SDIO is not supported in u-boot, there is no point in enabling mmc3.
For this purpose, add u-boot specific dtsi that this will be included
automatically while building the dtb.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 17 May 2017 18:06:08 +0000 (14:06 -0400)]
scripts/Makefile.lib: Always have ...-u-boot.dtsi be able to override
The intention of having a -u-boot.dtsi file is to be able to make
changes to the provided upstream dts files as well as to be able to add
nodes. Change the logic for adding the file from making it the last
included file at the top of the dts to being included at the end of the
file.
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Restructure clock manager driver in the preparation to support A10.
Move the Gen5 specific code to _gen5 files.
- Change all uint32_t to u32 and change to use macro BIT(n) for bit shift.
- Check return value from wait_for_bit(). So change return type to int for
cm_write_with_phase() and cm_basic_init().
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Peng Fan [Thu, 13 Apr 2017 06:09:57 +0000 (14:09 +0800)]
imx: mx7dsabresd: enable more DM drivers
Enable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO
enabled. The 74x164 drivers needs SOFT_SPI and DM_GPIO enabled.
So needs to enable them together.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
Early backports of the imx wdog external reset feature occured before the
property was accepted upstream and used 'ext-reset-output' instead of
'fsl,ext-reset-output'. In order to support older kernels remove both
properties.
Jagan Teki [Sat, 6 May 2017 21:13:03 +0000 (02:43 +0530)]
geam6ul: Add mmc_late_init
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 6 May 2017 21:13:02 +0000 (02:43 +0530)]
geam6ul: Add modeboot env via board_late_init
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 6 May 2017 21:13:01 +0000 (02:43 +0530)]
icorem6: Add mmc_late_init
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 6 May 2017 21:13:00 +0000 (02:43 +0530)]
icorem6: Add modeboot env via board_late_init
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Peng Fan [Tue, 18 Apr 2017 12:41:52 +0000 (20:41 +0800)]
imx: thermal: update imx6 thermal driver according new equation
>From IC guys:
"
After a thorough accuracy study of the Temp sense circuit,
we found that with our current equation, an average part can
read 7 degrees lower than a known forced temperature.
We also found out that the standard variance was around 2C;
which is the tightest distribution that we could create.
We need to change the temp sense equation to center the average
part around the target temperature.
"
Peng Fan [Mon, 10 Apr 2017 11:44:33 +0000 (19:44 +0800)]
net: fec: do not access reserved register for i.MX6ULL
The MIB RAM and FIFO receive start register does not exist on
i.MX6ULL. Accessing these register will cause enet not work well or
cause system report fault.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
Tom Rini [Wed, 17 May 2017 18:13:58 +0000 (14:13 -0400)]
Merge git://git.denx.de/u-boot-uniphier
- Add workaround code to make LD20 SoC boot from ARM Trusted Firmware
- Sync DT with Linux to fix DTC warnings
- Add new SoC support code
- Misc fix, updates
Masahiro Yamada [Tue, 16 May 2017 05:35:15 +0000 (14:35 +0900)]
ARM: uniphier: move kernel physical base to 0x82080000
Reserve enough space below the kernel base.
The assumed address map is: 80000000 - 80ffffff : for IPP 81000000 - 81ffffff : for ARM secure 82000000 - : for Linux
Masahiro Yamada [Mon, 15 May 2017 05:23:46 +0000 (14:23 +0900)]
ARM: dts: uniphier: sync DT with Linux
Fix the following DTC warnings:
Warning (simple_bus_reg): Node /soc/system-bus@58c00000/support_card@1,1f00000/ethernet@00000000 simple-bus unit address format error, expected "0"
Warning (simple_bus_reg): Node /soc/system-bus@58c00000/support_card@1,1f00000/uart@000b0000 simple-bus unit address format error, expected "b0000"
Warning (simple_bus_reg): Node /soc/smpctrl@59800000 simple-bus unit address format error, expected "59801000"
Masahiro Yamada [Fri, 12 May 2017 13:49:02 +0000 (22:49 +0900)]
ARM: uniphier: add weird workaround code for LD20
When booting from ARM Trusted Firmware, U-Boot runs in EL1-NS.
The boot flow is as follows:
BL1 -> BL2 -> BL31 -> BL33 (i.e. U-Boot)
This boot sequence works fine for LD11 SoC (Cortex-A53), but LD20
SoC (Cortex-A72) hangs in U-Boot. The solution I found is to
read sctlr_el1 and write back the value as-is. This should be
no effect, but surprisingly fixes the problem for LD20 to boot.
I do not know why.
Bin Meng [Mon, 8 May 2017 02:52:30 +0000 (19:52 -0700)]
x86: minnowmax: Remove incorrect pad-offset of several pins
Remove 'pad-offset' of soc_gpio_s5_0, soc_gpio_s5_1, soc_gpio_s5_2,
pin_usb_host_en0 and pin_usb_host_en1. These offsets are actually
wrong. Correct value should be added by 0x2000, but since they
are supposed to be 'mode-gpio', 'pad-offset' is not needed at all.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 8 May 2017 02:52:29 +0000 (19:52 -0700)]
x86: ich6_gpio: Add use-lvl-write-cache for I/O access mode
Add a device-tree property use-lvl-write-cache that will cause
writes to lvl to be cached instead of read from lvl before each
write. This is required on some platforms that have the register
implemented as dual read/write (such as Baytrail).
Prior to this fix the blue USB port on the Minnowboard Max was
unusable since USB_HOST_EN0 was set high then immediately set
low when USB_HOST_EN1 was written.
This also resolves the 'gpio clear | set' command warning like:
"Warning: value of pin is still 0"
Signed-off-by: George McCollister <george.mccollister@gmail.com>
<rebased on latest origin/master, fixed all baytrail boards> Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Stefan Roese [Mon, 24 Apr 2017 07:48:04 +0000 (09:48 +0200)]
spi: ich: Configure SPI BIOS parameters for Linux upon U-Boot exit
This patch adds a remove function to the Intel ICH SPI driver, that will
be called upon U-Boot exit, directly before the OS (Linux) is started.
This function takes care of configuring the BIOS registers in the SPI
controller (similar to what a "standard" BIOS or coreboot does), so that
the Linux MTD device driver is able to correctly read/write to the SPI
NOR chip. Without this, the chip is not detected at all.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Jagan Teki <jteki@openedev.com>
Stefan Roese [Mon, 24 Apr 2017 07:48:03 +0000 (09:48 +0200)]
x86: bootm: Add dm_remove_devices_flags() call to bootm_announce_and_cleanup()
This patch adds a call to dm_remove_devices_flags() to
bootm_announce_and_cleanup() so that drivers that have one of the removal
flags set (e.g. DM_FLAG_ACTIVE_DMA_REMOVE) in their driver struct, may
do some last-stage cleanup before the OS is started.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / people / ms / u-boot.git / log
