Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
drivers/power/battery/
LIBS-y += drivers/spi/
LIBS-$(CONFIG_FMAN_ENET) += drivers/net/fm/
+LIBS-$(CONFIG_SYS_FSL_DDR) += drivers/ddr/fsl/
LIBS-y += drivers/serial/
LIBS-y += drivers/usb/eth/
LIBS-y += drivers/usb/gadget/
CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
This value denotes start offset of DSP CCSR space.
- CONFIG_SYS_FSL_DDR_EMU
- Specify emulator support for DDR. Some DDR features such as
- deskew training are not available.
-
- Generic CPU options:
CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
Defines the endianess of the CPU. Implementation of those
values is arch specific.
+ CONFIG_SYS_FSL_DDR
+ Freescale DDR driver in use. This type of DDR controller is
+ found in mpc83xx, mpc85xx, mpc86xx as well as some ARM core
+ SoCs.
+
+ CONFIG_SYS_FSL_DDR_ADDR
+ Freescale DDR memory-mapped register base.
+
+ CONFIG_SYS_FSL_DDR_EMU
+ Specify emulator support for DDR. Some DDR features such as
+ deskew training are not available.
+
+ CONFIG_SYS_FSL_DDRC_GEN1
+ Freescale DDR1 controller.
+
+ CONFIG_SYS_FSL_DDRC_GEN2
+ Freescale DDR2 controller.
+
+ CONFIG_SYS_FSL_DDRC_GEN3
+ Freescale DDR3 controller.
+
+ CONFIG_SYS_FSL_DDR1
+ Board config to use DDR1. It can be enabled for SoCs with
+ Freescale DDR1 or DDR2 controllers, depending on the board
+ implemetation.
+
+ CONFIG_SYS_FSL_DDR2
+ Board config to use DDR2. It can be eanbeld for SoCs with
+ Freescale DDR2 or DDR3 controllers, depending on the board
+ implementation.
+
+ CONFIG_SYS_FSL_DDR3
+ Board config to use DDR3. It can be enabled for SoCs with
+ Freescale DDR3 controllers.
+
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
Set for the SPL on PPC mpc8xxx targets, support for
- arch/powerpc/cpu/mpc8xxx/ddr/libddr.o in SPL binary.
+ drivers/ddr/fsl/libddr.o in SPL binary.
CONFIG_SPL_COMMON_INIT_DDR
Set for common ddr init with serial presence detect in
# Stub implementations of cache management functions for USB
obj-y += cache.o
-ifdef CONFIG_FSL_DDR2
-obj-$(CONFIG_MPC8349) += ../mpc85xx/ddr-gen2.o
+ifdef CONFIG_SYS_FSL_DDR2
+obj-$(CONFIG_MPC8349) += $(SRCTREE)/drivers/ddr/fsl/mpc85xx_ddr_gen2.o
else
obj-y += spd_sdram.o
endif
-obj-$(CONFIG_FSL_DDR2) += law.o
+obj-$(CONFIG_SYS_FSL_DDR2) += law.o
endif # not minimal
void ecc_print_status(void)
{
immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-#ifdef CONFIG_FSL_DDR2
+#ifdef CONFIG_SYS_FSL_DDR2
ccsr_ddr_t *ddr = &immap->ddr;
#else
ddr83xx_t *ddr = &immap->ddr;
int do_ecc(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
{
immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-#ifdef CONFIG_FSL_DDR2
+#ifdef CONFIG_SYS_FSL_DDR2
ccsr_ddr_t *ddr = &immap->ddr;
#else
ddr83xx_t *ddr = &immap->ddr;
obj-$(CONFIG_CMD_ERRATA) += cmd_errata.o
obj-$(CONFIG_CPM2) += commproc.o
-# supports ddr1
-obj-$(CONFIG_MPC8540) += ddr-gen1.o
-obj-$(CONFIG_MPC8560) += ddr-gen1.o
-obj-$(CONFIG_MPC8541) += ddr-gen1.o
-obj-$(CONFIG_MPC8555) += ddr-gen1.o
-
-# supports ddr1/2
-obj-$(CONFIG_MPC8548) += ddr-gen2.o
-obj-$(CONFIG_MPC8568) += ddr-gen2.o
-obj-$(CONFIG_MPC8544) += ddr-gen2.o
-
-# supports ddr1/2/3
-obj-$(CONFIG_PPC_C29X) += ddr-gen3.o
-obj-$(CONFIG_MPC8572) += ddr-gen3.o
-obj-$(CONFIG_MPC8536) += ddr-gen3.o
-obj-$(CONFIG_MPC8569) += ddr-gen3.o
-obj-$(CONFIG_P1010) += ddr-gen3.o
-obj-$(CONFIG_P1011) += ddr-gen3.o
-obj-$(CONFIG_P1012) += ddr-gen3.o
-obj-$(CONFIG_P1013) += ddr-gen3.o
-obj-$(CONFIG_P1014) += ddr-gen3.o
-obj-$(CONFIG_P1020) += ddr-gen3.o
-obj-$(CONFIG_P1021) += ddr-gen3.o
-obj-$(CONFIG_P1022) += ddr-gen3.o
-obj-$(CONFIG_P1023) += ddr-gen3.o
-obj-$(CONFIG_P1024) += ddr-gen3.o
-obj-$(CONFIG_P1025) += ddr-gen3.o
-obj-$(CONFIG_P2010) += ddr-gen3.o
-obj-$(CONFIG_P2020) += ddr-gen3.o
-obj-$(CONFIG_PPC_P2041) += ddr-gen3.o
-obj-$(CONFIG_PPC_P3041) += ddr-gen3.o
-obj-$(CONFIG_PPC_P4080) += ddr-gen3.o
-obj-$(CONFIG_PPC_P5020) += ddr-gen3.o
-obj-$(CONFIG_PPC_P5040) += ddr-gen3.o
-obj-$(CONFIG_PPC_T4240) += ddr-gen3.o
-obj-$(CONFIG_PPC_T4160) += ddr-gen3.o
-obj-$(CONFIG_PPC_B4420) += ddr-gen3.o
-obj-$(CONFIG_PPC_B4860) += ddr-gen3.o
-obj-$(CONFIG_BSC9131) += ddr-gen3.o
-obj-$(CONFIG_BSC9132) += ddr-gen3.o
-obj-$(CONFIG_PPC_T1040) += ddr-gen3.o
-obj-$(CONFIG_PPC_T1042) += ddr-gen3.o
-obj-$(CONFIG_PPC_T1020) += ddr-gen3.o
-obj-$(CONFIG_PPC_T1022) += ddr-gen3.o
-
obj-$(CONFIG_CPM2) += ether_fcc.o
obj-$(CONFIG_OF_LIBFDT) += fdt.o
obj-$(CONFIG_FSL_CORENET) += liodn.o
#include <asm/fsl_lbc.h>
#include <post.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
DECLARE_GLOBAL_DATA_PTR;
for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
switch (i) {
case 0:
- ddr[i] = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ ddr[i] = (void *)CONFIG_SYS_FSL_DDR_ADDR;
break;
-#if defined(CONFIG_SYS_MPC8xxx_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1)
+#if defined(CONFIG_SYS_FSL_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1)
case 1:
- ddr[i] = (void *)CONFIG_SYS_MPC8xxx_DDR2_ADDR;
+ ddr[i] = (void *)CONFIG_SYS_FSL_DDR2_ADDR;
break;
#endif
-#if defined(CONFIG_SYS_MPC8xxx_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2)
+#if defined(CONFIG_SYS_FSL_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2)
case 2:
- ddr[i] = (void *)CONFIG_SYS_MPC8xxx_DDR3_ADDR;
+ ddr[i] = (void *)CONFIG_SYS_FSL_DDR3_ADDR;
break;
#endif
-#if defined(CONFIG_SYS_MPC8xxx_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3)
+#if defined(CONFIG_SYS_FSL_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3)
case 3:
- ddr[i] = (void *)CONFIG_SYS_MPC8xxx_DDR4_ADDR;
+ ddr[i] = (void *)CONFIG_SYS_FSL_DDR4_ADDR;
break;
#endif
default:
#include <asm/io.h>
#include <asm/mmu.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include "mp.h"
DECLARE_GLOBAL_DATA_PTR;
obj-y += cpu.o
obj-y += cpu_init.o
-# 8610 & 8641 are identical w/regards to DDR
-obj-$(CONFIG_MPC8610) += ddr-8641.o
-obj-$(CONFIG_MPC8641) += ddr-8641.o
obj-$(CONFIG_OF_LIBFDT) += fdt.o
obj-y += interrupts.o
obj-$(CONFIG_MP) += mp.o
obj-$(CONFIG_FSL_LAW) += law.o
endif
-
-ifdef CONFIG_SPL_BUILD
-obj-$(CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/
-else
-obj-y += ddr/
-endif
+++ /dev/null
-#
-# Copyright 2008-2011 Freescale Semiconductor, Inc.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License
-# Version 2 as published by the Free Software Foundation.
-#
-
-obj-$(CONFIG_FSL_DDR1) += main.o util.o ctrl_regs.o options.o \
- lc_common_dimm_params.o
-
-obj-$(CONFIG_FSL_DDR2) += main.o util.o ctrl_regs.o options.o \
- lc_common_dimm_params.o
-
-obj-$(CONFIG_FSL_DDR3) += main.o util.o ctrl_regs.o options.o \
- lc_common_dimm_params.o
-ifdef CONFIG_DDR_SPD
-SPD := y
-endif
-ifdef CONFIG_SPD_EEPROM
-SPD := y
-endif
-ifdef SPD
-obj-$(CONFIG_FSL_DDR1) += ddr1_dimm_params.o
-obj-$(CONFIG_FSL_DDR2) += ddr2_dimm_params.o
-obj-$(CONFIG_FSL_DDR3) += ddr3_dimm_params.o
-endif
-
-obj-$(CONFIG_FSL_DDR_INTERACTIVE) += interactive.o
#ifdef CONFIG_MPC85xx
#include <asm/config_mpc85xx.h>
+#define CONFIG_SYS_FSL_DDR
#endif
#ifdef CONFIG_MPC86xx
#include <asm/config_mpc86xx.h>
+#define CONFIG_SYS_FSL_DDR
+#endif
+
+#ifdef CONFIG_MPC83xx
+#define CONFIG_SYS_FSL_DDR
#endif
#ifndef HWCONFIG_BUFFER_SIZE
#elif defined(CONFIG_MPC8540)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 8
+#define CONFIG_SYS_FSL_DDRC_GEN1
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8541)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 8
+#define CONFIG_SYS_FSL_DDRC_GEN1
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8544)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 10
+#define CONFIG_SYS_FSL_DDRC_GEN2
#define CONFIG_SYS_PPC_E500_DEBUG_TLB 0
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8548)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 10
+#define CONFIG_SYS_FSL_DDRC_GEN2
#define CONFIG_SYS_PPC_E500_DEBUG_TLB 0
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8555)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 8
+#define CONFIG_SYS_FSL_DDRC_GEN1
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8560)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 8
+#define CONFIG_SYS_FSL_DDRC_GEN1
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8568)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 10
+#define CONFIG_SYS_FSL_DDRC_GEN2
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define QE_MURAM_SIZE 0x10000UL
#define MAX_QE_RISC 2
#define CONFIG_SYS_FSL_THREADS_PER_CORE 1
#endif
+#if !defined(CONFIG_SYS_FSL_DDRC_GEN1) && \
+ !defined(CONFIG_SYS_FSL_DDRC_GEN2) && \
+ !defined(CONFIG_SYS_FSL_DDRC_GEN3)
+#define CONFIG_SYS_FSL_DDRC_GEN3
+#endif
+
#endif /* _ASM_MPC85xx_CONFIG_H_ */
#ifndef _ASM_MPC86xx_CONFIG_H_
#define _ASM_MPC86xx_CONFIG_H_
+#define CONFIG_SYS_FSL_DDR_86XX
+
/* SoC specific defines for Freescale MPC86xx processors */
#if defined(CONFIG_MPC8610)
/*
* DDR Memory Controller Memory Map
*/
-#if defined(CONFIG_FSL_DDR2) || defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR2) || defined(CONFIG_SYS_FSL_DDR3)
typedef struct ccsr_ddr {
u32 cs0_bnds; /* Chip Select 0 Memory Bounds */
u8 res1[4];
u8 dll_ddr[0x100];
u8 dll_lbc[0x100];
u8 res1[0xE00];
-#if defined(CONFIG_FSL_DDR2) || defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR2) || defined(CONFIG_SYS_FSL_DDR3)
ccsr_ddr_t ddr; /* DDR Memory Controller Memory */
#else
ddr83xx_t ddr; /* DDR Memory Controller Memory */
#endif
#define CONFIG_SYS_MPC8xxx_DDR_OFFSET (0x2000)
-#define CONFIG_SYS_MPC8xxx_DDR_ADDR \
+#define CONFIG_SYS_FSL_DDR_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR_OFFSET)
#define CONFIG_SYS_MPC83xx_DMA_OFFSET (0x8000)
#define CONFIG_SYS_MPC83xx_DMA_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_FSL_CORENET_RCPM_OFFSET)
#define CONFIG_SYS_MPC85xx_ECM_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_ECM_OFFSET)
-#define CONFIG_SYS_MPC8xxx_DDR_ADDR \
+#define CONFIG_SYS_FSL_DDR_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR_OFFSET)
-#define CONFIG_SYS_MPC8xxx_DDR2_ADDR \
+#define CONFIG_SYS_FSL_DDR2_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR2_OFFSET)
-#define CONFIG_SYS_MPC8xxx_DDR3_ADDR \
+#define CONFIG_SYS_FSL_DDR3_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR3_OFFSET)
#define CONFIG_SYS_LBC_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_LBC_OFFSET)
extern immap_t *immr;
#define CONFIG_SYS_MPC8xxx_DDR_OFFSET 0x2000
-#define CONFIG_SYS_MPC8xxx_DDR_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR_OFFSET)
+#define CONFIG_SYS_FSL_DDR_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR_OFFSET)
#define CONFIG_SYS_MPC8xxx_DDR2_OFFSET 0x6000
-#define CONFIG_SYS_MPC8xxx_DDR2_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR2_OFFSET)
+#define CONFIG_SYS_FSL_DDR2_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR2_OFFSET)
#define CONFIG_SYS_MPC86xx_DMA_OFFSET 0x21000
#define CONFIG_SYS_MPC86xx_DMA_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_MPC86xx_DMA_OFFSET)
#define CONFIG_SYS_MPC86xx_PIC_OFFSET 0x40000
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/io.h>
#include <miiphy.h>
#include <libfdt.h>
* and delay a while before we continue.
*/
if (mpc85xx_gpio_get(GPIO_RESETS)) {
- ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_FSL_DDR_ADDR;
puts("Debugger detected... extra device reset enabled!\n");
#include <common.h>
#include <i2c.h>
#include <hwconfig.h>
+#include <fsl_ddr.h>
#include <asm/mmu.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
-#include <../arch/powerpc/cpu/mpc8xxx/ddr/ddr.h>
DECLARE_GLOBAL_DATA_PTR;
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <nand.h>
#include <linux/compiler.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/global_data.h>
DECLARE_GLOBAL_DATA_PTR;
*/
static void sdram_init(void)
{
- ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_FSL_DDR_ADDR;
__raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds);
__raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config);
#include <asm/fsl_ifc.h>
#include <hwconfig.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#ifdef CONFIG_PCI
#include <pci.h>
*to the DSP DDR controller as connected DDR memories are similar.
*/
ccsr_ddr_t __iomem *pa_ddr =
- (ccsr_ddr_t __iomem *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ (ccsr_ddr_t __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
ccsr_ddr_t temp_ddr;
ccsr_ddr_t __iomem *dsp_ddr =
(ccsr_ddr_t __iomem *)CONFIG_SYS_FSL_DSP_CCSR_DDR_ADDR;
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <nand.h>
#include <linux/compiler.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/global_data.h>
DECLARE_GLOBAL_DATA_PTR;
static void sdram_init(void)
{
- ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_FSL_DDR_ADDR;
#if CONFIG_DDR_CLK_FREQ == 100000000
__raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds);
__raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config);
#include <common.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include "cpld.h"
#include <i2c.h>
#include <hwconfig.h>
#include <asm/mmu.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
DECLARE_GLOBAL_DATA_PTR;
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <asm/fsl_portals.h>
#include <asm/fsl_liodn.h>
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
fixed_ddr_parm_t fixed_ddr_parm_0[] = {
{0, 0, NULL}
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#define CONFIG_SYS_DDR_TIMING_3_1200 0x01030000
#define CONFIG_SYS_DDR_TIMING_0_1200 0xCC550104
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
fixed_ddr_parm_t fixed_ddr_parm_0[] = {
{0, 0, NULL}
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
fixed_ddr_parm_t fixed_ddr_parm_0[] = {
{0, 0, NULL}
obj-y += mpc8349emds.o
obj-$(CONFIG_PCI) += pci.o
-obj-$(CONFIG_FSL_DDR2) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR2) += ddr.o
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
struct board_specific_parameters {
u32 n_ranks;
#include <i2c.h>
#include <spi.h>
#include <miiphy.h>
-#ifdef CONFIG_FSL_DDR2
-#include <asm/fsl_ddr_sdram.h>
+#ifdef CONFIG_SYS_FSL_DDR2
+#include <fsl_ddr_sdram.h>
#else
#include <spd_sdram.h>
#endif
/* DDR SDRAM - Main SODIMM */
im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_BASE & LAWBAR_BAR;
#if defined(CONFIG_SPD_EEPROM)
-#ifndef CONFIG_FSL_DDR2
+#ifndef CONFIG_SYS_FSL_DDR2
msize = spd_sdram() * 1024 * 1024;
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
ddr_enable_ecc(msize);
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/io.h>
#include <asm/fsl_serdes.h>
#include <spd.h>
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <libfdt.h>
#include <fdt_support.h>
phys_size_t fixed_sdram(void)
{
#ifndef CONFIG_SYS_RAMBOOT
- volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC8xxx_DDR_ADDR);
+ volatile ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_FSL_DDR_ADDR);
ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <ioports.h>
#include <spd_sdram.h>
#include <libfdt.h>
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <asm/io.h>
#include <miiphy.h>
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <miiphy.h>
#include <libfdt.h>
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <ioports.h>
#include <spd_sdram.h>
#include <libfdt.h>
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <ioports.h>
#include <spd_sdram.h>
#include <miiphy.h>
phys_size_t fixed_sdram(void)
{
#ifndef CONFIG_SYS_RAMBOOT
- volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC8xxx_DDR_ADDR);
+ volatile ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_FSL_DDR_ADDR);
ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <spd_sdram.h>
#include <i2c.h>
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <asm/io.h>
#include <spd_sdram.h>
#if !defined(CONFIG_SPD_EEPROM)
phys_size_t fixed_sdram(void)
{
- volatile ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ volatile ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_FSL_DDR_ADDR;
uint d_init;
out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS);
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
struct board_specific_parameters {
u32 n_ranks;
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/io.h>
#include <asm/fsl_serdes.h>
#include <miiphy.h>
#
obj-y += mpc8610hpcd.o
-obj-$(CONFIG_FSL_DDR2) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR2) += ddr.o
obj-y += law.o
obj-$(CONFIG_FSL_DIU_FB) += mpc8610hpcd_diu.o
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/processor.h>
#include <asm/immap_86xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <i2c.h>
#include <asm/io.h>
obj-y += mpc8641hpcn.o
obj-y += law.o
-obj-$(CONFIG_FSL_DDR2) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR2) += ddr.o
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
struct board_specific_parameters {
u32 n_ranks;
#include <asm/processor.h>
#include <asm/immap_86xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <asm/io.h>
#include <libfdt.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <nand.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_law.h>
#include <asm/global_data.h>
void sdram_init(void)
{
- ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_FSL_DDR_ADDR;
ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
u32 ddr_ratio;
unsigned long ddr_freq_mhz;
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
struct board_specific_parameters {
u32 n_ranks;
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <asm/io.h>
#include <libfdt.h>
#include <asm/io.h>
#include <nand.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
const static u32 sysclk_tbl[] = {
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_portals.h>
#include <libfdt.h>
#include <fdt_support.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_portals.h>
#include <libfdt.h>
#include <fdt_support.h>
phys_size_t fixed_sdram(void)
{
#ifndef CONFIG_SYS_RAMBOOT
- ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_FSL_DDR_ADDR;
set_next_law(0, LAW_SIZE_2G, LAW_TRGT_IF_DDR_1);
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <asm/fsl_lbc.h>
#include <nand.h>
#include <linux/compiler.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/global_data.h>
DECLARE_GLOBAL_DATA_PTR;
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <asm/fsl_lbc.h>
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
struct board_specific_parameters {
u32 n_ranks;
* num| hi| clk| cpo|wrdata|2T
* ranks| mhz|adjst| | delay|
*/
-#ifdef CONFIG_FSL_DDR2
+#ifdef CONFIG_SYS_FSL_DDR2
{2, 549, 4, 0x1f, 2, 0},
{2, 680, 4, 0x1f, 3, 0},
{2, 850, 4, 0x1f, 4, 0},
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/io.h>
#include <asm/fsl_serdes.h>
#include <miiphy.h>
phys_size_t fixed_sdram(void)
{
- volatile ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ volatile ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_FSL_DDR_ADDR;
uint d_init;
ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
#include <i2c.h>
#include <hwconfig.h>
#include <asm/mmu.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
struct board_specific_parameters {
#include <i2c.h>
#include <hwconfig.h>
#include <asm/mmu.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
#include "ddr.h"
#include <i2c.h>
#include <hwconfig.h>
#include <asm/mmu.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
#include "ddr.h"
#include <i2c.h>
#include <hwconfig.h>
#include <asm/mmu.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
#include "ddr.h"
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <asm/fsl_portals.h>
#include <asm/fsl_liodn.h>
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <asm/io.h>
#include <libfdt.h>
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts, dimm_params_t *pdimm,
unsigned int ctrl_num)
#include <i2c.h>
#include <hwconfig.h>
#include <asm/mmu.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
obj-y += sbc8548.o
obj-y += law.o
obj-y += tlb.o
-obj-$(CONFIG_FSL_DDR2) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR2) += ddr.o
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
*/
phys_size_t fixed_sdram(void)
{
- volatile ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_MPC8xxx_DDR_ADDR);
+ volatile ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_FSL_DDR_ADDR);
out_be32(&ddr->cs0_bnds, 0x0000007f);
out_be32(&ddr->cs1_bnds, 0x008000ff);
#include <asm/processor.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <spd_sdram.h>
#include <netdev.h>
obj-y += sbc8641d.o
obj-y += law.o
-obj-$(CONFIG_FSL_DDR2) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR2) += ddr.o
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/processor.h>
#include <asm/immap_86xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <libfdt.h>
#include <fdt_support.h>
obj-y += tlb.o
obj-y += nand.o
obj-y += sdram.o
-obj-$(CONFIG_FSL_DDR2) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR2) += ddr.o
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <common.h>
#include <asm/processor.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/processor.h>
#include <asm/mmu.h>
#include <spd_sdram.h>
*/
phys_size_t fixed_sdram(void)
{
- volatile ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_MPC8xxx_DDR_ADDR);
+ volatile ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_FSL_DDR_ADDR);
/*
* Disable memory controller.
obj-y += law.o
obj-y += tlb.o
obj-y += flash.o
-obj-$(CONFIG_FSL_DDR1) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR1) += ddr.o
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <ioports.h>
#include <asm/io.h>
#include <spd_sdram.h>
obj-y += stxssa.o
obj-y += law.o
obj-y += tlb.o
-obj-$(CONFIG_FSL_DDR1) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR1) += ddr.o
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <ioports.h>
#include <asm/io.h>
#include <spd_sdram.h>
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address)
{
#include <common.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/mmu.h>
#include <asm/io.h>
#include <fdt_support.h>
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
{
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address)
{
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void get_spd(ddr3_spd_eeprom_t *spd, u8 i2c_address)
{
--- /dev/null
+#
+# Copyright 2008-2011 Freescale Semiconductor, Inc.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License
+# Version 2 as published by the Free Software Foundation.
+#
+
+obj-$(CONFIG_SYS_FSL_DDR1) += main.o util.o ctrl_regs.o options.o \
+ lc_common_dimm_params.o
+
+obj-$(CONFIG_SYS_FSL_DDR2) += main.o util.o ctrl_regs.o options.o \
+ lc_common_dimm_params.o
+
+obj-$(CONFIG_SYS_FSL_DDR3) += main.o util.o ctrl_regs.o options.o \
+ lc_common_dimm_params.o
+ifdef CONFIG_DDR_SPD
+SPD := y
+endif
+ifdef CONFIG_SPD_EEPROM
+SPD := y
+endif
+ifdef SPD
+obj-$(CONFIG_SYS_FSL_DDR1) += ddr1_dimm_params.o
+obj-$(CONFIG_SYS_FSL_DDR2) += ddr2_dimm_params.o
+obj-$(CONFIG_SYS_FSL_DDR3) += ddr3_dimm_params.o
+endif
+
+obj-$(CONFIG_FSL_DDR_INTERACTIVE) += interactive.o
+obj-$(CONFIG_SYS_FSL_DDRC_GEN1) += mpc85xx_ddr_gen1.o
+obj-$(CONFIG_SYS_FSL_DDRC_GEN2) += mpc85xx_ddr_gen2.o
+obj-$(CONFIG_SYS_FSL_DDRC_GEN3) += mpc85xx_ddr_gen3.o
+obj-$(CONFIG_SYS_FSL_DDR_86XX) += mpc86xx_ddr.o
+obj-$(CONFIG_FSL_DDR_INTERACTIVE) += interactive.o
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
-#include "ddr.h"
+#include <fsl_ddr.h>
+#include <asm/io.h>
-#define _DDR_ADDR CONFIG_SYS_MPC8xxx_DDR_ADDR
+#define _DDR_ADDR CONFIG_SYS_FSL_DDR_ADDR
static u32 fsl_ddr_get_version(void)
{
{
int rtt;
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
rtt = 0;
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
rtt = 3;
#else
rtt = 0;
/* -3E = 667 CL5, -25 = CL6 800, -25E = CL5 800 */
-#if !defined(CONFIG_FSL_DDR1)
+#if !defined(CONFIG_SYS_FSL_DDR1)
static inline int avoid_odt_overlap(const dimm_params_t *dimm_params)
{
#if CONFIG_DIMM_SLOTS_PER_CTLR == 1
/* Mode register set cycle time (tMRD). */
unsigned char tmrd_mclk;
-#ifdef CONFIG_FSL_DDR3
+#ifdef CONFIG_SYS_FSL_DDR3
/*
* (tXARD and tXARDS). Empirical?
* The DDR3 spec has not tXARD,
pre_pd_exit_mclk = act_pd_exit_mclk;
taxpd_mclk = 1;
}
-#else /* CONFIG_FSL_DDR2 */
+#else /* CONFIG_SYS_FSL_DDR2 */
/*
* (tXARD and tXARDS). Empirical?
* tXARD = 2 for DDR2
);
debug("FSLDDR: timing_cfg_0 = 0x%08x\n", ddr->timing_cfg_0);
}
-#endif /* defined(CONFIG_FSL_DDR2) */
+#endif /* defined(CONFIG_SYS_FSL_DDR2) */
/* DDR SDRAM Timing Configuration 3 (TIMING_CFG_3) */
static void set_timing_cfg_3(fsl_ddr_cfg_regs_t *ddr,
* 4.5 1000
* 5.0 5 1001
*/
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
caslat_ctrl = (cas_latency + 1) & 0x07;
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
caslat_ctrl = 2 * cas_latency - 1;
#else
/*
/*
* JEDEC has min requirement for tRRD
*/
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
if (acttoact_mclk < 4)
acttoact_mclk = 4;
#endif
/*
* JEDEC has some min requirements for tWTR
*/
-#if defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR2)
if (wrtord_mclk < 2)
wrtord_mclk = 2;
-#elif defined(CONFIG_FSL_DDR3)
+#elif defined(CONFIG_SYS_FSL_DDR3)
if (wrtord_mclk < 4)
wrtord_mclk = 4;
#endif
add_lat_mclk = additive_latency;
cpo = popts->cpo_override;
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
/*
* This is a lie. It should really be 1, but if it is
* set to 1, bits overlap into the old controller's
* the HW will magically treat it as 1 for DDR 1. Oh Yea.
*/
wr_lat = 0;
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
wr_lat = cas_latency - 1;
#else
wr_lat = compute_cas_write_latency();
/*
* JEDEC has some min requirements for tRTP
*/
-#if defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR2)
if (rd_to_pre < 2)
rd_to_pre = 2;
-#elif defined(CONFIG_FSL_DDR3)
+#elif defined(CONFIG_SYS_FSL_DDR3)
if (rd_to_pre < 4)
rd_to_pre = 4;
#endif
* * ({EXT_REFREC || REFREC} + 8 + 2)]}
* << DDR_SDRAM_INTERVAL[REFINT]
*/
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
obc_cfg = popts->otf_burst_chop_en;
#else
obc_cfg = 0;
d_init = 0;
#endif
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
md_en = popts->mirrored_dimm;
#endif
qd_en = popts->quad_rank_present ? 1 : 0;
unsigned short esdmode2 = 0; /* Extended SDRAM mode 2 */
unsigned short esdmode3 = 0; /* Extended SDRAM mode 3 */
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
int i;
unsigned int rtt_wr = 0; /* Rtt_WR - dynamic ODT off */
unsigned int srt = 0; /* self-refresh temerature, normal range */
);
debug("FSLDDR: ddr_sdram_mode_2 = 0x%08x\n", ddr->ddr_sdram_mode_2);
-#ifdef CONFIG_FSL_DDR3
+#ifdef CONFIG_SYS_FSL_DDR3
if (unq_mrs_en) { /* unique mode registers are supported */
for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
if (popts->rtt_override)
debug("FSLDDR: ddr_sdram_interval = 0x%08x\n", ddr->ddr_sdram_interval);
}
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
/* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */
static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts,
}
}
-#else /* !CONFIG_FSL_DDR3 */
+#else /* !CONFIG_SYS_FSL_DDR3 */
/* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */
static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr,
unsigned int bt;
unsigned int bl; /* BL: Burst Length */
-#if defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR2)
const unsigned int mclk_ps = get_memory_clk_period_ps();
#endif
dqs_en = !popts->dqs_config;
*/
pd = 0;
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
wr = 0; /* Historical */
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
wr = (common_dimm->twr_ps + mclk_ps - 1) / mclk_ps - 1;
#endif
dll_res = 0;
mode = 0;
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
if (1 <= cas_latency && cas_latency <= 4) {
unsigned char mode_caslat_table[4] = {
0x5, /* 1.5 clocks */
} else {
printf("Warning: unknown cas_latency %d\n", cas_latency);
}
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
caslat = cas_latency;
#endif
bt = 0;
unsigned int wwt = 0; /* Write-to-write turnaround for same CS */
unsigned int dll_lock = 0; /* DDR SDRAM DLL Lock Time */
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
if (popts->burst_length == DDR_BL8) {
/* We set BL/2 for fixed BL8 */
rrt = 0; /* BL/2 clocks */
unsigned int wodt_on = 0; /* Write to ODT on */
unsigned int wodt_off = 0; /* Write to ODT off */
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
/* rodt_on = timing_cfg_1[caslat] - timing_cfg_2[wrlat] + 1 */
rodt_on = cas_latency - ((ddr->timing_cfg_2 & 0x00780000) >> 19) + 1;
rodt_off = 4; /* 4 clocks */
set_ddr_eor(ddr, popts);
-#if !defined(CONFIG_FSL_DDR1)
+#if !defined(CONFIG_SYS_FSL_DDR1)
set_timing_cfg_0(ddr, popts, dimm_params);
#endif
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
-#include "ddr.h"
+#include <fsl_ddr.h>
/*
* Calculate the Density of each Physical Rank.
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
-#include "ddr.h"
+#include <fsl_ddr.h>
/*
* Calculate the Density of each Physical Rank.
* Returned size is in bytes.
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
-#include "ddr.h"
+#include <fsl_ddr.h>
/*
* Calculate the Density of each Physical Rank.
#include <common.h>
#include <linux/ctype.h>
#include <asm/types.h>
+#include <asm/io.h>
-#include <asm/fsl_ddr_sdram.h>
-#include "ddr.h"
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr.h>
/* Option parameter Structures */
struct options_string {
CTRL_OPTIONS_CS(3, odt_rd_cfg),
CTRL_OPTIONS_CS(3, odt_wr_cfg),
#endif
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
CTRL_OPTIONS_CS(0, odt_rtt_norm),
CTRL_OPTIONS_CS(0, odt_rtt_wr),
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1)
CTRL_OPTIONS_CS(3, odt_rd_cfg),
CTRL_OPTIONS_CS(3, odt_wr_cfg),
#endif
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
CTRL_OPTIONS_CS(0, odt_rtt_norm),
CTRL_OPTIONS_CS(0, odt_rtt_wr),
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1)
print_option_table(options, n_opts, popts);
}
-#ifdef CONFIG_FSL_DDR1
+#ifdef CONFIG_SYS_FSL_DDR1
void ddr1_spd_dump(const ddr1_spd_eeprom_t *spd)
{
unsigned int i;
}
#endif
-#ifdef CONFIG_FSL_DDR2
+#ifdef CONFIG_SYS_FSL_DDR2
void ddr2_spd_dump(const ddr2_spd_eeprom_t *spd)
{
unsigned int i;
}
#endif
-#ifdef CONFIG_FSL_DDR3
+#ifdef CONFIG_SYS_FSL_DDR3
void ddr3_spd_dump(const ddr3_spd_eeprom_t *spd)
{
unsigned int i;
static inline void generic_spd_dump(const generic_spd_eeprom_t *spd)
{
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
ddr1_spd_dump(spd);
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
ddr2_spd_dump(spd);
-#elif defined(CONFIG_FSL_DDR3)
+#elif defined(CONFIG_SYS_FSL_DDR3)
ddr3_spd_dump(spd);
#endif
}
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
-#include "ddr.h"
+#include <fsl_ddr.h>
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
static unsigned int
compute_cas_latency_ddr3(const dimm_params_t *dimm_params,
common_timing_params_t *outpdimm,
unsigned int temp1, temp2;
unsigned int additive_latency = 0;
-#if !defined(CONFIG_FSL_DDR3)
+#if !defined(CONFIG_SYS_FSL_DDR3)
const unsigned int mclk_ps = get_memory_clk_period_ps();
unsigned int lowest_good_caslat;
unsigned int not_ok;
if (temp1 != 0)
printf("ERROR: Mix different RDIMM detected!\n");
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
if (compute_cas_latency_ddr3(dimm_params, outpdimm, number_of_dimms))
return 1;
#else
}
outpdimm->highest_common_derated_caslat = temp1;
debug("highest common dereated CAS latency = %u\n", temp1);
-#endif /* #if defined(CONFIG_FSL_DDR3) */
+#endif /* #if defined(CONFIG_SYS_FSL_DDR3) */
/* Determine if all DIMMs ECC capable. */
temp1 = 1;
}
outpdimm->all_dimms_ecc_capable = temp1;
-#ifndef CONFIG_FSL_DDR3
+#ifndef CONFIG_SYS_FSL_DDR3
/* FIXME: move to somewhere else to validate. */
if (mclk_ps > tckmax_max_ps) {
printf("Warning: some of the installed DIMMs "
additive_latency = 0;
-#if defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR2)
if (lowest_good_caslat < 4) {
additive_latency = (picos_to_mclk(trcd_ps) > lowest_good_caslat)
? picos_to_mclk(trcd_ps) - lowest_good_caslat : 0;
}
}
-#elif defined(CONFIG_FSL_DDR3)
+#elif defined(CONFIG_SYS_FSL_DDR3)
/*
* The system will not use the global auto-precharge mode.
* However, it uses the page mode, so we set AL=0
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_law.h>
-#include "ddr.h"
+#include <fsl_ddr.h>
void fsl_ddr_set_lawbar(
const common_timing_params_t *memctl_common_params,
#include <common.h>
#include <asm/io.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
unsigned int ctrl_num, int step)
{
unsigned int i;
- volatile ccsr_ddr_t *ddr = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ volatile ccsr_ddr_t *ddr = (void *)CONFIG_SYS_FSL_DDR_ADDR;
if (ctrl_num != 0) {
printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
void
ddr_enable_ecc(unsigned int dram_size)
{
- volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC8xxx_DDR_ADDR);
+ volatile ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_FSL_DDR_ADDR);
dma_meminit(CONFIG_MEM_INIT_VALUE, dram_size);
#include <common.h>
#include <asm/io.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
unsigned int ctrl_num, int step)
{
unsigned int i;
- ccsr_ddr_t *ddr = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ ccsr_ddr_t *ddr = (void *)CONFIG_SYS_FSL_DDR_ADDR;
#if defined(CONFIG_SYS_FSL_ERRATUM_NMG_DDR120) && defined(CONFIG_MPC85xx)
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
#include <common.h>
#include <asm/io.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/processor.h>
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
switch (ctrl_num) {
case 0:
- ddr = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ ddr = (void *)CONFIG_SYS_FSL_DDR_ADDR;
break;
-#if defined(CONFIG_SYS_MPC8xxx_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1)
+#if defined(CONFIG_SYS_FSL_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1)
case 1:
- ddr = (void *)CONFIG_SYS_MPC8xxx_DDR2_ADDR;
+ ddr = (void *)CONFIG_SYS_FSL_DDR2_ADDR;
break;
#endif
-#if defined(CONFIG_SYS_MPC8xxx_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2)
+#if defined(CONFIG_SYS_FSL_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2)
case 2:
- ddr = (void *)CONFIG_SYS_MPC8xxx_DDR3_ADDR;
+ ddr = (void *)CONFIG_SYS_FSL_DDR3_ADDR;
break;
#endif
-#if defined(CONFIG_SYS_MPC8xxx_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3)
+#if defined(CONFIG_SYS_FSL_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3)
case 3:
- ddr = (void *)CONFIG_SYS_MPC8xxx_DDR4_ADDR;
+ ddr = (void *)CONFIG_SYS_FSL_DDR4_ADDR;
break;
#endif
default:
#include <common.h>
#include <asm/io.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
switch (ctrl_num) {
case 0:
- ddr = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ ddr = (void *)CONFIG_SYS_FSL_DDR_ADDR;
break;
case 1:
- ddr = (void *)CONFIG_SYS_MPC8xxx_DDR2_ADDR;
+ ddr = (void *)CONFIG_SYS_FSL_DDR2_ADDR;
break;
default:
printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
#include <common.h>
#include <hwconfig.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
-#include "ddr.h"
+#include <fsl_ddr.h>
/*
* Use our own stack based buffer before relocation to allow accessing longer
unsigned int odt_rtt_wr;
};
-#ifdef CONFIG_FSL_DDR3
+#ifdef CONFIG_SYS_FSL_DDR3
static const struct dynamic_odt single_Q[4] = {
{ /* cs0 */
FSL_DDR_ODT_NEVER,
DDR3_RTT_OFF
}
};
-#else /* CONFIG_FSL_DDR3 */
+#else /* CONFIG_SYS_FSL_DDR3 */
static const struct dynamic_odt single_Q[4] = {
{0, 0, 0, 0},
{0, 0, 0, 0},
unsigned int i;
char buffer[HWCONFIG_BUFFER_SIZE];
char *buf = NULL;
-#if defined(CONFIG_FSL_DDR3) || defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR2)
const struct dynamic_odt *pdodt = odt_unknown;
#endif
ulong ddr_freq;
if (getenv_f("hwconfig", buffer, sizeof(buffer)) > 0)
buf = buffer;
-#if defined(CONFIG_FSL_DDR3) || defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR2)
/* Chip select options. */
if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
switch (pdimm[0].n_ranks) {
/* Pick chip-select local options. */
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
-#if defined(CONFIG_FSL_DDR3) || defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR2)
popts->cs_local_opts[i].odt_rd_cfg = pdodt[i].odt_rd_cfg;
popts->cs_local_opts[i].odt_wr_cfg = pdodt[i].odt_wr_cfg;
popts->cs_local_opts[i].odt_rtt_norm = pdodt[i].odt_rtt_norm;
* 0 for DDR1
* 1 for DDR2
*/
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
popts->dqs_config = 0;
-#elif defined(CONFIG_FSL_DDR2) || defined(CONFIG_FSL_DDR3)
+#elif defined(CONFIG_SYS_FSL_DDR2) || defined(CONFIG_SYS_FSL_DDR3)
popts->dqs_config = 1;
#endif
* presuming all dimms are similar
* 0 = 64-bit, 1 = 32-bit, 2 = 16-bit
*/
-#if defined(CONFIG_FSL_DDR1) || defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR1) || defined(CONFIG_SYS_FSL_DDR2)
if (pdimm[0].n_ranks != 0) {
if ((pdimm[0].data_width >= 64) && \
(pdimm[0].data_width <= 72))
popts->x4_en = (pdimm[0].device_width == 4) ? 1 : 0;
/* Choose burst length. */
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
#if defined(CONFIG_E500MC)
popts->otf_burst_chop_en = 0; /* on-the-fly burst chop disable */
popts->burst_length = DDR_BL8; /* Fixed 8-beat burst len */
#endif
/* Choose ddr controller address mirror mode */
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
popts->mirrored_dimm = pdimm[0].mirrored_dimm;
#endif
* FIXME: varies depending upon number of column addresses or data
* FIXME: width, was considering looking at pdimm->primary_sdram_width
*/
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
popts->tfaw_window_four_activates_ps = mclk_to_picos(1);
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
/*
* x4/x8; some datasheets have 35000
* x16 wide columns only? Use 50000?
*/
popts->tfaw_window_four_activates_ps = 37500;
-#elif defined(CONFIG_FSL_DDR3)
+#elif defined(CONFIG_SYS_FSL_DDR3)
popts->tfaw_window_four_activates_ps = pdimm[0].tfaw_ps;
#endif
popts->zq_en = 0;
popts->wrlvl_en = 0;
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
/*
* due to ddr3 dimm is fly-by topology
* we suggest to enable write leveling to
#include <asm/fsl_law.h>
#include <div64.h>
-#include "ddr.h"
+#include <fsl_ddr.h>
+#include <asm/io.h>
/* To avoid 64-bit full-divides, we factor this here */
#define ULL_2E12 2000000000000ULL
void board_add_ram_info(int use_default)
{
- ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_MPC8xxx_DDR_ADDR);
+ ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_FSL_DDR_ADDR);
#if defined(CONFIG_E6500) && (CONFIG_NUM_DDR_CONTROLLERS == 3)
u32 *mcintl3r = (void *) (CONFIG_SYS_IMMR + 0x18004);
#if CONFIG_NUM_DDR_CONTROLLERS >= 2
if (!(sdram_cfg & SDRAM_CFG_MEM_EN)) {
- ddr = (void __iomem *)CONFIG_SYS_MPC8xxx_DDR2_ADDR;
+ ddr = (void __iomem *)CONFIG_SYS_FSL_DDR2_ADDR;
sdram_cfg = in_be32(&ddr->sdram_cfg);
}
#endif
#if CONFIG_NUM_DDR_CONTROLLERS >= 3
if (!(sdram_cfg & SDRAM_CFG_MEM_EN)) {
- ddr = (void __iomem *)CONFIG_SYS_MPC8xxx_DDR3_ADDR;
+ ddr = (void __iomem *)CONFIG_SYS_FSL_DDR3_ADDR;
sdram_cfg = in_be32(&ddr->sdram_cfg);
}
#endif
#define CONFIG_DDR_SPD
#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_SYS_MEMTEST_END 0x01ffffff
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#undef CONFIG_SYS_DDR_RAW_TIMING
#undef CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_SYS_MEMTEST_END 0x01ffffff
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS1 0x54 /* I2C access */
#define SPD_EEPROM_ADDRESS2 0x56 /* I2C access */
#define CONFIG_PANIC_HANG
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x50
/* -------------------------------------------------------------------- */
/* FreeScale DDR2/3 SDRAM Controller */
-#define CONFIG_FSL_DDR2 /* Our SDRAM slot is DDR2 */
+#define CONFIG_SYS_FSL_DDR2 /* Our SDRAM slot is DDR2 */
#define CONFIG_DDR_ECC /* Enable ECC by default */
#define CONFIG_DDR_SPD /* Detect DDR config from SPD EEPROM */
#define CONFIG_SPD_EEPROM /* ...why 2 config variables for this? */
#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
/*
- * define CONFIG_FSL_DDR2 to use unified DDR driver
+ * define CONFIG_SYS_FSL_DDR2 to use unified DDR driver
* undefine it to use old spd_sdram.c
*/
-#define CONFIG_FSL_DDR2
-#ifdef CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
+#ifdef CONFIG_SYS_FSL_DDR2
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS1 0x52
#define SPD_EEPROM_ADDRESS2 0x51
/* DDR Setup */
#define CONFIG_VERY_BIG_RAM
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#endif
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
/* DDR Setup */
#define CONFIG_VERY_BIG_RAM
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD for DDR */
#define CONFIG_DDR_SPD
/*
* DDR Setup
*/
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 1
/* DDR Setup */
#define CONFIG_DDR_SPD
#define CONFIG_VERY_BIG_RAM
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#ifdef CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_CHIP_SELECTS_PER_CTRL 1
#define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_SDRAM_SIZE 512u /* DDR is 512M */
#define CONFIG_SYS_SPD_BUS_NUM 0
#endif
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
/* DDR Setup */
#define CONFIG_VERY_BIG_RAM
#ifdef CONFIG_DDR2
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#else
-#define CONFIG_FSL_DDR3 1
+#define CONFIG_SYS_FSL_DDR3 1
#endif
/* ECC will be enabled based on perf_mode environment variable */
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x52
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_DDR_SPD
#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x51
#define CONFIG_DDR_SPD
#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x51
#define CONFIG_SYS_SDRAM_SIZE 1024
#define CONFIG_VERY_BIG_RAM
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_SPD_BUS_NUM 1
#define SPD_EEPROM_ADDRESS1 0x51
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#endif
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 1
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M
#define CONFIG_CHIP_SELECTS_PER_CTRL 1
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#undef CONFIG_DDR_ECC /* only for ECC DDR module */
/*
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE
#define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
/*
/*
* DDR config
*/
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
/*
* DDR config
*/
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
/*
* DDR config
*/
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
/*
* DDR config
*/
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#ifndef FSL_DDR_MAIN_H
#define FSL_DDR_MAIN_H
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
-#include "common_timing_params.h"
+#include <common_timing_params.h>
#if defined(CONFIG_DDR_SPD) || defined(CONFIG_SPD_EEPROM)
/*
#define DDR2_RTT_150_OHM 2
#define DDR2_RTT_50_OHM 3
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
#define FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR (1)
typedef ddr1_spd_eeprom_t generic_spd_eeprom_t;
#ifndef CONFIG_FSL_SDRAM_TYPE
#define CONFIG_FSL_SDRAM_TYPE SDRAM_TYPE_DDR1
#endif
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
#define FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR (3)
typedef ddr2_spd_eeprom_t generic_spd_eeprom_t;
#ifndef CONFIG_FSL_SDRAM_TYPE
#define CONFIG_FSL_SDRAM_TYPE SDRAM_TYPE_DDR2
#endif
-#elif defined(CONFIG_FSL_DDR3)
+#elif defined(CONFIG_SYS_FSL_DDR3)
#define FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR (3) /* FIXME */
typedef ddr3_spd_eeprom_t generic_spd_eeprom_t;
#ifndef CONFIG_FSL_SDRAM_TYPE
#define CONFIG_FSL_SDRAM_TYPE SDRAM_TYPE_DDR3
#endif
-#endif /* #if defined(CONFIG_FSL_DDR1) */
+#endif /* #if defined(CONFIG_SYS_FSL_DDR1) */
#define FSL_DDR_ODT_NEVER 0x0
#define FSL_DDR_ODT_CS 0x1
#include <nand.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_law.h>
#define SYSCLK_66 66666666
#include <asm/io.h>
#include <nand.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/global_data.h>
DECLARE_GLOBAL_DATA_PTR;
/* Fixed sdram init -- doesn't use serial presence detect. */
void sdram_init(void)
{
- ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_FSL_DDR_ADDR;
set_next_law(0, LAW_SIZE_2G, LAW_TRGT_IF_DDR_1);
#include <nand.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_law.h>
#define SYSCLK_MASK 0x00200000
LIBS-$(CONFIG_SPL_I2C_SUPPORT) += drivers/i2c/
LIBS-$(CONFIG_SPL_GPIO_SUPPORT) += drivers/gpio/
LIBS-$(CONFIG_SPL_MMC_SUPPORT) += drivers/mmc/
+LIBS-$(CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT) += drivers/ddr/fsl/
LIBS-$(CONFIG_SPL_SERIAL_SUPPORT) += drivers/serial/
LIBS-$(CONFIG_SPL_SPI_FLASH_SUPPORT) += drivers/mtd/spi/
LIBS-$(CONFIG_SPL_SPI_SUPPORT) += drivers/spi/
projects / people / ms / u-boot.git / commitdiff
