--- /dev/null
+/*
+ * Copyright (C) 2015 Marek Vasut <marex@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/atmel_mpddrc.h>
+#include <asm/arch/atmel_usba_udc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/sama5d3_smc.h>
+#include <asm/arch/sama5d4.h>
+#include <atmel_hlcdc.h>
+#include <atmel_mci.h>
+#include <lcd.h>
+#include <mmc.h>
+#include <net.h>
+#include <netdev.h>
+#include <spi.h>
+#include <version.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_ATMEL_SPI
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+ return bus == 0 && cs == 0;
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+ at91_set_pio_output(AT91_PIO_PORTC, 3, 0);
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+ at91_set_pio_output(AT91_PIO_PORTC, 3, 1);
+}
+
+static void ma5d4evk_spi0_hw_init(void)
+{
+ at91_set_a_periph(AT91_PIO_PORTC, 0, 0); /* SPI0_MISO */
+ at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* SPI0_MOSI */
+ at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* SPI0_SPCK */
+
+ at91_set_pio_output(AT91_PIO_PORTC, 3, 1); /* SPI0_CS0 */
+
+ /* Enable clock */
+ at91_periph_clk_enable(ATMEL_ID_SPI0);
+}
+#endif /* CONFIG_ATMEL_SPI */
+
+#ifdef CONFIG_CMD_USB
+static void ma5d4evk_usb_hw_init(void)
+{
+ at91_set_pio_output(AT91_PIO_PORTE, 11, 0);
+ at91_set_pio_output(AT91_PIO_PORTE, 14, 0);
+}
+#endif
+
+#ifdef CONFIG_LCD
+vidinfo_t panel_info = {
+ .vl_col = 800,
+ .vl_row = 480,
+ .vl_clk = 33500000,
+ .vl_bpix = LCD_BPP,
+ .vl_tft = 1,
+ .vl_hsync_len = 10,
+ .vl_left_margin = 89,
+ .vl_right_margin = 164,
+ .vl_vsync_len = 10,
+ .vl_upper_margin = 23,
+ .vl_lower_margin = 10,
+ .mmio = ATMEL_BASE_LCDC,
+};
+
+/* No power up/down pin for the LCD pannel */
+void lcd_enable(void) { /* Empty! */ }
+void lcd_disable(void) { /* Empty! */ }
+
+unsigned int has_lcdc(void)
+{
+ return 1;
+}
+
+static void ma5d4evk_lcd_hw_init(void)
+{
+ at91_set_a_periph(AT91_PIO_PORTA, 24, 1); /* LCDPWM */
+ at91_set_a_periph(AT91_PIO_PORTA, 25, 0); /* LCDDISP */
+ at91_set_a_periph(AT91_PIO_PORTA, 26, 0); /* LCDVSYNC */
+ at91_set_a_periph(AT91_PIO_PORTA, 27, 0); /* LCDHSYNC */
+ at91_set_a_periph(AT91_PIO_PORTA, 28, 0); /* LCDDOTCK */
+ at91_set_a_periph(AT91_PIO_PORTA, 29, 1); /* LCDDEN */
+
+ at91_set_a_periph(AT91_PIO_PORTA, 0, 0); /* LCDD0 */
+ at91_set_a_periph(AT91_PIO_PORTA, 1, 0); /* LCDD1 */
+ at91_set_a_periph(AT91_PIO_PORTA, 2, 0); /* LCDD2 */
+ at91_set_a_periph(AT91_PIO_PORTA, 3, 0); /* LCDD3 */
+ at91_set_a_periph(AT91_PIO_PORTA, 4, 0); /* LCDD4 */
+ at91_set_a_periph(AT91_PIO_PORTA, 5, 0); /* LCDD5 */
+ at91_set_a_periph(AT91_PIO_PORTA, 6, 0); /* LCDD6 */
+ at91_set_a_periph(AT91_PIO_PORTA, 7, 0); /* LCDD7 */
+
+ at91_set_a_periph(AT91_PIO_PORTA, 8, 0); /* LCDD9 */
+ at91_set_a_periph(AT91_PIO_PORTA, 9, 0); /* LCDD8 */
+ at91_set_a_periph(AT91_PIO_PORTA, 10, 0); /* LCDD10 */
+ at91_set_a_periph(AT91_PIO_PORTA, 11, 0); /* LCDD11 */
+ at91_set_a_periph(AT91_PIO_PORTA, 12, 0); /* LCDD12 */
+ at91_set_a_periph(AT91_PIO_PORTA, 13, 0); /* LCDD13 */
+ at91_set_a_periph(AT91_PIO_PORTA, 14, 0); /* LCDD14 */
+ at91_set_a_periph(AT91_PIO_PORTA, 15, 0); /* LCDD15 */
+
+ at91_set_a_periph(AT91_PIO_PORTA, 16, 0); /* LCDD16 */
+ at91_set_a_periph(AT91_PIO_PORTA, 17, 0); /* LCDD17 */
+ at91_set_a_periph(AT91_PIO_PORTA, 18, 0); /* LCDD18 */
+ at91_set_a_periph(AT91_PIO_PORTA, 19, 0); /* LCDD19 */
+ at91_set_a_periph(AT91_PIO_PORTA, 20, 0); /* LCDD20 */
+ at91_set_a_periph(AT91_PIO_PORTA, 21, 0); /* LCDD21 */
+ at91_set_a_periph(AT91_PIO_PORTA, 22, 0); /* LCDD22 */
+ at91_set_a_periph(AT91_PIO_PORTA, 23, 0); /* LCDD23 */
+
+ /* Enable clock */
+ at91_periph_clk_enable(ATMEL_ID_LCDC);
+}
+
+#endif /* CONFIG_LCD */
+
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+/* On-SoM eMMC */
+void ma5d4evk_mci0_hw_init(void)
+{
+ at91_set_b_periph(AT91_PIO_PORTC, 5, 1); /* MCI1 CDA */
+ at91_set_b_periph(AT91_PIO_PORTC, 6, 1); /* MCI1 DA0 */
+ at91_set_b_periph(AT91_PIO_PORTC, 7, 1); /* MCI1 DA1 */
+ at91_set_b_periph(AT91_PIO_PORTC, 8, 1); /* MCI1 DA2 */
+ at91_set_b_periph(AT91_PIO_PORTC, 9, 1); /* MCI1 DA3 */
+ at91_set_b_periph(AT91_PIO_PORTC, 10, 1); /* MCI1 DA4 */
+ at91_set_b_periph(AT91_PIO_PORTC, 11, 1); /* MCI1 DA5 */
+ at91_set_b_periph(AT91_PIO_PORTC, 12, 1); /* MCI1 DA6 */
+ at91_set_b_periph(AT91_PIO_PORTC, 13, 1); /* MCI1 DA7 */
+ at91_set_b_periph(AT91_PIO_PORTC, 4, 0); /* MCI1 CLK */
+
+ /*
+ * As the mci io internal pull down is too strong, so if the io needs
+ * external pull up, the pull up resistor will be very small, if so
+ * the power consumption will increase, so disable the internal pull
+ * down to save the power.
+ */
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 5, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 6, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 7, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 8, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 9, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 10, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 11, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 12, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 13, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 4, 0);
+
+ /* Enable clock */
+ at91_periph_clk_enable(ATMEL_ID_MCI0);
+}
+
+/* On-board MicroSD slot */
+void ma5d4evk_mci1_hw_init(void)
+{
+ at91_set_c_periph(AT91_PIO_PORTE, 19, 1); /* MCI1 CDA */
+ at91_set_c_periph(AT91_PIO_PORTE, 20, 1); /* MCI1 DA0 */
+ at91_set_c_periph(AT91_PIO_PORTE, 21, 1); /* MCI1 DA1 */
+ at91_set_c_periph(AT91_PIO_PORTE, 22, 1); /* MCI1 DA2 */
+ at91_set_c_periph(AT91_PIO_PORTE, 23, 1); /* MCI1 DA3 */
+ at91_set_c_periph(AT91_PIO_PORTE, 18, 0); /* MCI1 CLK */
+
+ /*
+ * As the mci io internal pull down is too strong, so if the io needs
+ * external pull up, the pull up resistor will be very small, if so
+ * the power consumption will increase, so disable the internal pull
+ * down to save the power.
+ */
+ at91_set_pio_pulldown(AT91_PIO_PORTE, 18, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTE, 19, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTE, 20, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTE, 21, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTE, 22, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTE, 23, 0);
+
+ /* Deal with WP pin on the microSD slot. */
+ at91_set_pio_output(AT91_PIO_PORTE, 16, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTE, 16, 1);
+
+ /* Enable clock */
+ at91_periph_clk_enable(ATMEL_ID_MCI1);
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ int ret;
+
+ /* De-assert reset on On-SoM eMMC */
+ at91_set_pio_output(AT91_PIO_PORTE, 15, 1);
+ at91_set_pio_pulldown(AT91_PIO_PORTE, 15, 0);
+
+ ret = atmel_mci_init((void *)ATMEL_BASE_MCI0);
+ if (ret) /* eMMC init failed, skip it. */
+ at91_set_pio_output(AT91_PIO_PORTE, 15, 0);
+
+ /* Enable the power supply to On-board MicroSD */
+ at91_set_pio_output(AT91_PIO_PORTE, 17, 0);
+
+ ret = atmel_mci_init((void *)ATMEL_BASE_MCI1);
+ if (ret) /* uSD init failed, power it down. */
+ at91_set_pio_output(AT91_PIO_PORTE, 17, 1);
+
+ return 0;
+}
+#endif /* CONFIG_GENERIC_ATMEL_MCI */
+
+#ifdef CONFIG_MACB
+void ma5d4evk_macb0_hw_init(void)
+{
+ at91_set_a_periph(AT91_PIO_PORTB, 0, 0); /* ETXCK_EREFCK */
+ at91_set_a_periph(AT91_PIO_PORTB, 6, 0); /* ERXDV */
+ at91_set_a_periph(AT91_PIO_PORTB, 8, 0); /* ERX0 */
+ at91_set_a_periph(AT91_PIO_PORTB, 9, 0); /* ERX1 */
+ at91_set_a_periph(AT91_PIO_PORTB, 7, 0); /* ERXER */
+ at91_set_a_periph(AT91_PIO_PORTB, 2, 0); /* ETXEN */
+ at91_set_a_periph(AT91_PIO_PORTB, 12, 0); /* ETX0 */
+ at91_set_a_periph(AT91_PIO_PORTB, 13, 0); /* ETX1 */
+ at91_set_a_periph(AT91_PIO_PORTB, 17, 0); /* EMDIO */
+ at91_set_a_periph(AT91_PIO_PORTB, 16, 0); /* EMDC */
+
+ /* Enable clock */
+ at91_periph_clk_enable(ATMEL_ID_GMAC0);
+}
+#endif
+
+static void ma5d4evk_serial_hw_init(void)
+{
+ /* USART0 */
+ at91_set_a_periph(AT91_PIO_PORTD, 13, 1); /* TXD */
+ at91_set_a_periph(AT91_PIO_PORTD, 12, 0); /* RXD */
+ at91_set_a_periph(AT91_PIO_PORTD, 11, 0); /* RTS */
+ at91_set_a_periph(AT91_PIO_PORTD, 10, 0); /* CTS */
+ at91_periph_clk_enable(ATMEL_ID_USART0);
+
+ /* USART1 */
+ at91_set_a_periph(AT91_PIO_PORTD, 17, 1); /* TXD */
+ at91_set_a_periph(AT91_PIO_PORTD, 16, 0); /* RXD */
+ at91_set_a_periph(AT91_PIO_PORTD, 15, 0); /* RTS */
+ at91_set_a_periph(AT91_PIO_PORTD, 14, 0); /* CTS */
+ at91_periph_clk_enable(ATMEL_ID_USART1);
+}
+
+int board_early_init_f(void)
+{
+ at91_periph_clk_enable(ATMEL_ID_PIOA);
+ at91_periph_clk_enable(ATMEL_ID_PIOB);
+ at91_periph_clk_enable(ATMEL_ID_PIOC);
+ at91_periph_clk_enable(ATMEL_ID_PIOD);
+ at91_periph_clk_enable(ATMEL_ID_PIOE);
+
+ /* Configure LEDs as OFF */
+ at91_set_pio_output(AT91_PIO_PORTD, 28, 0);
+ at91_set_pio_output(AT91_PIO_PORTD, 29, 0);
+ at91_set_pio_output(AT91_PIO_PORTD, 30, 0);
+
+ /* Reset CAN controllers */
+ at91_set_pio_output(AT91_PIO_PORTB, 21, 0);
+ udelay(100);
+ at91_set_pio_output(AT91_PIO_PORTB, 21, 1);
+ at91_set_pio_pulldown(AT91_PIO_PORTB, 21, 0);
+
+ ma5d4evk_serial_hw_init();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+#ifdef CONFIG_ATMEL_SPI
+ ma5d4evk_spi0_hw_init();
+#endif
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+ ma5d4evk_mci0_hw_init();
+ ma5d4evk_mci1_hw_init();
+#endif
+#ifdef CONFIG_MACB
+ ma5d4evk_macb0_hw_init();
+#endif
+#ifdef CONFIG_LCD
+ ma5d4evk_lcd_hw_init();
+#endif
+#ifdef CONFIG_CMD_USB
+ ma5d4evk_usb_hw_init();
+#endif
+#ifdef CONFIG_USB_GADGET_ATMEL_USBA
+ at91_udp_hw_init();
+#endif
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+ CONFIG_SYS_SDRAM_SIZE);
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+
+#ifdef CONFIG_MACB
+ rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC0, 0x00);
+#endif
+
+#ifdef CONFIG_USB_GADGET_ATMEL_USBA
+ usba_udc_probe(&pdata);
+#ifdef CONFIG_USB_ETH_RNDIS
+ usb_eth_initialize(bis);
+#endif
+#endif
+
+ return rc;
+}
+
+/* SPL */
+#ifdef CONFIG_SPL_BUILD
+void spl_board_init(void)
+{
+ ma5d4evk_spi0_hw_init();
+}
+
+static void ddr2_conf(struct atmel_mpddrc_config *ddr2)
+{
+ ddr2->md = (ATMEL_MPDDRC_MD_DBW_32_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
+
+ ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
+ ATMEL_MPDDRC_CR_NR_ROW_13 |
+ ATMEL_MPDDRC_CR_CAS_DDR_CAS3 |
+ ATMEL_MPDDRC_CR_NB_8BANKS |
+ ATMEL_MPDDRC_CR_NDQS_DISABLED |
+ ATMEL_MPDDRC_CR_DECOD_INTERLEAVED |
+ ATMEL_MPDDRC_CR_UNAL_SUPPORTED);
+
+ ddr2->rtr = 0x2b0;
+
+ ddr2->tpr0 = (8 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |
+ 3 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |
+ 3 << ATMEL_MPDDRC_TPR0_TWR_OFFSET |
+ 10 << ATMEL_MPDDRC_TPR0_TRC_OFFSET |
+ 3 << ATMEL_MPDDRC_TPR0_TRP_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET);
+
+ ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET |
+ 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
+ 25 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
+ 23 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
+
+ ddr2->tpr2 = (7 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
+ 3 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
+ 8 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
+}
+
+void mem_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+ struct atmel_mpddrc_config ddr2;
+
+ ddr2_conf(&ddr2);
+
+ /* enable MPDDR clock */
+ at91_periph_clk_enable(ATMEL_ID_MPDDRC);
+ writel(AT91_PMC_DDR, &pmc->scer);
+
+ /* DDRAM2 Controller initialize */
+ ddr2_init(ATMEL_BASE_MPDDRC, ATMEL_BASE_DDRCS, &ddr2);
+}
+
+void at91_pmc_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+ u32 tmp;
+
+ tmp = AT91_PMC_PLLAR_29 |
+ AT91_PMC_PLLXR_PLLCOUNT(0x3f) |
+ AT91_PMC_PLLXR_MUL(87) |
+ AT91_PMC_PLLXR_DIV(1);
+ at91_plla_init(tmp);
+
+ writel(0x0 << 8, &pmc->pllicpr);
+
+ tmp = AT91_PMC_MCKR_H32MXDIV |
+ AT91_PMC_MCKR_PLLADIV_2 |
+ AT91_PMC_MCKR_MDIV_3 |
+ AT91_PMC_MCKR_CSS_PLLA;
+ at91_mck_init(tmp);
+}
+#endif
--- /dev/null
+/*
+ * DENX MA5D4 configuration
+ * Copyright (C) 2015 Marek Vasut <marex@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __MA5D4EVK_CONFIG_H__
+#define __MA5D4EVK_CONFIG_H__
+
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_FIT
+
+#define CONFIG_TIMESTAMP /* Print image info with timestamp */
+
+#include "at91-sama5_common.h"
+#undef CONFIG_BOOTARGS
+#define CONFIG_SYS_USE_SERIALFLASH 1
+
+/*
+ * U-Boot Commands
+ */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_FAT_WRITE
+/*#define CONFIG_LCD*/
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_EXT4_WRITE
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FS_GENERIC
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_USB
+
+/*
+ * Memory configurations
+ */
+#define CONFIG_NR_DRAM_BANKS 1
+#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
+#define CONFIG_SYS_SDRAM_SIZE 0x10000000
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_INIT_SP_ADDR 0x210000
+#else
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_OFFSET 0x8000
+#define CONFIG_ENV_SIZE 0x4000
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+#define CONFIG_ENV_SECT_SIZE 0x1000
+
+/*
+ * U-Boot general configurations
+ */
+#define CONFIG_VERSION_VARIABLE /* U-BOOT version */
+
+/*
+ * Serial Driver
+ */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE ATMEL_BASE_USART0
+#define CONFIG_USART_ID ATMEL_ID_USART0
+
+/*
+ * Ethernet
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_MACB
+#define CONFIG_RMII
+#define CONFIG_NET_RETRY_COUNT 20
+#define CONFIG_MACB_SEARCH_PHY
+#define CONFIG_ARP_TIMEOUT 200UL
+#define CONFIG_IP_DEFRAG
+#endif
+
+/*
+ * LCD
+ */
+#ifdef CONFIG_LCD
+#define CONFIG_CMD_BMP
+#define CONFIG_BMP_16BPP
+#define CONFIG_BMP_24BPP
+#define CONFIG_BMP_32BPP
+#define LCD_BPP LCD_COLOR16
+#define LCD_OUTPUT_BPP 24
+#define CONFIG_ATMEL_HLCD
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#endif
+
+/*
+ * SD/MMC
+ */
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_GENERIC_ATMEL_MCI
+#endif
+
+/*
+ * SPI NOR (boot memory)
+ */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_ATMEL_SPI
+#define CONFIG_ATMEL_SPI0
+#define CONFIG_SPI_FLASH_ATMEL
+#define CONFIG_SF_DEFAULT_BUS 0
+#define CONFIG_SF_DEFAULT_CS 0
+#define CONFIG_SF_DEFAULT_SPEED 30000000
+#endif
+
+/*
+ * USB
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_ATMEL
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
+#define CONFIG_USB_STORAGE
+
+/* USB device */
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET_ATMEL_USBA
+#define CONFIG_USB_ETHER
+#define CONFIG_USB_ETH_RNDIS
+#define CONFIG_USBNET_MANUFACTURER "DENX"
+#endif
+
+/*
+ * Boot Linux
+ */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_INITRD_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTFILE "fitImage"
+#define CONFIG_BOOTARGS "console=ttyS3,115200"
+#define CONFIG_LOADADDR 0x20800000
+#define CONFIG_BOOTCOMMAND "run mmc_mmc"
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_OF_LIBFDT
+
+/*
+ * Extra Environments
+ */
+#define CONFIG_PREBOOT "run try_bootscript"
+#define CONFIG_HOSTNAME ma5d4evk
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "consdev=ttyS3\0" \
+ "baudrate=115200\0" \
+ "bootscript=boot.scr\0" \
+ "bootdev=/dev/mmcblk1p1\0" \
+ "bootpart=1:1\0" \
+ "rootdev=/dev/mmcblk1p2\0" \
+ "netdev=eth0\0" \
+ "kernel_addr_r=0x22000000\0" \
+ "update_spi_firmware_spl_addr=0x21000000\0" \
+ "update_spi_firmware_spl_filename=boot.bin\0" \
+ "update_spi_firmware_addr=0x22000000\0" \
+ "update_spi_firmware_filename=u-boot.img\0" \
+ "update_spi_firmware=" /* Update the SPI flash firmware */ \
+ "if sf probe ; then " \
+ "if tftp ${update_spi_firmware_spl_addr} " \
+ "${update_spi_firmware_spl_filename} ; then " \
+ "setenv update_spi_firmware_spl_filesize ${filesize} ; "\
+ "if tftp ${update_spi_firmware_addr} " \
+ "${update_spi_firmware_filename} ; then " \
+ "setenv update_spi_firmware_filesize ${filesize} ; " \
+ "sf update ${update_spi_firmware_spl_addr} 0x0 " \
+ "${update_spi_firmware_spl_filesize} ; " \
+ "sf update ${update_spi_firmware_addr} 0x10000 " \
+ "${update_spi_firmware_filesize} ; " \
+ "fi ; " \
+ "fi ; " \
+ "fi\0" \
+ "addcons=" \
+ "setenv bootargs ${bootargs} " \
+ "console=${consdev},${baudrate}\0" \
+ "addip=" \
+ "setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:" \
+ "${netmask}:${hostname}:${netdev}:off\0" \
+ "addmisc=" \
+ "setenv bootargs ${bootargs} ${miscargs}\0" \
+ "addargs=run addcons addmisc\0" \
+ "mmcload=" \
+ "mmc rescan ; " \
+ "load mmc ${bootpart} ${kernel_addr_r} ${bootfile}\0" \
+ "netload=" \
+ "tftp ${kernel_addr_r} ${hostname}/${bootfile}\0" \
+ "miscargs=nohlt panic=1\0" \
+ "mmcargs=setenv bootargs root=${rootdev} rw rootwait\0" \
+ "nfsargs=" \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath},v3,tcp\0" \
+ "mmc_mmc=" \
+ "run mmcload mmcargs addargs ; " \
+ "bootm ${kernel_addr_r}\0" \
+ "mmc_nfs=" \
+ "run mmcload nfsargs addip addargs ; " \
+ "bootm ${kernel_addr_r}\0" \
+ "net_mmc=" \
+ "run netload mmcargs addargs ; " \
+ "bootm ${kernel_addr_r}\0" \
+ "net_nfs=" \
+ "run netload nfsargs addip addargs ; " \
+ "bootm ${kernel_addr_r}\0" \
+ "try_bootscript=" \
+ "mmc rescan;" \
+ "if test -e mmc ${bootpart} ${bootscript} ; then " \
+ "if load mmc ${bootpart} ${kernel_addr_r} ${bootscript};"\
+ "then ; " \
+ "echo Running bootscript... ; " \
+ "source ${kernel_addr_r} ; " \
+ "fi ; " \
+ "fi\0"
+/* SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE 0x200000
+#define CONFIG_SPL_MAX_SIZE 0x10000
+#define CONFIG_SPL_BSS_START_ADDR 0x20000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
+#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SYS_MONITOR_LEN (512 << 10)
+
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x10000
+
+#endif /* __MA5D4EVK_CONFIG_H__ */
projects / people / ms / u-boot.git / commitdiff
