASE I2C_BASE1
+
+#define I2C_REV (I2C_DEFAULT_BASE + 0x00)
+#define I2C_IE (I2C_DEFAULT_BASE + 0x04)
+#define I2C_STAT (I2C_DEFAULT_BASE + 0x08)
+#define I2C_IV (I2C_DEFAULT_BASE + 0x0c)
+#define I2C_BUF (I2C_DEFAULT_BASE + 0x14)
+#define I2C_CNT (I2C_DEFAULT_BASE + 0x18)
+#define I2C_DATA (I2C_DEFAULT_BASE + 0x1c)
+#define I2C_SYSC (I2C_DEFAULT_BASE + 0x20)
+#define I2C_CON (I2C_DEFAULT_BASE + 0x24)
+#define I2C_OA (I2C_DEFAULT_BASE + 0x28)
+#define I2C_SA (I2C_DEFAULT_BASE + 0x2c)
+#define I2C_PSC (I2C_DEFAULT_BASE + 0x30)
+#define I2C_SCLL (I2C_DEFAULT_BASE + 0x34)
+#define I2C_SCLH (I2C_DEFAULT_BASE + 0x38)
+#define I2C_SYSTEST (I2C_DEFAULT_BASE + 0x3c)
+
+/* I2C masks */
+
+/* I2C Interrupt Enable Register (I2C_IE): */
+#define I2C_IE_GC_IE (1 << 5)
+#define I2C_IE_XRDY_IE (1 << 4) /* Transmit data ready interrupt enable */
+#define I2C_IE_RRDY_IE (1 << 3) /* Receive data ready interrupt enable */
+#define I2C_IE_ARDY_IE (1 << 2) /* Register access ready interrupt enable */
+#define I2C_IE_NACK_IE (1 << 1) /* No acknowledgment interrupt enable */
+#define I2C_IE_AL_IE (1 << 0) /* Arbitration lost interrupt enable */
+
+/* I2C Status Register (I2C_STAT): */
+
+#define I2C_STAT_SBD (1 << 15) /* Single byte data */
+#define I2C_STAT_BB (1 << 12) /* Bus busy */
+#define I2C_STAT_ROVR (1 << 11) /* Receive overrun */
+#define I2C_STAT_XUDF (1 << 10) /* Transmit underflow */
+#define I2C_STAT_AAS (1 << 9) /* Address as slave */
+#define I2C_STAT_GC (1 << 5)
+#define I2C_STAT_XRDY (1 << 4) /* Transmit data ready */
+#define I2C_STAT_RRDY (1 << 3) /* Receive data ready */
+#define I2C_STAT_ARDY (1 << 2) /* Register access ready */
+#define I2C_STAT_NACK (1 << 1) /* No acknowledgment interrupt enable */
+#define I2C_STAT_AL (1 << 0) /* Arbitration lost interrupt enable */
+
+/* I2C Interrupt Code Register (I2C_INTCODE): */
+
+#define I2C_INTCODE_MASK 7
+#define I2C_INTCODE_NONE 0
+#define I2C_INTCODE_AL 1 /* Arbitration lost */
+#define I2C_INTCODE_NAK 2 /* No acknowledgement/general call */
+#define I2C_INTCODE_ARDY 3 /* Register access ready */
+#define I2C_INTCODE_RRDY 4 /* Rcv data ready */
+#define I2C_INTCODE_XRDY 5 /* Xmit data ready */
+
+/* I2C Buffer Configuration Register (I2C_BUF): */
+
+#define I2C_BUF_RDMA_EN (1 << 15) /* Receive DMA channel enable */
+#define I2C_BUF_XDMA_EN (1 << 7) /* Transmit DMA channel enable */
+
+/* I2C Configuration Register (I2C_CON): */
+
+#define I2C_CON_EN (1 << 15) /* I2C module enable */
+#define I2C_CON_BE (1 << 14) /* Big endian mode */
+#define I2C_CON_STB (1 << 11) /* Start byte mode (master mode only) */
+#define I2C_CON_MST (1 << 10) /* Master/slave mode */
+#define I2C_CON_TRX (1 << 9) /* Transmitter/receiver mode */
+ /* (master mode only) */
+#define I2C_CON_XA (1 << 8) /* Expand address */
+#define I2C_CON_STP (1 << 1) /* Stop condition (master mode only) */
+#define I2C_CON_STT (1 << 0) /* Start condition (master mode only) */
+
+/* I2C System Test Register (I2C_SYSTEST): */
+
+#define I2C_SYSTEST_ST_EN (1 << 15) /* System test enable */
+#define I2C_SYSTEST_FREE (1 << 14) /* Free running mode, on brkpoint) */
+#define I2C_SYSTEST_TMODE_MASK (3 << 12) /* Test mode select */
+#define I2C_SYSTEST_TMODE_SHIFT (12) /* Test mode select */
+#define I2C_SYSTEST_SCL_I (1 << 3) /* SCL line sense input value */
+#define I2C_SYSTEST_SCL_O (1 << 2) /* SCL line drive output value */
+#define I2C_SYSTEST_SDA_I (1 << 1) /* SDA line sense input value */
+#define I2C_SYSTEST_SDA_O (1 << 0) /* SDA line drive output value */
+
+#define I2C_SCLL_SCLL 0
+#define I2C_SCLL_SCLL_M 0xFF
+#define I2C_SCLL_HSSCLL 8
+#define I2C_SCLH_HSSCLL_M 0xFF
+#define I2C_SCLH_SCLH 0
+#define I2C_SCLH_SCLH_M 0xFF
+#define I2C_SCLH_HSSCLH 8
+#define I2C_SCLH_HSSCLH_M 0xFF
+
+#define OMAP_I2C_STANDARD 100
+#define OMAP_I2C_FAST_MODE 400
+#define OMAP_I2C_HIGH_SPEED 3400
+
+#define SYSTEM_CLOCK_12 12000
+#define SYSTEM_CLOCK_13 13000
+#define SYSTEM_CLOCK_192 19200
+#define SYSTEM_CLOCK_96 96000
+
+#define I2C_IP_CLK SYSTEM_CLOCK_96
+#define I2C_PSC_MAX 0x0f
+#define I2C_PSC_MIN 0x00
+
+#endif /* _I2C_H_ */
--- /dev/null
+/*
+ * (C) Copyright 2006-2008
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _MEM_H_
+#define _MEM_H_
+
+#define CS0 0x0
+#define CS1 0x1 /* mirror CS1 regs appear offset 0x30 from CS0 */
+
+#ifndef __ASSEMBLY__
+typedef enum {
+ STACKED = 0,
+ IP_DDR = 1,
+ COMBO_DDR = 2,
+ IP_SDR = 3,
+} mem_t;
+#endif /* __ASSEMBLY__ */
+
+#define EARLY_INIT 1
+
+/* Slower full frequency range default timings for x32 operation*/
+#define SDP_SDRC_SHARING 0x00000100
+#define SDP_SDRC_MR_0_SDR 0x00000031
+
+/* optimized timings good for current shipping parts */
+#define SDP_3430_SDRC_RFR_CTRL_165MHz 0x0004e201 /* 7.8us/6ns - 50=0x4e2 */
+
+#define DLL_OFFSET 0
+#define DLL_WRITEDDRCLKX2DIS 1
+#define DLL_ENADLL 1
+#define DLL_LOCKDLL 0
+#define DLL_DLLPHASE_72 0
+#define DLL_DLLPHASE_90 1
+
+/* rkw - need to find of 90/72 degree recommendation for speed like before */
+#define SDP_SDRC_DLLAB_CTRL ((DLL_ENADLL << 3) | \
+ (DLL_LOCKDLL << 2) | (DLL_DLLPHASE_90 << 1))
+
+/* Infineon part of 3430SDP (165MHz optimized) 6.06ns
+ * ACTIMA
+ * TDAL = Twr/Tck + Trp/tck = 15/6 + 18/6 = 2.5 + 3 = 5.5 -> 6
+ * TDPL (Twr) = 15/6 = 2.5 -> 3
+ * TRRD = 12/6 = 2
+ * TRCD = 18/6 = 3
+ * TRP = 18/6 = 3
+ * TRAS = 42/6 = 7
+ * TRC = 60/6 = 10
+ * TRFC = 72/6 = 12
+ * ACTIMB
+ * TCKE = 2
+ * XSR = 120/6 = 20
+ */
+#define TDAL_165 6
+#define TDPL_165 3
+#define TRRD_165 2
+#define TRCD_165 3
+#define TRP_165 3
+#define TRAS_165 7
+#define TRC_165 10
+#define TRFC_165 21
+#define V_ACTIMA_165 ((TRFC_165 << 27) | (TRC_165 << 22) | \
+ (TRAS_165 << 18) | (TRP_165 << 15) | \
+ (TRCD_165 << 12) | (TRRD_165 << 9) | \
+ (TDPL_165 << 6) | (TDAL_165))
+
+#define TWTR_165 1
+#define TCKE_165 1
+#define TXP_165 5
+#define XSR_165 23
+#define V_ACTIMB_165 (((TCKE_165 << 12) | (XSR_165 << 0)) | \
+ (TXP_165 << 8) | (TWTR_165 << 16))
+
+#define SDP_SDRC_ACTIM_CTRLA_0 V_ACTIMA_165
+#define SDP_SDRC_ACTIM_CTRLB_0 V_ACTIMB_165
+#define SDP_SDRC_RFR_CTRL SDP_3430_SDRC_RFR_CTRL_165MHz
+
+/*
+ * GPMC settings -
+ * Definitions is as per the following format
+ * #define <PART>_GPMC_CONFIG<x> <value>
+ * Where:
+ * PART is the part name e.g. STNOR - Intel Strata Flash
+ * x is GPMC config registers from 1 to 6 (there will be 6 macros)
+ * Value is corresponding value
+ *
+ * For every valid PRCM configuration there should be only one definition of
+ * the same. if values are independent of the board, this definition will be
+ * present in this file if values are dependent on the board, then this should
+ * go into corresponding mem-boardName.h file
+ *
+ * Currently valid part Names are (PART):
+ * STNOR - Intel Strata Flash
+ * SMNAND - Samsung NAND
+ * MPDB - H4 MPDB board
+ * SBNOR - Sibley NOR
+ * MNAND - Micron Large page x16 NAND
+ * ONNAND - Samsung One NAND
+ *
+ * include/configs/file.h contains the defn - for all CS we are interested
+ * #define OMAP34XX_GPMC_CSx PART
+ * #define OMAP34XX_GPMC_CSx_SIZE Size
+ * #define OMAP34XX_GPMC_CSx_MAP Map
+ * Where:
+ * x - CS number
+ * PART - Part Name as defined above
+ * SIZE - how big is the mapping to be
+ * GPMC_SIZE_128M - 0x8
+ * GPMC_SIZE_64M - 0xC
+ * GPMC_SIZE_32M - 0xE
+ * GPMC_SIZE_16M - 0xF
+ * MAP - Map this CS to which address(GPMC address space)- Absolute address
+ * >>24 before being used.
+ */
+#define GPMC_SIZE_128M 0x8
+#define GPMC_SIZE_64M 0xC
+#define GPMC_SIZE_32M 0xE
+#define GPMC_SIZE_16M 0xF
+
+#define SMNAND_GPMC_CONFIG1 0x00000800
+#define SMNAND_GPMC_CONFIG2 0x00141400
+#define SMNAND_GPMC_CONFIG3 0x00141400
+#define SMNAND_GPMC_CONFIG4 0x0F010F01
+#define SMNAND_GPMC_CONFIG5 0x010C1414
+#define SMNAND_GPMC_CONFIG6 0x1F0F0A80
+#define SMNAND_GPMC_CONFIG7 0x00000C44
+
+#define M_NAND_GPMC_CONFIG1 0x00001800
+#define M_NAND_GPMC_CONFIG2 0x00141400
+#define M_NAND_GPMC_CONFIG3 0x00141400
+#define M_NAND_GPMC_CONFIG4 0x0F010F01
+#define M_NAND_GPMC_CONFIG5 0x010C1414
+#define M_NAND_GPMC_CONFIG6 0x1f0f0A80
+#define M_NAND_GPMC_CONFIG7 0x00000C44
+
+#define STNOR_GPMC_CONFIG1 0x3
+#define STNOR_GPMC_CONFIG2 0x00151501
+#define STNOR_GPMC_CONFIG3 0x00060602
+#define STNOR_GPMC_CONFIG4 0x11091109
+#define STNOR_GPMC_CONFIG5 0x01141F1F
+#define STNOR_GPMC_CONFIG6 0x000004c4
+
+#define SIBNOR_GPMC_CONFIG1 0x1200
+#define SIBNOR_GPMC_CONFIG2 0x001f1f00
+#define SIBNOR_GPMC_CONFIG3 0x00080802
+#define SIBNOR_GPMC_CONFIG4 0x1C091C09
+#define SIBNOR_GPMC_CONFIG5 0x01131F1F
+#define SIBNOR_GPMC_CONFIG6 0x1F0F03C2
+
+#define SDPV2_MPDB_GPMC_CONFIG1 0x00611200
+#define SDPV2_MPDB_GPMC_CONFIG2 0x001F1F01
+#define SDPV2_MPDB_GPMC_CONFIG3 0x00080803
+#define SDPV2_MPDB_GPMC_CONFIG4 0x1D091D09
+#define SDPV2_MPDB_GPMC_CONFIG5 0x041D1F1F
+#define SDPV2_MPDB_GPMC_CONFIG6 0x1D0904C4
+
+#define MPDB_GPMC_CONFIG1 0x00011000
+#define MPDB_GPMC_CONFIG2 0x001f1f01
+#define MPDB_GPMC_CONFIG3 0x00080803
+#define MPDB_GPMC_CONFIG4 0x1c0b1c0a
+#define MPDB_GPMC_CONFIG5 0x041f1F1F
+#define MPDB_GPMC_CONFIG6 0x1F0F04C4
+
+#define P2_GPMC_CONFIG1 0x0
+#define P2_GPMC_CONFIG2 0x0
+#define P2_GPMC_CONFIG3 0x0
+#define P2_GPMC_CONFIG4 0x0
+#define P2_GPMC_CONFIG5 0x0
+#define P2_GPMC_CONFIG6 0x0
+
+#define ONENAND_GPMC_CONFIG1 0x00001200
+#define ONENAND_GPMC_CONFIG2 0x000F0F01
+#define ONENAND_GPMC_CONFIG3 0x00030301
+#define ONENAND_GPMC_CONFIG4 0x0F040F04
+#define ONENAND_GPMC_CONFIG5 0x010F1010
+#define ONENAND_GPMC_CONFIG6 0x1F060000
+
+#define NET_GPMC_CONFIG1 0x00001000
+#define NET_GPMC_CONFIG2 0x001e1e01
+#define NET_GPMC_CONFIG3 0x00080300
+#define NET_GPMC_CONFIG4 0x1c091c09
+#define NET_GPMC_CONFIG5 0x04181f1f
+#define NET_GPMC_CONFIG6 0x00000FCF
+#define NET_GPMC_CONFIG7 0x00000f6c
+
+/* max number of GPMC Chip Selects */
+#define GPMC_MAX_CS 8
+/* max number of GPMC regs */
+#define GPMC_MAX_REG 7
+
+#define PISMO1_NOR 1
+#define PISMO1_NAND 2
+#define PISMO2_CS0 3
+#define PISMO2_CS1 4
+#define PISMO1_ONENAND 5
+#define DBG_MPDB 6
+#define PISMO2_NAND_CS0 7
+#define PISMO2_NAND_CS1 8
+
+/* make it readable for the gpmc_init */
+#define PISMO1_NOR_BASE FLASH_BASE
+#define PISMO1_NAND_BASE NAND_BASE
+#define PISMO2_CS0_BASE PISMO2_MAP1
+#define PISMO1_ONEN_BASE ONENAND_MAP
+#define DBG_MPDB_BASE DEBUG_BASE
+
+#endif /* endif _MEM_H_ */
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Texas Instruments, <www.ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation's version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef MMC_H
+#define MMC_H
+
+#include "mmc_host_def.h"
+
+/* Responses */
+#define RSP_TYPE_NONE (RSP_TYPE_NORSP | CCCE_NOCHECK | CICE_NOCHECK)
+#define RSP_TYPE_R1 (RSP_TYPE_LGHT48 | CCCE_CHECK | CICE_CHECK)
+#define RSP_TYPE_R1B (RSP_TYPE_LGHT48B | CCCE_CHECK | CICE_CHECK)
+#define RSP_TYPE_R2 (RSP_TYPE_LGHT136 | CCCE_CHECK | CICE_NOCHECK)
+#define RSP_TYPE_R3 (RSP_TYPE_LGHT48 | CCCE_NOCHECK | CICE_NOCHECK)
+#define RSP_TYPE_R4 (RSP_TYPE_LGHT48 | CCCE_NOCHECK | CICE_NOCHECK)
+#define RSP_TYPE_R5 (RSP_TYPE_LGHT48 | CCCE_CHECK | CICE_CHECK)
+#define RSP_TYPE_R6 (RSP_TYPE_LGHT48 | CCCE_CHECK | CICE_CHECK)
+#define RSP_TYPE_R7 (RSP_TYPE_LGHT48 | CCCE_CHECK | CICE_CHECK)
+
+/* All supported commands */
+#define MMC_CMD0 (INDEX(0) | RSP_TYPE_NONE | DP_NO_DATA | DDIR_WRITE)
+#define MMC_CMD1 (INDEX(1) | RSP_TYPE_R3 | DP_NO_DATA | DDIR_WRITE)
+#define MMC_CMD2 (INDEX(2) | RSP_TYPE_R2 | DP_NO_DATA | DDIR_WRITE)
+#define MMC_CMD3 (INDEX(3) | RSP_TYPE_R1 | DP_NO_DATA | DDIR_WRITE)
+#define MMC_SDCMD3 (INDEX(3) | RSP_TYPE_R6 | DP_NO_DATA | DDIR_WRITE)
+#define MMC_CMD4 (INDEX(4) | RSP_TYPE_NONE | DP_NO_DATA | DDIR_WRITE)
+#define MMC_CMD6 (INDEX(6) | RSP_TYPE_R1B | DP_NO_DATA | DDIR_WRITE)
+#define MMC_CMD7_SELECT (INDEX(7) | RSP_TYPE_R1B | DP_NO_DATA | DDIR_WRITE)
+#define MMC_CMD7_DESELECT (INDEX(7)| RSP_TYPE_NONE | DP_NO_DATA | DDIR_WRITE)
+#define MMC_CMD8 (INDEX(8) | RSP_TYPE_R1 | DP_DATA | DDIR_READ)
+#define MMC_SDCMD8 (INDEX(8) | RSP_TYPE_R7 | DP_NO_DATA | DDIR_WRITE)
+#define MMC_CMD9 (INDEX(9) | RSP_TYPE_R2 | DP_NO_DATA | DDIR_WRITE)
+#define MMC_CMD12 (INDEX(12) | RSP_TYPE_R1B | DP_NO_DATA | DDIR_WRITE)
+#define MMC_CMD13 (INDEX(13) | RSP_TYPE_R1 | DP_NO_DATA | DDIR_WRITE)
+#define MMC_CMD15 (INDEX(15) | RSP_TYPE_NONE | DP_NO_DATA | DDIR_WRITE)
+#define MMC_CMD16 (INDEX(16) | RSP_TYPE_R1 | DP_NO_DATA | DDIR_WRITE)
+#define MMC_CMD17 (INDEX(17) | RSP_TYPE_R1 | DP_DATA | DDIR_READ)
+#define MMC_CMD24 (INDEX(24) | RSP_TYPE_R1 | DP_DATA | DDIR_WRITE)
+#define MMC_ACMD6 (INDEX(6) | RSP_TYPE_R1 | DP_NO_DATA | DDIR_WRITE)
+#define MMC_ACMD41 (INDEX(41) | RSP_TYPE_R3 | DP_NO_DATA | DDIR_WRITE)
+#define MMC_ACMD51 (INDEX(51) | RSP_TYPE_R1 | DP_DATA | DDIR_READ)
+#define MMC_CMD55 (INDEX(55) | RSP_TYPE_R1 | DP_NO_DATA | DDIR_WRITE)
+
+#define MMC_AC_CMD_RCA_MASK (unsigned int)(0xFFFF << 16)
+#define MMC_BC_CMD_DSR_MASK (unsigned int)(0xFFFF << 16)
+#define MMC_DSR_DEFAULT 0x0404
+#define SD_CMD8_CHECK_PATTERN 0xAA
+#define SD_CMD8_2_7_3_6_V_RANGE (0x01 << 8)
+
+/* Clock Configurations and Macros */
+
+#define MMC_CLOCK_REFERENCE 96
+#define MMC_RELATIVE_CARD_ADDRESS 0x1234
+#define MMC_INIT_SEQ_CLK (MMC_CLOCK_REFERENCE * 1000 / 80)
+#define MMC_400kHz_CLK (MMC_CLOCK_REFERENCE * 1000 / 400)
+#define CLKDR(r, f, u) ((((r)*100) / ((f)*(u))) + 1)
+#define CLKD(f, u) (CLKDR(MMC_CLOCK_REFERENCE, f, u))
+
+#define MMC_OCR_REG_ACCESS_MODE_MASK (0x3 << 29)
+#define MMC_OCR_REG_ACCESS_MODE_BYTE (0x0 << 29)
+#define MMC_OCR_REG_ACCESS_MODE_SECTOR (0x2 << 29)
+
+#define MMC_OCR_REG_HOST_CAPACITY_SUPPORT_MASK (0x1 << 30)
+#define MMC_OCR_REG_HOST_CAPACITY_SUPPORT_BYTE (0x0 << 30)
+#define MMC_OCR_REG_HOST_CAPACITY_SUPPORT_SECTOR (0x1 << 30)
+
+#define MMC_SD2_CSD_C_SIZE_LSB_MASK 0xFFFF
+#define MMC_SD2_CSD_C_SIZE_MSB_MASK 0x003F
+#define MMC_SD2_CSD_C_SIZE_MSB_OFFSET 16
+#define MMC_CSD_C_SIZE_LSB_MASK 0x0003
+#define MMC_CSD_C_SIZE_MSB_MASK 0x03FF
+#define MMC_CSD_C_SIZE_MSB_OFFSET 2
+
+#define MMC_CSD_TRAN_SPEED_UNIT_MASK (0x07 << 0)
+#define MMC_CSD_TRAN_SPEED_FACTOR_MASK (0x0F << 3)
+#define MMC_CSD_TRAN_SPEED_UNIT_100MHZ (0x3 << 0)
+#define MMC_CSD_TRAN_SPEED_FACTOR_1_0 (0x01 << 3)
+#define MMC_CSD_TRAN_SPEED_FACTOR_8_0 (0x0F << 3)
+
+typedef struct {
+ unsigned not_used:1;
+ unsigned crc:7;
+ unsigned ecc:2;
+ unsigned file_format:2;
+ unsigned tmp_write_protect:1;
+ unsigned perm_write_protect:1;
+ unsigned copy:1;
+ unsigned file_format_grp:1;
+ unsigned content_prot_app:1;
+ unsigned reserved_1:4;
+ unsigned write_bl_partial:1;
+ unsigned write_bl_len:4;
+ unsigned r2w_factor:3;
+ unsigned default_ecc:2;
+ unsigned wp_grp_enable:1;
+ unsigned wp_grp_size:5;
+ unsigned erase_grp_mult:5;
+ unsigned erase_grp_size:5;
+ unsigned c_size_mult:3;
+ unsigned vdd_w_curr_max:3;
+ unsigned vdd_w_curr_min:3;
+ unsigned vdd_r_curr_max:3;
+ unsigned vdd_r_curr_min:3;
+ unsigned c_size_lsb:2;
+ unsigned c_size_msb:10;
+ unsigned reserved_2:2;
+ unsigned dsr_imp:1;
+ unsigned read_blk_misalign:1;
+ unsigned write_blk_misalign:1;
+ unsigned read_bl_partial:1;
+ unsigned read_bl_len:4;
+ unsigned ccc:12;
+ unsigned tran_speed:8;
+ unsigned nsac:8;
+ unsigned taac:8;
+ unsigned reserved_3:2;
+ unsigned spec_vers:4;
+ unsigned csd_structure:2;
+} mmc_csd_reg_t;
+
+/* csd for sd2.0 */
+typedef struct {
+ unsigned not_used:1;
+ unsigned crc:7;
+ unsigned reserved_1:2;
+ unsigned file_format:2;
+ unsigned tmp_write_protect:1;
+ unsigned perm_write_protect:1;
+ unsigned copy:1;
+ unsigned file_format_grp:1;
+ unsigned reserved_2:5;
+ unsigned write_bl_partial:1;
+ unsigned write_bl_len:4;
+ unsigned r2w_factor:3;
+ unsigned reserved_3:2;
+ unsigned wp_grp_enable:1;
+ unsigned wp_grp_size:7;
+ unsigned sector_size:7;
+ unsigned erase_blk_len:1;
+ unsigned reserved_4:1;
+ unsigned c_size_lsb:16;
+ unsigned c_size_msb:6;
+ unsigned reserved_5:6;
+ unsigned dsr_imp:1;
+ unsigned read_blk_misalign:1;
+ unsigned write_blk_misalign:1;
+ unsigned read_bl_partial:1;
+ unsigned read_bl_len:4;
+ unsigned ccc:12;
+ unsigned tran_speed:8;
+ unsigned nsac:8;
+ unsigned taac:8;
+ unsigned reserved_6:6;
+ unsigned csd_structure:2;
+} mmc_sd2_csd_reg_t;
+
+/* extended csd - 512 bytes long */
+typedef struct {
+ unsigned char reserved_1[181];
+ unsigned char erasedmemorycontent;
+ unsigned char reserved_2;
+ unsigned char buswidthmode;
+ unsigned char reserved_3;
+ unsigned char highspeedinterfacetiming;
+ unsigned char reserved_4;
+ unsigned char powerclass;
+ unsigned char reserved_5;
+ unsigned char commandsetrevision;
+ unsigned char reserved_6;
+ unsigned char commandset;
+ unsigned char extendedcsdrevision;
+ unsigned char reserved_7;
+ unsigned char csdstructureversion;
+ unsigned char reserved_8;
+ unsigned char cardtype;
+ unsigned char reserved_9[3];
+ unsigned char powerclass_52mhz_1_95v;
+ unsigned char powerclass_26mhz_1_95v;
+ unsigned char powerclass_52mhz_3_6v;
+ unsigned char powerclass_26mhz_3_6v;
+ unsigned char reserved_10;
+ unsigned char minreadperf_4b_26mhz;
+ unsigned char minwriteperf_4b_26mhz;
+ unsigned char minreadperf_8b_26mhz_4b_52mhz;
+ unsigned char minwriteperf_8b_26mhz_4b_52mhz;
+ unsigned char minreadperf_8b_52mhz;
+ unsigned char minwriteperf_8b_52mhz;
+ unsigned char reserved_11;
+ unsigned int sectorcount;
+ unsigned char reserved_12[288];
+ unsigned char supportedcommandsets;
+ unsigned char reserved_13[7];
+} mmc_extended_csd_reg_t;
+
+/* mmc sd responce */
+typedef struct {
+ unsigned int ocr;
+} mmc_resp_r3;
+
+typedef struct {
+ unsigned short cardstatus;
+ unsigned short newpublishedrca;
+} mmc_resp_r6;
+
+extern mmc_card_data mmc_dev;
+
+unsigned char mmc_lowlevel_init(void);
+unsigned char mmc_send_command(unsigned int cmd, unsigned int arg,
+ unsigned int *response);
+unsigned char mmc_setup_clock(unsigned int iclk, unsigned short clkd);
+unsigned char mmc_set_opendrain(unsigned char state);
+unsigned char mmc_read_data(unsigned int *output_buf);
+
+#endif /* MMC_H */
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Texas Instruments, <www.ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation's version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef MMC_HOST_DEF_H
+#define MMC_HOST_DEF_H
+
+/*
+ * OMAP HSMMC register definitions
+ */
+#define OMAP_HSMMC_SYSCONFIG (*(unsigned int *) 0x4809C010)
+#define OMAP_HSMMC_SYSSTATUS (*(unsigned int *) 0x4809C014)
+#define OMAP_HSMMC_CON (*(unsigned int *) 0x4809C02C)
+#define OMAP_HSMMC_BLK (*(unsigned int *) 0x4809C104)
+#define OMAP_HSMMC_ARG (*(unsigned int *) 0x4809C108)
+#define OMAP_HSMMC_CMD (*(unsigned int *) 0x4809C10C)
+#define OMAP_HSMMC_RSP10 (*(unsigned int *) 0x4809C110)
+#define OMAP_HSMMC_RSP32 (*(unsigned int *) 0x4809C114)
+#define OMAP_HSMMC_RSP54 (*(unsigned int *) 0x4809C118)
+#define OMAP_HSMMC_RSP76 (*(unsigned int *) 0x4809C11C)
+#define OMAP_HSMMC_DATA (*(unsigned int *) 0x4809C120)
+#define OMAP_HSMMC_PSTATE (*(unsigned int *) 0x4809C124)
+#define OMAP_HSMMC_HCTL (*(unsigned int *) 0x4809C128)
+#define OMAP_HSMMC_SYSCTL (*(unsigned int *) 0x4809C12C)
+#define OMAP_HSMMC_STAT (*(unsigned int *) 0x4809C130)
+#define OMAP_HSMMC_IE (*(unsigned int *) 0x4809C134)
+#define OMAP_HSMMC_CAPA (*(unsigned int *) 0x4809C140)
+
+/* T2 Register definitions */
+#define CONTROL_DEV_CONF0 (*(unsigned int *) 0x48002274)
+#define CONTROL_PBIAS_LITE (*(unsigned int *) 0x48002520)
+
+/*
+ * OMAP HS MMC Bit definitions
+ */
+#define MMC_SOFTRESET (0x1 << 1)
+#define RESETDONE (0x1 << 0)
+#define NOOPENDRAIN (0x0 << 0)
+#define OPENDRAIN (0x1 << 0)
+#define OD (0x1 << 0)
+#define INIT_NOINIT (0x0 << 1)
+#define INIT_INITSTREAM (0x1 << 1)
+#define HR_NOHOSTRESP (0x0 << 2)
+#define STR_BLOCK (0x0 << 3)
+#define MODE_FUNC (0x0 << 4)
+#define DW8_1_4BITMODE (0x0 << 5)
+#define MIT_CTO (0x0 << 6)
+#define CDP_ACTIVEHIGH (0x0 << 7)
+#define WPP_ACTIVEHIGH (0x0 << 8)
+#define RESERVED_MASK (0x3 << 9)
+#define CTPL_MMC_SD (0x0 << 11)
+#define BLEN_512BYTESLEN (0x200 << 0)
+#define NBLK_STPCNT (0x0 << 16)
+#define DE_DISABLE (0x0 << 0)
+#define BCE_DISABLE (0x0 << 1)
+#define ACEN_DISABLE (0x0 << 2)
+#define DDIR_OFFSET (4)
+#define DDIR_MASK (0x1 << 4)
+#define DDIR_WRITE (0x0 << 4)
+#define DDIR_READ (0x1 << 4)
+#define MSBS_SGLEBLK (0x0 << 5)
+#define RSP_TYPE_OFFSET (16)
+#define RSP_TYPE_MASK (0x3 << 16)
+#define RSP_TYPE_NORSP (0x0 << 16)
+#define RSP_TYPE_LGHT136 (0x1 << 16)
+#define RSP_TYPE_LGHT48 (0x2 << 16)
+#define RSP_TYPE_LGHT48B (0x3 << 16)
+#define CCCE_NOCHECK (0x0 << 19)
+#define CCCE_CHECK (0x1 << 19)
+#define CICE_NOCHECK (0x0 << 20)
+#define CICE_CHECK (0x1 << 20)
+#define DP_OFFSET (21)
+#define DP_MASK (0x1 << 21)
+#define DP_NO_DATA (0x0 << 21)
+#define DP_DATA (0x1 << 21)
+#define CMD_TYPE_NORMAL (0x0 << 22)
+#define INDEX_OFFSET (24)
+#define INDEX_MASK (0x3f << 24)
+#define INDEX(i) (i << 24)
+#define DATI_MASK (0x1 << 1)
+#define DATI_CMDDIS (0x1 << 1)
+#define DTW_1_BITMODE (0x0 << 1)
+#define DTW_4_BITMODE (0x1 << 1)
+#define SDBP_PWROFF (0x0 << 8)
+#define SDBP_PWRON (0x1 << 8)
+#define SDVS_1V8 (0x5 << 9)
+#define SDVS_3V0 (0x6 << 9)
+#define ICE_MASK (0x1 << 0)
+#define ICE_STOP (0x0 << 0)
+#define ICS_MASK (0x1 << 1)
+#define ICS_NOTREADY (0x0 << 1)
+#define ICE_OSCILLATE (0x1 << 0)
+#define CEN_MASK (0x1 << 2)
+#define CEN_DISABLE (0x0 << 2)
+#define CEN_ENABLE (0x1 << 2)
+#define CLKD_OFFSET (6)
+#define CLKD_MASK (0x3FF << 6)
+#define DTO_MASK (0xF << 16)
+#define DTO_15THDTO (0xE << 16)
+#define SOFTRESETALL (0x1 << 24)
+#define CC_MASK (0x1 << 0)
+#define TC_MASK (0x1 << 1)
+#define BWR_MASK (0x1 << 4)
+#define BRR_MASK (0x1 << 5)
+#define ERRI_MASK (0x1 << 15)
+#define IE_CC (0x01 << 0)
+#define IE_TC (0x01 << 1)
+#define IE_BWR (0x01 << 4)
+#define IE_BRR (0x01 << 5)
+#define IE_CTO (0x01 << 16)
+#define IE_CCRC (0x01 << 17)
+#define IE_CEB (0x01 << 18)
+#define IE_CIE (0x01 << 19)
+#define IE_DTO (0x01 << 20)
+#define IE_DCRC (0x01 << 21)
+#define IE_DEB (0x01 << 22)
+#define IE_CERR (0x01 << 28)
+#define IE_BADA (0x01 << 29)
+
+#define VS30_3V0SUP (1 << 25)
+#define VS18_1V8SUP (1 << 26)
+
+/* Driver definitions */
+#define MMCSD_SECTOR_SIZE 512
+#define MMC_CARD 0
+#define SD_CARD 1
+#define BYTE_MODE 0
+#define SECTOR_MODE 1
+#define CLK_INITSEQ 0
+#define CLK_400KHZ 1
+#define CLK_MISC 2
+
+typedef struct {
+ unsigned int card_type;
+ unsigned int version;
+ unsigned int mode;
+ unsigned int size;
+ unsigned int RCA;
+} mmc_card_data;
+
+#define mmc_reg_out(addr, mask, val)\
+ (addr) = (((addr)) & (~(mask))) | ((val) & (mask));
+#define mmc_reg_out(addr, mask, val)\
+ (addr) = (((addr)) & (~(mask))) | ((val) & (mask));
+
+#endif /* MMC_HOST_DEF_H */
--- /dev/null
+/*
+ * (C) Copyright 2006-2008
+ * Texas Instruments, <www.ti.com>
+ * Syed Mohammed Khasim <x0khasim@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _MUX_H_
+#define _MUX_H_
+
+/*
+ * IEN - Input Enable
+ * IDIS - Input Disable
+ * PTD - Pull type Down
+ * PTU - Pull type Up
+ * DIS - Pull type selection is inactive
+ * EN - Pull type selection is active
+ * M0 - Mode 0
+ */
+
+#define IEN (1 << 8)
+
+#define IDIS (0 << 8)
+#define PTU (1 << 4)
+#define PTD (0 << 4)
+#define EN (1 << 3)
+#define DIS (0 << 3)
+
+#define M0 0
+#define M1 1
+#define M2 2
+#define M3 3
+#define M4 4
+#define M5 5
+#define M6 6
+#define M7 7
+
+/*
+ * To get the actual address the offset has to added
+ * with OMAP34XX_CTRL_BASE to get the actual address
+ */
+
+/*SDRC*/
+#define CONTROL_PADCONF_SDRC_D0 0x0030
+#define CONTROL_PADCONF_SDRC_D1 0x0032
+#define CONTROL_PADCONF_SDRC_D2 0x0034
+#define CONTROL_PADCONF_SDRC_D3 0x0036
+#define CONTROL_PADCONF_SDRC_D4 0x0038
+#define CONTROL_PADCONF_SDRC_D5 0x003A
+#define CONTROL_PADCONF_SDRC_D6 0x003C
+#define CONTROL_PADCONF_SDRC_D7 0x003E
+#define CONTROL_PADCONF_SDRC_D8 0x0040
+#define CONTROL_PADCONF_SDRC_D9 0x0042
+#define CONTROL_PADCONF_SDRC_D10 0x0044
+#define CONTROL_PADCONF_SDRC_D11 0x0046
+#define CONTROL_PADCONF_SDRC_D12 0x0048
+#define CONTROL_PADCONF_SDRC_D13 0x004A
+#define CONTROL_PADCONF_SDRC_D14 0x004C
+#define CONTROL_PADCONF_SDRC_D15 0x004E
+#define CONTROL_PADCONF_SDRC_D16 0x0050
+#define CONTROL_PADCONF_SDRC_D17 0x0052
+#define CONTROL_PADCONF_SDRC_D18 0x0054
+#define CONTROL_PADCONF_SDRC_D19 0x0056
+#define CONTROL_PADCONF_SDRC_D20 0x0058
+#define CONTROL_PADCONF_SDRC_D21 0x005A
+#define CONTROL_PADCONF_SDRC_D22 0x005C
+#define CONTROL_PADCONF_SDRC_D23 0x005E
+#define CONTROL_PADCONF_SDRC_D24 0x0060
+#define CONTROL_PADCONF_SDRC_D25 0x0062
+#define CONTROL_PADCONF_SDRC_D26 0x0064
+#define CONTROL_PADCONF_SDRC_D27 0x0066
+#define CONTROL_PADCONF_SDRC_D28 0x0068
+#define CONTROL_PADCONF_SDRC_D29 0x006A
+#define CONTROL_PADCONF_SDRC_D30 0x006C
+#define CONTROL_PADCONF_SDRC_D31 0x006E
+#define CONTROL_PADCONF_SDRC_CLK 0x0070
+#define CONTROL_PADCONF_SDRC_DQS0 0x0072
+#define CONTROL_PADCONF_SDRC_DQS1 0x0074
+#define CONTROL_PADCONF_SDRC_DQS2 0x0076
+#define CONTROL_PADCONF_SDRC_DQS3 0x0078
+/*GPMC*/
+#define CONTROL_PADCONF_GPMC_A1 0x007A
+#define CONTROL_PADCONF_GPMC_A2 0x007C
+#define CONTROL_PADCONF_GPMC_A3 0x007E
+#define CONTROL_PADCONF_GPMC_A4 0x0080
+#define CONTROL_PADCONF_GPMC_A5 0x0082
+#define CONTROL_PADCONF_GPMC_A6 0x0084
+#define CONTROL_PADCONF_GPMC_A7 0x0086
+#define CONTROL_PADCONF_GPMC_A8 0x0088
+#define CONTROL_PADCONF_GPMC_A9 0x008A
+#define CONTROL_PADCONF_GPMC_A10 0x008C
+#define CONTROL_PADCONF_GPMC_D0 0x008E
+#define CONTROL_PADCONF_GPMC_D1 0x0090
+#define CONTROL_PADCONF_GPMC_D2 0x0092
+#define CONTROL_PADCONF_GPMC_D3 0x0094
+#define CONTROL_PADCONF_GPMC_D4 0x0096
+#define CONTROL_PADCONF_GPMC_D5 0x0098
+#define CONTROL_PADCONF_GPMC_D6 0x009A
+#define CONTROL_PADCONF_GPMC_D7 0x009C
+#define CONTROL_PADCONF_GPMC_D8 0x009E
+#define CONTROL_PADCONF_GPMC_D9 0x00A0
+#define CONTROL_PADCONF_GPMC_D10 0x00A2
+#define CONTROL_PADCONF_GPMC_D11 0x00A4
+#define CONTROL_PADCONF_GPMC_D12 0x00A6
+#define CONTROL_PADCONF_GPMC_D13 0x00A8
+#define CONTROL_PADCONF_GPMC_D14 0x00AA
+#define CONTROL_PADCONF_GPMC_D15 0x00AC
+#define CONTROL_PADCONF_GPMC_NCS0 0x00AE
+#define CONTROL_PADCONF_GPMC_NCS1 0x00B0
+#define CONTROL_PADCONF_GPMC_NCS2 0x00B2
+#define CONTROL_PADCONF_GPMC_NCS3 0x00B4
+#define CONTROL_PADCONF_GPMC_NCS4 0x00B6
+#define CONTROL_PADCONF_GPMC_NCS5 0x00B8
+#define CONTROL_PADCONF_GPMC_NCS6 0x00BA
+#define CONTROL_PADCONF_GPMC_NCS7 0x00BC
+#define CONTROL_PADCONF_GPMC_CLK 0x00BE
+#define CONTROL_PADCONF_GPMC_NADV_ALE 0x00C0
+#define CONTROL_PADCONF_GPMC_NOE 0x00C2
+#define CONTROL_PADCONF_GPMC_NWE 0x00C4
+#define CONTROL_PADCONF_GPMC_NBE0_CLE 0x00C6
+#define CONTROL_PADCONF_GPMC_NBE1 0x00C8
+#define CONTROL_PADCONF_GPMC_NWP 0x00CA
+#define CONTROL_PADCONF_GPMC_WAIT0 0x00CC
+#define CONTROL_PADCONF_GPMC_WAIT1 0x00CE
+#define CONTROL_PADCONF_GPMC_WAIT2 0x00D0
+#define CONTROL_PADCONF_GPMC_WAIT3 0x00D2
+/*DSS*/
+#define CONTROL_PADCONF_DSS_PCLK 0x00D4
+#define CONTROL_PADCONF_DSS_HSYNC 0x00D6
+#define CONTROL_PADCONF_DSS_VSYNC 0x00D8
+#define CONTROL_PADCONF_DSS_ACBIAS 0x00DA
+#define CONTROL_PADCONF_DSS_DATA0 0x00DC
+#define CONTROL_PADCONF_DSS_DATA1 0x00DE
+#define CONTROL_PADCONF_DSS_DATA2 0x00E0
+#define CONTROL_PADCONF_DSS_DATA3 0x00E2
+#define CONTROL_PADCONF_DSS_DATA4 0x00E4
+#define CONTROL_PADCONF_DSS_DATA5 0x00E6
+#define CONTROL_PADCONF_DSS_DATA6 0x00E8
+#define CONTROL_PADCONF_DSS_DATA7 0x00EA
+#define CONTROL_PADCONF_DSS_DATA8 0x00EC
+#define CONTROL_PADCONF_DSS_DATA9 0x00EE
+#define CONTROL_PADCONF_DSS_DATA10 0x00F0
+#define CONTROL_PADCONF_DSS_DATA11 0x00F2
+#define CONTROL_PADCONF_DSS_DATA12 0x00F4
+#define CONTROL_PADCONF_DSS_DATA13 0x00F6
+#define CONTROL_PADCONF_DSS_DATA14 0x00F8
+#define CONTROL_PADCONF_DSS_DATA15 0x00FA
+#define CONTROL_PADCONF_DSS_DATA16 0x00FC
+#define CONTROL_PADCONF_DSS_DATA17 0x00FE
+#define CONTROL_PADCONF_DSS_DATA18 0x0100
+#define CONTROL_PADCONF_DSS_DATA19 0x0102
+#define CONTROL_PADCONF_DSS_DATA20 0x0104
+#define CONTROL_PADCONF_DSS_DATA21 0x0106
+#define CONTROL_PADCONF_DSS_DATA22 0x0108
+#define CONTROL_PADCONF_DSS_DATA23 0x010A
+/*CAMERA*/
+#define CONTROL_PADCONF_CAM_HS 0x010C
+#define CONTROL_PADCONF_CAM_VS 0x010E
+#define CONTROL_PADCONF_CAM_XCLKA 0x0110
+#define CONTROL_PADCONF_CAM_PCLK 0x0112
+#define CONTROL_PADCONF_CAM_FLD 0x0114
+#define CONTROL_PADCONF_CAM_D0 0x0116
+#define CONTROL_PADCONF_CAM_D1 0x0118
+#define CONTROL_PADCONF_CAM_D2 0x011A
+#define CONTROL_PADCONF_CAM_D3 0x011C
+#define CONTROL_PADCONF_CAM_D4 0x011E
+#define CONTROL_PADCONF_CAM_D5 0x0120
+#define CONTROL_PADCONF_CAM_D6 0x0122
+#define CONTROL_PADCONF_CAM_D7 0x0124
+#define CONTROL_PADCONF_CAM_D8 0x0126
+#define CONTROL_PADCONF_CAM_D9 0x0128
+#define CONTROL_PADCONF_CAM_D10 0x012A
+#define CONTROL_PADCONF_CAM_D11 0x012C
+#define CONTROL_PADCONF_CAM_XCLKB 0x012E
+#define CONTROL_PADCONF_CAM_WEN 0x0130
+#define CONTROL_PADCONF_CAM_STROBE 0x0132
+#define CONTROL_PADCONF_CSI2_DX0 0x0134
+#define CONTROL_PADCONF_CSI2_DY0 0x0136
+#define CONTROL_PADCONF_CSI2_DX1 0x0138
+#define CONTROL_PADCONF_CSI2_DY1 0x013A
+/*Audio Interface */
+#define CONTROL_PADCONF_MCBSP2_FSX 0x013C
+#define CONTROL_PADCONF_MCBSP2_CLKX 0x013E
+#define CONTROL_PADCONF_MCBSP2_DR 0x0140
+#define CONTROL_PADCONF_MCBSP2_DX 0x0142
+#define CONTROL_PADCONF_MMC1_CLK 0x0144
+#define CONTROL_PADCONF_MMC1_CMD 0x0146
+#define CONTROL_PADCONF_MMC1_DAT0 0x0148
+#define CONTROL_PADCONF_MMC1_DAT1 0x014A
+#define CONTROL_PADCONF_MMC1_DAT2 0x014C
+#define CONTROL_PADCONF_MMC1_DAT3 0x014E
+#define CONTROL_PADCONF_MMC1_DAT4 0x0150
+#define CONTROL_PADCONF_MMC1_DAT5 0x0152
+#define CONTROL_PADCONF_MMC1_DAT6 0x0154
+#define CONTROL_PADCONF_MMC1_DAT7 0x0156
+/*Wireless LAN */
+#define CONTROL_PADCONF_MMC2_CLK 0x0158
+#define CONTROL_PADCONF_MMC2_CMD 0x015A
+#define CONTROL_PADCONF_MMC2_DAT0 0x015C
+#define CONTROL_PADCONF_MMC2_DAT1 0x015E
+#define CONTROL_PADCONF_MMC2_DAT2 0x0160
+#define CONTROL_PADCONF_MMC2_DAT3 0x0162
+#define CONTROL_PADCONF_MMC2_DAT4 0x0164
+#define CONTROL_PADCONF_MMC2_DAT5 0x0166
+#define CONTROL_PADCONF_MMC2_DAT6 0x0168
+#define CONTROL_PADCONF_MMC2_DAT7 0x016A
+/*Bluetooth*/
+#define CONTROL_PADCONF_MCBSP3_DX 0x016C
+#define CONTROL_PADCONF_MCBSP3_DR 0x016E
+#define CONTROL_PADCONF_MCBSP3_CLKX 0x0170
+#define CONTROL_PADCONF_MCBSP3_FSX 0x0172
+#define CONTROL_PADCONF_UART2_CTS 0x0174
+#define CONTROL_PADCONF_UART2_RTS 0x0176
+#define CONTROL_PADCONF_UART2_TX 0x0178
+#define CONTROL_PADCONF_UART2_RX 0x017A
+/*Modem Interface */
+#define CONTROL_PADCONF_UART1_TX 0x017C
+#define CONTROL_PADCONF_UART1_RTS 0x017E
+#define CONTROL_PADCONF_UART1_CTS 0x0180
+#define CONTROL_PADCONF_UART1_RX 0x0182
+#define CONTROL_PADCONF_MCBSP4_CLKX 0x0184
+#define CONTROL_PADCONF_MCBSP4_DR 0x0186
+#define CONTROL_PADCONF_MCBSP4_DX 0x0188
+#define CONTROL_PADCONF_MCBSP4_FSX 0x018A
+#define CONTROL_PADCONF_MCBSP1_CLKR 0x018C
+#define CONTROL_PADCONF_MCBSP1_FSR 0x018E
+#define CONTROL_PADCONF_MCBSP1_DX 0x0190
+#define CONTROL_PADCONF_MCBSP1_DR 0x0192
+#define CONTROL_PADCONF_MCBSP_CLKS 0x0194
+#define CONTROL_PADCONF_MCBSP1_FSX 0x0196
+#define CONTROL_PADCONF_MCBSP1_CLKX 0x0198
+/*Serial Interface*/
+#define CONTROL_PADCONF_UART3_CTS_RCTX 0x019A
+#define CONTROL_PADCONF_UART3_RTS_SD 0x019C
+#define CONTROL_PADCONF_UART3_RX_IRRX 0x019E
+#define CONTROL_PADCONF_UART3_TX_IRTX 0x01A0
+#define CONTROL_PADCONF_HSUSB0_CLK 0x01A2
+#define CONTROL_PADCONF_HSUSB0_STP 0x01A4
+#define CONTROL_PADCONF_HSUSB0_DIR 0x01A6
+#define CONTROL_PADCONF_HSUSB0_NXT 0x01A8
+#define CONTROL_PADCONF_HSUSB0_DATA0 0x01AA
+#define CONTROL_PADCONF_HSUSB0_DATA1 0x01AC
+#define CONTROL_PADCONF_HSUSB0_DATA2 0x01AE
+#define CONTROL_PADCONF_HSUSB0_DATA3 0x01B0
+#define CONTROL_PADCONF_HSUSB0_DATA4 0x01B2
+#define CONTROL_PADCONF_HSUSB0_DATA5 0x01B4
+#define CONTROL_PADCONF_HSUSB0_DATA6 0x01B6
+#define CONTROL_PADCONF_HSUSB0_DATA7 0x01B8
+#define CONTROL_PADCONF_I2C1_SCL 0x01BA
+#define CONTROL_PADCONF_I2C1_SDA 0x01BC
+#define CONTROL_PADCONF_I2C2_SCL 0x01BE
+#define CONTROL_PADCONF_I2C2_SDA 0x01C0
+#define CONTROL_PADCONF_I2C3_SCL 0x01C2
+#define CONTROL_PADCONF_I2C3_SDA 0x01C4
+#define CONTROL_PADCONF_I2C4_SCL 0x0A00
+#define CONTROL_PADCONF_I2C4_SDA 0x0A02
+#define CONTROL_PADCONF_HDQ_SIO 0x01C6
+#define CONTROL_PADCONF_MCSPI1_CLK 0x01C8
+#define CONTROL_PADCONF_MCSPI1_SIMO 0x01CA
+#define CONTROL_PADCONF_MCSPI1_SOMI 0x01CC
+#define CONTROL_PADCONF_MCSPI1_CS0 0x01CE
+#define CONTROL_PADCONF_MCSPI1_CS1 0x01D0
+#define CONTROL_PADCONF_MCSPI1_CS2 0x01D2
+#define CONTROL_PADCONF_MCSPI1_CS3 0x01D4
+#define CONTROL_PADCONF_MCSPI2_CLK 0x01D6
+#define CONTROL_PADCONF_MCSPI2_SIMO 0x01D8
+#define CONTROL_PADCONF_MCSPI2_SOMI 0x01DA
+#define CONTROL_PADCONF_MCSPI2_CS0 0x01DC
+#define CONTROL_PADCONF_MCSPI2_CS1 0x01DE
+/*Control and debug */
+#define CONTROL_PADCONF_SYS_32K 0x0A04
+#define CONTROL_PADCONF_SYS_CLKREQ 0x0A06
+#define CONTROL_PADCONF_SYS_NIRQ 0x01E0
+#define CONTROL_PADCONF_SYS_BOOT0 0x0A0A
+#define CONTROL_PADCONF_SYS_BOOT1 0x0A0C
+#define CONTROL_PADCONF_SYS_BOOT2 0x0A0E
+#define CONTROL_PADCONF_SYS_BOOT3 0x0A10
+#define CONTROL_PADCONF_SYS_BOOT4 0x0A12
+#define CONTROL_PADCONF_SYS_BOOT5 0x0A14
+#define CONTROL_PADCONF_SYS_BOOT6 0x0A16
+#define CONTROL_PADCONF_SYS_OFF_MODE 0x0A18
+#define CONTROL_PADCONF_SYS_CLKOUT1 0x0A1A
+#define CONTROL_PADCONF_SYS_CLKOUT2 0x01E2
+#define CONTROL_PADCONF_JTAG_nTRST 0x0A1C
+#define CONTROL_PADCONF_JTAG_TCK 0x0A1E
+#define CONTROL_PADCONF_JTAG_TMS 0x0A20
+#define CONTROL_PADCONF_JTAG_TDI 0x0A22
+#define CONTROL_PADCONF_JTAG_EMU0 0x0A24
+#define CONTROL_PADCONF_JTAG_EMU1 0x0A26
+#define CONTROL_PADCONF_ETK_CLK 0x0A28
+#define CONTROL_PADCONF_ETK_CTL 0x0A2A
+#define CONTROL_PADCONF_ETK_D0 0x0A2C
+#define CONTROL_PADCONF_ETK_D1 0x0A2E
+#define CONTROL_PADCONF_ETK_D2 0x0A30
+#define CONTROL_PADCONF_ETK_D3 0x0A32
+#define CONTROL_PADCONF_ETK_D4 0x0A34
+#define CONTROL_PADCONF_ETK_D5 0x0A36
+#define CONTROL_PADCONF_ETK_D6 0x0A38
+#define CONTROL_PADCONF_ETK_D7 0x0A3A
+#define CONTROL_PADCONF_ETK_D8 0x0A3C
+#define CONTROL_PADCONF_ETK_D9 0x0A3E
+#define CONTROL_PADCONF_ETK_D10 0x0A40
+#define CONTROL_PADCONF_ETK_D11 0x0A42
+#define CONTROL_PADCONF_ETK_D12 0x0A44
+#define CONTROL_PADCONF_ETK_D13 0x0A46
+#define CONTROL_PADCONF_ETK_D14 0x0A48
+#define CONTROL_PADCONF_ETK_D15 0x0A4A
+#define CONTROL_PADCONF_ETK_CLK_ES2 0x05D8
+#define CONTROL_PADCONF_ETK_CTL_ES2 0x05DA
+#define CONTROL_PADCONF_ETK_D0_ES2 0x05DC
+#define CONTROL_PADCONF_ETK_D1_ES2 0x05DE
+#define CONTROL_PADCONF_ETK_D2_ES2 0x05E0
+#define CONTROL_PADCONF_ETK_D3_ES2 0x05E2
+#define CONTROL_PADCONF_ETK_D4_ES2 0x05E4
+#define CONTROL_PADCONF_ETK_D5_ES2 0x05E6
+#define CONTROL_PADCONF_ETK_D6_ES2 0x05E8
+#define CONTROL_PADCONF_ETK_D7_ES2 0x05EA
+#define CONTROL_PADCONF_ETK_D8_ES2 0x05EC
+#define CONTROL_PADCONF_ETK_D9_ES2 0x05EE
+#define CONTROL_PADCONF_ETK_D10_ES2 0x05F0
+#define CONTROL_PADCONF_ETK_D11_ES2 0x05F2
+#define CONTROL_PADCONF_ETK_D12_ES2 0x05F4
+#define CONTROL_PADCONF_ETK_D13_ES2 0x05F6
+#define CONTROL_PADCONF_ETK_D14_ES2 0x05F8
+#define CONTROL_PADCONF_ETK_D15_ES2 0x05FA
+/*Die to Die */
+#define CONTROL_PADCONF_D2D_MCAD0 0x01E4
+#define CONTROL_PADCONF_D2D_MCAD1 0x01E6
+#define CONTROL_PADCONF_D2D_MCAD2 0x01E8
+#define CONTROL_PADCONF_D2D_MCAD3 0x01EA
+#define CONTROL_PADCONF_D2D_MCAD4 0x01EC
+#define CONTROL_PADCONF_D2D_MCAD5 0x01EE
+#define CONTROL_PADCONF_D2D_MCAD6 0x01F0
+#define CONTROL_PADCONF_D2D_MCAD7 0x01F2
+#define CONTROL_PADCONF_D2D_MCAD8 0x01F4
+#define CONTROL_PADCONF_D2D_MCAD9 0x01F6
+#define CONTROL_PADCONF_D2D_MCAD10 0x01F8
+#define CONTROL_PADCONF_D2D_MCAD11 0x01FA
+#define CONTROL_PADCONF_D2D_MCAD12 0x01FC
+#define CONTROL_PADCONF_D2D_MCAD13 0x01FE
+#define CONTROL_PADCONF_D2D_MCAD14 0x0200
+#define CONTROL_PADCONF_D2D_MCAD15 0x0202
+#define CONTROL_PADCONF_D2D_MCAD16 0x0204
+#define CONTROL_PADCONF_D2D_MCAD17 0x0206
+#define CONTROL_PADCONF_D2D_MCAD18 0x0208
+#define CONTROL_PADCONF_D2D_MCAD19 0x020A
+#define CONTROL_PADCONF_D2D_MCAD20 0x020C
+#define CONTROL_PADCONF_D2D_MCAD21 0x020E
+#define CONTROL_PADCONF_D2D_MCAD22 0x0210
+#define CONTROL_PADCONF_D2D_MCAD23 0x0212
+#define CONTROL_PADCONF_D2D_MCAD24 0x0214
+#define CONTROL_PADCONF_D2D_MCAD25 0x0216
+#define CONTROL_PADCONF_D2D_MCAD26 0x0218
+#define CONTROL_PADCONF_D2D_MCAD27 0x021A
+#define CONTROL_PADCONF_D2D_MCAD28 0x021C
+#define CONTROL_PADCONF_D2D_MCAD29 0x021E
+#define CONTROL_PADCONF_D2D_MCAD30 0x0220
+#define CONTROL_PADCONF_D2D_MCAD31 0x0222
+#define CONTROL_PADCONF_D2D_MCAD32 0x0224
+#define CONTROL_PADCONF_D2D_MCAD33 0x0226
+#define CONTROL_PADCONF_D2D_MCAD34 0x0228
+#define CONTROL_PADCONF_D2D_MCAD35 0x022A
+#define CONTROL_PADCONF_D2D_MCAD36 0x022C
+#define CONTROL_PADCONF_D2D_CLK26MI 0x022E
+#define CONTROL_PADCONF_D2D_NRESPWRON 0x0230
+#define CONTROL_PADCONF_D2D_NRESWARM 0x0232
+#define CONTROL_PADCONF_D2D_ARM9NIRQ 0x0234
+#define CONTROL_PADCONF_D2D_UMA2P6FIQ 0x0236
+#define CONTROL_PADCONF_D2D_SPINT 0x0238
+#define CONTROL_PADCONF_D2D_FRINT 0x023A
+#define CONTROL_PADCONF_D2D_DMAREQ0 0x023C
+#define CONTROL_PADCONF_D2D_DMAREQ1 0x023E
+#define CONTROL_PADCONF_D2D_DMAREQ2 0x0240
+#define CONTROL_PADCONF_D2D_DMAREQ3 0x0242
+#define CONTROL_PADCONF_D2D_N3GTRST 0x0244
+#define CONTROL_PADCONF_D2D_N3GTDI 0x0246
+#define CONTROL_PADCONF_D2D_N3GTDO 0x0248
+#define CONTROL_PADCONF_D2D_N3GTMS 0x024A
+#define CONTROL_PADCONF_D2D_N3GTCK 0x024C
+#define CONTROL_PADCONF_D2D_N3GRTCK 0x024E
+#define CONTROL_PADCONF_D2D_MSTDBY 0x0250
+#define CONTROL_PADCONF_D2D_SWAKEUP 0x0A4C
+#define CONTROL_PADCONF_D2D_IDLEREQ 0x0252
+#define CONTROL_PADCONF_D2D_IDLEACK 0x0254
+#define CONTROL_PADCONF_D2D_MWRITE 0x0256
+#define CONTROL_PADCONF_D2D_SWRITE 0x0258
+#define CONTROL_PADCONF_D2D_MREAD 0x025A
+#define CONTROL_PADCONF_D2D_SREAD 0x025C
+#define CONTROL_PADCONF_D2D_MBUSFLAG 0x025E
+#define CONTROL_PADCONF_D2D_SBUSFLAG 0x0260
+#define CONTROL_PADCONF_SDRC_CKE0 0x0262
+#define CONTROL_PADCONF_SDRC_CKE1 0x0264
+
+#define MUX_VAL(OFFSET,VALUE)\
+ writew((VALUE), OMAP34XX_CTRL_BASE + (OFFSET));
+
+#define CP(x) (CONTROL_PADCONF_##x)
+
+#endif
--- /dev/null
+/*
+ * (C) Copyright 2006-2008
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <x0khasim@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _OMAP3_H_
+#define _OMAP3_H_
+
+/* Stuff on L3 Interconnect */
+#define SMX_APE_BASE 0x68000000
+
+/* GPMC */
+#define OMAP34XX_GPMC_BASE 0x6E000000
+
+/* SMS */
+#define OMAP34XX_SMS_BASE 0x6C000000
+
+/* SDRC */
+#define OMAP34XX_SDRC_BASE 0x6D000000
+
+/*
+ * L4 Peripherals - L4 Wakeup and L4 Core now
+ */
+#define OMAP34XX_CORE_L4_IO_BASE 0x48000000
+#define OMAP34XX_WAKEUP_L4_IO_BASE 0x48300000
+#define OMAP34XX_L4_PER 0x49000000
+#define OMAP34XX_L4_IO_BASE OMAP34XX_CORE_L4_IO_BASE
+
+/* CONTROL */
+#define OMAP34XX_CTRL_BASE (OMAP34XX_L4_IO_BASE + 0x2000)
+
+/* UART */
+#define OMAP34XX_UART1 (OMAP34XX_L4_IO_BASE + 0x6a000)
+#define OMAP34XX_UART2 (OMAP34XX_L4_IO_BASE + 0x6c000)
+#define OMAP34XX_UART3 (OMAP34XX_L4_PER + 0x20000)
+
+/* General Purpose Timers */
+#define OMAP34XX_GPT1 0x48318000
+#define OMAP34XX_GPT2 0x49032000
+#define OMAP34XX_GPT3 0x49034000
+#define OMAP34XX_GPT4 0x49036000
+#define OMAP34XX_GPT5 0x49038000
+#define OMAP34XX_GPT6 0x4903A000
+#define OMAP34XX_GPT7 0x4903C000
+#define OMAP34XX_GPT8 0x4903E000
+#define OMAP34XX_GPT9 0x49040000
+#define OMAP34XX_GPT10 0x48086000
+#define OMAP34XX_GPT11 0x48088000
+#define OMAP34XX_GPT12 0x48304000
+
+/* WatchDog Timers (1 secure, 3 GP) */
+#define WD1_BASE 0x4830C000
+#define WD2_BASE 0x48314000
+#define WD3_BASE 0x49030000
+
+/* 32KTIMER */
+#define SYNC_32KTIMER_BASE 0x48320000
+
+#ifndef __ASSEMBLY__
+
+typedef struct s32ktimer {
+ unsigned char res[0x10];
+ unsigned int s32k_cr; /* 0x10 */
+} s32ktimer_t;
+
+#endif /* __ASSEMBLY__ */
+
+/* OMAP3 GPIO registers */
+#define OMAP34XX_GPIO1_BASE 0x48310000
+#define OMAP34XX_GPIO2_BASE 0x49050000
+#define OMAP34XX_GPIO3_BASE 0x49052000
+#define OMAP34XX_GPIO4_BASE 0x49054000
+#define OMAP34XX_GPIO5_BASE 0x49056000
+#define OMAP34XX_GPIO6_BASE 0x49058000
+
+#ifndef __ASSEMBLY__
+typedef struct gpio {
+ unsigned char res1[0x34];
+ unsigned int oe; /* 0x34 */
+ unsigned char res2[0x58];
+ unsigned int cleardataout; /* 0x90 */
+ unsigned int setdataout; /* 0x94 */
+} gpio_t;
+#endif /* __ASSEMBLY__ */
+
+#define GPIO0 (0x1 << 0)
+#define GPIO1 (0x1 << 1)
+#define GPIO2 (0x1 << 2)
+#define GPIO3 (0x1 << 3)
+#define GPIO4 (0x1 << 4)
+#define GPIO5 (0x1 << 5)
+#define GPIO6 (0x1 << 6)
+#define GPIO7 (0x1 << 7)
+#define GPIO8 (0x1 << 8)
+#define GPIO9 (0x1 << 9)
+#define GPIO10 (0x1 << 10)
+#define GPIO11 (0x1 << 11)
+#define GPIO12 (0x1 << 12)
+#define GPIO13 (0x1 << 13)
+#define GPIO14 (0x1 << 14)
+#define GPIO15 (0x1 << 15)
+#define GPIO16 (0x1 << 16)
+#define GPIO17 (0x1 << 17)
+#define GPIO18 (0x1 << 18)
+#define GPIO19 (0x1 << 19)
+#define GPIO20 (0x1 << 20)
+#define GPIO21 (0x1 << 21)
+#define GPIO22 (0x1 << 22)
+#define GPIO23 (0x1 << 23)
+#define GPIO24 (0x1 << 24)
+#define GPIO25 (0x1 << 25)
+#define GPIO26 (0x1 << 26)
+#define GPIO27 (0x1 << 27)
+#define GPIO28 (0x1 << 28)
+#define GPIO29 (0x1 << 29)
+#define GPIO30 (0x1 << 30)
+#define GPIO31 (0x1 << 31)
+
+/* base address for indirect vectors (internal boot mode) */
+#define SRAM_OFFSET0 0x40000000
+#define SRAM_OFFSET1 0x00200000
+#define SRAM_OFFSET2 0x0000F800
+#define SRAM_VECT_CODE (SRAM_OFFSET0 | SRAM_OFFSET1 | \
+ SRAM_OFFSET2)
+
+#define LOW_LEVEL_SRAM_STACK 0x4020FFFC
+
+#define DEBUG_LED1 149 /* gpio */
+#define DEBUG_LED2 150 /* gpio */
+
+#define XDR_POP 5 /* package on package part */
+#define SDR_DISCRETE 4 /* 128M memory SDR module */
+#define DDR_STACKED 3 /* stacked part on 2422 */
+#define DDR_COMBO 2 /* combo part on cpu daughter card */
+#define DDR_DISCRETE 1 /* 2x16 parts on daughter card */
+
+#define DDR_100 100 /* type found on most mem d-boards */
+#define DDR_111 111 /* some combo parts */
+#define DDR_133 133 /* most combo, some mem d-boards */
+#define DDR_165 165 /* future parts */
+
+#define CPU_3430 0x3430
+
+/*
+ * 343x real hardware:
+ * ES1 = rev 0
+ *
+ * 343x code defines:
+ * ES1 = 0+1 = 1
+ * ES1 = 1+1 = 1
+ */
+#define CPU_3430_ES1 1
+#define CPU_3430_ES2 2
+
+#define WIDTH_8BIT 0x0000
+#define WIDTH_16BIT 0x1000 /* bit pos for 16 bit in gpmc */
+
+/* SDP definitions according to FPGA Rev. Is this OK?? */
+#define SDP_3430_V1 0x1
+#define SDP_3430_V2 0x2
+
+/* EVM definitions */
+#define OMAP3EVM_V1 0x1
+#define OMAP3EVM_V2 0x2
+
+/* I2C power management companion definitions */
+#define PWRMGT_ADDR_ID1 0x48
+#define PWRMGT_ADDR_ID2 0x49
+#define PWRMGT_ADDR_ID3 0x4A
+#define PWRMGT_ADDR_ID4 0x4B
+
+/* I2C ID3 (slave3) register */
+#define LEDEN 0xEE
+
+#define LEDAON (0x1 << 0)
+#define LEDBON (0x1 << 1)
+#define LEDAPWM (0x1 << 4)
+#define LEDBPWM (0x1 << 5)
+
+/* I2C ID4 (slave4) register */
+#define VAUX2_DEV_GRP 0x76
+#define VAUX2_DEDICATED 0x79
+#define VAUX3_DEV_GRP 0x7A
+#define VAUX3_DEDICATED 0x7D
+#define VPLL2_DEV_GRP 0x8E
+#define VPLL2_DEDICATED 0x91
+#define VDAC_DEV_GRP 0x96
+#define VDAC_DEDICATED 0x99
+
+#define DEV_GRP_P1 0x20
+#define DEV_GRP_ALL 0xE0
+
+#define VAUX2_VSEL_28 0x09
+#define VAUX3_VSEL_28 0x03
+#define VPLL2_VSEL_18 0x05
+#define VDAC_VSEL_18 0x03
+
+#endif
--- /dev/null
+/*
+ * (C) Copyright 2004-2008 Texas Instruments, <www.ti.com>
+ * Rohit Choraria <rohitkc@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef __ASM_ARCH_OMAP_GPMC_H
+#define __ASM_ARCH_OMAP_GPMC_H
+
+#define GPMC_BUF_EMPTY 0
+#define GPMC_BUF_FULL 1
+
+#define ECCCLEAR (0x1 << 8)
+#define ECCRESULTREG1 (0x1 << 0)
+#define ECCSIZE512BYTE 0xFF
+#define ECCSIZE1 (ECCSIZE512BYTE << 22)
+#define ECCSIZE0 (ECCSIZE512BYTE << 12)
+#define ECCSIZE0SEL (0x000 << 0)
+
+/* Generic ECC Layouts */
+/* Large Page x8 NAND device Layout */
+#ifdef GPMC_NAND_ECC_LP_x8_LAYOUT
+#define GPMC_NAND_HW_ECC_LAYOUT {\
+ .eccbytes = 12,\
+ .eccpos = {1, 2, 3, 4, 5, 6, 7, 8,\
+ 9, 10, 11, 12},\
+ .oobfree = {\
+ {.offset = 13,\
+ .length = 51 } } \
+}
+#endif
+
+/* Large Page x16 NAND device Layout */
+#ifdef GPMC_NAND_ECC_LP_x16_LAYOUT
+#define GPMC_NAND_HW_ECC_LAYOUT {\
+ .eccbytes = 12,\
+ .eccpos = {2, 3, 4, 5, 6, 7, 8, 9,\
+ 10, 11, 12, 13},\
+ .oobfree = {\
+ {.offset = 14,\
+ .length = 50 } } \
+}
+#endif
+
+/* Small Page x8 NAND device Layout */
+#ifdef GPMC_NAND_ECC_SP_x8_LAYOUT
+#define GPMC_NAND_HW_ECC_LAYOUT {\
+ .eccbytes = 3,\
+ .eccpos = {1, 2, 3},\
+ .oobfree = {\
+ {.offset = 4,\
+ .length = 12 } } \
+}
+#endif
+
+/* Small Page x16 NAND device Layout */
+#ifdef GPMC_NAND_ECC_SP_x16_LAYOUT
+#define GPMC_NAND_HW_ECC_LAYOUT {\
+ .eccbytes = 3,\
+ .eccpos = {2, 3, 4},\
+ .oobfree = {\
+ {.offset = 5,\
+ .length = 11 } } \
+}
+#endif
+
+#endif /* __ASM_ARCH_OMAP_GPMC_H */
+
--- /dev/null
+/*
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _SYS_PROTO_H_
+#define _SYS_PROTO_H_
+
+typedef struct {
+ u32 board_type_v1;
+ u32 board_type_v2;
+ u32 mtype;
+ char *cpu_string;
+ char *board_string;
+ char *nand_string;
+} omap3_sysinfo;
+
+void prcm_init(void);
+void per_clocks_enable(void);
+
+void memif_init(void);
+void sdrc_init(void);
+void do_sdrc_init(u32, u32);
+void gpmc_init(void);
+
+void watchdog_init(void);
+void set_muxconf_regs(void);
+
+u32 get_cpu_rev(void);
+u32 get_mem_type(void);
+u32 get_sysboot_value(void);
+u32 is_gpmc_muxed(void);
+u32 get_gpmc0_type(void);
+u32 get_gpmc0_width(void);
+u32 get_board_type(void);
+void display_board_info(u32);
+u32 get_sdr_cs_size(u32);
+u32 get_sdr_cs_offset(u32);
+u32 is_running_in_sdram(void);
+u32 is_running_in_sram(void);
+u32 is_running_in_flash(void);
+u32 get_device_type(void);
+void l2cache_enable(void);
+void secureworld_exit(void);
+void setup_auxcr(void);
+void try_unlock_memory(void);
+u32 get_boot_type(void);
+void v7_flush_dcache_all(u32);
+void sr32(void *, u32, u32, u32);
+u32 wait_on_value(u32, u32, void *, u32);
+void sdelay(unsigned long);
+void make_cs1_contiguous(void);
+void omap_nand_switch_ecc(int);
+void power_init_r(void);
+
+#endif
#include <configs/omap1510.h>
#define CONFIG_BOOTARGS "mem=16M console=ttyS0,115200n8 root=/dev/mtdblock3 rw"
+#ifdef CONFIG_STDOUT_USBTTY
#define CONFIG_PREBOOT "setenv stdout usbtty;setenv stdin usbtty"
+#endif
/*
* Miscellaneous configurable options
/*-----------------------------------------------------------------------
* FLASH and environment organization
+ * V1
+ * PHYS_FLASH_SIZE_1 (16 << 10) 16 MB
+ * PHYS_FLASH_SIZE_2 (8 << 10) 8 MB
+ * V2 only 1 flash
+ * PHYS_FLASH_SIZE_1 (32 << 10) 32 MB
*/
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define PHYS_FLASH_SIZE (16 << 10) /* 16 MB */
#define PHYS_FLASH_SECT_SIZE (128*1024) /* Size of a sector (128kB) */
-#define CONFIG_SYS_MAX_FLASH_SECT (128) /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_SECT (256) /* max number of sectors on one chip */
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + PHYS_FLASH_SECT_SIZE) /* addr of environment */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* Monitor at beginning of flash */
#define CONFIG_SYS_MONITOR_LEN PHYS_FLASH_SECT_SIZE /* Reserve 1 sector */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE + PHYS_FLASH_SIZE }
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, PHYS_FLASH_2 }
/*-----------------------------------------------------------------------
* FLASH driver setup
--- /dev/null
+/*
+ * (C) Copyright 2005
+ * STMicroelectronics.
+ * Configuration settings for the STn8815 nomadik board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_ARM926EJS
+#define CONFIG_NOMADIK
+#define CONFIG_NOMADIK_8815
+#define CONFIG_NOMADIK_NDK15
+#define CONFIG_NOMADIK_NHK15
+
+#define CONFIG_SKIP_LOWLEVEL_INIT /* we have already been loaded to RAM */
+
+/* commands */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+/* At this point there is no flash driver, so remove some commands */
+#undef CONFIG_CMD_ENV
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_IMLS
+
+/* user interface */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT "Nomadik> "
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg Buffer Size */
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_LOAD_ADDR 0x800000 /* default load address */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE
+
+/* boot config */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_BOOTDELAY 1
+#define CONFIG_BOOTARGS "root=/dev/ram0 console=ttyAMA1,115200n8 init=linuxrc"
+#define CONFIG_BOOTCOMMAND "fsload 0x100000 kernel.uimg;" \
+ " fsload 0x800000 initrd.gz.uimg;" \
+ " bootm 0x100000 0x800000"
+
+/* memory-related information */
+#define CONFIG_NR_DRAM_BANKS 2
+#define PHYS_SDRAM_1 0x00000000 /* DDR-SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */
+#define PHYS_SDRAM_2 0x08000000 /* SDR-SDRAM BANK #2*/
+#define PHYS_SDRAM_2_SIZE 0x04000000 /* 64 MB */
+
+#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
+#ifdef CONFIG_USE_IRQ
+# define CONFIG_STACKSIZE_IRQ (4 * 1024) /* IRQ stack */
+# define CONFIG_STACKSIZE_FIQ (4 * 1024) /* FIQ stack */
+#endif
+
+#define CONFIG_SYS_MEMTEST_START 0x00000000
+#define CONFIG_SYS_MEMTEST_END 0x0FFFFFFF
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256 * 1024)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* for initial data */
+
+#define CONFIG_MISC_INIT_R /* call misc_init_r during start up */
+
+/* timing informazion */
+#define CONFIG_SYS_HZ (2400000 / 256) /* Timer0: 2.4Mhz + divider */
+#define CONFIG_SYS_TIMERBASE 0x101E2000
+#undef CONFIG_SYS_CLKS_IN_HZ
+
+/* serial port (PL011) configuration */
+#define CONFIG_PL011_SERIAL
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CFG_SERIAL0 0x101FD000
+#define CFG_SERIAL1 0x101FB000
+
+#define CONFIG_PL01x_PORTS { (void *)CFG_SERIAL0, (void *)CFG_SERIAL1 }
+#define CONFIG_PL011_CLOCK 48000000
+
+/* Ethernet */
+#define PCI_MEMORY_VADDR 0xe8000000
+#define PCI_IO_VADDR 0xee000000
+#define __io(a) ((void __iomem *)(PCI_IO_VADDR + (a)))
+#define __mem_isa(a) ((a) + PCI_MEMORY_VADDR)
+
+#define CONFIG_DRIVER_SMC91111 /* Using SMC91c111*/
+#define CONFIG_SMC91111_BASE 0x34000300
+#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */
+#define CONFIG_SMC_USE_32_BIT
+#define CONFIG_BOOTFILE "uImage"
+
+/* flash memory and filesystem information */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_MTD_ONENAND_VERIFY_WRITE
+#define CONFIG_SYS_ONENAND_BASE 0x30000000
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0x40000000
+
+#define CONFIG_SYS_NO_FLASH
+
+#ifdef CONFIG_BOOT_ONENAND
+
+# undef CONFIG_CMD_NAND /* Temporary: nand and onenand can't coexist */
+ /* Partition Size Start
+ * XloaderTOC + X-Loader 256KB 0x00000000
+ * Memory init function 256KB 0x00040000
+ * U-Boot 2MB 0x00080000
+ * Sysimage (kernel + ramdisk) 4MB 0x00280000
+ * JFFS2 Root filesystem 22MB 0x00680000
+ * JFFS2 User Data 227.5MB 0x01C80000
+ */
+# define CONFIG_JFFS2_PART_SIZE 0x400000
+# define CONFIG_JFFS2_PART_OFFSET 0x280000
+
+# define CONFIG_ENV_IS_IN_ONENAND
+# define CONFIG_ENV_SIZE (256 * 1024)
+# define CONFIG_ENV_ADDR 0x30300000
+
+#else /* ! CONFIG_BOOT_ONENAND */
+
+# undef CONFIG_CMD_ONENAND /* Temporary: nand and onenand can't coexist */
+
+# define CONFIG_JFFS2_DEV "nand0"
+# define CONFIG_JFFS2_NAND 1 /* For the jffs2 support*/
+# define CONFIG_JFFS2_PART_SIZE 0x00300000
+# define CONFIG_JFFS2_PART_OFFSET 0x00280000
+
+# define CONFIG_ENV_IS_IN_NAND
+# define CONFIG_ENV_SIZE 0x20000 /*128 Kb*/
+# define CONFIG_ENV_OFFSET (0x8000000 - CONFIG_ENV_SIZE)
+
+#endif /* CONFIG_BOOT_ONENAND */
+
+/* Temporarily, until we have no driver, env is not in nand */
+#undef CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_IS_NOWHERE
+
+/* this is needed to make hello_world.c and other stuff happy */
+#define CONFIG_SYS_MAX_FLASH_SECT 512
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+
+/* base addresses of our peripherals */
+#define NOMADIK_SRC_BASE 0x101E0000 /* System and Reset Cnt */
+#define NOMADIK_PMU_BASE 0x101E9000 /* Power Management Unit */
+#define NOMADIK_MPMC_BASE 0x10110000 /* SDRAM Controller */
+#define NOMADIK_FSMC_BASE 0x10100000 /* FSMC Controller */
+#define NOMADIK_1NAND_BASE 0x30000000
+#define NOMADIK_GPIO0_BASE 0x101E4000
+#define NOMADIK_GPIO1_BASE 0x101E5000
+#define NOMADIK_GPIO2_BASE 0x101E6000
+#define NOMADIK_GPIO3_BASE 0x101E7000
+#define NOMADIK_CPLD_BASE 0x36000000
+#define NOMADIK_UART0_BASE 0x101FD000
+#define NOMADIK_UART1_BASE 0x101FB000
+#define NOMADIK_UART2_BASE 0x101F2000
+
+#define NOMADIK_I2C1_BASE 0x101F7000 /* I2C1 interface */
+#define NOMADIK_I2C0_BASE 0x101F8000 /* I2C0 interface */
+
+#define NOMADIK_RTC_BASE 0x101E8000
+#define NOMADIK_ETH0_BASE 0x36800300
+#define NOMADIK_CPLD_UART_BASE 0x36480000
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2006-2008
+ * Texas Instruments.
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <x0khasim@ti.com>
+ *
+ * Configuration settings for the TI OMAP3530 Beagle board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_ARMCORTEXA8 1 /* This is an ARM V7 CPU core */
+#define CONFIG_OMAP 1 /* in a TI OMAP core */
+#define CONFIG_OMAP34XX 1 /* which is a 34XX */
+#define CONFIG_OMAP3430 1 /* which is in a 3430 */
+#define CONFIG_OMAP3_BEAGLE 1 /* working with BEAGLE */
+
+#include <asm/arch/cpu.h> /* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+/* Clock Defines */
+#define V_OSCK 26000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK >> 1)
+
+#undef CONFIG_USE_IRQ /* no support for IRQs */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG 1
+#define CONFIG_REVISION_TAG 1
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+ /* Sector */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
+ /* initial data */
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX 3
+#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
+#define CONFIG_SERIAL3 3 /* UART3 on Beagle Rev 2 */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
+ 115200}
+#define CONFIG_MMC 1
+#define CONFIG_OMAP3_MMC 1
+#define CONFIG_DOS_PARTITION 1
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EXT2 /* EXT2 Support */
+#define CONFIG_CMD_FAT /* FAT support */
+#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
+
+#define CONFIG_CMD_I2C /* I2C serial bus support */
+#define CONFIG_CMD_MMC /* MMC support */
+#define CONFIG_CMD_NAND /* NAND support */
+
+#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
+#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
+#undef CONFIG_CMD_IMI /* iminfo */
+#undef CONFIG_CMD_IMLS /* List all found images */
+#undef CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
+#undef CONFIG_CMD_NFS /* NFS support */
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_BUS 0
+#define CONFIG_SYS_I2C_BUS_SELECT 1
+#define CONFIG_DRIVER_OMAP34XX_I2C 1
+
+/*
+ * Board NAND Info.
+ */
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
+ /* to access nand */
+#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
+ /* to access nand at */
+ /* CS0 */
+#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
+
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
+ /* devices */
+#define SECTORSIZE 512
+
+#define NAND_ALLOW_ERASE_ALL
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+#define NAND_NO_RB 1
+#define CONFIG_SYS_NAND_WP
+
+#define CONFIG_JFFS2_NAND
+/* nand device jffs2 lives on */
+#define CONFIG_JFFS2_DEV "nand0"
+/* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_OFFSET 0x680000
+#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* size of jffs2 */
+ /* partition */
+
+/* Environment information */
+#define CONFIG_BOOTDELAY 10
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=0x82000000\0" \
+ "console=ttyS2,115200n8\0" \
+ "videomode=1024x768@60,vxres=1024,vyres=768\0" \
+ "videospec=omapfb:vram:2M,vram:4M\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "video=${videospec},mode:${videomode} " \
+ "root=/dev/mmcblk0p2 rw " \
+ "rootfstype=ext3 rootwait\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "video=${videospec},mode:${videomode} " \
+ "root=/dev/mtdblock4 rw " \
+ "rootfstype=jffs2\0" \
+ "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "autoscr ${loadaddr}\0" \
+ "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "bootm ${loadaddr}\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${loadaddr} 280000 400000; " \
+ "bootm ${loadaddr}\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmcinit; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run nandboot; " \
+ "fi; " \
+ "fi; " \
+ "else run nandboot; fi"
+
+#define CONFIG_AUTO_COMPLETE 1
+/*
+ * Miscellaneous configurable options
+ */
+#define V_PROMPT "OMAP3 beagleboard.org # "
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_PROMPT V_PROMPT
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
+
+#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) /* memtest */
+ /* works on */
+#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
+ 0x01F00000) /* 31MB */
+
+#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
+
+#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */
+ /* load address */
+
+/*
+ * 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
+ * 32KHz clk, or from external sig. This rate is divided by a local divisor.
+ */
+#define V_PVT 7
+
+#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
+#define CONFIG_SYS_PVT V_PVT /* 2^(pvt+1) */
+#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PVT))
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE SZ_128K /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
+#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
+#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
+
+/* SDRAM Bank Allocation method */
+#define SDRC_R_B_C 1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+
+/* **** PISMO SUPPORT *** */
+
+/* Configure the PISMO */
+#define PISMO1_NAND_SIZE GPMC_SIZE_128M
+#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
+
+#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
+ /* one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
+#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+
+#define CONFIG_SYS_FLASH_BASE boot_flash_base
+
+/* Monitor at start of flash */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
+
+#define CONFIG_ENV_IS_IN_NAND 1
+#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
+#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
+
+#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
+#define CONFIG_ENV_OFFSET boot_flash_off
+#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+
+/*-----------------------------------------------------------------------
+ * CFI FLASH driver setup
+ */
+/* timeout values are in ticks */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
+
+/* Flash banks JFFS2 should use */
+#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
+ CONFIG_SYS_MAX_NAND_DEVICE)
+#define CONFIG_SYS_JFFS2_MEM_NAND
+/* use flash_info[2] */
+#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+#ifndef __ASSEMBLY__
+extern gpmc_csx_t *nand_cs_base;
+extern gpmc_t *gpmc_cfg_base;
+extern unsigned int boot_flash_base;
+extern volatile unsigned int boot_flash_env_addr;
+extern unsigned int boot_flash_off;
+extern unsigned int boot_flash_sec;
+extern unsigned int boot_flash_type;
+#endif
+
+
+#define WRITE_NAND_COMMAND(d, adr)\
+ writel(d, &nand_cs_base->nand_cmd)
+#define WRITE_NAND_ADDRESS(d, adr)\
+ writel(d, &nand_cs_base->nand_adr)
+#define WRITE_NAND(d, adr) writew(d, &nand_cs_base->nand_dat)
+#define READ_NAND(adr) readl(&nand_cs_base->nand_dat)
+
+/* Other NAND Access APIs */
+#define NAND_WP_OFF() do {readl(&gpmc_cfg_base->config) |= GPMC_CONFIG_WP; } \
+ while (0)
+#define NAND_WP_ON() do {readl(&gpmc_cfg_base->config) &= ~GPMC_CONFIG_WP; } \
+ while (0)
+#define NAND_DISABLE_CE(nand)
+#define NAND_ENABLE_CE(nand)
+#define NAND_WAIT_READY(nand) udelay(10)
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2006-2008
+ * Texas Instruments.
+ * Author :
+ * Manikandan Pillai <mani.pillai@ti.com>
+ * Derived from Beagle Board and 3430 SDP code by
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
+ *
+ * Manikandan Pillai <mani.pillai@ti.com>
+ *
+ * Configuration settings for the TI OMAP3 EVM board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_ARMCORTEXA8 1 /* This is an ARM V7 CPU core */
+#define CONFIG_OMAP 1 /* in a TI OMAP core */
+#define CONFIG_OMAP34XX 1 /* which is a 34XX */
+#define CONFIG_OMAP3430 1 /* which is in a 3430 */
+#define CONFIG_OMAP3_EVM 1 /* working with EVM */
+
+#include <asm/arch/cpu.h> /* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+/* Clock Defines */
+#define V_OSCK 26000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK >> 1)
+
+#undef CONFIG_USE_IRQ /* no support for IRQs */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG 1
+#define CONFIG_REVISION_TAG 1
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+ /* Sector */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
+ /* initial data */
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
+#define CONFIG_SERIAL1 1 /* UART1 on OMAP3 EVM */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
+ 115200}
+#define CONFIG_MMC 1
+#define CONFIG_OMAP3_MMC 1
+#define CONFIG_DOS_PARTITION 1
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EXT2 /* EXT2 Support */
+#define CONFIG_CMD_FAT /* FAT support */
+#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
+
+#define CONFIG_CMD_I2C /* I2C serial bus support */
+#define CONFIG_CMD_MMC /* MMC support */
+#define CONFIG_CMD_ONENAND /* ONENAND support */
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+
+#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
+#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
+#undef CONFIG_CMD_IMI /* iminfo */
+#undef CONFIG_CMD_IMLS /* List all found images */
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_BUS 0
+#define CONFIG_SYS_I2C_BUS_SELECT 1
+#define CONFIG_DRIVER_OMAP34XX_I2C 1
+
+/*
+ * Board NAND Info.
+ */
+#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
+ /* to access nand */
+#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
+ /* to access */
+ /* nand at CS0 */
+
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
+ /* NAND devices */
+#define SECTORSIZE 512
+
+#define NAND_ALLOW_ERASE_ALL
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+#define NAND_NO_RB 1
+#define CONFIG_SYS_NAND_WP
+
+#define CONFIG_JFFS2_NAND
+/* nand device jffs2 lives on */
+#define CONFIG_JFFS2_DEV "nand0"
+/* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_OFFSET 0x680000
+#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* sz of jffs2 part */
+
+/* Environment information */
+#define CONFIG_BOOTDELAY 10
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=0x82000000\0" \
+ "console=ttyS2,115200n8\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "root=/dev/mmcblk0p2 rw " \
+ "rootfstype=ext3 rootwait\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "root=/dev/mtdblock4 rw " \
+ "rootfstype=jffs2\0" \
+ "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "autoscr ${loadaddr}\0" \
+ "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "bootm ${loadaddr}\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "onenand read ${loadaddr} 280000 400000; " \
+ "bootm ${loadaddr}\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmcinit; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run nandboot; " \
+ "fi; " \
+ "fi; " \
+ "else run nandboot; fi"
+
+#define CONFIG_AUTO_COMPLETE 1
+/*
+ * Miscellaneous configurable options
+ */
+#define V_PROMPT "OMAP3_EVM # "
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_PROMPT V_PROMPT
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command */
+ /* args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
+#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
+ 0x01F00000) /* 31MB */
+
+#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, */
+ /* in Hz */
+
+#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
+ /* address */
+
+/*
+ * 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
+ * 32KHz clk, or from external sig. This rate is divided by a local divisor.
+ */
+#define V_PVT 7
+
+#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
+#define CONFIG_SYS_PVT V_PVT /* 2^(pvt+1) */
+#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PVT))
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE SZ_128K /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
+#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
+#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
+
+/* SDRAM Bank Allocation method */
+#define SDRC_R_B_C 1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+
+/* **** PISMO SUPPORT *** */
+
+/* Configure the PISMO */
+#define PISMO1_NAND_SIZE GPMC_SIZE_128M
+#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
+
+#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors */
+ /* on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
+#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+
+#define CONFIG_SYS_FLASH_BASE boot_flash_base
+
+/* Monitor at start of flash */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
+
+#define CONFIG_ENV_IS_IN_ONENAND 1
+#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
+#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
+
+#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
+#define CONFIG_ENV_OFFSET boot_flash_off
+#define CONFIG_ENV_ADDR boot_flash_env_addr
+
+/*-----------------------------------------------------------------------
+ * CFI FLASH driver setup
+ */
+/* timeout values are in ticks */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
+
+/* Flash banks JFFS2 should use */
+#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
+ CONFIG_SYS_MAX_NAND_DEVICE)
+#define CONFIG_SYS_JFFS2_MEM_NAND
+/* use flash_info[2] */
+#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+#ifndef __ASSEMBLY__
+extern gpmc_csx_t *nand_cs_base;
+extern gpmc_t *gpmc_cfg_base;
+extern unsigned int boot_flash_base;
+extern volatile unsigned int boot_flash_env_addr;
+extern unsigned int boot_flash_off;
+extern unsigned int boot_flash_sec;
+extern unsigned int boot_flash_type;
+#endif
+
+
+#define WRITE_NAND_COMMAND(d, adr)\
+ writel(d, &nand_cs_base->nand_cmd)
+#define WRITE_NAND_ADDRESS(d, adr)\
+ writel(d, &nand_cs_base->nand_adr)
+#define WRITE_NAND(d, adr) writew(d, &nand_cs_base->nand_dat)
+#define READ_NAND(adr) readl(&nand_cs_base->nand_dat)
+
+/* Other NAND Access APIs */
+#define NAND_WP_OFF() do {readl(&gpmc_cfg_base->config) |= GPMC_CONFIG_WP; } \
+ while (0)
+#define NAND_WP_ON() do {readl(&gpmc_cfg_base->config) &= ~GPMC_CONFIG_WP; } \
+ while (0)
+#define NAND_DISABLE_CE(nand)
+#define NAND_ENABLE_CE(nand)
+#define NAND_WAIT_READY(nand) udelay(10)
+
+/*----------------------------------------------------------------------------
+ * SMSC9115 Ethernet from SMSC9118 family
+ *----------------------------------------------------------------------------
+ */
+#if defined(CONFIG_CMD_NET)
+
+#define CONFIG_DRIVER_SMC911X
+#define CONFIG_DRIVER_SMC911X_32_BIT
+#define CONFIG_DRIVER_SMC911X_BASE 0x2C000000
+
+#endif /* (CONFIG_CMD_NET) */
+
+/*
+ * BOOTP fields
+ */
+
+#define CONFIG_BOOTP_SUBNETMASK 0x00000001
+#define CONFIG_BOOTP_GATEWAY 0x00000002
+#define CONFIG_BOOTP_HOSTNAME 0x00000004
+#define CONFIG_BOOTP_BOOTPATH 0x00000010
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * Configuration settings for the Gumstix Overo board.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_ARMCORTEXA8 1 /* This is an ARM V7 CPU core */
+#define CONFIG_OMAP 1 /* in a TI OMAP core */
+#define CONFIG_OMAP34XX 1 /* which is a 34XX */
+#define CONFIG_OMAP3430 1 /* which is in a 3430 */
+#define CONFIG_OMAP3_OVERO 1 /* working with overo */
+
+#include <asm/arch/cpu.h> /* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+/* Clock Defines */
+#define V_OSCK 26000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK >> 1)
+
+#undef CONFIG_USE_IRQ /* no support for IRQs */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG 1
+#define CONFIG_REVISION_TAG 1
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+ /* Sector */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
+ /* initial data */
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX 3
+#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
+#define CONFIG_SERIAL3 3
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, \
+ 115200}
+#define CONFIG_MMC 1
+#define CONFIG_OMAP3_MMC 1
+#define CONFIG_DOS_PARTITION 1
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EXT2 /* EXT2 Support */
+#define CONFIG_CMD_FAT /* FAT support */
+#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
+
+#define CONFIG_CMD_I2C /* I2C serial bus support */
+#define CONFIG_CMD_MMC /* MMC support */
+#define CONFIG_CMD_NAND /* NAND support */
+
+#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
+#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
+#undef CONFIG_CMD_IMI /* iminfo */
+#undef CONFIG_CMD_IMLS /* List all found images */
+#undef CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
+#undef CONFIG_CMD_NFS /* NFS support */
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_BUS 0
+#define CONFIG_SYS_I2C_BUS_SELECT 1
+#define CONFIG_DRIVER_OMAP34XX_I2C 1
+
+/*
+ * Board NAND Info.
+ */
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
+ /* to access nand */
+#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
+ /* to access nand */
+ /* at CS0 */
+#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
+
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
+ /* devices */
+#define SECTORSIZE 512
+
+#define NAND_ALLOW_ERASE_ALL
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+#define NAND_NO_RB 1
+#define CONFIG_SYS_NAND_WP
+
+#define CONFIG_JFFS2_NAND
+/* nand device jffs2 lives on */
+#define CONFIG_JFFS2_DEV "nand0"
+/* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_OFFSET 0x680000
+#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* size of jffs2 */
+ /* partition */
+
+/* Environment information */
+#define CONFIG_BOOTDELAY 5
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=0x82000000\0" \
+ "console=ttyS2,115200n8\0" \
+ "videomode=1024x768@60,vxres=1024,vyres=768\0" \
+ "videospec=omapfb:vram:2M,vram:4M\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "video=${videospec},mode:${videomode} " \
+ "root=/dev/mmcblk0p2 rw " \
+ "rootfstype=ext3 rootwait\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "video=${videospec},mode:${videomode} " \
+ "root=/dev/mtdblock4 rw " \
+ "rootfstype=jffs2\0" \
+ "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "autoscr ${loadaddr}\0" \
+ "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "bootm ${loadaddr}\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${loadaddr} 280000 400000; " \
+ "bootm ${loadaddr}\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmcinit; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run nandboot; " \
+ "fi; " \
+ "fi; " \
+ "else run nandboot; fi"
+
+#define CONFIG_AUTO_COMPLETE 1
+/*
+ * Miscellaneous configurable options
+ */
+#define V_PROMPT "Overo # "
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_PROMPT V_PROMPT
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command */
+ /* args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
+#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
+ 0x01F00000) /* 31MB */
+
+#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, */
+ /* in Hz */
+
+#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
+ /* address */
+
+/*
+ * 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
+ * 32KHz clk, or from external sig. This rate is divided by a local divisor.
+ */
+#define V_PVT 7
+
+#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
+#define CONFIG_SYS_PVT V_PVT /* 2^(pvt+1) */
+#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PVT))
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE SZ_128K /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
+#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
+#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
+
+/* SDRAM Bank Allocation method */
+#define SDRC_R_B_C 1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+
+/* **** PISMO SUPPORT *** */
+
+/* Configure the PISMO */
+#define PISMO1_NAND_SIZE GPMC_SIZE_128M
+#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
+
+#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
+ /* one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
+#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+
+#define CONFIG_SYS_FLASH_BASE boot_flash_base
+
+/* Monitor at start of flash */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
+
+#define CONFIG_ENV_IS_IN_NAND 1
+#define ONENAND_ENV_OFFSET 0x240000 /* environment starts here */
+#define SMNAND_ENV_OFFSET 0x240000 /* environment starts here */
+
+#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
+#define CONFIG_ENV_OFFSET boot_flash_off
+#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+
+/*-----------------------------------------------------------------------
+ * CFI FLASH driver setup
+ */
+/* timeout values are in ticks */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
+
+/* Flash banks JFFS2 should use */
+#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
+ CONFIG_SYS_MAX_NAND_DEVICE)
+#define CONFIG_SYS_JFFS2_MEM_NAND
+/* use flash_info[2] */
+#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+#ifndef __ASSEMBLY__
+extern gpmc_csx_t *nand_cs_base;
+extern gpmc_t *gpmc_cfg_base;
+extern unsigned int boot_flash_base;
+extern volatile unsigned int boot_flash_env_addr;
+extern unsigned int boot_flash_off;
+extern unsigned int boot_flash_sec;
+extern unsigned int boot_flash_type;
+#endif
+
+
+#define WRITE_NAND_COMMAND(d, adr)\
+ writel(d, &nand_cs_base->nand_cmd)
+#define WRITE_NAND_ADDRESS(d, adr)\
+ writel(d, &nand_cs_base->nand_adr)
+#define WRITE_NAND(d, adr) writew(d, &nand_cs_base->nand_dat)
+#define READ_NAND(adr) readl(&nand_cs_base->nand_dat)
+
+/* Other NAND Access APIs */
+#define NAND_WP_OFF() do {readl(&gpmc_cfg_base->config) |= GPMC_CONFIG_WP; } \
+ while (0)
+#define NAND_WP_ON() do {readl(&gpmc_cfg_base->config) &= ~GPMC_CONFIG_WP; } \
+ while (0)
+#define NAND_DISABLE_CE(nand)
+#define NAND_ENABLE_CE(nand)
+#define NAND_WAIT_READY(nand) udelay(10)
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2008
+ * Grazvydas Ignotas <notasas@gmail.com>
+ *
+ * Configuration settings for the OMAP3 Pandora.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_ARMCORTEXA8 1 /* This is an ARM V7 CPU core */
+#define CONFIG_OMAP 1 /* in a TI OMAP core */
+#define CONFIG_OMAP34XX 1 /* which is a 34XX */
+#define CONFIG_OMAP3430 1 /* which is in a 3430 */
+#define CONFIG_OMAP3_PANDORA 1 /* working with pandora */
+
+#include <asm/arch/cpu.h> /* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+/* Clock Defines */
+#define V_OSCK 26000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK >> 1)
+
+#undef CONFIG_USE_IRQ /* no support for IRQs */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG 1
+#define CONFIG_REVISION_TAG 1
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+ /* Sector */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
+ /* initial data */
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX 3
+#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
+#define CONFIG_SERIAL3 3
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, \
+ 115200}
+#define CONFIG_MMC 1
+#define CONFIG_OMAP3_MMC 1
+#define CONFIG_DOS_PARTITION 1
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EXT2 /* EXT2 Support */
+#define CONFIG_CMD_FAT /* FAT support */
+#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
+
+#define CONFIG_CMD_I2C /* I2C serial bus support */
+#define CONFIG_CMD_MMC /* MMC support */
+#define CONFIG_CMD_NAND /* NAND support */
+
+#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
+#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
+#undef CONFIG_CMD_IMI /* iminfo */
+#undef CONFIG_CMD_IMLS /* List all found images */
+#undef CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
+#undef CONFIG_CMD_NFS /* NFS support */
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_BUS 0
+#define CONFIG_SYS_I2C_BUS_SELECT 1
+#define CONFIG_DRIVER_OMAP34XX_I2C 1
+
+/*
+ * Board NAND Info.
+ */
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
+ /* to access nand */
+#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
+ /* to access nand */
+ /* at CS0 */
+#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
+
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
+ /* devices */
+#define SECTORSIZE 512
+
+#define NAND_ALLOW_ERASE_ALL
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+#define NAND_NO_RB 1
+#define CONFIG_SYS_NAND_WP
+
+#define CONFIG_JFFS2_NAND
+/* nand device jffs2 lives on */
+#define CONFIG_JFFS2_DEV "nand0"
+/* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_OFFSET 0x680000
+#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* size of jffs2 */
+ /* partition */
+
+/* Environment information */
+#define CONFIG_BOOTDELAY 1
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=0x82000000\0" \
+ "console=ttyS0,115200n8\0" \
+ "videospec=omapfb:vram:2M,vram:4M\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "video=${videospec} " \
+ "root=/dev/mmcblk0p2 rw " \
+ "rootfstype=ext3 rootwait\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "video=${videospec} " \
+ "root=/dev/mtdblock4 rw " \
+ "rootfstype=jffs2\0" \
+ "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "autoscr ${loadaddr}\0" \
+ "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "bootm ${loadaddr}\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${loadaddr} 280000 400000; " \
+ "bootm ${loadaddr}\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmcinit; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run nandboot; " \
+ "fi; " \
+ "fi; " \
+ "else run nandboot; fi"
+
+#define CONFIG_AUTO_COMPLETE 1
+/*
+ * Miscellaneous configurable options
+ */
+#define V_PROMPT "Pandora # "
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_PROMPT V_PROMPT
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command */
+ /* args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
+#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
+ 0x01F00000) /* 31MB */
+
+#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, */
+ /* in Hz */
+
+#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
+ /* address */
+
+/*
+ * 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
+ * 32KHz clk, or from external sig. This rate is divided by a local divisor.
+ */
+#define V_PVT 7
+
+#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
+#define CONFIG_SYS_PVT V_PVT /* 2^(pvt+1) */
+#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PVT))
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE SZ_128K /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
+#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
+#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
+
+/* SDRAM Bank Allocation method */
+#define SDRC_R_B_C 1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+
+/* **** PISMO SUPPORT *** */
+
+/* Configure the PISMO */
+#define PISMO1_NAND_SIZE GPMC_SIZE_128M
+#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
+
+#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
+ /* one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
+#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+
+#define CONFIG_SYS_FLASH_BASE boot_flash_base
+
+/* Monitor at start of flash */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
+
+#define CONFIG_ENV_IS_IN_NAND 1
+#define ONENAND_ENV_OFFSET 0x240000 /* environment starts here */
+#define SMNAND_ENV_OFFSET 0x240000 /* environment starts here */
+
+#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
+#define CONFIG_ENV_OFFSET boot_flash_off
+#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+
+/*-----------------------------------------------------------------------
+ * CFI FLASH driver setup
+ */
+/* timeout values are in ticks */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
+
+/* Flash banks JFFS2 should use */
+#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
+ CONFIG_SYS_MAX_NAND_DEVICE)
+#define CONFIG_SYS_JFFS2_MEM_NAND
+/* use flash_info[2] */
+#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+#ifndef __ASSEMBLY__
+extern gpmc_csx_t *nand_cs_base;
+extern gpmc_t *gpmc_cfg_base;
+extern unsigned int boot_flash_base;
+extern volatile unsigned int boot_flash_env_addr;
+extern unsigned int boot_flash_off;
+extern unsigned int boot_flash_sec;
+extern unsigned int boot_flash_type;
+#endif
+
+
+#define WRITE_NAND_COMMAND(d, adr)\
+ writel(d, &nand_cs_base->nand_cmd)
+#define WRITE_NAND_ADDRESS(d, adr)\
+ writel(d, &nand_cs_base->nand_adr)
+#define WRITE_NAND(d, adr) writew(d, &nand_cs_base->nand_dat)
+#define READ_NAND(adr) readl(&nand_cs_base->nand_dat)
+
+/* Other NAND Access APIs */
+#define NAND_WP_OFF() do {readl(&gpmc_cfg_base->config) |= GPMC_CONFIG_WP; } \
+ while (0)
+#define NAND_WP_ON() do {readl(&gpmc_cfg_base->config) &= ~GPMC_CONFIG_WP; } \
+ while (0)
+#define NAND_DISABLE_CE(nand)
+#define NAND_ENABLE_CE(nand)
+#define NAND_WAIT_READY(nand) udelay(10)
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2006-2008
+ * Texas Instruments.
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <x0khasim@ti.com>
+ * Nishanth Menon <nm@ti.com>
+ *
+ * Configuration settings for the TI OMAP3430 Zoom MDK board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_ARMCORTEXA8 1 /* This is an ARM V7 CPU core */
+#define CONFIG_OMAP 1 /* in a TI OMAP core */
+#define CONFIG_OMAP34XX 1 /* which is a 34XX */
+#define CONFIG_OMAP3430 1 /* which is in a 3430 */
+#define CONFIG_OMAP3_ZOOM1 1 /* working with Zoom MDK Rev1 */
+
+#include <asm/arch/cpu.h> /* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+/* Clock Defines */
+#define V_OSCK 26000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK >> 1)
+
+#undef CONFIG_USE_IRQ /* no support for IRQs */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG 1
+#define CONFIG_REVISION_TAG 1
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+ /* Sector */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
+ /* initial data */
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX 3
+#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
+#define CONFIG_SERIAL3 3 /* UART3 */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
+ 115200}
+#define CONFIG_MMC 1
+#define CONFIG_OMAP3_MMC 1
+#define CONFIG_DOS_PARTITION 1
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EXT2 /* EXT2 Support */
+#define CONFIG_CMD_FAT /* FAT support */
+#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
+
+#define CONFIG_CMD_I2C /* I2C serial bus support */
+#define CONFIG_CMD_MMC /* MMC support */
+#define CONFIG_CMD_NAND /* NAND support */
+
+#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
+#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
+#undef CONFIG_CMD_IMI /* iminfo */
+#undef CONFIG_CMD_IMLS /* List all found images */
+#undef CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
+#undef CONFIG_CMD_NFS /* NFS support */
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_BUS 0
+#define CONFIG_SYS_I2C_BUS_SELECT 1
+#define CONFIG_DRIVER_OMAP34XX_I2C 1
+
+/*
+ * Board NAND Info.
+ */
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
+ /* to access nand */
+#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
+ /* to access nand at */
+ /* CS0 */
+#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
+
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
+ /* devices */
+#define SECTORSIZE 512
+
+#define NAND_ALLOW_ERASE_ALL
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+#define NAND_NO_RB 1
+#define CONFIG_SYS_NAND_WP
+
+#define CONFIG_JFFS2_NAND
+/* nand device jffs2 lives on */
+#define CONFIG_JFFS2_DEV "nand0"
+/* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_OFFSET 0x680000
+#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* size of jffs2 */
+ /* partition */
+
+/* Environment information */
+#define CONFIG_BOOTDELAY 10
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=0x82000000\0" \
+ "console=ttyS2,115200n8\0" \
+ "videomode=1024x768@60,vxres=1024,vyres=768\0" \
+ "videospec=omapfb:vram:2M,vram:4M\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "video=${videospec},mode:${videomode} " \
+ "root=/dev/mmcblk0p2 rw " \
+ "rootfstype=ext3 rootwait\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "video=${videospec},mode:${videomode} " \
+ "root=/dev/mtdblock4 rw " \
+ "rootfstype=jffs2\0" \
+ "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "autoscr ${loadaddr}\0" \
+ "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "bootm ${loadaddr}\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${loadaddr} 280000 400000; " \
+ "bootm ${loadaddr}\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmcinit; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run nandboot; " \
+ "fi; " \
+ "fi; " \
+ "else run nandboot; fi"
+
+#define CONFIG_AUTO_COMPLETE 1
+/*
+ * Miscellaneous configurable options
+ */
+#define V_PROMPT "OMAP3 Zoom1# "
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_PROMPT V_PROMPT
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
+
+#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) /* memtest */
+ /* works on */
+#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
+ 0x01F00000) /* 31MB */
+
+#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
+
+#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */
+ /* load address */
+
+/*
+ * 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
+ * 32KHz clk, or from external sig. This rate is divided by a local divisor.
+ */
+#define V_PVT 7
+
+#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
+#define CONFIG_SYS_PVT V_PVT /* 2^(pvt+1) */
+#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PVT))
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE SZ_128K /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
+#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
+#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
+
+/* SDRAM Bank Allocation method */
+#define SDRC_R_B_C 1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+
+/* **** PISMO SUPPORT *** */
+
+/* Configure the PISMO */
+#define PISMO1_NAND_SIZE GPMC_SIZE_128M
+#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
+
+#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
+ /* one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
+#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+
+#define CONFIG_SYS_FLASH_BASE boot_flash_base
+
+/* Monitor at start of flash */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
+
+#define CONFIG_ENV_IS_IN_NAND 1
+#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
+#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
+
+#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
+#define CONFIG_ENV_OFFSET boot_flash_off
+#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+
+/*-----------------------------------------------------------------------
+ * CFI FLASH driver setup
+ */
+/* timeout values are in ticks */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
+
+/* Flash banks JFFS2 should use */
+#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
+ CONFIG_SYS_MAX_NAND_DEVICE)
+#define CONFIG_SYS_JFFS2_MEM_NAND
+/* use flash_info[2] */
+#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+#ifndef __ASSEMBLY__
+extern gpmc_csx_t *nand_cs_base;
+extern gpmc_t *gpmc_cfg_base;
+extern unsigned int boot_flash_base;
+extern volatile unsigned int boot_flash_env_addr;
+extern unsigned int boot_flash_off;
+extern unsigned int boot_flash_sec;
+extern unsigned int boot_flash_type;
+#endif
+
+
+#define WRITE_NAND_COMMAND(d, adr)\
+ writel(d, &nand_cs_base->nand_cmd)
+#define WRITE_NAND_ADDRESS(d, adr)\
+ writel(d, &nand_cs_base->nand_adr)
+#define WRITE_NAND(d, adr) writew(d, &nand_cs_base->nand_dat)
+#define READ_NAND(adr) readl(&nand_cs_base->nand_dat)
+
+/* Other NAND Access APIs */
+#define NAND_WP_OFF() do {readl(&gpmc_cfg_base->config) |= GPMC_CONFIG_WP; } \
+ while (0)
+#define NAND_WP_ON() do {readl(&gpmc_cfg_base->config) &= ~GPMC_CONFIG_WP; } \
+ while (0)
+#define NAND_DISABLE_CE(nand)
+#define NAND_ENABLE_CE(nand)
+#define NAND_WAIT_READY(nand) udelay(10)
+
+#endif /* __CONFIG_H */
projects / people / ms / u-boot.git / commitdiff
