Jaehoon Chung [Fri, 30 Dec 2016 06:30:11 +0000 (15:30 +0900)]
mmc: sdhci: disable the 8bit mode when host doesn't support it
Buswidth is depeneded on Hardware schematic.
Evne though host can support the 8bit buswidth, if hardware doesn't
support 8bit mode, it doesn't work fine.
So the buswidth mode selection leaves a matter in each SoC drivers.
On the contrary to this, hardware supports 8bit mode, but host doesn't
support it. then controller has to disable the MMC_MODE_8BIT.
(Host can check whether 8bit mode is supported or not, since V3.0)
Michal Simek [Mon, 2 Jan 2017 08:40:09 +0000 (09:40 +0100)]
scsi: dm: Unbind all scsi based block devices before new scan
New scan should unbind all block devices not to be listed again.
Without this patch if scsi reset or scan is called new block devices are
created which point to the same id and lun.
For example:
ZynqMP> scsi scan
scsi_scan: if_type=2, devnum=0: sdhci@ff170000.blk, 6, 0
scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 0
scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 1
scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 2
scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 3
scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 4
scanning bus for devices...
Device 0: (1:0) Vendor: ATA Prod.: KINGSTON SVP200S Rev: 501A
Type: Hard Disk
Capacity: 57241.8 MB = 55.9 GB (117231408 x 512)
Reported-by: Ken Ma <make@marvell.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Simon Glass <sjg@chromium.org>
Jagan Teki [Thu, 5 Jan 2017 14:32:50 +0000 (15:32 +0100)]
mx6ullevk: Add missing MAINTAINERS for mx6ull_14x14_evk_plugin_defconfig
Add 'Peng Fan' as MAINTAINERS of configs/mx6ull_14x14_evk_plugin_defconfig
which is missing in below commit
"imx: mx6ull_14x14_evk: add plugin defconfig"
(sha1: b90ebf49bb8f74afe68f696f59a0e24cc79f2031)
Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Jagan Teki <jagan@openedev.com>
Andrew F. Davis [Fri, 6 Jan 2017 22:32:12 +0000 (16:32 -0600)]
am335x: configs: Use ISW_ENTRY_ADDR to set SPL_TEXT_BASE
The SPL load address changes based on boot type in HS devices,
ISW_ENTRY_ADDR is used to set this address for AM43xx based SoCs
for similar reasons. Add this same logic for AM33xx devices.
Also make the default value for ISW_ENTRY_ADDR correct for GP
devices based on SoC, HS devices already pick the correct
value in their defconfig.
Andrew F. Davis [Fri, 6 Jan 2017 22:20:02 +0000 (16:20 -0600)]
arm: mach-omap2: Fix secure file generation
When TI_SECURE_DEV_PKG is not defined we warn that the file '*_HS' was
not generated but generate an unsigned one anyway, first fix this
warning to say that it was generated but not secured.
When the user then exports TI_SECURE_DEV_PKG after getting this warning,
and tries to re-build, 'make' will detect the build artifacts as
unchanged and so assume they do not need to be re-generated. This causes
it to fail to sign the files and it will pack unsigned files into the
final image, even though TI_SECURE_DEV_PKG is now correctly defined and
working.
Fix this by using FORCE on the targets causes them to be re-run even if
the dependent files have not changed.
This then causes another issue. We currently rename the signed dtb files
to overwrite the non-signed ones. We do this so the 'mkimage' tool gives
the packaged dtb sections the correct name. If we do not rename the files
then SPL will not find them during boot.
Fix this by renaming the dtb files by appending _HS to the end of the
filename, after the ".dtb", this causes them to still be named correctly
in the FIT blob.
York Sun [Wed, 28 Dec 2016 16:43:45 +0000 (08:43 -0800)]
ddr: fsl: Merge macro CONFIG_NUM_DDR_CONTROLLERS and CONFIG_SYS_NUM_DDR_CTRLS
These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.
York Sun [Wed, 28 Dec 2016 16:43:44 +0000 (08:43 -0800)]
ddr: fsl: Move macro CONFIG_NUM_DDR_CONTROLLERS to Kconfig
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.
York Sun [Wed, 28 Dec 2016 16:43:42 +0000 (08:43 -0800)]
mmc: move CONFIG_SYS_FSL_ERRATUM_ESDHC* to Kconfig
Add option SYS_FSL_ERRATUM_ESDHC111, SYS_FSL_ERRATUM_ESDHC13,
SYS_FSL_ERRATUM_ESDHC135, SYS_FSL_ERRATUM_ESDHC_A001 to mmc Kconfig.
Move existing macros to related Kconfig.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate bk4r1] Signed-off-by: Tom Rini <trini@konsulko.com>
York Sun [Wed, 28 Dec 2016 16:43:40 +0000 (08:43 -0800)]
fsl_ddr: Move DDR config options to driver Kconfig
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s] Signed-off-by: Tom Rini <trini@konsulko.com>
Vignesh R [Wed, 21 Dec 2016 05:12:33 +0000 (10:42 +0530)]
spi: cadence_qspi_apb: Use 32 bit indirect read transaction when possible
According to Section 11.15.4.9.1 Indirect Read Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface reads until the last word of an indirect transfer
So, make sure that QSPI indirect reads are 32 bit sized except for the
final read. If the rxbuf is unaligned then use bounce buffer, so that
readsl() can be used instead of readsb() to avoid non 32-bit accesses.
[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Jagan Teki <jagan@openedev.com>
Vignesh R [Wed, 21 Dec 2016 05:12:32 +0000 (10:42 +0530)]
spi: cadence_qspi_apb: Use 32 bit indirect write transaction when possible
According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface writes until the last word of an indirect transfer
otherwise indirect writes is known to fails sometimes. So, make sure
that QSPI indirect writes are 32 bit sized except for the last write. If
the txbuf is unaligned then use bounce buffer to avoid data aborts.
So, now that the driver uses bounce_buffer, enable CONFIG_BOUNCE_BUFFER
for all boards that use Cadence QSPI driver.
[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:45 +0000 (11:48 +0000)]
sunxi: A64: enable SPL
Now that the SPL is ready to be compiled in AArch64 and the DRAM
init code is ready, enable SPL support for the A64 SoC and in the
Pine64 defconfig.
For now we keep the boot0 header in the U-Boot proper, as this allows
to still use boot0 as an SPL replacement without hurting the SPL use
case.
We disable FEL support for now by making its compilation conditional
and disabling it for ARM64, as the code isn't ready yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:44 +0000 (11:48 +0000)]
sunxi: DRAM: fix H3 DRAM size display on aarch64
Fix the output of the DRAM size on AArch64 SPLs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Jens Kuske [Mon, 2 Jan 2017 11:48:42 +0000 (11:48 +0000)]
sunxi: A64: use H3 DRAM initialization code for A64 as well
The A64 DRAM controller is very similar to the H3 one,
so the code can be reused with some small changes.
This refactoring does not change the code size for the existing H3 part.
[Andre: rework from #ifdefs to using socid parameters in static
functions, minor fixes, merging in fixes from Jens]
Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Philipp Tomsich [Mon, 2 Jan 2017 11:48:41 +0000 (11:48 +0000)]
sunxi: clocks: Use the correct pattern register for PLL11
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Jens Kuske [Mon, 2 Jan 2017 11:48:40 +0000 (11:48 +0000)]
sunxi: H3: add DRAM controller single bit delay support
So far the DRAM driver for the H3 SoC (and apparently boot0/libdram as
well) only applied coarse delay line settings, with one delay value for
all the data lines in each byte lane and one value for the control lines.
Instead of setting the delays for whole bytes only allow setting it for
each individual bit. Also add support for address/command lane delays.
For the purpose of this patch the rules for the existing coarse settings
were just applied to the new scheme, so the actual register writes don't
change for the H3. Other SoCs will utilize this feature later properly.
With a stock GCC 5.3.0 this increases the dram_sun8i_h3.o code size from
2296 to 2344 Bytes.
[Andre: move delay parameters into macros to ease later sharing, use
defines for numbers of delay registers, extend commit message]
Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Philipp Tomsich [Mon, 2 Jan 2017 11:48:38 +0000 (11:48 +0000)]
sunxi: H3: Rework MBUS priority setup
So far the MBUS priority setup was done by writing "magic" values taken
from a DRAM controller register dump after a boot0 run.
By peeking at the Linux (sic!) MBUS driver [1] from the Allwinner BSP
kernel, we learned more about the actual meaning of those bits.
Add macros and refactor the setup function to make the MBUS setup much
more readable and meaningful.
The actual values used now are a transformation of the values used
before, which are assembled by the new code to result in the same register
writes. So this rework does not change any settings, also the code size
stays the same.
The respective source files in the BSP kernel had a proper GPL header,
so lifting this code and information into U-Boot is legal.
[Andre: provide a convenience macro to fit definitions on one line]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:37 +0000 (11:48 +0000)]
sunxi: provide default DRAM config for sun50i in Kconfig
To avoid enumerating the very same DRAM values in defconfig files
for each and every Allwinner A64 board out there, let's put some sane
default values in the Kconfig file.
Boards with different needs can override them at any time.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:36 +0000 (11:48 +0000)]
sunxi: A64: do an RMR switch if started in AArch32 mode
The Allwinner A64 SoC starts execution in AArch32 mode, and both
the boot ROM and Allwinner's boot0 keep running in this mode.
So U-Boot gets entered in 32-bit, although we want it to run in AArch64.
By using a "magic" instruction, which happens to be an almost-NOP in
AArch64 and a branch in AArch32, we differentiate between being
entered in 64-bit or 32-bit mode.
If in 64-bit mode, we proceed with the branch to reset, but in 32-bit
mode we trigger an RMR write to bring the core into AArch64/EL3 and
re-enter U-Boot at CONFIG_SYS_TEXT_BASE.
This allows a 64-bit U-Boot to be both entered in 32 and 64-bit mode,
so we can use the same start code for the SPL and the U-Boot proper.
We use the existing custom header (boot0.h) functionality, but restrict
the existing boot0 header reservation to the non-SPL build now. A SPL
wouldn't need such header anyway. This allows to have both options
defined and lets us use one for the SPL and the other for U-Boot proper.
Also add arch/arm/mach-sunxi/rmr_switch.S, which contains the original
ARM assembly code and instructions how to re-generate the encoded
version.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:35 +0000 (11:48 +0000)]
sunxi: introduce extra config option for boot0 header
The ENABLE_ARM_SOC_BOOT0_HOOK option is a generic option shared with
other boards. To allow alternative code to be inserted, we create
another, now function specific config symbol on top of it to simplify
later additions. No functional change at this time.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:34 +0000 (11:48 +0000)]
ARM: boot0 hook: remove macro, include whole header file
For prepending some board specific header area to U-Boot images we
were so far including a header file with a macro definition containing
the actual header specification.
This works fine if there are just a few statements and if there is only
one alternative.
However adding more complex code quickly gets messy with this approach,
so let's just drop that intermediate macro and let the #include actually
insert the code directly.
This converts the callers and the callees, but doesn't change anything
at this point.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Steve Rae <steve.rae@raedomain.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:33 +0000 (11:48 +0000)]
armv8: move reset branch into boot hook
The boot0 hook we have so far is applied _after_ the initial branch
to the "reset" entry point. An upcoming change requires even this
branch to be changed, so we apply the hook macro at the earliest
point, and have the branch in the hook file as well.
This is no functional change at this point, just refactoring to simplify
upcoming patches.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:32 +0000 (11:48 +0000)]
armv8: add simple sdelay implementation
The sunxi DRAM setup code needs an sdelay() implementation, which
wasn't defined for armv8 so far.
Shamelessly copy the armv7 version and adjust it to work in AArch64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:31 +0000 (11:48 +0000)]
SPL: make struct spl_image 64-bit safe
Since entry_point and load_addr are addresses, they should be
represented as longs to cover the whole address space and to avoid
warning when compiling the SPL in 64-bit.
Also adjust debug prints to add the 'l' specifier, where needed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:30 +0000 (11:48 +0000)]
move UL() macro from armv8/mmu.h into common.h
The UL() macro is pretty useful in sharing constants between assembly
and C files while still being able to specify a type for C.
Move the macro from an armv8 specific header into a common header file
to be able to use it by arm code (for instance) as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Alexander Graf <agraf@suse.de> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:29 +0000 (11:48 +0000)]
SPL: tiny-printf: ignore "-" modifier
tiny-printf does not know about the "-" modifier, which aligns numbers.
This is used by some SPL code, but as it's purely cosmetical, we just
ignore this modifier here to avoid changing correct printf strings.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:28 +0000 (11:48 +0000)]
SPL: tiny-printf: add "l" modifier
tiny-printf does not know about the "l" modifier so far, which breaks
the crash dump on AArch64, because it uses %lx to print the registers.
Add an easy way of handling longs correctly.
Using a relatively decent compiler (GCC 5.3.0) this does _not_ increase
the code size of tiny-printf.o for 32-bit builds (where long and int
are actually the same), actually it looses three (ARM Thumb2) instructions
from the actual SPL (numbers for orangepi_plus_defconfig):
text data bss dec hex filename
758 0 0 758 2f6 spl/lib/tiny-printf.o before
18839 488 232 19559 4c67 spl/u-boot-spl before
758 0 0 758 2f6 spl/lib/tiny-printf.o after
18833 488 232 19553 4c61 spl/u-boot-spl after
This adds some substantial amount of code to a 64-bit build, though:
(taken after a later commit, which enables the ARM64 SPL build for sunxi)
text data bss dec hex filename
1542 0 0 1542 606 spl/lib/tiny-printf.o before
25830 392 360 26582 67d6 spl/u-boot-spl before
1758 0 0 1758 6de spl/lib/tiny-printf.o after
26040 392 360 26792 68a8 spl/u-boot-spl after
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:27 +0000 (11:48 +0000)]
armv8: add lowlevel_init.S
For boards that call s_init() when the SPL runs, we are expected to
setup an early stack before calling this C function.
Implement the proper AArch64 version of this based on the ARMv7 code.
This allows sunxi boards to setup the basic peripherals even with a
64-bit SPL.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:26 +0000 (11:48 +0000)]
armv8: prevent using THUMB
The predominantely 32-bit ARM targets try to compile the SPL in Thumb
mode to reduce code size.
The 64-bit AArch64 instruction set does not know an alternative, concise
encoding, so the Thumb build option should only be set for 32-bit
targets.
Likewise -marm machine options are only valid for ARMv7 targets.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:25 +0000 (11:48 +0000)]
sun6i: Restrict some register initialization to Allwinner A31 SoC
These days many Allwinner SoCs use clock_sun6i.c, although out of them
only the (original sun6i) A31 has a second MBUS clock register.
Also the requirement for setting up the PRCM PLL_CTLR1 register to provide
the proper voltage seems to be a property of older SoCs only as well.
Restrict the MBUS initialization to this SoC only to avoid writing bogus
values to (undefined) registers in other chips.
I can only verify that the PLL voltage setup is not needed for H3 and
A64, so for now we only spare those two SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Alexander Graf <agraf@suse.de> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Stephen Warren [Fri, 2 Dec 2016 19:26:42 +0000 (12:26 -0700)]
ARM: tegra: allow passing cboot DTB to the kernel
Some users may wish to pass the cboot-supplied DTB to the booted kernel
rather than having U-Boot load the DTB itself. To allow this, expose the
address of the cboot-supplied DTB in environment variable $fdt_addr. At
least when using extlinux.conf, if the user doesn't explicitly specify
which DTB to pass to the kernel, U-Boot passes the DTB referred to by
this variable.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Jagan Teki [Wed, 21 Dec 2016 11:00:29 +0000 (12:00 +0100)]
configs: engicam: Add fitboot env support
Add FIT image booting from MMC device, during MMC bootcmd
u-boot env script look for bootscript, else fit image or else
finally look for legacy image uImage.
Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enabling FIT along with Signature will make bootm to
not-understanding u-boot legacy image formats like uImage, etc.
So this patch enabling legacy image format for backward compatibility.
Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 21 Dec 2016 11:00:23 +0000 (12:00 +0100)]
defconfigs: engicam: Enable MMC commands in nand
For writing Linux or rootfs on to NAND, the best suitable way
is to use MMC commands since MMC driver by default enabled by
mx6_common.h, hence enabled MMC commands in nand defconfigs.
Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 21 Dec 2016 11:00:22 +0000 (12:00 +0100)]
configs: engicam: Rename nand with gpmi-name in mtdparts
gpmi-nand is the proper name used in nand driver from Linux for all
imx related nand boards, so rename mtdparts name as gpmi-nand instead
of nand, this will eventually reflects all nand info to Linux from
u-boot like mtdparts.
Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
projects / people / ms / u-boot.git / log
