Merge git://git.denx.de/u-boot-fdt

[people/ms/u-boot.git] / include / configs / vme8349.h

/*
 * esd vme8349 U-Boot configuration file
 * Copyright (c) 2008, 2009 esd gmbh Hannover Germany
 *
 * (C) Copyright 2006-2010
 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 *
 * reinhard.arlt@esd-electronics.de
 * Based on the MPC8349EMDS config.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/*
 * vme8349 board configuration file.
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * Top level Makefile configuration choices
 */
#ifdef CONFIG_CADDY2
#define VME_CADDY2
#endif

/*
 * High Level Configuration Options
 */
#define CONFIG_E300		1	/* E300 Family */
#define CONFIG_MPC834x		1	/* MPC834x family */
#define CONFIG_MPC8349		1	/* MPC8349 specific */
#define CONFIG_VME8349		1	/* ESD VME8349 board specific */

#define	CONFIG_SYS_TEXT_BASE	0xFFF00000

#define CONFIG_MISC_INIT_R

#define CONFIG_PCI
/* Don't enable PCI2 on vme834x - it doesn't exist physically. */
#undef CONFIG_MPC83XX_PCI2		/* support for 2nd PCI controller */

#define CONFIG_PCI_66M
#ifdef CONFIG_PCI_66M
#define CONFIG_83XX_CLKIN	66000000	/* in Hz */
#else
#define CONFIG_83XX_CLKIN	33000000	/* in Hz */
#endif

#ifndef CONFIG_SYS_CLK_FREQ
#ifdef CONFIG_PCI_66M
#define CONFIG_SYS_CLK_FREQ	66000000
#define HRCWL_CSB_TO_CLKIN	HRCWL_CSB_TO_CLKIN_4X1
#else
#define CONFIG_SYS_CLK_FREQ	33000000
#define HRCWL_CSB_TO_CLKIN	HRCWL_CSB_TO_CLKIN_8X1
#endif
#endif

#define CONFIG_SYS_IMMR		0xE0000000

#undef CONFIG_SYS_DRAM_TEST			/* memory test, takes time */
#define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest region */
#define CONFIG_SYS_MEMTEST_END		0x00100000

/*
 * DDR Setup
 */
#define CONFIG_DDR_ECC			/* only for ECC DDR module */
#define CONFIG_DDR_ECC_CMD		/* use DDR ECC user commands */
#define CONFIG_SPD_EEPROM
#define SPD_EEPROM_ADDRESS		0x54
#define CONFIG_SYS_READ_SPD		vme8349_read_spd
#define CONFIG_SYS_83XX_DDR_USES_CS0	/* esd; Fsl board uses CS2/CS3 */

/*
 * 32-bit data path mode.
 *
 * Please note that using this mode for devices with the real density of 64-bit
 * effectively reduces the amount of available memory due to the effect of
 * wrapping around while translating address to row/columns, for example in the
 * 256MB module the upper 128MB get aliased with contents of the lower
 * 128MB); normally this define should be used for devices with real 32-bit
 * data path.
 */
#undef CONFIG_DDR_32BIT

#define CONFIG_SYS_DDR_BASE		0x00000000	/* DDR is sys memory*/
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN \
					| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
#define CONFIG_DDR_2T_TIMING
#define CONFIG_SYS_DDRCDR		(DDRCDR_DHC_EN \
					| DDRCDR_ODT \
					| DDRCDR_Q_DRN)
					/* 0x80080001 */

/*
 * FLASH on the Local Bus
 */
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER			        /* use the CFI driver */
#ifdef VME_CADDY2
#define CONFIG_SYS_FLASH_BASE		0xffc00000	/* start of FLASH   */
#define CONFIG_SYS_FLASH_SIZE		4		/* flash size in MB */
#define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE | \
					 BR_PS_16 |	/*  16bit */ \
					 BR_MS_GPCM |	/*  MSEL = GPCM */ \
					 BR_V)		/* valid */

#define CONFIG_SYS_OR0_PRELIM		(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
					| OR_GPCM_XAM \
					| OR_GPCM_CSNT \
					| OR_GPCM_ACS_DIV2 \
					| OR_GPCM_XACS \
					| OR_GPCM_SCY_15 \
					| OR_GPCM_TRLX_SET \
					| OR_GPCM_EHTR_SET \
					| OR_GPCM_EAD)
					/* 0xffc06ff7 */
#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_4MB)
#else
#define CONFIG_SYS_FLASH_BASE		0xf8000000	/* start of FLASH   */
#define CONFIG_SYS_FLASH_SIZE		128		/* flash size in MB */
#define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE | \
					 BR_PS_16 |	/*  16bit */ \
					 BR_MS_GPCM |	/*  MSEL = GPCM */ \
					 BR_V)		/* valid */

#define CONFIG_SYS_OR0_PRELIM		(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
					| OR_GPCM_XAM \
					| OR_GPCM_CSNT \
					| OR_GPCM_ACS_DIV2 \
					| OR_GPCM_XACS \
					| OR_GPCM_SCY_15 \
					| OR_GPCM_TRLX_SET \
					| OR_GPCM_EHTR_SET \
					| OR_GPCM_EAD)
					/* 0xf8006ff7 */
#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_128MB)
#endif
/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */

#define CONFIG_SYS_WINDOW1_BASE		0xf0000000
#define CONFIG_SYS_BR1_PRELIM		(CONFIG_SYS_WINDOW1_BASE \
					| BR_PS_32 \
					| BR_MS_GPCM \
					| BR_V)
					/* 0xF0001801 */
#define CONFIG_SYS_OR1_PRELIM		(OR_AM_256KB \
					| OR_GPCM_SETA)
					/* 0xfffc0208 */
#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_WINDOW1_BASE
#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_256KB)

#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device*/

#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase TO (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write TO (ms) */

#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */

#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#else
#undef CONFIG_SYS_RAMBOOT
#endif

#define CONFIG_SYS_INIT_RAM_LOCK	1
#define CONFIG_SYS_INIT_RAM_ADDR	0xF7000000	/* Initial RAM addr */
#define CONFIG_SYS_INIT_RAM_SIZE		0x1000		/* size */

#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
					 GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB */
#define CONFIG_SYS_MALLOC_LEN		(256 * 1024)	/* Malloc size */

/*
 * Local Bus LCRR and LBCR regs
 *    LCRR:  no DLL bypass, Clock divider is 4
 * External Local Bus rate is
 *    CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
 */
#define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR	0x00000000

#undef CONFIG_SYS_LB_SDRAM	/* if board has SDRAM on local bus */

/*
 * Serial Port
 */
#define CONFIG_CONS_INDEX	1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

#define CONFIG_SYS_BAUDRATE_TABLE  \
		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

#define CONFIG_SYS_NS16550_COM1		(CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2		(CONFIG_SYS_IMMR + 0x4600)

#define CONFIG_CMDLINE_EDITING		/* add command line history	*/
#define CONFIG_AUTO_COMPLETE		/* add autocompletion support */
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER

/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_OF_STDOUT_VIA_ALIAS

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED	400000
#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
#define CONFIG_SYS_FSL_I2C2_SPEED	400000
#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */

#define CONFIG_SYS_I2C_8574_ADDR2       0x20    /* I2C1, PCF8574 */

/* TSEC */
#define CONFIG_SYS_TSEC1_OFFSET	0x24000
#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
#define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)

/*
 * General PCI
 * Addresses are mapped 1-1.
 */
#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
#define CONFIG_SYS_PCI1_IO_BASE		0x00000000
#define CONFIG_SYS_PCI1_IO_PHYS		0xE2000000
#define CONFIG_SYS_PCI1_IO_SIZE		0x00100000	/* 1M */

#define CONFIG_SYS_PCI2_MEM_BASE	0xA0000000
#define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
#define CONFIG_SYS_PCI2_MEM_SIZE	0x10000000	/* 256M */
#define CONFIG_SYS_PCI2_MMIO_BASE	0xB0000000
#define CONFIG_SYS_PCI2_MMIO_PHYS	CONFIG_SYS_PCI2_MMIO_BASE
#define CONFIG_SYS_PCI2_MMIO_SIZE	0x10000000	/* 256M */
#define CONFIG_SYS_PCI2_IO_BASE		0x00000000
#define CONFIG_SYS_PCI2_IO_PHYS		0xE2100000
#define CONFIG_SYS_PCI2_IO_SIZE		0x00100000	/* 1M */

#if defined(CONFIG_PCI)

#define PCI_64BIT
#define PCI_ONE_PCI1
#if defined(PCI_64BIT)
#undef PCI_ALL_PCI1
#undef PCI_TWO_PCI1
#undef PCI_ONE_PCI1
#endif

#ifndef VME_CADDY2
#endif
#define CONFIG_PCI_PNP		/* do pci plug-and-play */

#undef CONFIG_EEPRO100
#undef CONFIG_TULIP

#if !defined(CONFIG_PCI_PNP)
	#define PCI_ENET0_IOADDR	0xFIXME
	#define PCI_ENET0_MEMADDR	0xFIXME
	#define PCI_IDSEL_NUMBER	0xFIXME
#endif

#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID	0x1957	/* Freescale */

#endif	/* CONFIG_PCI */

/*
 * TSEC configuration
 */
#ifdef VME_CADDY2
#define CONFIG_E1000
#else
#define CONFIG_TSEC_ENET		/* TSEC ethernet support */
#endif

#if defined(CONFIG_TSEC_ENET)

#define CONFIG_GMII			/* MII PHY management */
#define CONFIG_TSEC1
#define CONFIG_TSEC1_NAME	"TSEC0"
#define CONFIG_TSEC2
#define CONFIG_TSEC2_NAME	"TSEC1"
#define CONFIG_PHY_M88E1111
#define TSEC1_PHY_ADDR		0x08
#define TSEC2_PHY_ADDR		0x10
#define TSEC1_PHYIDX		0
#define TSEC2_PHYIDX		0
#define TSEC1_FLAGS		TSEC_GIGABIT
#define TSEC2_FLAGS		TSEC_GIGABIT

/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME		"TSEC0"

#endif	/* CONFIG_TSEC_ENET */

/*
 * Environment
 */
#ifndef CONFIG_SYS_RAMBOOT
	#define CONFIG_ENV_IS_IN_FLASH
	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0xc0000)
	#define CONFIG_ENV_SECT_SIZE	0x20000	/* 128K(one sector) for env */
	#define CONFIG_ENV_SIZE		0x2000

/* Address and size of Redundant Environment Sector	*/
#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)

#else
	#define CONFIG_SYS_NO_FLASH		/* Flash is not usable now */
	#define CONFIG_ENV_IS_NOWHERE		/* Store ENV in memory only */
	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
	#define CONFIG_ENV_SIZE		0x2000
#endif

#define CONFIG_LOADS_ECHO		/* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME

/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_DATE
#define CONFIG_SYS_RTC_BUS_NUM  0x01
#define CONFIG_SYS_I2C_RTC_ADDR	0x32
#define CONFIG_RTC_RX8025
#define CONFIG_CMD_TSI148

#if defined(CONFIG_PCI)
    #define CONFIG_CMD_PCI
#endif

#if defined(CONFIG_SYS_RAMBOOT)
    #undef CONFIG_CMD_ENV
    #undef CONFIG_CMD_LOADS
#endif

#define CONFIG_CMD_ELF
/* Pass Ethernet MAC to VxWorks */
#define CONFIG_SYS_VXWORKS_MAC_PTR	0x000043f0

#undef CONFIG_WATCHDOG			/* watchdog disabled */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */

#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE	1024	/* Console I/O Buffer Size */
#else
	#define CONFIG_SYS_CBSIZE	256	/* Console I/O Buffer Size */
#endif

#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS	16		/* max num of command args */
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE /* Boot Argument Buf Size */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 256 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ	(256 << 20)	/* Init Memory map for Linux*/

#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */

#define CONFIG_SYS_HRCW_LOW (\
	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
	HRCWL_DDR_TO_SCB_CLK_1X1 |\
	HRCWL_CSB_TO_CLKIN |\
	HRCWL_VCO_1X2 |\
	HRCWL_CORE_TO_CSB_2X1)

#if defined(PCI_64BIT)
#define CONFIG_SYS_HRCW_HIGH (\
	HRCWH_PCI_HOST |\
	HRCWH_64_BIT_PCI |\
	HRCWH_PCI1_ARBITER_ENABLE |\
	HRCWH_PCI2_ARBITER_DISABLE |\
	HRCWH_CORE_ENABLE |\
	HRCWH_FROM_0X00000100 |\
	HRCWH_BOOTSEQ_DISABLE |\
	HRCWH_SW_WATCHDOG_DISABLE |\
	HRCWH_ROM_LOC_LOCAL_16BIT |\
	HRCWH_TSEC1M_IN_GMII |\
	HRCWH_TSEC2M_IN_GMII)
#else
#define CONFIG_SYS_HRCW_HIGH (\
	HRCWH_PCI_HOST |\
	HRCWH_32_BIT_PCI |\
	HRCWH_PCI1_ARBITER_ENABLE |\
	HRCWH_PCI2_ARBITER_ENABLE |\
	HRCWH_CORE_ENABLE |\
	HRCWH_FROM_0X00000100 |\
	HRCWH_BOOTSEQ_DISABLE |\
	HRCWH_SW_WATCHDOG_DISABLE |\
	HRCWH_ROM_LOC_LOCAL_16BIT |\
	HRCWH_TSEC1M_IN_GMII |\
	HRCWH_TSEC2M_IN_GMII)
#endif

/* System IO Config */
#define CONFIG_SYS_SICRH 0
#define CONFIG_SYS_SICRL SICRL_LDP_A

#define CONFIG_SYS_HID0_INIT	0x000000000
#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
				 HID0_ENABLE_INSTRUCTION_CACHE)

#define CONFIG_SYS_HID2		HID2_HBE

#define CONFIG_SYS_GPIO1_PRELIM
#define CONFIG_SYS_GPIO1_DIR	0x00100000
#define CONFIG_SYS_GPIO1_DAT	0x00100000

#define CONFIG_SYS_GPIO2_PRELIM
#define CONFIG_SYS_GPIO2_DIR	0x78900000
#define CONFIG_SYS_GPIO2_DAT	0x70100000

#define CONFIG_HIGH_BATS		/* High BATs supported */

/* DDR @ 0x00000000 */
#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
				 BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
				 BATU_VS | BATU_VP)

/* PCI @ 0x80000000 */
#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW | \
				 BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | \
				 BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_RW | \
				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | \
				 BATU_VS | BATU_VP)
#else
#define CONFIG_SYS_IBAT1L	(0)
#define CONFIG_SYS_IBAT1U	(0)
#define CONFIG_SYS_IBAT2L	(0)
#define CONFIG_SYS_IBAT2U	(0)
#endif

#ifdef CONFIG_MPC83XX_PCI2
#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_PCI2_MEM_BASE | BATL_PP_RW | \
				 BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_PCI2_MEM_BASE | BATU_BL_256M | \
				 BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCI2_MMIO_BASE | BATL_PP_RW | \
				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_PCI2_MMIO_BASE | BATU_BL_256M | \
				 BATU_VS | BATU_VP)
#else
#define CONFIG_SYS_IBAT3L	(0)
#define CONFIG_SYS_IBAT3U	(0)
#define CONFIG_SYS_IBAT4L	(0)
#define CONFIG_SYS_IBAT4U	(0)
#endif

/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_IMMR | BATL_PP_RW | \
				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_IMMR | BATU_BL_256M | \
				 BATU_VS | BATU_VP)

#define CONFIG_SYS_IBAT6L	(0xF0000000 | BATL_PP_RW | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT6U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)

#if (CONFIG_SYS_DDR_SIZE == 512)
#define CONFIG_SYS_IBAT7L	(CONFIG_SYS_SDRAM_BASE+0x10000000 | \
				 BATL_PP_RW | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT7U	(CONFIG_SYS_SDRAM_BASE+0x10000000 | \
				 BATU_BL_256M | BATU_VS | BATU_VP)
#else
#define CONFIG_SYS_IBAT7L	(0)
#define CONFIG_SYS_IBAT7U	(0)
#endif

#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
#endif

/*
 * Environment Configuration
 */
#define CONFIG_ENV_OVERWRITE

#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#endif

#define CONFIG_HOSTNAME		VME8349
#define CONFIG_ROOTPATH		"/tftpboot/rootfs"
#define CONFIG_BOOTFILE		"uImage"

#define CONFIG_LOADADDR		800000	/* def location for tftp and bootm */

#define CONFIG_BOOTDELAY	6	/* -1 disables auto-boot */
#undef  CONFIG_BOOTARGS			/* boot command will set bootargs */

#define CONFIG_BAUDRATE	 9600

#define	CONFIG_EXTRA_ENV_SETTINGS					\
	"netdev=eth0\0"							\
	"hostname=vme8349\0"						\
	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
		"nfsroot=${serverip}:${rootpath}\0"			\
	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
	"addip=setenv bootargs ${bootargs} "				\
		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
		":${hostname}:${netdev}:off panic=1\0"			\
	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
	"flash_nfs=run nfsargs addip addtty;"				\
		"bootm ${kernel_addr}\0"				\
	"flash_self=run ramargs addip addtty;"				\
		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"	\
		"bootm\0"						\
	"load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0"		\
	"update=protect off fff00000 fff3ffff; "			\
		"era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
	"upd=run load update\0"						\
	"fdtaddr=780000\0"						\
	"fdtfile=vme8349.dtb\0"						\
	""

#define CONFIG_NFSBOOTCOMMAND						\
	"setenv bootargs root=/dev/nfs rw "				\
		"nfsroot=$serverip:$rootpath "				\
		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
							"$netdev:off "	\
		"console=$consoledev,$baudrate $othbootargs;"		\
	"tftp $loadaddr $bootfile;"					\
	"tftp $fdtaddr $fdtfile;"					\
	"bootm $loadaddr - $fdtaddr"

#define CONFIG_RAMBOOTCOMMAND						\
	"setenv bootargs root=/dev/ram rw "				\
		"console=$consoledev,$baudrate $othbootargs;"		\
	"tftp $ramdiskaddr $ramdiskfile;"				\
	"tftp $loadaddr $bootfile;"					\
	"tftp $fdtaddr $fdtfile;"					\
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_BOOTCOMMAND	"run flash_self"

#ifndef __ASSEMBLY__
int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen,
		     unsigned char *buffer, int len);
#endif

#endif	/* __CONFIG_H */