[people/ms/u-boot.git] / board / atmel / sama5d3xek / sama5d3xek.c

/*
 * Copyright (C) 2012 - 2013 Atmel Corporation
 * Bo Shen <voice.shen@atmel.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <mmc.h>
#include <asm/io.h>
#include <asm/arch/sama5d3_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_pmc.h>
#include <asm/arch/at91_rstc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/clk.h>
#include <lcd.h>
#include <atmel_hlcdc.h>
#include <atmel_mci.h>
#include <phy.h>
#include <micrel.h>
#include <net.h>
#include <netdev.h>
#include <spl.h>
#include <asm/arch/atmel_mpddrc.h>
#include <asm/arch/at91_wdt.h>

#ifdef CONFIG_USB_GADGET_ATMEL_USBA
#include <asm/arch/atmel_usba_udc.h>
#endif

DECLARE_GLOBAL_DATA_PTR;

/* ------------------------------------------------------------------------- */
/*
 * Miscelaneous platform dependent initialisations
 */

#ifdef CONFIG_NAND_ATMEL
void sama5d3xek_nand_hw_init(void)
{
	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;

	at91_periph_clk_enable(ATMEL_ID_SMC);

	/* Configure SMC CS3 for NAND/SmartMedia */
	writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(1) |
	       AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(1),
	       &smc->cs[3].setup);
	writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) |
	       AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(5),
	       &smc->cs[3].pulse);
	writel(AT91_SMC_CYCLE_NWE(8) | AT91_SMC_CYCLE_NRD(8),
	       &smc->cs[3].cycle);
	writel(AT91_SMC_TIMINGS_TCLR(3) | AT91_SMC_TIMINGS_TADL(10) |
	       AT91_SMC_TIMINGS_TAR(3)  | AT91_SMC_TIMINGS_TRR(4)   |
	       AT91_SMC_TIMINGS_TWB(5)  | AT91_SMC_TIMINGS_RBNSEL(3)|
	       AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings);
	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
	       AT91_SMC_MODE_EXNW_DISABLE |
#ifdef CONFIG_SYS_NAND_DBW_16
	       AT91_SMC_MODE_DBW_16 |
#else /* CONFIG_SYS_NAND_DBW_8 */
	       AT91_SMC_MODE_DBW_8 |
#endif
	       AT91_SMC_MODE_TDF_CYCLE(3),
	       &smc->cs[3].mode);
}
#endif

#ifndef CONFIG_SYS_NO_FLASH
static void sama5d3xek_nor_hw_init(void)
{
	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;

	at91_periph_clk_enable(ATMEL_ID_SMC);

	/* Configure SMC CS0 for NOR flash */
	writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
	       AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
	       &smc->cs[0].setup);
	writel(AT91_SMC_PULSE_NWE(10) | AT91_SMC_PULSE_NCS_WR(11) |
	       AT91_SMC_PULSE_NRD(10) | AT91_SMC_PULSE_NCS_RD(11),
	       &smc->cs[0].pulse);
	writel(AT91_SMC_CYCLE_NWE(11) | AT91_SMC_CYCLE_NRD(14),
	       &smc->cs[0].cycle);
	writel(AT91_SMC_TIMINGS_TCLR(0) | AT91_SMC_TIMINGS_TADL(0)  |
	       AT91_SMC_TIMINGS_TAR(0)  | AT91_SMC_TIMINGS_TRR(0)   |
	       AT91_SMC_TIMINGS_TWB(0)  | AT91_SMC_TIMINGS_RBNSEL(0)|
	       AT91_SMC_TIMINGS_NFSEL(0), &smc->cs[0].timings);
	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
	       AT91_SMC_MODE_EXNW_DISABLE |
	       AT91_SMC_MODE_DBW_16 |
	       AT91_SMC_MODE_TDF_CYCLE(1),
	       &smc->cs[0].mode);

	/* Address pin (A1 ~ A23) configuration */
	at91_set_a_periph(AT91_PIO_PORTE, 1, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 2, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 3, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 4, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 5, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 6, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 7, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 8, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 9, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 10, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 11, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 12, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 13, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 14, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 15, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 16, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 17, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 18, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 19, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 20, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 21, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 22, 0);
	at91_set_a_periph(AT91_PIO_PORTE, 23, 0);
	/* CS0 pin configuration */
	at91_set_a_periph(AT91_PIO_PORTE, 26, 0);
}
#endif

#ifdef CONFIG_CMD_USB
static void sama5d3xek_usb_hw_init(void)
{
	at91_set_pio_output(AT91_PIO_PORTD, 25, 0);
	at91_set_pio_output(AT91_PIO_PORTD, 26, 0);
	at91_set_pio_output(AT91_PIO_PORTD, 27, 0);
}
#endif

#ifdef CONFIG_GENERIC_ATMEL_MCI
static void sama5d3xek_mci_hw_init(void)
{
	at91_mci_hw_init();

	at91_set_pio_output(AT91_PIO_PORTB, 10, 0);	/* MCI0 Power */
}
#endif

#ifdef CONFIG_LCD
vidinfo_t panel_info = {
	.vl_col = 800,
	.vl_row = 480,
	.vl_clk = 24000000,
	.vl_bpix = LCD_BPP,
	.vl_tft = 1,
	.vl_hsync_len = 128,
	.vl_left_margin = 64,
	.vl_right_margin = 64,
	.vl_vsync_len = 2,
	.vl_upper_margin = 22,
	.vl_lower_margin = 21,
	.mmio = ATMEL_BASE_LCDC,
};

void lcd_enable(void)
{
}

void lcd_disable(void)
{
}

static void sama5d3xek_lcd_hw_init(void)
{
	gd->fb_base = CONFIG_SAMA5D3_LCD_BASE;

	/* The higher 8 bit of LCD is board related */
	at91_set_c_periph(AT91_PIO_PORTC, 14, 0);	/* LCDD16 */
	at91_set_c_periph(AT91_PIO_PORTC, 13, 0);	/* LCDD17 */
	at91_set_c_periph(AT91_PIO_PORTC, 12, 0);	/* LCDD18 */
	at91_set_c_periph(AT91_PIO_PORTC, 11, 0);	/* LCDD19 */
	at91_set_c_periph(AT91_PIO_PORTC, 10, 0);	/* LCDD20 */
	at91_set_c_periph(AT91_PIO_PORTC, 15, 0);	/* LCDD21 */
	at91_set_c_periph(AT91_PIO_PORTE, 27, 0);	/* LCDD22 */
	at91_set_c_periph(AT91_PIO_PORTE, 28, 0);	/* LCDD23 */

	/* Configure lower 16 bit of LCD and enable clock */
	at91_lcd_hw_init();
}

#ifdef CONFIG_LCD_INFO
#include <nand.h>
#include <version.h>

void lcd_show_board_info(void)
{
	ulong dram_size;
	uint64_t nand_size;
	int i;
	char temp[32];

	lcd_printf("%s\n", U_BOOT_VERSION);
	lcd_printf("(C) 2013 ATMEL Corp\n");
	lcd_printf("at91@atmel.com\n");
	lcd_printf("%s CPU at %s MHz\n", get_cpu_name(),
		   strmhz(temp, get_cpu_clk_rate()));

	dram_size = 0;
	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
		dram_size += gd->bd->bi_dram[i].size;

	nand_size = 0;
#ifdef CONFIG_NAND_ATMEL
	for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
		nand_size += nand_info[i].size;
#endif
	lcd_printf("%ld MB SDRAM, %lld MB NAND\n",
		   dram_size >> 20, nand_size >> 20);
}
#endif /* CONFIG_LCD_INFO */
#endif /* CONFIG_LCD */

int board_early_init_f(void)
{
	at91_periph_clk_enable(ATMEL_ID_PIOA);
	at91_periph_clk_enable(ATMEL_ID_PIOB);
	at91_periph_clk_enable(ATMEL_ID_PIOC);
	at91_periph_clk_enable(ATMEL_ID_PIOD);
	at91_periph_clk_enable(ATMEL_ID_PIOE);

	at91_seriald_hw_init();

	return 0;
}

int board_init(void)
{
	/* adress of boot parameters */
	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;

#ifdef CONFIG_NAND_ATMEL
	sama5d3xek_nand_hw_init();
#endif
#ifndef CONFIG_SYS_NO_FLASH
	sama5d3xek_nor_hw_init();
#endif
#ifdef CONFIG_CMD_USB
	sama5d3xek_usb_hw_init();
#endif
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
	at91_udp_hw_init();
#endif
#ifdef CONFIG_GENERIC_ATMEL_MCI
	sama5d3xek_mci_hw_init();
#endif
#ifdef CONFIG_ATMEL_SPI
	at91_spi0_hw_init(1 << 0);
#endif
#ifdef CONFIG_MACB
	if (has_emac())
		at91_macb_hw_init();
	if (has_gmac())
		at91_gmac_hw_init();
#endif
#ifdef CONFIG_LCD
	if (has_lcdc())
		sama5d3xek_lcd_hw_init();
#endif
	return 0;
}

int dram_init(void)
{
	gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
				    CONFIG_SYS_SDRAM_SIZE);
	return 0;
}

int board_phy_config(struct phy_device *phydev)
{
	/* board specific timings for GMAC */
	if (has_gmac()) {
		/* rx data delay */
		ksz9021_phy_extended_write(phydev,
					   MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW,
					   0x2222);
		/* tx data delay */
		ksz9021_phy_extended_write(phydev,
					   MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW,
					   0x2222);
		/* rx/tx clock delay */
		ksz9021_phy_extended_write(phydev,
					   MII_KSZ9021_EXT_RGMII_CLOCK_SKEW,
					   0xf2f4);
	}

	/* always run the PHY's config routine */
	if (phydev->drv->config)
		return phydev->drv->config(phydev);

	return 0;
}

int board_eth_init(bd_t *bis)
{
	int rc = 0;

#ifdef CONFIG_MACB
	if (has_emac())
		rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
	if (has_gmac())
		rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC, 0x00);
#endif
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
	usba_udc_probe(&pdata);
#ifdef CONFIG_USB_ETH_RNDIS
	usb_eth_initialize(bis);
#endif
#endif

	return rc;
}

#ifdef CONFIG_GENERIC_ATMEL_MCI
int board_mmc_init(bd_t *bis)
{
	int rc = 0;

	rc = atmel_mci_init((void *)ATMEL_BASE_MCI0);

	return rc;
}
#endif

/* SPI chip select control */
#ifdef CONFIG_ATMEL_SPI
#include <spi.h>

int spi_cs_is_valid(unsigned int bus, unsigned int cs)
{
	return bus == 0 && cs < 4;
}

void spi_cs_activate(struct spi_slave *slave)
{
	switch (slave->cs) {
	case 0:
		at91_set_pio_output(AT91_PIO_PORTD, 13, 0);
	case 1:
		at91_set_pio_output(AT91_PIO_PORTD, 14, 0);
	case 2:
		at91_set_pio_output(AT91_PIO_PORTD, 15, 0);
	case 3:
		at91_set_pio_output(AT91_PIO_PORTD, 16, 0);
	default:
		break;
	}
}

void spi_cs_deactivate(struct spi_slave *slave)
{
	switch (slave->cs) {
	case 0:
		at91_set_pio_output(AT91_PIO_PORTD, 13, 1);
	case 1:
		at91_set_pio_output(AT91_PIO_PORTD, 14, 1);
	case 2:
		at91_set_pio_output(AT91_PIO_PORTD, 15, 1);
	case 3:
		at91_set_pio_output(AT91_PIO_PORTD, 16, 1);
	default:
		break;
	}
}
#endif /* CONFIG_ATMEL_SPI */

/* SPL */
#ifdef CONFIG_SPL_BUILD
void spl_board_init(void)
{
#ifdef CONFIG_SYS_USE_MMC
	sama5d3xek_mci_hw_init();
#elif CONFIG_SYS_USE_NANDFLASH
	sama5d3xek_nand_hw_init();
#elif CONFIG_SYS_USE_SERIALFLASH
	at91_spi0_hw_init(1 << 0);
#endif
}

static void ddr2_conf(struct atmel_mpddr *ddr2)
{
	ddr2->md = (ATMEL_MPDDRC_MD_DBW_32_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);

	ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
		    ATMEL_MPDDRC_CR_NR_ROW_14 |
		    ATMEL_MPDDRC_CR_CAS_DDR_CAS3 |
		    ATMEL_MPDDRC_CR_ENRDM_ON |
		    ATMEL_MPDDRC_CR_NB_8BANKS |
		    ATMEL_MPDDRC_CR_NDQS_DISABLED |
		    ATMEL_MPDDRC_CR_DECOD_INTERLEAVED |
		    ATMEL_MPDDRC_CR_UNAL_SUPPORTED);
	/*
	 * As the DDR2-SDRAm device requires a refresh time is 7.8125us
	 * when DDR run at 133MHz, so it needs (7.8125us * 133MHz / 10^9) clocks
	 */
	ddr2->rtr = 0x411;

	ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |
		      2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |
		      2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET |
		      8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET |
		      2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET |
		      2 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET |
		      2 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET |
		      2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET);

	ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET |
		      200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
		      28 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
		      26 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);

	ddr2->tpr2 = (7 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET |
		      2 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
		      2 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
		      7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
		      8 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
}

void mem_init(void)
{
	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
	struct atmel_mpddr ddr2;

	ddr2_conf(&ddr2);

	/* enable MPDDR clock */
	at91_periph_clk_enable(ATMEL_ID_MPDDRC);
	writel(AT91_PMC_DDR, &pmc->scer);

	/* DDRAM2 Controller initialize */
	ddr2_init(ATMEL_BASE_MPDDRC, ATMEL_BASE_DDRCS, &ddr2);
}

void at91_pmc_init(void)
{
	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
	u32 tmp;

	tmp = AT91_PMC_PLLAR_29 |
	      AT91_PMC_PLLXR_PLLCOUNT(0x3f) |
	      AT91_PMC_PLLXR_MUL(43) |
	      AT91_PMC_PLLXR_DIV(1);
	at91_plla_init(tmp);

	writel(0x3 << 8, &pmc->pllicpr);

	tmp = AT91_PMC_MCKR_MDIV_4 |
	      AT91_PMC_MCKR_CSS_PLLA;
	at91_mck_init(tmp);
}
#endif
Commit	Line	Data
3225f34e BS	1	/*
	2	* Copyright (C) 2012 - 2013 Atmel Corporation
	3	* Bo Shen <voice.shen@atmel.com>
	4	*
1a459660	5	* SPDX-License-Identifier: GPL-2.0+
3225f34e BS	6	*/
	7
	8	#include <common.h>
	9	#include <mmc.h>
	10	#include <asm/io.h>
	11	#include <asm/arch/sama5d3_smc.h>
	12	#include <asm/arch/at91_common.h>
	13	#include <asm/arch/at91_pmc.h>
	14	#include <asm/arch/at91_rstc.h>
	15	#include <asm/arch/gpio.h>
	16	#include <asm/arch/clk.h>
	17	#include <lcd.h>
41e82da1	18	#include <atmel_hlcdc.h>
3225f34e	19	#include <atmel_mci.h>
b719a088	20	#include <phy.h>
e08d6f3a	21	#include <micrel.h>
3225f34e BS	22	#include <net.h>
3225f34e BS	23	#include <netdev.h>
c5e8885a BS	24	#include <spl.h>
	25	#include <asm/arch/atmel_mpddrc.h>
	26	#include <asm/arch/at91_wdt.h>
3225f34e	27
3668ce3c BS	28	#ifdef CONFIG_USB_GADGET_ATMEL_USBA
	29	#include <asm/arch/atmel_usba_udc.h>
	30	#endif
	31
3225f34e BS	32	DECLARE_GLOBAL_DATA_PTR;
	33
	34	/* ------------------------------------------------------------------------- */
	35	/*
	36	* Miscelaneous platform dependent initialisations
	37	*/
	38
	39	#ifdef CONFIG_NAND_ATMEL
	40	void sama5d3xek_nand_hw_init(void)
	41	{
	42	struct at91_smc smc = (struct at91_smc )ATMEL_BASE_SMC;
	43
	44	at91_periph_clk_enable(ATMEL_ID_SMC);
	45
	46	/* Configure SMC CS3 for NAND/SmartMedia */
	47	writel(AT91_SMC_SETUP_NWE(2) \| AT91_SMC_SETUP_NCS_WR(1) \|
	48	AT91_SMC_SETUP_NRD(2) \| AT91_SMC_SETUP_NCS_RD(1),
	49	&smc->cs[3].setup);
	50	writel(AT91_SMC_PULSE_NWE(3) \| AT91_SMC_PULSE_NCS_WR(5) \|
	51	AT91_SMC_PULSE_NRD(3) \| AT91_SMC_PULSE_NCS_RD(5),
	52	&smc->cs[3].pulse);
	53	writel(AT91_SMC_CYCLE_NWE(8) \| AT91_SMC_CYCLE_NRD(8),
	54	&smc->cs[3].cycle);
	55	writel(AT91_SMC_TIMINGS_TCLR(3) \| AT91_SMC_TIMINGS_TADL(10) \|
	56	AT91_SMC_TIMINGS_TAR(3) \| AT91_SMC_TIMINGS_TRR(4) \|
	57	AT91_SMC_TIMINGS_TWB(5) \| AT91_SMC_TIMINGS_RBNSEL(3)\|
	58	AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings);
	59	writel(AT91_SMC_MODE_RM_NRD \| AT91_SMC_MODE_WM_NWE \|
	60	AT91_SMC_MODE_EXNW_DISABLE \|
	61	#ifdef CONFIG_SYS_NAND_DBW_16
	62	AT91_SMC_MODE_DBW_16 \|
	63	#else /* CONFIG_SYS_NAND_DBW_8 */
	64	AT91_SMC_MODE_DBW_8 \|
	65	#endif
	66	AT91_SMC_MODE_TDF_CYCLE(3),
	67	&smc->cs[3].mode);
	68	}
	69	#endif
	70
a931b137 BS	71	#ifndef CONFIG_SYS_NO_FLASH
	72	static void sama5d3xek_nor_hw_init(void)
	73	{
	74	struct at91_smc smc = (struct at91_smc )ATMEL_BASE_SMC;
	75
	76	at91_periph_clk_enable(ATMEL_ID_SMC);
	77
	78	/* Configure SMC CS0 for NOR flash */
	79	writel(AT91_SMC_SETUP_NWE(1) \| AT91_SMC_SETUP_NCS_WR(0) \|
	80	AT91_SMC_SETUP_NRD(2) \| AT91_SMC_SETUP_NCS_RD(0),
	81	&smc->cs[0].setup);
	82	writel(AT91_SMC_PULSE_NWE(10) \| AT91_SMC_PULSE_NCS_WR(11) \|
	83	AT91_SMC_PULSE_NRD(10) \| AT91_SMC_PULSE_NCS_RD(11),
	84	&smc->cs[0].pulse);
	85	writel(AT91_SMC_CYCLE_NWE(11) \| AT91_SMC_CYCLE_NRD(14),
	86	&smc->cs[0].cycle);
	87	writel(AT91_SMC_TIMINGS_TCLR(0) \| AT91_SMC_TIMINGS_TADL(0) \|
	88	AT91_SMC_TIMINGS_TAR(0) \| AT91_SMC_TIMINGS_TRR(0) \|
	89	AT91_SMC_TIMINGS_TWB(0) \| AT91_SMC_TIMINGS_RBNSEL(0)\|
	90	AT91_SMC_TIMINGS_NFSEL(0), &smc->cs[0].timings);
	91	writel(AT91_SMC_MODE_RM_NRD \| AT91_SMC_MODE_WM_NWE \|
	92	AT91_SMC_MODE_EXNW_DISABLE \|
	93	AT91_SMC_MODE_DBW_16 \|
	94	AT91_SMC_MODE_TDF_CYCLE(1),
	95	&smc->cs[0].mode);
	96
	97	/* Address pin (A1 ~ A23) configuration */
	98	at91_set_a_periph(AT91_PIO_PORTE, 1, 0);
	99	at91_set_a_periph(AT91_PIO_PORTE, 2, 0);
	100	at91_set_a_periph(AT91_PIO_PORTE, 3, 0);
	101	at91_set_a_periph(AT91_PIO_PORTE, 4, 0);
	102	at91_set_a_periph(AT91_PIO_PORTE, 5, 0);
	103	at91_set_a_periph(AT91_PIO_PORTE, 6, 0);
	104	at91_set_a_periph(AT91_PIO_PORTE, 7, 0);
	105	at91_set_a_periph(AT91_PIO_PORTE, 8, 0);
	106	at91_set_a_periph(AT91_PIO_PORTE, 9, 0);
	107	at91_set_a_periph(AT91_PIO_PORTE, 10, 0);
	108	at91_set_a_periph(AT91_PIO_PORTE, 11, 0);
	109	at91_set_a_periph(AT91_PIO_PORTE, 12, 0);
	110	at91_set_a_periph(AT91_PIO_PORTE, 13, 0);
	111	at91_set_a_periph(AT91_PIO_PORTE, 14, 0);
	112	at91_set_a_periph(AT91_PIO_PORTE, 15, 0);
	113	at91_set_a_periph(AT91_PIO_PORTE, 16, 0);
	114	at91_set_a_periph(AT91_PIO_PORTE, 17, 0);
	115	at91_set_a_periph(AT91_PIO_PORTE, 18, 0);
	116	at91_set_a_periph(AT91_PIO_PORTE, 19, 0);
	117	at91_set_a_periph(AT91_PIO_PORTE, 20, 0);
	118	at91_set_a_periph(AT91_PIO_PORTE, 21, 0);
	119	at91_set_a_periph(AT91_PIO_PORTE, 22, 0);
	120	at91_set_a_periph(AT91_PIO_PORTE, 23, 0);
	121	/* CS0 pin configuration */
	122	at91_set_a_periph(AT91_PIO_PORTE, 26, 0);
	123	}
	124	#endif
	125
3225f34e BS	126	#ifdef CONFIG_CMD_USB
	127	static void sama5d3xek_usb_hw_init(void)
	128	{
	129	at91_set_pio_output(AT91_PIO_PORTD, 25, 0);
	130	at91_set_pio_output(AT91_PIO_PORTD, 26, 0);
	131	at91_set_pio_output(AT91_PIO_PORTD, 27, 0);
	132	}
	133	#endif
	134
	135	#ifdef CONFIG_GENERIC_ATMEL_MCI
	136	static void sama5d3xek_mci_hw_init(void)
	137	{
	138	at91_mci_hw_init();
	139
	140	at91_set_pio_output(AT91_PIO_PORTB, 10, 0); /* MCI0 Power */
	141	}
	142	#endif
	143
	144	#ifdef CONFIG_LCD
	145	vidinfo_t panel_info = {
	146	.vl_col = 800,
	147	.vl_row = 480,
	148	.vl_clk = 24000000,
3225f34e BS	149	.vl_bpix = LCD_BPP,
	150	.vl_tft = 1,
	151	.vl_hsync_len = 128,
	152	.vl_left_margin = 64,
	153	.vl_right_margin = 64,
	154	.vl_vsync_len = 2,
	155	.vl_upper_margin = 22,
	156	.vl_lower_margin = 21,
	157	.mmio = ATMEL_BASE_LCDC,
	158	};
	159
	160	void lcd_enable(void)
	161	{
	162	}
	163
	164	void lcd_disable(void)
	165	{
	166	}
	167
	168	static void sama5d3xek_lcd_hw_init(void)
	169	{
	170	gd->fb_base = CONFIG_SAMA5D3_LCD_BASE;
	171
	172	/* The higher 8 bit of LCD is board related */
	173	at91_set_c_periph(AT91_PIO_PORTC, 14, 0); /* LCDD16 */
	174	at91_set_c_periph(AT91_PIO_PORTC, 13, 0); /* LCDD17 */
	175	at91_set_c_periph(AT91_PIO_PORTC, 12, 0); /* LCDD18 */
	176	at91_set_c_periph(AT91_PIO_PORTC, 11, 0); /* LCDD19 */
	177	at91_set_c_periph(AT91_PIO_PORTC, 10, 0); /* LCDD20 */
	178	at91_set_c_periph(AT91_PIO_PORTC, 15, 0); /* LCDD21 */
	179	at91_set_c_periph(AT91_PIO_PORTE, 27, 0); /* LCDD22 */
	180	at91_set_c_periph(AT91_PIO_PORTE, 28, 0); /* LCDD23 */
	181
	182	/* Configure lower 16 bit of LCD and enable clock */
	183	at91_lcd_hw_init();
	184	}
	185
	186	#ifdef CONFIG_LCD_INFO
	187	#include <nand.h>
	188	#include <version.h>
	189
	190	void lcd_show_board_info(void)
	191	{
d02a60a1 WJ	192	ulong dram_size;
d02a60a1 WJ	193	uint64_t nand_size;
3225f34e BS	194	int i;
	195	char temp[32];
	196
	197	lcd_printf("%s\n", U_BOOT_VERSION);
	198	lcd_printf("(C) 2013 ATMEL Corp\n");
	199	lcd_printf("at91@atmel.com\n");
	200	lcd_printf("%s CPU at %s MHz\n", get_cpu_name(),
	201	strmhz(temp, get_cpu_clk_rate()));
	202
	203	dram_size = 0;
	204	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
	205	dram_size += gd->bd->bi_dram[i].size;
	206
	207	nand_size = 0;
	208	#ifdef CONFIG_NAND_ATMEL
	209	for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
	210	nand_size += nand_info[i].size;
	211	#endif
d02a60a1	212	lcd_printf("%ld MB SDRAM, %lld MB NAND\n",
3225f34e BS	213	dram_size >> 20, nand_size >> 20);
	214	}
	215	#endif /* CONFIG_LCD_INFO */
	216	#endif /* CONFIG_LCD */
	217
	218	int board_early_init_f(void)
	219	{
d2acb986 BS	220	at91_periph_clk_enable(ATMEL_ID_PIOA);
	221	at91_periph_clk_enable(ATMEL_ID_PIOB);
	222	at91_periph_clk_enable(ATMEL_ID_PIOC);
	223	at91_periph_clk_enable(ATMEL_ID_PIOD);
	224	at91_periph_clk_enable(ATMEL_ID_PIOE);
	225
3225f34e BS	226	at91_seriald_hw_init();
	227
	228	return 0;
	229	}
	230
	231	int board_init(void)
	232	{
	233	/* adress of boot parameters */
	234	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
	235
	236	#ifdef CONFIG_NAND_ATMEL
	237	sama5d3xek_nand_hw_init();
	238	#endif
a931b137 BS	239	#ifndef CONFIG_SYS_NO_FLASH
	240	sama5d3xek_nor_hw_init();
	241	#endif
3225f34e BS	242	#ifdef CONFIG_CMD_USB
	243	sama5d3xek_usb_hw_init();
	244	#endif
3668ce3c BS	245	#ifdef CONFIG_USB_GADGET_ATMEL_USBA
	246	at91_udp_hw_init();
	247	#endif
3225f34e BS	248	#ifdef CONFIG_GENERIC_ATMEL_MCI
	249	sama5d3xek_mci_hw_init();
	250	#endif
	251	#ifdef CONFIG_ATMEL_SPI
	252	at91_spi0_hw_init(1 << 0);
	253	#endif
	254	#ifdef CONFIG_MACB
	255	if (has_emac())
	256	at91_macb_hw_init();
e08d6f3a BS	257	if (has_gmac())
e08d6f3a BS	258	at91_gmac_hw_init();
3225f34e BS	259	#endif
	260	#ifdef CONFIG_LCD
	261	if (has_lcdc())
	262	sama5d3xek_lcd_hw_init();
	263	#endif
	264	return 0;
	265	}
	266
	267	int dram_init(void)
	268	{
	269	gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
	270	CONFIG_SYS_SDRAM_SIZE);
	271	return 0;
	272	}
	273
e08d6f3a BS	274	int board_phy_config(struct phy_device *phydev)
e08d6f3a BS	275	{
b719a088 AB	276	/* board specific timings for GMAC */
	277	if (has_gmac()) {
	278	/* rx data delay */
	279	ksz9021_phy_extended_write(phydev,
	280	MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW,
	281	0x2222);
	282	/* tx data delay */
	283	ksz9021_phy_extended_write(phydev,
	284	MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW,
	285	0x2222);
	286	/* rx/tx clock delay */
	287	ksz9021_phy_extended_write(phydev,
	288	MII_KSZ9021_EXT_RGMII_CLOCK_SKEW,
	289	0xf2f4);
	290	}
	291
	292	/* always run the PHY's config routine */
	293	if (phydev->drv->config)
	294	return phydev->drv->config(phydev);
e08d6f3a BS	295
	296	return 0;
	297	}
	298
3225f34e BS	299	int board_eth_init(bd_t *bis)
	300	{
	301	int rc = 0;
	302
	303	#ifdef CONFIG_MACB
	304	if (has_emac())
	305	rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
e08d6f3a BS	306	if (has_gmac())
e08d6f3a BS	307	rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC, 0x00);
3668ce3c BS	308	#endif
	309	#ifdef CONFIG_USB_GADGET_ATMEL_USBA
	310	usba_udc_probe(&pdata);
	311	#ifdef CONFIG_USB_ETH_RNDIS
	312	usb_eth_initialize(bis);
	313	#endif
3225f34e BS	314	#endif
	315
	316	return rc;
	317	}
	318
	319	#ifdef CONFIG_GENERIC_ATMEL_MCI
	320	int board_mmc_init(bd_t *bis)
	321	{
	322	int rc = 0;
	323
	324	rc = atmel_mci_init((void *)ATMEL_BASE_MCI0);
	325
	326	return rc;
	327	}
	328	#endif
	329
	330	/* SPI chip select control */
	331	#ifdef CONFIG_ATMEL_SPI
	332	#include <spi.h>
	333
	334	int spi_cs_is_valid(unsigned int bus, unsigned int cs)
	335	{
	336	return bus == 0 && cs < 4;
	337	}
	338
	339	void spi_cs_activate(struct spi_slave *slave)
	340	{
	341	switch (slave->cs) {
	342	case 0:
	343	at91_set_pio_output(AT91_PIO_PORTD, 13, 0);
	344	case 1:
	345	at91_set_pio_output(AT91_PIO_PORTD, 14, 0);
	346	case 2:
	347	at91_set_pio_output(AT91_PIO_PORTD, 15, 0);
	348	case 3:
	349	at91_set_pio_output(AT91_PIO_PORTD, 16, 0);
	350	default:
	351	break;
	352	}
	353	}
	354
	355	void spi_cs_deactivate(struct spi_slave *slave)
	356	{
	357	switch (slave->cs) {
	358	case 0:
	359	at91_set_pio_output(AT91_PIO_PORTD, 13, 1);
	360	case 1:
	361	at91_set_pio_output(AT91_PIO_PORTD, 14, 1);
	362	case 2:
	363	at91_set_pio_output(AT91_PIO_PORTD, 15, 1);
	364	case 3:
	365	at91_set_pio_output(AT91_PIO_PORTD, 16, 1);
	366	default:
	367	break;
	368	}
	369	}
	370	#endif /* CONFIG_ATMEL_SPI */
c5e8885a BS	371
	372	/* SPL */
	373	#ifdef CONFIG_SPL_BUILD
	374	void spl_board_init(void)
	375	{
	376	#ifdef CONFIG_SYS_USE_MMC
	377	sama5d3xek_mci_hw_init();
27019e4a BS	378	#elif CONFIG_SYS_USE_NANDFLASH
27019e4a BS	379	sama5d3xek_nand_hw_init();
8a45b0ba BS	380	#elif CONFIG_SYS_USE_SERIALFLASH
8a45b0ba BS	381	at91_spi0_hw_init(1 << 0);
c5e8885a BS	382	#endif
	383	}
	384
	385	static void ddr2_conf(struct atmel_mpddr *ddr2)
	386	{
	387	ddr2->md = (ATMEL_MPDDRC_MD_DBW_32_BITS \| ATMEL_MPDDRC_MD_DDR2_SDRAM);
	388
	389	ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 \|
	390	ATMEL_MPDDRC_CR_NR_ROW_14 \|
	391	ATMEL_MPDDRC_CR_CAS_DDR_CAS3 \|
	392	ATMEL_MPDDRC_CR_ENRDM_ON \|
	393	ATMEL_MPDDRC_CR_NB_8BANKS \|
	394	ATMEL_MPDDRC_CR_NDQS_DISABLED \|
	395	ATMEL_MPDDRC_CR_DECOD_INTERLEAVED \|
	396	ATMEL_MPDDRC_CR_UNAL_SUPPORTED);
	397	/*
	398	* As the DDR2-SDRAm device requires a refresh time is 7.8125us
	399	* when DDR run at 133MHz, so it needs (7.8125us * 133MHz / 10^9) clocks
	400	*/
	401	ddr2->rtr = 0x411;
	402
	403	ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET \|
	404	2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET \|
	405	2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET \|
	406	8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET \|
	407	2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET \|
	408	2 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET \|
	409	2 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET \|
	410	2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET);
	411
	412	ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET \|
	413	200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET \|
	414	28 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET \|
	415	26 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
	416
	417	ddr2->tpr2 = (7 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET \|
	418	2 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET \|
	419	2 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET \|
	420	7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET \|
	421	8 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
	422	}
	423
	424	void mem_init(void)
	425	{
	426	struct at91_pmc pmc = (struct at91_pmc )ATMEL_BASE_PMC;
	427	struct atmel_mpddr ddr2;
	428
	429	ddr2_conf(&ddr2);
	430
	431	/* enable MPDDR clock */
	432	at91_periph_clk_enable(ATMEL_ID_MPDDRC);
c982f6b9	433	writel(AT91_PMC_DDR, &pmc->scer);
c5e8885a BS	434
c5e8885a BS	435	/* DDRAM2 Controller initialize */
0c01c3e8	436	ddr2_init(ATMEL_BASE_MPDDRC, ATMEL_BASE_DDRCS, &ddr2);
c5e8885a BS	437	}
	438
	439	void at91_pmc_init(void)
	440	{
	441	struct at91_pmc pmc = (struct at91_pmc )ATMEL_BASE_PMC;
	442	u32 tmp;
	443
	444	tmp = AT91_PMC_PLLAR_29 \|
	445	AT91_PMC_PLLXR_PLLCOUNT(0x3f) \|
	446	AT91_PMC_PLLXR_MUL(43) \|
	447	AT91_PMC_PLLXR_DIV(1);
	448	at91_plla_init(tmp);
	449
	450	writel(0x3 << 8, &pmc->pllicpr);
	451
	452	tmp = AT91_PMC_MCKR_MDIV_4 \|
	453	AT91_PMC_MCKR_CSS_PLLA;
	454	at91_mck_init(tmp);
	455	}
	456	#endif