This patch adds support for the PDU001 board.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
source "board/cavium/thunderx/Kconfig"
source "board/cirrus/edb93xx/Kconfig"
source "board/creative/xfi3/Kconfig"
+source "board/eets/pdu001/Kconfig"
source "board/freescale/ls2080a/Kconfig"
source "board/freescale/ls2080aqds/Kconfig"
source "board/freescale/ls2080ardb/Kconfig"
am335x-bonegreen.dtb \
am335x-icev2.dtb \
am335x-pxm50.dtb \
- am335x-rut.dtb
+ am335x-rut.dtb \
+ am335x-pdu001.dtb
dtb-$(CONFIG_AM43XX) += am437x-gp-evm.dtb am437x-sk-evm.dtb \
am43x-epos-evm.dtb \
am437x-idk-evm.dtb
--- /dev/null
+/*
+ * Copyright (C) 2018 EETS GmbH - https://www.eets.ch/
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/ {
+ ocp {
+ u-boot,dm-pre-reloc;
+ };
+};
+
+&l4_wkup {
+ u-boot,dm-pre-reloc;
+};
+
+&scm {
+ u-boot,dm-pre-reloc;
+};
+
+&am33xx_pinmux {
+ u-boot,dm-pre-reloc;
+};
+
+&uart3_pins {
+ u-boot,dm-pre-reloc;
+};
+
+&uart3 {
+ u-boot,dm-pre-reloc;
+};
+
+&mmc1_pins {
+ u-boot,dm-pre-reloc;
+};
+
+&mmc2_pins {
+ u-boot,dm-pre-reloc;
+};
--- /dev/null
+/*
+ * pdu001.dts
+ *
+ * EETS GmbH PDU001 board device tree file
+ *
+ * Copyright (C) 2018 EETS GmbH - http://www.eets.ch/
+ *
+ * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/leds-pca9532.h>
+
+/ {
+ model = "EETS,PDU001";
+ compatible = "eets,pdu001", "ti,am33xx";
+
+ chosen {
+ stdout-path = &uart3;
+ };
+
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&vdd1_reg>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ vbat: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vbat";
+ regulator-min-microvolt = <3600000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-boot-on;
+ };
+
+ lis3_reg: fixedregulator@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "lis3_reg";
+ regulator-boot-on;
+ };
+
+ panel {
+ compatible = "ti,tilcdc,panel";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_pins_s0>;
+ panel-info {
+ ac-bias = <255>;
+ ac-bias-intrpt = <0>;
+ dma-burst-sz = <16>;
+ bpp = <16>;
+ fdd = <0x80>;
+ sync-edge = <0>;
+ sync-ctrl = <1>;
+ raster-order = <0>;
+ fifo-th = <0>;
+ };
+
+ display-timings {
+ 240x320p16 {
+ clock-frequency = <6500000>;
+ hactive = <240>;
+ vactive = <320>;
+ hfront-porch = <6>;
+ hback-porch = <6>;
+ hsync-len = <1>;
+ vback-porch = <6>;
+ vfront-porch = <6>;
+ vsync-len = <1>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ pixelclk-active = <1>;
+ de-active = <0>;
+ };
+ };
+ };
+};
+
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&clkout2_pin>;
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */
+ AM33XX_IOPAD(0x95c, PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_cs0.i2c1_scl */
+ >;
+ };
+
+ i2c2_pins: pinmux_i2c2_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x950, PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_clk.i2c2_sda */
+ AM33XX_IOPAD(0x954, PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d0.i2c2_scl */
+ >;
+ };
+
+ spi1_pins: pinmux_spi1_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x990, PIN_OUTPUT | MUX_MODE3) /* mcasp0_aclkx.spi1_sclk */
+ AM33XX_IOPAD(0x994, PIN_OUTPUT | MUX_MODE3) /* mcasp0_fsx.spi1_d0 */
+ AM33XX_IOPAD(0x998, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcasp0_axr0.spi1_d1 */
+ AM33XX_IOPAD(0x99C, PIN_OUTPUT | MUX_MODE3) /* mcasp0_ahclkr.spi1_cs0 */
+ >;
+ };
+
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x96C, PIN_OUTPUT | MUX_MODE7) /* uart0_rtsn.gpio1_9 */
+ AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ uart1_pins: pinmux_uart1_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */
+ AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP | MUX_MODE1) /* spi0_cs1.uart3_rxd */
+ AM33XX_IOPAD(0x964, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* ecap0_in_pwm0_out.uart3_txd */
+ >;
+ };
+
+ clkout2_pin: pinmux_clkout2_pin {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x9b4, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
+ >;
+ };
+
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Port 1 (emac0) */
+ AM33XX_IOPAD(0x908, PIN_INPUT | MUX_MODE0) /* mii1_col.mii1_col */
+ AM33XX_IOPAD(0x90C, PIN_INPUT | MUX_MODE0) /* mii1_crs.mii1_crs */
+ AM33XX_IOPAD(0x910, PIN_INPUT | MUX_MODE0) /* mii1_rxer.mii1_rxer */
+ AM33XX_IOPAD(0x914, PIN_OUTPUT | MUX_MODE0) /* mii1_txen.mii1_txen */
+ AM33XX_IOPAD(0x918, PIN_INPUT | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */
+ AM33XX_IOPAD(0x91c, PIN_OUTPUT | MUX_MODE0) /* mii1_txd3.mii1_txd3 */
+ AM33XX_IOPAD(0x920, PIN_OUTPUT | MUX_MODE0) /* mii1_txd2.mii1_txd2 */
+ AM33XX_IOPAD(0x924, PIN_OUTPUT | MUX_MODE0) /* mii1_txd1.mii1_txd1 */
+ AM33XX_IOPAD(0x928, PIN_OUTPUT | MUX_MODE0) /* mii1_txd0.mii1_txd0 */
+ AM33XX_IOPAD(0x92c, PIN_INPUT | MUX_MODE0) /* mii1_txclk.mii1_txclk */
+ AM33XX_IOPAD(0x930, PIN_INPUT | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */
+ AM33XX_IOPAD(0x934, PIN_INPUT | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */
+ AM33XX_IOPAD(0x938, PIN_INPUT | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */
+ AM33XX_IOPAD(0x93c, PIN_INPUT | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */
+ AM33XX_IOPAD(0x940, PIN_INPUT | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */
+
+ /* Port 2 (emac1) */
+ AM33XX_IOPAD(0x840, PIN_OUTPUT | MUX_MODE1) /* mii2_txen.gpmc_a0 */
+ AM33XX_IOPAD(0x844, PIN_INPUT | MUX_MODE1) /* mii2_rxdv.gpmc_a1 */
+ AM33XX_IOPAD(0x848, PIN_OUTPUT | MUX_MODE1) /* mii2_txd3.gpmc_a2 */
+ AM33XX_IOPAD(0x84c, PIN_OUTPUT | MUX_MODE1) /* mii2_txd2.gpmc_a3 */
+ AM33XX_IOPAD(0x850, PIN_OUTPUT | MUX_MODE1) /* mii2_txd1.gpmc_a4 */
+ AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE1) /* mii2_txd0.gpmc_a5 */
+ AM33XX_IOPAD(0x858, PIN_INPUT | MUX_MODE1) /* mii2_txclk.gpmc_a6 */
+ AM33XX_IOPAD(0x85c, PIN_INPUT | MUX_MODE1) /* mii2_rxclk.gpmc_a7 */
+ AM33XX_IOPAD(0x860, PIN_INPUT | MUX_MODE1) /* mii2_rxd3.gpmc_a8 */
+ AM33XX_IOPAD(0x864, PIN_INPUT | MUX_MODE1) /* mii2_rxd2.gpmc_a9 */
+ AM33XX_IOPAD(0x868, PIN_INPUT | MUX_MODE1) /* mii2_rxd1.gpmc_a10 */
+ AM33XX_IOPAD(0x86C, PIN_INPUT | MUX_MODE1) /* mii2_rxd0.gpmc_a11 */
+ AM33XX_IOPAD(0x870, PIN_INPUT | MUX_MODE1) /* mii2_crs.gpmc_wait0 */
+ AM33XX_IOPAD(0x874, PIN_INPUT | MUX_MODE1) /* mii2_rxer.gpmc_wpn */
+ AM33XX_IOPAD(0x878, PIN_INPUT | MUX_MODE1) /* mii2_col.gpmc_ben1 */
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ mmc1_pins: pinmux_mmc1_pins {
+ /* eMMC */
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3 */
+ AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2 */
+ AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1 */
+ AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0 */
+ AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk */
+ AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd */
+ >;
+ };
+
+ mmc2_pins: pinmux_mmc2_pins {
+ /* SD cardcage */
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+ AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+ AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+ AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+ AM33XX_IOPAD(0x880, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+ AM33XX_IOPAD(0x884, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+ /* card change signal for frontpanel SD cardcage */
+ AM33XX_IOPAD(0x890, PIN_INPUT | MUX_MODE7) /* gpmc_advn_ale.gpio2_2 */
+ >;
+ };
+
+ lcd_pins_s0: lcd_pins_s0 {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */
+ AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */
+ AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */
+ AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */
+ AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */
+ AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */
+ AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */
+ AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */
+ AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */
+ AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */
+ AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */
+ AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */
+ AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */
+ AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */
+ AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */
+ AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */
+ AM33XX_IOPAD(0x8e0, PIN_OUTPUT | MUX_MODE0) /* lcd_vsync.lcd_vsync */
+ AM33XX_IOPAD(0x8e4, PIN_OUTPUT | MUX_MODE0) /* lcd_hsync.lcd_hsync */
+ AM33XX_IOPAD(0x8e8, PIN_OUTPUT | MUX_MODE0) /* lcd_pclk.lcd_pclk */
+ AM33XX_IOPAD(0x8ec, PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */
+ >;
+ };
+
+ dcan0_pins: pinmux_dcan0_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x978, PIN_OUTPUT | MUX_MODE2) /* uart1_ctsn.d_can0_tx */
+ AM33XX_IOPAD(0x97c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* uart1_rtsn.d_can0_rx */
+ >;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+
+ rts-gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ rs485-rts-active-high;
+ rs485-rts-delay = <0 0>;
+ linux,rs485-enabled-at-boot-time;
+
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps@2d {
+ reg = <0x2d>;
+ };
+
+ m2_eeprom: m2_eeprom@50 {
+ compatible = "atmel,24c256";
+ reg = <0x50>;
+ status = "okay";
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ status = "okay";
+ clock-frequency = <100000>;
+
+ board_24aa025e48: board_24aa025e48@50 {
+ compatible = "microchip,24aa025e48";
+ reg = <0x50>;
+ };
+
+ backplane_24aa025e48: backplane_24aa025e48@53 {
+ compatible = "microchip,24aa025e48";
+ reg = <0x53>;
+ };
+
+ pca9532: pca9532@60 {
+ compatible = "nxp,pca9532";
+ reg = <0x60>;
+ psc0 = <0x97>;
+ pwm0 = <0x80>;
+ psc1 = <0x97>;
+ pwm1 = <0x10>;
+
+ run.red@0 {
+ type = <PCA9532_TYPE_LED>;
+ };
+ run.green@1 {
+ type = <PCA9532_TYPE_LED>;
+ default-state = "on";
+ };
+ s2.red@2 {
+ type = <PCA9532_TYPE_LED>;
+ };
+ s2.green@3 {
+ type = <PCA9532_TYPE_LED>;
+ };
+ s1.yellow@4 {
+ type = <PCA9532_TYPE_LED>;
+ };
+ s1.green@5 {
+ type = <PCA9532_TYPE_LED>;
+ };
+ };
+
+ pca9530: pca9530@61 {
+ compatible = "nxp,pca9530";
+ reg = <0x61>;
+
+ tft-panel@0 {
+ type = <PCA9532_TYPE_LED>;
+ linux,default-trigger = "backlight";
+ default-state = "on";
+ };
+ };
+
+ mcp79400: mcp79400@6f {
+ compatible = "microchip,mcp7940x";
+ reg = <0x6f>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+
+ status = "okay";
+ clock-frequency = <100000>;
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>;
+ ti,pindir-d0-out-d1-in;
+ status = "okay";
+
+ cfaf240320a032t {
+ compatible = "orise,otm3225a";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ // SPI mode 3
+ spi-cpol;
+ spi-cpha;
+ status = "okay";
+ };
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb_ctrl_mod {
+ status = "okay";
+};
+
+&usb0_phy {
+ status = "okay";
+};
+
+&usb1_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
+&cppi41dma {
+ status = "okay";
+};
+
+/*
+ * Disable soc's rtc as we have no VBAT for it. This makes the board
+ * rtc (Microchip MCP79400) the default rtc device 'rtc0'.
+ */
+&rtc {
+ status = "disabled";
+};
+
+&lcdc {
+ status = "okay";
+};
+
+&elm {
+ status = "okay";
+};
+
+#include "tps65910.dtsi"
+
+&tps {
+ vcc1-supply = <&vbat>;
+ vcc2-supply = <&vbat>;
+ vcc3-supply = <&vbat>;
+ vcc4-supply = <&vbat>;
+ vcc5-supply = <&vbat>;
+ vcc6-supply = <&vbat>;
+ vcc7-supply = <&vbat>;
+ vccio-supply = <&vbat>;
+
+ regulators {
+ vrtc_reg: regulator@0 {
+ regulator-name = "ldo_vrtc";
+ regulator-always-on;
+ };
+
+ vio_reg: regulator@1 {
+ regulator-name = "buck_vdd_ddr";
+ regulator-always-on;
+ };
+
+ vdd1_reg: regulator@2 {
+ /* VDD_MPU voltage limits */
+ regulator-name = "buck_vdd_mpu";
+ regulator-min-microvolt = <912500>;
+ regulator-max-microvolt = <1312500>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd2_reg: regulator@3 {
+ /* VDD_CORE voltage limits */
+ regulator-name = "buck_vdd_core";
+ regulator-min-microvolt = <912500>;
+ regulator-max-microvolt = <1150000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd3_reg: regulator@4 {
+ regulator-name = "boost_res";
+ regulator-always-on;
+ };
+
+ vdig1_reg: regulator@5 {
+ regulator-name = "ldo_vdig1";
+ regulator-always-on;
+ };
+
+ vdig2_reg: regulator@6 {
+ regulator-name = "ldo_vdig2";
+ regulator-always-on;
+ };
+
+ vpll_reg: regulator@7 {
+ regulator-name = "ldo_vpll";
+ regulator-always-on;
+ };
+
+ vdac_reg: regulator@8 {
+ regulator-name = "ldo_vdac";
+ regulator-always-on;
+ };
+
+ vaux1_reg: regulator@9 {
+ regulator-name = "ldo_vaux1";
+ regulator-always-on;
+ };
+
+ vaux2_reg: regulator@10 {
+ regulator-name = "ldo_vaux2";
+ regulator-always-on;
+ };
+
+ vaux33_reg: regulator@11 {
+ regulator-name = "ldo_vaux33";
+ regulator-always-on;
+ };
+
+ vmmc_reg: regulator@12 {
+ regulator-name = "ldo_vmmc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vbb_reg: regulator@13 {
+ regulator-name = "bat_vbb";
+ };
+ };
+};
+
+&mac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cpsw_default>;
+ dual_emac; /* no switch, two distinct MACs */
+ status = "okay";
+};
+
+&davinci_mdio {
+ pinctrl-names = "default";
+ pinctrl-0 = <&davinci_mdio_default>;
+ status = "okay";
+};
+
+&cpsw_emac0 {
+ phy_id = <&davinci_mdio>, <0>;
+ phy-mode = "mii";
+ dual_emac_res_vlan = <1>;
+};
+
+&cpsw_emac1 {
+ phy_id = <&davinci_mdio>, <1>;
+ phy-mode = "mii";
+ dual_emac_res_vlan = <2>;
+};
+
+&tscadc {
+ status = "okay";
+ tsc {
+ ti,wires = <4>;
+ ti,x-plate-resistance = <200>;
+ ti,coordinate-readouts = <5>;
+ ti,wire-config = <0x01 0x10 0x22 0x33>;
+ ti,charge-delay = <0x400>;
+ };
+
+ adc {
+ ti,adc-channels = <4 5 6 7>;
+ };
+};
+
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&vmmc_reg>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ non-removable;
+};
+
+&mmc2 {
+ status = "okay";
+ vmmc-supply = <&vmmc_reg>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+};
+
+&sham {
+ status = "okay";
+};
+
+&aes {
+ status = "okay";
+};
+
+&dcan0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dcan0_pins>;
+};
select DM_SERIAL
select DM_GPIO
+config TARGET_PDU001
+ bool "Support PDU001"
+ select DM
+ select DM_SERIAL
+ help
+ Support for PDU001 platform developed by EETS GmbH.
+ The PDU001 is a processor and display unit developed around
+ the Computing-Module m2 from bytes at work AG.
+
endchoice
endif
--- /dev/null
+# Copyright (C) 2018 EETS GmbH - http://www.eets.ch/
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+if TARGET_PDU001
+
+config SYS_BOARD
+ default "pdu001"
+
+config SYS_VENDOR
+ default "eets"
+
+config SYS_SOC
+ default "am33xx"
+
+config SYS_CONFIG_NAME
+ default "pdu001"
+
+config CONS_INDEX
+ int "UART used for console"
+ range 1 6
+ default 4
+ help
+ The AM335x SoC has a total of 6 UARTs (UART0 to UART5 as referenced
+ in documentation, etc) available to it. The best choice for the
+ PDU001 is UART3 as it is wired to the header K2; enter 4 here to
+ use UART3. UART0 is connected to the EIA-485 transceiver. If you
+ really need to use it, you are advised to remove the transceiver U14
+ from the board. UART1 is wired to the backplane and therefore
+ accessible from there or by the backplane connector K1 of the PDU.
+ Any other UART then UART3 (enter 4 here), UART1 (enter 2 here) or
+ UART0 (enter 1 here) are not sensible since they are not wired to
+ any connector and therefore difficult to access.
+
+choice
+ prompt "State of Run LED"
+ default PDU001_RUN_LED_RED
+ help
+ The PDU001 has a bi-color (red/green) LED labeled 'Run' which
+ can be used to indicate the operating state of the board. By
+ default it will be lit red by U-Boot. Later in the start-up
+ process it can be changed to green (or heartbeat or anything else)
+ by the kernel or some other software.
+
+config RUN_LED_RED
+ bool
+ prompt "Red"
+ help
+ Lit Run LED red.
+
+config RUN_LED_GREEN
+ bool
+ prompt "Green"
+ help
+ Lit Run LED green.
+
+config RUN_LED_OFF
+ bool
+ prompt "Off"
+ help
+ Do not lit Run LED.
+
+endchoice
+
+endif
--- /dev/null
+PDU001 BOARD
+M: Felix Brack <fb@ltec.ch>
+S: Maintained
+F: board/eets/pdu001/
+F: include/configs/pdu001.h
+F: configs/am335x_pdu001_defconfig
--- /dev/null
+#
+# Makefile
+#
+# Copyright (C) 2018 EETS GmbH - http://www.eets.ch/
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+ifeq ($(CONFIG_SKIP_LOWLEVEL_INIT),)
+obj-y := mux.o
+endif
+
+obj-y += board.o
--- /dev/null
+# Copyright (C) 2018 EETS GmbH - http://www.eets.ch/
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+Summary
+=======
+
+This document covers the PDU001 target.
+
+Hardware
+========
+
+The PDU-001 (Processor and Display Unit) is a plugin card for 19" racks. It is
+manufactured by EETS GmbH (https://www.eets.ch). The core of the board is a m2
+SOM from bytes at work (https://www.bytesatwork.ch) which in turn is based on
+AM3352 SOC from TI (http://www.ti.com).
+
+Customization
+=============
+
+As usual the console serial interface is set by CONFIG_CONS_INDEX. Best choice
+is 4 here since UART3 is wired to the connector K2.
+The Run LED on the PDU-001 can be turned on red by setting CONFIG_RUN_LED_RED
+or green by setting CONFIG_RUN_LED_GREEN. Setting CONFIG_RUN_LED_OFF will turn
+off the Run LED.
+
+Booting
+=======
+
+The system boots from either eMMC or SD card cage. It will first try to boot
+from the SD card cage. If this fails (missing or unbootable SD card) it will
+try to boot from the internal eMMC. The root file system is always expected to
+be located in the second partition of the device (eMMC or SD card) that pro-
+vided the boot loader.
--- /dev/null
+/*
+ * board.c
+ *
+ * Board functions for EETS PDU001 board
+ *
+ * Copyright (C) 2018, EETS GmbH, http://www.eets.ch/
+ *
+ * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <i2c.h>
+#include <environment.h>
+#include <watchdog.h>
+#include <debug_uart.h>
+#include <dm/ofnode.h>
+#include <power/pmic.h>
+#include <power/regulator.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include "board.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define I2C_ADDR_NODE_ID 0x50
+#define I2C_REG_NODE_ID_BASE 0xfa
+#define NODE_ID_BYTE_COUNT 6
+
+#define I2C_ADDR_LEDS 0x60
+#define I2C_REG_RUN_LED 0x06
+#define RUN_LED_OFF 0x0
+#define RUN_LED_RED 0x1
+#define RUN_LED_GREEN (0x1 << 2)
+
+#define VDD_MPU_REGULATOR "regulator@2"
+#define VDD_CORE_REGULATOR "regulator@3"
+#define DEFAULT_CORE_VOLTAGE 1137500
+
+/*
+ * boot device save register
+ * -------------------------
+ * The boot device can be quired by 'spl_boot_device()' in
+ * 'am33xx_spl_board_init'. However it can't be saved in the u-boot
+ * environment here. In turn 'spl_boot_device' can't be called in
+ * 'board_late_init' which allows writing to u-boot environment.
+ * To get the boot device from 'am33xx_spl_board_init' to
+ * 'board_late_init' we therefore use a scratch register from the RTC.
+ */
+#define CONFIG_SYS_RTC_SCRATCH0 0x60
+#define BOOT_DEVICE_SAVE_REGISTER (RTC_BASE + CONFIG_SYS_RTC_SCRATCH0)
+
+#ifdef CONFIG_SPL_BUILD
+static void save_boot_device(void)
+{
+ *((u32 *)(BOOT_DEVICE_SAVE_REGISTER)) = spl_boot_device();
+}
+#endif
+
+u32 boot_device(void)
+{
+ return *((u32 *)(BOOT_DEVICE_SAVE_REGISTER));
+}
+
+/* Store the boot device in the environment variable 'boot_device' */
+static void env_set_boot_device(void)
+{
+ switch (boot_device()) {
+ case BOOT_DEVICE_MMC1: {
+ env_set("boot_device", "emmc");
+ break;
+ }
+ case BOOT_DEVICE_MMC2: {
+ env_set("boot_device", "sdcard");
+ break;
+ }
+ default: {
+ env_set("boot_device", "unknown");
+ break;
+ }
+ }
+}
+
+static void set_run_led(struct udevice *dev)
+{
+ int val = RUN_LED_OFF;
+
+ if (IS_ENABLED(CONFIG_RUN_LED_RED))
+ val = RUN_LED_RED;
+ else if (IS_ENABLED(CONFIG_RUN_LED_GREEN))
+ val = RUN_LED_GREEN;
+
+ dm_i2c_reg_write(dev, I2C_REG_RUN_LED, val);
+}
+
+/* Set 'serial#' to the EUI-48 value of board node ID chip */
+static void env_set_serial(struct udevice *dev)
+{
+ int val;
+ char serial[2 * NODE_ID_BYTE_COUNT + 1];
+ int n;
+
+ for (n = 0; n < sizeof(serial); n += 2) {
+ val = dm_i2c_reg_read(dev, I2C_REG_NODE_ID_BASE + n / 2);
+ sprintf(serial + n, "%02X", val);
+ }
+ serial[2 * NODE_ID_BYTE_COUNT] = '\0';
+ env_set("serial#", serial);
+}
+
+static void set_mpu_and_core_voltage(void)
+{
+ int mpu_vdd;
+ int sil_rev;
+ struct udevice *dev;
+ struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+ /*
+ * The PDU001 (more precisely the computing module m2) uses a
+ * TPS65910 PMIC. For all MPU frequencies we support we use a CORE
+ * voltage of 1.1375V. For MPU voltage we need to switch based on
+ * the frequency we are running at.
+ */
+
+ /*
+ * Depending on MPU clock and PG we will need a different VDD
+ * to drive at that speed.
+ */
+ sil_rev = readl(&cdev->deviceid) >> 28;
+ mpu_vdd = am335x_get_mpu_vdd(sil_rev, dpll_mpu_opp100.m);
+
+ /* first update the MPU voltage */
+ if (!regulator_get_by_devname(VDD_MPU_REGULATOR, &dev)) {
+ if (regulator_set_value(dev, mpu_vdd))
+ debug("failed to set MPU voltage\n");
+ } else {
+ debug("invalid MPU voltage ragulator %s\n", VDD_MPU_REGULATOR);
+ }
+
+ /* second update the CORE voltage */
+ if (!regulator_get_by_devname(VDD_CORE_REGULATOR, &dev)) {
+ if (regulator_set_value(dev, DEFAULT_CORE_VOLTAGE))
+ debug("failed to set CORE voltage\n");
+ } else {
+ debug("invalid CORE voltage ragulator %s\n",
+ VDD_CORE_REGULATOR);
+ }
+}
+
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
+static const struct ddr_data ddr2_data = {
+ .datardsratio0 = MT47H128M16RT25E_RD_DQS,
+ .datafwsratio0 = MT47H128M16RT25E_PHY_FIFO_WE,
+ .datawrsratio0 = MT47H128M16RT25E_PHY_WR_DATA,
+};
+
+static const struct cmd_control ddr2_cmd_ctrl_data = {
+ .cmd0csratio = MT47H128M16RT25E_RATIO,
+ .cmd1csratio = MT47H128M16RT25E_RATIO,
+ .cmd2csratio = MT47H128M16RT25E_RATIO,
+};
+
+static const struct emif_regs ddr2_emif_reg_data = {
+ .sdram_config = MT47H128M16RT25E_EMIF_SDCFG,
+ .ref_ctrl = MT47H128M16RT25E_EMIF_SDREF,
+ .sdram_tim1 = MT47H128M16RT25E_EMIF_TIM1,
+ .sdram_tim2 = MT47H128M16RT25E_EMIF_TIM2,
+ .sdram_tim3 = MT47H128M16RT25E_EMIF_TIM3,
+ .emif_ddr_phy_ctlr_1 = MT47H128M16RT25E_EMIF_READ_LATENCY,
+};
+
+#define OSC (V_OSCK / 1000000)
+const struct dpll_params dpll_ddr = {
+ 266, OSC - 1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_evm_sk = {
+ 303, OSC - 1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_bone_black = {
+ 400, OSC - 1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+ struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+ /* Get the frequency */
+ dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
+
+ /* Set CORE Frequencies to OPP100 */
+ do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+ /* Set MPU Frequency to what we detected now that voltages are set */
+ do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+
+ /* save boot device for later use by 'board_late_init' */
+ save_boot_device();
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+ enable_i2c0_pin_mux();
+ i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
+
+ return &dpll_ddr;
+}
+
+void set_mux_conf_regs(void)
+{
+ /* done first by the ROM and afterwards by the pin controller driver */
+ enable_i2c0_pin_mux();
+}
+
+const struct ctrl_ioregs ioregs = {
+ .cm0ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
+ .cm1ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
+ .cm2ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
+ .dt0ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
+ .dt1ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
+};
+
+void sdram_init(void)
+{
+ config_ddr(266, &ioregs, &ddr2_data,
+ &ddr2_cmd_ctrl_data, &ddr2_emif_reg_data, 0);
+}
+#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
+
+#ifdef CONFIG_DEBUG_UART
+void board_debug_uart_init(void)
+{
+ /* done by pin controller driver if not debugging */
+ enable_uart_pin_mux(CONFIG_DEBUG_UART_BASE);
+}
+#endif
+
+/*
+ * Basic board specific setup. Pinmux has been handled already.
+ */
+int board_init(void)
+{
+#ifdef CONFIG_HW_WATCHDOG
+ hw_watchdog_init();
+#endif
+
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+ return 0;
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+ struct udevice *dev;
+
+ set_mpu_and_core_voltage();
+ env_set_boot_device();
+
+ /* second I2C bus connects to node ID and front panel LED chip */
+ if (!i2c_get_chip_for_busnum(1, I2C_ADDR_LEDS, 1, &dev))
+ set_run_led(dev);
+ if (!i2c_get_chip_for_busnum(1, I2C_ADDR_NODE_ID, 1, &dev))
+ env_set_serial(dev);
+
+ return 0;
+}
+#endif
--- /dev/null
+/*
+ * board.h
+ *
+ * EETS GmbH PDU001 board information header
+ *
+ * Copyright (C) 2018 EETS GmbH - http://www.eets.ch/
+ *
+ * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * We have two pin mux functions that must exist. First we need I2C0 to
+ * access the TPS65910 PMIC located on the M2 computing module.
+ * Second, if we want low-level debugging or a early UART (ie. before the
+ * pin controller driver is running), we need one of the UART ports UART0 to
+ * UART5 (usually UART3 since it is wired to K2).
+ * In case of I2C0 access we explicitly don't rely on the the ROM but we could
+ * do so as we use the primary mode (mode 0) for I2C0.
+ * All other multiplexing and pin configuration is done by the DT once it
+ * gets parsed by the pin controller driver.
+ * However we relay on the ROM to configure the pins of MMC0 (eMMC) as well
+ * as MMC1 (microSD card-cage) since these are our boot devices.
+ */
+void enable_uart0_pin_mux(void);
+void enable_uart1_pin_mux(void);
+void enable_uart2_pin_mux(void);
+void enable_uart3_pin_mux(void);
+void enable_uart4_pin_mux(void);
+void enable_uart5_pin_mux(void);
+void enable_uart_pin_mux(u32 addr);
+void enable_i2c0_pin_mux(void);
+
+#endif
--- /dev/null
+/*
+ * mux.c
+ *
+ * Copyright (C) 2018 EETS GmbH - http://www.eets.ch/
+ *
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include <i2c.h>
+#include "board.h"
+
+static struct module_pin_mux uart0_pin_mux[] = {
+ {OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* UART0_RXD */
+ {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)}, /* UART0_TXD */
+ {-1},
+};
+
+static struct module_pin_mux uart1_pin_mux[] = {
+ {OFFSET(uart1_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* UART1_RXD */
+ {OFFSET(uart1_txd), (MODE(0) | PULLUDEN)}, /* UART1_TXD */
+ {-1},
+};
+
+static struct module_pin_mux uart2_pin_mux[] = {
+ {OFFSET(spi0_sclk), (MODE(1) | PULLUP_EN | RXACTIVE)}, /* UART2_RXD */
+ {OFFSET(spi0_d0), (MODE(1) | PULLUDEN)}, /* UART2_TXD */
+ {-1},
+};
+
+static struct module_pin_mux uart3_pin_mux[] = {
+ {OFFSET(spi0_cs1), (MODE(1) | PULLUP_EN | RXACTIVE)}, /* UART3_RXD */
+ {OFFSET(ecap0_in_pwm0_out), (MODE(1) | PULLUDEN)}, /* UART3_TXD */
+ {-1},
+};
+
+static struct module_pin_mux uart4_pin_mux[] = {
+ {OFFSET(gpmc_wait0), (MODE(6) | PULLUP_EN | RXACTIVE)}, /* UART4_RXD */
+ {OFFSET(gpmc_wpn), (MODE(6) | PULLUDEN)}, /* UART4_TXD */
+ {-1},
+};
+
+static struct module_pin_mux uart5_pin_mux[] = {
+ {OFFSET(lcd_data9), (MODE(4) | PULLUP_EN | RXACTIVE)}, /* UART5_RXD */
+ {OFFSET(lcd_data8), (MODE(4) | PULLUDEN)}, /* UART5_TXD */
+ {-1},
+};
+
+static struct module_pin_mux i2c0_pin_mux[] = {
+ {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE |
+ PULLUDEN | SLEWCTRL)}, /* I2C_DATA */
+ {OFFSET(i2c0_scl), (MODE(0) | RXACTIVE |
+ PULLUDEN | SLEWCTRL)}, /* I2C_SCLK */
+ {-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+ configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_uart1_pin_mux(void)
+{
+ configure_module_pin_mux(uart1_pin_mux);
+}
+
+void enable_uart2_pin_mux(void)
+{
+ configure_module_pin_mux(uart2_pin_mux);
+}
+
+void enable_uart3_pin_mux(void)
+{
+ configure_module_pin_mux(uart3_pin_mux);
+}
+
+void enable_uart4_pin_mux(void)
+{
+ configure_module_pin_mux(uart4_pin_mux);
+}
+
+void enable_uart5_pin_mux(void)
+{
+ configure_module_pin_mux(uart5_pin_mux);
+}
+
+void enable_uart_pin_mux(u32 addr)
+{
+ switch (addr) {
+ case CONFIG_SYS_NS16550_COM1:
+ enable_uart0_pin_mux();
+ break;
+ case CONFIG_SYS_NS16550_COM2:
+ enable_uart1_pin_mux();
+ break;
+ case CONFIG_SYS_NS16550_COM3:
+ enable_uart2_pin_mux();
+ break;
+ case CONFIG_SYS_NS16550_COM4:
+ enable_uart3_pin_mux();
+ break;
+ case CONFIG_SYS_NS16550_COM5:
+ enable_uart4_pin_mux();
+ break;
+ case CONFIG_SYS_NS16550_COM6:
+ enable_uart5_pin_mux();
+ break;
+ }
+}
+
+void enable_i2c0_pin_mux(void)
+{
+ configure_module_pin_mux(i2c0_pin_mux);
+}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_OMAP2PLUS=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_AM33XX=y
+CONFIG_TARGET_PDU001=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_LIBDISK_SUPPORT=y
+# CONFIG_SPL_NAND_SUPPORT is not set
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_SPL_FAT_SUPPORT=y
+CONFIG_DEFAULT_DEVICE_TREE="am335x-pdu001"
+CONFIG_LOCALVERSION="-EETS-1.0.0"
+CONFIG_BOOTDELAY=1
+CONFIG_SPL=y
+# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_YMODEM_SUPPORT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
+CONFIG_AUTOBOOT_STOP_STR=" "
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_XIMG is not set
+CONFIG_CMD_MEMINFO=y
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+# CONFIG_CMD_NET is not set
+# CONFIG_CMD_NFS is not set
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_EMBED=y
+CONFIG_SPL_DM=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_MMC_OMAP_HS=y
+CONFIG_MMC_SDHCI=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_SINGLE=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_TPS65910=y
+CONFIG_DM_REGULATOR=y
+CONFIG_SPL_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_TPS65910=y
+CONFIG_SYS_NS16550=y
+# CONFIG_USE_TINY_PRINTF is not set
+# CONFIG_EFI_LOADER is not set
--- /dev/null
+/*
+ * pdu001.h
+ *
+ * Copyright (C) 2018 EETS GmbH - http://www.eets.ch/
+ *
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_PDU001_H
+#define __CONFIG_PDU001_H
+
+#include <configs/ti_am335x_common.h>
+
+/* No more need for I2C legacy compatibility for this board.
+ * CONFIG_DM_I2C_COMPAT is defined in ti_armv7_common.h. See the comment there
+ * for the right moment to delete the following line.
+ */
+#undef CONFIG_DM_I2C_COMPAT
+
+/* Using 32K of volatile storage for environment */
+#define CONFIG_ENV_SIZE 0x4000
+
+#define MACH_TYPE_PDU001 5075
+#define CONFIG_MACH_TYPE MACH_TYPE_PDU001
+#define CONFIG_BOARD_LATE_INIT
+
+/* Clock Defines */
+#define V_OSCK 24000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK)
+
+#if CONFIG_CONS_INDEX == 1
+ #define CONSOLE_DEV "ttyO0"
+#elif CONFIG_CONS_INDEX == 2
+ #define CONSOLE_DEV "ttyO1"
+#elif CONFIG_CONS_INDEX == 3
+ #define CONSOLE_DEV "ttyO2"
+#elif CONFIG_CONS_INDEX == 4
+ #define CONSOLE_DEV "ttyO3"
+#elif CONFIG_CONS_INDEX == 5
+ #define CONSOLE_DEV "ttyO4"
+#elif CONFIG_CONS_INDEX == 6
+ #define CONSOLE_DEV "ttyO5"
+#endif
+
+#define CONFIG_BOOTCOMMAND \
+ "run eval_boot_device;" \
+ "setenv bootargs console=${console} " \
+ "vt.global_cursor_default=0 " \
+ "root=/dev/mmcblk${mmc_boot}p${root_fs_partition} " \
+ "rootfstype=ext4 " \
+ "rootwait " \
+ "rootdelay=1;" \
+ "fatload mmc ${mmc_boot} ${fdtaddr} ${fdtfile};" \
+ "fatload mmc ${mmc_boot} ${loadaddr} ${bootfile};" \
+ "bootz ${loadaddr} - ${fdtaddr}"
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ DEFAULT_LINUX_BOOT_ENV \
+ "fdtfile=am335x-pdu001.dtb\0" \
+ "bootfile=zImage\0" \
+ "console=" CONSOLE_DEV ",115200n8\0" \
+ "root_fs_partition=2\0" \
+ "eval_boot_device=" \
+ "if test $boot_device = emmc; then " \
+ "setenv mmc_boot 0;" \
+ "elif test $boot_device = sdcard; then " \
+ "setenv mmc_boot 1;" \
+ "else " \
+ "echo Bootdevice is neither MMC0 nor MMC1;" \
+ "reset;" \
+ "fi;" \
+ "\0"
+#endif
+
+/* NS16550 Configuration */
+#define CONFIG_SYS_NS16550_COM1 UART0_BASE
+#define CONFIG_SYS_NS16550_COM2 UART1_BASE
+#define CONFIG_SYS_NS16550_COM3 UART2_BASE
+#define CONFIG_SYS_NS16550_COM4 UART3_BASE
+#define CONFIG_SYS_NS16550_COM5 UART4_BASE
+#define CONFIG_SYS_NS16550_COM6 UART5_BASE
+#define CONFIG_BAUDRATE 115200
+
+#endif /* ! __CONFIG_PDU001_H */
projects / people / ms / u-boot.git / commitdiff
