* Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com>
* Copyright 2008 Colin McCabe <colin@cozybit.com>
* Copyright 2015-2017 Intel Deutschland GmbH
- * Copyright (C) 2018 Intel Corporation
+ * Copyright (C) 2018-2019 Intel Corporation
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* FILS shared key authentication offload should be able to construct the
* authentication and association frames for FILS shared key authentication and
* eventually do a key derivation as per IEEE 802.11ai. The below additional
- * parameters should be given to driver in %NL80211_CMD_CONNECT.
+ * parameters should be given to driver in %NL80211_CMD_CONNECT and/or in
+ * %NL80211_CMD_UPDATE_CONNECT_PARAMS.
* %NL80211_ATTR_FILS_ERP_USERNAME - used to construct keyname_nai
* %NL80211_ATTR_FILS_ERP_REALM - used to construct keyname_nai
* %NL80211_ATTR_FILS_ERP_NEXT_SEQ_NUM - used to construct erp message
* as specified in IETF RFC 6696.
*
* When FILS shared key authentication is completed, driver needs to provide the
- * below additional parameters to userspace.
+ * below additional parameters to userspace, which can be either after setting
+ * up a connection or after roaming.
* %NL80211_ATTR_FILS_KEK - used for key renewal
* %NL80211_ATTR_FILS_ERP_NEXT_SEQ_NUM - used in further EAP-RP exchanges
* %NL80211_ATTR_PMKID - used to identify the PMKSA used/generated
* only the %NL80211_ATTR_IE data is used and updated with this command.
*
* @NL80211_CMD_SET_PMK: For offloaded 4-Way handshake, set the PMK or PMK-R0
- * for the given authenticator address (specified with &NL80211_ATTR_MAC).
- * When &NL80211_ATTR_PMKR0_NAME is set, &NL80211_ATTR_PMK specifies the
+ * for the given authenticator address (specified with %NL80211_ATTR_MAC).
+ * When %NL80211_ATTR_PMKR0_NAME is set, %NL80211_ATTR_PMK specifies the
* PMK-R0, otherwise it specifies the PMK.
* @NL80211_CMD_DEL_PMK: For offloaded 4-Way handshake, delete the previously
* configured PMK for the authenticator address identified by
- * &NL80211_ATTR_MAC.
+ * %NL80211_ATTR_MAC.
* @NL80211_CMD_PORT_AUTHORIZED: An event that indicates that the 4 way
* handshake was completed successfully by the driver. The BSSID is
- * specified with &NL80211_ATTR_MAC. Drivers that support 4 way handshake
+ * specified with %NL80211_ATTR_MAC. Drivers that support 4 way handshake
* offload should send this event after indicating 802.11 association with
- * &NL80211_CMD_CONNECT or &NL80211_CMD_ROAM. If the 4 way handshake failed
- * &NL80211_CMD_DISCONNECT should be indicated instead.
+ * %NL80211_CMD_CONNECT or %NL80211_CMD_ROAM. If the 4 way handshake failed
+ * %NL80211_CMD_DISCONNECT should be indicated instead.
*
* @NL80211_CMD_CONTROL_PORT_FRAME: Control Port (e.g. PAE) frame TX request
* and RX notification. This command is used both as a request to transmit
* initiated the connection through the connect request.
*
* @NL80211_CMD_STA_OPMODE_CHANGED: An event that notify station's
- * ht opmode or vht opmode changes using any of &NL80211_ATTR_SMPS_MODE,
- * &NL80211_ATTR_CHANNEL_WIDTH,&NL80211_ATTR_NSS attributes with its
- * address(specified in &NL80211_ATTR_MAC).
+ * ht opmode or vht opmode changes using any of %NL80211_ATTR_SMPS_MODE,
+ * %NL80211_ATTR_CHANNEL_WIDTH,%NL80211_ATTR_NSS attributes with its
+ * address(specified in %NL80211_ATTR_MAC).
+ *
+ * @NL80211_CMD_GET_FTM_RESPONDER_STATS: Retrieve FTM responder statistics, in
+ * the %NL80211_ATTR_FTM_RESPONDER_STATS attribute.
+ *
+ * @NL80211_CMD_PEER_MEASUREMENT_START: start a (set of) peer measurement(s)
+ * with the given parameters, which are encapsulated in the nested
+ * %NL80211_ATTR_PEER_MEASUREMENTS attribute. Optionally, MAC address
+ * randomization may be enabled and configured by specifying the
+ * %NL80211_ATTR_MAC and %NL80211_ATTR_MAC_MASK attributes.
+ * If a timeout is requested, use the %NL80211_ATTR_TIMEOUT attribute.
+ * A u64 cookie for further %NL80211_ATTR_COOKIE use is is returned in
+ * the netlink extended ack message.
+ *
+ * To cancel a measurement, close the socket that requested it.
+ *
+ * Measurement results are reported to the socket that requested the
+ * measurement using @NL80211_CMD_PEER_MEASUREMENT_RESULT when they
+ * become available, so applications must ensure a large enough socket
+ * buffer size.
+ *
+ * Depending on driver support it may or may not be possible to start
+ * multiple concurrent measurements.
+ * @NL80211_CMD_PEER_MEASUREMENT_RESULT: This command number is used for the
+ * result notification from the driver to the requesting socket.
+ * @NL80211_CMD_PEER_MEASUREMENT_COMPLETE: Notification only, indicating that
+ * the measurement completed, using the measurement cookie
+ * (%NL80211_ATTR_COOKIE).
+ *
+ * @NL80211_CMD_NOTIFY_RADAR: Notify the kernel that a radar signal was
+ * detected and reported by a neighboring device on the channel
+ * indicated by %NL80211_ATTR_WIPHY_FREQ and other attributes
+ * determining the width and type.
+ *
+ * @NL80211_CMD_UPDATE_OWE_INFO: This interface allows the host driver to
+ * offload OWE processing to user space. This intends to support
+ * OWE AKM by the host drivers that implement SME but rely
+ * on the user space for the cryptographic/DH IE processing in AP mode.
+ *
+ * @NL80211_CMD_PROBE_MESH_LINK: The requirement for mesh link metric
+ * refreshing, is that from one mesh point we be able to send some data
+ * frames to other mesh points which are not currently selected as a
+ * primary traffic path, but which are only 1 hop away. The absence of
+ * the primary path to the chosen node makes it necessary to apply some
+ * form of marking on a chosen packet stream so that the packets can be
+ * properly steered to the selected node for testing, and not by the
+ * regular mesh path lookup. Further, the packets must be of type data
+ * so that the rate control (often embedded in firmware) is used for
+ * rate selection.
+ *
+ * Here attribute %NL80211_ATTR_MAC is used to specify connected mesh
+ * peer MAC address and %NL80211_ATTR_FRAME is used to specify the frame
+ * content. The frame is ethernet data.
*
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
NL80211_CMD_CONTROL_PORT_FRAME,
+ NL80211_CMD_GET_FTM_RESPONDER_STATS,
+
+ NL80211_CMD_PEER_MEASUREMENT_START,
+ NL80211_CMD_PEER_MEASUREMENT_RESULT,
+ NL80211_CMD_PEER_MEASUREMENT_COMPLETE,
+
+ NL80211_CMD_NOTIFY_RADAR,
+
+ NL80211_CMD_UPDATE_OWE_INFO,
+
+ NL80211_CMD_PROBE_MESH_LINK,
+
/* add new commands above here */
/* used to define NL80211_CMD_MAX below */
* (a u32 with flags from &enum nl80211_wpa_versions).
* @NL80211_ATTR_AKM_SUITES: Used with CONNECT, ASSOCIATE, and NEW_BEACON to
* indicate which key management algorithm(s) to use (an array of u32).
+ * This attribute is also sent in response to @NL80211_CMD_GET_WIPHY,
+ * indicating the supported AKM suites, intended for specific drivers which
+ * implement SME and have constraints on which AKMs are supported and also
+ * the cases where an AKM support is offloaded to the driver/firmware.
+ * If there is no such notification from the driver, user space should
+ * assume the driver supports all the AKM suites.
*
* @NL80211_ATTR_REQ_IE: (Re)association request information elements as
* sent out by the card, for ROAM and successful CONNECT events.
* the values passed in @NL80211_ATTR_SCAN_SSIDS (eg. if an SSID
* is included in the probe request, but the match attributes
* will never let it go through), -EINVAL may be returned.
- * If ommited, no filtering is done.
+ * If omitted, no filtering is done.
*
* @NL80211_ATTR_INTERFACE_COMBINATIONS: Nested attribute listing the supported
* interface combinations. In each nested item, it contains attributes
*
* @NL80211_ATTR_INACTIVITY_TIMEOUT: timeout value in seconds, this can be
* used by the drivers which has MLME in firmware and does not have support
- * to report per station tx/rx activity to free up the staion entry from
+ * to report per station tx/rx activity to free up the station entry from
* the list. This needs to be used when the driver advertises the
* capability to timeout the stations.
*
*
* @NL80211_ATTR_SCHED_SCAN_RSSI_ADJUST: When present the RSSI level for BSSs in
* the specified band is to be adjusted before doing
- * %NL80211_ATTR_SCHED_SCAN_RELATIVE_RSSI based comparision to figure out
+ * %NL80211_ATTR_SCHED_SCAN_RELATIVE_RSSI based comparison to figure out
* better BSSs. The attribute value is a packed structure
* value as specified by &struct nl80211_bss_select_rssi_adjust.
*
* @NL80211_ATTR_EXTERNAL_AUTH_ACTION: Identify the requested external
* authentication operation (u32 attribute with an
* &enum nl80211_external_auth_action value). This is used with the
- * &NL80211_CMD_EXTERNAL_AUTH request event.
+ * %NL80211_CMD_EXTERNAL_AUTH request event.
* @NL80211_ATTR_EXTERNAL_AUTH_SUPPORT: Flag attribute indicating that the user
- * space supports external authentication. This attribute shall be used
- * only with %NL80211_CMD_CONNECT request. The driver may offload
- * authentication processing to user space if this capability is indicated
- * in NL80211_CMD_CONNECT requests from the user space.
+ * space supports external authentication. This attribute shall be used
+ * with %NL80211_CMD_CONNECT and %NL80211_CMD_START_AP request. The driver
+ * may offload authentication processing to user space if this capability
+ * is indicated in the respective requests from the user space.
*
* @NL80211_ATTR_NSS: Station's New/updated RX_NSS value notified using this
* u8 attribute. This is used with %NL80211_CMD_STA_OPMODE_CHANGED.
* enforced.
* @NL80211_ATTR_TXQ_QUANTUM: TXQ scheduler quantum (bytes). Number of bytes
* a flow is assigned on each round of the DRR scheduler.
+ * @NL80211_ATTR_HE_CAPABILITY: HE Capability information element (from
+ * association request when used with NL80211_CMD_NEW_STATION). Can be set
+ * only if %NL80211_STA_FLAG_WME is set.
+ *
+ * @NL80211_ATTR_FTM_RESPONDER: nested attribute which user-space can include
+ * in %NL80211_CMD_START_AP or %NL80211_CMD_SET_BEACON for fine timing
+ * measurement (FTM) responder functionality and containing parameters as
+ * possible, see &enum nl80211_ftm_responder_attr
+ *
+ * @NL80211_ATTR_FTM_RESPONDER_STATS: Nested attribute with FTM responder
+ * statistics, see &enum nl80211_ftm_responder_stats.
+ *
+ * @NL80211_ATTR_TIMEOUT: Timeout for the given operation in milliseconds (u32),
+ * if the attribute is not given no timeout is requested. Note that 0 is an
+ * invalid value.
+ *
+ * @NL80211_ATTR_PEER_MEASUREMENTS: peer measurements request (and result)
+ * data, uses nested attributes specified in
+ * &enum nl80211_peer_measurement_attrs.
+ * This is also used for capability advertisement in the wiphy information,
+ * with the appropriate sub-attributes.
+ *
+ * @NL80211_ATTR_AIRTIME_WEIGHT: Station's weight when scheduled by the airtime
+ * scheduler.
+ *
+ * @NL80211_ATTR_STA_TX_POWER_SETTING: Transmit power setting type (u8) for
+ * station associated with the AP. See &enum nl80211_tx_power_setting for
+ * possible values.
+ * @NL80211_ATTR_STA_TX_POWER: Transmit power level (s16) in dBm units. This
+ * allows to set Tx power for a station. If this attribute is not included,
+ * the default per-interface tx power setting will be overriding. Driver
+ * should be picking up the lowest tx power, either tx power per-interface
+ * or per-station.
*
* @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
NL80211_ATTR_TXQ_MEMORY_LIMIT,
NL80211_ATTR_TXQ_QUANTUM,
+ NL80211_ATTR_HE_CAPABILITY,
+
+ NL80211_ATTR_FTM_RESPONDER,
+
+ NL80211_ATTR_FTM_RESPONDER_STATS,
+
+ NL80211_ATTR_TIMEOUT,
+
+ NL80211_ATTR_PEER_MEASUREMENTS,
+
+ NL80211_ATTR_AIRTIME_WEIGHT,
+ NL80211_ATTR_STA_TX_POWER_SETTING,
+ NL80211_ATTR_STA_TX_POWER,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
#define NL80211_ATTR_KEYS NL80211_ATTR_KEYS
#define NL80211_ATTR_FEATURE_FLAGS NL80211_ATTR_FEATURE_FLAGS
+#define NL80211_WIPHY_NAME_MAXLEN 64
+
#define NL80211_MAX_SUPP_RATES 32
#define NL80211_MAX_SUPP_HT_RATES 77
-#define NL80211_MAX_SUPP_REG_RULES 64
+#define NL80211_MAX_SUPP_REG_RULES 128
#define NL80211_TKIP_DATA_OFFSET_ENCR_KEY 0
#define NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY 16
#define NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY 24
#define NL80211_HT_CAPABILITY_LEN 26
#define NL80211_VHT_CAPABILITY_LEN 12
-
+#define NL80211_HE_MIN_CAPABILITY_LEN 16
+#define NL80211_HE_MAX_CAPABILITY_LEN 51
#define NL80211_MAX_NR_CIPHER_SUITES 5
#define NL80211_MAX_NR_AKM_SUITES 2
__u32 set;
} __attribute__((packed));
+/**
+ * enum nl80211_he_gi - HE guard interval
+ * @NL80211_RATE_INFO_HE_GI_0_8: 0.8 usec
+ * @NL80211_RATE_INFO_HE_GI_1_6: 1.6 usec
+ * @NL80211_RATE_INFO_HE_GI_3_2: 3.2 usec
+ */
+enum nl80211_he_gi {
+ NL80211_RATE_INFO_HE_GI_0_8,
+ NL80211_RATE_INFO_HE_GI_1_6,
+ NL80211_RATE_INFO_HE_GI_3_2,
+};
+
+/**
+ * enum nl80211_he_ru_alloc - HE RU allocation values
+ * @NL80211_RATE_INFO_HE_RU_ALLOC_26: 26-tone RU allocation
+ * @NL80211_RATE_INFO_HE_RU_ALLOC_52: 52-tone RU allocation
+ * @NL80211_RATE_INFO_HE_RU_ALLOC_106: 106-tone RU allocation
+ * @NL80211_RATE_INFO_HE_RU_ALLOC_242: 242-tone RU allocation
+ * @NL80211_RATE_INFO_HE_RU_ALLOC_484: 484-tone RU allocation
+ * @NL80211_RATE_INFO_HE_RU_ALLOC_996: 996-tone RU allocation
+ * @NL80211_RATE_INFO_HE_RU_ALLOC_2x996: 2x996-tone RU allocation
+ */
+enum nl80211_he_ru_alloc {
+ NL80211_RATE_INFO_HE_RU_ALLOC_26,
+ NL80211_RATE_INFO_HE_RU_ALLOC_52,
+ NL80211_RATE_INFO_HE_RU_ALLOC_106,
+ NL80211_RATE_INFO_HE_RU_ALLOC_242,
+ NL80211_RATE_INFO_HE_RU_ALLOC_484,
+ NL80211_RATE_INFO_HE_RU_ALLOC_996,
+ NL80211_RATE_INFO_HE_RU_ALLOC_2x996,
+};
+
/**
* enum nl80211_rate_info - bitrate information
*
* @NL80211_RATE_INFO_5_MHZ_WIDTH: 5 MHz width - note that this is
* a legacy rate and will be reported as the actual bitrate, i.e.
* a quarter of the base (20 MHz) rate
+ * @NL80211_RATE_INFO_HE_MCS: HE MCS index (u8, 0-11)
+ * @NL80211_RATE_INFO_HE_NSS: HE NSS value (u8, 1-8)
+ * @NL80211_RATE_INFO_HE_GI: HE guard interval identifier
+ * (u8, see &enum nl80211_he_gi)
+ * @NL80211_RATE_INFO_HE_DCM: HE DCM value (u8, 0/1)
+ * @NL80211_RATE_INFO_RU_ALLOC: HE RU allocation, if not present then
+ * non-OFDMA was used (u8, see &enum nl80211_he_ru_alloc)
* @__NL80211_RATE_INFO_AFTER_LAST: internal use
*/
enum nl80211_rate_info {
NL80211_RATE_INFO_160_MHZ_WIDTH,
NL80211_RATE_INFO_10_MHZ_WIDTH,
NL80211_RATE_INFO_5_MHZ_WIDTH,
+ NL80211_RATE_INFO_HE_MCS,
+ NL80211_RATE_INFO_HE_NSS,
+ NL80211_RATE_INFO_HE_GI,
+ NL80211_RATE_INFO_HE_DCM,
+ NL80211_RATE_INFO_HE_RU_ALLOC,
/* keep last */
__NL80211_RATE_INFO_AFTER_LAST,
* received from the station (u64, usec)
* @NL80211_STA_INFO_PAD: attribute used for padding for 64-bit alignment
* @NL80211_STA_INFO_ACK_SIGNAL: signal strength of the last ACK frame(u8, dBm)
- * @NL80211_STA_INFO_DATA_ACK_SIGNAL_AVG: avg signal strength of (data)
- * ACK frame (s8, dBm)
+ * @NL80211_STA_INFO_ACK_SIGNAL_AVG: avg signal strength of ACK frames (s8, dBm)
+ * @NL80211_STA_INFO_RX_MPDUS: total number of received packets (MPDUs)
+ * (u32, from this station)
+ * @NL80211_STA_INFO_FCS_ERROR_COUNT: total number of packets (MPDUs) received
+ * with an FCS error (u32, from this station). This count may not include
+ * some packets with an FCS error due to TA corruption. Hence this counter
+ * might not be fully accurate.
+ * @NL80211_STA_INFO_CONNECTED_TO_GATE: set to true if STA has a path to a
+ * mesh gate (u8, 0 or 1)
+ * @NL80211_STA_INFO_TX_DURATION: aggregate PPDU duration for all frames
+ * sent to the station (u64, usec)
+ * @NL80211_STA_INFO_AIRTIME_WEIGHT: current airtime weight for station (u16)
+ * @NL80211_STA_INFO_AIRTIME_LINK_METRIC: airtime link metric for mesh station
* @__NL80211_STA_INFO_AFTER_LAST: internal
* @NL80211_STA_INFO_MAX: highest possible station info attribute
*/
NL80211_STA_INFO_RX_DURATION,
NL80211_STA_INFO_PAD,
NL80211_STA_INFO_ACK_SIGNAL,
- NL80211_STA_INFO_DATA_ACK_SIGNAL_AVG,
+ NL80211_STA_INFO_ACK_SIGNAL_AVG,
+ NL80211_STA_INFO_RX_MPDUS,
+ NL80211_STA_INFO_FCS_ERROR_COUNT,
+ NL80211_STA_INFO_CONNECTED_TO_GATE,
+ NL80211_STA_INFO_TX_DURATION,
+ NL80211_STA_INFO_AIRTIME_WEIGHT,
+ NL80211_STA_INFO_AIRTIME_LINK_METRIC,
/* keep last */
__NL80211_STA_INFO_AFTER_LAST,
NL80211_STA_INFO_MAX = __NL80211_STA_INFO_AFTER_LAST - 1
};
+/* we renamed this - stay compatible */
+#define NL80211_STA_INFO_DATA_ACK_SIGNAL_AVG NL80211_STA_INFO_ACK_SIGNAL_AVG
+
+
/**
* enum nl80211_tid_stats - per TID statistics attributes
* @__NL80211_TID_STATS_INVALID: attribute number 0 is reserved
* &enum nl80211_mpath_flags;
* @NL80211_MPATH_INFO_DISCOVERY_TIMEOUT: total path discovery timeout, in msec
* @NL80211_MPATH_INFO_DISCOVERY_RETRIES: mesh path discovery retries
+ * @NL80211_MPATH_INFO_HOP_COUNT: hop count to destination
+ * @NL80211_MPATH_INFO_PATH_CHANGE: total number of path changes to destination
* @NL80211_MPATH_INFO_MAX: highest mesh path information attribute number
- * currently defind
+ * currently defined
* @__NL80211_MPATH_INFO_AFTER_LAST: internal use
*/
enum nl80211_mpath_info {
NL80211_MPATH_INFO_FLAGS,
NL80211_MPATH_INFO_DISCOVERY_TIMEOUT,
NL80211_MPATH_INFO_DISCOVERY_RETRIES,
+ NL80211_MPATH_INFO_HOP_COUNT,
+ NL80211_MPATH_INFO_PATH_CHANGE,
/* keep last */
__NL80211_MPATH_INFO_AFTER_LAST,
NL80211_MPATH_INFO_MAX = __NL80211_MPATH_INFO_AFTER_LAST - 1
};
+/**
+ * enum nl80211_band_iftype_attr - Interface type data attributes
+ *
+ * @__NL80211_BAND_IFTYPE_ATTR_INVALID: attribute number 0 is reserved
+ * @NL80211_BAND_IFTYPE_ATTR_IFTYPES: nested attribute containing a flag attribute
+ * for each interface type that supports the band data
+ * @NL80211_BAND_IFTYPE_ATTR_HE_CAP_MAC: HE MAC capabilities as in HE
+ * capabilities IE
+ * @NL80211_BAND_IFTYPE_ATTR_HE_CAP_PHY: HE PHY capabilities as in HE
+ * capabilities IE
+ * @NL80211_BAND_IFTYPE_ATTR_HE_CAP_MCS_SET: HE supported NSS/MCS as in HE
+ * capabilities IE
+ * @NL80211_BAND_IFTYPE_ATTR_HE_CAP_PPE: HE PPE thresholds information as
+ * defined in HE capabilities IE
+ * @NL80211_BAND_IFTYPE_ATTR_MAX: highest band HE capability attribute currently
+ * defined
+ * @__NL80211_BAND_IFTYPE_ATTR_AFTER_LAST: internal use
+ */
+enum nl80211_band_iftype_attr {
+ __NL80211_BAND_IFTYPE_ATTR_INVALID,
+
+ NL80211_BAND_IFTYPE_ATTR_IFTYPES,
+ NL80211_BAND_IFTYPE_ATTR_HE_CAP_MAC,
+ NL80211_BAND_IFTYPE_ATTR_HE_CAP_PHY,
+ NL80211_BAND_IFTYPE_ATTR_HE_CAP_MCS_SET,
+ NL80211_BAND_IFTYPE_ATTR_HE_CAP_PPE,
+
+ /* keep last */
+ __NL80211_BAND_IFTYPE_ATTR_AFTER_LAST,
+ NL80211_BAND_IFTYPE_ATTR_MAX = __NL80211_BAND_IFTYPE_ATTR_AFTER_LAST - 1
+};
+
/**
* enum nl80211_band_attr - band attributes
* @__NL80211_BAND_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_BAND_ATTR_VHT_MCS_SET: 32-byte attribute containing the MCS set as
* defined in 802.11ac
* @NL80211_BAND_ATTR_VHT_CAPA: VHT capabilities, as in the HT information IE
+ * @NL80211_BAND_ATTR_IFTYPE_DATA: nested array attribute, with each entry using
+ * attributes from &enum nl80211_band_iftype_attr
* @NL80211_BAND_ATTR_MAX: highest band attribute currently defined
* @__NL80211_BAND_ATTR_AFTER_LAST: internal use
*/
NL80211_BAND_ATTR_VHT_MCS_SET,
NL80211_BAND_ATTR_VHT_CAPA,
+ NL80211_BAND_ATTR_IFTYPE_DATA,
/* keep last */
__NL80211_BAND_ATTR_AFTER_LAST,
* value as specified by &struct nl80211_bss_select_rssi_adjust.
* @NL80211_SCHED_SCAN_MATCH_ATTR_BSSID: BSSID to be used for matching
* (this cannot be used together with SSID).
+ * @NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI: Nested attribute that carries the
+ * band specific minimum rssi thresholds for the bands defined in
+ * enum nl80211_band. The minimum rssi threshold value(s32) specific to a
+ * band shall be encapsulated in attribute with type value equals to one
+ * of the NL80211_BAND_* defined in enum nl80211_band. For example, the
+ * minimum rssi threshold value for 2.4GHZ band shall be encapsulated
+ * within an attribute of type NL80211_BAND_2GHZ. And one or more of such
+ * attributes will be nested within this attribute.
* @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter
* attribute number currently defined
* @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use
NL80211_SCHED_SCAN_MATCH_ATTR_RELATIVE_RSSI,
NL80211_SCHED_SCAN_MATCH_ATTR_RSSI_ADJUST,
NL80211_SCHED_SCAN_MATCH_ATTR_BSSID,
+ NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI,
/* keep last */
__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST,
* @NL80211_RRF_AUTO_BW: maximum available bandwidth should be calculated
* base on contiguous rules and wider channels will be allowed to cross
* multiple contiguous/overlapping frequency ranges.
- * @NL80211_RRF_IR_CONCURRENT: See &NL80211_FREQUENCY_ATTR_IR_CONCURRENT
+ * @NL80211_RRF_IR_CONCURRENT: See %NL80211_FREQUENCY_ATTR_IR_CONCURRENT
* @NL80211_RRF_NO_HT40MINUS: channels can't be used in HT40- operation
* @NL80211_RRF_NO_HT40PLUS: channels can't be used in HT40+ operation
* @NL80211_RRF_NO_80MHZ: 80MHz operation not allowed
* remove it from the STA's list of peers. You may set this to 0 to disable
* the removal of the STA. Default is 30 minutes.
*
+ * @NL80211_MESHCONF_CONNECTED_TO_GATE: If set to true then this mesh STA
+ * will advertise that it is connected to a gate in the mesh formation
+ * field. If left unset then the mesh formation field will only
+ * advertise such if there is an active root mesh path.
+ *
* @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use
*/
enum nl80211_meshconf_params {
NL80211_MESHCONF_POWER_MODE,
NL80211_MESHCONF_AWAKE_WINDOW,
NL80211_MESHCONF_PLINK_TIMEOUT,
+ NL80211_MESHCONF_CONNECTED_TO_GATE,
/* keep last */
__NL80211_MESHCONF_ATTR_AFTER_LAST,
NL80211_CHAN_HT40PLUS
};
+/**
+ * enum nl80211_key_mode - Key mode
+ *
+ * @NL80211_KEY_RX_TX: (Default)
+ * Key can be used for Rx and Tx immediately
+ *
+ * The following modes can only be selected for unicast keys and when the
+ * driver supports @NL80211_EXT_FEATURE_EXT_KEY_ID:
+ *
+ * @NL80211_KEY_NO_TX: Only allowed in combination with @NL80211_CMD_NEW_KEY:
+ * Unicast key can only be used for Rx, Tx not allowed, yet
+ * @NL80211_KEY_SET_TX: Only allowed in combination with @NL80211_CMD_SET_KEY:
+ * The unicast key identified by idx and mac is cleared for Tx and becomes
+ * the preferred Tx key for the station.
+ */
+enum nl80211_key_mode {
+ NL80211_KEY_RX_TX,
+ NL80211_KEY_NO_TX,
+ NL80211_KEY_SET_TX
+};
+
/**
* enum nl80211_chan_width - channel width definitions
*
* @NL80211_KEY_DEFAULT_TYPES: A nested attribute containing flags
* attributes, specifying what a key should be set as default as.
* See &enum nl80211_key_default_types.
+ * @NL80211_KEY_MODE: the mode from enum nl80211_key_mode.
+ * Defaults to @NL80211_KEY_RX_TX.
+ *
* @__NL80211_KEY_AFTER_LAST: internal
* @NL80211_KEY_MAX: highest key attribute
*/
NL80211_KEY_DEFAULT_MGMT,
NL80211_KEY_TYPE,
NL80211_KEY_DEFAULT_TYPES,
+ NL80211_KEY_MODE,
/* keep last */
__NL80211_KEY_AFTER_LAST,
* enum nl80211_band - Frequency band
* @NL80211_BAND_2GHZ: 2.4 GHz ISM band
* @NL80211_BAND_5GHZ: around 5 GHz band (4.9 - 5.7 GHz)
- * @NL80211_BAND_60GHZ: around 60 GHz band (58.32 - 64.80 GHz)
+ * @NL80211_BAND_60GHZ: around 60 GHz band (58.32 - 69.12 GHz)
* @NUM_NL80211_BANDS: number of bands, avoid using this in userspace
* since newer kernel versions may support more bands
*/
* numbers = [ #{STA} <= 1, #{P2P-client,P2P-GO} <= 3 ], max = 4
* => allows a STA plus three P2P interfaces
*
- * The list of these four possiblities could completely be contained
+ * The list of these four possibilities could completely be contained
* within the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute to indicate
* that any of these groups must match.
*
* enum nl80211_plink_state - state of a mesh peer link finite state machine
*
* @NL80211_PLINK_LISTEN: initial state, considered the implicit
- * state of non existant mesh peer links
+ * state of non existent mesh peer links
* @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to
* this mesh peer
* @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received
* "radar detected" event.
* @NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211: Driver supports sending and
* receiving control port frames over nl80211 instead of the netdevice.
- * @NL80211_EXT_FEATURE_DATA_ACK_SIGNAL_SUPPORT: This Driver support data ack
- * rssi if firmware support, this flag is to intimate about ack rssi
- * support to nl80211.
+ * @NL80211_EXT_FEATURE_ACK_SIGNAL_SUPPORT: This driver/device supports
+ * (average) ACK signal strength reporting.
* @NL80211_EXT_FEATURE_TXQS: Driver supports FQ-CoDel-enabled intermediate
* TXQs.
+ * @NL80211_EXT_FEATURE_SCAN_RANDOM_SN: Driver/device supports randomizing the
+ * SN in probe request frames if requested by %NL80211_SCAN_FLAG_RANDOM_SN.
+ * @NL80211_EXT_FEATURE_SCAN_MIN_PREQ_CONTENT: Driver/device can omit all data
+ * except for supported rates from the probe request content if requested
+ * by the %NL80211_SCAN_FLAG_MIN_PREQ_CONTENT flag.
+ * @NL80211_EXT_FEATURE_ENABLE_FTM_RESPONDER: Driver supports enabling fine
+ * timing measurement responder role.
+ *
+ * @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0: Driver/device confirm that they are
+ * able to rekey an in-use key correctly. Userspace must not rekey PTK keys
+ * if this flag is not set. Ignoring this can leak clear text packets and/or
+ * freeze the connection.
+ * @NL80211_EXT_FEATURE_EXT_KEY_ID: Driver supports "Extended Key ID for
+ * Individually Addressed Frames" from IEEE802.11-2016.
+ *
+ * @NL80211_EXT_FEATURE_AIRTIME_FAIRNESS: Driver supports getting airtime
+ * fairness for transmitted packets and has enabled airtime fairness
+ * scheduling.
+ *
+ * @NL80211_EXT_FEATURE_AP_PMKSA_CACHING: Driver/device supports PMKSA caching
+ * (set/del PMKSA operations) in AP mode.
+ *
+ * @NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD: Driver supports
+ * filtering of sched scan results using band specific RSSI thresholds.
+ *
+ * @NL80211_EXT_FEATURE_STA_TX_PWR: This driver supports controlling tx power
+ * to a station.
*
* @NUM_NL80211_EXT_FEATURES: number of extended features.
* @MAX_NL80211_EXT_FEATURES: highest extended feature index.
NL80211_EXT_FEATURE_HIGH_ACCURACY_SCAN,
NL80211_EXT_FEATURE_DFS_OFFLOAD,
NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211,
- NL80211_EXT_FEATURE_DATA_ACK_SIGNAL_SUPPORT,
+ NL80211_EXT_FEATURE_ACK_SIGNAL_SUPPORT,
+ /* we renamed this - stay compatible */
+ NL80211_EXT_FEATURE_DATA_ACK_SIGNAL_SUPPORT = NL80211_EXT_FEATURE_ACK_SIGNAL_SUPPORT,
NL80211_EXT_FEATURE_TXQS,
+ NL80211_EXT_FEATURE_SCAN_RANDOM_SN,
+ NL80211_EXT_FEATURE_SCAN_MIN_PREQ_CONTENT,
+ NL80211_EXT_FEATURE_CAN_REPLACE_PTK0,
+ NL80211_EXT_FEATURE_ENABLE_FTM_RESPONDER,
+ NL80211_EXT_FEATURE_AIRTIME_FAIRNESS,
+ NL80211_EXT_FEATURE_AP_PMKSA_CACHING,
+ NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD,
+ NL80211_EXT_FEATURE_EXT_KEY_ID,
+ NL80211_EXT_FEATURE_STA_TX_PWR,
/* add new features before the definition below */
NUM_NL80211_EXT_FEATURES,
* request parameters IE in the probe request
* @NL80211_SCAN_FLAG_ACCEPT_BCAST_PROBE_RESP: accept broadcast probe responses
* @NL80211_SCAN_FLAG_OCE_PROBE_REQ_HIGH_TX_RATE: send probe request frames at
- * rate of at least 5.5M. In case non OCE AP is dicovered in the channel,
+ * rate of at least 5.5M. In case non OCE AP is discovered in the channel,
* only the first probe req in the channel will be sent in high rate.
* @NL80211_SCAN_FLAG_OCE_PROBE_REQ_DEFERRAL_SUPPRESSION: allow probe request
* tx deferral (dot11FILSProbeDelay shall be set to 15ms)
* possible scan results. This flag hints the driver to use the best
* possible scan configuration to improve the accuracy in scanning.
* Latency and power use may get impacted with this flag.
+ * @NL80211_SCAN_FLAG_RANDOM_SN: randomize the sequence number in probe
+ * request frames from this scan to avoid correlation/tracking being
+ * possible.
+ * @NL80211_SCAN_FLAG_MIN_PREQ_CONTENT: minimize probe request content to
+ * only have supported rates and no additional capabilities (unless
+ * added by userspace explicitly.)
*/
enum nl80211_scan_flags {
NL80211_SCAN_FLAG_LOW_PRIORITY = 1<<0,
NL80211_SCAN_FLAG_LOW_SPAN = 1<<8,
NL80211_SCAN_FLAG_LOW_POWER = 1<<9,
NL80211_SCAN_FLAG_HIGH_ACCURACY = 1<<10,
+ NL80211_SCAN_FLAG_RANDOM_SN = 1<<11,
+ NL80211_SCAN_FLAG_MIN_PREQ_CONTENT = 1<<12,
};
/**
* Used by cfg80211_rx_mgmt()
*
* @NL80211_RXMGMT_FLAG_ANSWERED: frame was answered by device/driver.
+ * @NL80211_RXMGMT_FLAG_EXTERNAL_AUTH: Host driver intends to offload
+ * the authentication. Exclusively defined for host drivers that
+ * advertises the SME functionality but would like the userspace
+ * to handle certain authentication algorithms (e.g. SAE).
*/
enum nl80211_rxmgmt_flags {
NL80211_RXMGMT_FLAG_ANSWERED = 1 << 0,
+ NL80211_RXMGMT_FLAG_EXTERNAL_AUTH = 1 << 1,
};
/*
* @NL80211_NAN_SRF_INCLUDE: present if the include bit of the SRF set.
* This is a flag.
* @NL80211_NAN_SRF_BF: Bloom Filter. Present if and only if
- * &NL80211_NAN_SRF_MAC_ADDRS isn't present. This attribute is binary.
+ * %NL80211_NAN_SRF_MAC_ADDRS isn't present. This attribute is binary.
* @NL80211_NAN_SRF_BF_IDX: index of the Bloom Filter. Mandatory if
- * &NL80211_NAN_SRF_BF is present. This is a u8.
+ * %NL80211_NAN_SRF_BF is present. This is a u8.
* @NL80211_NAN_SRF_MAC_ADDRS: list of MAC addresses for the SRF. Present if
- * and only if &NL80211_NAN_SRF_BF isn't present. This is a nested
+ * and only if %NL80211_NAN_SRF_BF isn't present. This is a nested
* attribute. Each nested attribute is a MAC address.
* @NUM_NL80211_NAN_SRF_ATTR: internal
* @NL80211_NAN_SRF_ATTR_MAX: highest NAN SRF attribute
NL80211_EXTERNAL_AUTH_ABORT,
};
+/**
+ * enum nl80211_ftm_responder_attributes - fine timing measurement
+ * responder attributes
+ * @__NL80211_FTM_RESP_ATTR_INVALID: Invalid
+ * @NL80211_FTM_RESP_ATTR_ENABLED: FTM responder is enabled
+ * @NL80211_FTM_RESP_ATTR_LCI: The content of Measurement Report Element
+ * (9.4.2.22 in 802.11-2016) with type 8 - LCI (9.4.2.22.10),
+ * i.e. starting with the measurement token
+ * @NL80211_FTM_RESP_ATTR_CIVIC: The content of Measurement Report Element
+ * (9.4.2.22 in 802.11-2016) with type 11 - Civic (Section 9.4.2.22.13),
+ * i.e. starting with the measurement token
+ * @__NL80211_FTM_RESP_ATTR_LAST: Internal
+ * @NL80211_FTM_RESP_ATTR_MAX: highest FTM responder attribute.
+ */
+enum nl80211_ftm_responder_attributes {
+ __NL80211_FTM_RESP_ATTR_INVALID,
+
+ NL80211_FTM_RESP_ATTR_ENABLED,
+ NL80211_FTM_RESP_ATTR_LCI,
+ NL80211_FTM_RESP_ATTR_CIVICLOC,
+
+ /* keep last */
+ __NL80211_FTM_RESP_ATTR_LAST,
+ NL80211_FTM_RESP_ATTR_MAX = __NL80211_FTM_RESP_ATTR_LAST - 1,
+};
+
+/*
+ * enum nl80211_ftm_responder_stats - FTM responder statistics
+ *
+ * These attribute types are used with %NL80211_ATTR_FTM_RESPONDER_STATS
+ * when getting FTM responder statistics.
+ *
+ * @__NL80211_FTM_STATS_INVALID: attribute number 0 is reserved
+ * @NL80211_FTM_STATS_SUCCESS_NUM: number of FTM sessions in which all frames
+ * were ssfully answered (u32)
+ * @NL80211_FTM_STATS_PARTIAL_NUM: number of FTM sessions in which part of the
+ * frames were successfully answered (u32)
+ * @NL80211_FTM_STATS_FAILED_NUM: number of failed FTM sessions (u32)
+ * @NL80211_FTM_STATS_ASAP_NUM: number of ASAP sessions (u32)
+ * @NL80211_FTM_STATS_NON_ASAP_NUM: number of non-ASAP sessions (u32)
+ * @NL80211_FTM_STATS_TOTAL_DURATION_MSEC: total sessions durations - gives an
+ * indication of how much time the responder was busy (u64, msec)
+ * @NL80211_FTM_STATS_UNKNOWN_TRIGGERS_NUM: number of unknown FTM triggers -
+ * triggers from initiators that didn't finish successfully the negotiation
+ * phase with the responder (u32)
+ * @NL80211_FTM_STATS_RESCHEDULE_REQUESTS_NUM: number of FTM reschedule requests
+ * - initiator asks for a new scheduling although it already has scheduled
+ * FTM slot (u32)
+ * @NL80211_FTM_STATS_OUT_OF_WINDOW_TRIGGERS_NUM: number of FTM triggers out of
+ * scheduled window (u32)
+ * @NL80211_FTM_STATS_PAD: used for padding, ignore
+ * @__NL80211_TXQ_ATTR_AFTER_LAST: Internal
+ * @NL80211_FTM_STATS_MAX: highest possible FTM responder stats attribute
+ */
+enum nl80211_ftm_responder_stats {
+ __NL80211_FTM_STATS_INVALID,
+ NL80211_FTM_STATS_SUCCESS_NUM,
+ NL80211_FTM_STATS_PARTIAL_NUM,
+ NL80211_FTM_STATS_FAILED_NUM,
+ NL80211_FTM_STATS_ASAP_NUM,
+ NL80211_FTM_STATS_NON_ASAP_NUM,
+ NL80211_FTM_STATS_TOTAL_DURATION_MSEC,
+ NL80211_FTM_STATS_UNKNOWN_TRIGGERS_NUM,
+ NL80211_FTM_STATS_RESCHEDULE_REQUESTS_NUM,
+ NL80211_FTM_STATS_OUT_OF_WINDOW_TRIGGERS_NUM,
+ NL80211_FTM_STATS_PAD,
+
+ /* keep last */
+ __NL80211_FTM_STATS_AFTER_LAST,
+ NL80211_FTM_STATS_MAX = __NL80211_FTM_STATS_AFTER_LAST - 1
+};
+
+/**
+ * enum nl80211_preamble - frame preamble types
+ * @NL80211_PREAMBLE_LEGACY: legacy (HR/DSSS, OFDM, ERP PHY) preamble
+ * @NL80211_PREAMBLE_HT: HT preamble
+ * @NL80211_PREAMBLE_VHT: VHT preamble
+ * @NL80211_PREAMBLE_DMG: DMG preamble
+ */
+enum nl80211_preamble {
+ NL80211_PREAMBLE_LEGACY,
+ NL80211_PREAMBLE_HT,
+ NL80211_PREAMBLE_VHT,
+ NL80211_PREAMBLE_DMG,
+};
+
+/**
+ * enum nl80211_peer_measurement_type - peer measurement types
+ * @NL80211_PMSR_TYPE_INVALID: invalid/unused, needed as we use
+ * these numbers also for attributes
+ *
+ * @NL80211_PMSR_TYPE_FTM: flight time measurement
+ *
+ * @NUM_NL80211_PMSR_TYPES: internal
+ * @NL80211_PMSR_TYPE_MAX: highest type number
+ */
+enum nl80211_peer_measurement_type {
+ NL80211_PMSR_TYPE_INVALID,
+
+ NL80211_PMSR_TYPE_FTM,
+
+ NUM_NL80211_PMSR_TYPES,
+ NL80211_PMSR_TYPE_MAX = NUM_NL80211_PMSR_TYPES - 1
+};
+
+/**
+ * enum nl80211_peer_measurement_status - peer measurement status
+ * @NL80211_PMSR_STATUS_SUCCESS: measurement completed successfully
+ * @NL80211_PMSR_STATUS_REFUSED: measurement was locally refused
+ * @NL80211_PMSR_STATUS_TIMEOUT: measurement timed out
+ * @NL80211_PMSR_STATUS_FAILURE: measurement failed, a type-dependent
+ * reason may be available in the response data
+ */
+enum nl80211_peer_measurement_status {
+ NL80211_PMSR_STATUS_SUCCESS,
+ NL80211_PMSR_STATUS_REFUSED,
+ NL80211_PMSR_STATUS_TIMEOUT,
+ NL80211_PMSR_STATUS_FAILURE,
+};
+
+/**
+ * enum nl80211_peer_measurement_req - peer measurement request attributes
+ * @__NL80211_PMSR_REQ_ATTR_INVALID: invalid
+ *
+ * @NL80211_PMSR_REQ_ATTR_DATA: This is a nested attribute with measurement
+ * type-specific request data inside. The attributes used are from the
+ * enums named nl80211_peer_measurement_<type>_req.
+ * @NL80211_PMSR_REQ_ATTR_GET_AP_TSF: include AP TSF timestamp, if supported
+ * (flag attribute)
+ *
+ * @NUM_NL80211_PMSR_REQ_ATTRS: internal
+ * @NL80211_PMSR_REQ_ATTR_MAX: highest attribute number
+ */
+enum nl80211_peer_measurement_req {
+ __NL80211_PMSR_REQ_ATTR_INVALID,
+
+ NL80211_PMSR_REQ_ATTR_DATA,
+ NL80211_PMSR_REQ_ATTR_GET_AP_TSF,
+
+ /* keep last */
+ NUM_NL80211_PMSR_REQ_ATTRS,
+ NL80211_PMSR_REQ_ATTR_MAX = NUM_NL80211_PMSR_REQ_ATTRS - 1
+};
+
+/**
+ * enum nl80211_peer_measurement_resp - peer measurement response attributes
+ * @__NL80211_PMSR_RESP_ATTR_INVALID: invalid
+ *
+ * @NL80211_PMSR_RESP_ATTR_DATA: This is a nested attribute with measurement
+ * type-specific results inside. The attributes used are from the enums
+ * named nl80211_peer_measurement_<type>_resp.
+ * @NL80211_PMSR_RESP_ATTR_STATUS: u32 value with the measurement status
+ * (using values from &enum nl80211_peer_measurement_status.)
+ * @NL80211_PMSR_RESP_ATTR_HOST_TIME: host time (%CLOCK_BOOTTIME) when the
+ * result was measured; this value is not expected to be accurate to
+ * more than 20ms. (u64, nanoseconds)
+ * @NL80211_PMSR_RESP_ATTR_AP_TSF: TSF of the AP that the interface
+ * doing the measurement is connected to when the result was measured.
+ * This shall be accurately reported if supported and requested
+ * (u64, usec)
+ * @NL80211_PMSR_RESP_ATTR_FINAL: If results are sent to the host partially
+ * (*e.g. with FTM per-burst data) this flag will be cleared on all but
+ * the last result; if all results are combined it's set on the single
+ * result.
+ * @NL80211_PMSR_RESP_ATTR_PAD: padding for 64-bit attributes, ignore
+ *
+ * @NUM_NL80211_PMSR_RESP_ATTRS: internal
+ * @NL80211_PMSR_RESP_ATTR_MAX: highest attribute number
+ */
+enum nl80211_peer_measurement_resp {
+ __NL80211_PMSR_RESP_ATTR_INVALID,
+
+ NL80211_PMSR_RESP_ATTR_DATA,
+ NL80211_PMSR_RESP_ATTR_STATUS,
+ NL80211_PMSR_RESP_ATTR_HOST_TIME,
+ NL80211_PMSR_RESP_ATTR_AP_TSF,
+ NL80211_PMSR_RESP_ATTR_FINAL,
+ NL80211_PMSR_RESP_ATTR_PAD,
+
+ /* keep last */
+ NUM_NL80211_PMSR_RESP_ATTRS,
+ NL80211_PMSR_RESP_ATTR_MAX = NUM_NL80211_PMSR_RESP_ATTRS - 1
+};
+
+/**
+ * enum nl80211_peer_measurement_peer_attrs - peer attributes for measurement
+ * @__NL80211_PMSR_PEER_ATTR_INVALID: invalid
+ *
+ * @NL80211_PMSR_PEER_ATTR_ADDR: peer's MAC address
+ * @NL80211_PMSR_PEER_ATTR_CHAN: channel definition, nested, using top-level
+ * attributes like %NL80211_ATTR_WIPHY_FREQ etc.
+ * @NL80211_PMSR_PEER_ATTR_REQ: This is a nested attribute indexed by
+ * measurement type, with attributes from the
+ * &enum nl80211_peer_measurement_req inside.
+ * @NL80211_PMSR_PEER_ATTR_RESP: This is a nested attribute indexed by
+ * measurement type, with attributes from the
+ * &enum nl80211_peer_measurement_resp inside.
+ *
+ * @NUM_NL80211_PMSR_PEER_ATTRS: internal
+ * @NL80211_PMSR_PEER_ATTR_MAX: highest attribute number
+ */
+enum nl80211_peer_measurement_peer_attrs {
+ __NL80211_PMSR_PEER_ATTR_INVALID,
+
+ NL80211_PMSR_PEER_ATTR_ADDR,
+ NL80211_PMSR_PEER_ATTR_CHAN,
+ NL80211_PMSR_PEER_ATTR_REQ,
+ NL80211_PMSR_PEER_ATTR_RESP,
+
+ /* keep last */
+ NUM_NL80211_PMSR_PEER_ATTRS,
+ NL80211_PMSR_PEER_ATTR_MAX = NUM_NL80211_PMSR_PEER_ATTRS - 1,
+};
+
+/**
+ * enum nl80211_peer_measurement_attrs - peer measurement attributes
+ * @__NL80211_PMSR_ATTR_INVALID: invalid
+ *
+ * @NL80211_PMSR_ATTR_MAX_PEERS: u32 attribute used for capability
+ * advertisement only, indicates the maximum number of peers
+ * measurements can be done with in a single request
+ * @NL80211_PMSR_ATTR_REPORT_AP_TSF: flag attribute in capability
+ * indicating that the connected AP's TSF can be reported in
+ * measurement results
+ * @NL80211_PMSR_ATTR_RANDOMIZE_MAC_ADDR: flag attribute in capability
+ * indicating that MAC address randomization is supported.
+ * @NL80211_PMSR_ATTR_TYPE_CAPA: capabilities reported by the device,
+ * this contains a nesting indexed by measurement type, and
+ * type-specific capabilities inside, which are from the enums
+ * named nl80211_peer_measurement_<type>_capa.
+ * @NL80211_PMSR_ATTR_PEERS: nested attribute, the nesting index is
+ * meaningless, just a list of peers to measure with, with the
+ * sub-attributes taken from
+ * &enum nl80211_peer_measurement_peer_attrs.
+ *
+ * @NUM_NL80211_PMSR_ATTR: internal
+ * @NL80211_PMSR_ATTR_MAX: highest attribute number
+ */
+enum nl80211_peer_measurement_attrs {
+ __NL80211_PMSR_ATTR_INVALID,
+
+ NL80211_PMSR_ATTR_MAX_PEERS,
+ NL80211_PMSR_ATTR_REPORT_AP_TSF,
+ NL80211_PMSR_ATTR_RANDOMIZE_MAC_ADDR,
+ NL80211_PMSR_ATTR_TYPE_CAPA,
+ NL80211_PMSR_ATTR_PEERS,
+
+ /* keep last */
+ NUM_NL80211_PMSR_ATTR,
+ NL80211_PMSR_ATTR_MAX = NUM_NL80211_PMSR_ATTR - 1
+};
+
+/**
+ * enum nl80211_peer_measurement_ftm_capa - FTM capabilities
+ * @__NL80211_PMSR_FTM_CAPA_ATTR_INVALID: invalid
+ *
+ * @NL80211_PMSR_FTM_CAPA_ATTR_ASAP: flag attribute indicating ASAP mode
+ * is supported
+ * @NL80211_PMSR_FTM_CAPA_ATTR_NON_ASAP: flag attribute indicating non-ASAP
+ * mode is supported
+ * @NL80211_PMSR_FTM_CAPA_ATTR_REQ_LCI: flag attribute indicating if LCI
+ * data can be requested during the measurement
+ * @NL80211_PMSR_FTM_CAPA_ATTR_REQ_CIVICLOC: flag attribute indicating if civic
+ * location data can be requested during the measurement
+ * @NL80211_PMSR_FTM_CAPA_ATTR_PREAMBLES: u32 bitmap attribute of bits
+ * from &enum nl80211_preamble.
+ * @NL80211_PMSR_FTM_CAPA_ATTR_BANDWIDTHS: bitmap of values from
+ * &enum nl80211_chan_width indicating the supported channel
+ * bandwidths for FTM. Note that a higher channel bandwidth may be
+ * configured to allow for other measurements types with different
+ * bandwidth requirement in the same measurement.
+ * @NL80211_PMSR_FTM_CAPA_ATTR_MAX_BURSTS_EXPONENT: u32 attribute indicating
+ * the maximum bursts exponent that can be used (if not present anything
+ * is valid)
+ * @NL80211_PMSR_FTM_CAPA_ATTR_MAX_FTMS_PER_BURST: u32 attribute indicating
+ * the maximum FTMs per burst (if not present anything is valid)
+ *
+ * @NUM_NL80211_PMSR_FTM_CAPA_ATTR: internal
+ * @NL80211_PMSR_FTM_CAPA_ATTR_MAX: highest attribute number
+ */
+enum nl80211_peer_measurement_ftm_capa {
+ __NL80211_PMSR_FTM_CAPA_ATTR_INVALID,
+
+ NL80211_PMSR_FTM_CAPA_ATTR_ASAP,
+ NL80211_PMSR_FTM_CAPA_ATTR_NON_ASAP,
+ NL80211_PMSR_FTM_CAPA_ATTR_REQ_LCI,
+ NL80211_PMSR_FTM_CAPA_ATTR_REQ_CIVICLOC,
+ NL80211_PMSR_FTM_CAPA_ATTR_PREAMBLES,
+ NL80211_PMSR_FTM_CAPA_ATTR_BANDWIDTHS,
+ NL80211_PMSR_FTM_CAPA_ATTR_MAX_BURSTS_EXPONENT,
+ NL80211_PMSR_FTM_CAPA_ATTR_MAX_FTMS_PER_BURST,
+
+ /* keep last */
+ NUM_NL80211_PMSR_FTM_CAPA_ATTR,
+ NL80211_PMSR_FTM_CAPA_ATTR_MAX = NUM_NL80211_PMSR_FTM_CAPA_ATTR - 1
+};
+
+/**
+ * enum nl80211_peer_measurement_ftm_req - FTM request attributes
+ * @__NL80211_PMSR_FTM_REQ_ATTR_INVALID: invalid
+ *
+ * @NL80211_PMSR_FTM_REQ_ATTR_ASAP: ASAP mode requested (flag)
+ * @NL80211_PMSR_FTM_REQ_ATTR_PREAMBLE: preamble type (see
+ * &enum nl80211_preamble), optional for DMG (u32)
+ * @NL80211_PMSR_FTM_REQ_ATTR_NUM_BURSTS_EXP: number of bursts exponent as in
+ * 802.11-2016 9.4.2.168 "Fine Timing Measurement Parameters element"
+ * (u8, 0-15, optional with default 15 i.e. "no preference")
+ * @NL80211_PMSR_FTM_REQ_ATTR_BURST_PERIOD: interval between bursts in units
+ * of 100ms (u16, optional with default 0)
+ * @NL80211_PMSR_FTM_REQ_ATTR_BURST_DURATION: burst duration, as in 802.11-2016
+ * Table 9-257 "Burst Duration field encoding" (u8, 0-15, optional with
+ * default 15 i.e. "no preference")
+ * @NL80211_PMSR_FTM_REQ_ATTR_FTMS_PER_BURST: number of successful FTM frames
+ * requested per burst
+ * (u8, 0-31, optional with default 0 i.e. "no preference")
+ * @NL80211_PMSR_FTM_REQ_ATTR_NUM_FTMR_RETRIES: number of FTMR frame retries
+ * (u8, default 3)
+ * @NL80211_PMSR_FTM_REQ_ATTR_REQUEST_LCI: request LCI data (flag)
+ * @NL80211_PMSR_FTM_REQ_ATTR_REQUEST_CIVICLOC: request civic location data
+ * (flag)
+ *
+ * @NUM_NL80211_PMSR_FTM_REQ_ATTR: internal
+ * @NL80211_PMSR_FTM_REQ_ATTR_MAX: highest attribute number
+ */
+enum nl80211_peer_measurement_ftm_req {
+ __NL80211_PMSR_FTM_REQ_ATTR_INVALID,
+
+ NL80211_PMSR_FTM_REQ_ATTR_ASAP,
+ NL80211_PMSR_FTM_REQ_ATTR_PREAMBLE,
+ NL80211_PMSR_FTM_REQ_ATTR_NUM_BURSTS_EXP,
+ NL80211_PMSR_FTM_REQ_ATTR_BURST_PERIOD,
+ NL80211_PMSR_FTM_REQ_ATTR_BURST_DURATION,
+ NL80211_PMSR_FTM_REQ_ATTR_FTMS_PER_BURST,
+ NL80211_PMSR_FTM_REQ_ATTR_NUM_FTMR_RETRIES,
+ NL80211_PMSR_FTM_REQ_ATTR_REQUEST_LCI,
+ NL80211_PMSR_FTM_REQ_ATTR_REQUEST_CIVICLOC,
+
+ /* keep last */
+ NUM_NL80211_PMSR_FTM_REQ_ATTR,
+ NL80211_PMSR_FTM_REQ_ATTR_MAX = NUM_NL80211_PMSR_FTM_REQ_ATTR - 1
+};
+
+/**
+ * enum nl80211_peer_measurement_ftm_failure_reasons - FTM failure reasons
+ * @NL80211_PMSR_FTM_FAILURE_UNSPECIFIED: unspecified failure, not used
+ * @NL80211_PMSR_FTM_FAILURE_NO_RESPONSE: no response from the FTM responder
+ * @NL80211_PMSR_FTM_FAILURE_REJECTED: FTM responder rejected measurement
+ * @NL80211_PMSR_FTM_FAILURE_WRONG_CHANNEL: we already know the peer is
+ * on a different channel, so can't measure (if we didn't know, we'd
+ * try and get no response)
+ * @NL80211_PMSR_FTM_FAILURE_PEER_NOT_CAPABLE: peer can't actually do FTM
+ * @NL80211_PMSR_FTM_FAILURE_INVALID_TIMESTAMP: invalid T1/T4 timestamps
+ * received
+ * @NL80211_PMSR_FTM_FAILURE_PEER_BUSY: peer reports busy, you may retry
+ * later (see %NL80211_PMSR_FTM_RESP_ATTR_BUSY_RETRY_TIME)
+ * @NL80211_PMSR_FTM_FAILURE_BAD_CHANGED_PARAMS: parameters were changed
+ * by the peer and are no longer supported
+ */
+enum nl80211_peer_measurement_ftm_failure_reasons {
+ NL80211_PMSR_FTM_FAILURE_UNSPECIFIED,
+ NL80211_PMSR_FTM_FAILURE_NO_RESPONSE,
+ NL80211_PMSR_FTM_FAILURE_REJECTED,
+ NL80211_PMSR_FTM_FAILURE_WRONG_CHANNEL,
+ NL80211_PMSR_FTM_FAILURE_PEER_NOT_CAPABLE,
+ NL80211_PMSR_FTM_FAILURE_INVALID_TIMESTAMP,
+ NL80211_PMSR_FTM_FAILURE_PEER_BUSY,
+ NL80211_PMSR_FTM_FAILURE_BAD_CHANGED_PARAMS,
+};
+
+/**
+ * enum nl80211_peer_measurement_ftm_resp - FTM response attributes
+ * @__NL80211_PMSR_FTM_RESP_ATTR_INVALID: invalid
+ *
+ * @NL80211_PMSR_FTM_RESP_ATTR_FAIL_REASON: FTM-specific failure reason
+ * (u32, optional)
+ * @NL80211_PMSR_FTM_RESP_ATTR_BURST_INDEX: optional, if bursts are reported
+ * as separate results then it will be the burst index 0...(N-1) and
+ * the top level will indicate partial results (u32)
+ * @NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_ATTEMPTS: number of FTM Request frames
+ * transmitted (u32, optional)
+ * @NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_SUCCESSES: number of FTM Request frames
+ * that were acknowleged (u32, optional)
+ * @NL80211_PMSR_FTM_RESP_ATTR_BUSY_RETRY_TIME: retry time received from the
+ * busy peer (u32, seconds)
+ * @NL80211_PMSR_FTM_RESP_ATTR_NUM_BURSTS_EXP: actual number of bursts exponent
+ * used by the responder (similar to request, u8)
+ * @NL80211_PMSR_FTM_RESP_ATTR_BURST_DURATION: actual burst duration used by
+ * the responder (similar to request, u8)
+ * @NL80211_PMSR_FTM_RESP_ATTR_FTMS_PER_BURST: actual FTMs per burst used
+ * by the responder (similar to request, u8)
+ * @NL80211_PMSR_FTM_RESP_ATTR_RSSI_AVG: average RSSI across all FTM action
+ * frames (optional, s32, 1/2 dBm)
+ * @NL80211_PMSR_FTM_RESP_ATTR_RSSI_SPREAD: RSSI spread across all FTM action
+ * frames (optional, s32, 1/2 dBm)
+ * @NL80211_PMSR_FTM_RESP_ATTR_TX_RATE: bitrate we used for the response to the
+ * FTM action frame (optional, nested, using &enum nl80211_rate_info
+ * attributes)
+ * @NL80211_PMSR_FTM_RESP_ATTR_RX_RATE: bitrate the responder used for the FTM
+ * action frame (optional, nested, using &enum nl80211_rate_info attrs)
+ * @NL80211_PMSR_FTM_RESP_ATTR_RTT_AVG: average RTT (s64, picoseconds, optional
+ * but one of RTT/DIST must be present)
+ * @NL80211_PMSR_FTM_RESP_ATTR_RTT_VARIANCE: RTT variance (u64, ps^2, note that
+ * standard deviation is the square root of variance, optional)
+ * @NL80211_PMSR_FTM_RESP_ATTR_RTT_SPREAD: RTT spread (u64, picoseconds,
+ * optional)
+ * @NL80211_PMSR_FTM_RESP_ATTR_DIST_AVG: average distance (s64, mm, optional
+ * but one of RTT/DIST must be present)
+ * @NL80211_PMSR_FTM_RESP_ATTR_DIST_VARIANCE: distance variance (u64, mm^2, note
+ * that standard deviation is the square root of variance, optional)
+ * @NL80211_PMSR_FTM_RESP_ATTR_DIST_SPREAD: distance spread (u64, mm, optional)
+ * @NL80211_PMSR_FTM_RESP_ATTR_LCI: LCI data from peer (binary, optional);
+ * this is the contents of the Measurement Report Element (802.11-2016
+ * 9.4.2.22.1) starting with the Measurement Token, with Measurement
+ * Type 8.
+ * @NL80211_PMSR_FTM_RESP_ATTR_CIVICLOC: civic location data from peer
+ * (binary, optional);
+ * this is the contents of the Measurement Report Element (802.11-2016
+ * 9.4.2.22.1) starting with the Measurement Token, with Measurement
+ * Type 11.
+ * @NL80211_PMSR_FTM_RESP_ATTR_PAD: ignore, for u64/s64 padding only
+ *
+ * @NUM_NL80211_PMSR_FTM_RESP_ATTR: internal
+ * @NL80211_PMSR_FTM_RESP_ATTR_MAX: highest attribute number
+ */
+enum nl80211_peer_measurement_ftm_resp {
+ __NL80211_PMSR_FTM_RESP_ATTR_INVALID,
+
+ NL80211_PMSR_FTM_RESP_ATTR_FAIL_REASON,
+ NL80211_PMSR_FTM_RESP_ATTR_BURST_INDEX,
+ NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_ATTEMPTS,
+ NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_SUCCESSES,
+ NL80211_PMSR_FTM_RESP_ATTR_BUSY_RETRY_TIME,
+ NL80211_PMSR_FTM_RESP_ATTR_NUM_BURSTS_EXP,
+ NL80211_PMSR_FTM_RESP_ATTR_BURST_DURATION,
+ NL80211_PMSR_FTM_RESP_ATTR_FTMS_PER_BURST,
+ NL80211_PMSR_FTM_RESP_ATTR_RSSI_AVG,
+ NL80211_PMSR_FTM_RESP_ATTR_RSSI_SPREAD,
+ NL80211_PMSR_FTM_RESP_ATTR_TX_RATE,
+ NL80211_PMSR_FTM_RESP_ATTR_RX_RATE,
+ NL80211_PMSR_FTM_RESP_ATTR_RTT_AVG,
+ NL80211_PMSR_FTM_RESP_ATTR_RTT_VARIANCE,
+ NL80211_PMSR_FTM_RESP_ATTR_RTT_SPREAD,
+ NL80211_PMSR_FTM_RESP_ATTR_DIST_AVG,
+ NL80211_PMSR_FTM_RESP_ATTR_DIST_VARIANCE,
+ NL80211_PMSR_FTM_RESP_ATTR_DIST_SPREAD,
+ NL80211_PMSR_FTM_RESP_ATTR_LCI,
+ NL80211_PMSR_FTM_RESP_ATTR_CIVICLOC,
+ NL80211_PMSR_FTM_RESP_ATTR_PAD,
+
+ /* keep last */
+ NUM_NL80211_PMSR_FTM_RESP_ATTR,
+ NL80211_PMSR_FTM_RESP_ATTR_MAX = NUM_NL80211_PMSR_FTM_RESP_ATTR - 1
+};
+
#endif /* __LINUX_NL80211_H */
projects / thirdparty / iw.git / blobdiff