[people/ms/u-boot.git] / include / configs / vme8349.h

/*
 * esd vme8349 U-Boot configuration file
 * Copyright (c) 2008, 2009 esd gmbh Hannover Germany
 *
 * (C) Copyright 2006-2010
 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 *
 * reinhard.arlt@esd-electronics.de
 * Based on the MPC8349EMDS config.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/*
 * vme8349 board configuration file.
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#define CONFIG_DISPLAY_BOARDINFO

/*
 * Top level Makefile configuration choices
 */
#ifdef CONFIG_CADDY2
#define VME_CADDY2
#endif

/*
 * High Level Configuration Options
 */
#define CONFIG_E300		1	/* E300 Family */
#define CONFIG_MPC834x		1	/* MPC834x family */
#define CONFIG_MPC8349		1	/* MPC8349 specific */
#define CONFIG_VME8349		1	/* ESD VME8349 board specific */

#define	CONFIG_SYS_TEXT_BASE	0xFFF00000

#define CONFIG_MISC_INIT_R

#define CONFIG_PCI
/* Don't enable PCI2 on vme834x - it doesn't exist physically. */
#undef CONFIG_MPC83XX_PCI2		/* support for 2nd PCI controller */

#define CONFIG_PCI_66M
#ifdef CONFIG_PCI_66M
#define CONFIG_83XX_CLKIN	66000000	/* in Hz */
#else
#define CONFIG_83XX_CLKIN	33000000	/* in Hz */
#endif

#ifndef CONFIG_SYS_CLK_FREQ
#ifdef CONFIG_PCI_66M
#define CONFIG_SYS_CLK_FREQ	66000000
#define HRCWL_CSB_TO_CLKIN	HRCWL_CSB_TO_CLKIN_4X1
#else
#define CONFIG_SYS_CLK_FREQ	33000000
#define HRCWL_CSB_TO_CLKIN	HRCWL_CSB_TO_CLKIN_8X1
#endif
#endif

#define CONFIG_SYS_IMMR		0xE0000000

#undef CONFIG_SYS_DRAM_TEST			/* memory test, takes time */
#define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest region */
#define CONFIG_SYS_MEMTEST_END		0x00100000

/*
 * DDR Setup
 */
#define CONFIG_DDR_ECC			/* only for ECC DDR module */
#define CONFIG_DDR_ECC_CMD		/* use DDR ECC user commands */
#define CONFIG_SPD_EEPROM
#define SPD_EEPROM_ADDRESS		0x54
#define CONFIG_SYS_READ_SPD		vme8349_read_spd
#define CONFIG_SYS_83XX_DDR_USES_CS0	/* esd; Fsl board uses CS2/CS3 */

/*
 * 32-bit data path mode.
 *
 * Please note that using this mode for devices with the real density of 64-bit
 * effectively reduces the amount of available memory due to the effect of
 * wrapping around while translating address to row/columns, for example in the
 * 256MB module the upper 128MB get aliased with contents of the lower
 * 128MB); normally this define should be used for devices with real 32-bit
 * data path.
 */
#undef CONFIG_DDR_32BIT

#define CONFIG_SYS_DDR_BASE		0x00000000	/* DDR is sys memory*/
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN \
					| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
#define CONFIG_DDR_2T_TIMING
#define CONFIG_SYS_DDRCDR		(DDRCDR_DHC_EN \
					| DDRCDR_ODT \
					| DDRCDR_Q_DRN)
					/* 0x80080001 */

/*
 * FLASH on the Local Bus
 */
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER			        /* use the CFI driver */
#ifdef VME_CADDY2
#define CONFIG_SYS_FLASH_BASE		0xffc00000	/* start of FLASH   */
#define CONFIG_SYS_FLASH_SIZE		4		/* flash size in MB */
#define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE | \
					 BR_PS_16 |	/*  16bit */ \
					 BR_MS_GPCM |	/*  MSEL = GPCM */ \
					 BR_V)		/* valid */

#define CONFIG_SYS_OR0_PRELIM		(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
					| OR_GPCM_XAM \
					| OR_GPCM_CSNT \
					| OR_GPCM_ACS_DIV2 \
					| OR_GPCM_XACS \
					| OR_GPCM_SCY_15 \
					| OR_GPCM_TRLX_SET \
					| OR_GPCM_EHTR_SET \
					| OR_GPCM_EAD)
					/* 0xffc06ff7 */
#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_4MB)
#else
#define CONFIG_SYS_FLASH_BASE		0xf8000000	/* start of FLASH   */
#define CONFIG_SYS_FLASH_SIZE		128		/* flash size in MB */
#define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE | \
					 BR_PS_16 |	/*  16bit */ \
					 BR_MS_GPCM |	/*  MSEL = GPCM */ \
					 BR_V)		/* valid */

#define CONFIG_SYS_OR0_PRELIM		(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
					| OR_GPCM_XAM \
					| OR_GPCM_CSNT \
					| OR_GPCM_ACS_DIV2 \
					| OR_GPCM_XACS \
					| OR_GPCM_SCY_15 \
					| OR_GPCM_TRLX_SET \
					| OR_GPCM_EHTR_SET \
					| OR_GPCM_EAD)
					/* 0xf8006ff7 */
#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_128MB)
#endif
/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */

#define CONFIG_SYS_WINDOW1_BASE		0xf0000000
#define CONFIG_SYS_BR1_PRELIM		(CONFIG_SYS_WINDOW1_BASE \
					| BR_PS_32 \
					| BR_MS_GPCM \
					| BR_V)
					/* 0xF0001801 */
#define CONFIG_SYS_OR1_PRELIM		(OR_AM_256KB \
					| OR_GPCM_SETA)
					/* 0xfffc0208 */
#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_WINDOW1_BASE
#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_256KB)

#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device*/

#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase TO (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write TO (ms) */

#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */

#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#else
#undef CONFIG_SYS_RAMBOOT
#endif

#define CONFIG_SYS_INIT_RAM_LOCK	1
#define CONFIG_SYS_INIT_RAM_ADDR	0xF7000000	/* Initial RAM addr */
#define CONFIG_SYS_INIT_RAM_SIZE		0x1000		/* size */

#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
					 GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB */
#define CONFIG_SYS_MALLOC_LEN		(256 * 1024)	/* Malloc size */

/*
 * Local Bus LCRR and LBCR regs
 *    LCRR:  no DLL bypass, Clock divider is 4
 * External Local Bus rate is
 *    CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
 */
#define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR	0x00000000

#undef CONFIG_SYS_LB_SDRAM	/* if board has SDRAM on local bus */

/*
 * Serial Port
 */
#define CONFIG_CONS_INDEX	1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

#define CONFIG_SYS_BAUDRATE_TABLE  \
		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

#define CONFIG_SYS_NS16550_COM1		(CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2		(CONFIG_SYS_IMMR + 0x4600)

#define CONFIG_CMDLINE_EDITING		/* add command line history	*/
#define CONFIG_AUTO_COMPLETE		/* add autocompletion support */

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED	400000
#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
#define CONFIG_SYS_FSL_I2C2_SPEED	400000
#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */

#define CONFIG_SYS_I2C_8574_ADDR2       0x20    /* I2C1, PCF8574 */

/* TSEC */
#define CONFIG_SYS_TSEC1_OFFSET	0x24000
#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
#define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)

/*
 * General PCI
 * Addresses are mapped 1-1.
 */
#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
#define CONFIG_SYS_PCI1_IO_BASE		0x00000000
#define CONFIG_SYS_PCI1_IO_PHYS		0xE2000000
#define CONFIG_SYS_PCI1_IO_SIZE		0x00100000	/* 1M */

#define CONFIG_SYS_PCI2_MEM_BASE	0xA0000000
#define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
#define CONFIG_SYS_PCI2_MEM_SIZE	0x10000000	/* 256M */
#define CONFIG_SYS_PCI2_MMIO_BASE	0xB0000000
#define CONFIG_SYS_PCI2_MMIO_PHYS	CONFIG_SYS_PCI2_MMIO_BASE
#define CONFIG_SYS_PCI2_MMIO_SIZE	0x10000000	/* 256M */
#define CONFIG_SYS_PCI2_IO_BASE		0x00000000
#define CONFIG_SYS_PCI2_IO_PHYS		0xE2100000
#define CONFIG_SYS_PCI2_IO_SIZE		0x00100000	/* 1M */

#if defined(CONFIG_PCI)

#define PCI_64BIT
#define PCI_ONE_PCI1
#if defined(PCI_64BIT)
#undef PCI_ALL_PCI1
#undef PCI_TWO_PCI1
#undef PCI_ONE_PCI1
#endif

#ifndef VME_CADDY2
#endif
#define CONFIG_PCI_PNP		/* do pci plug-and-play */

#undef CONFIG_EEPRO100
#undef CONFIG_TULIP

#if !defined(CONFIG_PCI_PNP)
	#define PCI_ENET0_IOADDR	0xFIXME
	#define PCI_ENET0_MEMADDR	0xFIXME
	#define PCI_IDSEL_NUMBER	0xFIXME
#endif

#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID	0x1957	/* Freescale */

#endif	/* CONFIG_PCI */

/*
 * TSEC configuration
 */
#ifdef VME_CADDY2
#else
#define CONFIG_TSEC_ENET		/* TSEC ethernet support */
#endif

#if defined(CONFIG_TSEC_ENET)

#define CONFIG_GMII			/* MII PHY management */
#define CONFIG_TSEC1
#define CONFIG_TSEC1_NAME	"TSEC0"
#define CONFIG_TSEC2
#define CONFIG_TSEC2_NAME	"TSEC1"
#define CONFIG_PHY_M88E1111
#define TSEC1_PHY_ADDR		0x08
#define TSEC2_PHY_ADDR		0x10
#define TSEC1_PHYIDX		0
#define TSEC2_PHYIDX		0
#define TSEC1_FLAGS		TSEC_GIGABIT
#define TSEC2_FLAGS		TSEC_GIGABIT

/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME		"TSEC0"

#endif	/* CONFIG_TSEC_ENET */

/*
 * Environment
 */
#ifndef CONFIG_SYS_RAMBOOT
	#define CONFIG_ENV_IS_IN_FLASH
	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0xc0000)
	#define CONFIG_ENV_SECT_SIZE	0x20000	/* 128K(one sector) for env */
	#define CONFIG_ENV_SIZE		0x2000

/* Address and size of Redundant Environment Sector	*/
#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)

#else
	#define CONFIG_SYS_NO_FLASH		/* Flash is not usable now */
	#define CONFIG_ENV_IS_NOWHERE		/* Store ENV in memory only */
	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
	#define CONFIG_ENV_SIZE		0x2000
#endif

#define CONFIG_LOADS_ECHO		/* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME

/*
 * Command line configuration.
 */
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_DATE
#define CONFIG_SYS_RTC_BUS_NUM  0x01
#define CONFIG_SYS_I2C_RTC_ADDR	0x32
#define CONFIG_RTC_RX8025
#define CONFIG_CMD_TSI148

#if defined(CONFIG_PCI)
    #define CONFIG_CMD_PCI
#endif

#if defined(CONFIG_SYS_RAMBOOT)
    #undef CONFIG_CMD_ENV
#endif

/* Pass Ethernet MAC to VxWorks */
#define CONFIG_SYS_VXWORKS_MAC_PTR	0x000043f0

#undef CONFIG_WATCHDOG			/* watchdog disabled */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */

#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE	1024	/* Console I/O Buffer Size */
#else
	#define CONFIG_SYS_CBSIZE	256	/* Console I/O Buffer Size */
#endif

#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS	16		/* max num of command args */
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE /* Boot Argument Buf Size */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 256 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ	(256 << 20)	/* Init Memory map for Linux*/

#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */

#define CONFIG_SYS_HRCW_LOW (\
	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
	HRCWL_DDR_TO_SCB_CLK_1X1 |\
	HRCWL_CSB_TO_CLKIN |\
	HRCWL_VCO_1X2 |\
	HRCWL_CORE_TO_CSB_2X1)

#if defined(PCI_64BIT)
#define CONFIG_SYS_HRCW_HIGH (\
	HRCWH_PCI_HOST |\
	HRCWH_64_BIT_PCI |\
	HRCWH_PCI1_ARBITER_ENABLE |\
	HRCWH_PCI2_ARBITER_DISABLE |\
	HRCWH_CORE_ENABLE |\
	HRCWH_FROM_0X00000100 |\
	HRCWH_BOOTSEQ_DISABLE |\
	HRCWH_SW_WATCHDOG_DISABLE |\
	HRCWH_ROM_LOC_LOCAL_16BIT |\
	HRCWH_TSEC1M_IN_GMII |\
	HRCWH_TSEC2M_IN_GMII)
#else
#define CONFIG_SYS_HRCW_HIGH (\
	HRCWH_PCI_HOST |\
	HRCWH_32_BIT_PCI |\
	HRCWH_PCI1_ARBITER_ENABLE |\
	HRCWH_PCI2_ARBITER_ENABLE |\
	HRCWH_CORE_ENABLE |\
	HRCWH_FROM_0X00000100 |\
	HRCWH_BOOTSEQ_DISABLE |\
	HRCWH_SW_WATCHDOG_DISABLE |\
	HRCWH_ROM_LOC_LOCAL_16BIT |\
	HRCWH_TSEC1M_IN_GMII |\
	HRCWH_TSEC2M_IN_GMII)
#endif

/* System IO Config */
#define CONFIG_SYS_SICRH 0
#define CONFIG_SYS_SICRL SICRL_LDP_A

#define CONFIG_SYS_HID0_INIT	0x000000000
#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
				 HID0_ENABLE_INSTRUCTION_CACHE)

#define CONFIG_SYS_HID2		HID2_HBE

#define CONFIG_SYS_GPIO1_PRELIM
#define CONFIG_SYS_GPIO1_DIR	0x00100000
#define CONFIG_SYS_GPIO1_DAT	0x00100000

#define CONFIG_SYS_GPIO2_PRELIM
#define CONFIG_SYS_GPIO2_DIR	0x78900000
#define CONFIG_SYS_GPIO2_DAT	0x70100000

#define CONFIG_HIGH_BATS		/* High BATs supported */

/* DDR @ 0x00000000 */
#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
				 BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
				 BATU_VS | BATU_VP)

/* PCI @ 0x80000000 */
#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW | \
				 BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | \
				 BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_RW | \
				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | \
				 BATU_VS | BATU_VP)
#else
#define CONFIG_SYS_IBAT1L	(0)
#define CONFIG_SYS_IBAT1U	(0)
#define CONFIG_SYS_IBAT2L	(0)
#define CONFIG_SYS_IBAT2U	(0)
#endif

#ifdef CONFIG_MPC83XX_PCI2
#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_PCI2_MEM_BASE | BATL_PP_RW | \
				 BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_PCI2_MEM_BASE | BATU_BL_256M | \
				 BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCI2_MMIO_BASE | BATL_PP_RW | \
				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_PCI2_MMIO_BASE | BATU_BL_256M | \
				 BATU_VS | BATU_VP)
#else
#define CONFIG_SYS_IBAT3L	(0)
#define CONFIG_SYS_IBAT3U	(0)
#define CONFIG_SYS_IBAT4L	(0)
#define CONFIG_SYS_IBAT4U	(0)
#endif

/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_IMMR | BATL_PP_RW | \
				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_IMMR | BATU_BL_256M | \
				 BATU_VS | BATU_VP)

#define CONFIG_SYS_IBAT6L	(0xF0000000 | BATL_PP_RW | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT6U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)

#if (CONFIG_SYS_DDR_SIZE == 512)
#define CONFIG_SYS_IBAT7L	(CONFIG_SYS_SDRAM_BASE+0x10000000 | \
				 BATL_PP_RW | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT7U	(CONFIG_SYS_SDRAM_BASE+0x10000000 | \
				 BATU_BL_256M | BATU_VS | BATU_VP)
#else
#define CONFIG_SYS_IBAT7L	(0)
#define CONFIG_SYS_IBAT7U	(0)
#endif

#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
#endif

/*
 * Environment Configuration
 */
#define CONFIG_ENV_OVERWRITE

#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#endif

#define CONFIG_HOSTNAME		VME8349
#define CONFIG_ROOTPATH		"/tftpboot/rootfs"
#define CONFIG_BOOTFILE		"uImage"

#define CONFIG_LOADADDR		800000	/* def location for tftp and bootm */

#define CONFIG_BOOTDELAY	6	/* -1 disables auto-boot */
#undef  CONFIG_BOOTARGS			/* boot command will set bootargs */

#define CONFIG_BAUDRATE	 9600

#define	CONFIG_EXTRA_ENV_SETTINGS					\
	"netdev=eth0\0"							\
	"hostname=vme8349\0"						\
	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
		"nfsroot=${serverip}:${rootpath}\0"			\
	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
	"addip=setenv bootargs ${bootargs} "				\
		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
		":${hostname}:${netdev}:off panic=1\0"			\
	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
	"flash_nfs=run nfsargs addip addtty;"				\
		"bootm ${kernel_addr}\0"				\
	"flash_self=run ramargs addip addtty;"				\
		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"	\
		"bootm\0"						\
	"load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0"		\
	"update=protect off fff00000 fff3ffff; "			\
		"era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
	"upd=run load update\0"						\
	"fdtaddr=780000\0"						\
	"fdtfile=vme8349.dtb\0"						\
	""

#define CONFIG_NFSBOOTCOMMAND						\
	"setenv bootargs root=/dev/nfs rw "				\
		"nfsroot=$serverip:$rootpath "				\
		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
							"$netdev:off "	\
		"console=$consoledev,$baudrate $othbootargs;"		\
	"tftp $loadaddr $bootfile;"					\
	"tftp $fdtaddr $fdtfile;"					\
	"bootm $loadaddr - $fdtaddr"

#define CONFIG_RAMBOOTCOMMAND						\
	"setenv bootargs root=/dev/ram rw "				\
		"console=$consoledev,$baudrate $othbootargs;"		\
	"tftp $ramdiskaddr $ramdiskfile;"				\
	"tftp $loadaddr $bootfile;"					\
	"tftp $fdtaddr $fdtfile;"					\
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_BOOTCOMMAND	"run flash_self"

#ifndef __ASSEMBLY__
int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen,
		     unsigned char *buffer, int len);
#endif

#endif	/* __CONFIG_H */
Commit	Line	Data
c2e49f70 RA	1	/*
	2	* esd vme8349 U-Boot configuration file
	3	* Copyright (c) 2008, 2009 esd gmbh Hannover Germany
	4	*
2ae18241	5	* (C) Copyright 2006-2010
c2e49f70 RA	6	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	7	*
	8	* reinhard.arlt@esd-electronics.de
	9	* Based on the MPC8349EMDS config.
	10	*
3765b3e7	11	* SPDX-License-Identifier: GPL-2.0+
c2e49f70 RA	12	*/
	13
	14	/*
	15	* vme8349 board configuration file.
	16	*/
	17
	18	#ifndef __CONFIG_H
	19	#define __CONFIG_H
	20
fdfaa29e KP	21	#define CONFIG_DISPLAY_BOARDINFO
fdfaa29e KP	22
1dee9be6 RA	23	/*
	24	* Top level Makefile configuration choices
	25	*/
2ae18241	26	#ifdef CONFIG_CADDY2
1dee9be6 RA	27	#define VME_CADDY2
	28	#endif
	29
c2e49f70 RA	30	/*
	31	* High Level Configuration Options
	32	*/
	33	#define CONFIG_E300 1 /* E300 Family */
c2e49f70 RA	34	#define CONFIG_MPC834x 1 /* MPC834x family */
	35	#define CONFIG_MPC8349 1 /* MPC8349 specific */
	36	#define CONFIG_VME8349 1 /* ESD VME8349 board specific */
	37
2ae18241 WD	38	#define CONFIG_SYS_TEXT_BASE 0xFFF00000
2ae18241 WD	39
1dee9be6 RA	40	#define CONFIG_MISC_INIT_R
1dee9be6 RA	41
c2e49f70 RA	42	#define CONFIG_PCI
	43	/* Don't enable PCI2 on vme834x - it doesn't exist physically. */
	44	#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */
	45
2ae18241 WD	46	#define CONFIG_PCI_66M
2ae18241 WD	47	#ifdef CONFIG_PCI_66M
c2e49f70 RA	48	#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
	49	#else
	50	#define CONFIG_83XX_CLKIN 33000000 /* in Hz */
	51	#endif
	52
	53	#ifndef CONFIG_SYS_CLK_FREQ
2ae18241	54	#ifdef CONFIG_PCI_66M
c2e49f70 RA	55	#define CONFIG_SYS_CLK_FREQ 66000000
	56	#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1
	57	#else
	58	#define CONFIG_SYS_CLK_FREQ 33000000
	59	#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1
	60	#endif
	61	#endif
	62
	63	#define CONFIG_SYS_IMMR 0xE0000000
	64
	65	#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
	66	#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */
	67	#define CONFIG_SYS_MEMTEST_END 0x00100000
	68
	69	/*
	70	* DDR Setup
	71	*/
	72	#define CONFIG_DDR_ECC /* only for ECC DDR module */
	73	#define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
1dee9be6 RA	74	#define CONFIG_SPD_EEPROM
	75	#define SPD_EEPROM_ADDRESS 0x54
	76	#define CONFIG_SYS_READ_SPD vme8349_read_spd
c2e49f70 RA	77	#define CONFIG_SYS_83XX_DDR_USES_CS0 /* esd; Fsl board uses CS2/CS3 */
	78
	79	/*
	80	* 32-bit data path mode.
	81	*
	82	* Please note that using this mode for devices with the real density of 64-bit
	83	* effectively reduces the amount of available memory due to the effect of
	84	* wrapping around while translating address to row/columns, for example in the
	85	* 256MB module the upper 128MB get aliased with contents of the lower
	86	* 128MB); normally this define should be used for devices with real 32-bit
	87	* data path.
	88	*/
	89	#undef CONFIG_DDR_32BIT
	90
	91	#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is sys memory*/
	92	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
	93	#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
2fef4020 JH	94	#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \
2fef4020 JH	95	\| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
c2e49f70	96	#define CONFIG_DDR_2T_TIMING
2fef4020 JH	97	#define CONFIG_SYS_DDRCDR (DDRCDR_DHC_EN \
	98	\| DDRCDR_ODT \
	99	\| DDRCDR_Q_DRN)
	100	/* 0x80080001 */
c2e49f70 RA	101
	102	/*
	103	* FLASH on the Local Bus
	104	*/
	105	#define CONFIG_SYS_FLASH_CFI
	106	#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
1dee9be6 RA	107	#ifdef VME_CADDY2
	108	#define CONFIG_SYS_FLASH_BASE 0xffc00000 /* start of FLASH */
	109	#define CONFIG_SYS_FLASH_SIZE 4 /* flash size in MB */
	110	#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \| \
7d6a0982 JH	111	BR_PS_16 \| /* 16bit */ \
	112	BR_MS_GPCM \| /* MSEL = GPCM */ \
	113	BR_V) /* valid */
	114
	115	#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
	116	\| OR_GPCM_XAM \
	117	\| OR_GPCM_CSNT \
	118	\| OR_GPCM_ACS_DIV2 \
	119	\| OR_GPCM_XACS \
	120	\| OR_GPCM_SCY_15 \
	121	\| OR_GPCM_TRLX_SET \
	122	\| OR_GPCM_EHTR_SET \
	123	\| OR_GPCM_EAD)
	124	/* 0xffc06ff7 */
1dee9be6	125	#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
7d6a0982	126	#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN \| LBLAWAR_4MB)
1dee9be6 RA	127	#else
	128	#define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */
	129	#define CONFIG_SYS_FLASH_SIZE 128 /* flash size in MB */
c2e49f70	130	#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \| \
7d6a0982 JH	131	BR_PS_16 \| /* 16bit */ \
	132	BR_MS_GPCM \| /* MSEL = GPCM */ \
	133	BR_V) /* valid */
	134
	135	#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
	136	\| OR_GPCM_XAM \
	137	\| OR_GPCM_CSNT \
	138	\| OR_GPCM_ACS_DIV2 \
	139	\| OR_GPCM_XACS \
	140	\| OR_GPCM_SCY_15 \
	141	\| OR_GPCM_TRLX_SET \
	142	\| OR_GPCM_EHTR_SET \
	143	\| OR_GPCM_EAD)
	144	/* 0xf8006ff7 */
c2e49f70	145	#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
7d6a0982	146	#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN \| LBLAWAR_128MB)
1dee9be6 RA	147	#endif
1dee9be6 RA	148	/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
c2e49f70	149
7d6a0982 JH	150	#define CONFIG_SYS_WINDOW1_BASE 0xf0000000
	151	#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_WINDOW1_BASE \
	152	\| BR_PS_32 \
	153	\| BR_MS_GPCM \
	154	\| BR_V)
	155	/* 0xF0001801 */
	156	#define CONFIG_SYS_OR1_PRELIM (OR_AM_256KB \
	157	\| OR_GPCM_SETA)
	158	/* 0xfffc0208 */
	159	#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_WINDOW1_BASE
	160	#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN \| LBLAWAR_256KB)
c2e49f70 RA	161
	162	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	163	#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device*/
	164
	165	#undef CONFIG_SYS_FLASH_CHECKSUM
	166	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase TO (ms) */
	167	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write TO (ms) */
	168
c7357a2b	169	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
c2e49f70 RA	170
	171	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	172	#define CONFIG_SYS_RAMBOOT
	173	#else
1dee9be6	174	#undef CONFIG_SYS_RAMBOOT
c2e49f70 RA	175	#endif
	176
	177	#define CONFIG_SYS_INIT_RAM_LOCK 1
	178	#define CONFIG_SYS_INIT_RAM_ADDR 0xF7000000 /* Initial RAM addr */
553f0982	179	#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* size */
c2e49f70	180
553f0982	181	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
25ddd1fb	182	GENERATED_GBL_DATA_SIZE)
c2e49f70 RA	183	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
	184
	185	#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB */
c8a90646	186	#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Malloc size */
c2e49f70 RA	187
	188	/*
	189	* Local Bus LCRR and LBCR regs
1dee9be6	190	* LCRR: no DLL bypass, Clock divider is 4
c2e49f70 RA	191	* External Local Bus rate is
	192	* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
	193	*/
c7190f02	194	#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
c2e49f70 RA	195	#define CONFIG_SYS_LBC_LBCR 0x00000000
	196
	197	#undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */
	198
	199	/*
	200	* Serial Port
	201	*/
	202	#define CONFIG_CONS_INDEX 1
c2e49f70 RA	203	#define CONFIG_SYS_NS16550_SERIAL
	204	#define CONFIG_SYS_NS16550_REG_SIZE 1
	205	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
	206
	207	#define CONFIG_SYS_BAUDRATE_TABLE \
c7357a2b	208	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
c2e49f70 RA	209
	210	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
	211	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
	212
	213	#define CONFIG_CMDLINE_EDITING /* add command line history */
a059e90e	214	#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
c2e49f70	215
c2e49f70	216	/* I2C */
00f792e0 HS	217	#define CONFIG_SYS_I2C
	218	#define CONFIG_SYS_I2C_FSL
	219	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	220	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	221	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	222	#define CONFIG_SYS_FSL_I2C2_SPEED 400000
	223	#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
	224	#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
	225	#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
efaf6f1b	226	/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
c2e49f70 RA	227
	228	#define CONFIG_SYS_I2C_8574_ADDR2 0x20 /* I2C1, PCF8574 */
	229
	230	/* TSEC */
	231	#define CONFIG_SYS_TSEC1_OFFSET 0x24000
	232	#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
	233	#define CONFIG_SYS_TSEC2_OFFSET 0x25000
	234	#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)
	235
	236	/*
	237	* General PCI
	238	* Addresses are mapped 1-1.
	239	*/
	240	#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
	241	#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
	242	#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
	243	#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
	244	#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
	245	#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
	246	#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
	247	#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
	248	#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
	249
	250	#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000
	251	#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
	252	#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */
	253	#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000
	254	#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE
	255	#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */
	256	#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
	257	#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000
	258	#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
	259
	260	#if defined(CONFIG_PCI)
	261
	262	#define PCI_64BIT
	263	#define PCI_ONE_PCI1
	264	#if defined(PCI_64BIT)
	265	#undef PCI_ALL_PCI1
	266	#undef PCI_TWO_PCI1
	267	#undef PCI_ONE_PCI1
	268	#endif
	269
1dee9be6	270	#ifndef VME_CADDY2
1dee9be6 RA	271	#endif
1dee9be6 RA	272	#define CONFIG_PCI_PNP /* do pci plug-and-play */
c2e49f70 RA	273
	274	#undef CONFIG_EEPRO100
	275	#undef CONFIG_TULIP
	276
	277	#if !defined(CONFIG_PCI_PNP)
	278	#define PCI_ENET0_IOADDR 0xFIXME
	279	#define PCI_ENET0_MEMADDR 0xFIXME
	280	#define PCI_IDSEL_NUMBER 0xFIXME
	281	#endif
	282
1dee9be6 RA	283	#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
	284	#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
	285
c2e49f70 RA	286	#endif /* CONFIG_PCI */
	287
	288	/*
	289	* TSEC configuration
	290	*/
1dee9be6	291	#ifdef VME_CADDY2
1dee9be6	292	#else
c2e49f70	293	#define CONFIG_TSEC_ENET /* TSEC ethernet support */
1dee9be6	294	#endif
c2e49f70 RA	295
c2e49f70 RA	296	#if defined(CONFIG_TSEC_ENET)
c2e49f70	297
1dee9be6	298	#define CONFIG_GMII /* MII PHY management */
c2e49f70 RA	299	#define CONFIG_TSEC1
	300	#define CONFIG_TSEC1_NAME "TSEC0"
	301	#define CONFIG_TSEC2
	302	#define CONFIG_TSEC2_NAME "TSEC1"
	303	#define CONFIG_PHY_M88E1111
	304	#define TSEC1_PHY_ADDR 0x08
	305	#define TSEC2_PHY_ADDR 0x10
	306	#define TSEC1_PHYIDX 0
	307	#define TSEC2_PHYIDX 0
	308	#define TSEC1_FLAGS TSEC_GIGABIT
	309	#define TSEC2_FLAGS TSEC_GIGABIT
	310
	311	/* Options are: TSEC[0-1] */
	312	#define CONFIG_ETHPRIME "TSEC0"
	313
	314	#endif /* CONFIG_TSEC_ENET */
	315
	316	/*
	317	* Environment
	318	*/
	319	#ifndef CONFIG_SYS_RAMBOOT
	320	#define CONFIG_ENV_IS_IN_FLASH
	321	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0xc0000)
	322	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
	323	#define CONFIG_ENV_SIZE 0x2000
	324
	325	/* Address and size of Redundant Environment Sector */
	326	#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
	327	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
	328
	329	#else
	330	#define CONFIG_SYS_NO_FLASH /* Flash is not usable now */
	331	#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
	332	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
	333	#define CONFIG_ENV_SIZE 0x2000
	334	#endif
	335
	336	#define CONFIG_LOADS_ECHO /* echo on for serial download */
	337	#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
	338
	339	/*
	340	* BOOTP options
	341	*/
	342	#define CONFIG_BOOTP_BOOTFILESIZE
	343	#define CONFIG_BOOTP_BOOTPATH
	344	#define CONFIG_BOOTP_GATEWAY
	345	#define CONFIG_BOOTP_HOSTNAME
	346
	347	/*
	348	* Command line configuration.
	349	*/
c2e49f70 RA	350	#define CONFIG_CMD_I2C
	351	#define CONFIG_CMD_MII
	352	#define CONFIG_CMD_PING
	353	#define CONFIG_CMD_DATE
	354	#define CONFIG_SYS_RTC_BUS_NUM 0x01
	355	#define CONFIG_SYS_I2C_RTC_ADDR 0x32
	356	#define CONFIG_RTC_RX8025
	357	#define CONFIG_CMD_TSI148
	358
	359	#if defined(CONFIG_PCI)
	360	#define CONFIG_CMD_PCI
	361	#endif
	362
	363	#if defined(CONFIG_SYS_RAMBOOT)
	364	#undef CONFIG_CMD_ENV
c2e49f70 RA	365	#endif
c2e49f70 RA	366
c2e49f70 RA	367	/* Pass Ethernet MAC to VxWorks */
	368	#define CONFIG_SYS_VXWORKS_MAC_PTR 0x000043f0
	369
	370	#undef CONFIG_WATCHDOG /* watchdog disabled */
	371
	372	/*
	373	* Miscellaneous configurable options
	374	*/
	375	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	376	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
c2e49f70 RA	377
	378	#if defined(CONFIG_CMD_KGDB)
	379	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	380	#else
	381	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	382	#endif
	383
	384	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
	385	#define CONFIG_SYS_MAXARGS 16 /* max num of command args */
	386	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buf Size */
c2e49f70 RA	387
	388	/*
	389	* For booting Linux, the board info and command line data
9f530d59	390	* have to be in the first 256 MB of memory, since this is
c2e49f70 RA	391	* the maximum mapped by the Linux kernel during initialization.
c2e49f70 RA	392	*/
9f530d59	393	#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Init Memory map for Linux*/
c2e49f70 RA	394
	395	#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
	396
	397	#define CONFIG_SYS_HRCW_LOW (\
	398	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \|\
	399	HRCWL_DDR_TO_SCB_CLK_1X1 \|\
	400	HRCWL_CSB_TO_CLKIN \|\
	401	HRCWL_VCO_1X2 \|\
	402	HRCWL_CORE_TO_CSB_2X1)
	403
	404	#if defined(PCI_64BIT)
	405	#define CONFIG_SYS_HRCW_HIGH (\
	406	HRCWH_PCI_HOST \|\
	407	HRCWH_64_BIT_PCI \|\
	408	HRCWH_PCI1_ARBITER_ENABLE \|\
	409	HRCWH_PCI2_ARBITER_DISABLE \|\
	410	HRCWH_CORE_ENABLE \|\
	411	HRCWH_FROM_0X00000100 \|\
	412	HRCWH_BOOTSEQ_DISABLE \|\
	413	HRCWH_SW_WATCHDOG_DISABLE \|\
	414	HRCWH_ROM_LOC_LOCAL_16BIT \|\
	415	HRCWH_TSEC1M_IN_GMII \|\
	416	HRCWH_TSEC2M_IN_GMII)
	417	#else
	418	#define CONFIG_SYS_HRCW_HIGH (\
	419	HRCWH_PCI_HOST \|\
	420	HRCWH_32_BIT_PCI \|\
	421	HRCWH_PCI1_ARBITER_ENABLE \|\
	422	HRCWH_PCI2_ARBITER_ENABLE \|\
	423	HRCWH_CORE_ENABLE \|\
	424	HRCWH_FROM_0X00000100 \|\
	425	HRCWH_BOOTSEQ_DISABLE \|\
	426	HRCWH_SW_WATCHDOG_DISABLE \|\
	427	HRCWH_ROM_LOC_LOCAL_16BIT \|\
	428	HRCWH_TSEC1M_IN_GMII \|\
	429	HRCWH_TSEC2M_IN_GMII)
	430	#endif
	431
	432	/* System IO Config */
	433	#define CONFIG_SYS_SICRH 0
	434	#define CONFIG_SYS_SICRL SICRL_LDP_A
	435
	436	#define CONFIG_SYS_HID0_INIT 0x000000000
1a2e203b KP	437	#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \| \
1a2e203b KP	438	HID0_ENABLE_INSTRUCTION_CACHE)
c2e49f70 RA	439
	440	#define CONFIG_SYS_HID2 HID2_HBE
	441
	442	#define CONFIG_SYS_GPIO1_PRELIM
	443	#define CONFIG_SYS_GPIO1_DIR 0x00100000
	444	#define CONFIG_SYS_GPIO1_DAT 0x00100000
	445
	446	#define CONFIG_SYS_GPIO2_PRELIM
	447	#define CONFIG_SYS_GPIO2_DIR 0x78900000
	448	#define CONFIG_SYS_GPIO2_DAT 0x70100000
	449
	450	#define CONFIG_HIGH_BATS /* High BATs supported */
	451
	452	/* DDR @ 0x00000000 */
72cd4087	453	#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \| BATL_PP_RW \| \
c2e49f70 RA	454	BATL_MEMCOHERENCE)
	455	#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \| BATU_BL_256M \| \
	456	BATU_VS \| BATU_VP)
	457
	458	/* PCI @ 0x80000000 */
	459	#ifdef CONFIG_PCI
842033e6	460	#define CONFIG_PCI_INDIRECT_BRIDGE
72cd4087	461	#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \| BATL_PP_RW \| \
c2e49f70 RA	462	BATL_MEMCOHERENCE)
	463	#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \| BATU_BL_256M \| \
	464	BATU_VS \| BATU_VP)
72cd4087	465	#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \| BATL_PP_RW \| \
c2e49f70 RA	466	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	467	#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \| BATU_BL_256M \| \
	468	BATU_VS \| BATU_VP)
	469	#else
	470	#define CONFIG_SYS_IBAT1L (0)
	471	#define CONFIG_SYS_IBAT1U (0)
	472	#define CONFIG_SYS_IBAT2L (0)
	473	#define CONFIG_SYS_IBAT2U (0)
	474	#endif
	475
	476	#ifdef CONFIG_MPC83XX_PCI2
72cd4087	477	#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE \| BATL_PP_RW \| \
c2e49f70 RA	478	BATL_MEMCOHERENCE)
	479	#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE \| BATU_BL_256M \| \
	480	BATU_VS \| BATU_VP)
72cd4087	481	#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE \| BATL_PP_RW \| \
c2e49f70 RA	482	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	483	#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE \| BATU_BL_256M \| \
	484	BATU_VS \| BATU_VP)
	485	#else
	486	#define CONFIG_SYS_IBAT3L (0)
	487	#define CONFIG_SYS_IBAT3U (0)
	488	#define CONFIG_SYS_IBAT4L (0)
	489	#define CONFIG_SYS_IBAT4U (0)
	490	#endif
	491
	492	/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
72cd4087	493	#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \| BATL_PP_RW \| \
c2e49f70 RA	494	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	495	#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \| BATU_BL_256M \| \
	496	BATU_VS \| BATU_VP)
	497
72cd4087	498	#define CONFIG_SYS_IBAT6L (0xF0000000 \| BATL_PP_RW \| BATL_MEMCOHERENCE)
c2e49f70 RA	499	#define CONFIG_SYS_IBAT6U (0xF0000000 \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	500
	501	#if (CONFIG_SYS_DDR_SIZE == 512)
	502	#define CONFIG_SYS_IBAT7L (CONFIG_SYS_SDRAM_BASE+0x10000000 \| \
72cd4087	503	BATL_PP_RW \| BATL_MEMCOHERENCE)
c2e49f70 RA	504	#define CONFIG_SYS_IBAT7U (CONFIG_SYS_SDRAM_BASE+0x10000000 \| \
	505	BATU_BL_256M \| BATU_VS \| BATU_VP)
	506	#else
	507	#define CONFIG_SYS_IBAT7L (0)
	508	#define CONFIG_SYS_IBAT7U (0)
	509	#endif
	510
	511	#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
	512	#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
	513	#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
	514	#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
	515	#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
	516	#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
	517	#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
	518	#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
	519	#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
	520	#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
	521	#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
	522	#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
	523	#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
	524	#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
	525	#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
	526	#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
	527
c2e49f70 RA	528	#if defined(CONFIG_CMD_KGDB)
c2e49f70 RA	529	#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
c2e49f70 RA	530	#endif
	531
	532	/*
	533	* Environment Configuration
	534	*/
	535	#define CONFIG_ENV_OVERWRITE
	536
	537	#if defined(CONFIG_TSEC_ENET)
	538	#define CONFIG_HAS_ETH0
	539	#define CONFIG_HAS_ETH1
	540	#endif
	541
	542	#define CONFIG_HOSTNAME VME8349
8b3637c6	543	#define CONFIG_ROOTPATH "/tftpboot/rootfs"
b3f44c21	544	#define CONFIG_BOOTFILE "uImage"
c2e49f70	545
79f516bc	546	#define CONFIG_LOADADDR 800000 /* def location for tftp and bootm */
c2e49f70 RA	547
	548	#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
	549	#undef CONFIG_BOOTARGS /* boot command will set bootargs */
	550
1dee9be6	551	#define CONFIG_BAUDRATE 9600
c2e49f70 RA	552
	553	#define CONFIG_EXTRA_ENV_SETTINGS \
	554	"netdev=eth0\0" \
	555	"hostname=vme8349\0" \
	556	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	557	"nfsroot=${serverip}:${rootpath}\0" \
	558	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	559	"addip=setenv bootargs ${bootargs} " \
	560	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	561	":${hostname}:${netdev}:off panic=1\0" \
	562	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
	563	"flash_nfs=run nfsargs addip addtty;" \
	564	"bootm ${kernel_addr}\0" \
	565	"flash_self=run ramargs addip addtty;" \
	566	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	567	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
	568	"bootm\0" \
	569	"load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0" \
	570	"update=protect off fff00000 fff3ffff; " \
	571	"era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
	572	"upd=run load update\0" \
79f516bc	573	"fdtaddr=780000\0" \
c2e49f70 RA	574	"fdtfile=vme8349.dtb\0" \
	575	""
	576
c7357a2b JH	577	#define CONFIG_NFSBOOTCOMMAND \
	578	"setenv bootargs root=/dev/nfs rw " \
	579	"nfsroot=$serverip:$rootpath " \
	580	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
	581	"$netdev:off " \
	582	"console=$consoledev,$baudrate $othbootargs;" \
	583	"tftp $loadaddr $bootfile;" \
	584	"tftp $fdtaddr $fdtfile;" \
	585	"bootm $loadaddr - $fdtaddr"
c2e49f70 RA	586
c2e49f70 RA	587	#define CONFIG_RAMBOOTCOMMAND \
c7357a2b JH	588	"setenv bootargs root=/dev/ram rw " \
	589	"console=$consoledev,$baudrate $othbootargs;" \
	590	"tftp $ramdiskaddr $ramdiskfile;" \
	591	"tftp $loadaddr $bootfile;" \
	592	"tftp $fdtaddr $fdtfile;" \
	593	"bootm $loadaddr $ramdiskaddr $fdtaddr"
c2e49f70 RA	594
	595	#define CONFIG_BOOTCOMMAND "run flash_self"
	596
1dee9be6 RA	597	#ifndef __ASSEMBLY__
	598	int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen,
	599	unsigned char *buffer, int len);
	600	#endif
	601
c2e49f70	602	#endif /* __CONFIG_H */