select DM_KEYBOARD
select DM_SERIAL
select DM_USB
+ select OF_BOARD_SETUP
select OF_CONTROL
select OF_SEPARATE
select SPL_STACK_R if !MACH_SUN9I
void s_init(void)
{
-#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I_A23
- /* Magic (undocmented) value taken from boot0, without this DRAM
- * access gets messed up (seems cache related) */
+ /*
+ * Undocumented magic taken from boot0, without this DRAM
+ * access gets messed up (seems cache related).
+ * The boot0 sources describe this as: "config ema for cache sram"
+ */
+#if defined CONFIG_MACH_SUN6I
setbits_le32(SUNXI_SRAMC_BASE + 0x44, 0x1800);
+#elif defined CONFIG_MACH_SUN8I_A23
+ uint version;
+
+ /* Unlock sram version info reg, read it, relock */
+ setbits_le32(SUNXI_SRAMC_BASE + 0x24, (1 << 15));
+ version = readl(SUNXI_SRAMC_BASE + 0x24);
+ clrbits_le32(SUNXI_SRAMC_BASE + 0x24, (1 << 15));
+
+ if ((version & 0xffff0000) == 0x16500000)
+ setbits_le32(SUNXI_SRAMC_BASE + 0x44, 0x1800);
+ else /* 0x1661 ? */
+ setbits_le32(SUNXI_SRAMC_BASE + 0x44, 0xc0);
#endif
+
#if defined CONFIG_MACH_SUN6I || \
defined CONFIG_MACH_SUN7I || \
defined CONFIG_MACH_SUN8I
timer_init();
gpio_init();
i2c_init_board();
+ eth_init_board();
}
#ifdef CONFIG_SPL_BUILD
dcache_enable();
}
#endif
-
-#ifdef CONFIG_CMD_NET
-/*
- * Initializes on-chip ethernet controllers.
- * to override, implement board_eth_init()
- */
-int cpu_eth_init(bd_t *bis)
-{
- __maybe_unused int rc;
-
-#ifdef CONFIG_MACPWR
- gpio_request(CONFIG_MACPWR, "macpwr");
- gpio_direction_output(CONFIG_MACPWR, 1);
- mdelay(200);
-#endif
-
-#ifdef CONFIG_SUNXI_GMAC
- rc = sunxi_gmac_initialize(bis);
- if (rc < 0) {
- printf("sunxi: failed to initialize gmac\n");
- return rc;
- }
-#endif
-
- return 0;
-}
-#endif
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
+#include <asm/arch/prcm.h>
#include <asm/arch/sys_proto.h>
__weak void clock_init_sec(void)
return 0;
}
+
+/* These functions are shared between various SoCs so put them here. */
+#if defined CONFIG_SUNXI_GEN_SUN6I && !defined CONFIG_MACH_SUN9I
+int clock_twi_onoff(int port, int state)
+{
+ struct sunxi_ccm_reg *const ccm =
+ (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+
+ if (port == 5) {
+ if (state)
+ prcm_apb0_enable(
+ PRCM_APB0_GATE_PIO | PRCM_APB0_GATE_I2C);
+ else
+ prcm_apb0_disable(
+ PRCM_APB0_GATE_PIO | PRCM_APB0_GATE_I2C);
+ return 0;
+ }
+
+ /* set the apb clock gate and reset for twi */
+ if (state) {
+ setbits_le32(&ccm->apb2_gate,
+ CLK_GATE_OPEN << (APB2_GATE_TWI_SHIFT + port));
+ setbits_le32(&ccm->apb2_reset_cfg,
+ 1 << (APB2_RESET_TWI_SHIFT + port));
+ } else {
+ clrbits_le32(&ccm->apb2_reset_cfg,
+ 1 << (APB2_RESET_TWI_SHIFT + port));
+ clrbits_le32(&ccm->apb2_gate,
+ CLK_GATE_OPEN << (APB2_GATE_TWI_SHIFT + port));
+ }
+
+ return 0;
+}
+#endif
#endif
}
-int clock_twi_onoff(int port, int state)
-{
- struct sunxi_ccm_reg *const ccm =
- (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
-
- if (port == 5) {
- if (state)
- prcm_apb0_enable(
- PRCM_APB0_GATE_PIO | PRCM_APB0_GATE_I2C);
- else
- prcm_apb0_disable(
- PRCM_APB0_GATE_PIO | PRCM_APB0_GATE_I2C);
- return 0;
- }
-
- /* set the apb clock gate for twi */
- if (state)
- setbits_le32(&ccm->apb2_gate,
- CLK_GATE_OPEN << (APB2_GATE_TWI_SHIFT+port));
- else
- clrbits_le32(&ccm->apb2_gate,
- CLK_GATE_OPEN << (APB2_GATE_TWI_SHIFT+port));
-
- return 0;
-}
-
#ifdef CONFIG_SPL_BUILD
void clock_set_pll1(unsigned int clk)
{
setbits_le32(&ccm->apb1_gate,
CLK_GATE_OPEN << (APB1_GATE_TWI_SHIFT + port));
setbits_le32(&ccm->apb1_reset_cfg,
- 1 << (APB1_RESET_UART_SHIFT + port));
+ 1 << (APB1_RESET_TWI_SHIFT + port));
} else {
clrbits_le32(&ccm->apb1_reset_cfg,
- 1 << (APB1_RESET_UART_SHIFT + port));
+ 1 << (APB1_RESET_TWI_SHIFT + port));
clrbits_le32(&ccm->apb1_gate,
CLK_GATE_OPEN << (APB1_GATE_TWI_SHIFT + port));
}
writel(0x94be6fa3, MCTL_PROTECT);
udelay(100);
- clrsetbits_le32(MX_UPD2, 0xfff << 16, 0x50 << 26);
+ clrsetbits_le32(MX_UPD2, 0xfff << 16, 0x50 << 16);
writel(0x0, MCTL_PROTECT);
udelay(100);
case 0: return sunxi_name_to_gpio(CONFIG_USB0_VBUS_PIN);
case 1: return sunxi_name_to_gpio(CONFIG_USB1_VBUS_PIN);
case 2: return sunxi_name_to_gpio(CONFIG_USB2_VBUS_PIN);
+ case 3: return sunxi_name_to_gpio(CONFIG_USB3_VBUS_PIN);
}
return -EINVAL;
}
sun4i-a10-ba10-tvbox.dtb \
sun4i-a10-chuwi-v7-cw0825.dtb \
sun4i-a10-cubieboard.dtb \
+ sun4i-a10-dserve-dsrv9703c.dtb \
sun4i-a10-gemei-g9.dtb \
sun4i-a10-hackberry.dtb \
sun4i-a10-hyundai-a7hd.dtb \
sun4i-a10-mk802ii.dtb \
sun4i-a10-olinuxino-lime.dtb \
sun4i-a10-pcduino.dtb \
+ sun4i-a10-pcduino2.dtb \
sun4i-a10-pov-protab2-ips9.dtb
dtb-$(CONFIG_MACH_SUN5I) += \
sun5i-a10s-auxtek-t003.dtb \
sun5i-a10s-r7-tv-dongle.dtb \
sun5i-a10s-wobo-i5.dtb \
sun5i-a13-ampe-a76.dtb \
+ sun5i-a13-difrnce-dit4350.dtb \
sun5i-a13-empire-electronix-d709.dtb \
sun5i-a13-hsg-h702.dtb \
sun5i-a13-inet-86vs.dtb \
sun6i-a31-m9.dtb \
sun6i-a31-mele-a1000g-quad.dtb \
sun6i-a31-mixtile-loftq.dtb \
+ sun6i-a31s-colorfly-e708-q1.dtb \
sun6i-a31s-cs908.dtb \
sun6i-a31s-primo81.dtb \
- sun6i-a31s-sinovoip-bpi-m2.dtb
+ sun6i-a31s-sina31s.dtb \
+ sun6i-a31s-sinovoip-bpi-m2.dtb \
+ sun6i-a31s-yones-toptech-bs1078-v2.dtb
dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-ainol-aw1.dtb \
sun7i-a20-bananapi.dtb \
sun7i-a20-cubietruck.dtb \
sun7i-a20-hummingbird.dtb \
sun7i-a20-i12-tvbox.dtb \
+ sun7i-a20-icnova-swac.dtb \
+ sun7i-a20-itead-ibox.dtb \
sun7i-a20-lamobo-r1.dtb \
sun7i-a20-m3.dtb \
sun7i-a20-m5.dtb \
dtb-$(CONFIG_MACH_SUN8I_A23) += \
sun8i-a23-evb.dtb \
sun8i-a23-gt90h-v4.dtb \
+ sun8i-a23-polaroid-mid2809pxe04.dtb \
sun8i-a23-q8-tablet.dtb
dtb-$(CONFIG_MACH_SUN8I_A33) += \
sun8i-a33-ga10h-v1.1.dtb \
sun8i-a33-sinlinx-sina33.dtb
dtb-$(CONFIG_MACH_SUN8I_A83T) += \
sun8i-a83t-allwinner-h8homlet-v2.dtb \
+ sun8i-a83t-cubietruck-plus.dtb \
sun8i-a83t-sinovoip-bpi-m3.dtb
dtb-$(CONFIG_MACH_SUN8I_H3) += \
+ sun8i-h3-orangepi-2.dtb \
sun8i-h3-orangepi-pc.dtb \
sun8i-h3-orangepi-plus.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
--- /dev/null
+/*
+ * Copyright 2015 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * AXP221/221s/223 Integrated Power Management Chip
+ * http://www.x-powers.com/product/AXP22X.php
+ * http://dl.linux-sunxi.org/AXP/AXP221%20Datasheet%20V1.2%2020130326%20.pdf
+ */
+
+&axp22x {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ regulators {
+ /* Default work frequency for buck regulators */
+ x-powers,dcdc-freq = <3000>;
+
+ reg_dcdc1: dcdc1 {
+ regulator-name = "dcdc1";
+ };
+
+ reg_dcdc2: dcdc2 {
+ regulator-name = "dcdc2";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-name = "dcdc3";
+ };
+
+ reg_dcdc4: dcdc4 {
+ regulator-name = "dcdc4";
+ };
+
+ reg_dcdc5: dcdc5 {
+ regulator-name = "dcdc5";
+ };
+
+ reg_dc1sw: dc1sw {
+ regulator-name = "dc1sw";
+ };
+
+ reg_dc5ldo: dc5ldo {
+ regulator-name = "dc5ldo";
+ };
+
+ reg_aldo1: aldo1 {
+ regulator-name = "aldo1";
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-name = "aldo2";
+ };
+
+ reg_aldo3: aldo3 {
+ regulator-name = "aldo3";
+ };
+
+ reg_dldo1: dldo1 {
+ regulator-name = "dldo1";
+ };
+
+ reg_dldo2: dldo2 {
+ regulator-name = "dldo2";
+ };
+
+ reg_dldo3: dldo3 {
+ regulator-name = "dldo3";
+ };
+
+ reg_dldo4: dldo4 {
+ regulator-name = "dldo4";
+ };
+
+ reg_eldo1: eldo1 {
+ regulator-name = "eldo1";
+ };
+
+ reg_eldo2: eldo2 {
+ regulator-name = "eldo2";
+ };
+
+ reg_eldo3: eldo3 {
+ regulator-name = "eldo3";
+ };
+
+ reg_ldo_io0: ldo_io0 {
+ regulator-name = "ldo_io0";
+ status = "disabled";
+ };
+
+ reg_ldo_io1: ldo_io1 {
+ regulator-name = "ldo_io1";
+ status = "disabled";
+ };
+
+ reg_rtc_ldo: rtc_ldo {
+ /* RTC_LDO is a fixed, always-on regulator */
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "rtc_ldo";
+ };
+ };
+};
status = "okay";
};
+&codec {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "Chuwi V7 CW0825";
};
};
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+
+ ft5306de4: touchscreen@38 {
+ compatible = "edt,edt-ft5406";
+ reg = <0x38>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>;
+ touchscreen-size-x = <1024>;
+ touchscreen-size-y = <768>;
+ };
+};
+
&lradc {
vref-supply = <®_vcc3v0>;
status = "okay";
status = "okay";
};
+&codec {
+ status = "okay";
+};
+
&cpu0 {
cpu-supply = <®_dcdc2>;
};
--- /dev/null
+/*
+ * Copyright 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "Dserve DSRV9703C";
+ compatible = "dserve,dsrv9703c", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_en_pin_dsrv9703c>;
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ haptics {
+ compatible = "regulator-haptic";
+ haptic-supply = <®_motor>;
+ min-microvolt = <3000000>;
+ max-microvolt = <3000000>;
+ };
+
+ reg_motor: reg_motor {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&motor_pins>;
+ regulator-name = "vcc-motor";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ enable-active-high;
+ gpio = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
+ };
+};
+
+&codec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&codec_pa_pin>;
+ allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupts = <0>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ /* pull-ups and devices require AXP209 LDO3 */
+ status = "failed";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+
+ ft5406ee8: touchscreen@38 {
+ compatible = "edt,edt-ft5406";
+ reg = <0x38>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchscreen_pins>;
+ reset-gpios = <&pio 1 13 GPIO_ACTIVE_LOW>;
+ touchscreen-size-x = <1024>;
+ touchscreen-size-y = <768>;
+ };
+};
+
+&lradc {
+ vref-supply = <®_ldo2>;
+ status = "okay";
+
+ button@400 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <400000>;
+ };
+
+ button@800 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <800000>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ bl_en_pin_dsrv9703c: bl_en_pin@0 {
+ allwinner,pins = "PH7";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ codec_pa_pin: codec_pa_pin@0 {
+ allwinner,pins = "PH15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ motor_pins: motor_pins@0 {
+ allwinner,pins = "PB3";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ touchscreen_pins: touchscreen_pins@0 {
+ allwinner,pins = "PB13";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
+ allwinner,pins = "PH5";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins_a>;
+ status = "okay";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb0_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "Gemei G9 Tablet";
/*
* TODO:
* 2x cameras via CSI
- * bma250 IRQs
* AXP battery management
* NAND
* OTG
* Touchscreen - gt801_2plus1 @ i2c adapter 2 @ 0x48
*/
+&codec {
+ /* PH15 controls power to external amplifier (ft2012q) */
+ pinctrl-names = "default";
+ pinctrl-0 = <&codec_pa_pin>;
+ allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
&ehci0 {
status = "okay";
status = "okay";
axp209: pmic@34 {
- compatible = "x-powers,axp209";
reg = <0x34>;
interrupts = <0>;
-
- interrupt-controller;
- #interrupt-cells = <1>;
};
};
+#include "axp209.dtsi"
+
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
bma250@18 {
compatible = "bosch,bma250";
reg = <0x18>;
-
- /*
- * TODO: interrupt pins:
- * int1 - PH00
- * int2 - PI10
- */
+ interrupt-parent = <&pio>;
+ interrupts = <7 0 IRQ_TYPE_EDGE_RISING>; /* PH00 / EINT0 */
};
};
&lradc {
- vref-supply = <®_vcc3v0>;
+ vref-supply = <®_ldo2>;
status = "okay";
status = "okay";
};
+&pio {
+ codec_pa_pin: codec_pa_pin@0 {
+ allwinner,pins = "PH15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
®_usb1_vbus {
status = "okay";
};
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
/ {
model = "iNet-1";
serial0 = &uart0;
};
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_en_pin_inet>;
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+ };
+
chosen {
stdout-path = "serial0:115200n8";
};
};
+&codec {
+ status = "okay";
+};
+
&cpu0 {
cpu-supply = <®_dcdc2>;
};
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
+
+ ft5x: touchscreen@38 {
+ compatible = "edt,edt-ft5406";
+ reg = <0x38>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchscreen_wake_pin>;
+ wake-gpios = <&pio 1 13 GPIO_ACTIVE_HIGH>; /* PB13 */
+ touchscreen-size-x = <600>;
+ touchscreen-size-y = <1024>;
+ touchscreen-swapped-x-y;
+ };
};
&lradc {
};
&pio {
+ bl_en_pin_inet: bl_en_pin@0 {
+ allwinner,pins = "PH7";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ touchscreen_wake_pin: touchscreen_wake_pin@0 {
+ allwinner,pins = "PB13";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
usb0_id_detect_pin: usb0_id_detect_pin@0 {
allwinner,pins = "PH4";
allwinner,function = "gpio_in";
};
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins_a>;
+ status = "okay";
+};
+
®_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "INet-97F Rev 02";
};
};
-&ehci0 {
- status = "okay";
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
};
&ehci1 {
status = "okay";
axp209: pmic@34 {
- compatible = "x-powers,axp209";
reg = <0x34>;
interrupts = <0>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+
+ ft5406ee8: touchscreen@38 {
+ compatible = "edt,edt-ft5406";
+ reg = <0x38>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>;
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ };
+};
+
+&lradc {
+ vref-supply = <®_ldo2>;
+ status = "okay";
+
+ button@200 {
+ label = "Menu";
+ linux,code = <KEY_MENU>;
+ channel = <0>;
+ voltage = <200000>;
+ };
+
+ button@600 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <600000>;
+ };
- interrupt-controller;
- #interrupt-cells = <1>;
+ button@800 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <800000>;
+ };
+
+ button@1000 {
+ label = "Home";
+ linux,code = <KEY_HOMEPAGE>;
+ channel = <0>;
+ voltage = <1000000>;
+ };
+
+ button@1200 {
+ label = "Esc";
+ linux,code = <KEY_ESC>;
+ channel = <0>;
+ voltage = <1200000>;
};
};
status = "okay";
};
-&ohci0 {
+&otg_sram {
status = "okay";
};
-&ohci1 {
- status = "okay";
+&pio {
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
+ allwinner,pins = "PH5";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ };
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
};
-®_usb1_vbus {
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb0_vbus {
status = "okay";
};
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usbphy {
- usb1_vbus-supply = <®_usb1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_vbus-supply = <®_usb0_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
};
chosen {
stdout-path = "serial0:115200n8";
};
+
+ gpio_keys {
+ compatible = "gpio-keys-polled";
+ pinctrl-names = "default";
+ pinctrl-0 = <&key_pins_inet9f>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ button@0 {
+ label = "Left Joystick Left";
+ linux,code = <ABS_X>;
+ linux,input-type = <EV_ABS>;
+ linux,input-value = <0xffffffff>; /* -1 */
+ gpios = <&pio 0 6 GPIO_ACTIVE_LOW>; /* PA6 */
+ };
+
+ button@1 {
+ label = "Left Joystick Right";
+ linux,code = <ABS_X>;
+ linux,input-type = <EV_ABS>;
+ linux,input-value = <1>;
+ gpios = <&pio 0 5 GPIO_ACTIVE_LOW>; /* PA5 */
+ };
+
+ button@2 {
+ label = "Left Joystick Up";
+ linux,code = <ABS_Y>;
+ linux,input-type = <EV_ABS>;
+ linux,input-value = <0xffffffff>; /* -1 */
+ gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
+ };
+
+ button@3 {
+ label = "Left Joystick Down";
+ linux,code = <ABS_Y>;
+ linux,input-type = <EV_ABS>;
+ linux,input-value = <1>;
+ gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
+ };
+
+ button@4 {
+ label = "Right Joystick Left";
+ linux,code = <ABS_Z>;
+ linux,input-type = <EV_ABS>;
+ linux,input-value = <0xffffffff>; /* -1 */
+ gpios = <&pio 0 1 GPIO_ACTIVE_LOW>; /* PA1 */
+ };
+
+ button@5 {
+ label = "Right Joystick Right";
+ linux,code = <ABS_Z>;
+ linux,input-type = <EV_ABS>;
+ linux,input-value = <1>;
+ gpios = <&pio 0 0 GPIO_ACTIVE_LOW>; /* PA0 */
+ };
+
+ button@6 {
+ label = "Right Joystick Up";
+ linux,code = <ABS_RZ>;
+ linux,input-type = <EV_ABS>;
+ linux,input-value = <0xffffffff>; /* -1 */
+ gpios = <&pio 0 3 GPIO_ACTIVE_LOW>; /* PA3 */
+ };
+
+ button@7 {
+ label = "Right Joystick Down";
+ linux,code = <ABS_RZ>;
+ linux,input-type = <EV_ABS>;
+ linux,input-value = <1>;
+ gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */
+ };
+
+ button@8 {
+ label = "DPad Left";
+ linux,code = <ABS_HAT0X>;
+ linux,input-type = <EV_ABS>;
+ linux,input-value = <0xffffffff>; /* -1 */
+ gpios = <&pio 7 23 GPIO_ACTIVE_LOW>; /* PH23 */
+ };
+
+ button@9 {
+ label = "DPad Right";
+ linux,code = <ABS_HAT0X>;
+ linux,input-type = <EV_ABS>;
+ linux,input-value = <1>;
+ gpios = <&pio 7 24 GPIO_ACTIVE_LOW>; /* PH24 */
+ };
+
+ button@10 {
+ label = "DPad Up";
+ linux,code = <ABS_HAT0Y>;
+ linux,input-type = <EV_ABS>;
+ linux,input-value = <0xffffffff>; /* -1 */
+ gpios = <&pio 7 25 GPIO_ACTIVE_LOW>; /* PH25 */
+ };
+
+ button@11 {
+ label = "DPad Down";
+ linux,code = <ABS_HAT0Y>;
+ linux,input-type = <EV_ABS>;
+ linux,input-value = <1>;
+ gpios = <&pio 7 26 GPIO_ACTIVE_LOW>; /* PH26 */
+ };
+
+ button@12 {
+ label = "Button X";
+ linux,code = <BTN_X>;
+ gpios = <&pio 0 16 GPIO_ACTIVE_LOW>; /* PA16 */
+ };
+
+ button@13 {
+ label = "Button Y";
+ linux,code = <BTN_Y>;
+ gpios = <&pio 0 14 GPIO_ACTIVE_LOW>; /* PA14 */
+ };
+
+ button@14 {
+ label = "Button A";
+ linux,code = <BTN_A>;
+ gpios = <&pio 0 17 GPIO_ACTIVE_LOW>; /* PA17 */
+ };
+
+ button@15 {
+ label = "Button B";
+ linux,code = <BTN_B>;
+ gpios = <&pio 0 15 GPIO_ACTIVE_LOW>; /* PA15 */
+ };
+
+ button@16 {
+ label = "Select Button";
+ linux,code = <BTN_SELECT>;
+ gpios = <&pio 0 11 GPIO_ACTIVE_LOW>; /* PA11 */
+ };
+
+ button@17 {
+ label = "Start Button";
+ linux,code = <BTN_START>;
+ gpios = <&pio 0 12 GPIO_ACTIVE_LOW>; /* PA12 */
+ };
+
+ button@18 {
+ label = "Top Left Button";
+ linux,code = <BTN_TL>;
+ gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */
+ };
+
+ button@19 {
+ label = "Top Right Button";
+ linux,code = <BTN_TR>;
+ gpios = <&pio 0 13 GPIO_ACTIVE_LOW>; /* PA13 */
+ };
+ };
};
&cpu0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
+
+ /* Accelerometer */
+ bma250@18 {
+ compatible = "bosch,bma250";
+ reg = <0x18>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 0 IRQ_TYPE_EDGE_RISING>; /* PH0 / EINT0 */
+ };
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
+
+ ft5406ee8: touchscreen@38 {
+ compatible = "edt,edt-ft5406";
+ reg = <0x38>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>;
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ };
};
&lradc {
};
&pio {
+ key_pins_inet9f: key_pins@0 {
+ allwinner,pins = "PA0", "PA1", "PA3", "PA4",
+ "PA5", "PA6", "PA8", "PA9",
+ "PA11", "PA12", "PA13",
+ "PA14", "PA15", "PA16", "PA17",
+ "PH22", "PH23", "PH24", "PH25", "PH26";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
usb0_id_detect_pin: usb0_id_detect_pin@0 {
allwinner,pins = "PH4";
allwinner,function = "gpio_in";
/*
* Copyright 2015 Josef Gajdusek <atx@atx.name>
+ * Copyright 2015 - Marcus Cooper <codekipper@gmail.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
/dts-v1/;
#include "sun4i-a10.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include "sunxi-itead-core-common.dtsi"
/ {
model = "Iteaduino Plus A10";
compatible = "itead,iteaduino-plus-a10", "allwinner,sun4i-a10";
-
- aliases {
- serial0 = &uart0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
};
&ahci {
status = "okay";
};
-&cpu0 {
- cpu-supply = <®_dcdc2>;
-};
-
-&ehci0 {
- status = "okay";
-};
-
-&ehci1 {
- status = "okay";
-};
-
&emac {
pinctrl-names = "default";
pinctrl-0 = <&emac_pins_a>;
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
axp209: pmic@34 {
- reg = <0x34>;
interrupts = <0>;
};
};
status = "okay";
};
-&ohci0 {
- status = "okay";
-};
-
-&ohci1 {
- status = "okay";
-};
-
®_ahci_5v {
status = "okay";
};
-#include "axp209.dtsi"
-
-®_dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1450000>;
- regulator-name = "vdd-cpu";
-};
-
-®_dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-int-dll";
-};
-
-®_ldo1 {
- regulator-name = "vdd-rtc";
-};
-
-®_ldo2 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "avcc";
-};
-
-®_usb1_vbus {
- status = "okay";
-};
-
-®_usb2_vbus {
- status = "okay";
-};
-
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi0_pins_a>,
<&spi0_cs0_pins_a>;
status = "okay";
};
-
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
- status = "okay";
-};
-
-&usbphy {
- usb1_vbus-supply = <®_usb1_vbus>;
- usb2_vbus-supply = <®_usb2_vbus>;
- status = "okay";
-};
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
emac_power_pin_q5: emac_power_pin@0 {
allwinner,pins = "PH19";
};
};
+®_usb0_vbus {
+ regulator-boot-on;
+ status = "okay";
+};
+
®_usb1_vbus {
status = "okay";
};
status = "okay";
};
+&usb_otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
&usbphy {
+ usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
status = "okay";
};
+&codec {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
led_pins_marsboard: led_pins@0 {
allwinner,pins = "PB5", "PB6", "PB7", "PB8";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
};
®_usb1_vbus {
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
#include "sun4i-a10.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "MK802";
};
};
+&codec {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
+ allwinner,pins = "PH5";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
usb2_vbus_pin_mk802: usb2_vbus_pin@0 {
allwinner,pins = "PH12";
allwinner,function = "gpio_out";
};
};
+®_usb0_vbus {
+ status = "okay";
+};
+
®_usb1_vbus {
status = "okay";
};
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+ usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
};
};
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+
+ eeprom: eeprom@50 {
+ compatible = "atmel,24c16";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
+
&mdio {
status = "okay";
};
};
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
&ehci0 {
status = "okay";
};
status = "okay";
axp209: pmic@34 {
- compatible = "x-powers,axp209";
reg = <0x34>;
interrupts = <0>;
-
- interrupt-controller;
- #interrupt-cells = <1>;
};
};
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
led_pins_pcduino: led_pins@0 {
allwinner,pins = "PH15", "PH16";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
};
-®_usb1_vbus {
- status = "okay";
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
};
-®_usb2_vbus {
- status = "okay";
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
};
&uart0 {
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usbphy {
- usb1_vbus-supply = <®_usb1_vbus>;
- usb2_vbus-supply = <®_usb2_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb1_vbus-supply = <®_vcc5v0>; /* USB1 VBUS is always on */
+ usb2_vbus-supply = <®_vcc5v0>; /* USB2 VBUS is always on */
status = "okay";
};
--- /dev/null
+/*
+ * Copyright 2015 Siarhei Siamashka <siarhei.siamashka@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * The LinkSprite pcDuino2 board is almost identical to the older
+ * LinkSprite pcDuino1 board. The only software visible difference
+ * is that the pcDuino2 board got a USB VBUS voltage regulator, which
+ * is controlled by the PD2 pin (pulled-up by default). Also one of
+ * the USB host ports has been replaced with a USB WIFI chip.
+ */
+
+#include "sun4i-a10-pcduino.dts"
+
+/ {
+ model = "LinkSprite pcDuino2";
+ compatible = "linksprite,a10-pcduino2", "allwinner,sun4i-a10";
+};
+
+&pio {
+ usb2_vbus_pin_pcduino2: usb2_vbus_pin@0 {
+ allwinner,pins = "PD2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb2_vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb2_vbus_pin_pcduino2>;
+ gpio = <&pio 3 2 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_vcc3v3>; /* USB WIFI is always on */
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
/ {
model = "Point of View Protab2-IPS9";
serial0 = &uart0;
};
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_en_pin_protab>;
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+ };
+
chosen {
stdout-path = "serial0:115200n8";
};
};
+&codec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&codec_pa_pin>;
+ allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
+ status = "okay";
+};
+
&cpu0 {
cpu-supply = <®_dcdc2>;
};
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
+
+ /* Accelerometer */
+ bma250@18 {
+ compatible = "bosch,bma250";
+ reg = <0x18>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 0 IRQ_TYPE_EDGE_RISING>; /* PH0 / EINT0 */
+ };
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
+
+ pixcir_ts@5c {
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchscreen_pins>;
+ compatible = "pixcir,pixcir_tangoc";
+ reg = <0x5c>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21 (PH21) */
+ attb-gpio = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* PH21 */
+ enable-gpios = <&pio 0 5 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&pio 1 13 GPIO_ACTIVE_LOW>;
+ touchscreen-size-x = <1024>;
+ touchscreen-size-y = <768>;
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ };
};
&lradc {
};
&pio {
+ bl_en_pin_protab: bl_en_pin@0 {
+ allwinner,pins = "PH7";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ codec_pa_pin: codec_pa_pin@0 {
+ allwinner,pins = "PH15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ touchscreen_pins: touchscreen_pins@0 {
+ allwinner,pins = "PA5", "PB13";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
usb0_id_detect_pin: usb0_id_detect_pin@0 {
allwinner,pins = "PH4";
allwinner,function = "gpio_in";
};
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins_a>;
+ status = "okay";
+};
+
®_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
#include <dt-bindings/thermal/thermal.h>
+#include <dt-bindings/clock/sun4i-a10-pll2.h>
#include <dt-bindings/dma/sun4i-a10.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
- <&ahb_gates 44>;
+ <&ahb_gates 44>, <&dram_gates 26>;
status = "disabled";
};
"simple-framebuffer";
allwinner,pipeline = "de_fe0-de_be0-lcd0-hdmi";
clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
- <&ahb_gates 44>, <&ahb_gates 46>;
+ <&ahb_gates 44>, <&ahb_gates 46>,
+ <&dram_gates 25>, <&dram_gates 26>;
status = "disabled";
};
"simple-framebuffer";
allwinner,pipeline = "de_fe0-de_be0-lcd0";
clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>,
- <&ahb_gates 46>;
+ <&ahb_gates 46>, <&dram_gates 25>,
+ <&dram_gates 26>;
status = "disabled";
};
"simple-framebuffer";
allwinner,pipeline = "de_fe0-de_be0-lcd0-tve0";
clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>,
- <&ahb_gates 44>, <&ahb_gates 46>;
+ <&ahb_gates 44>, <&ahb_gates 46>,
+ <&dram_gates 25>, <&dram_gates 26>;
status = "disabled";
};
};
clock-output-names = "pll1";
};
+ pll2: clk@01c20008 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-pll2-clk";
+ reg = <0x01c20008 0x8>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll2-1x", "pll2-2x",
+ "pll2-4x", "pll2-8x";
+ };
+
pll4: clk@01c20018 {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-pll1-clk";
compatible = "allwinner,sun4i-a10-axi-gates-clk";
reg = <0x01c2005c 0x4>;
clocks = <&axi>;
+ clock-indices = <0>;
clock-output-names = "axi_dram";
};
compatible = "allwinner,sun4i-a10-ahb-gates-clk";
reg = <0x01c20060 0x8>;
clocks = <&ahb>;
+ clock-indices = <0>, <1>,
+ <2>, <3>,
+ <4>, <5>, <6>,
+ <7>, <8>, <9>,
+ <10>, <11>, <12>,
+ <13>, <14>, <16>,
+ <17>, <18>, <20>,
+ <21>, <22>, <23>,
+ <24>, <25>, <26>,
+ <32>, <33>, <34>,
+ <35>, <36>, <37>,
+ <40>, <41>, <43>,
+ <44>, <45>,
+ <46>, <47>,
+ <50>, <52>;
clock-output-names = "ahb_usb0", "ahb_ehci0",
- "ahb_ohci0", "ahb_ehci1", "ahb_ohci1", "ahb_ss",
- "ahb_dma", "ahb_bist", "ahb_mmc0", "ahb_mmc1",
- "ahb_mmc2", "ahb_mmc3", "ahb_ms", "ahb_nand",
- "ahb_sdram", "ahb_ace", "ahb_emac", "ahb_ts",
- "ahb_spi0", "ahb_spi1", "ahb_spi2", "ahb_spi3",
- "ahb_pata", "ahb_sata", "ahb_gps", "ahb_ve",
- "ahb_tvd", "ahb_tve0", "ahb_tve1", "ahb_lcd0",
- "ahb_lcd1", "ahb_csi0", "ahb_csi1", "ahb_hdmi",
- "ahb_de_be0", "ahb_de_be1", "ahb_de_fe0",
- "ahb_de_fe1", "ahb_mp", "ahb_mali400";
+ "ahb_ohci0", "ahb_ehci1",
+ "ahb_ohci1", "ahb_ss", "ahb_dma",
+ "ahb_bist", "ahb_mmc0", "ahb_mmc1",
+ "ahb_mmc2", "ahb_mmc3", "ahb_ms",
+ "ahb_nand", "ahb_sdram", "ahb_ace",
+ "ahb_emac", "ahb_ts", "ahb_spi0",
+ "ahb_spi1", "ahb_spi2", "ahb_spi3",
+ "ahb_pata", "ahb_sata", "ahb_gps",
+ "ahb_ve", "ahb_tvd", "ahb_tve0",
+ "ahb_tve1", "ahb_lcd0", "ahb_lcd1",
+ "ahb_csi0", "ahb_csi1", "ahb_hdmi",
+ "ahb_de_be0", "ahb_de_be1",
+ "ahb_de_fe0", "ahb_de_fe1",
+ "ahb_mp", "ahb_mali400";
};
apb0: apb0@01c20054 {
compatible = "allwinner,sun4i-a10-apb0-gates-clk";
reg = <0x01c20068 0x4>;
clocks = <&apb0>;
+ clock-indices = <0>, <1>,
+ <2>, <3>,
+ <5>, <6>,
+ <7>, <10>;
clock-output-names = "apb0_codec", "apb0_spdif",
- "apb0_ac97", "apb0_iis", "apb0_pio", "apb0_ir0",
- "apb0_ir1", "apb0_keypad";
+ "apb0_ac97", "apb0_iis",
+ "apb0_pio", "apb0_ir0",
+ "apb0_ir1", "apb0_keypad";
};
apb1: clk@01c20058 {
compatible = "allwinner,sun4i-a10-apb1-gates-clk";
reg = <0x01c2006c 0x4>;
clocks = <&apb1>;
+ clock-indices = <0>, <1>,
+ <2>, <4>,
+ <5>, <6>,
+ <7>, <16>,
+ <17>, <18>,
+ <19>, <20>,
+ <21>, <22>,
+ <23>;
clock-output-names = "apb1_i2c0", "apb1_i2c1",
- "apb1_i2c2", "apb1_can", "apb1_scr",
- "apb1_ps20", "apb1_ps21", "apb1_uart0",
- "apb1_uart1", "apb1_uart2", "apb1_uart3",
- "apb1_uart4", "apb1_uart5", "apb1_uart6",
- "apb1_uart7";
+ "apb1_i2c2", "apb1_can",
+ "apb1_scr", "apb1_ps20",
+ "apb1_ps21", "apb1_uart0",
+ "apb1_uart1", "apb1_uart2",
+ "apb1_uart3", "apb1_uart4",
+ "apb1_uart5", "apb1_uart6",
+ "apb1_uart7";
};
nand_clk: clk@01c20080 {
clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
clock-output-names = "spi3";
};
+
+ dram_gates: clk@01c20100 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-dram-gates-clk";
+ reg = <0x01c20100 0x4>;
+ clocks = <&pll5 0>;
+ clock-indices = <0>,
+ <1>, <2>,
+ <3>,
+ <4>,
+ <5>, <6>,
+ <15>,
+ <24>, <25>,
+ <26>, <27>,
+ <28>, <29>;
+ clock-output-names = "dram_ve",
+ "dram_csi0", "dram_csi1",
+ "dram_ts",
+ "dram_tvd",
+ "dram_tve0", "dram_tve1",
+ "dram_output",
+ "dram_de_fe1", "dram_de_fe0",
+ "dram_de_be0", "dram_de_be1",
+ "dram_de_mp", "dram_ace";
+ };
+
+ ve_clk: clk@01c2013c {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-ve-clk";
+ reg = <0x01c2013c 0x4>;
+ clocks = <&pll4>;
+ clock-output-names = "ve";
+ };
+
+ codec_clk: clk@01c20140 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-codec-clk";
+ reg = <0x01c20140 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "codec";
+ };
};
soc@01c00000 {
status = "disabled";
};
+ crypto: crypto-engine@01c15000 {
+ compatible = "allwinner,sun4i-a10-crypto";
+ reg = <0x01c15000 0x1000>;
+ interrupts = <86>;
+ clocks = <&ahb_gates 5>, <&ss_clk>;
+ clock-names = "ahb", "mod";
+ };
+
spi2: spi@01c17000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c17000 0x1000>;
status = "disabled";
};
+ codec: codec@01c22c00 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun4i-a10-codec";
+ reg = <0x01c22c00 0x40>;
+ interrupts = <30>;
+ clocks = <&apb0_gates 0>, <&codec_clk>;
+ clock-names = "apb", "codec";
+ dmas = <&dma SUN4I_DMA_NORMAL 19>,
+ <&dma SUN4I_DMA_NORMAL 19>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
sid: eeprom@01c23800 {
compatible = "allwinner,sun4i-a10-sid";
reg = <0x01c23800 0x10>;
status = "okay";
};
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp152: pmic@30 {
+ compatible = "x-powers,axp152";
+ reg = <0x30>;
+ interrupts = <0>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t004>;
status = "okay";
at24@50 {
- compatible = "at,24c16";
+ compatible = "atmel,24c16";
pagesize = <16>;
reg = <0x50>;
read-only;
--- /dev/null
+/*
+ * Copyright 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "Difrnce DIT4350";
+ compatible = "difrnce,dit4350", "allwinner,sun5i-a13";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ /* TODO: backlight uses axp gpio1 as enable pin */
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupts = <0>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+
+ pcf8563: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&lradc {
+ vref-supply = <®_ldo2>;
+ status = "okay";
+
+ button@200 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <200000>;
+ };
+
+ button@400 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <400000>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_d709>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
+ cd-inverted;
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_d709: mmc0_cd_pin@0 {
+ allwinner,pins = "PG0";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
+ allwinner,pins = "PG1";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ };
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PG2";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins>;
+ status = "okay";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd-int-pll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_ldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_usb0_vbus {
+ gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_b>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb0_vbus_pin_a {
+ allwinner,pins = "PG12";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+ usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+ usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_ldo3>;
+ status = "okay";
+};
&mmc0 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_inet98fv2>;
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_d709>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
status = "okay";
};
-&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_a>;
- vmmc-supply = <®_vcc3v3>;
- bus-width = <8>;
- non-removable;
- status = "okay";
-
- mmccard: mmccard@0 {
- reg = <0>;
- compatible = "mmc-card";
- broken-hpi;
- };
-};
-
&otg_sram {
status = "okay";
};
&pio {
- mmc0_cd_pin_inet98fv2: mmc0_cd_pin@0 {
+ mmc0_cd_pin_d709: mmc0_cd_pin@0 {
allwinner,pins = "PG0";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
status = "okay";
};
-&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_a>;
- vmmc-supply = <®_vcc3v3>;
- bus-width = <8>;
- non-removable;
- status = "okay";
-
- mmccard: mmccard@0 {
- reg = <0>;
- compatible = "mmc-card";
- broken-hpi;
- };
-};
-
&otg_sram {
status = "okay";
};
status = "okay";
};
-®_usb1_vbus {
- gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
- status = "okay";
-};
-
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins_b>;
allwinner,pins = "PG12";
};
-&usb1_vbus_pin_a {
- allwinner,pins = "PG11";
-};
-
&usbphy {
pinctrl-names = "default";
pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
usb0_vbus-supply = <®_usb0_vbus>;
- usb1_vbus-supply = <®_usb1_vbus>;
+ usb1_vbus-supply = <®_ldo3>;
status = "okay";
};
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
/ {
model = "Utoo P66";
compatible = "utoo,p66", "allwinner,sun5i-a13";
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ /* Note levels of 10 / 20% result in backlight off */
+ brightness-levels = <0 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <6>;
+ /* TODO: backlight uses axp gpio1 as enable pin */
+ };
+
i2c_lcd: i2c@0 {
/* The lcd panel i2c interface is hooked up via gpios */
compatible = "i2c-gpio";
};
};
+&codec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&codec_pa_pin>;
+ allwinner,pa-gpios = <&pio 6 3 GPIO_ACTIVE_HIGH>; /* PG3 */
+ status = "okay";
+};
+
&cpu0 {
cpu-supply = <®_dcdc2>;
};
};
&pio {
+ codec_pa_pin: codec_pa_pin@0 {
+ allwinner,pins = "PG3";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
mmc0_cd_pin_p66: mmc0_cd_pin@0 {
allwinner,pins = "PG0";
allwinner,function = "gpio_in";
};
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins>;
+ status = "okay";
+};
+
®_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
*/
#include "sunxi-q8-common.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+
/ {
aliases {
serial0 = &uart1;
};
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ /* TODO: backlight uses axp gpio1 as enable pin */
+ };
+
chosen {
stdout-path = "serial0:115200n8";
};
chosen {
stdout-path = "serial0:115200n8";
};
+
+ wifi_reg_on: wifi_reg_on {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&chip_wifi_reg_on_pin>;
+
+ regulator-name = "wifi-reg-on";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 2 19 GPIO_ACTIVE_HIGH>; /* PC19 */
+ enable-active-high;
+ };
+};
+
+&codec {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
};
&ehci0 {
};
};
+&mmc0_pins_a {
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>;
- vmmc-supply = <®_vcc3v3>;
+ vmmc-supply = <&wifi_reg_on>;
bus-width = <4>;
non-removable;
status = "okay";
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+ chip_wifi_reg_on_pin: chip_wifi_reg_on_pin@0 {
+ allwinner,pins = "PC19";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
chip_id_det_pin: chip_id_det_pin@0 {
allwinner,pins = "PG2";
allwinner,function = "gpio_in";
regulator-always-on;
};
+®_ldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vdd-wifi1";
+ regulator-always-on;
+};
+
+®_ldo4 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vdd-wifi2";
+ regulator-always-on;
+};
+
®_ldo5 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
#include "skeleton.dtsi"
+#include <dt-bindings/clock/sun4i-a10-pll2.h>
#include <dt-bindings/dma/sun4i-a10.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
clock-output-names = "pll1";
};
+ pll2: clk@01c20008 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun5i-a13-pll2-clk";
+ reg = <0x01c20008 0x8>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll2-1x", "pll2-2x",
+ "pll2-4x", "pll2-8x";
+ };
+
pll4: clk@01c20018 {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-pll1-clk";
clock-output-names = "usb_ohci0", "usb_phy";
};
+ codec_clk: clk@01c20140 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-codec-clk";
+ reg = <0x01c20140 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "codec";
+ };
+
mbus_clk: clk@01c2015c {
#clock-cells = <0>;
compatible = "allwinner,sun5i-a13-mbus-clk";
status = "disabled";
};
+ codec: codec@01c22c00 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun4i-a10-codec";
+ reg = <0x01c22c00 0x40>;
+ interrupts = <30>;
+ clocks = <&apb0_gates 0>, <&codec_clk>;
+ clock-names = "apb", "codec";
+ dmas = <&dma SUN4I_DMA_NORMAL 19>,
+ <&dma SUN4I_DMA_NORMAL 19>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
sid: eeprom@01c23800 {
compatible = "allwinner,sun4i-a10-sid";
reg = <0x01c23800 0x10>;
chosen {
stdout-path = "serial0:115200n8";
};
+
+ i2c_lcd: i2c@0 {
+ /* The lcd panel i2c interface is hooked up via gpios */
+ compatible = "i2c-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_lcd_pins>;
+ gpios = <&pio 0 23 GPIO_ACTIVE_HIGH>, /* PA23, sda */
+ <&pio 0 24 GPIO_ACTIVE_HIGH>; /* PA24, scl */
+ i2c-gpio,delay-us = <5>;
+ };
};
&ehci1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
+
+ mma8452: mma8452@1d {
+ compatible = "fsl,mma8452";
+ reg = <0x1d>;
+ interrupt-parent = <&pio>;
+ interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PA9 */
+ };
};
&mmc0 {
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+
+ i2c_lcd_pins: i2c_lcd_pin@0 {
+ allwinner,pins = "PA23", "PA24";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
};
®_usb2_vbus {
compatible = "merrii,a31-hummingbird", "allwinner,sun6i-a31";
aliases {
+ rtc0 = &pcf8563;
+ rtc1 = &rtc;
serial0 = &uart0;
};
};
};
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
+};
+
&ehci0 {
status = "okay";
};
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_pins_rgmii_a>, <&gmac_phy_reset_pin_hummingbird>;
phy = <&phy1>;
phy-mode = "rgmii";
snps,reset-gpio = <&pio 0 21 GPIO_ACTIVE_HIGH>;
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_hummingbird>;
- vmmc-supply = <&vcc_3v0>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
cd-inverted;
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins_a>, <&wifi_reset_pin_hummingbird>;
- vmmc-supply = <&vcc_wifi>;
+ vmmc-supply = <®_aldo1>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
};
&pio {
+ gmac_phy_reset_pin_hummingbird: gmac_phy_reset_pin@0 {
+ allwinner,pins = "PA21";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
mmc0_cd_pin_hummingbird: mmc0_cd_pin@0 {
allwinner,pins = "PA8";
allwinner,function = "gpio_in";
&p2wi {
status = "okay";
- axp221: pmic@68 {
+ axp22x: pmic@68 {
compatible = "x-powers,axp221";
reg = <0x68>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <1>;
- dcdc1-supply = <&vcc_3v0>;
- dcdc5-supply = <&vcc_dram>;
-
- regulators {
- x-powers,dcdc-freq = <3000>;
-
- vcc_3v0: dcdc1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-3v0";
- };
-
- vdd_cpu: dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <1320000>;
- regulator-name = "vdd-cpu";
- };
-
- vdd_gpu: dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <1320000>;
- regulator-name = "vdd-gpu";
- };
-
- vdd_sys_dll: dcdc4 {
- regulator-always-on;
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- regulator-name = "vdd-sys-dll";
- };
-
- vcc_dram: dcdc5 {
- regulator-always-on;
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1500000>;
- regulator-name = "vcc-dram";
- };
-
- vcc_wifi: aldo1 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc_wifi";
- };
-
- avcc: aldo3 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "avcc";
- };
- };
};
};
+#include "axp22x.dtsi"
+
+®_aldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc5ldo {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
®_usb1_vbus {
gpio = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */
status = "okay";
#size-cells = <1>;
ranges;
- framebuffer@0 {
+ simplefb_hdmi: framebuffer@0 {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
status = "disabled";
};
- framebuffer@1 {
+ simplefb_lcd: framebuffer@1 {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
compatible = "allwinner,sun6i-a31-ahb1-gates-clk";
reg = <0x01c20060 0x8>;
clocks = <&ahb1>;
+ clock-indices = <1>, <5>,
+ <6>, <8>, <9>,
+ <10>, <11>, <12>,
+ <13>, <14>,
+ <17>, <18>, <19>,
+ <20>, <21>, <22>,
+ <23>, <24>, <26>,
+ <27>, <29>,
+ <30>, <31>, <32>,
+ <36>, <37>, <40>,
+ <43>, <44>, <45>,
+ <46>, <47>, <50>,
+ <52>, <55>, <56>,
+ <57>, <58>;
clock-output-names = "ahb1_mipidsi", "ahb1_ss",
"ahb1_dma", "ahb1_mmc0", "ahb1_mmc1",
"ahb1_mmc2", "ahb1_mmc3", "ahb1_nand1",
compatible = "allwinner,sun6i-a31-apb1-gates-clk";
reg = <0x01c20068 0x4>;
clocks = <&apb1>;
+ clock-indices = <0>, <4>,
+ <5>, <12>,
+ <13>;
clock-output-names = "apb1_codec", "apb1_digital_mic",
"apb1_pio", "apb1_daudio0",
"apb1_daudio1";
compatible = "allwinner,sun6i-a31-apb2-gates-clk";
reg = <0x01c2006c 0x4>;
clocks = <&apb2>;
+ clock-indices = <0>, <1>,
+ <2>, <3>, <16>,
+ <17>, <18>, <19>,
+ <20>, <21>;
clock-output-names = "apb2_i2c0", "apb2_i2c1",
"apb2_i2c2", "apb2_i2c3",
"apb2_uart0", "apb2_uart1",
"mmc3_sample";
};
+ ss_clk: clk@01c2009c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c2009c 0x4>;
+ clocks = <&osc24M>, <&pll6 0>;
+ clock-output-names = "ss";
+ };
+
spi0_clk: clk@01c200a0 {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-mod0-clk";
compatible = "allwinner,sun6i-a31-usb-clk";
reg = <0x01c200cc 0x4>;
clocks = <&osc24M>;
+ clock-indices = <8>, <9>, <10>,
+ <16>, <17>,
+ <18>;
clock-output-names = "usb_phy0", "usb_phy1", "usb_phy2",
"usb_ohci0", "usb_ohci1",
"usb_ohci2";
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+ mmc3_8bit_emmc_pins: mmc3@1 {
+ allwinner,pins = "PC6", "PC7", "PC8", "PC9",
+ "PC10", "PC11", "PC12",
+ "PC13", "PC14", "PC15",
+ "PC24";
+ allwinner,function = "mmc3";
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
gmac_pins_mii_a: gmac_mii@0 {
allwinner,pins = "PA0", "PA1", "PA2", "PA3",
"PA8", "PA9", "PA11",
reg = <0x01c20ca0 0x20>;
};
+ lradc: lradc@01c22800 {
+ compatible = "allwinner,sun4i-a10-lradc-keys";
+ reg = <0x01c22800 0x100>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
rtp: rtp@01c25000 {
compatible = "allwinner,sun6i-a31-ts";
reg = <0x01c25000 0x100>;
#size-cells = <0>;
};
+ crypto: crypto-engine@01c15000 {
+ compatible = "allwinner,sun4i-a10-crypto";
+ reg = <0x01c15000 0x1000>;
+ interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb1_gates 5>, <&ss_clk>;
+ clock-names = "ahb", "mod";
+ resets = <&ahb1_rst 5>;
+ reset-names = "ahb";
+ };
+
timer@01c60000 {
compatible = "allwinner,sun6i-a31-hstimer",
"allwinner,sun7i-a20-hstimer";
resets = <&apb0_rst 0>;
gpio-controller;
interrupt-controller;
- #interrupt-cells = <2>;
+ #interrupt-cells = <3>;
#size-cells = <0>;
#gpio-cells = <3>;
--- /dev/null
+/*
+ * Copyright 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun6i-a31s.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Colorfly E708 Q1 tablet";
+ compatible = "colorfly,e708-q1", "allwinner,sun6i-a31s";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
+};
+
+&ehci0 {
+ /* rtl8188etv wifi is connected here */
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <®_aldo3>;
+ status = "okay";
+
+ button@1000 {
+ label = "Home";
+ linux,code = <KEY_HOMEPAGE>;
+ channel = <0>;
+ voltage = <1000000>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_e708_q1>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ mma8452_int_e708_q1: mma8452_int_pin@0 {
+ allwinner,pins = "PA9";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc0_cd_pin_e708_q1: mmc0_cd_pin@0 {
+ allwinner,pins = "PA8";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+&p2wi {
+ status = "okay";
+
+ axp22x: pmic@68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc1sw {
+ regulator-name = "vcc-lcd";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus"; /* This is an educated guess */
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pg";
+};
+
+&simplefb_lcd {
+ vcc-lcd-supply = <®_dc1sw>;
+ vcc-pg-supply = <®_dldo2>;
+};
+
+/*
+ * FIXME for now we only support host mode and rely on u-boot to have
+ * turned on Vbus which is controlled by the axp221 pmic on the board.
+ *
+ * Once we have axp221 power-supply and vbus-usb support we should switch
+ * to fully supporting otg.
+ */
+&usb_otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_dldo1>;
+ status = "okay";
+};
/*
- * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ * Copyright 2014 Siarhei Siamashka <siarhei.siamashka@gmail.com>
+ * Copyright 2015 Karsten Merker <merker@debian.org>
+ * Copyright 2015 Chen-Yu Tsai <wens@csie.org>
*
- * Minimal dts file for the MSI Primo81 for u-boot only
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
*
- * SPDX-License-Identifier: GPL-2.0+ or X11
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun6i-a31s.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
- model = "MSI Primo81";
+ model = "MSI Primo81 tablet";
compatible = "msi,primo81", "allwinner,sun6i-a31s";
aliases {
};
};
-&uart0 {
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
+};
+
+&ehci0 {
+ /* rtl8188etv wifi is connected here */
+ status = "okay";
+};
+
+&i2c0 {
+ /* pull-ups and device VDDIO use AXP221 DLDO3 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "failed";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+
+ ctp@5d {
+ pinctrl-names = "default";
+ pinctrl-0 = <>911_int_primo81>;
+ compatible = "goodix,gt911";
+ reg = <0x5d>;
+ interrupt-parent = <&pio>;
+ interrupts = <0 3 IRQ_TYPE_LEVEL_HIGH>; /* PA3 */
+ touchscreen-swapped-x-y;
+ };
+};
+
+&i2c2 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+
+ accelerometer@1c {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mma8452_int_primo81>;
+ compatible = "fsl,mma8452";
+ reg = <0x1c>;
+ interrupt-parent = <&pio>;
+ interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; /* PA9 */
+ #io-channel-cells = <1>;
+ };
+};
+
+&lradc {
+ vref-supply = <®_aldo3>;
+ status = "okay";
+
+ button@158 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <158730>;
+ };
+
+ button@349 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <349206>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_primo81>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ gt911_int_primo81: gt911_int_pin@0 {
+ allwinner,pins = "PA3";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mma8452_int_primo81: mma8452_int_pin@0 {
+ allwinner,pins = "PA9";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc0_cd_pin_primo81: mmc0_cd_pin@0 {
+ allwinner,pins = "PA8";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+&p2wi {
+ status = "okay";
+
+ axp22x: pmic@68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc1sw {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-lcd";
+};
+
+®_dc5ldo {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus"; /* This is an educated guess */
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_dldo3 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vddio-csi";
+};
+
+®_eldo3 {
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-mipi-bridge";
+};
+
+&simplefb_lcd {
+ vcc-lcd-supply = <®_dc1sw>;
+ vdd-mipi-bridge-supply = <®_eldo3>;
+};
+
+&usb_otg {
+ /* otg support requires support for AXP221 usb-power-supply and GPIO */
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_dldo1>;
status = "okay";
};
--- /dev/null
+/*
+ * Copyright 2015 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun6i-a31s.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Sinlinx SinA31s Core Board";
+ compatible = "sinlinx,sina31s", "allwinner,sun6i-a31s";
+
+ aliases {
+ serial0 = &uart0;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
+};
+
+/* eMMC on core board */
+&mmc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_8bit_emmc_pins>;
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+/* AXP221s PMIC on core board */
+&p2wi {
+ status = "okay";
+
+ axp22x: pmic@68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc5ldo {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+/* UART0 pads available on core board */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
--- /dev/null
+/*
+ * Copyright 2015 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/* The SinA31s development board has the SinA31s core board soldered on */
+#include "sun6i-a31s-sina31s-core.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Sinlinx SinA31s Development Board";
+ compatible = "sinlinx,sina31s-sdk", "allwinner,sun6i-a31s";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pin_sina31s>;
+
+ status {
+ label = "sina31s:status:usr";
+ gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */
+ };
+ };
+};
+
+&ehci0 {
+ /* USB 2.0 4 port hub IC */
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_mii_a>;
+ phy = <&phy1>;
+ phy-mode = "mii";
+ phy-supply = <®_dldo1>;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <®_aldo3>;
+ status = "okay";
+
+ button@158 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <158730>;
+ };
+
+ button@349 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <349206>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_sina31s>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 0 4 GPIO_ACTIVE_HIGH>; /* PA4 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ led_pin_sina31s: led_pin@0 {
+ allwinner,pins = "PH13";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_sina31s: mmc0_cd_pin@0 {
+ allwinner,pins = "PA4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-gmac-phy";
+};
+
+&usbphy {
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Lawrence Yu <lyu@micile.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun6i-a31s.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Yones TopTech BS1078 v2 Tablet";
+ compatible = "yones-toptech,bs1078-v2", "allwinner,sun6i-a31s";
+
+ aliases {
+ serial0 = &uart0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_bs1078v2: mmc0_cd_pin@0 {
+ allwinner,pins = "PA8";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bs1078v2>;
+ vmmc-supply = <®_vcc3v0>;
+ bus-width = <4>;
+ cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc0_pins_a {
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&p2wi {
+ status = "okay";
+
+ axp22x: pmic@68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc1sw {
+ regulator-name = "vcc-lcd-usb2";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+};
+
+®_dc5ldo {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+/* Voltage source for I2C pullup resistors for I2C Bus 0 */
+®_dldo3 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vddio-csi";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_dldo1>;
+ usb2_vbus-supply = <®_dc1sw>;
+ status = "okay";
+};
status = "okay";
};
+&codec {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+ operating-points = <
+ /* kHz uV */
+ 960000 1400000
+ 912000 1400000
+ 864000 1350000
+ 720000 1250000
+ 528000 1150000
+ 312000 1100000
+ 144000 1050000
+ >;
+};
+
&ehci0 {
status = "okay";
};
status = "okay";
axp209: pmic@34 {
- compatible = "x-powers,axp209";
reg = <0x34>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
- interrupt-controller;
- #interrupt-cells = <1>;
};
};
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
mmc0_cd_pin_bananapi: mmc0_cd_pin@0 {
allwinner,pins = "PH10";
allwinner,function = "gpio_in";
};
};
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb0_vbus {
+ status = "okay";
+};
+
®_usb1_vbus {
status = "okay";
};
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
status = "okay";
};
+&codec {
+ status = "okay";
+};
+
&cpu0 {
cpu-supply = <®_dcdc2>;
};
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
led_pins_cubieboard2: led_pins@0 {
allwinner,pins = "PH20", "PH21";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
};
®_ahci_5v {
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
#include "axp209.dtsi"
®_dcdc2 {
};
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
status = "okay";
};
+&codec {
+ status = "okay";
+};
+
&cpu0 {
cpu-supply = <®_dcdc2>;
};
--- /dev/null
+/*
+ * Copyright 2015 Stefan Roese <sr@denx.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "ICnova-A20 SWAC";
+ compatible = "swac,icnova-a20-swac", "incircuit,icnova-a20", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_mii_a>;
+ phy = <&phy1>;
+ phy-mode = "mii";
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 8 5 GPIO_ACTIVE_HIGH>; /* PI5 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 - Marcus Cooper <codekipper@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-itead-core-common.dtsi"
+
+/ {
+ model = "Itead Ibox A20";
+ compatible = "itead,itead-ibox-a20", "allwinner,sun7i-a20";
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_itead_core>;
+
+ green {
+ label = "itead_core:green:usr";
+ gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ blue {
+ label = "itead_core:blue:usr";
+ gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&codec {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_mii_a>;
+ phy = <&phy1>;
+ phy-mode = "mii";
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ axp209: pmic@34 {
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_rx_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ led_pins_itead_core: led_pins@0 {
+ allwinner,pins = "PH20","PH21";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_ahci_5v {
+ status = "okay";
+};
&cpu0 {
cpu-supply = <®_dcdc2>;
- operating-points = <
- /* kHz uV */
- 960000 1400000
- 912000 1400000
- 864000 1350000
- 720000 1250000
- 528000 1150000
- 312000 1100000
- 144000 1050000
- >;
};
&ehci0 {
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "mk808c";
};
};
+&codec {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
+ allwinner,pins = "PH5";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb0_vbus {
+ status = "okay";
+};
+
®_usb1_vbus {
status = "okay";
};
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+ usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
/*
* Copyright 2015 - Marcus Cooper <codekipper@gmail.com>
+ * Copyright 2015 - Karsten Merker <merker@debian.org>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
default-state = "on";
};
};
-
- reg_axp_ipsout: axp_ipsout {
- compatible = "regulator-fixed";
- regulator-name = "axp-ipsout";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- };
};
&ahci {
status = "okay";
};
+&codec {
+ status = "okay";
+};
+
&gmac {
pinctrl-names = "default";
pinctrl-0 = <&gmac_pins_rgmii_a>;
};
};
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
+&lradc {
+ vref-supply = <®_vcc3v0>;
status = "okay";
+
+ button@190 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <190000>;
+ };
+
+ button@390 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <390000>;
+ };
+
+ button@600 {
+ label = "Menu";
+ linux,code = <KEY_MENU>;
+ channel = <0>;
+ voltage = <600000>;
+ };
+
+ button@800 {
+ label = "Search";
+ linux,code = <KEY_SEARCH>;
+ channel = <0>;
+ voltage = <800000>;
+ };
+
+ button@980 {
+ label = "Home";
+ linux,code = <KEY_HOMEPAGE>;
+ channel = <0>;
+ voltage = <980000>;
+ };
+
+ button@1180 {
+ label = "Esc";
+ linux,code = <KEY_ESC>;
+ channel = <0>;
+ voltage = <1180000>;
+ };
+
+ button@1400 {
+ label = "Enter";
+ linux,code = <KEY_ENTER>;
+ channel = <0>;
+ voltage = <1400000>;
+ };
};
&mmc0 {
status = "okay";
};
+&mmc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins_a>, <&mmc3_cd_pin_olimex_som_evb>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 0 GPIO_ACTIVE_HIGH>; /* PH0 */
+ cd-inverted;
+ status = "okay";
+};
+
&ohci0 {
status = "okay";
};
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+ mmc3_cd_pin_olimex_som_evb: mmc3_cd_pin@0 {
+ allwinner,pins = "PH0";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH04";
+ allwinner,pins = "PH4";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PH05";
+ allwinner,pins = "PH5";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
®_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1425000>;
+ regulator-max-microvolt = <1400000>;
regulator-name = "vdd-cpu";
};
&usbphy {
pinctrl-names = "default";
pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpios = <&pio 7 04 GPIO_ACTIVE_HIGH>; /* PH04 */
- usb0_vbus_det-gpios = <&pio 7 05 GPIO_ACTIVE_HIGH>; /* PH05 */
+ usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH04 */
+ usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH05 */
usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
};
};
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+
+ eeprom: eeprom@50 {
+ compatible = "atmel,24c16";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
+
+ eeprom: eeprom@50 {
+ compatible = "atmel,24c16";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
};
&mmc0 {
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
ahci_pwr_pin_olinuxinolime: ahci_pwr_pin@1 {
allwinner,pins = "PC3";
allwinner,drive = <SUN4I_PINCTRL_20_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
+ allwinner,pins = "PH5";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ };
+
+ usb0_vbus_pin_lime2: usb0_vbus_pin@0 {
+ allwinner,pins = "PC17";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};
®_ahci_5v {
status = "okay";
};
+®_usb0_vbus {
+ pinctrl-0 = <&usb0_vbus_pin_lime2>;
+ gpio = <&pio 2 17 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
®_usb1_vbus {
status = "okay";
};
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
+
+ eeprom: eeprom@50 {
+ compatible = "atmel,24c16";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
};
&i2c2 {
status = "okay";
};
+&codec {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
mmc0_cd_pin_orangepi: mmc0_cd_pin@0 {
allwinner,pins = "PH10";
allwinner,function = "gpio_in";
regulator-name = "avcc";
};
+®_usb0_vbus {
+ status = "okay";
+};
+
®_usb1_vbus {
pinctrl-0 = <&usb1_vbus_pin_bananapro>;
gpio = <&pio 7 26 GPIO_ACTIVE_HIGH>; /* PH26 */
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
mmc0_cd_pin_orangepi: mmc0_cd_pin@0 {
allwinner,pins = "PH10";
allwinner,function = "gpio_in";
regulator-name = "avcc";
};
+®_usb0_vbus {
+ status = "okay";
+};
+
®_usb1_vbus {
pinctrl-0 = <&usb1_vbus_pin_bananapro>;
gpio = <&pio 7 26 GPIO_ACTIVE_HIGH>; /* PH26 */
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
status = "okay";
};
+&codec {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
&ehci0 {
status = "okay";
};
status = "okay";
axp209: pmic@34 {
- compatible = "x-powers,axp209";
reg = <0x34>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
- interrupt-controller;
- #interrupt-cells = <1>;
};
};
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
ahci_pwr_pin_pcduino3_nano: ahci_pwr_pin@0 {
allwinner,pins = "PH2";
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
usb1_vbus_pin_pcduino3_nano: usb1_vbus_pin@0 {
- allwinner,pins = "PH11";
+ allwinner,pins = "PD2";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
status = "okay";
};
-®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_pcduino3_nano>;
- gpio = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
- status = "okay";
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-pll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
};
-®_usb2_vbus {
+/* A single regulator (U24) powers both USB host ports. */
+®_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_pcduino3_nano>;
+ gpio = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */
status = "okay";
};
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
usb1_vbus-supply = <®_usb1_vbus>;
- usb2_vbus-supply = <®_usb2_vbus>;
+ usb2_vbus-supply = <®_usb1_vbus>;
status = "okay";
};
allwinner,pins = "PH2";
};
+&codec {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
&ehci0 {
status = "okay";
};
status = "okay";
axp209: pmic@34 {
- compatible = "x-powers,axp209";
reg = <0x34>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
- interrupt-controller;
- #interrupt-cells = <1>;
};
};
+#include "axp209.dtsi"
+
&ir0 {
pinctrl-names = "default";
pinctrl-0 = <&ir0_rx_pins_a>;
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
led_pins_pcduino3: led_pins@0 {
allwinner,pins = "PH15", "PH16";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
};
®_ahci_5v {
status = "okay";
};
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-pll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
®_usb1_vbus {
status = "okay";
};
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
/ {
model = "Wexler TAB7200";
serial0 = &uart0;
};
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_enable_pin>;
+ enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+ };
+
chosen {
stdout-path = "serial0:115200n8";
};
};
+&codec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&codec_pa_pin>;
+ allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
+ status = "okay";
+};
+
&cpu0 {
cpu-supply = <®_dcdc2>;
};
};
};
+#include "axp209.dtsi"
+
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
+
+ gt911: touchscreen@5d {
+ compatible = "goodix,gt911";
+ reg = <0x5d>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21 (PH21) */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_reset_pin>;
+ irq-gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* INT (PH21) */
+ reset-gpios = <&pio 1 13 GPIO_ACTIVE_HIGH>; /* RST (PB13) */
+ touchscreen-swapped-x-y;
+ };
};
&lradc {
status = "okay";
};
-#include "axp209.dtsi"
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ bl_enable_pin: bl_enable_pin@0 {
+ allwinner,pins = "PH7";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ codec_pa_pin: codec_pa_pin@0 {
+ allwinner,pins = "PH15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ ts_reset_pin: ts_reset_pin@0 {
+ allwinner,pins = "PB13";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins_a>;
+ status = "okay";
+};
®_dcdc2 {
regulator-always-on;
regulator-name = "avcc";
};
+®_usb0_vbus {
+ status = "okay";
+};
+
®_usb1_vbus {
status = "okay";
};
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
/*
- * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ * Copyright 2015 Jelle de Jong <jelledejong@powercraft.nl>
*
- * Minimal dts file for the Wits Pro A20 DKT for u-boot only
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
*
- * SPDX-License-Identifier: GPL-2.0+ or X11
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "Wits Pro A20 DKT";
chosen {
stdout-path = "serial0:115200n8";
};
+
+ mmc3_pwrseq: mmc3_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vmmc3_pin_ap6xxx_wl_regon>;
+ reset-gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; /* PH9 WIFI_EN */
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
};
&ehci0 {
};
};
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+#include "axp209.dtsi"
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&mmc3_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <7 10 IRQ_TYPE_LEVEL_LOW>; /* PH10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
&ohci0 {
status = "okay";
};
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ vmmc3_pin_ap6xxx_wl_regon: vmmc3_pin@0 {
+ allwinner,pins = "PH9";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb0_vbus {
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/thermal/thermal.h>
+#include <dt-bindings/clock/sun4i-a10-pll2.h>
#include <dt-bindings/dma/sun4i-a10.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
- <&ahb_gates 44>;
+ <&ahb_gates 44>, <&dram_gates 26>;
status = "disabled";
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
- clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>;
+ clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>,
+ <&dram_gates 26>;
status = "disabled";
};
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-tve0";
clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>,
- <&ahb_gates 44>;
+ <&ahb_gates 44>, <&dram_gates 26>;
status = "disabled";
};
};
720000 1200000
528000 1100000
312000 1000000
- 144000 900000
+ 144000 1000000
>;
#cooling-cells = <2>;
cooling-min-level = <0>;
clock-output-names = "pll1";
};
+ pll2: clk@01c20008 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-pll2-clk";
+ reg = <0x01c20008 0x8>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll2-1x", "pll2-2x",
+ "pll2-4x", "pll2-8x";
+ };
+
pll4: clk@01c20018 {
#clock-cells = <0>;
compatible = "allwinner,sun7i-a20-pll4-clk";
compatible = "allwinner,sun7i-a20-ahb-gates-clk";
reg = <0x01c20060 0x8>;
clocks = <&ahb>;
+ clock-indices = <0>, <1>,
+ <2>, <3>, <4>,
+ <5>, <6>, <7>, <8>,
+ <9>, <10>, <11>, <12>,
+ <13>, <14>, <16>,
+ <17>, <18>, <20>, <21>,
+ <22>, <23>, <25>,
+ <28>, <32>, <33>, <34>,
+ <35>, <36>, <37>, <40>,
+ <41>, <42>, <43>,
+ <44>, <45>, <46>,
+ <47>, <49>, <50>,
+ <52>;
clock-output-names = "ahb_usb0", "ahb_ehci0",
"ahb_ohci0", "ahb_ehci1", "ahb_ohci1",
"ahb_ss", "ahb_dma", "ahb_bist", "ahb_mmc0",
compatible = "allwinner,sun7i-a20-apb0-gates-clk";
reg = <0x01c20068 0x4>;
clocks = <&apb0>;
+ clock-indices = <0>, <1>,
+ <2>, <3>, <4>,
+ <5>, <6>, <7>,
+ <8>, <10>;
clock-output-names = "apb0_codec", "apb0_spdif",
"apb0_ac97", "apb0_iis0", "apb0_iis1",
"apb0_pio", "apb0_ir0", "apb0_ir1",
compatible = "allwinner,sun7i-a20-apb1-gates-clk";
reg = <0x01c2006c 0x4>;
clocks = <&apb1>;
+ clock-indices = <0>, <1>,
+ <2>, <3>, <4>,
+ <5>, <6>, <7>,
+ <15>, <16>, <17>,
+ <18>, <19>, <20>,
+ <21>, <22>, <23>;
clock-output-names = "apb1_i2c0", "apb1_i2c1",
"apb1_i2c2", "apb1_i2c3", "apb1_can",
"apb1_scr", "apb1_ps20", "apb1_ps21",
clock-output-names = "ir1";
};
+ keypad_clk: clk@01c200c4 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200c4 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "keypad";
+ };
+
usb_clk: clk@01c200cc {
#clock-cells = <1>;
#reset-cells = <1>;
clock-output-names = "spi3";
};
+ dram_gates: clk@01c20100 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-dram-gates-clk";
+ reg = <0x01c20100 0x4>;
+ clocks = <&pll5 0>;
+ clock-indices = <0>,
+ <1>, <2>,
+ <3>,
+ <4>,
+ <5>, <6>,
+ <15>,
+ <24>, <25>,
+ <26>, <27>,
+ <28>, <29>;
+ clock-output-names = "dram_ve",
+ "dram_csi0", "dram_csi1",
+ "dram_ts",
+ "dram_tvd",
+ "dram_tve0", "dram_tve1",
+ "dram_output",
+ "dram_de_fe1", "dram_de_fe0",
+ "dram_de_be0", "dram_de_be1",
+ "dram_de_mp", "dram_ace";
+ };
+
+ ve_clk: clk@01c2013c {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-ve-clk";
+ reg = <0x01c2013c 0x4>;
+ clocks = <&pll4>;
+ clock-output-names = "ve";
+ };
+
+ codec_clk: clk@01c20140 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-codec-clk";
+ reg = <0x01c20140 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "codec";
+ };
+
mbus_clk: clk@01c2015c {
#clock-cells = <0>;
compatible = "allwinner,sun5i-a13-mbus-clk";
status = "disabled";
};
+ crypto: crypto-engine@01c15000 {
+ compatible = "allwinner,sun4i-a10-crypto";
+ reg = <0x01c15000 0x1000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb_gates 5>, <&ss_clk>;
+ clock-names = "ahb", "mod";
+ };
+
spi2: spi@01c17000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c17000 0x1000>;
status = "disabled";
};
+ codec: codec@01c22c00 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun7i-a20-codec";
+ reg = <0x01c22c00 0x40>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 0>, <&codec_clk>;
+ clock-names = "apb", "codec";
+ dmas = <&dma SUN4I_DMA_NORMAL 19>,
+ <&dma SUN4I_DMA_NORMAL 19>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
sid: eeprom@01c23800 {
compatible = "allwinner,sun7i-a20-sid";
reg = <0x01c23800 0x200>;
#size-cells = <1>;
ranges;
- framebuffer@0 {
+ simplefb_lcd: framebuffer@0 {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
clock-output-names = "apb1";
};
- ahb1_gates: clk@01c20060 {
- #clock-cells = <1>;
- compatible = "allwinner,sun8i-a23-ahb1-gates-clk";
- reg = <0x01c20060 0x8>;
- clocks = <&ahb1>;
- clock-output-names = "ahb1_mipidsi", "ahb1_dma",
- "ahb1_mmc0", "ahb1_mmc1", "ahb1_mmc2",
- "ahb1_nand", "ahb1_sdram",
- "ahb1_hstimer", "ahb1_spi0",
- "ahb1_spi1", "ahb1_otg", "ahb1_ehci",
- "ahb1_ohci", "ahb1_ve", "ahb1_lcd",
- "ahb1_csi", "ahb1_be", "ahb1_fe",
- "ahb1_gpu", "ahb1_spinlock",
- "ahb1_drc";
- };
-
apb1_gates: clk@01c20068 {
#clock-cells = <1>;
compatible = "allwinner,sun8i-a23-apb1-gates-clk";
reg = <0x01c20068 0x4>;
clocks = <&apb1>;
+ clock-indices = <0>, <5>,
+ <12>, <13>;
clock-output-names = "apb1_codec", "apb1_pio",
"apb1_daudio0", "apb1_daudio1";
};
compatible = "allwinner,sun8i-a23-apb2-gates-clk";
reg = <0x01c2006c 0x4>;
clocks = <&apb2>;
+ clock-indices = <0>, <1>,
+ <2>, <16>,
+ <17>, <18>,
+ <19>, <20>;
clock-output-names = "apb2_i2c0", "apb2_i2c1",
"apb2_i2c2", "apb2_uart0",
"apb2_uart1", "apb2_uart2",
allwinner,pins = "PC5", "PC6", "PC8",
"PC9", "PC10", "PC11",
"PC12", "PC13", "PC14",
- "PC15";
+ "PC15", "PC16";
allwinner,function = "mmc2";
allwinner,drive = <SUN4I_PINCTRL_30_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+ pwm0_pins: pwm0 {
+ allwinner,pins = "PH0";
+ allwinner,function = "pwm0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
i2c0_pins_a: i2c0@0 {
allwinner,pins = "PH2", "PH3";
allwinner,function = "i2c0";
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
};
+ pwm: pwm@01c21400 {
+ compatible = "allwinner,sun7i-a20-pwm";
+ reg = <0x01c21400 0xc>;
+ clocks = <&osc24M>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
lradc: lradc@01c22800 {
compatible = "allwinner,sun4i-a10-lradc-keys";
reg = <0x01c22800 0x100>;
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
};
+ nmi_intc: interrupt-controller@01f00c0c {
+ compatible = "allwinner,sun6i-a31-sc-nmi";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x01f00c0c 0x38>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
prcm@01f01400 {
compatible = "allwinner,sun8i-a23-prcm";
reg = <0x01f01400 0x200>;
resets = <&apb0_rst 0>;
gpio-controller;
interrupt-controller;
+ #interrupt-cells = <3>;
#address-cells = <1>;
#size-cells = <0>;
#gpio-cells = <3>;
+ r_rsb_pins: r_rsb {
+ allwinner,pins = "PL0", "PL1";
+ allwinner,function = "s_rsb";
+ allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
r_uart_pins_a: r_uart@0 {
allwinner,pins = "PL2", "PL3";
allwinner,function = "s_uart";
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
+
+ r_rsb: rsb@01f03400 {
+ compatible = "allwinner,sun8i-a23-rsb";
+ reg = <0x01f03400 0x400>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 3>;
+ clock-frequency = <3000000>;
+ resets = <&apb0_rst 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_rsb_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
/ {
- model = "Allwinner GT90H Quad Core Tablet (v4)";
- compatible = "allwinner,gt90h-v4", "allwinner,sun8i-a33";
+ model = "Allwinner GT90H Dual Core Tablet (v4)";
+ compatible = "allwinner,gt90h-v4", "allwinner,sun8i-a23";
aliases {
serial0 = &r_uart;
};
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_en_pin_gt90h>;
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+ };
+
chosen {
stdout-path = "serial0:115200n8";
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_gt90h>;
- /* FIXME this really is aldo1, correct once we've pmic support */
- vmmc-supply = <®_vcc3v0>;
+ vmmc-supply = <®_aldo1>;
bus-width = <4>;
cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
cd-inverted;
};
&pio {
+ bl_en_pin_gt90h: bl_en_pin@0 {
+ allwinner,pins = "PH6";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
mmc0_cd_pin_gt90h: mmc0_cd_pin@0 {
allwinner,pins = "PB4";
allwinner,function = "gpio_in";
};
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins>;
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp22x: pmic@3a3 {
+ compatible = "x-powers,axp223";
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
+ };
+};
+
&r_uart {
pinctrl-names = "default";
pinctrl-0 = <&r_uart_pins_a>;
status = "okay";
};
+#include "axp22x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2350000>;
+ regulator-max-microvolt = <2650000>;
+ regulator-name = "vdd-dll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc1sw {
+ regulator-name = "vcc-lcd";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+&simplefb_lcd {
+ vcc-lcd-supply = <®_dc1sw>;
+};
+
/*
* FIXME for now we only support host mode and rely on u-boot to have
* turned on Vbus which is controlled by the axp223 pmic on the board.
};
&usbphy {
+ usb1_vbus-supply = <®_dldo1>;
status = "okay";
};
--- /dev/null
+/*
+ * Copyright 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a23.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "Polaroid MID2809PXE04 tablet";
+ compatible = "polaroid,mid2809pxe04", "allwinner,sun8i-a23";
+
+ aliases {
+ serial0 = &r_uart;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_en_pin_mid2809>;
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <®_vcc3v0>;
+ status = "okay";
+
+ button@200 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <200000>;
+ };
+
+ button@400 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <400000>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_mid2809>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ bl_en_pin_mid2809: bl_en_pin@0 {
+ allwinner,pins = "PH6";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_mid2809: mmc0_cd_pin@0 {
+ allwinner,pins = "PB4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins>;
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp22x: pmic@3a3 {
+ compatible = "x-powers,axp223";
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
+ };
+};
+
+&r_uart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_uart_pins_a>;
+ status = "okay";
+};
+
+#include "axp22x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2350000>;
+ regulator-max-microvolt = <2650000>;
+ regulator-name = "vdd-dll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc1sw {
+ regulator-name = "vcc-lcd";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+&simplefb_lcd {
+ vcc-lcd-supply = <®_dc1sw>;
+};
+
+/*
+ * FIXME for now we only support host mode and rely on u-boot to have
+ * turned on Vbus which is controlled by the axp223 pmic on the board.
+ *
+ * Once we have axp223 support we should switch to fully supporting otg.
+ */
+&usb_otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
};
clocks {
+ ahb1_gates: clk@01c20060 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun8i-a23-ahb1-gates-clk";
+ reg = <0x01c20060 0x8>;
+ clocks = <&ahb1>;
+ clock-indices = <1>, <6>,
+ <8>, <9>, <10>,
+ <13>, <14>,
+ <19>, <20>,
+ <21>, <24>, <26>,
+ <29>, <32>, <36>,
+ <40>, <44>, <46>,
+ <52>, <53>,
+ <54>, <57>;
+ clock-output-names = "ahb1_mipidsi", "ahb1_dma",
+ "ahb1_mmc0", "ahb1_mmc1", "ahb1_mmc2",
+ "ahb1_nand", "ahb1_sdram",
+ "ahb1_hstimer", "ahb1_spi0",
+ "ahb1_spi1", "ahb1_otg", "ahb1_ehci",
+ "ahb1_ohci", "ahb1_ve", "ahb1_lcd",
+ "ahb1_csi", "ahb1_be", "ahb1_fe",
+ "ahb1_gpu", "ahb1_msgbox",
+ "ahb1_spinlock", "ahb1_drc";
+ };
+
mbus_clk: clk@01c2015c {
#clock-cells = <0>;
compatible = "allwinner,sun8i-a23-mbus-clk";
};
&lradc {
- vref-supply = <®_vcc3v0>;
+ vref-supply = <®_dcdc1>;
status = "okay";
button@200 {
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_sina33>;
- vmmc-supply = <®_vcc3v0>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
cd-inverted;
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
- vmmc-supply = <®_vcc3v0>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <8>;
non-removable;
+ cap-mmc-hw-reset;
status = "okay";
};
&mmc2_8bit_pins {
+ /* Increase drive strength for DDR modes */
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
/* eMMC is missing pull-ups */
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
};
};
+&r_rsb {
+ status = "okay";
+
+ axp22x: pmic@3a3 {
+ compatible = "x-powers,axp223";
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2350000>;
+ regulator-max-microvolt = <2650000>;
+ regulator-name = "vdd-dll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_b>;
clock-output-names = "pll11";
};
+ ahb1_gates: clk@01c20060 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun8i-a33-ahb1-gates-clk";
+ reg = <0x01c20060 0x8>;
+ clocks = <&ahb1>;
+ clock-indices = <1>, <5>,
+ <6>, <8>, <9>,
+ <10>, <13>, <14>,
+ <19>, <20>,
+ <21>, <24>, <26>,
+ <29>, <32>, <36>,
+ <40>, <44>, <46>,
+ <52>, <53>,
+ <54>, <57>,
+ <58>;
+ clock-output-names = "ahb1_mipidsi", "ahb1_ss",
+ "ahb1_dma","ahb1_mmc0", "ahb1_mmc1",
+ "ahb1_mmc2", "ahb1_nand", "ahb1_sdram",
+ "ahb1_hstimer", "ahb1_spi0",
+ "ahb1_spi1", "ahb1_otg", "ahb1_ehci",
+ "ahb1_ohci", "ahb1_ve", "ahb1_lcd",
+ "ahb1_csi", "ahb1_be", "ahb1_fe",
+ "ahb1_gpu", "ahb1_msgbox",
+ "ahb1_spinlock", "ahb1_drc",
+ "ahb1_sat";
+ };
+
+ ss_clk: clk@01c2009c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c2009c 0x4>;
+ clocks = <&osc24M>, <&pll6 0>;
+ clock-output-names = "ss";
+ };
+
mbus_clk: clk@01c2015c {
#clock-cells = <0>;
compatible = "allwinner,sun8i-a23-mbus-clk";
};
soc@01c00000 {
+ crypto: crypto-engine@01c15000 {
+ compatible = "allwinner,sun4i-a10-crypto";
+ reg = <0x01c15000 0x1000>;
+ interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb1_gates 5>, <&ss_clk>;
+ clock-names = "ahb", "mod";
+ resets = <&ahb1_rst 5>;
+ reset-names = "ahb";
+ };
+
usb_otg: usb@01c19000 {
compatible = "allwinner,sun8i-a33-musb";
reg = <0x01c19000 0x0400>;
--- /dev/null
+/*
+ * Copyright 2015 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a83t.dtsi"
+
+/ {
+ model = "Cubietech Cubietruck Plus";
+ compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_b>;
+ status = "okay";
+};
/ {
interrupt-parent = <&gic>;
- chosen {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- };
-
cpus {
#address-cells = <1>;
#size-cells = <0>;
device_type = "cpu";
reg = <3>;
};
+
cpu@100 {
compatible = "arm,cortex-a7";
device_type = "cpu";
device_type = "cpu";
reg = <0x101>;
};
+
cpu@102 {
compatible = "arm,cortex-a7";
device_type = "cpu";
};
};
- memory {
- reg = <0x40000000 0x80000000>;
- };
-
timer {
compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- clock-frequency = <24000000>;
- arm,cpu-registers-not-fw-configured;
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
};
clocks {
#size-cells = <1>;
ranges;
+ /* TODO: PRCM block has a mux for this. */
osc24M: osc24M_clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-output-names = "osc24M";
};
- osc32k: osc32k_clk {
+ /*
+ * This is called "internal OSC" in some places.
+ * It is an internal RC-based oscillator.
+ * TODO: Its controls are in the PRCM block.
+ */
+ osc16M: osc16M_clk {
#clock-cells = <0>;
compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "osc32k";
+ clock-frequency = <16000000>;
+ clock-output-names = "osc16M";
+ };
+
+ osc16Md512: osc16Md512_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clock-div = <512>;
+ clock-mult = <1>;
+ clocks = <&osc16M>;
+ clock-output-names = "osc16M-d512";
};
};
- soc@01c00000 {
+ soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
- gic: interrupt-controller@01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
- reg = <0x01c81000 0x1000>,
- <0x01c82000 0x1000>,
- <0x01c84000 0x2000>,
- <0x01c86000 0x2000>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- };
-
pio: pinctrl@01c20800 {
compatible = "allwinner,sun8i-a83t-pinctrl";
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x01c20800 0x400>;
clocks = <&osc24M>;
gpio-controller;
#interrupt-cells = <3>;
#gpio-cells = <3>;
- i2c0_pins_a: i2c0@0 {
- allwinner,pins = "PH0", "PH1";
- allwinner,function = "i2c0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- i2c1_pins_a: i2c1@0 {
- allwinner,pins = "PH2", "PH3";
- allwinner,function = "i2c1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- i2c2_pins_a: i2c2@0 {
- allwinner,pins = "PH4", "PH5";
- allwinner,function = "i2c2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
mmc0_pins_a: mmc0@0 {
allwinner,pins = "PF0", "PF1", "PF2",
"PF3", "PF4", "PF5";
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- mmc1_pins_a: mmc1@0 {
- allwinner,pins = "PG0", "PG1", "PG2",
- "PG3", "PG4", "PG5";
- allwinner,function = "mmc1";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- mmc2_8bit_pins: mmc2_8bit {
- allwinner,pins = "PC5", "PC6", "PC8",
- "PC9", "PC10", "PC11",
- "PC12", "PC13", "PC14",
- "PC15";
- allwinner,function = "mmc2";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
uart0_pins_a: uart0@0 {
allwinner,pins = "PF2", "PF4";
allwinner,function = "uart0";
};
};
+ timer@01c20c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x01c20c00 0xa0>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ };
+
+ watchdog@01c20ca0 {
+ compatible = "allwinner,sun6i-a31-wdt";
+ reg = <0x01c20ca0 0x20>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ };
+
uart0: serial@01c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
clocks = <&osc24M>;
status = "disabled";
};
+
+ gic: interrupt-controller@01c81000 {
+ compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x1000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
};
};
--- /dev/null
+/*
+ * Copyright (C) 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi 2";
+ compatible = "xunlong,orangepi-2", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
+
+ status_led {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
+ };
+
+ pwr_led {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sw_r_opc>;
+
+ sw2 {
+ label = "sw2";
+ linux,code = <BTN_1>;
+ gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
+ };
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_pwrseq_pin_orangepi>;
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 WIFI_EN */
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&pio {
+ leds_opc: led_pins@0 {
+ allwinner,pins = "PA15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&r_pio {
+ leds_r_opc: led_pins@0 {
+ allwinner,pins = "PL10";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ sw_r_opc: key_pins@0 {
+ allwinner,pins = "PL3", "PL4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin@0 {
+ allwinner,pins = "PL7";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb1_vbus_pin_a {
+ allwinner,pins = "PG13";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
chosen {
stdout-path = "serial0:115200n8";
};
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_opc>;
+
+ status_led {
+ label = "status:red:user";
+ gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r_leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_r_opc>;
+
+ tx {
+ label = "pwr:green:user";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+ input-name = "sw4";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sw_r_opc>;
+
+ sw4@0 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
};
&ehci1 {
status = "okay";
};
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
status = "okay";
};
+&pio {
+ leds_opc: led_pins@0 {
+ allwinner,pins = "PA15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&r_pio {
+ leds_r_opc: led_pins@0 {
+ allwinner,pins = "PL10";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ sw_r_opc: key_pins@0 {
+ allwinner,pins = "PL03";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
enable-active-high;
gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
};
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_opc>;
+
+ status_led {
+ label = "status:red:user";
+ gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r_leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_r_opc>;
+
+ tx {
+ label = "pwr:green:user";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+ input-name = "sw4";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sw_r_opc>;
+
+ sw4@0 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&pio {
+ leds_opc: led_pins@0 {
+ allwinner,pins = "PA15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&r_pio {
+ leds_r_opc: led_pins@0 {
+ allwinner,pins = "PL10";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ sw_r_opc: key_pins@0 {
+ allwinner,pins = "PL03";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};
&ehci1 {
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- clock-frequency = <24000000>;
- arm,cpu-registers-not-fw-configured;
- };
-
- memory {
- reg = <0x40000000 0x80000000>;
};
clocks {
compatible = "allwinner,sun6i-a31-pll6-clk";
reg = <0x01c20028 0x4>;
clocks = <&osc24M>;
- clock-output-names = "pll6", "pll6x2", "pll6d2";
+ clock-output-names = "pll6", "pll6x2";
};
- pll8: clk@01c20044 {
- #clock-cells = <1>;
- compatible = "allwinner,sun6i-a31-pll6-clk";
- reg = <0x01c20044 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll8", "pll8x2";
+ pll6d2: pll6d2_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clock-div = <2>;
+ clock-mult = <1>;
+ clocks = <&pll6 0>;
+ clock-output-names = "pll6d2";
+ };
+
+ /* dummy clock until pll6 can be reused */
+ pll8: pll8_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <1>;
+ clock-output-names = "pll8";
};
cpu: cpu_clk@01c20050 {
#clock-cells = <0>;
compatible = "allwinner,sun8i-h3-ahb2-clk";
reg = <0x01c2005c 0x4>;
- clocks = <&ahb1>, <&pll6 2>;
+ clocks = <&ahb1>, <&pll6d2>;
clock-output-names = "ahb2";
};
<76>, <77>, <78>,
<96>, <97>, <98>,
<112>, <113>,
- <114>, <115>, <116>,
- <128>, <135>;
- clock-output-names = "ahb1_ce", "ahb1_dma", "ahb1_mmc0",
- "ahb1_mmc1", "ahb1_mmc2", "ahb1_nand",
- "ahb1_sdram", "ahb2_gmac", "ahb1_ts",
- "ahb1_hstimer", "ahb1_spi0",
- "ahb1_spi1", "ahb1_otg",
- "ahb1_otg_ehci0", "ahb1_ehic1",
- "ahb1_ehic2", "ahb1_ehic3",
- "ahb1_otg_ohci0", "ahb2_ohic1",
- "ahb2_ohic2", "ahb2_ohic3", "ahb1_ve",
- "ahb1_lcd0", "ahb1_lcd1", "ahb1_deint",
- "ahb1_csi", "ahb1_tve", "ahb1_hdmi",
- "ahb1_de", "ahb1_gpu", "ahb1_msgbox",
- "ahb1_spinlock", "apb1_codec",
- "apb1_spdif", "apb1_pio", "apb1_ths",
- "apb1_i2s0", "apb1_i2s1", "apb1_i2s2",
- "apb2_i2c0", "apb2_i2c1", "apb2_i2c2",
- "apb2_uart0", "apb2_uart1",
- "apb2_uart2", "apb2_uart3", "apb2_scr",
- "ahb1_ephy", "ahb1_dbg";
+ <114>, <115>,
+ <116>, <128>, <135>;
+ clock-output-names = "bus_ce", "bus_dma", "bus_mmc0",
+ "bus_mmc1", "bus_mmc2", "bus_nand",
+ "bus_sdram", "bus_gmac", "bus_ts",
+ "bus_hstimer", "bus_spi0",
+ "bus_spi1", "bus_otg",
+ "bus_otg_ehci0", "bus_ehci1",
+ "bus_ehci2", "bus_ehci3",
+ "bus_otg_ohci0", "bus_ohci1",
+ "bus_ohci2", "bus_ohci3", "bus_ve",
+ "bus_lcd0", "bus_lcd1", "bus_deint",
+ "bus_csi", "bus_tve", "bus_hdmi",
+ "bus_de", "bus_gpu", "bus_msgbox",
+ "bus_spinlock", "bus_codec",
+ "bus_spdif", "bus_pio", "bus_ths",
+ "bus_i2s0", "bus_i2s1", "bus_i2s2",
+ "bus_i2c0", "bus_i2c1", "bus_i2c2",
+ "bus_uart0", "bus_uart1",
+ "bus_uart2", "bus_uart3",
+ "bus_scr", "bus_ephy", "bus_dbg";
};
mmc0_clk: clk@01c20088 {
#clock-cells = <1>;
compatible = "allwinner,sun4i-a10-mmc-clk";
reg = <0x01c20088 0x4>;
- clocks = <&osc24M>, <&pll6 0>, <&pll8 0>;
+ clocks = <&osc24M>, <&pll6 0>, <&pll8>;
clock-output-names = "mmc0",
"mmc0_output",
"mmc0_sample";
#clock-cells = <1>;
compatible = "allwinner,sun4i-a10-mmc-clk";
reg = <0x01c2008c 0x4>;
- clocks = <&osc24M>, <&pll6 0>, <&pll8 0>;
+ clocks = <&osc24M>, <&pll6 0>, <&pll8>;
clock-output-names = "mmc1",
"mmc1_output",
"mmc1_sample";
#clock-cells = <1>;
compatible = "allwinner,sun4i-a10-mmc-clk";
reg = <0x01c20090 0x4>;
- clocks = <&osc24M>, <&pll6 0>, <&pll8 0>;
+ clocks = <&osc24M>, <&pll6 0>, <&pll8>;
clock-output-names = "mmc2",
"mmc2_output",
"mmc2_sample";
clocks = <&osc24M>, <&pll6 1>, <&pll5>;
clock-output-names = "mbus";
};
+
+ apb0: apb0_clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <1>;
+ clock-mult = <1>;
+ clocks = <&osc24M>;
+ clock-output-names = "apb0";
+ };
+
+ apb0_gates: clk@01f01428 {
+ compatible = "allwinner,sun8i-h3-apb0-gates-clk",
+ "allwinner,sun4i-a10-gates-clk";
+ reg = <0x01f01428 0x4>;
+ #clock-cells = <1>;
+ clocks = <&apb0>;
+ clock-indices = <0>, <1>;
+ clock-output-names = "apb0_pio", "apb0_ir";
+ };
+
+ ir_clk: ir_clk@01f01454 {
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01f01454 0x4>;
+ #clock-cells = <0>;
+ clocks = <&osc32k>, <&osc24M>;
+ clock-output-names = "ir";
+ };
};
soc {
reg = <0x01c02000 0x1000>;
interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&bus_gates 6>;
- resets = <&bus_rst 6>;
+ resets = <&ahb_rst 6>;
#dma-cells = <1>;
};
"mmc",
"output",
"sample";
- resets = <&bus_rst 8>;
+ resets = <&ahb_rst 8>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
"mmc",
"output",
"sample";
- resets = <&bus_rst 9>;
+ resets = <&ahb_rst 9>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
"mmc",
"output",
"sample";
- resets = <&bus_rst 10>;
+ resets = <&ahb_rst 10>;
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
reg = <0x01c1b000 0x100>;
interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&bus_gates 25>, <&bus_gates 29>;
- resets = <&bus_rst 25>, <&bus_rst 29>;
+ resets = <&ahb_rst 25>, <&ahb_rst 29>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&bus_gates 29>, <&bus_gates 25>,
<&usb_clk 17>;
- resets = <&bus_rst 29>, <&bus_rst 25>;
+ resets = <&ahb_rst 29>, <&ahb_rst 25>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
reg = <0x01c1c000 0x100>;
interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&bus_gates 26>, <&bus_gates 30>;
- resets = <&bus_rst 26>, <&bus_rst 30>;
+ resets = <&ahb_rst 26>, <&ahb_rst 30>;
phys = <&usbphy 2>;
phy-names = "usb";
status = "disabled";
interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&bus_gates 30>, <&bus_gates 26>,
<&usb_clk 18>;
- resets = <&bus_rst 30>, <&bus_rst 26>;
+ resets = <&ahb_rst 30>, <&ahb_rst 26>;
phys = <&usbphy 2>;
phy-names = "usb";
status = "disabled";
reg = <0x01c1d000 0x100>;
interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&bus_gates 27>, <&bus_gates 31>;
- resets = <&bus_rst 27>, <&bus_rst 31>;
+ resets = <&ahb_rst 27>, <&ahb_rst 31>;
phys = <&usbphy 3>;
phy-names = "usb";
status = "disabled";
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&bus_gates 31>, <&bus_gates 27>,
<&usb_clk 19>;
- resets = <&bus_rst 31>, <&bus_rst 27>;
+ resets = <&ahb_rst 31>, <&ahb_rst 27>;
phys = <&usbphy 3>;
phy-names = "usb";
status = "disabled";
gpio-controller;
#gpio-cells = <3>;
interrupt-controller;
- #interrupt-cells = <2>;
+ #interrupt-cells = <3>;
uart0_pins_a: uart0@0 {
allwinner,pins = "PA4", "PA5";
};
};
- bus_rst: reset@01c202c0 {
+ ahb_rst: reset@01c202c0 {
#reset-cells = <1>;
- compatible = "allwinner,sun8i-h3-bus-reset";
- reg = <0x01c202c0 0x1c>;
+ compatible = "allwinner,sun6i-a31-ahb1-reset";
+ reg = <0x01c202c0 0xc>;
+ };
+
+ apb1_rst: reset@01c202d0 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202d0 0x4>;
+ };
+
+ apb2_rst: reset@01c202d8 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202d8 0x4>;
};
timer@01c20c00 {
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&bus_gates 112>;
- resets = <&bus_rst 144>;
+ resets = <&apb2_rst 16>;
dmas = <&dma 6>, <&dma 6>;
dma-names = "rx", "tx";
status = "disabled";
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&bus_gates 113>;
- resets = <&bus_rst 145>;
+ resets = <&apb2_rst 17>;
dmas = <&dma 7>, <&dma 7>;
dma-names = "rx", "tx";
status = "disabled";
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&bus_gates 114>;
- resets = <&bus_rst 146>;
+ resets = <&apb2_rst 18>;
dmas = <&dma 8>, <&dma 8>;
dma-names = "rx", "tx";
status = "disabled";
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&bus_gates 115>;
- resets = <&bus_rst 147>;
+ resets = <&apb2_rst 19>;
dmas = <&dma 9>, <&dma 9>;
dma-names = "rx", "tx";
status = "disabled";
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
};
+
+ apb0_reset: reset@01f014b0 {
+ reg = <0x01f014b0 0x4>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ #reset-cells = <1>;
+ };
+
+ ir: ir@01f02000 {
+ compatible = "allwinner,sun5i-a13-ir";
+ clocks = <&apb0_gates 1>, <&ir_clk>;
+ clock-names = "apb", "ir";
+ resets = <&apb0_reset 1>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x01f02000 0x40>;
+ status = "disabled";
+ };
+
+ r_pio: pinctrl@01f02c00 {
+ compatible = "allwinner,sun8i-h3-r-pinctrl";
+ reg = <0x01f02c00 0x400>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 0>;
+ resets = <&apb0_reset 0>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ ir_pins_a: ir@0 {
+ allwinner,pins = "PL11";
+ allwinner,function = "s_cir_rx";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+ };
};
};
*/
#include "sunxi-q8-common.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+
/ {
aliases {
serial0 = &r_uart;
};
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_en_pin_q8>;
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+ };
+
chosen {
stdout-path = "serial0:115200n8";
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8>;
- vmmc-supply = <®_vcc3v0>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
cd-inverted;
};
};
+&r_rsb {
+ status = "okay";
+
+ axp22x: pmic@3a3 {
+ compatible = "x-powers,axp223";
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2350000>;
+ regulator-max-microvolt = <2650000>;
+ regulator-name = "vdd-dll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc1sw {
+ regulator-name = "vcc-lcd";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
&r_uart {
pinctrl-names = "default";
pinctrl-0 = <&r_uart_pins_a>;
status = "okay";
};
+
+&simplefb_lcd {
+ vcc-lcd-supply = <®_dc1sw>;
+};
stdout-path = "serial0:115200n8";
};
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_cubieboard4>;
+
+ green {
+ label = "cubieboard4:green:usr";
+ gpios = <&pio 7 17 GPIO_ACTIVE_HIGH>; /* PH17 */
+ };
+
+ red {
+ label = "cubieboard4:red:usr";
+ gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+ };
+ };
};
&pio {
+ led_pins_cubieboard4: led-pins@0 {
+ allwinner,pins = "PH6", "PH17";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
mmc0_cd_pin_cubieboard4: mmc0_cd_pin@0 {
allwinner,pins = "PH18";
allwinner,function = "gpio_in";
vmmc-supply = <®_vcc3v0>;
bus-width = <8>;
non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&mmc2_8bit_pins {
+ /* Increase drive strength for DDR modes */
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+};
+
+&r_ir {
+ status = "okay";
+};
+
+&r_rsb {
status = "okay";
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
- pinctrl-0 = <&led_pins_optimus>;
+ pinctrl-0 = <&led_pins_optimus>, <&led_r_pins_optimus>;
/* The LED names match those found on the board */
gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>;
};
- /* led3 is on PM15, in R_PIO */
+ led3 {
+ label = "optimus:led3:usr";
+ gpios = <&r_pio 1 15 GPIO_ACTIVE_HIGH>; /* PM15 */
+ };
led4 {
label = "optimus:led4:usr";
status = "okay";
};
-&i2c3 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c3_pins_a>;
- status = "okay";
-};
-
-&i2c3_pins_a {
- /* Enable internal pull-up */
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-};
-
&ohci0 {
status = "okay";
};
vmmc-supply = <®_vcc3v0>;
bus-width = <8>;
non-removable;
+ cap-mmc-hw-reset;
status = "okay";
};
+&mmc2_8bit_pins {
+ /* Increase drive strength for DDR modes */
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+};
+
®_usb1_vbus {
pinctrl-0 = <&usb1_vbus_pin_optimus>;
gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
status = "okay";
};
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+&r_ir {
status = "okay";
};
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart4_pins_a>;
+&r_pio {
+ led_r_pins_optimus: led-pins@1 {
+ allwinner,pins = "PM15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&r_rsb {
status = "okay";
};
-&uart4_pins_a {
- /* Enable internal pull-up */
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
};
&usbphy1 {
*/
ranges = <0 0 0 0x20000000>;
+ /*
+ * This clock is actually configurable from the PRCM address
+ * space. The external 24M oscillator can be turned off, and
+ * the clock switched to an internal 16M RC oscillator. Under
+ * normal operation there's no reason to do this, and the
+ * default is to use the external good one, so just model this
+ * as a fixed clock. Also it is not entirely clear if the
+ * osc24M mux in the PRCM affects the entire clock tree, which
+ * would also throw all the PLL clock rates off, or just the
+ * downstream clocks in the PRCM.
+ */
osc24M: osc24M_clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-output-names = "osc24M";
};
+ /*
+ * The 32k clock is from an external source, normally the
+ * AC100 codec/RTC chip. This clock is by default enabled
+ * and clocked at 32768 Hz, from the oscillator connected
+ * to the AC100. It is configurable, but no such driver or
+ * bindings exist yet.
+ */
osc32k: osc32k_clk {
#clock-cells = <0>;
compatible = "fixed-clock";
"usb_phy2", "usb_hsic_12M";
};
+ pll3: clk@06000008 {
+ /* placeholder until implemented */
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-rate = <0>;
+ clock-output-names = "pll3";
+ };
+
pll4: clk@0600000c {
#clock-cells = <0>;
compatible = "allwinner,sun9i-a80-pll4-clk";
compatible = "allwinner,sun9i-a80-ahb0-gates-clk";
reg = <0x06000580 0x4>;
clocks = <&ahb0>;
- clock-indices = <0>, <1>, <3>, <5>, <8>, <12>, <13>,
- <14>, <15>, <16>, <18>, <20>, <21>,
- <22>, <23>;
+ clock-indices = <0>, <1>, <3>,
+ <5>, <8>, <12>,
+ <13>, <14>,
+ <15>, <16>, <18>,
+ <20>, <21>, <22>,
+ <23>;
clock-output-names = "ahb0_fd", "ahb0_ve", "ahb0_gpu",
"ahb0_ss", "ahb0_sd", "ahb0_nand1",
"ahb0_nand0", "ahb0_sdram",
compatible = "allwinner,sun9i-a80-ahb1-gates-clk";
reg = <0x06000584 0x4>;
clocks = <&ahb1>;
- clock-indices = <0>, <1>, <17>, <21>, <22>, <23>, <24>;
+ clock-indices = <0>, <1>,
+ <17>, <21>,
+ <22>, <23>,
+ <24>;
clock-output-names = "ahb1_usbotg", "ahb1_usbhci",
"ahb1_gmac", "ahb1_msgbox",
"ahb1_spinlock", "ahb1_hstimer",
compatible = "allwinner,sun9i-a80-ahb2-gates-clk";
reg = <0x06000588 0x4>;
clocks = <&ahb2>;
- clock-indices = <0>, <1>, <2>, <4>, <5>, <7>, <8>,
- <11>;
+ clock-indices = <0>, <1>,
+ <2>, <4>, <5>,
+ <7>, <8>, <11>;
clock-output-names = "ahb2_lcd0", "ahb2_lcd1",
"ahb2_edp", "ahb2_csi", "ahb2_hdmi",
"ahb2_de", "ahb2_mp", "ahb2_mipi_dsi";
compatible = "allwinner,sun9i-a80-apb0-gates-clk";
reg = <0x06000590 0x4>;
clocks = <&apb0>;
- clock-indices = <1>, <5>, <11>, <12>, <13>, <15>,
- <17>, <18>, <19>;
+ clock-indices = <1>, <5>,
+ <11>, <12>, <13>,
+ <15>, <17>, <18>,
+ <19>;
clock-output-names = "apb0_spdif", "apb0_pio",
"apb0_ac97", "apb0_i2s0", "apb0_i2s1",
"apb0_lradc", "apb0_gpadc", "apb0_twd",
compatible = "allwinner,sun9i-a80-apb1-gates-clk";
reg = <0x06000594 0x4>;
clocks = <&apb1>;
- clock-indices = <0>, <1>, <2>, <3>, <4>,
- <16>, <17>, <18>, <19>, <20>, <21>;
+ clock-indices = <0>, <1>,
+ <2>, <3>, <4>,
+ <16>, <17>,
+ <18>, <19>,
+ <20>, <21>;
clock-output-names = "apb1_i2c0", "apb1_i2c1",
"apb1_i2c2", "apb1_i2c3", "apb1_i2c4",
"apb1_uart0", "apb1_uart1",
"apb1_uart2", "apb1_uart3",
"apb1_uart4", "apb1_uart5";
};
+
+ cpus_clk: clk@08001410 {
+ compatible = "allwinner,sun9i-a80-cpus-clk";
+ reg = <0x08001410 0x4>;
+ #clock-cells = <0>;
+ clocks = <&osc32k>, <&osc24M>, <&pll4>, <&pll3>;
+ clock-output-names = "cpus";
+ };
+
+ ahbs: ahbs_clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <1>;
+ clock-mult = <1>;
+ clocks = <&cpus_clk>;
+ clock-output-names = "ahbs";
+ };
+
+ apbs: clk@0800141c {
+ compatible = "allwinner,sun8i-a23-apb0-clk";
+ reg = <0x0800141c 0x4>;
+ #clock-cells = <0>;
+ clocks = <&ahbs>;
+ clock-output-names = "apbs";
+ };
+
+ apbs_gates: clk@08001428 {
+ compatible = "allwinner,sun9i-a80-apbs-gates-clk";
+ reg = <0x08001428 0x4>;
+ #clock-cells = <1>;
+ clocks = <&apbs>;
+ clock-indices = <0>, <1>,
+ <2>, <3>,
+ <4>, <5>,
+ <6>, <7>,
+ <12>, <13>,
+ <16>, <17>,
+ <18>, <20>;
+ clock-output-names = "apbs_pio", "apbs_ir",
+ "apbs_timer", "apbs_rsb",
+ "apbs_uart", "apbs_1wire",
+ "apbs_i2c0", "apbs_i2c1",
+ "apbs_ps2_0", "apbs_ps2_1",
+ "apbs_dma", "apbs_i2s0",
+ "apbs_i2s1", "apbs_twd";
+ };
+
+ r_1wire_clk: clk@08001450 {
+ reg = <0x08001450 0x4>;
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ clocks = <&osc32k>, <&osc24M>;
+ clock-output-names = "r_1wire";
+ };
+
+ r_ir_clk: clk@08001454 {
+ reg = <0x08001454 0x4>;
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ clocks = <&osc32k>, <&osc24M>;
+ clock-output-names = "r_ir";
+ };
};
soc {
};
mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun9i-a80-mmc";
reg = <0x01c0f000 0x1000>;
clocks = <&mmc_config_clk 0>, <&mmc0_clk 0>,
<&mmc0_clk 1>, <&mmc0_clk 2>;
};
mmc1: mmc@01c10000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun9i-a80-mmc";
reg = <0x01c10000 0x1000>;
clocks = <&mmc_config_clk 1>, <&mmc1_clk 0>,
<&mmc1_clk 1>, <&mmc1_clk 2>;
};
mmc2: mmc@01c11000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun9i-a80-mmc";
reg = <0x01c11000 0x1000>;
clocks = <&mmc_config_clk 2>, <&mmc2_clk 0>,
<&mmc2_clk 1>, <&mmc2_clk 2>;
};
mmc3: mmc@01c12000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun9i-a80-mmc";
reg = <0x01c12000 0x1000>;
clocks = <&mmc_config_clk 3>, <&mmc3_clk 0>,
<&mmc3_clk 1>, <&mmc3_clk 2>;
clocks = <&apb0_gates 5>;
gpio-controller;
interrupt-controller;
- #interrupt-cells = <2>;
+ #interrupt-cells = <3>;
#size-cells = <0>;
#gpio-cells = <3>;
mmc2_8bit_pins: mmc2_8bit {
allwinner,pins = "PC6", "PC7", "PC8", "PC9",
"PC10", "PC11", "PC12",
- "PC13", "PC14", "PC15";
+ "PC13", "PC14", "PC15",
+ "PC16";
allwinner,function = "mmc2";
allwinner,drive = <SUN4I_PINCTRL_30_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
};
+ apbs_rst: reset@080014b0 {
+ reg = <0x080014b0 0x4>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ #reset-cells = <1>;
+ };
+
+ nmi_intc: interrupt-controller@080015a0 {
+ compatible = "allwinner,sun9i-a80-nmi";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x080015a0 0xc>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ r_ir: ir@08002000 {
+ compatible = "allwinner,sun5i-a13-ir";
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_ir_pins>;
+ clocks = <&apbs_gates 1>, <&r_ir_clk>;
+ clock-names = "apb", "ir";
+ resets = <&apbs_rst 1>;
+ reg = <0x08002000 0x40>;
+ status = "disabled";
+ };
+
r_uart: serial@08002800 {
compatible = "snps,dw-apb-uart";
reg = <0x08002800 0x400>;
interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&osc24M>;
+ clocks = <&apbs_gates 4>;
+ resets = <&apbs_rst 4>;
status = "disabled";
};
+
+ r_pio: pinctrl@08002c00 {
+ compatible = "allwinner,sun9i-a80-r-pinctrl";
+ reg = <0x08002c00 0x400>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apbs_gates 0>;
+ resets = <&apbs_rst 0>;
+ gpio-controller;
+ interrupt-controller;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #gpio-cells = <3>;
+
+ r_ir_pins: r_ir {
+ allwinner,pins = "PL6";
+ allwinner,function = "s_cir_rx";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ r_rsb_pins: r_rsb {
+ allwinner,pins = "PN0", "PN1";
+ allwinner,function = "s_rsb";
+ allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+ };
+
+ r_rsb: i2c@08003400 {
+ compatible = "allwinner,sun8i-a23-rsb";
+ reg = <0x08003400 0x400>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apbs_gates 3>;
+ clock-frequency = <3000000>;
+ resets = <&apbs_rst 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_rsb_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
};
--- /dev/null
+/*
+ * Copyright 2015 - Marcus Cooper <codekipper@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-common-regulators.dtsi"
+
+/ {
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
voltage = <400000>;
};
};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins>;
+ status = "okay";
+};
#define SUNXI_AD_DA_BASE 0x01c22c00
#define SUNXI_KEYPAD_BASE 0x01c23000
#define SUNXI_TZPC_BASE 0x01c23400
+
+#if defined(CONFIG_MACH_SUN8I_A83T) || defined(CONFIG_MACH_SUN8I_H3)
+/* SID address space starts at 0x01c1400, but e-fuse is at offset 0x200 */
+#define SUNXI_SID_BASE 0x01c14200
+#else
#define SUNXI_SID_BASE 0x01c23800
+#endif
+
#define SUNXI_SJTAG_BASE 0x01c23c00
#define SUNXI_TP_BASE 0x01c25000
void return_to_fel(uint32_t lr, uint32_t sp);
/* Board / SoC level designware gmac init */
-int sunxi_gmac_initialize(bd_t *bis);
+#if !defined CONFIG_SPL_BUILD && defined CONFIG_SUNXI_GMAC
+void eth_init_board(void);
+#else
+static inline void eth_init_board(void) {}
+#endif
#endif
---help---
See USB1_VBUS_PIN help text.
+config USB3_VBUS_PIN
+ string "Vbus enable pin for usb3 (ehci2)"
+ default ""
+ ---help---
+ See USB1_VBUS_PIN help text.
+
config I2C0_ENABLE
bool "Enable I2C/TWI controller 0"
default y if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
F: configs/ba10_tv_box_defconfig
F: configs/Chuwi_V7_CW0825_defconfig
F: configs/Cubieboard_defconfig
+F: configs/dserve_dsrv9703c_defconfig
F: configs/Hyundai_A7HD_defconfig
F: configs/inet1_defconfig
F: configs/inet97fv2_defconfig
F: configs/Auxtek-T003_defconfig
F: configs/Auxtek-T004_defconfig
F: configs/CHIP_defconfig
+F: configs/difrnce_dit4350_defconfig
F: configs/Empire_electronix_d709_defconfig
F: configs/inet98v_rev2_defconfig
F: configs/mk802_a10s_defconfig
F: configs/UTOO_P66_defconfig
F: configs/Wobo_i5_defconfig
F: include/configs/sun6i.h
+F: configs/colorfly_e708_q1_defconfig
F: configs/CSQ_CS908_defconfig
F: configs/Mele_A1000G_quad_defconfig
F: configs/Mele_M9_defconfig
F: include/configs/sun8i.h
F: configs/ga10h_v1_1_defconfig
F: configs/gt90h_v4_defconfig
+F: configs/orangepi_2_defconfig
F: configs/orangepi_pc_defconfig
F: configs/orangepi_plus_defconfig
+F: configs/polaroid_mid2809pxe04_defconfig
F: configs/q8_a23_tablet_800x480_defconfig
F: configs/q8_a33_tablet_800x480_defconfig
F: configs/q8_a33_tablet_1024x600_defconfig
F: configs/Cubieboard2_defconfig
F: configs/Cubietruck_defconfig
+CUBIETRUCK-PLUS BOARD
+M: Chen-Yu Tsai <wens@csie.org>
+S: Maintained
+F: configs/Cubietruck_plus_defconfig
+
GEMEI-G9 TABLET
M: Priit Laes <plaes@plaes.org>
S: Maintained
S: Maintained
F: configs/Hummingbird_A31_defconfig
+ICnova-A20-SWAC BOARD
+M: Stefan Roese <sr@denx.de>
+S: Maintained
+F: configs/icnova-a20-swac_defconfig
+
+ITEAD IBOX BOARD
+M: Marcus Cooper <codekipper@gmail.com>
+S: Maintained
+F: configs/Itead_Ibox_A20_defconfig
+
INET 3F BOARD
M: Paul Kocialkowski <contact@paulk.fr>
S: Maintained
S: Maintained
F: configs/MSI_Primo81_defconfig
+SINLINX SINA31s BOARD
+M: Chen-Yu Tsai <wens@csie.org>
+S: Maintained
+F: configs/Sinlinx_SinA31s_defconfig
+W: http://linux-sunxi.org/Sinlinx_SinA31s
+
SINLINX SINA33 BOARD
M: Chen-Yu Tsai <wens@csie.org>
S: Maintained
M: Paul Kocialkowski <contact@paulk.fr>
S: Maintained
F: configs/Yones_Toptech_BD1078_defconfig
+
+YONES TOPTECH BS1078 V2 BOARD
+M: Peter Korsgaard <peter@korsgaard.com>
+S: Maintained
+F: configs/Yones_Toptech_BS1078_V2_defconfig
void scsi_init(void)
{
- printf("SUNXI SCSI INIT\n");
-#ifdef CONFIG_SATAPWR
- gpio_request(CONFIG_SATAPWR, "satapwr");
- gpio_direction_output(CONFIG_SATAPWR, 1);
- /* Give attached sata device time to power-up to avoid link timeouts */
- mdelay(500);
-#endif
-
if (sunxi_ahci_phy_init(SUNXI_SATA_BASE) < 0)
return;
if (ret)
return ret;
+#ifdef CONFIG_SATAPWR
+ gpio_request(CONFIG_SATAPWR, "satapwr");
+ gpio_direction_output(CONFIG_SATAPWR, 1);
+#endif
+#ifdef CONFIG_MACPWR
+ gpio_request(CONFIG_MACPWR, "macpwr");
+ gpio_direction_output(CONFIG_MACPWR, 1);
+#endif
+
/* Uses dm gpio code so do this here and not in i2c_init_board() */
return soft_i2c_board_init();
}
}
#endif
-#ifdef CONFIG_OF_BOARD_SETUP
int ft_board_setup(void *blob, bd_t *bd)
{
+ int __maybe_unused r;
+
#ifdef CONFIG_VIDEO_DT_SIMPLEFB
- return sunxi_simplefb_setup(blob);
+ r = sunxi_simplefb_setup(blob);
+ if (r)
+ return r;
#endif
+ return 0;
}
-#endif /* CONFIG_OF_BOARD_SETUP */
#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
-int sunxi_gmac_initialize(bd_t *bis)
+void eth_init_board(void)
{
int pin;
struct sunxi_ccm_reg *const ccm =
for (pin = SUNXI_GPA(26); pin <= SUNXI_GPA(27); pin++)
sunxi_gpio_set_cfgpin(pin, SUN6I_GPA_GMAC);
#endif
-
-#ifdef CONFIG_DM_ETH
- return 0;
-#else
-# ifdef CONFIG_RGMII
- return designware_initialize(SUNXI_GMAC_BASE, PHY_INTERFACE_MODE_RGMII);
-# elif defined CONFIG_GMII
- return designware_initialize(SUNXI_GMAC_BASE, PHY_INTERFACE_MODE_GMII);
-# else
- return designware_initialize(SUNXI_GMAC_BASE, PHY_INTERFACE_MODE_MII);
-# endif
-#endif
}
{ BOOT_DEVICE_RAM, "RAM" },
#endif
#ifdef CONFIG_SPL_MMC_SUPPORT
- { BOOT_DEVICE_MMC1, "MMC" },
- { BOOT_DEVICE_MMC2, "MMC" },
- { BOOT_DEVICE_MMC2_2, "MMC" },
+ { BOOT_DEVICE_MMC1, "MMC1" },
+ { BOOT_DEVICE_MMC2, "MMC2" },
+ { BOOT_DEVICE_MMC2_2, "MMC2_2" },
#endif
#ifdef CONFIG_SPL_NAND_SUPPORT
{ BOOT_DEVICE_NAND, "NAND" },
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-olinuxino-lime"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_EMAC,AHCI,SATAPWR=SUNXI_GPC(3)"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun5i-a10s-olinuxino-micro"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_EMAC"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-olinuxino-micro"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=2"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-olinuxino"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=2"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-olinuxino-lime2"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII,AHCI,SATAPWR=SUNXI_GPC(3)"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-olinuxino-lime"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,AHCI,SATAPWR=SUNXI_GPC(3)"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-olinuxino-micro"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,AHCI,SATAPWR=SUNXI_GPB(8)"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-olimex-som-evb"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII,AHCI,SATAPWR=SUNXI_GPC(3)"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-ainol-aw1"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-ampe-a76"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=2"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun5i-a10s-auxtek-t003"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun5i-a10s-auxtek-t004"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-bananapi"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPH(23),AHCI"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-bananapro"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPH(23),AHCI"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DRAM_TIMINGS_DDR3_800E_1066G_1333J=y
# CONFIG_MMC is not set
CONFIG_USB0_VBUS_PIN="PB10"
+CONFIG_VIDEO_COMPOSITE=y
CONFIG_DEFAULT_DEVICE_TREE="sun5i-r8-chip"
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=2"
# CONFIG_CMD_IMLS is not set
CONFIG_CMD_GPIO=y
-CONFIG_AXP_DCDC2_VOLT=1300
CONFIG_AXP_ALDO3_VOLT=3300
CONFIG_AXP_ALDO4_VOLT=3300
CONFIG_USB_MUSB_GADGET=y
CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31s-cs908"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-chuwi-v7-cw0825"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-colombus"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-cubieboard2"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,AHCI,SATAPWR=SUNXI_GPB(8)"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-cubieboard"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_EMAC,AHCI,SATAPWR=SUNXI_GPB(8)"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-cubietruck"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII,AHCI,SATAPWR=SUNXI_GPH(12)"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN8I_A83T=y
+CONFIG_DRAM_CLK=672
+CONFIG_DRAM_ZQ=15355
+CONFIG_DRAM_ODT_EN=y
+CONFIG_MMC0_CD_PIN="PF6"
+CONFIG_I2C0_ENABLE=y
+CONFIG_AXP_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-a83t-cubietruck-plus"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="RGMII,MACPWR=SUNXI_GPD(20)"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_AXP_DLDO3_VOLT=2500
+CONFIG_AXP_DLDO4_VOLT=3300
CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-empire-electronix-d709"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=2"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-hummingbird"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPA(21)"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-hyundai-a7hd"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN7I=y
+CONFIG_DRAM_CLK=480
+CONFIG_MMC0_CD_PIN="PH1"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-itead-ibox"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,AHCI,SATAPWR=SUNXI_GPB(8)"
+#CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_EMAC,AHCI,SATAPWR=SUNXI_GPB(8)"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-lamobo-r1"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPH(23),AHCI,SATAPWR=SUNXI_GPB(3)"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-pcduino3-nano"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII,AHCI,SATAPWR=SUNXI_GPH(2)"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-pcduino3"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,AHCI,SATAPWR=SUNXI_GPH(2)"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-pcduino"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_EMAC"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-mk808c"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-primo73"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31s-primo81"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-marsboard"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_EMAC,AHCI"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-mele-a1000g-quad"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-a1000"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_EMAC,MACPWR=SUNXI_GPH(15),AHCI"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-i7"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-m3"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-m5"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,AHCI,STATUSLED=234"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-m9"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-mini-xplus"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-orangepi"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPH(23),AHCI"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-orangepi-mini"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPH(23),AHCI"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN6I=y
+CONFIG_DRAM_CLK=432
+CONFIG_DRAM_ZQ=251
+CONFIG_MMC0_CD_PIN="PA4"
+CONFIG_MMC3_PINS="PC"
+CONFIG_MMC_SUNXI_SLOT_EXTRA=3
+CONFIG_USB1_VBUS_PIN=""
+CONFIG_USB2_VBUS_PIN=""
+CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31s-sina31s"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_AXP_DLDO1_VOLT=3300
+CONFIG_USB_EHCI_HCD=y
CONFIG_DEFAULT_DEVICE_TREE="sun8i-a33-sinlinx-sina33"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31s-sinovoip-bpi-m2"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_AXP_DCDC1_VOLT=3000
CONFIG_AXP_DCDC5_VOLT=1200
-CONFIG_AXP_ALDO2_VOLT=0
-CONFIG_AXP_ALDO3_VOLT=0
CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-utoo-p66"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-wexler-tab7200"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-wits-pro-a20-dkt"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII,AHCI"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun5i-a10s-wobo-i5"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-yones-toptech-bd1078"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN6I=y
+CONFIG_DRAM_CLK=420
+CONFIG_DRAM_ZQ=251
+CONFIG_MMC0_CD_PIN="PA8"
+CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
+CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_USB0_ID_DET="PA15"
+CONFIG_AXP_GPIO=y
+CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:24,pclk_khz:70000,le:120,ri:180,up:17,lo:15,hs:20,vs:3,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_DCLK_PHASE=0
+CONFIG_VIDEO_LCD_BL_EN="PA25"
+CONFIG_VIDEO_LCD_BL_PWM="PH13"
+CONFIG_VIDEO_LCD_PANEL_LVDS=y
+CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31s-yones-toptech-bs1078-v2"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+CONFIG_AXP_DLDO1_VOLT=3300
+CONFIG_USB_MUSB_HOST=y
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-ba10-tvbox"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_EMAC"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN6I=y
+CONFIG_DRAM_CLK=432
+CONFIG_DRAM_ZQ=251
+CONFIG_MMC0_CD_PIN="PA8"
+CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
+CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_USB0_ID_DET="PA15"
+CONFIG_AXP_GPIO=y
+CONFIG_VIDEO_LCD_MODE="x:800,y:1280,depth:24,pclk_khz:64000,le:20,ri:34,up:1,lo:16,hs:10,vs:1,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_DCLK_PHASE=0
+CONFIG_VIDEO_LCD_BL_EN="PA25"
+CONFIG_VIDEO_LCD_BL_PWM="PH13"
+CONFIG_VIDEO_LCD_PANEL_LVDS=y
+CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31s-colorfly-e708-q1"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+CONFIG_AXP_DLDO1_VOLT=3300
+CONFIG_AXP_DLDO2_VOLT=1800
+CONFIG_USB_MUSB_HOST=y
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN5I=y
+CONFIG_DRAM_CLK=408
+CONFIG_MMC0_CD_PIN="PG0"
+CONFIG_USB0_VBUS_PIN="PG12"
+CONFIG_USB0_VBUS_DET="PG1"
+CONFIG_USB0_ID_DET="PG2"
+CONFIG_AXP_GPIO=y
+# CONFIG_VIDEO_HDMI is not set
+CONFIG_VIDEO_LCD_MODE="x:480,y:272,depth:18,pclk_khz:12000,le:1,ri:43,up:1,lo:12,hs:1,vs:1,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_POWER="AXP0-0"
+CONFIG_VIDEO_LCD_BL_EN="AXP0-1"
+CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-difrnce-dit4350"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=2"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+CONFIG_USB_MUSB_HOST=y
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN4I=y
+CONFIG_DRAM_CLK=360
+CONFIG_MMC0_CD_PIN="PH1"
+CONFIG_USB0_VBUS_PIN="PB9"
+CONFIG_USB0_VBUS_DET="PH5"
+CONFIG_USB0_ID_DET="PH4"
+CONFIG_VIDEO_LCD_MODE="x:1024,y:768,depth:18,pclk_khz:80000,le:479,ri:544,up:5,lo:26,hs:1,vs:1,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_DCLK_PHASE=0
+CONFIG_VIDEO_LCD_POWER="PH8"
+CONFIG_VIDEO_LCD_BL_EN="PH7"
+CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_VIDEO_LCD_PANEL_LVDS=y
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-dserve-dsrv9703c"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+CONFIG_USB_MUSB_HOST=y
CONFIG_DEFAULT_DEVICE_TREE="sun8i-a33-ga10h-v1.1"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun8i-a23-gt90h-v4"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-i12-tvbox"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,MACPWR=SUNXI_GPH(21)"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-inet-3f"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-inet-3w"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-inet-86vs"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN7I=y
+CONFIG_DRAM_CLK=384
+CONFIG_OLD_SUNXI_KERNEL_COMPAT=y
+CONFIG_MMC0_CD_PIN="PI5"
+CONFIG_USB0_VBUS_PIN="PG11"
+CONFIG_USB0_VBUS_DET="PH7"
+CONFIG_USB1_VBUS_PIN="PG10"
+CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:24,pclk_khz:33000,le:45,ri:209,up:22,lo:22,hs:1,vs:1,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_POWER="PH22"
+CONFIG_VIDEO_LCD_PANEL_LVDS=y
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-icnova-swac"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,CMD_BMP,CMD_UNZIP"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-inet1"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-inet97fv2"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-inet-98v-rev2"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=2"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-inet9f-rev03"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-jesurun-q5"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_EMAC,MACPWR=SUNXI_GPH(19)"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-mixtile-loftq"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPA(21)"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun5i-a10s-mk802"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-mk802"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="USB_EHCI"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-mk802ii"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN8I_H3=y
+CONFIG_DRAM_CLK=672
+CONFIG_DRAM_ZQ=3881979
+CONFIG_DRAM_ODT_EN=y
+CONFIG_MMC0_CD_PIN="PF6"
+# CONFIG_VIDEO is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-orangepi-2"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+CONFIG_SY8106A_POWER=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB1_VBUS_PIN="PG13"
CONFIG_CMD_GPIO=y
CONFIG_SY8106A_POWER=y
CONFIG_USB_EHCI_HCD=y
+CONFIG_USB1_VBUS_PIN=""
+CONFIG_USB2_VBUS_PIN=""
+CONFIG_USB3_VBUS_PIN=""
CONFIG_DRAM_CLK=672
CONFIG_DRAM_ZQ=3881979
CONFIG_DRAM_ODT_EN=y
+CONFIG_MMC0_CD_PIN="PF6"
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
# CONFIG_VIDEO is not set
CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-orangepi-plus"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_CMD_GPIO=y
CONFIG_SY8106A_POWER=y
CONFIG_USB_EHCI_HCD=y
+CONFIG_USB1_VBUS_PIN="PG13"
+CONFIG_SYS_EXTRA_OPTIONS="SATAPWR=SUNXI_GPG(11)"
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN8I_A23=y
+CONFIG_DRAM_CLK=432
+CONFIG_DRAM_ZQ=63351
+CONFIG_MMC0_CD_PIN="PB4"
+CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
+CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_USB0_ID_DET="PH8"
+CONFIG_AXP_GPIO=y
+CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:36,ri:210,up:18,lo:22,hs:10,vs:5,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_DCLK_PHASE=0
+CONFIG_VIDEO_LCD_POWER="PH7"
+CONFIG_VIDEO_LCD_BL_EN="PH6"
+CONFIG_VIDEO_LCD_BL_PWM="PH0"
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-a23-polaroid-mid2809pxe04"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+CONFIG_AXP_DLDO1_VOLT=3300
+CONFIG_USB_MUSB_HOST=y
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-pov-protab2-ips9"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-q8-tablet"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=2"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun8i-a23-q8-tablet"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun8i-a33-q8-tablet"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun8i-a33-q8-tablet"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DEFAULT_DEVICE_TREE="sun5i-a10s-r7-tv-dongle"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-gemei-g9"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
-CONFIG_OF_BOARD_SETUP=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
start = 'L' - 'A';
no_banks = 2; /* L & M */
} else if (fdt_node_check_compatible(gd->fdt_blob, parent->of_offset,
- "allwinner,sun8i-a23-r-pinctrl") == 0) {
+ "allwinner,sun8i-a23-r-pinctrl") == 0 ||
+ fdt_node_check_compatible(gd->fdt_blob, parent->of_offset,
+ "allwinner,sun8i-a83t-r-pinctrl") == 0 ||
+ fdt_node_check_compatible(gd->fdt_blob, parent->of_offset,
+ "allwinner,sun8i-h3-r-pinctrl") == 0) {
start = 'L' - 'A';
no_banks = 1; /* L only */
+ } else if (fdt_node_check_compatible(gd->fdt_blob, parent->of_offset,
+ "allwinner,sun9i-a80-r-pinctrl") == 0) {
+ start = 'L' - 'A';
+ no_banks = 3; /* L, M & N */
} else {
start = 0;
no_banks = SUNXI_GPIO_BANKS;
{ .compatible = "allwinner,sun7i-a20-pinctrl" },
{ .compatible = "allwinner,sun8i-a23-pinctrl" },
{ .compatible = "allwinner,sun8i-a33-pinctrl" },
+ { .compatible = "allwinner,sun8i-a83t-pinctrl", },
+ { .compatible = "allwinner,sun8i-h3-pinctrl" },
{ .compatible = "allwinner,sun9i-a80-pinctrl" },
{ .compatible = "allwinner,sun6i-a31-r-pinctrl" },
{ .compatible = "allwinner,sun8i-a23-r-pinctrl" },
+ { .compatible = "allwinner,sun8i-a83t-r-pinctrl" },
+ { .compatible = "allwinner,sun8i-h3-r-pinctrl", },
+ { .compatible = "allwinner,sun9i-a80-r-pinctrl", },
{ }
};
#include <dm.h>
#include "ehci.h"
+#ifdef CONFIG_SUNXI_GEN_SUN4I
+#define BASE_DIST 0x8000
+#define AHB_CLK_DIST 2
+#else
+#define BASE_DIST 0x1000
+#define AHB_CLK_DIST 1
+#endif
+
struct ehci_sunxi_priv {
struct ehci_ctrl ehci;
int ahb_gate_mask; /* Mask of ahb_gate0 clk gate bits for this hcd */
#ifdef CONFIG_MACH_SUN8I_H3
priv->ahb_gate_mask |= 1 << AHB_GATE_OFFSET_USB_OHCI0;
#endif
- priv->phy_index = ((u32)hccr - SUNXI_USB1_BASE) / 0x1000 + 1;
- priv->ahb_gate_mask <<= priv->phy_index - 1;
+ priv->phy_index = ((u32)hccr - SUNXI_USB1_BASE) / BASE_DIST;
+ priv->ahb_gate_mask <<= priv->phy_index * AHB_CLK_DIST;
+ priv->phy_index++; /* Non otg phys start at 1 */
setbits_le32(&ccm->ahb_gate0, priv->ahb_gate_mask);
#ifdef CONFIG_SUNXI_GEN_SUN6I
#include <usb.h>
#include "ohci.h"
+#ifdef CONFIG_SUNXI_GEN_SUN4I
+#define BASE_DIST 0x8000
+#define AHB_CLK_DIST 2
+#else
+#define BASE_DIST 0x1000
+#define AHB_CLK_DIST 1
+#endif
+
struct ohci_sunxi_priv {
ohci_t ohci;
int ahb_gate_mask; /* Mask of ahb_gate0 clk gate bits for this hcd */
priv->ahb_gate_mask |= 1 << AHB_GATE_OFFSET_USB_EHCI0;
#endif
priv->usb_gate_mask = CCM_USB_CTRL_OHCI0_CLK;
- priv->phy_index = ((u32)regs - (SUNXI_USB1_BASE + 0x400)) / 0x1000 + 1;
- priv->ahb_gate_mask <<= priv->phy_index - 1;
- priv->usb_gate_mask <<= priv->phy_index - 1;
+ priv->phy_index = ((u32)regs - (SUNXI_USB1_BASE + 0x400)) / BASE_DIST;
+ priv->ahb_gate_mask <<= priv->phy_index * AHB_CLK_DIST;
+ priv->usb_gate_mask <<= priv->phy_index;
+ priv->phy_index++; /* Non otg phys start at 1 */
setbits_le32(&ccm->ahb_gate0, priv->ahb_gate_mask);
setbits_le32(&ccm->usb_clk_cfg, priv->usb_gate_mask);
(struct sunxi_lcdc_reg *)SUNXI_LCD0_BASE;
int bp, clk_delay, clk_div, clk_double, pin, total, val;
+#if defined CONFIG_MACH_SUN8I && defined CONFIG_VIDEO_LCD_IF_LVDS
+ for (pin = SUNXI_GPD(18); pin <= SUNXI_GPD(27); pin++) {
+#else
for (pin = SUNXI_GPD(0); pin <= SUNXI_GPD(27); pin++) {
+#endif
#ifdef CONFIG_VIDEO_LCD_IF_PARALLEL
sunxi_gpio_set_cfgpin(pin, SUNXI_GPD_LCD0);
#endif
#define CONFIG_PHY_GIGE /* GMAC can use gigabit PHY */
#define CONFIG_PHY_ADDR 1
#define CONFIG_MII /* MII PHY management */
+#define CONFIG_PHY_REALTEK
#endif
#ifdef CONFIG_USB_EHCI_HCD
--- /dev/null
+/*
+ * Copyright 2015 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef __DT_BINDINGS_CLOCK_SUN4I_A10_PLL2_H_
+#define __DT_BINDINGS_CLOCK_SUN4I_A10_PLL2_H_
+
+#define SUN4I_A10_PLL2_1X 0
+#define SUN4I_A10_PLL2_2X 1
+#define SUN4I_A10_PLL2_4X 2
+#define SUN4I_A10_PLL2_8X 3
+
+#endif /* __DT_BINDINGS_CLOCK_SUN4I_A10_PLL2_H_ */
#ifndef _DT_BINDINGS_INPUT_INPUT_H
#define _DT_BINDINGS_INPUT_INPUT_H
-#define KEY_RESERVED 0
-#define KEY_ESC 1
-#define KEY_1 2
-#define KEY_2 3
-#define KEY_3 4
-#define KEY_4 5
-#define KEY_5 6
-#define KEY_6 7
-#define KEY_7 8
-#define KEY_8 9
-#define KEY_9 10
-#define KEY_0 11
-#define KEY_MINUS 12
-#define KEY_EQUAL 13
-#define KEY_BACKSPACE 14
-#define KEY_TAB 15
-#define KEY_Q 16
-#define KEY_W 17
-#define KEY_E 18
-#define KEY_R 19
-#define KEY_T 20
-#define KEY_Y 21
-#define KEY_U 22
-#define KEY_I 23
-#define KEY_O 24
-#define KEY_P 25
-#define KEY_LEFTBRACE 26
-#define KEY_RIGHTBRACE 27
-#define KEY_ENTER 28
-#define KEY_LEFTCTRL 29
-#define KEY_A 30
-#define KEY_S 31
-#define KEY_D 32
-#define KEY_F 33
-#define KEY_G 34
-#define KEY_H 35
-#define KEY_J 36
-#define KEY_K 37
-#define KEY_L 38
-#define KEY_SEMICOLON 39
-#define KEY_APOSTROPHE 40
-#define KEY_GRAVE 41
-#define KEY_LEFTSHIFT 42
-#define KEY_BACKSLASH 43
-#define KEY_Z 44
-#define KEY_X 45
-#define KEY_C 46
-#define KEY_V 47
-#define KEY_B 48
-#define KEY_N 49
-#define KEY_M 50
-#define KEY_COMMA 51
-#define KEY_DOT 52
-#define KEY_SLASH 53
-#define KEY_RIGHTSHIFT 54
-#define KEY_KPASTERISK 55
-#define KEY_LEFTALT 56
-#define KEY_SPACE 57
-#define KEY_CAPSLOCK 58
-#define KEY_F1 59
-#define KEY_F2 60
-#define KEY_F3 61
-#define KEY_F4 62
-#define KEY_F5 63
-#define KEY_F6 64
-#define KEY_F7 65
-#define KEY_F8 66
-#define KEY_F9 67
-#define KEY_F10 68
-#define KEY_NUMLOCK 69
-#define KEY_SCROLLLOCK 70
-#define KEY_KP7 71
-#define KEY_KP8 72
-#define KEY_KP9 73
-#define KEY_KPMINUS 74
-#define KEY_KP4 75
-#define KEY_KP5 76
-#define KEY_KP6 77
-#define KEY_KPPLUS 78
-#define KEY_KP1 79
-#define KEY_KP2 80
-#define KEY_KP3 81
-#define KEY_KP0 82
-#define KEY_KPDOT 83
-
-#define KEY_ZENKAKUHANKAKU 85
-#define KEY_102ND 86
-#define KEY_F11 87
-#define KEY_F12 88
-#define KEY_RO 89
-#define KEY_KATAKANA 90
-#define KEY_HIRAGANA 91
-#define KEY_HENKAN 92
-#define KEY_KATAKANAHIRAGANA 93
-#define KEY_MUHENKAN 94
-#define KEY_KPJPCOMMA 95
-#define KEY_KPENTER 96
-#define KEY_RIGHTCTRL 97
-#define KEY_KPSLASH 98
-#define KEY_SYSRQ 99
-#define KEY_RIGHTALT 100
-#define KEY_LINEFEED 101
-#define KEY_HOME 102
-#define KEY_UP 103
-#define KEY_PAGEUP 104
-#define KEY_LEFT 105
-#define KEY_RIGHT 106
-#define KEY_END 107
-#define KEY_DOWN 108
-#define KEY_PAGEDOWN 109
-#define KEY_INSERT 110
-#define KEY_DELETE 111
-#define KEY_MACRO 112
-#define KEY_MUTE 113
-#define KEY_VOLUMEDOWN 114
-#define KEY_VOLUMEUP 115
-#define KEY_POWER 116 /* SC System Power Down */
-#define KEY_KPEQUAL 117
-#define KEY_KPPLUSMINUS 118
-#define KEY_PAUSE 119
-#define KEY_SCALE 120 /* AL Compiz Scale (Expose) */
-
-#define KEY_KPCOMMA 121
-#define KEY_HANGEUL 122
-#define KEY_HANGUEL KEY_HANGEUL
-#define KEY_HANJA 123
-#define KEY_YEN 124
-#define KEY_LEFTMETA 125
-#define KEY_RIGHTMETA 126
-#define KEY_COMPOSE 127
-
-#define KEY_STOP 128 /* AC Stop */
-#define KEY_AGAIN 129
-#define KEY_PROPS 130 /* AC Properties */
-#define KEY_UNDO 131 /* AC Undo */
-#define KEY_FRONT 132
-#define KEY_COPY 133 /* AC Copy */
-#define KEY_OPEN 134 /* AC Open */
-#define KEY_PASTE 135 /* AC Paste */
-#define KEY_FIND 136 /* AC Search */
-#define KEY_CUT 137 /* AC Cut */
-#define KEY_HELP 138 /* AL Integrated Help Center */
-#define KEY_MENU 139 /* Menu (show menu) */
-#define KEY_CALC 140 /* AL Calculator */
-#define KEY_SETUP 141
-#define KEY_SLEEP 142 /* SC System Sleep */
-#define KEY_WAKEUP 143 /* System Wake Up */
-#define KEY_FILE 144 /* AL Local Machine Browser */
-#define KEY_SENDFILE 145
-#define KEY_DELETEFILE 146
-#define KEY_XFER 147
-#define KEY_PROG1 148
-#define KEY_PROG2 149
-#define KEY_WWW 150 /* AL Internet Browser */
-#define KEY_MSDOS 151
-#define KEY_COFFEE 152 /* AL Terminal Lock/Screensaver */
-#define KEY_SCREENLOCK KEY_COFFEE
-#define KEY_DIRECTION 153
-#define KEY_CYCLEWINDOWS 154
-#define KEY_MAIL 155
-#define KEY_BOOKMARKS 156 /* AC Bookmarks */
-#define KEY_COMPUTER 157
-#define KEY_BACK 158 /* AC Back */
-#define KEY_FORWARD 159 /* AC Forward */
-#define KEY_CLOSECD 160
-#define KEY_EJECTCD 161
-#define KEY_EJECTCLOSECD 162
-#define KEY_NEXTSONG 163
-#define KEY_PLAYPAUSE 164
-#define KEY_PREVIOUSSONG 165
-#define KEY_STOPCD 166
-#define KEY_RECORD 167
-#define KEY_REWIND 168
-#define KEY_PHONE 169 /* Media Select Telephone */
-#define KEY_ISO 170
-#define KEY_CONFIG 171 /* AL Consumer Control Configuration */
-#define KEY_HOMEPAGE 172 /* AC Home */
-#define KEY_REFRESH 173 /* AC Refresh */
-#define KEY_EXIT 174 /* AC Exit */
-#define KEY_MOVE 175
-#define KEY_EDIT 176
-#define KEY_SCROLLUP 177
-#define KEY_SCROLLDOWN 178
-#define KEY_KPLEFTPAREN 179
-#define KEY_KPRIGHTPAREN 180
-#define KEY_NEW 181 /* AC New */
-#define KEY_REDO 182 /* AC Redo/Repeat */
-
-#define KEY_F13 183
-#define KEY_F14 184
-#define KEY_F15 185
-#define KEY_F16 186
-#define KEY_F17 187
-#define KEY_F18 188
-#define KEY_F19 189
-#define KEY_F20 190
-#define KEY_F21 191
-#define KEY_F22 192
-#define KEY_F23 193
-#define KEY_F24 194
-
-#define KEY_PLAYCD 200
-#define KEY_PAUSECD 201
-#define KEY_PROG3 202
-#define KEY_PROG4 203
-#define KEY_DASHBOARD 204 /* AL Dashboard */
-#define KEY_SUSPEND 205
-#define KEY_CLOSE 206 /* AC Close */
-#define KEY_PLAY 207
-#define KEY_FASTFORWARD 208
-#define KEY_BASSBOOST 209
-#define KEY_PRINT 210 /* AC Print */
-#define KEY_HP 211
-#define KEY_CAMERA 212
-#define KEY_SOUND 213
-#define KEY_QUESTION 214
-#define KEY_EMAIL 215
-#define KEY_CHAT 216
-#define KEY_SEARCH 217
-#define KEY_CONNECT 218
-#define KEY_FINANCE 219 /* AL Checkbook/Finance */
-#define KEY_SPORT 220
-#define KEY_SHOP 221
-#define KEY_ALTERASE 222
-#define KEY_CANCEL 223 /* AC Cancel */
-#define KEY_BRIGHTNESSDOWN 224
-#define KEY_BRIGHTNESSUP 225
-#define KEY_MEDIA 226
-
-#define KEY_SWITCHVIDEOMODE 227 /* Cycle between available video
- outputs (Monitor/LCD/TV-out/etc) */
-#define KEY_KBDILLUMTOGGLE 228
-#define KEY_KBDILLUMDOWN 229
-#define KEY_KBDILLUMUP 230
-
-#define KEY_SEND 231 /* AC Send */
-#define KEY_REPLY 232 /* AC Reply */
-#define KEY_FORWARDMAIL 233 /* AC Forward Msg */
-#define KEY_SAVE 234 /* AC Save */
-#define KEY_DOCUMENTS 235
-
-#define KEY_BATTERY 236
-
-#define KEY_BLUETOOTH 237
-#define KEY_WLAN 238
-#define KEY_UWB 239
-
-#define KEY_UNKNOWN 240
-
-#define KEY_VIDEO_NEXT 241 /* drive next video source */
-#define KEY_VIDEO_PREV 242 /* drive previous video source */
-#define KEY_BRIGHTNESS_CYCLE 243 /* brightness up, after max is min */
-#define KEY_BRIGHTNESS_ZERO 244 /* brightness off, use ambient */
-#define KEY_DISPLAY_OFF 245 /* display device to off state */
-
-#define KEY_WIMAX 246
-#define KEY_RFKILL 247 /* Key that controls all radios */
-
-#define KEY_MICMUTE 248 /* Mute / unmute the microphone */
-
-/* Code 255 is reserved for special needs of AT keyboard driver */
-
-#define BTN_MISC 0x100
-#define BTN_0 0x100
-#define BTN_1 0x101
-#define BTN_2 0x102
-#define BTN_3 0x103
-#define BTN_4 0x104
-#define BTN_5 0x105
-#define BTN_6 0x106
-#define BTN_7 0x107
-#define BTN_8 0x108
-#define BTN_9 0x109
-
-#define BTN_MOUSE 0x110
-#define BTN_LEFT 0x110
-#define BTN_RIGHT 0x111
-#define BTN_MIDDLE 0x112
-#define BTN_SIDE 0x113
-#define BTN_EXTRA 0x114
-#define BTN_FORWARD 0x115
-#define BTN_BACK 0x116
-#define BTN_TASK 0x117
-
-#define BTN_JOYSTICK 0x120
-#define BTN_TRIGGER 0x120
-#define BTN_THUMB 0x121
-#define BTN_THUMB2 0x122
-#define BTN_TOP 0x123
-#define BTN_TOP2 0x124
-#define BTN_PINKIE 0x125
-#define BTN_BASE 0x126
-#define BTN_BASE2 0x127
-#define BTN_BASE3 0x128
-#define BTN_BASE4 0x129
-#define BTN_BASE5 0x12a
-#define BTN_BASE6 0x12b
-#define BTN_DEAD 0x12f
-
-#define BTN_GAMEPAD 0x130
-#define BTN_SOUTH 0x130
-#define BTN_A BTN_SOUTH
-#define BTN_EAST 0x131
-#define BTN_B BTN_EAST
-#define BTN_C 0x132
-#define BTN_NORTH 0x133
-#define BTN_X BTN_NORTH
-#define BTN_WEST 0x134
-#define BTN_Y BTN_WEST
-#define BTN_Z 0x135
-#define BTN_TL 0x136
-#define BTN_TR 0x137
-#define BTN_TL2 0x138
-#define BTN_TR2 0x139
-#define BTN_SELECT 0x13a
-#define BTN_START 0x13b
-#define BTN_MODE 0x13c
-#define BTN_THUMBL 0x13d
-#define BTN_THUMBR 0x13e
-
-#define BTN_DIGI 0x140
-#define BTN_TOOL_PEN 0x140
-#define BTN_TOOL_RUBBER 0x141
-#define BTN_TOOL_BRUSH 0x142
-#define BTN_TOOL_PENCIL 0x143
-#define BTN_TOOL_AIRBRUSH 0x144
-#define BTN_TOOL_FINGER 0x145
-#define BTN_TOOL_MOUSE 0x146
-#define BTN_TOOL_LENS 0x147
-#define BTN_TOOL_QUINTTAP 0x148 /* Five fingers on trackpad */
-#define BTN_TOUCH 0x14a
-#define BTN_STYLUS 0x14b
-#define BTN_STYLUS2 0x14c
-#define BTN_TOOL_DOUBLETAP 0x14d
-#define BTN_TOOL_TRIPLETAP 0x14e
-#define BTN_TOOL_QUADTAP 0x14f /* Four fingers on trackpad */
-
-#define BTN_WHEEL 0x150
-#define BTN_GEAR_DOWN 0x150
-#define BTN_GEAR_UP 0x151
-
-#define KEY_OK 0x160
-#define KEY_SELECT 0x161
-#define KEY_GOTO 0x162
-#define KEY_CLEAR 0x163
-#define KEY_POWER2 0x164
-#define KEY_OPTION 0x165
-#define KEY_INFO 0x166 /* AL OEM Features/Tips/Tutorial */
-#define KEY_TIME 0x167
-#define KEY_VENDOR 0x168
-#define KEY_ARCHIVE 0x169
-#define KEY_PROGRAM 0x16a /* Media Select Program Guide */
-#define KEY_CHANNEL 0x16b
-#define KEY_FAVORITES 0x16c
-#define KEY_EPG 0x16d
-#define KEY_PVR 0x16e /* Media Select Home */
-#define KEY_MHP 0x16f
-#define KEY_LANGUAGE 0x170
-#define KEY_TITLE 0x171
-#define KEY_SUBTITLE 0x172
-#define KEY_ANGLE 0x173
-#define KEY_ZOOM 0x174
-#define KEY_MODE 0x175
-#define KEY_KEYBOARD 0x176
-#define KEY_SCREEN 0x177
-#define KEY_PC 0x178 /* Media Select Computer */
-#define KEY_TV 0x179 /* Media Select TV */
-#define KEY_TV2 0x17a /* Media Select Cable */
-#define KEY_VCR 0x17b /* Media Select VCR */
-#define KEY_VCR2 0x17c /* VCR Plus */
-#define KEY_SAT 0x17d /* Media Select Satellite */
-#define KEY_SAT2 0x17e
-#define KEY_CD 0x17f /* Media Select CD */
-#define KEY_TAPE 0x180 /* Media Select Tape */
-#define KEY_RADIO 0x181
-#define KEY_TUNER 0x182 /* Media Select Tuner */
-#define KEY_PLAYER 0x183
-#define KEY_TEXT 0x184
-#define KEY_DVD 0x185 /* Media Select DVD */
-#define KEY_AUX 0x186
-#define KEY_MP3 0x187
-#define KEY_AUDIO 0x188 /* AL Audio Browser */
-#define KEY_VIDEO 0x189 /* AL Movie Browser */
-#define KEY_DIRECTORY 0x18a
-#define KEY_LIST 0x18b
-#define KEY_MEMO 0x18c /* Media Select Messages */
-#define KEY_CALENDAR 0x18d
-#define KEY_RED 0x18e
-#define KEY_GREEN 0x18f
-#define KEY_YELLOW 0x190
-#define KEY_BLUE 0x191
-#define KEY_CHANNELUP 0x192 /* Channel Increment */
-#define KEY_CHANNELDOWN 0x193 /* Channel Decrement */
-#define KEY_FIRST 0x194
-#define KEY_LAST 0x195 /* Recall Last */
-#define KEY_AB 0x196
-#define KEY_NEXT 0x197
-#define KEY_RESTART 0x198
-#define KEY_SLOW 0x199
-#define KEY_SHUFFLE 0x19a
-#define KEY_BREAK 0x19b
-#define KEY_PREVIOUS 0x19c
-#define KEY_DIGITS 0x19d
-#define KEY_TEEN 0x19e
-#define KEY_TWEN 0x19f
-#define KEY_VIDEOPHONE 0x1a0 /* Media Select Video Phone */
-#define KEY_GAMES 0x1a1 /* Media Select Games */
-#define KEY_ZOOMIN 0x1a2 /* AC Zoom In */
-#define KEY_ZOOMOUT 0x1a3 /* AC Zoom Out */
-#define KEY_ZOOMRESET 0x1a4 /* AC Zoom */
-#define KEY_WORDPROCESSOR 0x1a5 /* AL Word Processor */
-#define KEY_EDITOR 0x1a6 /* AL Text Editor */
-#define KEY_SPREADSHEET 0x1a7 /* AL Spreadsheet */
-#define KEY_GRAPHICSEDITOR 0x1a8 /* AL Graphics Editor */
-#define KEY_PRESENTATION 0x1a9 /* AL Presentation App */
-#define KEY_DATABASE 0x1aa /* AL Database App */
-#define KEY_NEWS 0x1ab /* AL Newsreader */
-#define KEY_VOICEMAIL 0x1ac /* AL Voicemail */
-#define KEY_ADDRESSBOOK 0x1ad /* AL Contacts/Address Book */
-#define KEY_MESSENGER 0x1ae /* AL Instant Messaging */
-#define KEY_DISPLAYTOGGLE 0x1af /* Turn display (LCD) on and off */
-#define KEY_SPELLCHECK 0x1b0 /* AL Spell Check */
-#define KEY_LOGOFF 0x1b1 /* AL Logoff */
-
-#define KEY_DOLLAR 0x1b2
-#define KEY_EURO 0x1b3
-
-#define KEY_FRAMEBACK 0x1b4 /* Consumer - transport controls */
-#define KEY_FRAMEFORWARD 0x1b5
-#define KEY_CONTEXT_MENU 0x1b6 /* GenDesc - system context menu */
-#define KEY_MEDIA_REPEAT 0x1b7 /* Consumer - transport control */
-#define KEY_10CHANNELSUP 0x1b8 /* 10 channels up (10+) */
-#define KEY_10CHANNELSDOWN 0x1b9 /* 10 channels down (10-) */
-#define KEY_IMAGES 0x1ba /* AL Image Browser */
-
-#define KEY_DEL_EOL 0x1c0
-#define KEY_DEL_EOS 0x1c1
-#define KEY_INS_LINE 0x1c2
-#define KEY_DEL_LINE 0x1c3
-
-#define KEY_FN 0x1d0
-#define KEY_FN_ESC 0x1d1
-#define KEY_FN_F1 0x1d2
-#define KEY_FN_F2 0x1d3
-#define KEY_FN_F3 0x1d4
-#define KEY_FN_F4 0x1d5
-#define KEY_FN_F5 0x1d6
-#define KEY_FN_F6 0x1d7
-#define KEY_FN_F7 0x1d8
-#define KEY_FN_F8 0x1d9
-#define KEY_FN_F9 0x1da
-#define KEY_FN_F10 0x1db
-#define KEY_FN_F11 0x1dc
-#define KEY_FN_F12 0x1dd
-#define KEY_FN_1 0x1de
-#define KEY_FN_2 0x1df
-#define KEY_FN_D 0x1e0
-#define KEY_FN_E 0x1e1
-#define KEY_FN_F 0x1e2
-#define KEY_FN_S 0x1e3
-#define KEY_FN_B 0x1e4
-
-#define KEY_BRL_DOT1 0x1f1
-#define KEY_BRL_DOT2 0x1f2
-#define KEY_BRL_DOT3 0x1f3
-#define KEY_BRL_DOT4 0x1f4
-#define KEY_BRL_DOT5 0x1f5
-#define KEY_BRL_DOT6 0x1f6
-#define KEY_BRL_DOT7 0x1f7
-#define KEY_BRL_DOT8 0x1f8
-#define KEY_BRL_DOT9 0x1f9
-#define KEY_BRL_DOT10 0x1fa
-
-#define KEY_NUMERIC_0 0x200 /* used by phones, remote controls, */
-#define KEY_NUMERIC_1 0x201 /* and other keypads */
-#define KEY_NUMERIC_2 0x202
-#define KEY_NUMERIC_3 0x203
-#define KEY_NUMERIC_4 0x204
-#define KEY_NUMERIC_5 0x205
-#define KEY_NUMERIC_6 0x206
-#define KEY_NUMERIC_7 0x207
-#define KEY_NUMERIC_8 0x208
-#define KEY_NUMERIC_9 0x209
-#define KEY_NUMERIC_STAR 0x20a
-#define KEY_NUMERIC_POUND 0x20b
-
-#define KEY_CAMERA_FOCUS 0x210
-#define KEY_WPS_BUTTON 0x211 /* WiFi Protected Setup key */
-
-#define KEY_TOUCHPAD_TOGGLE 0x212 /* Request switch touchpad on or off */
-#define KEY_TOUCHPAD_ON 0x213
-#define KEY_TOUCHPAD_OFF 0x214
-
-#define KEY_CAMERA_ZOOMIN 0x215
-#define KEY_CAMERA_ZOOMOUT 0x216
-#define KEY_CAMERA_UP 0x217
-#define KEY_CAMERA_DOWN 0x218
-#define KEY_CAMERA_LEFT 0x219
-#define KEY_CAMERA_RIGHT 0x21a
-
-#define KEY_ATTENDANT_ON 0x21b
-#define KEY_ATTENDANT_OFF 0x21c
-#define KEY_ATTENDANT_TOGGLE 0x21d /* Attendant call on or off */
-#define KEY_LIGHTS_TOGGLE 0x21e /* Reading light on or off */
-
-#define BTN_DPAD_UP 0x220
-#define BTN_DPAD_DOWN 0x221
-#define BTN_DPAD_LEFT 0x222
-#define BTN_DPAD_RIGHT 0x223
+#include "linux-event-codes.h"
#define MATRIX_KEY(row, col, code) \
((((row) & 0xFF) << 24) | (((col) & 0xFF) << 16) | ((code) & 0xFFFF))
--- /dev/null
+/*
+ * Input event codes
+ *
+ * *** IMPORTANT ***
+ * This file is not only included from C-code but also from devicetree source
+ * files. As such this file MUST only contain comments and defines.
+ *
+ * Copyright (c) 1999-2002 Vojtech Pavlik
+ * Copyright (c) 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+#ifndef _UAPI_INPUT_EVENT_CODES_H
+#define _UAPI_INPUT_EVENT_CODES_H
+
+/*
+ * Device properties and quirks
+ */
+
+#define INPUT_PROP_POINTER 0x00 /* needs a pointer */
+#define INPUT_PROP_DIRECT 0x01 /* direct input devices */
+#define INPUT_PROP_BUTTONPAD 0x02 /* has button(s) under pad */
+#define INPUT_PROP_SEMI_MT 0x03 /* touch rectangle only */
+#define INPUT_PROP_TOPBUTTONPAD 0x04 /* softbuttons at top of pad */
+#define INPUT_PROP_POINTING_STICK 0x05 /* is a pointing stick */
+#define INPUT_PROP_ACCELEROMETER 0x06 /* has accelerometer */
+
+#define INPUT_PROP_MAX 0x1f
+#define INPUT_PROP_CNT (INPUT_PROP_MAX + 1)
+
+/*
+ * Event types
+ */
+
+#define EV_SYN 0x00
+#define EV_KEY 0x01
+#define EV_REL 0x02
+#define EV_ABS 0x03
+#define EV_MSC 0x04
+#define EV_SW 0x05
+#define EV_LED 0x11
+#define EV_SND 0x12
+#define EV_REP 0x14
+#define EV_FF 0x15
+#define EV_PWR 0x16
+#define EV_FF_STATUS 0x17
+#define EV_MAX 0x1f
+#define EV_CNT (EV_MAX+1)
+
+/*
+ * Synchronization events.
+ */
+
+#define SYN_REPORT 0
+#define SYN_CONFIG 1
+#define SYN_MT_REPORT 2
+#define SYN_DROPPED 3
+#define SYN_MAX 0xf
+#define SYN_CNT (SYN_MAX+1)
+
+/*
+ * Keys and buttons
+ *
+ * Most of the keys/buttons are modeled after USB HUT 1.12
+ * (see http://www.usb.org/developers/hidpage).
+ * Abbreviations in the comments:
+ * AC - Application Control
+ * AL - Application Launch Button
+ * SC - System Control
+ */
+
+#define KEY_RESERVED 0
+#define KEY_ESC 1
+#define KEY_1 2
+#define KEY_2 3
+#define KEY_3 4
+#define KEY_4 5
+#define KEY_5 6
+#define KEY_6 7
+#define KEY_7 8
+#define KEY_8 9
+#define KEY_9 10
+#define KEY_0 11
+#define KEY_MINUS 12
+#define KEY_EQUAL 13
+#define KEY_BACKSPACE 14
+#define KEY_TAB 15
+#define KEY_Q 16
+#define KEY_W 17
+#define KEY_E 18
+#define KEY_R 19
+#define KEY_T 20
+#define KEY_Y 21
+#define KEY_U 22
+#define KEY_I 23
+#define KEY_O 24
+#define KEY_P 25
+#define KEY_LEFTBRACE 26
+#define KEY_RIGHTBRACE 27
+#define KEY_ENTER 28
+#define KEY_LEFTCTRL 29
+#define KEY_A 30
+#define KEY_S 31
+#define KEY_D 32
+#define KEY_F 33
+#define KEY_G 34
+#define KEY_H 35
+#define KEY_J 36
+#define KEY_K 37
+#define KEY_L 38
+#define KEY_SEMICOLON 39
+#define KEY_APOSTROPHE 40
+#define KEY_GRAVE 41
+#define KEY_LEFTSHIFT 42
+#define KEY_BACKSLASH 43
+#define KEY_Z 44
+#define KEY_X 45
+#define KEY_C 46
+#define KEY_V 47
+#define KEY_B 48
+#define KEY_N 49
+#define KEY_M 50
+#define KEY_COMMA 51
+#define KEY_DOT 52
+#define KEY_SLASH 53
+#define KEY_RIGHTSHIFT 54
+#define KEY_KPASTERISK 55
+#define KEY_LEFTALT 56
+#define KEY_SPACE 57
+#define KEY_CAPSLOCK 58
+#define KEY_F1 59
+#define KEY_F2 60
+#define KEY_F3 61
+#define KEY_F4 62
+#define KEY_F5 63
+#define KEY_F6 64
+#define KEY_F7 65
+#define KEY_F8 66
+#define KEY_F9 67
+#define KEY_F10 68
+#define KEY_NUMLOCK 69
+#define KEY_SCROLLLOCK 70
+#define KEY_KP7 71
+#define KEY_KP8 72
+#define KEY_KP9 73
+#define KEY_KPMINUS 74
+#define KEY_KP4 75
+#define KEY_KP5 76
+#define KEY_KP6 77
+#define KEY_KPPLUS 78
+#define KEY_KP1 79
+#define KEY_KP2 80
+#define KEY_KP3 81
+#define KEY_KP0 82
+#define KEY_KPDOT 83
+
+#define KEY_ZENKAKUHANKAKU 85
+#define KEY_102ND 86
+#define KEY_F11 87
+#define KEY_F12 88
+#define KEY_RO 89
+#define KEY_KATAKANA 90
+#define KEY_HIRAGANA 91
+#define KEY_HENKAN 92
+#define KEY_KATAKANAHIRAGANA 93
+#define KEY_MUHENKAN 94
+#define KEY_KPJPCOMMA 95
+#define KEY_KPENTER 96
+#define KEY_RIGHTCTRL 97
+#define KEY_KPSLASH 98
+#define KEY_SYSRQ 99
+#define KEY_RIGHTALT 100
+#define KEY_LINEFEED 101
+#define KEY_HOME 102
+#define KEY_UP 103
+#define KEY_PAGEUP 104
+#define KEY_LEFT 105
+#define KEY_RIGHT 106
+#define KEY_END 107
+#define KEY_DOWN 108
+#define KEY_PAGEDOWN 109
+#define KEY_INSERT 110
+#define KEY_DELETE 111
+#define KEY_MACRO 112
+#define KEY_MUTE 113
+#define KEY_VOLUMEDOWN 114
+#define KEY_VOLUMEUP 115
+#define KEY_POWER 116 /* SC System Power Down */
+#define KEY_KPEQUAL 117
+#define KEY_KPPLUSMINUS 118
+#define KEY_PAUSE 119
+#define KEY_SCALE 120 /* AL Compiz Scale (Expose) */
+
+#define KEY_KPCOMMA 121
+#define KEY_HANGEUL 122
+#define KEY_HANGUEL KEY_HANGEUL
+#define KEY_HANJA 123
+#define KEY_YEN 124
+#define KEY_LEFTMETA 125
+#define KEY_RIGHTMETA 126
+#define KEY_COMPOSE 127
+
+#define KEY_STOP 128 /* AC Stop */
+#define KEY_AGAIN 129
+#define KEY_PROPS 130 /* AC Properties */
+#define KEY_UNDO 131 /* AC Undo */
+#define KEY_FRONT 132
+#define KEY_COPY 133 /* AC Copy */
+#define KEY_OPEN 134 /* AC Open */
+#define KEY_PASTE 135 /* AC Paste */
+#define KEY_FIND 136 /* AC Search */
+#define KEY_CUT 137 /* AC Cut */
+#define KEY_HELP 138 /* AL Integrated Help Center */
+#define KEY_MENU 139 /* Menu (show menu) */
+#define KEY_CALC 140 /* AL Calculator */
+#define KEY_SETUP 141
+#define KEY_SLEEP 142 /* SC System Sleep */
+#define KEY_WAKEUP 143 /* System Wake Up */
+#define KEY_FILE 144 /* AL Local Machine Browser */
+#define KEY_SENDFILE 145
+#define KEY_DELETEFILE 146
+#define KEY_XFER 147
+#define KEY_PROG1 148
+#define KEY_PROG2 149
+#define KEY_WWW 150 /* AL Internet Browser */
+#define KEY_MSDOS 151
+#define KEY_COFFEE 152 /* AL Terminal Lock/Screensaver */
+#define KEY_SCREENLOCK KEY_COFFEE
+#define KEY_ROTATE_DISPLAY 153 /* Display orientation for e.g. tablets */
+#define KEY_DIRECTION KEY_ROTATE_DISPLAY
+#define KEY_CYCLEWINDOWS 154
+#define KEY_MAIL 155
+#define KEY_BOOKMARKS 156 /* AC Bookmarks */
+#define KEY_COMPUTER 157
+#define KEY_BACK 158 /* AC Back */
+#define KEY_FORWARD 159 /* AC Forward */
+#define KEY_CLOSECD 160
+#define KEY_EJECTCD 161
+#define KEY_EJECTCLOSECD 162
+#define KEY_NEXTSONG 163
+#define KEY_PLAYPAUSE 164
+#define KEY_PREVIOUSSONG 165
+#define KEY_STOPCD 166
+#define KEY_RECORD 167
+#define KEY_REWIND 168
+#define KEY_PHONE 169 /* Media Select Telephone */
+#define KEY_ISO 170
+#define KEY_CONFIG 171 /* AL Consumer Control Configuration */
+#define KEY_HOMEPAGE 172 /* AC Home */
+#define KEY_REFRESH 173 /* AC Refresh */
+#define KEY_EXIT 174 /* AC Exit */
+#define KEY_MOVE 175
+#define KEY_EDIT 176
+#define KEY_SCROLLUP 177
+#define KEY_SCROLLDOWN 178
+#define KEY_KPLEFTPAREN 179
+#define KEY_KPRIGHTPAREN 180
+#define KEY_NEW 181 /* AC New */
+#define KEY_REDO 182 /* AC Redo/Repeat */
+
+#define KEY_F13 183
+#define KEY_F14 184
+#define KEY_F15 185
+#define KEY_F16 186
+#define KEY_F17 187
+#define KEY_F18 188
+#define KEY_F19 189
+#define KEY_F20 190
+#define KEY_F21 191
+#define KEY_F22 192
+#define KEY_F23 193
+#define KEY_F24 194
+
+#define KEY_PLAYCD 200
+#define KEY_PAUSECD 201
+#define KEY_PROG3 202
+#define KEY_PROG4 203
+#define KEY_DASHBOARD 204 /* AL Dashboard */
+#define KEY_SUSPEND 205
+#define KEY_CLOSE 206 /* AC Close */
+#define KEY_PLAY 207
+#define KEY_FASTFORWARD 208
+#define KEY_BASSBOOST 209
+#define KEY_PRINT 210 /* AC Print */
+#define KEY_HP 211
+#define KEY_CAMERA 212
+#define KEY_SOUND 213
+#define KEY_QUESTION 214
+#define KEY_EMAIL 215
+#define KEY_CHAT 216
+#define KEY_SEARCH 217
+#define KEY_CONNECT 218
+#define KEY_FINANCE 219 /* AL Checkbook/Finance */
+#define KEY_SPORT 220
+#define KEY_SHOP 221
+#define KEY_ALTERASE 222
+#define KEY_CANCEL 223 /* AC Cancel */
+#define KEY_BRIGHTNESSDOWN 224
+#define KEY_BRIGHTNESSUP 225
+#define KEY_MEDIA 226
+
+#define KEY_SWITCHVIDEOMODE 227 /* Cycle between available video
+ outputs (Monitor/LCD/TV-out/etc) */
+#define KEY_KBDILLUMTOGGLE 228
+#define KEY_KBDILLUMDOWN 229
+#define KEY_KBDILLUMUP 230
+
+#define KEY_SEND 231 /* AC Send */
+#define KEY_REPLY 232 /* AC Reply */
+#define KEY_FORWARDMAIL 233 /* AC Forward Msg */
+#define KEY_SAVE 234 /* AC Save */
+#define KEY_DOCUMENTS 235
+
+#define KEY_BATTERY 236
+
+#define KEY_BLUETOOTH 237
+#define KEY_WLAN 238
+#define KEY_UWB 239
+
+#define KEY_UNKNOWN 240
+
+#define KEY_VIDEO_NEXT 241 /* drive next video source */
+#define KEY_VIDEO_PREV 242 /* drive previous video source */
+#define KEY_BRIGHTNESS_CYCLE 243 /* brightness up, after max is min */
+#define KEY_BRIGHTNESS_AUTO 244 /* Set Auto Brightness: manual
+ brightness control is off,
+ rely on ambient */
+#define KEY_BRIGHTNESS_ZERO KEY_BRIGHTNESS_AUTO
+#define KEY_DISPLAY_OFF 245 /* display device to off state */
+
+#define KEY_WWAN 246 /* Wireless WAN (LTE, UMTS, GSM, etc.) */
+#define KEY_WIMAX KEY_WWAN
+#define KEY_RFKILL 247 /* Key that controls all radios */
+
+#define KEY_MICMUTE 248 /* Mute / unmute the microphone */
+
+/* Code 255 is reserved for special needs of AT keyboard driver */
+
+#define BTN_MISC 0x100
+#define BTN_0 0x100
+#define BTN_1 0x101
+#define BTN_2 0x102
+#define BTN_3 0x103
+#define BTN_4 0x104
+#define BTN_5 0x105
+#define BTN_6 0x106
+#define BTN_7 0x107
+#define BTN_8 0x108
+#define BTN_9 0x109
+
+#define BTN_MOUSE 0x110
+#define BTN_LEFT 0x110
+#define BTN_RIGHT 0x111
+#define BTN_MIDDLE 0x112
+#define BTN_SIDE 0x113
+#define BTN_EXTRA 0x114
+#define BTN_FORWARD 0x115
+#define BTN_BACK 0x116
+#define BTN_TASK 0x117
+
+#define BTN_JOYSTICK 0x120
+#define BTN_TRIGGER 0x120
+#define BTN_THUMB 0x121
+#define BTN_THUMB2 0x122
+#define BTN_TOP 0x123
+#define BTN_TOP2 0x124
+#define BTN_PINKIE 0x125
+#define BTN_BASE 0x126
+#define BTN_BASE2 0x127
+#define BTN_BASE3 0x128
+#define BTN_BASE4 0x129
+#define BTN_BASE5 0x12a
+#define BTN_BASE6 0x12b
+#define BTN_DEAD 0x12f
+
+#define BTN_GAMEPAD 0x130
+#define BTN_SOUTH 0x130
+#define BTN_A BTN_SOUTH
+#define BTN_EAST 0x131
+#define BTN_B BTN_EAST
+#define BTN_C 0x132
+#define BTN_NORTH 0x133
+#define BTN_X BTN_NORTH
+#define BTN_WEST 0x134
+#define BTN_Y BTN_WEST
+#define BTN_Z 0x135
+#define BTN_TL 0x136
+#define BTN_TR 0x137
+#define BTN_TL2 0x138
+#define BTN_TR2 0x139
+#define BTN_SELECT 0x13a
+#define BTN_START 0x13b
+#define BTN_MODE 0x13c
+#define BTN_THUMBL 0x13d
+#define BTN_THUMBR 0x13e
+
+#define BTN_DIGI 0x140
+#define BTN_TOOL_PEN 0x140
+#define BTN_TOOL_RUBBER 0x141
+#define BTN_TOOL_BRUSH 0x142
+#define BTN_TOOL_PENCIL 0x143
+#define BTN_TOOL_AIRBRUSH 0x144
+#define BTN_TOOL_FINGER 0x145
+#define BTN_TOOL_MOUSE 0x146
+#define BTN_TOOL_LENS 0x147
+#define BTN_TOOL_QUINTTAP 0x148 /* Five fingers on trackpad */
+#define BTN_TOUCH 0x14a
+#define BTN_STYLUS 0x14b
+#define BTN_STYLUS2 0x14c
+#define BTN_TOOL_DOUBLETAP 0x14d
+#define BTN_TOOL_TRIPLETAP 0x14e
+#define BTN_TOOL_QUADTAP 0x14f /* Four fingers on trackpad */
+
+#define BTN_WHEEL 0x150
+#define BTN_GEAR_DOWN 0x150
+#define BTN_GEAR_UP 0x151
+
+#define KEY_OK 0x160
+#define KEY_SELECT 0x161
+#define KEY_GOTO 0x162
+#define KEY_CLEAR 0x163
+#define KEY_POWER2 0x164
+#define KEY_OPTION 0x165
+#define KEY_INFO 0x166 /* AL OEM Features/Tips/Tutorial */
+#define KEY_TIME 0x167
+#define KEY_VENDOR 0x168
+#define KEY_ARCHIVE 0x169
+#define KEY_PROGRAM 0x16a /* Media Select Program Guide */
+#define KEY_CHANNEL 0x16b
+#define KEY_FAVORITES 0x16c
+#define KEY_EPG 0x16d
+#define KEY_PVR 0x16e /* Media Select Home */
+#define KEY_MHP 0x16f
+#define KEY_LANGUAGE 0x170
+#define KEY_TITLE 0x171
+#define KEY_SUBTITLE 0x172
+#define KEY_ANGLE 0x173
+#define KEY_ZOOM 0x174
+#define KEY_MODE 0x175
+#define KEY_KEYBOARD 0x176
+#define KEY_SCREEN 0x177
+#define KEY_PC 0x178 /* Media Select Computer */
+#define KEY_TV 0x179 /* Media Select TV */
+#define KEY_TV2 0x17a /* Media Select Cable */
+#define KEY_VCR 0x17b /* Media Select VCR */
+#define KEY_VCR2 0x17c /* VCR Plus */
+#define KEY_SAT 0x17d /* Media Select Satellite */
+#define KEY_SAT2 0x17e
+#define KEY_CD 0x17f /* Media Select CD */
+#define KEY_TAPE 0x180 /* Media Select Tape */
+#define KEY_RADIO 0x181
+#define KEY_TUNER 0x182 /* Media Select Tuner */
+#define KEY_PLAYER 0x183
+#define KEY_TEXT 0x184
+#define KEY_DVD 0x185 /* Media Select DVD */
+#define KEY_AUX 0x186
+#define KEY_MP3 0x187
+#define KEY_AUDIO 0x188 /* AL Audio Browser */
+#define KEY_VIDEO 0x189 /* AL Movie Browser */
+#define KEY_DIRECTORY 0x18a
+#define KEY_LIST 0x18b
+#define KEY_MEMO 0x18c /* Media Select Messages */
+#define KEY_CALENDAR 0x18d
+#define KEY_RED 0x18e
+#define KEY_GREEN 0x18f
+#define KEY_YELLOW 0x190
+#define KEY_BLUE 0x191
+#define KEY_CHANNELUP 0x192 /* Channel Increment */
+#define KEY_CHANNELDOWN 0x193 /* Channel Decrement */
+#define KEY_FIRST 0x194
+#define KEY_LAST 0x195 /* Recall Last */
+#define KEY_AB 0x196
+#define KEY_NEXT 0x197
+#define KEY_RESTART 0x198
+#define KEY_SLOW 0x199
+#define KEY_SHUFFLE 0x19a
+#define KEY_BREAK 0x19b
+#define KEY_PREVIOUS 0x19c
+#define KEY_DIGITS 0x19d
+#define KEY_TEEN 0x19e
+#define KEY_TWEN 0x19f
+#define KEY_VIDEOPHONE 0x1a0 /* Media Select Video Phone */
+#define KEY_GAMES 0x1a1 /* Media Select Games */
+#define KEY_ZOOMIN 0x1a2 /* AC Zoom In */
+#define KEY_ZOOMOUT 0x1a3 /* AC Zoom Out */
+#define KEY_ZOOMRESET 0x1a4 /* AC Zoom */
+#define KEY_WORDPROCESSOR 0x1a5 /* AL Word Processor */
+#define KEY_EDITOR 0x1a6 /* AL Text Editor */
+#define KEY_SPREADSHEET 0x1a7 /* AL Spreadsheet */
+#define KEY_GRAPHICSEDITOR 0x1a8 /* AL Graphics Editor */
+#define KEY_PRESENTATION 0x1a9 /* AL Presentation App */
+#define KEY_DATABASE 0x1aa /* AL Database App */
+#define KEY_NEWS 0x1ab /* AL Newsreader */
+#define KEY_VOICEMAIL 0x1ac /* AL Voicemail */
+#define KEY_ADDRESSBOOK 0x1ad /* AL Contacts/Address Book */
+#define KEY_MESSENGER 0x1ae /* AL Instant Messaging */
+#define KEY_DISPLAYTOGGLE 0x1af /* Turn display (LCD) on and off */
+#define KEY_BRIGHTNESS_TOGGLE KEY_DISPLAYTOGGLE
+#define KEY_SPELLCHECK 0x1b0 /* AL Spell Check */
+#define KEY_LOGOFF 0x1b1 /* AL Logoff */
+
+#define KEY_DOLLAR 0x1b2
+#define KEY_EURO 0x1b3
+
+#define KEY_FRAMEBACK 0x1b4 /* Consumer - transport controls */
+#define KEY_FRAMEFORWARD 0x1b5
+#define KEY_CONTEXT_MENU 0x1b6 /* GenDesc - system context menu */
+#define KEY_MEDIA_REPEAT 0x1b7 /* Consumer - transport control */
+#define KEY_10CHANNELSUP 0x1b8 /* 10 channels up (10+) */
+#define KEY_10CHANNELSDOWN 0x1b9 /* 10 channels down (10-) */
+#define KEY_IMAGES 0x1ba /* AL Image Browser */
+
+#define KEY_DEL_EOL 0x1c0
+#define KEY_DEL_EOS 0x1c1
+#define KEY_INS_LINE 0x1c2
+#define KEY_DEL_LINE 0x1c3
+
+#define KEY_FN 0x1d0
+#define KEY_FN_ESC 0x1d1
+#define KEY_FN_F1 0x1d2
+#define KEY_FN_F2 0x1d3
+#define KEY_FN_F3 0x1d4
+#define KEY_FN_F4 0x1d5
+#define KEY_FN_F5 0x1d6
+#define KEY_FN_F6 0x1d7
+#define KEY_FN_F7 0x1d8
+#define KEY_FN_F8 0x1d9
+#define KEY_FN_F9 0x1da
+#define KEY_FN_F10 0x1db
+#define KEY_FN_F11 0x1dc
+#define KEY_FN_F12 0x1dd
+#define KEY_FN_1 0x1de
+#define KEY_FN_2 0x1df
+#define KEY_FN_D 0x1e0
+#define KEY_FN_E 0x1e1
+#define KEY_FN_F 0x1e2
+#define KEY_FN_S 0x1e3
+#define KEY_FN_B 0x1e4
+
+#define KEY_BRL_DOT1 0x1f1
+#define KEY_BRL_DOT2 0x1f2
+#define KEY_BRL_DOT3 0x1f3
+#define KEY_BRL_DOT4 0x1f4
+#define KEY_BRL_DOT5 0x1f5
+#define KEY_BRL_DOT6 0x1f6
+#define KEY_BRL_DOT7 0x1f7
+#define KEY_BRL_DOT8 0x1f8
+#define KEY_BRL_DOT9 0x1f9
+#define KEY_BRL_DOT10 0x1fa
+
+#define KEY_NUMERIC_0 0x200 /* used by phones, remote controls, */
+#define KEY_NUMERIC_1 0x201 /* and other keypads */
+#define KEY_NUMERIC_2 0x202
+#define KEY_NUMERIC_3 0x203
+#define KEY_NUMERIC_4 0x204
+#define KEY_NUMERIC_5 0x205
+#define KEY_NUMERIC_6 0x206
+#define KEY_NUMERIC_7 0x207
+#define KEY_NUMERIC_8 0x208
+#define KEY_NUMERIC_9 0x209
+#define KEY_NUMERIC_STAR 0x20a
+#define KEY_NUMERIC_POUND 0x20b
+#define KEY_NUMERIC_A 0x20c /* Phone key A - HUT Telephony 0xb9 */
+#define KEY_NUMERIC_B 0x20d
+#define KEY_NUMERIC_C 0x20e
+#define KEY_NUMERIC_D 0x20f
+
+#define KEY_CAMERA_FOCUS 0x210
+#define KEY_WPS_BUTTON 0x211 /* WiFi Protected Setup key */
+
+#define KEY_TOUCHPAD_TOGGLE 0x212 /* Request switch touchpad on or off */
+#define KEY_TOUCHPAD_ON 0x213
+#define KEY_TOUCHPAD_OFF 0x214
+
+#define KEY_CAMERA_ZOOMIN 0x215
+#define KEY_CAMERA_ZOOMOUT 0x216
+#define KEY_CAMERA_UP 0x217
+#define KEY_CAMERA_DOWN 0x218
+#define KEY_CAMERA_LEFT 0x219
+#define KEY_CAMERA_RIGHT 0x21a
+
+#define KEY_ATTENDANT_ON 0x21b
+#define KEY_ATTENDANT_OFF 0x21c
+#define KEY_ATTENDANT_TOGGLE 0x21d /* Attendant call on or off */
+#define KEY_LIGHTS_TOGGLE 0x21e /* Reading light on or off */
+
+#define BTN_DPAD_UP 0x220
+#define BTN_DPAD_DOWN 0x221
+#define BTN_DPAD_LEFT 0x222
+#define BTN_DPAD_RIGHT 0x223
+
+#define KEY_ALS_TOGGLE 0x230 /* Ambient light sensor */
+
+#define KEY_BUTTONCONFIG 0x240 /* AL Button Configuration */
+#define KEY_TASKMANAGER 0x241 /* AL Task/Project Manager */
+#define KEY_JOURNAL 0x242 /* AL Log/Journal/Timecard */
+#define KEY_CONTROLPANEL 0x243 /* AL Control Panel */
+#define KEY_APPSELECT 0x244 /* AL Select Task/Application */
+#define KEY_SCREENSAVER 0x245 /* AL Screen Saver */
+#define KEY_VOICECOMMAND 0x246 /* Listening Voice Command */
+
+#define KEY_BRIGHTNESS_MIN 0x250 /* Set Brightness to Minimum */
+#define KEY_BRIGHTNESS_MAX 0x251 /* Set Brightness to Maximum */
+
+#define KEY_KBDINPUTASSIST_PREV 0x260
+#define KEY_KBDINPUTASSIST_NEXT 0x261
+#define KEY_KBDINPUTASSIST_PREVGROUP 0x262
+#define KEY_KBDINPUTASSIST_NEXTGROUP 0x263
+#define KEY_KBDINPUTASSIST_ACCEPT 0x264
+#define KEY_KBDINPUTASSIST_CANCEL 0x265
+
+#define BTN_TRIGGER_HAPPY 0x2c0
+#define BTN_TRIGGER_HAPPY1 0x2c0
+#define BTN_TRIGGER_HAPPY2 0x2c1
+#define BTN_TRIGGER_HAPPY3 0x2c2
+#define BTN_TRIGGER_HAPPY4 0x2c3
+#define BTN_TRIGGER_HAPPY5 0x2c4
+#define BTN_TRIGGER_HAPPY6 0x2c5
+#define BTN_TRIGGER_HAPPY7 0x2c6
+#define BTN_TRIGGER_HAPPY8 0x2c7
+#define BTN_TRIGGER_HAPPY9 0x2c8
+#define BTN_TRIGGER_HAPPY10 0x2c9
+#define BTN_TRIGGER_HAPPY11 0x2ca
+#define BTN_TRIGGER_HAPPY12 0x2cb
+#define BTN_TRIGGER_HAPPY13 0x2cc
+#define BTN_TRIGGER_HAPPY14 0x2cd
+#define BTN_TRIGGER_HAPPY15 0x2ce
+#define BTN_TRIGGER_HAPPY16 0x2cf
+#define BTN_TRIGGER_HAPPY17 0x2d0
+#define BTN_TRIGGER_HAPPY18 0x2d1
+#define BTN_TRIGGER_HAPPY19 0x2d2
+#define BTN_TRIGGER_HAPPY20 0x2d3
+#define BTN_TRIGGER_HAPPY21 0x2d4
+#define BTN_TRIGGER_HAPPY22 0x2d5
+#define BTN_TRIGGER_HAPPY23 0x2d6
+#define BTN_TRIGGER_HAPPY24 0x2d7
+#define BTN_TRIGGER_HAPPY25 0x2d8
+#define BTN_TRIGGER_HAPPY26 0x2d9
+#define BTN_TRIGGER_HAPPY27 0x2da
+#define BTN_TRIGGER_HAPPY28 0x2db
+#define BTN_TRIGGER_HAPPY29 0x2dc
+#define BTN_TRIGGER_HAPPY30 0x2dd
+#define BTN_TRIGGER_HAPPY31 0x2de
+#define BTN_TRIGGER_HAPPY32 0x2df
+#define BTN_TRIGGER_HAPPY33 0x2e0
+#define BTN_TRIGGER_HAPPY34 0x2e1
+#define BTN_TRIGGER_HAPPY35 0x2e2
+#define BTN_TRIGGER_HAPPY36 0x2e3
+#define BTN_TRIGGER_HAPPY37 0x2e4
+#define BTN_TRIGGER_HAPPY38 0x2e5
+#define BTN_TRIGGER_HAPPY39 0x2e6
+#define BTN_TRIGGER_HAPPY40 0x2e7
+
+/* We avoid low common keys in module aliases so they don't get huge. */
+#define KEY_MIN_INTERESTING KEY_MUTE
+#define KEY_MAX 0x2ff
+#define KEY_CNT (KEY_MAX+1)
+
+/*
+ * Relative axes
+ */
+
+#define REL_X 0x00
+#define REL_Y 0x01
+#define REL_Z 0x02
+#define REL_RX 0x03
+#define REL_RY 0x04
+#define REL_RZ 0x05
+#define REL_HWHEEL 0x06
+#define REL_DIAL 0x07
+#define REL_WHEEL 0x08
+#define REL_MISC 0x09
+#define REL_MAX 0x0f
+#define REL_CNT (REL_MAX+1)
+
+/*
+ * Absolute axes
+ */
+
+#define ABS_X 0x00
+#define ABS_Y 0x01
+#define ABS_Z 0x02
+#define ABS_RX 0x03
+#define ABS_RY 0x04
+#define ABS_RZ 0x05
+#define ABS_THROTTLE 0x06
+#define ABS_RUDDER 0x07
+#define ABS_WHEEL 0x08
+#define ABS_GAS 0x09
+#define ABS_BRAKE 0x0a
+#define ABS_HAT0X 0x10
+#define ABS_HAT0Y 0x11
+#define ABS_HAT1X 0x12
+#define ABS_HAT1Y 0x13
+#define ABS_HAT2X 0x14
+#define ABS_HAT2Y 0x15
+#define ABS_HAT3X 0x16
+#define ABS_HAT3Y 0x17
+#define ABS_PRESSURE 0x18
+#define ABS_DISTANCE 0x19
+#define ABS_TILT_X 0x1a
+#define ABS_TILT_Y 0x1b
+#define ABS_TOOL_WIDTH 0x1c
+
+#define ABS_VOLUME 0x20
+
+#define ABS_MISC 0x28
+
+#define ABS_MT_SLOT 0x2f /* MT slot being modified */
+#define ABS_MT_TOUCH_MAJOR 0x30 /* Major axis of touching ellipse */
+#define ABS_MT_TOUCH_MINOR 0x31 /* Minor axis (omit if circular) */
+#define ABS_MT_WIDTH_MAJOR 0x32 /* Major axis of approaching ellipse */
+#define ABS_MT_WIDTH_MINOR 0x33 /* Minor axis (omit if circular) */
+#define ABS_MT_ORIENTATION 0x34 /* Ellipse orientation */
+#define ABS_MT_POSITION_X 0x35 /* Center X touch position */
+#define ABS_MT_POSITION_Y 0x36 /* Center Y touch position */
+#define ABS_MT_TOOL_TYPE 0x37 /* Type of touching device */
+#define ABS_MT_BLOB_ID 0x38 /* Group a set of packets as a blob */
+#define ABS_MT_TRACKING_ID 0x39 /* Unique ID of initiated contact */
+#define ABS_MT_PRESSURE 0x3a /* Pressure on contact area */
+#define ABS_MT_DISTANCE 0x3b /* Contact hover distance */
+#define ABS_MT_TOOL_X 0x3c /* Center X tool position */
+#define ABS_MT_TOOL_Y 0x3d /* Center Y tool position */
+
+
+#define ABS_MAX 0x3f
+#define ABS_CNT (ABS_MAX+1)
+
+/*
+ * Switch events
+ */
+
+#define SW_LID 0x00 /* set = lid shut */
+#define SW_TABLET_MODE 0x01 /* set = tablet mode */
+#define SW_HEADPHONE_INSERT 0x02 /* set = inserted */
+#define SW_RFKILL_ALL 0x03 /* rfkill master switch, type "any"
+ set = radio enabled */
+#define SW_RADIO SW_RFKILL_ALL /* deprecated */
+#define SW_MICROPHONE_INSERT 0x04 /* set = inserted */
+#define SW_DOCK 0x05 /* set = plugged into dock */
+#define SW_LINEOUT_INSERT 0x06 /* set = inserted */
+#define SW_JACK_PHYSICAL_INSERT 0x07 /* set = mechanical switch set */
+#define SW_VIDEOOUT_INSERT 0x08 /* set = inserted */
+#define SW_CAMERA_LENS_COVER 0x09 /* set = lens covered */
+#define SW_KEYPAD_SLIDE 0x0a /* set = keypad slide out */
+#define SW_FRONT_PROXIMITY 0x0b /* set = front proximity sensor active */
+#define SW_ROTATE_LOCK 0x0c /* set = rotate locked/disabled */
+#define SW_LINEIN_INSERT 0x0d /* set = inserted */
+#define SW_MUTE_DEVICE 0x0e /* set = device disabled */
+#define SW_MAX 0x0f
+#define SW_CNT (SW_MAX+1)
+
+/*
+ * Misc events
+ */
+
+#define MSC_SERIAL 0x00
+#define MSC_PULSELED 0x01
+#define MSC_GESTURE 0x02
+#define MSC_RAW 0x03
+#define MSC_SCAN 0x04
+#define MSC_TIMESTAMP 0x05
+#define MSC_MAX 0x07
+#define MSC_CNT (MSC_MAX+1)
+
+/*
+ * LEDs
+ */
+
+#define LED_NUML 0x00
+#define LED_CAPSL 0x01
+#define LED_SCROLLL 0x02
+#define LED_COMPOSE 0x03
+#define LED_KANA 0x04
+#define LED_SLEEP 0x05
+#define LED_SUSPEND 0x06
+#define LED_MUTE 0x07
+#define LED_MISC 0x08
+#define LED_MAIL 0x09
+#define LED_CHARGING 0x0a
+#define LED_MAX 0x0f
+#define LED_CNT (LED_MAX+1)
+
+/*
+ * Autorepeat values
+ */
+
+#define REP_DELAY 0x00
+#define REP_PERIOD 0x01
+#define REP_MAX 0x01
+#define REP_CNT (REP_MAX+1)
+
+/*
+ * Sounds
+ */
+
+#define SND_CLICK 0x00
+#define SND_BELL 0x01
+#define SND_TONE 0x02
+#define SND_MAX 0x07
+#define SND_CNT (SND_MAX+1)
+
+#endif
projects / people / ms / u-boot.git / commitdiff
