# as the long options legal on the command line. See
# "/usr/sbin/dnsmasq --help" or "man 8 dnsmasq" for details.
+# Listen on this specific port instead of the standard DNS port
+# (53). Setting this to zero completely disables DNS function,
+# leaving only DHCP and/or TFTP.
+#port=5353
+
# The following two options make you a better netizen, since they
# tell dnsmasq to filter out queries which the public DNS cannot
# answer, and which load the servers (especially the root servers)
-# uneccessarily. If you have a dial-on-demand link they also stop
-# these requests from bringing up the link uneccessarily.
+# unnecessarily. If you have a dial-on-demand link they also stop
+# these requests from bringing up the link unnecessarily.
# Never forward plain names (without a dot or domain part)
-domain-needed
+#domain-needed
# Never forward addresses in the non-routed address spaces.
-bogus-priv
+#bogus-priv
+
+# Uncomment these to enable DNSSEC validation and caching:
+# (Requires dnsmasq to be built with DNSSEC option.)
+#conf-file=%%PREFIX%%/share/dnsmasq/trust-anchors.conf
+#dnssec
+# Replies which are not DNSSEC signed may be legitimate, because the domain
+# is unsigned, or may be forgeries. Setting this option tells dnsmasq to
+# check that an unsigned reply is OK, by finding a secure proof that a DS
+# record somewhere between the root and the domain does not exist.
+# The cost of setting this is that even queries in unsigned domains will need
+# one or more extra DNS queries to verify.
+#dnssec-check-unsigned
# Uncomment this to filter useless windows-originated DNS requests
# which can trigger dial-on-demand links needlessly.
# Note that (amongst other things) this blocks all SRV requests,
-# so don't use it if you use eg Kerberos.
+# so don't use it if you use eg Kerberos, SIP, XMMP or Google-talk.
# This option only affects forwarding, SRV records originating for
# dnsmasq (via srv-host= lines) are not suppressed by it.
#filterwin2k
# If you don't want dnsmasq to read /etc/resolv.conf or any other
# file, getting its servers from this file instead (see below), then
-# uncomment this
+# uncomment this.
#no-resolv
# If you don't want dnsmasq to poll /etc/resolv.conf or other resolv
# non-public domains.
#server=/localnet/192.168.0.1
+# Example of routing PTR queries to nameservers: this will send all
+# address->name queries for 192.168.3/24 to nameserver 10.1.2.3
+#server=/3.168.192.in-addr.arpa/10.1.2.3
+
# Add local-only domains here, queries in these domains are answered
# from /etc/hosts or DHCP only.
#local=/localnet/
# Add domains which you want to force to an IP address here.
-# The example below send any host in doubleclick.net to a local
-# webserver.
-#address=/doubleclick.net/127.0.0.1
+# The example below send any host in double-click.net to a local
+# web-server.
+#address=/double-click.net/127.0.0.1
+
+# --address (and --server) work with IPv6 addresses too.
+#address=/www.thekelleys.org.uk/fe80::20d:60ff:fe36:f83
+
+# Add the IPs of all queries to yahoo.com, google.com, and their
+# subdomains to the vpn and search ipsets:
+#ipset=/yahoo.com/google.com/vpn,search
+
+# You can control how dnsmasq talks to a server: this forces
+# queries to 10.1.2.3 to be routed via eth1
+# server=10.1.2.3@eth1
+
+# and this sets the source (ie local) address used to talk to
+# 10.1.2.3 to 192.168.1.1 port 55 (there must be a interface with that
+# IP on the machine, obviously).
+# server=10.1.2.3@192.168.1.1#55
# If you want dnsmasq to change uid and gid to something other
# than the default, edit the following lines.
#listen-address=
# If you want dnsmasq to provide only DNS service on an interface,
# configure it as shown above, and then use the following line to
-# disable DHCP on it.
+# disable DHCP and TFTP on it.
#no-dhcp-interface=
# On systems which support it, dnsmasq binds the wildcard address,
# 3) Provides the domain part for "expand-hosts"
#domain=thekelleys.org.uk
+# Set a different domain for a particular subnet
+#domain=wireless.thekelleys.org.uk,192.168.2.0/24
+
+# Same idea, but range rather then subnet
+#domain=reserved.thekelleys.org.uk,192.68.3.100,192.168.3.200
+
# Uncomment this to enable the integrated DHCP server, you need
# to supply the range of addresses available for lease and optionally
# a lease time. If you have more than one network, you will need to
# don't need to worry about this.
#dhcp-range=192.168.0.50,192.168.0.150,255.255.255.0,12h
-# This is an example of a DHCP range with a network-id, so that
+# This is an example of a DHCP range which sets a tag, so that
# some DHCP options may be set only for this network.
-#dhcp-range=red,192.168.0.50,192.168.0.150
+#dhcp-range=set:red,192.168.0.50,192.168.0.150
+
+# Use this DHCP range only when the tag "green" is set.
+#dhcp-range=tag:green,192.168.0.50,192.168.0.150,12h
+
+# Specify a subnet which can't be used for dynamic address allocation,
+# is available for hosts with matching --dhcp-host lines. Note that
+# dhcp-host declarations will be ignored unless there is a dhcp-range
+# of some type for the subnet in question.
+# In this case the netmask is implied (it comes from the network
+# configuration on the machine running dnsmasq) it is possible to give
+# an explicit netmask instead.
+#dhcp-range=192.168.0.0,static
+
+# Enable DHCPv6. Note that the prefix-length does not need to be specified
+# and defaults to 64 if missing/
+#dhcp-range=1234::2, 1234::500, 64, 12h
+
+# Do Router Advertisements, BUT NOT DHCP for this subnet.
+#dhcp-range=1234::, ra-only
+
+# Do Router Advertisements, BUT NOT DHCP for this subnet, also try and
+# add names to the DNS for the IPv6 address of SLAAC-configured dual-stack
+# hosts. Use the DHCPv4 lease to derive the name, network segment and
+# MAC address and assume that the host will also have an
+# IPv6 address calculated using the SLAAC alogrithm.
+#dhcp-range=1234::, ra-names
+
+# Do Router Advertisements, BUT NOT DHCP for this subnet.
+# Set the lifetime to 46 hours. (Note: minimum lifetime is 2 hours.)
+#dhcp-range=1234::, ra-only, 48h
+
+# Do DHCP and Router Advertisements for this subnet. Set the A bit in the RA
+# so that clients can use SLAAC addresses as well as DHCP ones.
+#dhcp-range=1234::2, 1234::500, slaac
+
+# Do Router Advertisements and stateless DHCP for this subnet. Clients will
+# not get addresses from DHCP, but they will get other configuration information.
+# They will use SLAAC for addresses.
+#dhcp-range=1234::, ra-stateless
+
+# Do stateless DHCP, SLAAC, and generate DNS names for SLAAC addresses
+# from DHCPv4 leases.
+#dhcp-range=1234::, ra-stateless, ra-names
+
+# Do router advertisements for all subnets where we're doing DHCPv6
+# Unless overriden by ra-stateless, ra-names, et al, the router
+# advertisements will have the M and O bits set, so that the clients
+# get addresses and configuration from DHCPv6, and the A bit reset, so the
+# clients don't use SLAAC addresses.
+#enable-ra
# Supply parameters for specified hosts using DHCP. There are lots
# of valid alternatives, so we will give examples of each. Note that
# IP addresses DO NOT have to be in the range given above, they just
# need to be on the same network. The order of the parameters in these
-# do not matter, it's permissble to give name,adddress and MAC in any order
+# do not matter, it's permissible to give name, address and MAC in any
+# order.
-# Always allocate the host with ethernet address 11:22:33:44:55:66
+# Always allocate the host with Ethernet address 11:22:33:44:55:66
# The IP address 192.168.0.60
#dhcp-host=11:22:33:44:55:66,192.168.0.60
# 11:22:33:44:55:66 to be "fred"
#dhcp-host=11:22:33:44:55:66,fred
-# Always give the host with ethernet address 11:22:33:44:55:66
+# Always give the host with Ethernet address 11:22:33:44:55:66
# the name fred and IP address 192.168.0.60 and lease time 45 minutes
#dhcp-host=11:22:33:44:55:66,fred,192.168.0.60,45m
-# Give the machine which says it's name is "bert" IP address
+# Give a host with Ethernet address 11:22:33:44:55:66 or
+# 12:34:56:78:90:12 the IP address 192.168.0.60. Dnsmasq will assume
+# that these two Ethernet interfaces will never be in use at the same
+# time, and give the IP address to the second, even if it is already
+# in use by the first. Useful for laptops with wired and wireless
+# addresses.
+#dhcp-host=11:22:33:44:55:66,12:34:56:78:90:12,192.168.0.60
+
+# Give the machine which says its name is "bert" IP address
# 192.168.0.70 and an infinite lease
#dhcp-host=bert,192.168.0.70,infinite
# the IP address 192.168.0.60
#dhcp-host=id:01:02:02:04,192.168.0.60
+# Always give the Infiniband interface with hardware address
+# 80:00:00:48:fe:80:00:00:00:00:00:00:f4:52:14:03:00:28:05:81 the
+# ip address 192.168.0.61. The client id is derived from the prefix
+# ff:00:00:00:00:00:02:00:00:02:c9:00 and the last 8 pairs of
+# hex digits of the hardware address.
+#dhcp-host=id:ff:00:00:00:00:00:02:00:00:02:c9:00:f4:52:14:03:00:28:05:81,192.168.0.61
+
# Always give the host with client identifier "marjorie"
# the IP address 192.168.0.60
#dhcp-host=id:marjorie,192.168.0.60
# it asks for a DHCP lease.
#dhcp-host=judge
-# Never offer DHCP service to a machine whose ethernet
+# Never offer DHCP service to a machine whose Ethernet
# address is 11:22:33:44:55:66
#dhcp-host=11:22:33:44:55:66,ignore
-# Ignore any client-id presented by the machine with ethernet
+# Ignore any client-id presented by the machine with Ethernet
# address 11:22:33:44:55:66. This is useful to prevent a machine
# being treated differently when running under different OS's or
# between PXE boot and OS boot.
#dhcp-host=11:22:33:44:55:66,id:*
# Send extra options which are tagged as "red" to
-# the machine with ethernet address 11:22:33:44:55:66
-#dhcp-host=11:22:33:44:55:66,net:red
+# the machine with Ethernet address 11:22:33:44:55:66
+#dhcp-host=11:22:33:44:55:66,set:red
# Send extra options which are tagged as "red" to
-# any machine with ethernet address starting 11:22:33:
-#dhcp-host=11:22:33:*:*:*,net:red
+# any machine with Ethernet address starting 11:22:33:
+#dhcp-host=11:22:33:*:*:*,set:red
+
+# Give a fixed IPv6 address and name to client with
+# DUID 00:01:00:01:16:d2:83:fc:92:d4:19:e2:d8:b2
+# Note the MAC addresses CANNOT be used to identify DHCPv6 clients.
+# Note also the they [] around the IPv6 address are obilgatory.
+#dhcp-host=id:00:01:00:01:16:d2:83:fc:92:d4:19:e2:d8:b2, fred, [1234::5]
+
+# Ignore any clients which are not specified in dhcp-host lines
+# or /etc/ethers. Equivalent to ISC "deny unknown-clients".
+# This relies on the special "known" tag which is set when
+# a host is matched.
+#dhcp-ignore=tag:!known
# Send extra options which are tagged as "red" to any machine whose
# DHCP vendorclass string includes the substring "Linux"
-#dhcp-vendorclass=red,Linux
+#dhcp-vendorclass=set:red,Linux
# Send extra options which are tagged as "red" to any machine one
# of whose DHCP userclass strings includes the substring "accounts"
-#dhcp-userclass=red,accounts
+#dhcp-userclass=set:red,accounts
+
+# Send extra options which are tagged as "red" to any machine whose
+# MAC address matches the pattern.
+#dhcp-mac=set:red,00:60:8C:*:*:*
# If this line is uncommented, dnsmasq will read /etc/ethers and act
# on the ethernet-address/IP pairs found there just as if they had
# Send options to hosts which ask for a DHCP lease.
# See RFC 2132 for details of available options.
+# Common options can be given to dnsmasq by name:
+# run "dnsmasq --help dhcp" to get a list.
# Note that all the common settings, such as netmask and
# broadcast address, DNS server and default route, are given
-# sane defaults by dnsmasq. You very likely will not need any
+# sane defaults by dnsmasq. You very likely will not need
# any dhcp-options. If you use Windows clients and Samba, there
# are some options which are recommended, they are detailed at the
# end of this section.
-# For reference, the common options are:
-# subnet mask - 1
-# default router - 3
-# DNS server - 6
-# broadcast address - 28
+
+# Override the default route supplied by dnsmasq, which assumes the
+# router is the same machine as the one running dnsmasq.
+#dhcp-option=3,1.2.3.4
+
+# Do the same thing, but using the option name
+#dhcp-option=option:router,1.2.3.4
+
+# Override the default route supplied by dnsmasq and send no default
+# route at all. Note that this only works for the options sent by
+# default (1, 3, 6, 12, 28) the same line will send a zero-length option
+# for all other option numbers.
+#dhcp-option=3
# Set the NTP time server addresses to 192.168.0.4 and 10.10.0.5
-#dhcp-option=42,192.168.0.4,10.10.0.5
+#dhcp-option=option:ntp-server,192.168.0.4,10.10.0.5
+
+# Send DHCPv6 option. Note [] around IPv6 addresses.
+#dhcp-option=option6:dns-server,[1234::77],[1234::88]
+
+# Send DHCPv6 option for namservers as the machine running
+# dnsmasq and another.
+#dhcp-option=option6:dns-server,[::],[1234::88]
+
+# Ask client to poll for option changes every six hours. (RFC4242)
+#dhcp-option=option6:information-refresh-time,6h
+
+# Set option 58 client renewal time (T1). Defaults to half of the
+# lease time if not specified. (RFC2132)
+#dhcp-option=option:T1:1m
+
+# Set option 59 rebinding time (T2). Defaults to 7/8 of the
+# lease time if not specified. (RFC2132)
+#dhcp-option=option:T2:2m
# Set the NTP time server address to be the same machine as
# is running dnsmasq
# Specify an option which will only be sent to the "red" network
# (see dhcp-range for the declaration of the "red" network)
-#dhcp-option=red,42,192.168.1.1
+# Note that the tag: part must precede the option: part.
+#dhcp-option = tag:red, option:ntp-server, 192.168.1.1
# The following DHCP options set up dnsmasq in the same way as is specified
# for the ISC dhcpcd in
# http://www.samba.org/samba/ftp/docs/textdocs/DHCP-Server-Configuration.txt
# adapted for a typical dnsmasq installation where the host running
# dnsmasq is also the host running samba.
-# you may want to uncomment them if you use Windows clients and Samba.
+# you may want to uncomment some or all of them if you use
+# Windows clients and Samba.
#dhcp-option=19,0 # option ip-forwarding off
#dhcp-option=44,0.0.0.0 # set netbios-over-TCP/IP nameserver(s) aka WINS server(s)
#dhcp-option=45,0.0.0.0 # netbios datagram distribution server
#dhcp-option=46,8 # netbios node type
-#dhcp-option=47 # empty netbios scope.
+
+# Send an empty WPAD option. This may be REQUIRED to get windows 7 to behave.
+#dhcp-option=252,"\n"
# Send RFC-3397 DNS domain search DHCP option. WARNING: Your DHCP client
# probably doesn't support this......
-#dhcp-option=119,eng.apple.com,marketing.apple.com
+#dhcp-option=option:domain-search,eng.apple.com,marketing.apple.com
-# Send encapsulated vendor-class specific options. The vendor-class
-# is sent as DHCP option 60, and all the options marked with the
-# vendor class are send encapsulated in DHCP option 43. The meaning of
-# the options is defined by the vendor-class. This example sets the
-# mtftp address to 0.0.0.0 for PXEClients
+# Send RFC-3442 classless static routes (note the netmask encoding)
+#dhcp-option=121,192.168.1.0/24,1.2.3.4,10.0.0.0/8,5.6.7.8
+
+# Send vendor-class specific options encapsulated in DHCP option 43.
+# The meaning of the options is defined by the vendor-class so
+# options are sent only when the client supplied vendor class
+# matches the class given here. (A substring match is OK, so "MSFT"
+# matches "MSFT" and "MSFT 5.0"). This example sets the
+# mtftp address to 0.0.0.0 for PXEClients.
#dhcp-option=vendor:PXEClient,1,0.0.0.0
-# Set the boot filename and tftpd server name and address
-# for BOOTP. You will only need this is you want to
-# boot machines over the network.
+# Send microsoft-specific option to tell windows to release the DHCP lease
+# when it shuts down. Note the "i" flag, to tell dnsmasq to send the
+# value as a four-byte integer - that's what microsoft wants. See
+# http://technet2.microsoft.com/WindowsServer/en/library/a70f1bb7-d2d4-49f0-96d6-4b7414ecfaae1033.mspx?mfr=true
+#dhcp-option=vendor:MSFT,2,1i
+
+# Send the Encapsulated-vendor-class ID needed by some configurations of
+# Etherboot to allow is to recognise the DHCP server.
+#dhcp-option=vendor:Etherboot,60,"Etherboot"
+
+# Send options to PXELinux. Note that we need to send the options even
+# though they don't appear in the parameter request list, so we need
+# to use dhcp-option-force here.
+# See http://syslinux.zytor.com/pxe.php#special for details.
+# Magic number - needed before anything else is recognised
+#dhcp-option-force=208,f1:00:74:7e
+# Configuration file name
+#dhcp-option-force=209,configs/common
+# Path prefix
+#dhcp-option-force=210,/tftpboot/pxelinux/files/
+# Reboot time. (Note 'i' to send 32-bit value)
+#dhcp-option-force=211,30i
+
+# Set the boot filename for netboot/PXE. You will only need
+# this is you want to boot machines over the network and you will need
+# a TFTP server; either dnsmasq's built in TFTP server or an
+# external one. (See below for how to enable the TFTP server.)
+#dhcp-boot=pxelinux.0
+
+# The same as above, but use custom tftp-server instead machine running dnsmasq
+#dhcp-boot=pxelinux,server.name,192.168.1.100
+
+# Boot for Etherboot gPXE. The idea is to send two different
+# filenames, the first loads gPXE, and the second tells gPXE what to
+# load. The dhcp-match sets the gpxe tag for requests from gPXE.
+#dhcp-match=set:gpxe,175 # gPXE sends a 175 option.
+#dhcp-boot=tag:!gpxe,undionly.kpxe
+#dhcp-boot=mybootimage
+
+# Encapsulated options for Etherboot gPXE. All the options are
+# encapsulated within option 175
+#dhcp-option=encap:175, 1, 5b # priority code
+#dhcp-option=encap:175, 176, 1b # no-proxydhcp
+#dhcp-option=encap:175, 177, string # bus-id
+#dhcp-option=encap:175, 189, 1b # BIOS drive code
+#dhcp-option=encap:175, 190, user # iSCSI username
+#dhcp-option=encap:175, 191, pass # iSCSI password
+
+# Test for the architecture of a netboot client. PXE clients are
+# supposed to send their architecture as option 93. (See RFC 4578)
+#dhcp-match=peecees, option:client-arch, 0 #x86-32
+#dhcp-match=itanics, option:client-arch, 2 #IA64
+#dhcp-match=hammers, option:client-arch, 6 #x86-64
+#dhcp-match=mactels, option:client-arch, 7 #EFI x86-64
+
+# Do real PXE, rather than just booting a single file, this is an
+# alternative to dhcp-boot.
+#pxe-prompt="What system shall I netboot?"
+# or with timeout before first available action is taken:
+#pxe-prompt="Press F8 for menu.", 60
+
+# Available boot services. for PXE.
+#pxe-service=x86PC, "Boot from local disk"
+
+# Loads <tftp-root>/pxelinux.0 from dnsmasq TFTP server.
+#pxe-service=x86PC, "Install Linux", pxelinux
+
+# Loads <tftp-root>/pxelinux.0 from TFTP server at 1.2.3.4.
+# Beware this fails on old PXE ROMS.
+#pxe-service=x86PC, "Install Linux", pxelinux, 1.2.3.4
+
+# Use bootserver on network, found my multicast or broadcast.
+#pxe-service=x86PC, "Install windows from RIS server", 1
+
+# Use bootserver at a known IP address.
+#pxe-service=x86PC, "Install windows from RIS server", 1, 1.2.3.4
+
+# If you have multicast-FTP available,
+# information for that can be passed in a similar way using options 1
+# to 5. See page 19 of
+# http://download.intel.com/design/archives/wfm/downloads/pxespec.pdf
+
+
+# Enable dnsmasq's built-in TFTP server
+#enable-tftp
+
+# Set the root directory for files available via FTP.
+#tftp-root=/var/ftpd
+
+# Do not abort if the tftp-root is unavailable
+#tftp-no-fail
+
+# Make the TFTP server more secure: with this set, only files owned by
+# the user dnsmasq is running as will be send over the net.
+#tftp-secure
+
+# This option stops dnsmasq from negotiating a larger blocksize for TFTP
+# transfers. It will slow things down, but may rescue some broken TFTP
+# clients.
+#tftp-no-blocksize
+
+# Set the boot file name only when the "red" tag is set.
+#dhcp-boot=tag:red,pxelinux.red-net
+
+# An example of dhcp-boot with an external TFTP server: the name and IP
+# address of the server are given after the filename.
+# Can fail with old PXE ROMS. Overridden by --pxe-service.
#dhcp-boot=/var/ftpd/pxelinux.0,boothost,192.168.0.3
+# If there are multiple external tftp servers having a same name
+# (using /etc/hosts) then that name can be specified as the
+# tftp_servername (the third option to dhcp-boot) and in that
+# case dnsmasq resolves this name and returns the resultant IP
+# addresses in round robin fasion. This facility can be used to
+# load balance the tftp load among a set of servers.
+#dhcp-boot=/var/ftpd/pxelinux.0,boothost,tftp_server_name
+
# Set the limit on DHCP leases, the default is 150
#dhcp-lease-max=150
# and take over the lease for any client which broadcasts on the network,
# whether it has a record of the lease or not. This avoids long timeouts
# when a machine wakes up on a new network. DO NOT enable this if there's
-# the slighest chance that you might end up accidentally configuring a DHCP
-# server for your campus/company accidentally. The ISC server uses the same
+# the slightest chance that you might end up accidentally configuring a DHCP
+# server for your campus/company accidentally. The ISC server uses
# the same option, and this URL provides more information:
-# http://www.isc.org/index.pl?/sw/dhcp/authoritative.php
+# http://www.isc.org/files/auth.html
#dhcp-authoritative
+# Run an executable when a DHCP lease is created or destroyed.
+# The arguments sent to the script are "add" or "del",
+# then the MAC address, the IP address and finally the hostname
+# if there is one.
+#dhcp-script=/bin/echo
+
# Set the cachesize here.
#cache-size=150
# If you want to disable negative caching, uncomment this.
#no-negcache
-# Normally responses which come form /etc/hosts and the DHCP lease
+# Normally responses which come from /etc/hosts and the DHCP lease
# file have Time-To-Live set as zero, which conventionally means
# do not cache further. If you are happy to trade lower load on the
# server for potentially stale date, you can set a time-to-live (in
#alias=1.2.3.4,5.6.7.8
# and this maps 1.2.3.x to 5.6.7.x
#alias=1.2.3.0,5.6.7.0,255.255.255.0
-
+# and this maps 192.168.0.10->192.168.0.40 to 10.0.0.10->10.0.0.40
+#alias=192.168.0.10-192.168.0.40,10.0.0.0,255.255.255.0
# Change these lines if you want dnsmasq to serve MX records.
# set for this to work.)
# A SRV record sending LDAP for the example.com domain to
-# ldapserver.example.com port 289
+# ldapserver.example.com port 389
#srv-host=_ldap._tcp.example.com,ldapserver.example.com,389
# A SRV record sending LDAP for the example.com domain to
-# ldapserver.example.com port 289 (using domain=)
+# ldapserver.example.com port 389 (using domain=)
#domain=example.com
#srv-host=_ldap._tcp,ldapserver.example.com,389
# example.com
#srv-host=_ldap._tcp.example.com
+# The following line shows how to make dnsmasq serve an arbitrary PTR
+# record. This is useful for DNS-SD. (Note that the
+# domain-name expansion done for SRV records _does_not
+# occur for PTR records.)
+#ptr-record=_http._tcp.dns-sd-services,"New Employee Page._http._tcp.dns-sd-services"
# Change the following lines to enable dnsmasq to serve TXT records.
# These are used for things like SPF and zeroconf. (Note that the
# occur for TXT records.)
#Example SPF.
-#txt-record=example.com,v=spf1 a -all
+#txt-record=example.com,"v=spf1 a -all"
#Example zeroconf
#txt-record=_http._tcp.example.com,name=value,paper=A4
+# Provide an alias for a "local" DNS name. Note that this _only_ works
+# for targets which are names from DHCP or /etc/hosts. Give host
+# "bert" another name, bertrand
+#cname=bertand,bert
# For debugging purposes, log each DNS query as it passes through
# dnsmasq.
#log-queries
-# Include a another lot of configuration options.
+# Log lots of extra information about DHCP transactions.
+#log-dhcp
+
+# Include another lot of configuration options.
#conf-file=/etc/dnsmasq.more.conf
+#conf-dir=/etc/dnsmasq.d
+
+# Include all the files in a directory except those ending in .bak
+#conf-dir=/etc/dnsmasq.d,.bak
+
+# Include all files in a directory which end in .conf
+#conf-dir=/etc/dnsmasq.d/,*.conf
projects / people / ms / dnsmasq.git / blobdiff