]> git.ipfire.org Git - thirdparty/dracut.git/blob - dracut.conf.5.asc
dracut: Implement ACPI table overriding
[thirdparty/dracut.git] / dracut.conf.5.asc
1 DRACUT.CONF(5)
2 ==============
3 :doctype: manpage
4 :man source: dracut
5 :man manual: dracut
6
7 NAME
8 ----
9 dracut.conf - configuration file(s) for dracut
10
11 SYNOPSIS
12 --------
13 _/etc/dracut.conf_ _/etc/dracut.conf.d/*.conf_ _/usr/lib/dracut/dracut.conf.d/*.conf_
14
15 Description
16 -----------
17 _dracut.conf_ is loaded during the initialisation phase of dracut. Command line
18 parameter will overwrite any values set here.
19
20 _*.conf_ files are read from /usr/lib/dracut/dracut.conf.d and /etc/dracut.conf.d.
21 Files with the same name in /etc/dracut.conf.d will replace files in /usr/lib/dracut/dracut.conf.d.
22 The files are then read in alphanumerical order and will overwrite parameters set in
23 _/etc/dracut.conf_. Each line specifies an attribute and a value. A '#'
24 indicates the beginning of a comment; following characters, up to the end of the
25 line are not interpreted.
26
27 dracut command line options will overwrite any values set here.
28
29 Configuration files must have the extension .conf; other extensions are ignored.
30
31 *dracutmodules+=*" __<dracut modules>__ "::
32 Specify a space-separated list of dracut modules to call when building the
33 initramfs. Modules are located in _/usr/lib/dracut/modules.d_.
34
35 *omit_dracutmodules+=*" __<dracut modules>__ "::
36 Omit a space-separated list of dracut modules.
37
38 *add_dracutmodules+=*" __<dracut modules>__ "::
39 Add a space-separated list of dracut modules.
40
41 *drivers+=*" __<kernel modules>__ "::
42 Specify a space-separated list of kernel modules to exclusively include in
43 the initramfs. The kernel modules have to be specified without the ".ko"
44 suffix.
45
46 *add_drivers+=*" __<kernel modules>__ "::
47 Specify a space-separated list of kernel modules to add to the initramfs.
48 The kernel modules have to be specified without the ".ko" suffix.
49
50 *omit_drivers+=*" __<kernel modules>__ "::
51 Specify a space-separated list of kernel modules not to add to the
52 initramfs. The kernel modules have to be specified without the ".ko" suffix.
53
54 *filesystems+=*" __<filesystem names>__ "::
55 Specify a space-separated list of kernel filesystem modules to exclusively
56 include in the generic initramfs.
57
58 *drivers_dir=*"__<kernel modules directory>__"::
59 Specify the directory, where to look for kernel modules
60
61 *fw_dir+=*" :__<dir>__[:__<dir>__ ...] "::
62 Specify additional directories, where to look for firmwares, separated by :
63
64 *install_items+=*" __<file>__[ __<file>__ ...] "::
65 Specify additional files to include in the initramfs, separated by spaces.
66
67 *do_strip=*"__{yes|no}__"::
68 Strip binaries in the initramfs (default=yes)
69
70 *do_prelink=*"__{yes|no}__"::
71 Prelink binaries in the initramfs (default=yes)
72
73 *hostonly=*"__{yes|no}__"::
74 Host-Only mode: Install only what is needed for booting the local host
75 instead of a generic host and generate host-specific configuration.
76
77 *persistent_policy=*"__<policy>__"::
78 Use _<policy>_ to address disks and partitions.
79 _<policy>_ can be any directory name found in /dev/disk.
80 E.g. "by-uuid", "by-label"
81
82 *tmpdir=*"__<temporary directory>__"::
83 Specify temporary directory to use.
84
85 [WARNING]
86 ====
87 If chrooted to another root other than the real root device, use --fstab and provide a valid _/etc/fstab_.
88 ====
89
90 *use_fstab=*"__{yes|no}__"::
91 Use _/etc/fstab_ instead of _/proc/self/mountinfo_.
92
93 *add_fstab+=*" __<filename>__ "::
94 Add entries of __<filename>__ to the initramfs /etc/fstab.
95
96 *add_device+=*" __<device>__ "::
97 Bring up _<device>_ in initramfs, _<device>_ should be the device name.
98 This can be useful in hostonly mode for resume support when your swap is on
99 LVM an encrypted partition.
100
101 *mdadmconf=*"__{yes|no}__"::
102 Include local _/etc/mdadm.conf_ (default=yes)
103
104 *lvmconf=*"__{yes|no}__"::
105 Include local _/etc/lvm/lvm.conf_ (default=yes)
106
107 *fscks=*" __<fsck tools>__ "::
108 Add a space-separated list of fsck tools. If nothing is specified, the
109 default is: "umount mount /sbin/fsck* xfs_db xfs_check xfs_repair e2fsck
110 jfs_fsck reiserfsck btrfsck". The installation is opportunistic
111 (non-existing tools are ignored).
112
113 *nofscks=*"__{yes|no}__"::
114 If specified, inhibit installation of any fsck tools.
115
116 *ro_mnt=*"__{yes|no}__"::
117 Mount _/_ and _/usr_ read-only by default.
118
119 *kernel_cmdline=*"__parameters__"::
120 Specify default kernel command line parameters
121
122 *kernel_only=*"__{yes|no}__"::
123 Only install kernel drivers and firmware files. (default=no)
124
125 *no_kernel=*"{yes|no}"::
126 Do not install kernel drivers and firmware files (default=no)
127
128 *early_microcode=*"{yes|no}"::
129 Combine early microcode with ramdisk (default=no)
130
131 *stdloglvl*="__\{0-6\}__"::
132 Set logging to standard error level.
133
134 *sysloglvl*="__\{0-6\}__"::
135 Set logging to syslog level.
136
137 *fileloglvl=*"__\{0-6\}__"::
138 Set logging to file level.
139
140 *logfile=*"__<file>__"::
141 Path to log file.
142
143 *show_modules=*"__{yes|no}__"::
144 Print the name of the included modules to standard output during build.
145
146 Files
147 -----
148 _/etc/dracut.conf_::
149 Old configuration file. You better use your own file in
150 _/etc/dracut.conf.d/_.
151
152 _/etc/dracut.conf.d/_::
153 Any _/etc/dracut.conf.d/*.conf_ file can overwrite the values in
154 _/etc/dracut.conf_. The configuration files are read in alphanumerical
155 order.
156
157 AUTHOR
158 ------
159 Harald Hoyer
160
161 See Also
162 --------
163 *dracut*(8) *dracut.cmdline*(7)
164